Presentation transformer and control room thermal power plant jhalawar
•Download as PPTX, PDF•
0 likes•32 views
This document provides a summary of Vishal Sen's training seminar visit to the Kalisindh Thermal Power Project (KaTPP) in Jhalawar, Rajasthan, India. It introduces KaTPP as a 1200MW coal-based power plant located near the Kali Sindh river. The summary describes some of the key components seen on the tour including the Rankine cycle layout, transformers (generator, unit, auxiliary, service), isolated phase bus, and control room panels for monitoring functions like turbine control, fuel control, steam & water control, and generator control.
Report
Share
Report
Share
Recommended
FEROZE GANDHI UNCHAHAR THERMAL POWER PLANT(NTPC UNCHAHAR) SUMMER TRAINING
This document provides an overview of the vocational training program at the NTPC Unchahar thermal power plant in Raebareli, India. It discusses the plant's operations, including its main departments like the coal handling plant, boiler, turbines, generator, condenser, cooling tower, and ash handling plant. It also describes the sources of coal and water, and lists some advantages and disadvantages of thermal power plants. The presentation was given by Om Prakash, an electrical engineering student, under the guidance of his professor Nitish Kumar Yadav.
various types of transformers.
This document summarizes the different types of transformers used in a 210MW thermal power plant. It describes the generator transformer, station transformer, unit auxiliary transformer, rectifier transformer, instrument transformer, distribution transformer, neutral grounding transformer, and maintenance practices for transformers. The generator transformer steps up voltage from 15.75kV to 400kV, while the station transformer and unit auxiliary transformer step down voltages for power distribution. Instrument transformers are used for metering and protection.
tps 180150109049 180150109078.pptx
This document provides an overview of the components and basic workings of a thermal power station located near Jamnagar, India. It has four units with a total installed capacity of 740 MW. The key components discussed include the coal yard, coal crusher, boiler, steam turbine, condenser, generator, cooling tower, and switchyard. The boiler uses pulverized coal to generate high pressure steam, which powers the steam turbine and generator, producing electricity.
IPGCL/PPCL Training presentation
This document provides an overview of a combined cycle power plant, including its components and operations. It discusses the gas turbine generator, heat recovery steam generator (HRSG), water treatment plant, generator, transformer, switchyard, and specifications of equipment. The plant uses natural gas to power gas turbine generators and an HRSG to produce steam for a steam turbine, maximizing efficiency through heat recovery.
Vocational trainning presentation at ESSAR Power Salaya (Electrical Engineering)
- The document provides an overview of the major components of the Essar Power Salaya thermal power plant located in India, including its boiler, turbine generator, transformer yard, and switchyard.
- The plant has a capacity of 1200 MW generated from a subcritical boiler that converts water into high pressure steam. This steam powers a steam turbine connected to an electrical generator.
- The transformer yard contains equipment like circuit breakers, transformers, and bus ducts that help manage the distribution of electricity produced at different voltage levels within the plant.
industrialsummertrainingon220kvsubstationppt-170413134021.pdf
This document provides an overview of the 220/132 KV substation in Barahuwa, India. It includes a single line diagram showing the incoming and outgoing sections. The substation has three main parts: the panel section containing control and relay panels, the yard section with 220 KV, 132 KV and 33 KV sections, and the battery room powering the station. It describes the various components used in the substation like transformers, circuit breakers, isolators etc. The training at this substation helped broaden the author's knowledge of power transmission and distribution.
Industrial summer training on 220 kv substation ppt
This document provides an overview of a 220/132 kV substation in Barahuwa, India. It includes a single line diagram showing the incoming and outgoing sections. The substation has three main parts: a panel section containing control and relay panels, a yard section with 220 kV, 132 kV and 33 kV sections, and a battery room powering the station. It describes the various components used in the substation like transformers, circuit breakers, isolators etc. The training program helped broaden the author's knowledge of power transmission and distribution.
Recommended
FEROZE GANDHI UNCHAHAR THERMAL POWER PLANT(NTPC UNCHAHAR) SUMMER TRAINING
This document provides an overview of the vocational training program at the NTPC Unchahar thermal power plant in Raebareli, India. It discusses the plant's operations, including its main departments like the coal handling plant, boiler, turbines, generator, condenser, cooling tower, and ash handling plant. It also describes the sources of coal and water, and lists some advantages and disadvantages of thermal power plants. The presentation was given by Om Prakash, an electrical engineering student, under the guidance of his professor Nitish Kumar Yadav.
various types of transformers.
This document summarizes the different types of transformers used in a 210MW thermal power plant. It describes the generator transformer, station transformer, unit auxiliary transformer, rectifier transformer, instrument transformer, distribution transformer, neutral grounding transformer, and maintenance practices for transformers. The generator transformer steps up voltage from 15.75kV to 400kV, while the station transformer and unit auxiliary transformer step down voltages for power distribution. Instrument transformers are used for metering and protection.
tps 180150109049 180150109078.pptx
This document provides an overview of the components and basic workings of a thermal power station located near Jamnagar, India. It has four units with a total installed capacity of 740 MW. The key components discussed include the coal yard, coal crusher, boiler, steam turbine, condenser, generator, cooling tower, and switchyard. The boiler uses pulverized coal to generate high pressure steam, which powers the steam turbine and generator, producing electricity.
IPGCL/PPCL Training presentation
This document provides an overview of a combined cycle power plant, including its components and operations. It discusses the gas turbine generator, heat recovery steam generator (HRSG), water treatment plant, generator, transformer, switchyard, and specifications of equipment. The plant uses natural gas to power gas turbine generators and an HRSG to produce steam for a steam turbine, maximizing efficiency through heat recovery.
Vocational trainning presentation at ESSAR Power Salaya (Electrical Engineering)
- The document provides an overview of the major components of the Essar Power Salaya thermal power plant located in India, including its boiler, turbine generator, transformer yard, and switchyard.
- The plant has a capacity of 1200 MW generated from a subcritical boiler that converts water into high pressure steam. This steam powers a steam turbine connected to an electrical generator.
- The transformer yard contains equipment like circuit breakers, transformers, and bus ducts that help manage the distribution of electricity produced at different voltage levels within the plant.
industrialsummertrainingon220kvsubstationppt-170413134021.pdf
This document provides an overview of the 220/132 KV substation in Barahuwa, India. It includes a single line diagram showing the incoming and outgoing sections. The substation has three main parts: the panel section containing control and relay panels, the yard section with 220 KV, 132 KV and 33 KV sections, and the battery room powering the station. It describes the various components used in the substation like transformers, circuit breakers, isolators etc. The training at this substation helped broaden the author's knowledge of power transmission and distribution.
Industrial summer training on 220 kv substation ppt
This document provides an overview of a 220/132 kV substation in Barahuwa, India. It includes a single line diagram showing the incoming and outgoing sections. The substation has three main parts: a panel section containing control and relay panels, a yard section with 220 kV, 132 kV and 33 kV sections, and a battery room powering the station. It describes the various components used in the substation like transformers, circuit breakers, isolators etc. The training program helped broaden the author's knowledge of power transmission and distribution.
GSECL Electrical branch Training Report
The document is a training report from GSECL Gandhinagar Thermal Power Station. It provides information about the power plant and describes the key departments involved in electrical maintenance and operation - Switchyard, CPEM (coal plant electrical maintenance), and EMD (electrical maintenance department).
It summarizes the functions of the switchyard including equipment like transformers, circuit breakers, buses. It also describes the coal handling process from receiving at the plant to crushing and pulverization.
The report outlines maintenance practices and schedules for various electrical equipment like batteries, lightening arrestors, cables to ensure safe and reliable operations.
Internship PPT final.pptx on ukai thermal power station
The document summarizes a two-week internship at the Ukai Thermal Power Station (UTPS) in Gujarat, India. UTPS has an installed capacity of 1110 MW across six stages of power generation. The summary describes the key components and processes of the power plant, including coal handling, boiler and steam turbine systems, electricity generation via generators, transmission of power via switchyards, and ash handling facilities. The internship provided exposure to the various sections of the thermal power generation process.
Internship PPT ukai thermal power station .pptx
Jsjjjsnsnsnsnsnsnsnsnsnmsnnnsñsnnnsjsjssnnsnsnsnsnsnnsnsnsnsnssnsnsnsnsnsnnsnsnsnsnsnsnsnsjnssnsjsjsjjsnnejsnenenejn
Internship PPT final ukai thermal power station
The document summarizes a two-week internship at the Ukai Thermal Power Station (UTPS) in Gujarat, India. UTPS has an installed capacity of 1110 MW across six stages of power generation. The summary describes the key components and processes of the power plant, including coal handling, boiler and steam turbine systems, electricity generation via generators, transmission of power via switchyards, and ash handling facilities. The internship provided exposure to the various sections of the thermal power generation process.
Vocational training in ntpc rihandnagar
This ppt is for electrical engineering student focusing on electrical machinery of power plant .made by neeraj kumar vishwakarma
220kv gss pindwara(sirohi)
This document summarizes a seminar presented on practical training at a 220kV substation. It includes an introduction to the substation and descriptions of its key components like transformers, circuit breakers, current transformers, lightning arrestors, capacitors and the control room. Diagrams of the substation's single line diagram are also included. The conclusion states that the training provided insight into real instrumentation used at substations and how they are operated and managed.
National Hydro Power Plant collage PPT 1.pptx
The document discusses the Teesta Low Dam-IV hydroelectric power plant located in West Bengal, India. It generates 160MW of power through four 40MW turbine generators using the kinetic energy of the Teesta River's flowing water. Water is collected and channeled through penstocks to drive Kaplan turbines connected to generators, which produce electricity then stepped up to 224kV for transmission via a switchyard. The power plant utilizes the river's flow between an upper reservoir level of 182.25m and lower level of 179m to generate power in an environmentally sustainable run-of-the-river scheme.
ntpc ppt
The document summarizes the 4 week industrial training that the author completed at NTPC Limited Badarpur Thermal Power Station from June 3rd to July 4th, 2013. The training involved visiting various divisions of the power plant including the Electrical Maintenance Department I (EMD-I), Electrical Maintenance Department II (EMD-II), and Control and Instrumentation Department (C&I). The document then provides details on the basic process of electricity generation from coal, the major components of a power plant, electrical equipment, and laboratories in the Control and Instrumentation Department.
Bangladesh Power Stations & Power Plants Overview
It is a presentation about Bangladesh power stations and power plants such as: Energypac Engineering Ltd, DESCO,Dockyard & Engineering Works LTD ,RPCL, APSCL.
Trainingreport 132 KV
This document provides a training report on a 132/33 kV substation in Uttar Pradesh, India. It discusses key components of the substation including transformers, types of substations, earthing methodology, and equipment. The substation receives power from a 132 kV grid, uses transformers to step down the voltage to 33 kV, and has feeders distributing power to the local area. Key elements covered include transformer specifications, types of circuit breakers, relay equipment, and the importance of proper earthing and bonding systems for safety and equipment protection.
Ramendra summer training presentation
This document provides an overview of several power plants in Delhi, India including their specifications and components. It discusses the working of gas power plants which use gas turbines and heat recovery steam generators. It also describes the water treatment plant, generators, transformers, switchyard components like circuit breakers and insulators. The specifications of various equipment are listed. Finally, it discusses the merits and demerits of gas turbine and steam power plants.
Heavy water plant and there electrical systam
The Heavy Water Plant in Kota, Rajasthan is India's first indigenous heavy water plant based on the girdler sulphide process. It was commissioned in 1982 with a capacity to produce 85 metric tons of heavy water annually. The plant uses electricity supplied by the nearby Rajasthan Atomic Power Station and has a complex electrical system including transformers, circuit breakers, and other equipment to distribute power within the plant. Heavy water is used as a moderator and coolant in nuclear reactors for power generation.
Mppkvv company ltd
The document discusses the training provided by MPPKVV Company Ltd, which is divided into four sections over various days: transformer repairing, low transmission meter testing, high transmission meter testing, and 33/11 KV substation. It provides details on each section, including an overview of transformer components, reasons for transformer failure, pre-commissioning transformer tests, and the setup and functioning of a 33/11 KV substation.
Htps
The document provides an overview of a thermal power plant, including its key components and operations. It discusses the introduction and breakdown of India's power sources. The main parts of a thermal power plant are described, such as the coal handling plant, boiler, turbine, condenser, and cooling towers. Diagrams illustrate the steam generation and electricity production processes. Site selection factors for thermal power plants include transportation access, geology, topography, water resources, and proximity to population centers.
fdocuments.in_presentation-on-substation-220-kv.pptx
The document provides information about the Ablowal substation located in Sarabha Nagar, India. It discusses the key equipment used in the substation including transformers, circuit breakers, isolators, lightning arresters, and capacitor banks. It explains the advantages of high voltage transmission and describes the types of substations. The document also covers availability tariff, unscheduled interchange rates, and the expectations from central generating stations to provide accurate availability forecasts.
Transformers
This document summarizes a seminar presentation on different types of transformers used in a 210MW thermal power plant. It describes 7 main types of transformers used: generator transformer, station transformer, distribution transformer, unit auxiliary transformer, instrument transformer, rectifier transformer, and neutral ground transformer. For each type, it provides key specifications like voltage ratings, cooling type, and functions. The document also covers transformer components, working principle, cooling systems, and maintenance.
Rps plant
This document summarizes Hemant Shrivastava's practical training at the Rana Pratap Sagar Hydroelectric Power Station. It includes an introduction to the power station, describing its location on the Chambal River and its 4 generating units of 43MW each. The document then provides details on the classification and components of the power station, including its feeders, turbines, generators, transformers and PLCC communication system. It concludes with advantages like low maintenance costs, and disadvantages such as high capital costs and potential impacts of dry seasons or reservoir problems.
PRESENTATION ON UPPTCL 220 KV TRANSMISSION SUMMER TRAINING BANDA, BANDA FROM ...
220/132/33 KV SUMMER TRAINING TRANSMISSION SUB-STATION BANDA.
Summer training ppt about transmission sub-station from (upptcl).
Avdhehs kumar presention kstps kota
Kota Super Thermal Power Station (KSTPS) is a coal-based power plant located in Rajasthan, India. It has a total installed capacity of 1240 MW generated across 7 units. The plant receives coal via train from nearby mines and uses water from the Chambal River. It employs a Rankine cycle with a coal handling plant, ash handling plant, electrostatic precipitators, turbo generators to produce power, and a cooling system using hydrogen. Transformers are used to step up the voltage from the generators to connect to the grid.
A summer training presentation on national thermal power
This document provides an overview of a summer training presentation on the National Thermal Power Plant in Kahalgaon, Bihar, India. It discusses the key components and processes of a coal power plant, including: how coal is handled and burned to create steam; how the steam powers turbines which spin generators to produce electricity; and the roles of auxiliary equipment like transformers. The content is organized by the major sections of a thermal power plant and includes diagrams to illustrate key components like boilers, turbines, generators and transformers.
More Related Content
Similar to Presentation transformer and control room thermal power plant jhalawar
GSECL Electrical branch Training Report
The document is a training report from GSECL Gandhinagar Thermal Power Station. It provides information about the power plant and describes the key departments involved in electrical maintenance and operation - Switchyard, CPEM (coal plant electrical maintenance), and EMD (electrical maintenance department).
It summarizes the functions of the switchyard including equipment like transformers, circuit breakers, buses. It also describes the coal handling process from receiving at the plant to crushing and pulverization.
The report outlines maintenance practices and schedules for various electrical equipment like batteries, lightening arrestors, cables to ensure safe and reliable operations.
Internship PPT final.pptx on ukai thermal power station
The document summarizes a two-week internship at the Ukai Thermal Power Station (UTPS) in Gujarat, India. UTPS has an installed capacity of 1110 MW across six stages of power generation. The summary describes the key components and processes of the power plant, including coal handling, boiler and steam turbine systems, electricity generation via generators, transmission of power via switchyards, and ash handling facilities. The internship provided exposure to the various sections of the thermal power generation process.
Internship PPT ukai thermal power station .pptx
Jsjjjsnsnsnsnsnsnsnsnsnmsnnnsñsnnnsjsjssnnsnsnsnsnsnnsnsnsnsnssnsnsnsnsnsnnsnsnsnsnsnsnsnsjnssnsjsjsjjsnnejsnenenejn
Internship PPT final ukai thermal power station
The document summarizes a two-week internship at the Ukai Thermal Power Station (UTPS) in Gujarat, India. UTPS has an installed capacity of 1110 MW across six stages of power generation. The summary describes the key components and processes of the power plant, including coal handling, boiler and steam turbine systems, electricity generation via generators, transmission of power via switchyards, and ash handling facilities. The internship provided exposure to the various sections of the thermal power generation process.
Vocational training in ntpc rihandnagar
This ppt is for electrical engineering student focusing on electrical machinery of power plant .made by neeraj kumar vishwakarma
220kv gss pindwara(sirohi)
This document summarizes a seminar presented on practical training at a 220kV substation. It includes an introduction to the substation and descriptions of its key components like transformers, circuit breakers, current transformers, lightning arrestors, capacitors and the control room. Diagrams of the substation's single line diagram are also included. The conclusion states that the training provided insight into real instrumentation used at substations and how they are operated and managed.
National Hydro Power Plant collage PPT 1.pptx
The document discusses the Teesta Low Dam-IV hydroelectric power plant located in West Bengal, India. It generates 160MW of power through four 40MW turbine generators using the kinetic energy of the Teesta River's flowing water. Water is collected and channeled through penstocks to drive Kaplan turbines connected to generators, which produce electricity then stepped up to 224kV for transmission via a switchyard. The power plant utilizes the river's flow between an upper reservoir level of 182.25m and lower level of 179m to generate power in an environmentally sustainable run-of-the-river scheme.
ntpc ppt
The document summarizes the 4 week industrial training that the author completed at NTPC Limited Badarpur Thermal Power Station from June 3rd to July 4th, 2013. The training involved visiting various divisions of the power plant including the Electrical Maintenance Department I (EMD-I), Electrical Maintenance Department II (EMD-II), and Control and Instrumentation Department (C&I). The document then provides details on the basic process of electricity generation from coal, the major components of a power plant, electrical equipment, and laboratories in the Control and Instrumentation Department.
Bangladesh Power Stations & Power Plants Overview
It is a presentation about Bangladesh power stations and power plants such as: Energypac Engineering Ltd, DESCO,Dockyard & Engineering Works LTD ,RPCL, APSCL.
Trainingreport 132 KV
This document provides a training report on a 132/33 kV substation in Uttar Pradesh, India. It discusses key components of the substation including transformers, types of substations, earthing methodology, and equipment. The substation receives power from a 132 kV grid, uses transformers to step down the voltage to 33 kV, and has feeders distributing power to the local area. Key elements covered include transformer specifications, types of circuit breakers, relay equipment, and the importance of proper earthing and bonding systems for safety and equipment protection.
Ramendra summer training presentation
This document provides an overview of several power plants in Delhi, India including their specifications and components. It discusses the working of gas power plants which use gas turbines and heat recovery steam generators. It also describes the water treatment plant, generators, transformers, switchyard components like circuit breakers and insulators. The specifications of various equipment are listed. Finally, it discusses the merits and demerits of gas turbine and steam power plants.
Heavy water plant and there electrical systam
The Heavy Water Plant in Kota, Rajasthan is India's first indigenous heavy water plant based on the girdler sulphide process. It was commissioned in 1982 with a capacity to produce 85 metric tons of heavy water annually. The plant uses electricity supplied by the nearby Rajasthan Atomic Power Station and has a complex electrical system including transformers, circuit breakers, and other equipment to distribute power within the plant. Heavy water is used as a moderator and coolant in nuclear reactors for power generation.
Mppkvv company ltd
The document discusses the training provided by MPPKVV Company Ltd, which is divided into four sections over various days: transformer repairing, low transmission meter testing, high transmission meter testing, and 33/11 KV substation. It provides details on each section, including an overview of transformer components, reasons for transformer failure, pre-commissioning transformer tests, and the setup and functioning of a 33/11 KV substation.
Htps
The document provides an overview of a thermal power plant, including its key components and operations. It discusses the introduction and breakdown of India's power sources. The main parts of a thermal power plant are described, such as the coal handling plant, boiler, turbine, condenser, and cooling towers. Diagrams illustrate the steam generation and electricity production processes. Site selection factors for thermal power plants include transportation access, geology, topography, water resources, and proximity to population centers.
fdocuments.in_presentation-on-substation-220-kv.pptx
The document provides information about the Ablowal substation located in Sarabha Nagar, India. It discusses the key equipment used in the substation including transformers, circuit breakers, isolators, lightning arresters, and capacitor banks. It explains the advantages of high voltage transmission and describes the types of substations. The document also covers availability tariff, unscheduled interchange rates, and the expectations from central generating stations to provide accurate availability forecasts.
Transformers
This document summarizes a seminar presentation on different types of transformers used in a 210MW thermal power plant. It describes 7 main types of transformers used: generator transformer, station transformer, distribution transformer, unit auxiliary transformer, instrument transformer, rectifier transformer, and neutral ground transformer. For each type, it provides key specifications like voltage ratings, cooling type, and functions. The document also covers transformer components, working principle, cooling systems, and maintenance.
Rps plant
This document summarizes Hemant Shrivastava's practical training at the Rana Pratap Sagar Hydroelectric Power Station. It includes an introduction to the power station, describing its location on the Chambal River and its 4 generating units of 43MW each. The document then provides details on the classification and components of the power station, including its feeders, turbines, generators, transformers and PLCC communication system. It concludes with advantages like low maintenance costs, and disadvantages such as high capital costs and potential impacts of dry seasons or reservoir problems.
PRESENTATION ON UPPTCL 220 KV TRANSMISSION SUMMER TRAINING BANDA, BANDA FROM ...
220/132/33 KV SUMMER TRAINING TRANSMISSION SUB-STATION BANDA.
Summer training ppt about transmission sub-station from (upptcl).
Avdhehs kumar presention kstps kota
Kota Super Thermal Power Station (KSTPS) is a coal-based power plant located in Rajasthan, India. It has a total installed capacity of 1240 MW generated across 7 units. The plant receives coal via train from nearby mines and uses water from the Chambal River. It employs a Rankine cycle with a coal handling plant, ash handling plant, electrostatic precipitators, turbo generators to produce power, and a cooling system using hydrogen. Transformers are used to step up the voltage from the generators to connect to the grid.
A summer training presentation on national thermal power
This document provides an overview of a summer training presentation on the National Thermal Power Plant in Kahalgaon, Bihar, India. It discusses the key components and processes of a coal power plant, including: how coal is handled and burned to create steam; how the steam powers turbines which spin generators to produce electricity; and the roles of auxiliary equipment like transformers. The content is organized by the major sections of a thermal power plant and includes diagrams to illustrate key components like boilers, turbines, generators and transformers.
Similar to Presentation transformer and control room thermal power plant jhalawar (20)
Internship PPT final.pptx on ukai thermal power station
Internship PPT final.pptx on ukai thermal power station
fdocuments.in_presentation-on-substation-220-kv.pptx
fdocuments.in_presentation-on-substation-220-kv.pptx
PRESENTATION ON UPPTCL 220 KV TRANSMISSION SUMMER TRAINING BANDA, BANDA FROM ...
PRESENTATION ON UPPTCL 220 KV TRANSMISSION SUMMER TRAINING BANDA, BANDA FROM ...
A summer training presentation on national thermal power
A summer training presentation on national thermal power
Recently uploaded
Software Engineering and Project Management - Software Testing + Agile Method...
Software Testing: A Strategic Approach to Software Testing, Strategic Issues, Test Strategies for Conventional Software, Test Strategies for Object -Oriented Software, Validation Testing, System Testing, The Art of Debugging.
Agile Methodology: Before Agile – Waterfall, Agile Development.
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
Null Bangalore | Pentesters Approach to AWS IAM
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
原版制作(Humboldt毕业证书)柏林大学毕业证学位证一模一样
原件一模一样【微信：bwp0011】《(Humboldt毕业证书)柏林大学毕业证学位证》【微信：bwp0011】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问微bwp0011
【主营项目】
一.毕业证【微bwp0011】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微bwp0011】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 08 Doors and Windows.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 08 Doors and Windows
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
SCALING OF MOS CIRCUITS m .pptx
this ppt explains about scaling parameters of the mosfet it is basically vlsi subject
Gas agency management system project report.pdf
The project entitled "Gas Agency" is done to make the manual process easier by making it a computerized system for billing and maintaining stock. The Gas Agencies get the order request through phone calls or by personal from their customers and deliver the gas cylinders to their address based on their demand and previous delivery date. This process is made computerized and the customer's name, address and stock details are stored in a database. Based on this the billing for a customer is made simple and easier, since a customer order for gas can be accepted only after completing a certain period from the previous delivery. This can be calculated and billed easily through this. There are two types of delivery like domestic purpose use delivery and commercial purpose use delivery. The bill rate and capacity differs for both. This can be easily maintained and charged accordingly.
AI for Legal Research with applications, tools
AI applications in legal research include rapid document analysis, case law review, and statute interpretation. AI-powered tools can sift through vast legal databases to find relevant precedents and citations, enhancing research accuracy and speed. They assist in legal writing by drafting and proofreading documents. Predictive analytics help foresee case outcomes based on historical data, aiding in strategic decision-making. AI also automates routine tasks like contract review and due diligence, freeing up lawyers to focus on complex legal issues. These applications make legal research more efficient, cost-effective, and accessible.
一比一原版(osu毕业证书)美国俄勒冈州立大学毕业证如何办理
原版一模一样【微信：741003700 】【(osu毕业证书)美国俄勒冈州立大学毕业证成绩单】【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
办理(osu毕业证书)美国俄勒冈州立大学毕业证【微信：741003700 】外观非常简单，由纸质材料制成，上面印有校徽、校名、毕业生姓名、专业等信息。
办理(osu毕业证书)美国俄勒冈州立大学毕业证【微信：741003700 】格式相对统一，各专业都有相应的模板。通常包括以下部分：
校徽：象征着学校的荣誉和传承。
校名:学校英文全称
授予学位：本部分将注明获得的具体学位名称。
毕业生姓名：这是最重要的信息之一，标志着该证书是由特定人员获得的。
颁发日期：这是毕业正式生效的时间，也代表着毕业生学业的结束。
其他信息：根据不同的专业和学位，可能会有一些特定的信息或章节。
办理(osu毕业证书)美国俄勒冈州立大学毕业证【微信：741003700 】价值很高，需要妥善保管。一般来说，应放置在安全、干燥、防潮的地方，避免长时间暴露在阳光下。如需使用，最好使用复印件而不是原件，以免丢失。
综上所述，办理(osu毕业证书)美国俄勒冈州立大学毕业证【微信：741003700 】是证明身份和学历的高价值文件。外观简单庄重，格式统一，包括重要的个人信息和发布日期。对持有人来说，妥善保管是非常重要的。
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
Slides for the 4th Presentation on LLM Fine-Tuning with QLoRA Presented by Anant, featuring DataStax Astra
Recently uploaded (20)
Software Engineering and Project Management - Software Testing + Agile Method...
Software Engineering and Project Management - Software Testing + Agile Method...
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 08 Doors and Windows.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 08 Doors and Windows.pdf
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
1FIDIC-CONSTRUCTION-CONTRACT-2ND-ED-2017-RED-BOOK.pdf
1FIDIC-CONSTRUCTION-CONTRACT-2ND-ED-2017-RED-BOOK.pdf
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
Presentation transformer and control room thermal power plant jhalawar
- 1. SUBMITTED BY:- VISHAL SEN ELECTRICAL ENGINEERING 7TH SEM(4TH YEAR) 2020------ SUBMITTED TO:- Name of teacher / professor TRAINING SEMINAR OF “KALISINDH POWER PROJECT” GOVERNMENT ENGINEERING COLLEGE, JHALAWAR
- 2. CERTIFFET
- 3. KALISINDH THERMAL POWER PROJECT, JHALAWAR
- 4. CONTENT • INTRODUCTION OF “KaTPP” • OVERVIEW OF THE THARMAL POWER PLANT • TRANSFORMER • CONTROL ROOM
- 5. INTRODUCTION OF “KTPP” • Ka.T.P.P is a coal based power plant in rajasthan. • It is located in Nimoda village,near Kali Sindh river. • It has two unites each of 600MW capacity. • TOTAL GENRATION CAPACITY=1200MW.
- 6. OVERVIEW
- 8. TRANSFORMER Basic Principle of Transformer
- 9. PART OF TRANSFORME R • Transformer is made of following components:- • CORE • WINDING • TANK • BUSHING • AUXILIARY EQUIPMENT • INSULATING OIL • COOLING SYSTEM • Conservator • Breather • Explosion vent
- 10. TYPES OF TRANSFORMER In kalisindh, there are various transformers for various purpose. They are :- • Generator transformer (GT) • Unite transformer (UT) • Unit auxiliary transformer (UAT) • Unit service transformer (UST) • Unit station transformer • Natural grounding transformer(NGT) INSTRUMENT TRANSFORMERS • Current transformer (CT) • Potential transformer (PT)
- 11. GENERATOR TRANSFORMER (GT) • Output of generator has step up 22KV to 400KV by generating transformer. • In Kalisindh power plant 150/ 200/ 250MVA, 22.98/22KV, generating transformers are used. • There is a transformer of 588 MVA capacity. • Usally these transformer are outdoor types
- 13. UNIT TRANSFORMER (UT) • Unit transformer are installed to fed supply to HT switchgear • There are two 80KVA transformer installed near GT. • Electricity is supplied to BDF, CWP, ID, FD, PA, FANS from Unite Transformer. • The unit transformer is used to HT switchgear and it supplies voltage 22/11KV to UTA and different motors in boiler. • unit transformer is rated for 48/64/80MVA, 22/11.6KVA, 11dyn11yn type of winding. • This permit to voltage down up to 11KV it have two radiator.
- 14. UNITE SERVICE TRANSFORMER (UST) • It is also a 66KV/415V transformers which is used to supply the auxiliaries connected to the unit secondary switchgear bus. • Step-dwon transformer
- 15. UNIT AUXILIARY TRANSFORMER (UAT) • UAT is connected between the generator and the Generator Transformer. • It is step dwon transformer, which steps down the voltage from 16.5KV to 6.9KV .
- 16. UNIT STATION TRANSFORMER • It is a step down transformer, whitch is connected to the station bus. • It steps down the voltage from 6.6KV to 0.433KV.
- 18. CONTROL ROOM PENAL FAN CONTROL • Primary Air Fan • Furnace pressure • Forced draft fan • Induced draft fan TURBINE CONTROL • Pressure Control • Load Control • Speed Control FUEL CONTROL • Coal, Oil flow • Oil pressure • Flow of Air STEAM & WATER CONTROL • Drum level control • Flow of water & steam • Pressure of steam and water • Temp. of steam and water GENERATOR CONTROL • Stator Rotor temp. • For stator cooling a) H2 pressure b) H2O pressure
- 20. SATATION LOAD IN KATPP
- 21. AIR AND FUEL GASS SYSTEM
- 22. MILLS OVERVIEW
- 23. PA FAN SYSTEM