* Criteria of higher winter production versus annual production maximization
* Hybrid systems.
* Storage Systems.
* Types of Batteries.
* The importance of energy efficiency in consumption in the isolated systems.
* Maintenance.
• Solar resource assessment
• Determination of profitability of a PV plant
• Selection and optimization of the site.
• Selection of components (Inverters, Modules, Protection and Wiring, Grounding, Transformers, Metering, Grid Connection)
• Advanced calculations : Estimated losses; Shading study, etc
• Electrical diagrams
For direct download link, visit:
http://solarreference.com/what-you-need-to-design-rural-mini-grids/
The “Mini Grid Design Manual” would be useful to anyone wanting to design generation-to-house wiring systems for simple village level grids. With detailed theory as well as practical advice, it is very much relevant today as it was when published back in 2000.
• Solar resource assessment
• Determination of profitability of a PV plant
• Selection and optimization of the site.
• Selection of components (Inverters, Modules, Protection and Wiring, Grounding, Transformers, Metering, Grid Connection)
• Advanced calculations : Estimated losses; Shading study, etc
• Electrical diagrams
For direct download link, visit:
http://solarreference.com/what-you-need-to-design-rural-mini-grids/
The “Mini Grid Design Manual” would be useful to anyone wanting to design generation-to-house wiring systems for simple village level grids. With detailed theory as well as practical advice, it is very much relevant today as it was when published back in 2000.
An Overview of Photovoltaic Systems or PV Systems. This PPT outlines what a solar systems is and what it is consisted of. From solar panels to charge controller to deep cycle batteries to the inverter.
Design & estimation of rooftop grid tied solar pv systemSabrina Chowdhury
Energy plays a pivotal role in our daily activities. The degree of development and civilization of a country is measured by the amount of utilization of energy by human beings. Energy demand is increasing day by day due to increase in population,
urbanization and industrialization. The world’s fossil fuel supply viz. coal, petroleum and natural gas will thus be depleted in a few hundred years. The rate of energy consumption increasing, supply is depleting resulting in inflation and energy shortage. This is called energy crisis. Hence alternative or renewable sources of energy have to be developed to meet future energy requirement.
In this paper we study how to establish photovoltaic solar power plant Design as well as calculation of power production, base on that to further we find recommendation and techniques to optimized cost of PV solar power plant. To establishment of green and sustainable development of solar PV power plant to reduce a burden of state electricity board.
Basic introduction to solar PV System Presentation.
The need for renewable energy resources has never been bigger than today and so is a lot of research going to match this high energy demand. Solar PV Array technology is one such technique which can actually make the effective use of solar energy available to us.
Electrical and Solar PV Systems (www.solartraining.ca)Irtaza M. Syed
Overview and basics of conventional electric power distribution and solar Photo-voltaic (PV) systems. Generation, Transmission, distribution and utilization. Power flow, anti-islanding and PV systems connection to utility. PV applications and market. (www.solartraining.ca)
Designed a complete system of solar cell arrays required for a commercial complex. Researched and derived mathematical equations to install the system using given budget constraints. Made CAD drawings of the arrangement of inverter arrays required for installing the system.
Design of solar pv grid connected system based on load requirement and also a...Gururaj B Rawoor
About KPCL
Solar Department in KPCL
Working principle
Types of solar photovoltaic system
Load sheet
Calculation of load
Stand alone system
Advantages
Disadvantages
Applications
Industrial visit
Solar PV calculator
An Overview of Photovoltaic Systems or PV Systems. This PPT outlines what a solar systems is and what it is consisted of. From solar panels to charge controller to deep cycle batteries to the inverter.
Design & estimation of rooftop grid tied solar pv systemSabrina Chowdhury
Energy plays a pivotal role in our daily activities. The degree of development and civilization of a country is measured by the amount of utilization of energy by human beings. Energy demand is increasing day by day due to increase in population,
urbanization and industrialization. The world’s fossil fuel supply viz. coal, petroleum and natural gas will thus be depleted in a few hundred years. The rate of energy consumption increasing, supply is depleting resulting in inflation and energy shortage. This is called energy crisis. Hence alternative or renewable sources of energy have to be developed to meet future energy requirement.
In this paper we study how to establish photovoltaic solar power plant Design as well as calculation of power production, base on that to further we find recommendation and techniques to optimized cost of PV solar power plant. To establishment of green and sustainable development of solar PV power plant to reduce a burden of state electricity board.
Basic introduction to solar PV System Presentation.
The need for renewable energy resources has never been bigger than today and so is a lot of research going to match this high energy demand. Solar PV Array technology is one such technique which can actually make the effective use of solar energy available to us.
Electrical and Solar PV Systems (www.solartraining.ca)Irtaza M. Syed
Overview and basics of conventional electric power distribution and solar Photo-voltaic (PV) systems. Generation, Transmission, distribution and utilization. Power flow, anti-islanding and PV systems connection to utility. PV applications and market. (www.solartraining.ca)
Designed a complete system of solar cell arrays required for a commercial complex. Researched and derived mathematical equations to install the system using given budget constraints. Made CAD drawings of the arrangement of inverter arrays required for installing the system.
Design of solar pv grid connected system based on load requirement and also a...Gururaj B Rawoor
About KPCL
Solar Department in KPCL
Working principle
Types of solar photovoltaic system
Load sheet
Calculation of load
Stand alone system
Advantages
Disadvantages
Applications
Industrial visit
Solar PV calculator
10 important safety changes in 2014 necJohn Newquist
This is just some of the 2014 NEC changes that I thought affected industrial safety. Bob Lomastro suggest adding "No more grounding to neutral raceway grounding."
Photovoltaic Training - Session 3 - Plant OperationLeonardo ENERGY
Control systems and telecommunications.
Components and infrastructure needed to control systems
Monitoring and troubleshooting
Management of information obtained by the control system
Management and alarms.
Sending information for maintenance purposes.
Security of the Installation.
Fundamental characteristics required in a surveillance system.
Protection systems against theft.
Anti‐intrusion systems.
CCTV and video surveillance.
e‐Rounds.
Remote control systems.
Security in PV roofs.
Photovoltaic Training - Session 4 - Plant MaintenanceLeonardo ENERGY
Importance of good maintenance procedure in the plant operation.
•
Components to be maintained.
o
PV Panel.
o
Inverter.
o
Transformer.
o
Solar tracker.
o
Cabinet.
•
Types of maintenance
o
Corrective maintenance.
o
Preventive Maintenance.
•
Supplies.
o
Critical elements.
o
Guarantees.
•
Management of spare parts and stock.
•
Types of inspections and reach
o
Visual inspections.
o
Deep inspections.
o
Frequency of revisions.
A brief overview of PV market globally and regionally is presented and how it has disrupted the current network business model. Energy Storage has become a necessity as penetration of PV in the current network increases and created challenging ramping issues as the daily load curves have changed to what is now popularly called “Duck” curves. The value of energy storage in the network is presented, clearly demonstrating that maximum value is realised at end users, commercial and residential. Battery storage is one of the most practical option. Commercial battery technologies are presented, followed by selected case studies.
Photovoltaic Training - Session 2 - Construction and Start-UpLeonardo ENERGY
* Civil works. Preparation of infrastructure.
* Mechanical assembly.
* Electrical Installation: Ground‐mounted PV facilities. Rooftop installations. Wiring. Cabinets. Ground net.
* Environmental aspects and waste management.
* Quality. Critical aspects in the development of the installation.
* Testing. Key issues. Inverter tests. Maximum power of the PV generator. Evaluation of the Performance Ratio real.
To download head to http://solarreference.com/solar-pv-codes-brooks/
Also available on the Brook Solar website (they have some quality stuff)
This presentation from Brook Solar (Now Brooks Engineering LLC) is a wonderful compilation of the standards in place in the PV industry. But you do know that standards are like babies, they don't stop growing!
For more quality information visit http://solarreference.com/
Arturo Zarate of DECK Monitoring explains monitoring systems: How they work, what components are required, overview of installation process, how to interpret data, and benefits of.
Solving Energy Storage Challenges Offshore - Offshore Europe 2017 Cinema Seminar - Dr. David Blood, Parker Hannifin
Energy storage is big news, following the UK government’s announcement to establish a center for battery research and plans to reduce or shift electricity use to creating a smarter, more flexible energy system.
Moving rig-based diesel gen sets to a new hybrid technology might sound like a step too far. But using battery storage alongside existing power systems is not a huge leap, with the potential to reduce fuel, operations and maintenance costs, whilst improving power quality.
This technical seminar for oil and gas professionals was run by Parker at Offshore Europe 2017. It covers the potential applications and benefits of energy storage, an overview of micro-grids and how to overcome potential challenges. The presentation also features some case study examples.
Learn more: http://solutions.parker.com/OE17_Contact
Vector White paper - Understanding the difference between energy and power b...Peter Tait
Energy storage technology is rapidly evolving with various chemistries, technologies and C ratings available, selecting the right battery for the correct application can be complicated.
There are many unique advantages and disadvantages when comparing energy storage technology and chemistry and considering the C rating for the specific application requires an understanding of the functional demands to be placed on the storage system.
This white paper is a guide and uses modular, fully integrated, AC-coupled industrial energy storage system technology as an example to provide a guide across various applications and will detail how C ratings can be applied.
Please contact us if you have any questions
Supreme Power Solutions Co., Ltd. (also referred to as SPS), established in 2003, is a world-class manufacturer of ultra-capacitor products including cells, systems and technological solutions.
A new generation of instruments and tools to monitor buildings performanceLeonardo ENERGY
What is the added value of monitoring the flexibility, comfort, and well-being of a building? How can occupants be better informed about the performance of their building? And how to optimize a building's maintenance?
The slides were presented during a webinar and roundtable with a focus on a new generation of instruments and tools to monitor buildings' performance, and their link with the Smart Readiness Indicator (SRI) for buildings as introduced in the EU's Energy Performance of Buildings Directive (EPBD).
Link to the recordings: https://youtu.be/ZCFhmldvRA0
Addressing the Energy Efficiency First Principle in a National Energy and Cli...Leonardo ENERGY
When designing energy and climate policies, EU Member States have to apply the Energy Efficiency First Principle: priority should be given to measures reducing energy consumption before other decarbonization interventions are adopted. This webinar summarizes elements of the energy and climate policy of Cyprus illustrating how national authorities have addressed this principle so far, and outline challenges towards its much more rigorous implementation that is required in the coming years.
Auctions for energy efficiency and the experience of renewablesLeonardo ENERGY
Auctions are an emerging market-based policy instrument to promote energy efficiency that has started to gain traction in the EU and worldwide. This presentation provides an overview and comparison of several energy efficiency auctions and derives conclusions on the effects of design elements based on auction theory and on experiences of renewable energy auctions. We include examples from energy efficiency auctions in Brazil, Canada, Germany, Portugal, Switzerland, Taiwan, UK, and US.
A recording of this presentation can be viewed at:
https://youtu.be/aC0h4cXI9Ug
Energy efficiency first – retrofitting the building stock finalLeonardo ENERGY
Retrofitting the building stock is a challenging undertaking in many respects - including costs. Can it nevertheless qualify as a measure under the Energy Efficiency First principle? Which methods can be applied for the assessment and what are the results in terms of the cost-effectiveness of retrofitting the entire residential building stock? How do the results differ for minimization of energy use, CO2 emissions and costs? And which policy conclusions can be drawn?
This presentation was used during the 18th webinar in the Odyssee-Mure on Energy Efficiency Academy on February 3, 2022.
A link to the recording: https://youtu.be/4pw_9hpA_64
How auction design affects the financing of renewable energy projects Leonardo ENERGY
Recording available at https://youtu.be/lPT1o735kOk
Renewable energy auctions might affect the financing of renewable energy (RE) projects. This webinar presents the results of the AURES II project exploring this topic. It discusses how auction designs ranging from bid bonds to penalties and remuneration schemes impact financing and discusses creating a low-risk auction support framework.
This presentation discusses the contribution of Energy Efficiency Funds to the financing of energy efficiency in Europe. The analysis is based on the MURE database on energy efficiency policies. As an example, the German Energy Efficiency Fund is described in more detail.
This is the 17th webinar in the Odyssee-Mure on Energy Efficiency Academy.
Recordings are available on: https://youtu.be/KIewOQCgQWQ
(see updated version of this presentation:
https://www.slideshare.net/sustenergy/energy-efficiency-funds-in-europe-updated)
The Energy Efficiency First Principle is a key pillar of the European Green Deal. A prerequisite for its widespread application is to secure financing for energy efficiency investments.
This presentation discusses the contribution of Energy Efficiency Funds to the financing of energy efficiency in Europe. The analysis is based on the MURE database on energy efficiency policies. As an example, the German Energy Efficiency Fund is described in more detail.
This is the 17th webinar in the Odyssee-Mure on Energy Efficiency Academy.
Recordings are available on: https://youtu.be/KIewOQCgQWQ
Five actions fit for 55: streamlining energy savings calculationsLeonardo ENERGY
During the first year of the H2020 project streamSAVE, multiple activities were organized to support countries in developing savings estimations under Art.3 and Art.7 of the Energy Efficiency Directive (EED).
A fascinating output of the project so far is the “Guidance on Standardized saving methodologies (energy, CO2 and costs)” for a first round of five so-called Priority Actions. This Guidance will assist EU member states in more accurately calculating savings for a set of new energy efficiency actions.
This webinar presents this Guidance and other project findings to the broader community, including industry and markets.
AGENDA
14:00 Introduction to streamSAVE
(Nele Renders, Project Coordinator)
14:10 Views from the EU Commission and the link with Fit-for-55 (Anne-Katherina Weidenbach, DG ENER)
14:20 The streamSAVE guidance and its platform illustrated (Elisabeth Böck, AEA)
14:55 A view from industry: What is the added value of streamSAVE (standardized) methods in frame of the EED (Conor Molloy, AEMS ECOfleet)
14:55 Country experiences: the added value of standardized methods (Elena Allegrini, ENEA, Italy)
The recordings of the webinar can be found on https://youtu.be/eUht10cUK1o
This webinar analyses energy efficiency trends in the EU for the period 2014-2019 and the impact of COVID-19 in 2020 (based on estimates from Enerdata).
The speakers present the overall trend in total energy supply and in final energy consumption, as well as details by sector, alongside macro-economic data. They will explain the main drivers of the variation in energy consumption since 2014 and determine the impact of energy savings.
Speakers:
Laura Sudries, Senior Energy Efficiency Analyst, Enerdata
Bruno Lapillonne, Scientific Director, Enerdata
The recordings of the presentation (webinar) can be viewed at:
https://youtu.be/8RuK5MroTxk
Energy and mobility poverty: Will the Social Climate Fund be enough to delive...Leonardo ENERGY
Prior to the current soaring energy prices across Europe, the European Commission proposed, as part of the FitFor55 climate and energy package, the EU Social Climate Fund to mitigate the expected social impact of extending the EU ETS to transport and heating.
The report presented in this webinar provides an update of the European Energy Poverty Index, published for the first time in 2019, which shows the combined effect of energy and mobility poverty across Member States. Beyond the regular update of the index, the report provides analysis of the existing EU policy framework related to energy and transport poverty. France is used as a case study given the “yellow vest” movement, which was triggered by the proposed carbon tax on fuels.
Watch the recordings of the webinar:
https://youtu.be/i1Jdd3H05t0
Does the EU Emission Trading Scheme ETS Promote Energy Efficiency?Leonardo ENERGY
This policy brief analyzes the main interacting mechanisms between the Energy Efficiency Directive (EED) and the EU Emission Trading Scheme (ETS). It presents a detailed top-down approach, based on the ODYSSEE energy indicators, to identify energy savings from the EU ETS.
The main task consists in isolating those factors that contribute to the change in energy consumption of industrial branches covered by the EU ETS, and the energy transformation sector (mainly the electricity sector).
Speaker:
Wolfgang Eichhammer (Head of the Competence Center Energy Policy and Energy Markets @Fraunhofer Institute for Systems and Innovation Research ISI)
The recordings of this webinar can be watched via:
https://youtu.be/TS6PxIvtaKY
Energy efficiency, structural change and energy savings in the manufacturing ...Leonardo ENERGY
The first part of the presentations presents the energy efficiency improvements in the manufacturing sector since 2000, and the role of structural change between the different branches and energy savings. It will compare the improvements in Denmark and other countries with EU average. This part is based on ODYSSEE data.
The second part of the presentation presents the development in Denmark in more detail, and it will compare the energy efficiency improvement, corrected for structural change, with the reported savings from the Energy Efficiency Obligation Scheme.
Recordings of the live webinar are on https://youtu.be/VVAdw_CS51A
Energy Sufficiency Indicators and Policies (Lea Gynther, Motiva)Leonardo ENERGY
This policy brief looks at questions ‘how to measure energy sufficiency’, ‘which policies and measures can be used to address energy sufficiency’ and ‘how they are used in Europe today’.
Energy sufficiency refers to a situation where everyone has access to the energy services they need, whilst the impacts of the energy system do not exceed environmental limits. The level of ambition needed to address energy sufficiency is higher than in the case of energy efficiency.
This is the 13th edition of the Odyssee-Mure on Energy Efficiency Academy, and number 519 in the Leonardo ENERGY series. The recording of the live presentation can be found on https://www.youtube.com/watch?v=jEAdYbI0wDI&list=PLUFRNkTrB5O_V155aGXfZ4b3R0fvT7sKz
The Super-efficient Equipment and Appliance Deployment (SEAD) Initiative Prod...Leonardo ENERGY
The Super-efficient Equipment and Appliance Deployment (SEAD) Initiative Product Efficiency Call to Action, by Melanie Slade - IEA and Nicholas Jeffrey - UK BEIS
2. PHOTOVOLTAIC SYSTEM
Design, Execution, Operation & Maintenance
STAND ALONE FACILITIES
Javier Relancio. Generalia Group. 06/10/2010
www.generalia.es
2
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
3. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
3
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
4. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
4
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
5. Basic topology
PV modules
PV regulator
DC Consumption
Inverter AC Consumption
5
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
6. Introduction
Differences with a grid connected system
Designed for self-consumption
An electricity storage is required
Regulator / charger
Batteries
Inverters with capacity " to create a grid"
For facilities with consumptions in DC and output power below 2 kW, we may require modules
with particular characteristics:
If the consumptions are in DC 12 V, modules of 18 V
If they are in DC 24 V, modules of 30-32 V
NOTE: The modules of 12 V are more expensive, but it is possible to avoid their use by using
regulators with power maximizers. Only for powers over 2 kW
6
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
7. Introduction
Criterion of “winter production maximization” VS “annual production maximization”
In the grid connected facilities, the objective is to obtain the maximum annual profitability of
the installation
In stand-alone facilities, the objective is to feed the demand for any day of the year. For it:
We have to design the installation for the " worse day of the year "
We will choose the modules tilt that maximizes the production in the above mentioned
month
Sofia, Bulgaria Madrid, Spain 6
Ed (32º) Ed (61º) Ed (34º) Ed (60º)
Jan 1,65 1,79 2,66 2,96 5
Feb 2,25 2,34 3,05 3,19
Mar 2,75 2,63 4,32 4,23 4
Apr 3,42 3,01 4,1 3,63
3
May 3,61 2,95 4,63 3,75
Jun 3,79 2,97 4,78 3,69 2
Jul 4,06 3,23 4,91 3,85
Aug 3,95 3,37 4,79 4,08 1
Sep 3,48 3,28 4,38 4,14
Oct 2,68 2,74 3,54 3,63 0
Nov 1,71 1,84 2,66 2,9 Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec
Dec 1,3 1,41 2,15 2,39
Sofia, Bulgaria (32º) Sofia, Bulgaria (61º)
Total year 1050 960 1400 1290 Madrid, España (34º) Madrid, España (60º)
7
Note: we can use backup system for the worst production months
8. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
8
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
9. Elements
Inverter
Lower range of powers than for grid connected facilities
Possibility of connection in parallel or series
Prepared for auxiliary inputs in parallel, in case of hybrid systems:
diesel, grid, modules …
Manufacturers:
Manufacturer Power (per unit) System Power Observations
• It integrates a battery charger
• It allows to inject surplus to the grid
Xantrex 6 kW 36 kW
• It allows different configuration modes for the
management of the generation and the consumption
• It integrates a battery charger
100 kVA
Victron 10 kVA • It allows different configuration modes for the
(90 kW)
management of the generation and the consumption
• It integrates a battery charger
Ingeteam 15 kVA 120 kVA • It allows different configuration modes for the
management of the generation and the consumption
9
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
10. Elements
Regulator / Charger
It is used to:
... protect the batteries against overcharging
To avoid excessive discharges within a cycle
It is recommended to work with a oversizing of 125 %
Differences between regulator and charger
Charger: it is only used to charge the batteries
Regulator: it is used both for charging the batteries and
managing the loads in DC
NOTE: The chargers are not simple devices:
The battery charge stage depends on many factors and is difficult to determine
Multiple algorithms exist to optimize the battery charging and to increase its
lifetime
10
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
11. Batteries
Introduction
Batteries are used for storing the energy that is produced by the
modules during the day, for being consumed in the periods that
there is no solar irradiation
This storage takes place due to chemical reversible reactions
A battery is composed by the connection of several "cells” in series
Between the electrodes there is a certain potential difference (Generally: 2V)
In photovoltaic applications we can generally find batteries of 12, 24 or 48 volts
Normally, the system is designed to store energy for several days of consumption
In case of several days of low irradiation: clouds, rain, etc
Three days can be a good recommendation, depending on each case
11
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
12. Batteries
Capacity
Electricity that can be obtained during a full discharge of a completely charged battery
The capacity, in Amperes - hours (A - h), is the current that the battery can supply,
multiplied by the number of hours in which the above mentioned current is delivered
Real capacity
Theoretically, a battery of 200 A - h might supply: 200A during an hour, 100A for two hours,
1A for 200 hours and so on.
However, in the reality, the capacity of the battery will change according to the regime of
charge and discharge. (Generally, lower speed of discharge implies a bigger capacity)
For example: a battery which specifies a capacity of 100 A - h during 8 hours (C-8):
It might supply 12,5 A during 8 hours. C = 12.5 x 8 = 100 A - h
But it might provide 5.8 A during 20 hours. C ' = 5.8 x 20 = 116 A - h
12
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
13. Batteries
Depth of discharge
Percentage of the total capacity of the battery that can be used without need of recharge
and without damaging the battery.
As a general rule, the less depth of discharge is reached in every cycle, the longer
the battery lifetime will be
Classification:
Light cycle Deep cycle
‐ Designed for high current in the initial ‐ Designed for long periods of utilization without
discharges being recharged
‐ Constant charges and discharges ‐ They are more robust and have higher energetic
‐ Depths of discharge lower than 20 % density
‐ Depth of discharge around of 80 %'
Note: This classification is generally used for Lead-Acid batteries
Several manufacturers
Isofoton, Hoppecke, BAE, TABB, Tudor, etc
14. Batteries
Type of batteries
For photovoltaic applications the most suitable batteries are the stationary ones, designed to
have a fixed emplacement and for the cases in which the consumption is more or less
irregular. The stationary batteries do not need to supply high currents during brief periods of
time, but they need to reach deep discharges
Lead – Acid Lead – Acid Gel-Cell NiCad
(deep cycle) (light cycle)
Observations • High commercial • High commercial • The acid is in gel • Better performance
availability availability state with high temperature
• Sudden death could • Sudden death could • They need less • They cost the double
happen happen maintenance than Lead – Acid
• They are • They are manufactured • They can operate in batteries
manufactured with with lead - calcium any position
lead – antimony • They are more
expensive than lead
batteries
Discharge depth 40-80% 15-25% 15-25% 100%
Self – discharge per month 5% 1-4% 2-3% 3-6%
Typical capacity (Ah/m3) 35,314 24,720 8,828 17,660
Capacity range (Ah/m3) 7,062 to 50,323 5,791 to 49,000 3,672 to 16,400 3,630 to 34,961
Typical capacity (Ah/Kg) 12.11 10.13 4.85 11.10
Capacity range (Ah/Kg) 4.18 to 26.65 2.42 to 20.26 2.20 to 13.87 2.64 to 20.90
Minimal temperature (oC) -6.6 -6.6 -18 -45
15. Diesel generator
The diesel generator as a backup (I)
The use of a diesel generator can allow us to avoid the oversizing of solar modules
and batteries.
The diesel generator would cover the periods of low irradiation or the situations of
extraordinary consumption
Nowadays, the energy generated by a diesel group can be more expensive than
the energy obtained from a photovoltaic solar system
It will depend on the price of the fuel in each country
NOTE: In the following slide we can find an example
15
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
16. Diesel generator
Price per kWh: Diesel generator VS Solar Facility
1,40
1,20
1,00
0,80
0,60
0,40
0,20
‐
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Precio kWh hibrido Precio kWh G Diesel Precio kWh G Diesel CO2
Notes:
1. For this study we have considered that the price of the electricity from a Diesel Generator is, today, 0.35 € per
kWh (Including the costs that the logistics of the fuel supposes).
2. The study has considered a radiation of 1500 HSP
3. In the graph we can find, in green, an estimation of the repercussion that would suppose the extra charges for
the emission of pollutant gases (Price of ton of CO2).
4. The prices are in Euros
5. The word "hybrid" refers to a photovoltaic installation with a diesel generator as a backup.
16
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
17. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
17
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
18. Hybrid System: Diesel - Solar
Inverter
PV regulator DC
Consumption
AC
PV modules Consumption
The generator is connected to the AC BUS The chosen diesel generator must have
The diesel generator is automatically switched on if automatic starter:
the batteries are under a certain level Using its own electronic starter to
The generator can produce energy exclusively to automatically switch on when an auxiliary
supply the consumption or, also, to charge the batteries signal is received
The inverter has to be specially designed with Using an external electronic starter
this function (AC/DC Converter) specially designed for this function
18
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
19. Hybrid System: Wind - Solar
Description
This type of system is currently being studied on the R&D departments of many
institutions and companies.
Good correlation between the wind and the solar resource
Generally, the wind & solar systems are connected to the DC BUS (of the batteries)
There is not too much information about the wind resource
The guarantees for the wind system are lower than for the PV system
Average, three years
The wind potential is determined by:
Speed of the wind: the kinetic energy of the wind
increases according to the cube of its speed
Wind resources become exploitable where
average annual wind speeds exceed 4‐5 m/s
Also it is influenced, to a lesser extent, by the
characteristics and density of the wind
19
20. Hybrid System: Wind - Solar
Topology
PV
modules
PV
DC Consumption
regulator
DC BUS
Wind
regulator
Inverter
AC Consumption
Wind
generator
20
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
21. Efficiency in the consumption (I)
The importance of reducing the consumption …
Nowadays, we can find great evolutions in the consumption reduction of many
massive devices: electrical appliances, lighting, air conditioning, PCs, etc
Considering the high initial investment per kWp for an isolated solar system…
and considering the dependency between this peak power and the consumption…
…every stand alone solar facility should begin by the
optimization of its consumption efficiency
Example:
Electricity price: 0,40 € per kWh
Fridge consumption “A+ Class”: 150 kWh/year Saving: 260 € per year
Source: IDAE
Fridge consumption “G Class”: 800 kWh/year
* If we reduce our energy consumption, installing a more efficient
21 device, we will be able to reduce the price of our solar PV Facility
22. Consumption efficiency (II)
Examples
Low Ordinary
Element Energy Energy
consumption consumption More efficient class consumption Evaluation
Class A Class G
Fridge
150 kWh/year 800 kWh/year LOW
Washing Class A Class G
Machine 1.42 kWh 6.9 kWh MED
Incandescent LED
Lighting 1
100 W 10 W HIGH
Incandescent Low Consumption
Lighting 2 Less efficient
100 W 18 W
PC
250 W 70 W
(Desktop)
22
23. Smart Grids (I)
Global objective
International governments commitment (such as the EU)
Minimize the environmental impact.
Reduce the CO2 emissions
Reduce the dependency from fossil fuels
Increase the use of Renewable Energies
Reduce costs & Increase the energy efficiency
To success:
Increase the integration of renewable
energies in the Global electric grid
The need of dealing with an
intermittent & distributed generation
23
24. Smart Grids (II)
Mechanisms towards the smart grids
Improve the control & supervision of the generation Demand profile for an
average day in Spain
Intermittent generation profile of the Renewable Energies
Low forecast on the production
Improve the demand management
High peak–valley ratio
Low correlation with renewable production
Improve the international grid connection
Source: REE
Improve the electricity storage
New facilities to pump water and then produce energy
R&D for new in situ storage systems: hydrogen/ batteries
The electrical vehicle
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
25. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
25
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
26. Application Areas
Zones distant from the grid
Zones currently supplied by diesel generators
Exceptionally, areas with instabilities from the grid
Great potential in
African countries
Especially, areas with
high fuel prices
Source: World energy outlook 2009
26
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
27. Application examples
Single family houses
Public buildings: hospitals, schools, etc
Public lighting and traffic lights
Communication Stations
Water pumping
For human consumption
For agriculture
Desalination & Water sewerage
Industrial uses
27
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
28. Particular case:
Water pumping facilities
Great advantages to be fed with solar
energy:
There is no need for batteries
The construction of a high water tank
can be used as a energy storage
Therefore we do not need regulator
either
Neither inverters
Nowadays, we can find great quality
DC bombs
Installation with few elements:
We reduce the price of the installation
We reduce the possibilities of
breakdown
28
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
29. Other considerations
Limits on the system Lead-Acid batteries, each cell
allows a maximum of
Maximum power output 3.000Ah en C-10(2V).
If we are using 48 V rows,
It is limited by the inverters: nowadays <120 kWp which is generally the
maximum voltage that we can
use, each row would store
Maximum capacity of storage up to:
3.000 Ah x 48 V = 144 kWh
It is limited by the batteries
Lead - acid: it is recommended not to install more than three or four blocks of
batteries in parallel
If we use Ni-Cad this quantity can be higher (according to the manufacturers) *
* It is recommended to verify this information with the manufacturer
Towards the system scalability
With the goal to supply energy to growing populations
By the mix of different technologies
29
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
30. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
30
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
31. System design (I)
Study of consumptions
We begin by creating a table with all the consumptions we will find in the system
Device Number of Peak Average Hours of usage Consumed energy
Units Power (W) Power (W) (h per day) (Wh per day)
Lamp 10 11 88* 8 880
PC 1 300 150 6 900
Fridge 1 1000 400 24 9600
TV 1 90 90 8 720
TOTAL 1500 W 728 W 12.100 Wh per day
* Simultaneity ratio 80%
The peak power will affect the inverter calculation
The daily energy consumption will affect:
The storage system
The solar modules
31
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
32. System design (II)
Solar generator calculation
According to the consumption study, we have to produce 12.100 Wh per day (average)
As we have explained previously, this production must be guaranteed even the worst
day of the year, in this case, in December
Madrid, España We have to consider the losses in all the elements of the system:
Ed* (34º) Ed* (60º)
Jan 2,66 2,96 modules, inverters, chargers, batteries and cables.
Feb 3,05 3,19
Mar 4,32 4,23
Apr 4,1 3,63 The battery losses can be estimated around 15 %
May 4,63 3,75
Jun 4,78 3,69 The whole system losses, can be estimated around 34 %
Jul 4,91 3,85
Aug 4,79 4,08
Sep 4,38 4,14 Energydemanded 12100
Oct 3,54 3,63 Psolar = = =7.670,85W
Nov
Dec
2,66
2,15
2,9
2,39
HSP× Losses 2,39 × 0,66
Total year 1400 1290
*Ed: Average daily electricity
production for 1kWp We could install, for example:
34 modules of 230 W = 7.820 Wp
32
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
33. System design (III)
Battery calculation
According to the consumption study, the batteries should supply 12.100 Wh/day (average)
In this example, the system will consider that the batteries have to be able to store energy
for two days without solar radiation
The batteries, then, should be able to store 24.200 Wh
For this example, we will choose Lead-Acid batteries, with a Cycle-Depth of 80%
In order to increase the battery life-time, we will consider a maximum discharge
depth around 60 %
We will consider the battery losses around 15%.
Energy demand × nº days 12100 × 2
Capacity A−h = = = 1977.12 A − h
Discharge depth× Losses × Voltage 0,6 × 0,85 × 24
Conclusion: 12 batteries of 2000 A-h (C-20)
33
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
34. System design(IV)
Inverter calculation (I)
Now, we have to consider the peak power of the system
In this case, the maximum power would be 1500 Wp
However, usually we use a “Simultaneity Ratio”, because normally all the devices will
not be connected at the same time
Furthermore, the inverters are prepared to supply the double of their nominal output
power, during a certain period of time
In this case, we will consider that the
peaks from the washing machine and
the fridge will not be longer than these
periods
34
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
35. System design (V)
Inverter calculation (II)
We will reach a maximum output power of 1500 Wp, so the Nominal Output
Power should be higher than 750 Wp
Considering the average consumptions, and applying a “Simultaneity Ratio” of
80% for the lights, the nominal Output Power of the inverter should be higher
than 728 Wp
So, we will choose any inverter with a Nominal Output
Power higher than 750 Wp
35
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
36. System design (VI)
Conclusions
Demanded energy: 12.100 Wh
Solar modules peak power: 7.820 Wp
Batteries capacity: 2.000 A-h (C-20) x 24 V = 48.000 W-h
Inverter nominal output power: 750 – 1000 Wp
Observations
We have considered that the consumption is homogeneous during the year
If this was not the case (For example, if we had an air conditioning system) we
would have studied also the maximum demanding day
We could reduce the amount of batteries, by reducing their autonomy or increasing
their discharge depth and introducing a diesel generator as a backup for the periods
that the batteries cannot assume
36
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
37. INDEX
Introduction
Elements. Storage System & Backup System
Trends: Hybrid Systems. Efficiency. Smart Grids
Applications. Examples
Design
Maintenance
37
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
38. Solar modules maintenance
Periodical cleaning of the modules
Depending on the pollution of each area
Generally, once per year
Checking the cables and connections
Retightening the screws
Checking the structure
If it is not protected against open air (aluminum, galvanized steel, etc) it will
require a periodical antioxidant paint
Checking any shadowing effect
38
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
39. Batteries maintenance (I)
The battery is a dangerous element, due to its chemical and electrical properties
Main risks
The electrolyte is, generally, dilute acid: it may
produce burns if contacting the skin or the eyes
Electrocution risk Recommendations:
From 24 V, in wet environments Use appropriate gloves and shoes
Use plastic handle tools
From 48 V, in dry environments
Avoid wearing any metallic object
Risk of fire or explosion Avoid sparks and flames close to the
batteries
The batteries produce hydrogen gas
An appropriate ventilation system is needed
39
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
40. Batteries maintenance (II)
Main tasks
Checking that the room is well ventilated and protected against the sun light
Checking that the electrolyte level is between the manufacturer limits
Add only distilled water
Except for Gel type batteries
Protecting the connection terminals with antioxidant grease to avoid sulfurizing
Checking the tightness of the battery connections
Cleaning the battery covers and terminals
40
http://www.leonardo-energy.org/training-pv-systems-design-construction-operation-and-maintenance
41. End of Session 6
Thank you for attending
http://www.leonardo-energy.org/training-pv-systems-design-
construction-operation-and-maintenance
41