1. MUHAMAD SYAWAL BIN IBRAHIM
Address : Pos 11, Jalan Mahmood Benting
Parit Jawa 84150 Muar,
Johor.
Mobile No.
Email
:
:
+60137628869
muhamadsyawal.eng@gmail.com
To seek the challenging position working environment to fully utilize my analytical, technical,
organization and interpersonal skills. My career objective is to handle some big project in this
company and to get some experience. I also interest and eager to learn about the welding and
inspection to succeed in the field of welding inspection.
OBJECTIVE
PERSONAL PARTICULARS
Age : 26 years Date of Birth : 27 April 1990
Nationality : Malaysia Gender : Male
Marital Status : Married IC No. : 900427-01-6727
Permanent
Residence
: Johor
EDUCATION BACKGROUND
1 January 2017 –
1 January 2019
 AUTHORISED ENTRANT AND STANDBY PERSON FOR
CONFINED SPACE (AESP)
1 March 2016 – 1
March 2019
 OGSP LEVEL 1
2012
(2 APRIL – 29
JUN)
Johor Skill Development Center (PUSPATRI)
 PCN NO : 315087
 PCN Welding Inspection Level ll (exp.date:24/02/2019)
 PCN Radiograpic Interpretation Level ll (exp.date: 17/05/2017)
 Appreciation to NDT MINDT
 Total Quality Management
 Construction Industry Development Board – CIDB
December 2009 –
December 2011 :
 Polytechnic Ibrahim Sultan
KM 10, Jalan Kong Kong, 81700 Pasir Gudang, Johor.
 Diploma Mechanical Engineering
2006 – 2007 :
 Sekolah Menengah Kebangsaan Raja Muda, Johor
 Sijil Pelajaran Malaysia
2003 – 2006 :
 Sekolah Menengah Kebangsaan Raja Muda, Johor.
 Penilaian Menengah Rendah

2. WORKING EXPERIENCES – FABRICATION AND CONSTRUCTION
1) Project : K-COTCONVERTER PEQ
Client : LOTTE CHEMICAL TITAN HOLDING SDN BHD
Company : TRANSLIFT SDN BHD
Position : QC Inspector (Piping&Mechanical)
Duration : Dec 2016 to Present
2) Project : TERENGGANU GAS TERMINAL PROJECT (TGAST)
Client : Petronas Carigali (PCSB)
Company : Whessoe Sdn Bhd
Position : QC Inspector (Piping)
Duration : August 2015 to Nov 2016
3) Project : Sabah Ammonia Urea (SAMUR) Project
Client : MHI-APEX-REKIND
Company : M10 Builders Sdn Bhd
Position : QC Inspector (Steel Structural)
Duration : Mac 2014 to Mac 2015
4) Project : Independent Deepwater Petroleum Terminal (IDPT) At Pengerang
Client : Dialog
Company : Whessoe Sdn Bhd
Position : QC Inspector (Piping)
Duration : July 2013 to February 2014
5) Project : Exxon Mobil TAPIS-R Topside
Client : Exxon Mobil Exploration and Rejuvenation
Company : Megagas (MG) Sdn Bhd
Position : QC Inspector (Piping)
Duration : January 2012 to July 2013
6) Project : B-193 Process Platform Project ONGC
Client : Velosi
Company : Jurunature Sdn Bhd
Position : QC Inspector (Piping)
Duration : October 2010 to November 2011
DUTIES AND RESPONSIBILITIES : QC/WELDING INSPECTOR
• Attend daily toolbox meeting with sub-contractors foreman, progress management
team and clients. Planning for task to be done and overcome any problems.
• Involved during material receiving and unloading. Check physical condition, quantity,
size, dimension, and material grade. Check documentation such as Mill Certificate,
Purchased Order and Delivery Order.
• Responsible for material storage, preservation and color coding. To locate appropriate
location, protection from environment and temperature control for consumables.

3. • Check piping material during receiving inspection such as dimension, material
identification, grade and quantity.
• Check welding consumable according to consumable certificate.
• Reviewed Project Specific procedures for piping, Client Specification, ITP, WPS,
NDT matrix and Piping Drawing such as ISO, P&ID, GA Drawing.
• Monitoring and witnessed for Welder Qualification Test (WQT) and Welding
Procedure Qualification Test (WPQT)
• Attended daily morning Safety Briefing, Daily Tool Box Talk and Progress Weekly
Mass Safety Briefing.
• Supervise and ensure HSE compliance throughout project execution and ensure are
executed in line with Company and Client HSE management system
• Liaise with Material Coordinator for material receiving Inspection for piping
materials such as Pipes, Fittings, Flanges, Outlets, Valves, Gasket, Stud Bolt & Nut.
Physically check any damage, size, type, condition, heat number, quantity and
dimension. Review for Purchase Order (PO), Delivery Order (DO), Material
Inspection Report (MIR), Material Inspection Deficiency Report (MIDR), Material
Mill Certificates and Test Certificates. Check the mechanical properties, chemical
contents and all description are complying with specs and code requirement.
• To ensure all CRA materials (Stainless steel, Cooper Nickel, Duplex Stainless Steel &
Super Duplex Stainless Steel) has been applied VCI ( Vapour Corrosion Inhibitor) for
preservation & protection, and proper handling, storage, segregate to location for
fabrication.
• Ensured welding consumables proposed for use on construction shall be qualified for
use in accordance with the applicable WPS and specification requirement
• Monitoring the backing and holding temperature of welding electrode oven, check the
consumable in term the size, type and condition and monitoring welding consumables
issuing & returning records.
• Liaise with QA/QC Coordinator, QA/QC Piping Lead, and Piping Engineer to discuss
and confirmed for any Technical and Engineering queries was found at site to be
rectify and implement at site as per discussion.
• Performed the Material Verification Inspection such as verified material type & grade,
size, dimension, heat number, piece mark number as per MAC number and IFF
Drawing.
• Performed the Fit-up Inspection to checked and ensured that the joint preparation,
root gap / face,hi-lo, bevel angle, orientation, squareness, alignment is within
tolerance as follow as per IFF Drawing, WPS and Client specification requirement.
Sketch the detail of line pipe spools for red line mark up for any additional,
modification and drawing revised.
• Monitoring before, during and after welding activities, checked the inter pass
temperature, inter pass cleaning, welding parameter checked, Oxygen level and
Ferrite count monitoring for CRA materials, welding sequence and distortion control,
and to ensured welding activities has been carried out as follow as per WPS, and to
ensured joints for CRA materials has been applied acid pickling for cleaning prior
Visual Inspection.
• Select the joint for NDT (RT, UT, MPI, DPI, PMI) by the drawing and line system as
follow as per NDT Matrix requirement, liaise with NDT Coordinator and to confirm
that the joints need to repair and location of repair. Monitoring the repair joints as
follow as per Repair Procedure and Method of repair and carried out the Hardness
Test after repair.

4. • Liaise with PWHT Technician for witnessed of Post Weld Heat Treatment as per
Client requirement, and to check the soaking time, holding time and reviewed reports.
• Carried out inspection for pipe spool and pipe support to checked the Tagging,
Quantity Condition and to ensure the pipe spools need to blowing for internal
cleaning and proper preservation to cap off all the allowed access prior send to the
blasting and painting.
• Monitoring and liaise with PMT for all the pipe spools and pipe supports installed to
the Platform and to confirm location as per drawing.
• Prepared documents required and compilation for Test Package, such as Test Package
Index Drawing, Check Sheet, Weld Summary, Punch List and etc.
• Checked the preparation of Hydro test or Pneumatic, and Line walk prior Hydrostatic
test and raised punch list by category A,B & C and follow up with Contractor to done
the priority category A for proceed Hydrostatic Test.
• Monitoring for Hydrostatic Test and to ensure that the calibration certificates of
Temperature & Chart recorder, Chloride content was valid, and Permit to work was
display at location testing. To monitor the division of pressure during pressure up and
maintain the pressure during holding time proper recorded. Witness the Flushing and
Blowing to ensure internal cleaning and all the foreign materials and debris has been
removed.
• Carry out line checking and punch killing after Hydrostatic Test and monitor for
Reinstatement Leak Test injected the Nitrogen, snoopy check during pre-
commissioning and closed the piping check sheet.
• Preparation of documents compilation for final documents prior submit to Client.
SKILLS PROFILE
 Ability and familiar with engineering drawing PIPING ISO DRAWING, PIPING
GA DRAWING, P&ID DRAWING, STRUCTURALDRAWING, STRUCTURAL
ISO DRAWING, STRUCTURAL GA DRAWING.
 Proficient in Microsoft Office 2007/2010, Microsoft Excel Worksheet, Microsoft
Power Point, Auto Cade.
 Good interpersonal skill and experience in communicating with organization or
people.

5. REFEREES
En. Irman Hadi Bin Dzulkafli
Project Manager
M10 Builders Sdn Bhd
Tel : 019-2886052
Mr. Lim Hoo Hong
Project Manager
Whessoe Sdn Bhd
Tel : 012-3967660
Mr. Voon Wooi Seong
Project Manager
Jurunature Sdn Bhd
Tel : 016-6500901
Nizaha Ashari
Trainer
Malaysian Institute of Non-Destructive
Testing (MINDT)
No.18, Jalan Tanjung SD13/2,
Bandar Sri Damansara,
52200 Kuala Lumpur.
Tel: +603-62803448 / 019-
9113077mcja79@yahoo.com
En.Afez Bin Ahmad
En.Jumaat Bin Hashim
Lecturer of Mechanical.
Politeknik Ibrahim Sultan (PSI)
(KM 10, Jin Kong Kong, 81700 Pasir
Gudang, Johor)
Tel: 07-2612488 / 07-2611070 / 07-2612060