This 5 day training course reviews the fundamentals of Casing Design and builds on them to address well design challenges associated with deep, extended reach, HPHT and deepwater wells. Participants will review the theories of both uniaxial and triaxial pipe strength as per API Bulletin 5C3 and ISO/TR 10400, the implications of manufacturing standards and tolerances as per API Specification 5CT and the impact of downhole environmental conditions.

1. www.petroEDGEasia.net
ADVANCED CASING DESIGN
24 – 28 October 2016 | Kuala Lumpur, Malaysia
Your Expert Course Leader
Steve Collard
Steve Collard has 29 yrs of experience as a Drilling Engineer with more than a decade of experience of training in
a broad range of Well Engineering subjects. He served as the examiner for Shell’s “Round 2” Competence
program and was the technical editor of the current Shell Well Engineering Learning Manual, writing all of the
Well Control and Casing Design elements and assisted in the development of their casing seat selection strategies.
Here is what past learners have to say about this training course:
“Steve has done a very good job covering the subject in detailed, provide good explanations & real life examples.” Drilling Engineer,
Talisman Malaysia Limited
“The course massively exceeded my expectation instructor enable me to learn much about casing design ” Senior Drilling Engineer,
Kuwait Energy Egypt
“Steve covered the subjects very well and can tailor the course to be as basic to as detailed as you want it to be. The various ways he can
explain a certain subject make it easier to understand and actually open your eyes to what you thought you know” Drilling Engineering,
Talisman Malaysia Limited
“All DE should take this training before running landmark software” Drilling Engineer|BUT Premier Oil Natuna Sea
“Excellent Course which covered essentials of moderate to advanced skills” Drilliing Engineer/Supervisor, Quadrant Energy Limited
Back by popular demand!

2. Conduct this training course in-house for more effective savings!
Call us at +65 6741 9927 or email to info@asiaedge.net. For more information, visit us at www.petroedgeasia.net
ADVANCED CASING DESIGN
24 – 28 October 2016 | Kuala Lumpur, Malaysia
About this course
This 5 day training course reviews the fundamentals of Casing Design and builds on them
to address well design challenges associated with deep, extended reach, HPHT and
deepwater wells.
Participants will review the theories of both uniaxial and triaxial pipe strength as per API
Bulletin 5C3 and ISO/TR 10400, the implications of manufacturing standards and
tolerances as per API Specification 5CT and the impact of downhole environmental
conditions.
Participants will learn how to optimise preliminary casing design; performing casing seat
selection to satisfy a range of well performance parameters and barrier standards,
select suitable casing sizes to meet well completion objectives and produce a workable
casing scheme utilising casing strings, liners and expandable tubulars. The impact on
casing scheme and cementing program on well abandonment
Participants will master the process of detailed casing design, identifying relevant load
conditions for the lifetime of the well and producing an optimised casing scheme that
can withstand triaxial burst and biaxial collapse loading under downhole conditions.
Service Load design challenges such buckling and trapped annular pressures will be
addressed as well as managing the impact of corrosion and casing wear
Participants will develop an understanding of the how connections are tested using ISO
13679 and how to select suitably pre-qualified connections for use in a well.
The use and limitations of spreadsheets for routine design will be reviewed. The
capabilities and limitations of casing design software for advanced casing design will be
addressed
Who should attend?
Drilling Engineers seeking to develop an advanced understanding of casing design.
While the content will best suit an engineer who is already familiar with the
fundamentals of casing design, there is sufficient review of these principles and
practices to make the course manageable for a Drilling engineer new to the subject.
Course Contents
The course is underpinned by a
Well Design project that runs
throughout the course.
Participants will have the
opportunity to complete
manual and spreadsheet based
casing design calculations to
complete preliminary and
detailed casing design on
production, intermediate and
surface casing strings.
The following modules will
be covered during this
training course:
 Overview of Casing
Classifications and definitions
 Data required for Casing
Design
 Industry Standards and
Specifications
 Formation strength, Kick
Tolerance and Casing seat
selection
 Pipe performance, tolerances
and properties
 Casing Connection
qualification and selection
 Installation, Drilling and
Service Loads for Casing
 Casing design and safety
factors
 Wellhead Selection
 Special Design Considerations
About Your Expert Course Leader
Steve Collard has 29 years of experience as a Drilling Engineer. He joined Shell in 1985 and worked as a Drilling
Engineer and Drilling Supervisor on-site and in the office in a wide range of onshore, offshore and deepwater
environments. Steve has more than a decade of experience of training in a broad range of Well Engineering
subjects. He served as the examiner for Shell’s “Round 2” Competence program and was the technical editor
of the current Shell Well Engineering Learning Manual, writing all of the Well Control and Casing Design
elements and assisted in the development of their casing seat selection strategies. Steve has also consulted
with other Operators on Casing Design Standards. In addition to lecturing and general consultancy in Casing Design, Steve
specialises in Deepwater and HPHT Well Control coaching, rig team building and simulation. He has pioneered the concept
of “Drilling the Well on a Simulator”, working closely with drilling simulator vendors, Operators and Drilling Contractors to
produce a realistic and relevant training environment where integrated rig teams can be exposed to well specific well control
and other operational challenges, develop and then practise responses strategies.

3. Conduct this training course in-house for more effective savings!
Call us at +65 6741 9927 or email to info@asiaedge.net. For more information, visit us at www.petroedgeasia.net
ADVANCED CASING DESIGN
24 – 28 October 2016 | Kuala Lumpur, Malaysia
5 DAY COURSE AGENDA
DAY 1
INTRODUCTION, COURSE OBJECTIVES, PARTICIPANT AND
INSTRUCTOR INTRODUCTIONS
 Functions of Casing
 Well Construction Standards
 The Casing Design Process
 Casing Design Data requirements
PRELIMINARY CASING DESIGN
 Pore Pressures and Formation strengths
 Kick Tolerance and Casing Seat Selection
 Casing setting depth and sizing for Well Construction (Seat
Selection)
 Barriers
 Well Abandonment Considerations
WELL DESIGN PROJECT (Manual / Spreadsheet / Design Software)
DAY 2
Daily Quiz
OIL FIELD TUBULARS
 Industry Standards, Specifications and Documentation
 The Manufacturing Process
 API 5CT
- Steel: Grades, Chemistry, Yield Stress
- Tolerances, Sizes and Lengths
- Inspection
- Supplementary Requirements
 Mechanical properties and Temperature Effects
 Application of ISO 15156 – Materials for us in Sour Service
CASING PERFORMANCE PROPERTIES
 Conventional Casing Strength limits as per API Bulletin 5C3
- Uniaxial Tensile Yield
- Uniaxial (Barlow) Burst
- Uniaxial Collapse, influence of Temperature and Tension
 Alternative Limits proposed in ISO/TR 10400
- Burst Strength based on von Mises Initial Yield
- Burst Strength based on Full Yield
- Alternative Collapse Strength, Effect of Wear on Collapse
Resistance
- Burst Strength, Effect of Wear on Burst Strength and Effect of
Temperature on Burst Strength
 Modes of Failure, Burst, Collapse, Axial, Tri-axial and Joint Integrity
 Buckling – Resistance and Effective Tension
 Design and Safety Factors
CASING CONNECTIONS
 Introduction to Casing Connections
 ISO 13679 Connection Testin
 Selection of Pre-Qualified connections
Spreadsheet Casing Strength calculations and Sensitivity Analysis
using Casing Strength simulators
DAY 3
Daily Quiz
CASING LOADS
 Overview of Design Loads
 Fluid Gradients and Applied Pressures
 Critical Internal and External Pressure Scenarios
 Load Case Selection
 Production Casing Loads
 Intermediate Casing Loads
 Surface Casing Loads
MANUAL DESIGN PROCESS
 Uniaxial Pipe Selection
 Installation Loads
 As Cemented Loads
WELL DESIGN PROJECT (Manual / Spreadsheet / Design Software)
DAY 4
Daily Quiz
SERVICE LOADS
 Load Identification, Production Thermal Profiles
 Thermal Effects on fluids, pipe strength and tension
 Trapped Annular Pressures
 Impact of Cement on Buckling
 Biaxial Collapse Assessment
 Triaxial Burst Assessment
 Pressure Testing
WELL DESIGN PROJECT (Manual / Spreadsheet / Design Software)
DAY 5
Quiz
SPECIAL DESIGN CONSIDERATIONS
 Accounting for Casing Wear and Corrosion
 Deterministic vs Probabilistic Casing Design
 Casing Design for Thermal wells
 Casing Design for HPHT wells
 Casing Design for Deepwater wells
 Annular Pressure Buildup – Prediction, Management and
Mitigation
CASING DESIGN SOFTWARE
 Capabilities and Limitations
Course Wrap up and Close-out

4. Conduct this training course in-house for more effective savings!
Call us at +65 6741 9927 or email to info@asiaedge.net. For more information, visit us at www.petroedgeasia.net
ADVANCED CASING DESIGN
24 – 28 October 2016 | Kuala Lumpur, Malaysia
EARLY BIRD RATE
Register by
24th September 2016
STANDARD RATE
TEAM DISCOUNTS
KUALA LUMPUR | MALAYSIA
24 – 28 October 2016
SGD 5,199 SGD 5,399
petroEDGE recognises the value
of learning in teams.
Group bookings at the same time from
the same
company receive the following:
3 or more at 5% off
5 or more at 7% off
8 of more at 10%
All other promotions including early bird
are exclusive of the group discount.
petroEDGE In-house Training
 Yes, I would like to organise this training on-site and save on total course fees! For further information about On-site
Solutions, please call +65 67419927 or email info@asiaedge.net
DELEGATE DETAILS
Delegate 1
Please note
- Indicate if you have already registered by Phone +Fax +Email +Web
- If you have not received an acknowledgement before the training
course, please call us to confirm your booking.
- Photocopy this form to register multiple delegates.
PAYMENT METHODS
By Cheque/ Bank Draft
Make Payable to Asia Edge Pte. Ltd.
By Direct Transfer
Please quote your invoice number with the remittance advise
Account Name: Asia Edge Pte. Ltd.
Bank Number: 508 Account Number: 762903-001
Swift Code: OCBCSGSG
All bank charges to be borne by payer. Please ensure that Asia Edge Pte
Ltd receives the full invoiced amount.
PAYMENT POLICY
Payment is due in full at the time of registration. Full payment is
mandatory for event attendance. By submitting this registration form,
you have agreed to Asia Edge Pte Ltd’s payment terms
CANCELLATIONS & SUBSTITUTIONS
You may substitute delegates at any time. ASIA EDGE PTE LTD does not
provide refunds for cancellations. For cancellations received in writing
more than seven (7) days prior to the training course you will receive a
100% credit to be used at another ASIA EDGE PTE LTD training course for
up to one year from the date of issuance. For cancellations received
seven (7) days or less prior to an event (including day 7), no credits will
be issued. In the event that ASIA EDGE PTE LTD cancels an event,
delegate payments at the date of cancellation will be credited to a future
ASIA EDGE PTE LTD event. This credit will be available for up to one year
from the date of issuance. In the event that ASIA EDGE PTE LTD
postpones an event, delegate payments at the postponement date will
be credited towards the rescheduled date. If the delegate is unable to
attend the rescheduled event, the delegate will receive a 100% credit
representing payments made towards a future ASIA EDGE PTE LTD
event. This credit will be available for up to one year from the date of
issuance. No refunds will be available for cancellations or
postponements.
ASIA EDGE PTE LTD is not responsible for any loss or damage as a result
of a substitution, alteration or cancellation/postponement of an event.
ASIA EDGE PTE LTD shall assume no liability whatsoever in the event this
training course is cancelled, rescheduled or postponed due to a
fortuitous event, Act of God, unforeseen occurrence or any other event
that renders performance of this training course impracticable or
impossible. For purposes of this clause, a fortuitous event shall include,
but not be limited to: war, fire, labor strike, extreme weather or other
emergency.
PROGRAM CHANGE POLICY
Please note that speakers and topics were confirmed at the time of
publishing; however, circumstances beyond the control of the organizers
may necessitate substitutions, alterations or cancellations of the
speakers and/or topics. As such, ASIA EDGE PTE LTD reserves the right to
alter or modify the advertised speakers and/or topics if necessary. Any
substitutions or alterations will be updated on our web page as soon as
possible.
This brochure may not be copied, photocopied, reproduced, translated,
or converted to any electronic or machine-readable form in whole or in
part without prior written approval of ASIA EDGE PTE LTD
ASIA EDGE PTE. LTD.
Company Registration No: No. 200710561C
Copyright@ 2005 ASIA EDGE PTE LTD. All rights reserved.
 Mr  Ms  Mrs  Dr  Others:
Name :
Job Title :
Department :
Telephone No. :
Email :
Delegate 2
 Mr  Ms  Mrs  Dr  Others:
Name :
Job Title :
Department :
Telephone No. :
Email :
Company :
Address :
Country : Postcode:
Attention
Invoice to :
Telephone No. :
Fax No. :
4 EASY WAYS TO REGISTER
 Online: www.petroedgeasia.net
 Email: info@asiaedge.net
 Phone: +65 6741 9927
 Fax: +65 6747 8737
ADVANCED CASING DESIGN
R E G I S T R A T I O N F O R M