Komponen pegas kantong merupakan tempat penyimpanan barang bawaan penumpang di belakang kursi pesawat. Pegas kantong bekerja menggunakan prinsip pegas elastis untuk memungkinkan penyimpanan dan pengambilan barang dengan mudah tanpa mengganggu aktivitas penumpang lain. Studi ini bertujuan meninjau regulasi yang dibutuhkan untuk menjadi produsen pegas kantong tersertifikasi (PMA) di Indonesia serta mempelajari langk
Studi Sertifikasi Tali Penahan Kargo (Cargo Restraint Straps)Destya Maharani
Laporan ini membahas proses sertifikasi cargo restraint straps dengan meninjau regulasi terkait seperti FAR part 25 dan TSO C172A serta jenis pengujian yang harus dilakukan. Juga diberikan gambaran mengenai produsen cargo restraint straps luar dan dalam negeri beserta bahan dasar yang digunakan.
Analisis Sertifikasi Ban Baru untuk Pesawat Udara - Major Assignment Ae4060 K...Aqil Nedhio Wibowo
Ban Pesawat merupakan salah satu barang original equipment manufacturer (OEM) pada pesawat terbang. Sehingga, produk ban yang dipakai pesawat dapat diubah dengan brand yang berbeda selama produk tersebut masih sesuai dengan kebutuhan, tersertifikasi (TSO Authorization) dan diizinkan untuk digunakan. Saat ini, terdapat PT. Garuda Maintenance Facility (GMF) AeroAsia Tbk. yang sedang merintis bisnis ban pesawat, khususnya ban vulkanisir. Walaupun begitu, hal tersebut tidak menutup kemungkinan perusahaan lain untuk ikut memproduksi ban pesawat.
Untuk dapat mendapatkan sertifikasi untuk pembuatan ban pesawat, maka pabrikan perlu untuk memenuhi regulasi dan standard yang berlaku, seperti TSO-C62e dan FAR. Beberapa persyaratan dan pengujian harus dipenuhi untuk membuktikan produknya memiliki tingkat keamanan sesuai yang tertulis di regulasi.
Laporan Tugas Besar Studi Sertifikasi Lampu Anti-TabrakanAlvinIrwanto1
Laporan ini membahas studi sertifikasi anticollision lights berdasarkan regulasi FAA TSO-C96a. Ia menjelaskan spesifikasi anticollision lights menurut regulasi, produsen LRU di dalam dan luar negeri, serta proses pengujian dan tempat pengujian yang diperlukan untuk memperoleh sertifikasi kelayakan udara.
Laporan Tugas Besar Studi Sertifikasi Selang Rem PesawatNauvalRifdan
Laporan ini membahas studi sertifikasi selang rem pesawat terbang menurut regulasi TSO-C75 milik FAA. Laporan ini menjelaskan deskripsi selang rem pesawat, produsen selang rem, regulasi terkait sertifikasi selang rem, prosedur pengujian, dan alur sertifikasi selang rem pesawat terbang."
Studi Sertifikasi Evacuation Slides (Tubes Sertifikasi Kelaikudaraan 2020)Ezra Purwa
Dokumen tersebut membahas tentang studi sertifikasi luncuran evakuasi yang meliputi deskripsi part evacuation slide, regulasi kelaikan udara terkait, jenis pengujian yang diperlukan, dan produsen evacuation slide dalam dan luar negeri. Dokumen ini disusun untuk memenuhi tugas besar mata kuliah sertifikasi kelaikudaraan."
Studi Sertifikasi Tali Penahan Kargo (Cargo Restraint Straps)Destya Maharani
Laporan ini membahas proses sertifikasi cargo restraint straps dengan meninjau regulasi terkait seperti FAR part 25 dan TSO C172A serta jenis pengujian yang harus dilakukan. Juga diberikan gambaran mengenai produsen cargo restraint straps luar dan dalam negeri beserta bahan dasar yang digunakan.
Analisis Sertifikasi Ban Baru untuk Pesawat Udara - Major Assignment Ae4060 K...Aqil Nedhio Wibowo
Ban Pesawat merupakan salah satu barang original equipment manufacturer (OEM) pada pesawat terbang. Sehingga, produk ban yang dipakai pesawat dapat diubah dengan brand yang berbeda selama produk tersebut masih sesuai dengan kebutuhan, tersertifikasi (TSO Authorization) dan diizinkan untuk digunakan. Saat ini, terdapat PT. Garuda Maintenance Facility (GMF) AeroAsia Tbk. yang sedang merintis bisnis ban pesawat, khususnya ban vulkanisir. Walaupun begitu, hal tersebut tidak menutup kemungkinan perusahaan lain untuk ikut memproduksi ban pesawat.
Untuk dapat mendapatkan sertifikasi untuk pembuatan ban pesawat, maka pabrikan perlu untuk memenuhi regulasi dan standard yang berlaku, seperti TSO-C62e dan FAR. Beberapa persyaratan dan pengujian harus dipenuhi untuk membuktikan produknya memiliki tingkat keamanan sesuai yang tertulis di regulasi.
Laporan Tugas Besar Studi Sertifikasi Lampu Anti-TabrakanAlvinIrwanto1
Laporan ini membahas studi sertifikasi anticollision lights berdasarkan regulasi FAA TSO-C96a. Ia menjelaskan spesifikasi anticollision lights menurut regulasi, produsen LRU di dalam dan luar negeri, serta proses pengujian dan tempat pengujian yang diperlukan untuk memperoleh sertifikasi kelayakan udara.
Laporan Tugas Besar Studi Sertifikasi Selang Rem PesawatNauvalRifdan
Laporan ini membahas studi sertifikasi selang rem pesawat terbang menurut regulasi TSO-C75 milik FAA. Laporan ini menjelaskan deskripsi selang rem pesawat, produsen selang rem, regulasi terkait sertifikasi selang rem, prosedur pengujian, dan alur sertifikasi selang rem pesawat terbang."
Studi Sertifikasi Evacuation Slides (Tubes Sertifikasi Kelaikudaraan 2020)Ezra Purwa
Dokumen tersebut membahas tentang studi sertifikasi luncuran evakuasi yang meliputi deskripsi part evacuation slide, regulasi kelaikan udara terkait, jenis pengujian yang diperlukan, dan produsen evacuation slide dalam dan luar negeri. Dokumen ini disusun untuk memenuhi tugas besar mata kuliah sertifikasi kelaikudaraan."
Tugas Besar Kelaikan Udara - Evacuation SlideFirza Ekadj
Laporan ini memberikan gambaran mengenai studi sertifikasi evacuation slide. Laporan ini membahas deskripsi produk evacuation slide, regulasi terkait, pengujian yang harus dilakukan, dan prosedur pengajuan sertifikasi kepada otoritas penerbangan.
Laporan hasil studi sertifikasi LRU sabuk pengaman yang dilaksanakan untuk memenuhi tugas besar mata kuliah AE3140 Sertifikasi Kelaikudaraan pada program studi Teknik Dirgantara ITB di tahun 2019.
Laporan tugas besar lampu navigasi pesawatIqbalArdy1
Pada laporan ini akan dijelaskan tentang studi lampu navigasi pesawat dengan menggunakan literatur dan sumber-sumber daring lainnya. Studi ini memuat gambaran umum mengenai topik, produsen yang tersedia dan potensial, proses pengujian secara umum, regulasi, dan tempat pengujian topik yang kami angkat.
Studi sertifikasi dudukan lengan kursi pada pesawat udaraKevin Horasio
Laporan ini membahas desain, regulasi, dan proses sertifikasi armcap pada kursi pesawat. Beberapa poin utama yang diangkat antara lain: (1) penjelasan mengenai produk armcap dan produsen-produsen yang sudah memproduksinya, (2) analisis regulasi terkait seperti FAR 25.853 dan TSO, (3) pengujian yang perlu dilakukan seperti uji bakar dan beban statis.
Tugas Besar AE3140 Sertifikasi Kaca Depan Kokpit (Windshield)M. Satryo Sahara
Laporan ini membahas windshield atau kaca depan kokpit pesawat. Secara ringkas, dibahas fungsi windshield untuk melindungi kokpit dari aliran fluida di depan pesawat dan memberikan visibilitas kepada pilot, konstruksi sistem windshield yang terdiri dari beberapa lapis kaca dan material pengikat, serta sistem kerja windshield untuk mencegah icing menggunakan pemanasan listrik.
AirAsia Indonesia QZ8501 hilang kontak pada Desember 2014 saat terbang dari Surabaya ke Singapura dengan 162 penumpang. Pesawat jatuh di Laut Jawa. CEO AirAsia langsung menyatakan bela sungkawa dan berkomunikasi dengan keluarga korban. AirAsia juga secara responsif menggunakan media sosial untuk berbagi informasi terkini mengenai insiden ini.
Studi Sertifikasi TSO-C97 Baterai Litium Sulfur DioksidaRonald Sianturi
Jikalau para peseluncur internet berkenan untuk mengetahui proses sertifikasi baterai pesawat, ini tempat yang pas untuk Anda. Kalau kalian salah alamat dan mau buka YouTube, klik youtube.com.
Modul pelatihan ini membahas tentang pelepasan dan pemasangan bantalan anti gesek pada kendaraan ringan. Modul ini terdiri atas empat kegiatan yang mencakup pelajaran, respon, praktek, dan penilaian untuk memberikan pengetahuan dan keterampilan kepada peserta pelatihan dalam mengidentifikasi, melepas, dan memasang bantalan anti gesek secara benar.
Pesawat AirAsia QZ8501 yang terbang dari Surabaya menuju Singapura tanggal 28 Desember 2014 hilang kontak di Laut Jawa. Pesawat Airbus A320 membawa 155 penumpang dan 7 kru. Dilakukan pencarian besar-besaran namun belum ditemukan sampai sekarang. Ditemukan beberapa pelanggaran dan peringatan terkait kecelakaan ini.
[Ringkasan]
Laporan ini membahas kerja praktek yang dilakukan di PT Toyota Motor Manufacturing Indonesia (TMMIN). Tujuan kerja praktek ini adalah untuk memperoleh pengalaman kerja langsung di industri otomotif, mempelajari sistem dan alur kerja di TMMIN, serta mempersiapkan lulusan yang siap bekerja sesuai tuntutan dunia industri. Penulis ditempatkan di divisi Sourcing Planning yang menangani perencanaan pasokan suku cadang.
Laporan Kerja Praktek - PT. Inti Ganda PerdanaRidwan Arifin
Proses unboxing part CKD, penetapan jumlah tenaga kerja optimal pos unboxing part dengan metode standarisasi kerja tipe 3, dan pembuatan SOP penempatan part axle shaft dengan mekanisme FIFO di PT. Inti Ganda Perdana.
Visi Misi dan Program IATCA 2023-2027 (Setio).pdfssuser9b388d
Program kerja 2023-2027 mencakup modernisasi organisasi IATCA, perluasan keanggotaan dan pelatihan, serta dukungan penyaluran tenaga ATC. Ada juga program kolaborasi dengan AirNav untuk pembenahan remunerasi, karier, formasi dan mutasi ATC.
Proposal ini mengajukan permohonan untuk melaksanakan kerja praktek di PT. Bridgestone Tire Indonesia yang berfokus pada analisis efisiensi boiler. Tujuannya antara lain untuk menerapkan teori, mengenal alat dan proses produksi, serta mempelajari struktur organisasi perusahaan. Kerja praktek akan dilaksanakan selama satu bulan oleh seorang mahasiswa teknik mesin dengan metode wawancara, observasi, dan studi literatur.
Laporan ini membahas aktivitas periodik service pada unit HD 785-7 di PT Kalimantan Prima Persada. Aktivitas meliputi persiapan seperti mempersiapkan dokumen, spare part, dan membersihkan unit sebelum dilakukan penggantian oli, filter, dan pengecekan berkala sesuai prosedur.
Laporan Kerja Praktik Komatsu Indonesia oleh Muhammad AkmalMuhammad Akmal
Laporan ini membahas pelaksanaan kerja praktik di PT Komatsu Indonesia selama 1 bulan. Mahasiswa melakukan analisis pengaruh perubahan arus listrik pada proses pengelasan terhadap karakteristik baja paduan SS400. Eksperimen dilakukan dengan mengubah arus las pada proses pengelasan gas metal arc welding (GMAW) dan menguji hasil las dengan beberapa uji seperti ultrasonik, kekerasan, dan mikrostruktur.
Tugas Besar Kelaikan Udara - Evacuation SlideFirza Ekadj
Laporan ini memberikan gambaran mengenai studi sertifikasi evacuation slide. Laporan ini membahas deskripsi produk evacuation slide, regulasi terkait, pengujian yang harus dilakukan, dan prosedur pengajuan sertifikasi kepada otoritas penerbangan.
Laporan hasil studi sertifikasi LRU sabuk pengaman yang dilaksanakan untuk memenuhi tugas besar mata kuliah AE3140 Sertifikasi Kelaikudaraan pada program studi Teknik Dirgantara ITB di tahun 2019.
Laporan tugas besar lampu navigasi pesawatIqbalArdy1
Pada laporan ini akan dijelaskan tentang studi lampu navigasi pesawat dengan menggunakan literatur dan sumber-sumber daring lainnya. Studi ini memuat gambaran umum mengenai topik, produsen yang tersedia dan potensial, proses pengujian secara umum, regulasi, dan tempat pengujian topik yang kami angkat.
Studi sertifikasi dudukan lengan kursi pada pesawat udaraKevin Horasio
Laporan ini membahas desain, regulasi, dan proses sertifikasi armcap pada kursi pesawat. Beberapa poin utama yang diangkat antara lain: (1) penjelasan mengenai produk armcap dan produsen-produsen yang sudah memproduksinya, (2) analisis regulasi terkait seperti FAR 25.853 dan TSO, (3) pengujian yang perlu dilakukan seperti uji bakar dan beban statis.
Tugas Besar AE3140 Sertifikasi Kaca Depan Kokpit (Windshield)M. Satryo Sahara
Laporan ini membahas windshield atau kaca depan kokpit pesawat. Secara ringkas, dibahas fungsi windshield untuk melindungi kokpit dari aliran fluida di depan pesawat dan memberikan visibilitas kepada pilot, konstruksi sistem windshield yang terdiri dari beberapa lapis kaca dan material pengikat, serta sistem kerja windshield untuk mencegah icing menggunakan pemanasan listrik.
AirAsia Indonesia QZ8501 hilang kontak pada Desember 2014 saat terbang dari Surabaya ke Singapura dengan 162 penumpang. Pesawat jatuh di Laut Jawa. CEO AirAsia langsung menyatakan bela sungkawa dan berkomunikasi dengan keluarga korban. AirAsia juga secara responsif menggunakan media sosial untuk berbagi informasi terkini mengenai insiden ini.
Studi Sertifikasi TSO-C97 Baterai Litium Sulfur DioksidaRonald Sianturi
Jikalau para peseluncur internet berkenan untuk mengetahui proses sertifikasi baterai pesawat, ini tempat yang pas untuk Anda. Kalau kalian salah alamat dan mau buka YouTube, klik youtube.com.
Modul pelatihan ini membahas tentang pelepasan dan pemasangan bantalan anti gesek pada kendaraan ringan. Modul ini terdiri atas empat kegiatan yang mencakup pelajaran, respon, praktek, dan penilaian untuk memberikan pengetahuan dan keterampilan kepada peserta pelatihan dalam mengidentifikasi, melepas, dan memasang bantalan anti gesek secara benar.
Pesawat AirAsia QZ8501 yang terbang dari Surabaya menuju Singapura tanggal 28 Desember 2014 hilang kontak di Laut Jawa. Pesawat Airbus A320 membawa 155 penumpang dan 7 kru. Dilakukan pencarian besar-besaran namun belum ditemukan sampai sekarang. Ditemukan beberapa pelanggaran dan peringatan terkait kecelakaan ini.
[Ringkasan]
Laporan ini membahas kerja praktek yang dilakukan di PT Toyota Motor Manufacturing Indonesia (TMMIN). Tujuan kerja praktek ini adalah untuk memperoleh pengalaman kerja langsung di industri otomotif, mempelajari sistem dan alur kerja di TMMIN, serta mempersiapkan lulusan yang siap bekerja sesuai tuntutan dunia industri. Penulis ditempatkan di divisi Sourcing Planning yang menangani perencanaan pasokan suku cadang.
Laporan Kerja Praktek - PT. Inti Ganda PerdanaRidwan Arifin
Proses unboxing part CKD, penetapan jumlah tenaga kerja optimal pos unboxing part dengan metode standarisasi kerja tipe 3, dan pembuatan SOP penempatan part axle shaft dengan mekanisme FIFO di PT. Inti Ganda Perdana.
Visi Misi dan Program IATCA 2023-2027 (Setio).pdfssuser9b388d
Program kerja 2023-2027 mencakup modernisasi organisasi IATCA, perluasan keanggotaan dan pelatihan, serta dukungan penyaluran tenaga ATC. Ada juga program kolaborasi dengan AirNav untuk pembenahan remunerasi, karier, formasi dan mutasi ATC.
Proposal ini mengajukan permohonan untuk melaksanakan kerja praktek di PT. Bridgestone Tire Indonesia yang berfokus pada analisis efisiensi boiler. Tujuannya antara lain untuk menerapkan teori, mengenal alat dan proses produksi, serta mempelajari struktur organisasi perusahaan. Kerja praktek akan dilaksanakan selama satu bulan oleh seorang mahasiswa teknik mesin dengan metode wawancara, observasi, dan studi literatur.
Laporan ini membahas aktivitas periodik service pada unit HD 785-7 di PT Kalimantan Prima Persada. Aktivitas meliputi persiapan seperti mempersiapkan dokumen, spare part, dan membersihkan unit sebelum dilakukan penggantian oli, filter, dan pengecekan berkala sesuai prosedur.
Laporan Kerja Praktik Komatsu Indonesia oleh Muhammad AkmalMuhammad Akmal
Laporan ini membahas pelaksanaan kerja praktik di PT Komatsu Indonesia selama 1 bulan. Mahasiswa melakukan analisis pengaruh perubahan arus listrik pada proses pengelasan terhadap karakteristik baja paduan SS400. Eksperimen dilakukan dengan mengubah arus las pada proses pengelasan gas metal arc welding (GMAW) dan menguji hasil las dengan beberapa uji seperti ultrasonik, kekerasan, dan mikrostruktur.
“ANALYSIS TERJADINYA HYDRAULIC LOCK MENGGUNAKAN METODE WHY TREE ANALYSIS PADA...Heri Saputra
Ringkasan dokumen tersebut adalah:
1. Dokumen tersebut merupakan halaman pengesahan laporan kerja praktek di PT. Chevron Pacific Indonesia.
2. Mahasiswa melakukan kerja praktek selama 23 hari untuk menganalisis terjadinya hydraulic lock pada engine tipe 3306 Caterpillar.
3. Dokumen tersebut memuat daftar isi laporan kerja praktek.
LAPORAN KERJA PRAKTEK MENENTUKAN BEBAN KERJA PADA DEPARTEMEN LOGISTIK BAGIAN ...Agam Real
Laporan ini membahas penentuan beban kerja pada Departemen Logistik bagian Purchasing PT. Ebako Nusantara dengan menggunakan metode Full Time Equivalent (FTE). Penelitian ini menganalisis kegiatan dan waktu kerja karyawan untuk menghitung beban kerja tahunan. Hasil analisis menunjukkan bahwa jumlah tenaga kerja yang dibutuhkan per tahun untuk mendukung aktivitas purchasing.
Mesin CNC horizontal jig boring Yasda di PT. PINDAD digunakan untuk memproduksi berbagai produk. Laporan ini menjelaskan pemeliharaan mesin tersebut, mulai dari prinsip kerjanya, bagian-bagian, sistem pelumasan, dan pemeliharaan harian dan bulanan yang dilakukan.
Laporan ini merangkum Praktik Kerja Industri (PRAKERIN) di PT. LG Electronics Indonesia yang meliputi proses inspeksi detail pada produk monitor UltraWide. Pelaksanaan PRAKERIN memberikan pengalaman langsung tentang prosedur inspeksi elektronika industri.
Program kerja IATCA periode 2023-2027 mencakup modernisasi organisasi, perluasan keanggotaan dan pelatihan, dukungan penyaluran ATC, serta kebijakan serikat pegawai untuk meningkatkan kinerja organisasi dan anggotanya. Beberapa program bekerja sama dengan AirNav untuk meningkatkan remunerasi, karier, dan kebijakan formasi ATC.
Similar to Major assignment kelaikan pegas kantong (20)
1. i
STUDI PENGAPLIKASIAN CASR 21 UNTUK
“KOMPONEN PEGAS KANTONG PADA KURSI PENUMPANG PESAWAT UDARA”
Tugas Besar
Diajukan untuk Memenuhi Syarat Kelulusan Mata Kuliah AE4060 Kelaikan Udara
Oleh:
Ovi Prina Gastriani 13611023
Febrina Putri Situmorang 13612035
Raras Ayusyalita 13612027
Dosen:
Dr. Ir. Rais Zain M.Eng.
PROGRAM SARJANA AERONOTIKA DAN ASTRONOTIKA
FAKULTAS TEKNIK MESIN DAN DIRGANTARA
INSTITUT TEKNOLOGI BANDUNG
2016
2. ii
ABSTRAK
Pegas Kantong atau Spring Pocket merupakan pegas yang berada di dalam tempat
menyimpan carry-on articles (Literature Pocket) yang terdiri dari majalah, literatur, dan kartu
petunjuk keselamatan yang dikategorikan sebagai Stowage Compartments. Meski interval
penggantiannya di pesawat udara cukup panjang sehingga demand terhadap produk ini kecil,
produksinya cukup mudah. Kemudahan produksi ini cukup menarik, terutama bagi organisasi
baru yang ingin mendaftarkan perusahaannya sebagai perusahaan PMA di Indonesia.
PMA atau yang sering disebut sebagai Part Manufacturer Approval merupakan
sertifikasi di bidang desain dan produksi part modifikasi maupun pengganti pada produk type
certificate. Perusahaan PMA lokal di Indonesia belum ada. Apabila akan dilakukan inisiasi
pembangunan perusahaan tipe ini di Indonesia, maka komponen pegas kantung merupakan pilihan
komponen yang menarik sebagai tahap awal sertifikasi.
Untuk membangun perusahaan PMA di Indonesia, diperlukan studi pada fasilitas testing,
regulasi yang harus dipenuhi, dan apa langkah-langkah yang harus diikuti dalam mendaftarkan
suatu instansi untuk kemudian disebut perusahaan PMA. Ditinjau dari sisi fasilitas testing,
komponen pegas kantung dapat dites dengan menggunakan fasilitas testing dalam negeri. Dari segi
regulasi, belum semua regulasi PMA yang telah diadopsi oleh DGCA. Oleh karena itu, selain
regulasi CASR, beberapa regulasi FAR dikombinasikan untuk merumuskan persyaratan-
persyaratan untuk membangun fasilitas PMA beserta pedoman yang harus diikuti dalam
mendaftar.
Meskipun kesiapan DGCA terhadap sertifikasi PMA ini masih dalam tahap belajar, bukan
hal yang mustahil untuk membangun fasilitas PMA di Indonesia. Proses yang ditempuh akan
cukup lama, namun apabila pihak akademisi ikut serta dalam percepatan proyek ini, maka bukan
hal mustahil tahun depan perusahaan PMA mulai bermunculan. Dengan bermunculannya
perusahaan PMA, Indonesia semakin berkembang ke arah kemandirian komponen peswat udara
dalam negeri.
3. iii
ABSTRACT
Spring pocket is a place to store carry-on articles consisting of magazines, literature, and
safety instructions card. It is categorized as Stowage compartments. Although the replacement
interval for this component in aircraft is long enough so that the demand for these products are
small, its production is fairly easy. Ease of production is quite interesting, especially for the new
organization who wants to register his company as a Part Manufacturer Approval certified
company.
PMA or what is often referred to as Part Manufacturer Approval is a certification in the
field of design and production for modification or replacement parts on a type certificated product.
There is no local PMA company in Indonesia yet. For those who wants to initiate a PMA company
in Indonesia, spring pocket is fairly interesting as a beginning.
To build a PMA in Indonesia, the necessary studies on testing facilities, the regulations
must be complied, and what steps must be followed in registering to be a PMA company is needed.
Concerning the testing facility, spring pocket can be tested using testing facility in the Indonesia.
In terms of regulation, not all PMA regulationss have been adopted by the DGCA. Therefore, in
addition to CASR regulation, we combine FAR regulation to formulate the requirements for
building and developing PMA facility in Indonesia.
Still in the learning phase, DGCA, it will take sometime before a PMA company will be
actually built in Indonesia. Still, it is not impossible to build the facility in Indonesia. The process
might take a long time, but if the academia participated in the acceleration of this project, it's not
impossible next year, PMA Company began to appear in Indonesia. With the emergence, Indonesia
can supply its regions demand of aircraft component supply.
4. iv
KATA PENGANTAR
Segala puji dan hormat penulis panjatkan kepada Tuhan Yang Maha Esa yang telah
menyertai penyusunan Tugas Besar ini dari awal hingga akhir. Tugas Besar ini dibuat sebagai
syarat wajib kelulusan Mata Kuliah AE4060 Kelaikan Udara.
Tidak lupa Tim Penulis mengucapkan terima kasih kepada berbagai pihak yang telah
membantu penulis dalam mengerjakan tugas akhir ini diantaranya:
Bpk. Dr. Ir. Rais Zain sebagai dosen pembimbing yang telah memberikan kritik dan saran
yang berarti bagi Tim Penulis.
Semua pihak yang tidak bisa disebutkan satu-persatu yang telah membantu dalam
penyelesaian Tugas Besar ini.
Tim penulis sadar bahwa tulisan ini masih jauh dari kesempurnaan sehingga kritik dan saran
yang membangun sangat dibutuhkan dalam proses penyempurnaannya.
Akhirnya, penulis berharap semoga Tugas Besar ini dapat bermanfaat bagi semua pihak,
terutama bagi yang membacanya.
Bandung, 08 Desember 2016
Tim Penulis
5. v
DAFTAR ISI
ABSTRAK............................................................................................................................................. ii
ABSTRACT.......................................................................................................................................... iii
KATA PENGANTAR .......................................................................................................................... iv
DAFTAR ISI.......................................................................................................................................... v
DAFTAR TABEL................................................................................................................................ vii
DAFTAR GAMBAR ...........................................................................................................................viii
DAFTAR SINGKATAN....................................................................................................................... ix
BAB I .....................................................................................................................................................1
PENDAHULUAN..................................................................................................................................1
1.1 Latar Belakang..........................................................................................................................1
1.2 Rumusan Masalah....................................................................................................................1
1.3 Tujuan Penelitian .....................................................................................................................1
1.4 Batasan Masalah......................................................................................................................2
1.5 Metodologi Penelitian..............................................................................................................2
1.6 Sistematika Penulisan...............................................................................................................2
BAB II....................................................................................................................................................4
KAJIAN PUSTAKA..............................................................................................................................4
2.1 Informasi Komponen/Part..............................................................................................................4
2.2 Basis Sertifikasi..............................................................................................................................5
2.3 Fasilitas Testing..............................................................................................................................6
2.4 Kajian Regulasi.............................................................................................................................18
2.4.1 Order 8110.42D ............................................................................................................18
2.4.2 AC No:21-55....................................................................................................................84
2.4.3 AC 21-09 Amdt 0.............................................................................................................84
2.4.4 CASR 21 Subpart G .....................................................................................................85
2.4.5 CASR 21 Subpart K .....................................................................................................86
2.4.6 CASR 21 Subpart J ......................................................................................................87
2.4.7 CASR 45.15...................................................................................................................88
2.4.8 FAR Part 25 (Subpart D, 25.562, 25.787, 25.853, Appendix F Part I) .............................89
2.4.9 AC 25.562-1B....................................................................................................................90
2.4.10 FAA InFO 09018 ............................................................................................................91
6. vi
2.5 Regulasi Non Safety................................................................................................................91
2.6 Proses Manufaktur.................................................................................................................92
2.7 Peluang Manufaktur Spring Pocket di Indonesia.....................................................................93
BAB III ................................................................................................................................................94
ANALISIS DAN PEMBAHASAN ......................................................................................................94
BAB IV.................................................................................................................................................98
KESIMPULAN DAN SARAN ............................................................................................................98
DAFTAR PUSTAKA ..........................................................................................................................99
7. vii
DAFTAR TABEL
Tabel 1 Basis Sertifikasi Desain dan Produksi Komponen Pegas Kantung................................................6
Tabel 2 Order 8110.42D........................................................................................................................84
8. viii
DAFTAR GAMBAR
Gambar 1 Metodologi Penelitian .............................................................................................................3
Gambar 2 Komponen Pegas Kantong.......................................................................................................4
Gambar 3 Literature Pocket.....................................................................................................................5
Gambar 4 Pengujian Tarik untuk Pegas Kantong .....................................................................................7
10. 1
BAB I
PENDAHULUAN
1.1 Latar Belakang
Pegas Kantong atau Spring Pocket merupakan tempat menyimpan carry-on articles yang
terdiri dari majalah, literatur, dan kartu petunjuk keselamatan yang dikategorikan sebagai
Stowage Compartments. Meski interval penggantiannya di pesawat udara cukup panjang
sehingga demand terhadap produk ini kecil, produksinya cukup mudah. Kemudahan produksi
ini cukup menarik, terutama bagi organisasi baru yang ingin mendaftarkan perusahaannya
sebagai perusahaan PMA di Indonesia.
PMA atau yang sering disebut sebagai Part Manufacturer Approval merupakan
sertifikasi di bidang desain dan produksi part modifikasi maupun pengganti pada produk type
certificate. Perusahaan PMA lokal di Indonesia belum ada. Apabila akan dilakukan inisiasi
pembangunan perusahaan tipe ini di Indonesia, maka komponen Pegas Kantong merupakan
pilihan komponen yang menarik sebagai tahap awal sertifikasi.
1.2 Rumusan Masalah
Mengingat bahwa di Indonesia saat ini belum ada perusahaan PMA lokal, dilakukan studi
pustaka untuk mengetahui apa saja langkah-langkah yang diperlukan untuk proses menjadi PMA
Pegas Kantong, apakah peraturan-peraturan pada CASR sudah memenuhi persyaratan dan seluruh
kriteria untuk PMA Pegas Kantong, dan apakah terdapat peraturan lain yang menunjang proses
sertifikasi PMA di Indonesia, untuk memudahkan pihak-pihak yang ingin melakukan namun
belum paham mengenai tahap awal proses sertifikasi komponen Pegas Kantong.
1.3 Tujuan Penelitian
• Tujuan Umum
• Meninjau kompatibilitas CASR untuk PMA Pegas Kantong melalui studi literature.
• Mengetahui langkah-langkah yang harus dilakukan untuk memperoleh sertifikasi
PMA Pegas Kantong.
11. 2
• Meninjau Regulasi lain yang sesuai dan/atau melengkapi CASR untuk PMA Pegas
Kantong.
• Studi aplicabillity CASR dan regulasi lainnya dalam pemenuhan PMA Pegas
Kantong.
• Tujuan Akademik
• Memenuhi persyaratan kelulusan mata kuliah AE 4060 Kelaikan Udara.
1.4 Batasan Masalah
• Penelitian dibatasi pada studi literature pada CASR dan regulasi lain yang berkaitan
dengan PMA Stowage Compartments.
• Studi literatur dilakukan pada regulasi-reglasi untuk pengaplikasian PMA Pegas Kantong
di Indonesia.
1.5 Metodologi Penelitian
Metodologi penelitian ini ditunjukkan pada Gambar 1.1. Penelitian ini dimulai dengan
identifikasi masalah berupa pangsa pasar komponen pengganti dan modifikasi di Indonesia
cukup besar serta tidak adanya perusahaan PMA di Indonesia.
Kajian pustaka dilakukan pada beberapa sumber berupa CMM dan internet mengenai
komponen Pegas Kantong, kajian regulasi terhadap beberapa regulasi CASR dan FAR yang
terdiri dari Order 8110.42D, Order 8120.22°, AC No: 21-55, AC No: 21.303-4, AC No: 21-43A,
AC No: 21-51, AC No: 21-37, AC No: 43-18, AC 21-09 Amdt 0, CASR 21 Subpart G;K;J,
CASR 45.15, FAR part 25 Subpart D, FAR 25.562, FAR 25.787, FAR 25.853, FAR 25
Appendix F Part I, AC 25.562-1B, dan FAA InFO 09018.
Analisis dan pembahasan dimulai dengan mengkaji regulasi terkait komponen, metode
sertifikasi yang harus diikuti oleh instansi untuk menjadi perusahaan PMA, dsb.
1.6 Sistematika Penulisan
Sistematika penulisan laporan penelitian ini sebagai berikut:
Bab 1 Pendahuluan: membahas latar belakang masalah, rumusan masalah, tujuan penelitian,
batasan masalah, metodologi penelitian, dan sistematika penulisan.
Bab 2 Kajian Pustaka: melakukan kajian pustaka komponen Pegas Kantong, fasilitas testing, serta
kajian regulasi CASR dan beberapa regulasi FAA dikarenakan regulasi yang diadopsi Indonesia
belum cukup lengkap.
12. 3
Bab 3 Analisis dan Pembahasan: membahasa análisis metode sertifikasi yang harus dilakukan
sesuai dengan requirement CASR 21 dan beberapa regulasi FAA lainnya.
Bab 4 Kesimpulan dan Saran: merupakan ringkasan dari studi regulasi dan fasilitas testing yang
dilakukan dengan memberikan beberapa kesimpulan dan saran untuk perbaikan studi sertifikasi
yang dilakukan.
Gambar 1 Metodologi Penelitian
Identifikasi Masalah
Pangsa pasar komponen
pengganti dan modifikasi di
Indonesia cukup besar
Tidak ada perusahaan PMA di
Indonesia
Bab I
Kajian Pustaka
Komponen Spring Pocket
Regulasi CASR
Regulasi FAA
Bab II
Analisis dan Pembahasan
Kajian Regulasi
Metode Sertifikasi
dsb
Bab III
Kesimpulan dan Saran
Bab IV
13. 4
BAB II
KAJIAN PUSTAKA
2.1 Informasi Komponen/Part
Pegas Kantong merupakan salah satu komponen part di kabin. Assembli produk ini
biasanya dapat dilihat di belakang kursi penumpang. Pegas Kantong merupakan kerangka bagian
dalam bagian penyimpanan majalah seperti yang tertera di Gambar 1 dan Gambar 2 mengenai
Pegas Kantong.
Pegas Kantong bekerja menggunakan prinsip pegas. Pegas bersifat elastis yaitu memiliki
kemampuan untuk kembali ke bentuk semula ketika gaya yang diberikan tersebut dihilangkan.
Keadaan dimana suatu benda tidak dapat lagi kembali ke bentuk semula akibat gaya yang diberikan
terhadap benda terlalu besar disebut sebagai batas elastis. Sehingga apabila Pegas Kantong
diberikan gaya tarik dari penumpang untuk memasukkan barang, maka posisi Pegas Kantong akan
kembali seperti sedia kala sehingga tidak akan mengganggu jalannya keluar masuk penumpang
yang akan menempati dan keluar dari kursi.
Pegas, material, proses pengujian, dan manufaktur yang digunakan pada Pegas Kantong
memiliki kemiripan dengan komponen lain yang berada di dalam kabin seperti underseat
compartment (tempat penyimpanan pelampung keselamatan), galley, dan cabinet compartment.
Sehingga, dalam pengembangannya, memungkinkan bagi perusahaan pembuat Pegas Kantong
untuk membuat komponen serupa lainnya.
Gambar 2 Komponen Spring Pocket
14. 5
Gambar 3 Literature Pocket
2.2 Basis Sertifikasi
PMA merupakan kombinasi approval di bidang desain dan produksi untuk komponen
modifikasi dan pengganti. Kepemilikan sertifikat sebagai perusahaan PMA memungkinkan suatu
instansi memproduksi dan menjual komponen. Pendaftaran sebagai perusahaan PMA merupakan
berdasarkan komponen yang akan diproduksi. Sebuah instansi dapat mengajukan permohonan
PMA untuk suatu komponen, namun harus mengikuti semua regulasi terbaru terkait sebagai
berikut:
No Regulasi Tentang Tanggal Efektif
Berlaku
1 Order 8110.42D Parts Manufacturer Approval Procedures 21 Maret 2014
2 Order 8120.22A Production Approval Procedures 11 Januari 2016
3 AC No: 21-55 Process to Support FAA Findings of Undue
Burden or No Undue Burden for PAHs
Requesting to Use a Manufacturing Facility
Located Outside of the United States
1 Agustus 2016
4 AC No: 21.303-
4
Application for PMA Approval via Tests and
Computations or Identicality
21 Maret 2014
5 14 CFR Part 21
Subpart G
Production Certificates § 21.131- §21.150 15 November 2016
6 14 CFR Part 21
Subpart K
Parts Manufacturer Approval § 21.301-
§21.320
15 November 2016
7 14 CFR Part 45
Subpart B
Marking of Products and Articles section
45.10-45.16
15 November 2016
8 AC No: 21-43A Production under 14 CFR Part 21 Subparts
F, G, K, and O
1 Oktober 2015
9 AC No: 21-51 Applicant’s Showing of Compliance and
Certifying Statement of Compliance
28 September 2011
15. 6
10 AC No: 21-37 Primary Category Aircraft 14 Juni 1994
11 AC21-09 Amdt 0 Certification Procedures for Products and
Parts
28 Februari 1998
12 CASR 21
Subpart G
Production Certificate 9 Juni 2015
13 CASR 21
Subpart K
Part Manufacturer Approval 9 Juni 2015
14 CASR 21
Subpart J
Design Organization Approval 9 Juni 2015
15 CASR 45.15,
147.5, 184 (c),
24 (b), 65, 45.
9 Juni 2015
16 FAR Part 25: Airworthiness Standards Transport Category
Airplanes
17 FAR Part 25
Subpart D
Design and Construction
18 FAR Part 25
Section 25.562
Emergency Landing Dynamic Conditions
19 FAR Part 25
Section 25.787
Stowage Compartments
20 FAR Part 25
Section 25.853
Compartment Interiors
21 FAR Part 25
Appendix F Part
I
Test Criteria and Procedures for Showing
Compliance with FAR 25.853
22 Advisory
Circular 25.562-
1B
Dynamic Evaluation of Seat Restraint
Systems and Occupant Protection on
Transport Airplanes
10 Januari 2006
23 FAA InFO
09018:
Stowage of Items in Seat Pockets 12 November 2009
Tabel 1 Basis Sertifikasi Desain dan Produksi Komponen Pegas Kantong
2.3 Fasilitas Testing
Pegas Kantong dalam struktur pesawat dikategorikan dalam stowage compartment
sehingga menurut FAR Part 25 Subpart D tentang Design and Construction Section 25.787
mengenai Stowage Compartments menjelaskan bahwa dalam pembuatannya harus memenuhi
kebutuhan beban maksimal yang akan dialami serta ketika dalam kondisi pendaratan darurat
16. 7
apabila terjadi kerusakan pada Pegas Kantong tidak akan memberikan direct injury kepada
penumpang.
Kebutuhan beban yang dapat diterima Pegas Kantong maksimalnya menurut FAA adalah
3 pound. Menurut Advisory Circular 25.562-1B mengenai Dynamic Evaluation of Seat Restraint
Systems and Occupant Protection on Transport Airplanes adalah Pegas Kantong tidak perlu
dilakukan tes secara dinamik. Selain itu, menurut FAR Part 25 Appendix F Part I disebutkan bahwa
Pegas Kantong adalah salah satu pengecualian bagi kategori stowage compartment yang tidak
perlu memiliki kemampuan untuk memiliki material yang dapat secara otomatis memadamkan diri
ketika terjadi kebakaran sehingga juga tidak perlu melakukan tes tersebut. Oleh karena itu, tes
yang perlu dilakukan untuk menguji kelayakan Pegas Kantong adalah hanya uji statik salah
satunya dengan uji tarik.
Gambar 4 Pengujian Tarik untuk Pegas Kantong
Pengujian uji tarik ini dapat dilakukan di beberapa perusahaan pengujian di Indonesia, namun
perusahaan yang sudah mendapatkan sertifikasi DGCA untuk melakukan pengujian bagi struktur
bagian pesawat terbang adalah PT Dirgantara Indonesia (PTDI). Selain itu, terdapat cukup banyak
17. 8
perusahaan yang dapat melakukan pengujian ini namun hanya memiliki sertifikat ISO, Komite
Akreditasi Nasional, dan International Laboratory Accreditation Cooperation seperti:
1. Pusat Penelitian Metalurgi dan Material (P2MM) – LIPI
2. Balai Besar Bahan dan Barang Teknik – Kementerian Perindustrian
3. Pusat Penelitian dan Pengembangan Permukiman – Kementerian PUPR
4. SUCOFINDO – Jakarta
5. PT. Bina Andalan Karya Inspeksi – Bekasi
6. PT Global Quality Indonesia – Bandung
Selain itu, terdapat beberapa perusahaan asing yang telah memiliki sertifikasi dari EASA untuk
melakukan testing bagi komponen pesawat seperti:
1. Horiba Mira – Inggris
2. SWS Certification Services – Inggris
Proses untuk melakukan pengujian dan alat uji yang digunakan prinsip dasarnya cukup
sederhana. Berikut ini adalah konsep dasar uji tarik dan aplikasinya:
Uji tarik adalah suatu metode yang digunakan untuk menguji kekuatan suatu bahan/material
dengan cara memberikan beban gaya yang sesumbu [Askeland, 1985]. Hasil yang didapatkan dari
pengujian tarik sangat penting untuk rekayasa teknik dan desain produk karena mengahsilkan data
kekuatan material. Pengujian uji tarik digunakan untuk mengukur ketahanan suatu material
terhadap gaya statis yang diberikan secara lambat.
Pengujian tarik adalah dasar dari pengujian mekanik yang dipergunakan pada material. Dimana
spesimen uji yang telah distandarisasi, dilakukan pembebanan uniaxial sehingga spesimen uji
mengalami peregangan dan bertambah panjang hingga akhirnya patah. Pengujian tarik relatif
sederhana, murah dan sangat terstandarisasi dibanding pengujian lain. Hal-hal yang perlu
diperhatikan agar penguijian menghasilkan nilai yang valid adalah; bentuk dan dimensi spesimen
uji, pemilihan grips dan lain-lain.
18. 9
Bentuk dan Dimensi Spesimen uji
Spesimen uji harus memenuhi standar dan spesifikasi dari ASTM E8 atau D638. Bentuk dari
spesimen penting karena kita harus menghindari terjadinya patah atau retak pada daerah grip atau
yang lainnya. Jadi standarisasi dari bentuk spesimen uji dimaksudkan agar retak dan patahan
terjadi di daerah gage length.
Grip and Face Selection
Face dan grip adalah faktor penting. Dengan pemilihan setting yang tidak tepat, spesimen uji
akan terjadi slip atau bahkan pecah dalam daerah grip (jaw break). Ini akan menghasilkan hasil
yang tidak valid. Face harus selalu tertutupi di seluruh permukaan yang kontak dengan grip. Agar
spesimen uji tidak bergesekan langsung dengan face.
Beban yang diberikan pada bahan yang di uji ditransmisikan pada pegangan bahan yang di uji.
Dimensi dan ukuran pada benda uji disesuaikan dengan standar baku pengujian.
19. 10
Kurva tegangan-regangan teknik dibuat dari hasil pengujian yang didapatkan.
Tegangan yang digunakan pada kurva adalah tegangan membujur rata-rata dari pengujian tarik.
Tegangan teknik tersebut diperoleh dengan cara membagi beban yang diberikan dibagi dengan
luas awal penampang benda uji.
Regangan yang digunakan untuk kurva tegangan-regangan teknik adalah regangan linier rata-
rata, yang diperoleh dengan cara membagi perpanjangan yang dihasilkan setelah pengujian
dilakukan dengan panjang awal.
Bentuk dan besaran pada kurva tegangan-regangan suatu logam tergantung pada komposisi,
perlakuan panas, deformasi plastik, laju regangan, temperatur dan keadaan tegangan yang
menentukan selama pengujian. Parameter-parameter yang digunakan untuk menggambarkan
kurva tegangan-regangan logam adalah kekuatan tarik, kekuatan luluh atau titik luluh, persen
perpanjangan dan pengurangan luas. Dan parameter pertama adalah parameter kekuatan,
sedangkan dua yang terakhir menyatakan keuletan bahan.
20. 11
Bentuk kurva tegangan-regangan pada daerah elastis tegangan berbanding lurus terhadap
regangan. Deformasi tidak berubah pada pembebanan, daerah remangan yang tidak menimbulkan
deformasi apabila beban dihilangkan disebut daerah elastis. Apabila beban melampaui nilai yang
berkaitan dengan kekuatan luluh, benda mengalami deformasi plastis bruto. Deformasi pada
daerah ini bersifat permanen, meskipun bebannya dihilangkan. Tegangan yang dibutuhkan untuk
menghasilkan deformasi plastis akan bertambah besar dengan bertambahnya regangan plastik.
Pada tegangan dan regangan yang dihasilkan, dapat diketahui nilai modulus elastisitas.
Persamaannya dituliskan dalam persamaan
E : Besar modulus elastisitas (kg/mm2),
e : regangan
σ : Tegangan (kg/mm2
)
Pada mulanya pengerasan regang lebih besar dari yang dibutuhkan untuk mengimbangi
penurunan luas penampang lintang benda uji dan tegangan teknik (sebanding dengan beban F)
yang bertambah terus, dengan bertambahnya regangan. Akhirnya dicapai suatu titik di mana
pengurangan luas penampang lintang lebih besar dibandingkan pertambahan deformasi beban
yang diakibatkan oleh pengerasan regang. Keadaan ini untuk pertama kalinya dicapai pada suatu
titik dalam benda uji yang sedikit lebih lemah dibandingkan dengan keadaan tanpa beban. Seluruh
deformasi plastis berikutnya terpusat pada daerah tersebut dan benda uji mulai mengalami
penyempitan secara lokal. Karena penurunan luas penampang lintang lebih cepat daripada
pertambahan deformasi akibat pengerasan regang, beban sebenarnya yang diperlukan untuk
mengubah bentuk benda uji akan berkurang dan demikian juga tegangan teknik pada persamaan
(1) akan berkurang hingga terjadi patah.
Dari kurva uji tarik yang diperoleh dari hasil pengujian akan didapatkan beberapa sifat mekanik
yang dimiliki oleh benda uji, sifat-sifat tersebut antara lain [Dieter, 1993]:
21. 12
1. Kekuatan tarik
2. Kuat luluh dari material
3. Keuletan dari material
4. Modulus elastic dari material
5. Kelentingan dari suatu material
6. Ketangguhan.
Kekuatan Tarik
Kekuatan yang biasanya ditentukan dari suatu hasil pengujian tarik adalah kuat luluh (Yield
Strength) dan kuat tarik (Ultimate Tensile Strength). Kekuatan tarik atau kekuatan tarik maksimum
(Ultimate Tensile Strength / UTS), adalah beban maksimum dibagi luas penampang lintang awal
benda uji.
Untuk logam-logam yang liat kekuatan tariknya harus dikaitkan dengan beban maksimum
dimana logam dapat menahan sesumbu untuk keadaan yang sangat terbatas.
Tegangan tarik adalah nilai yang paling sering dituliskan sebagai hasil suatu uji tarik, tetapi
pada kenyataannya nilai tersebut kurang bersifat mendasar dalam kaitannya dengan kekuatan
bahan. Untuk logam-logam yang liat kekuatan tariknya harus dikaitkan dengan beban maksimum,
di mana logam dapat menahan beban sesumbu untuk keadaan yang sangat terbatas. Akan
ditunjukkan bahwa nilai tersebut kaitannya dengan kekuatan logam kecil sekali kegunaannya
untuk tegangan yang lebih kompleks, yakni yang biasanya ditemui. Untuk berapa lama, telah
menjadi kebiasaan mendasarkan kekuatan struktur pada kekuatan tarik, dikurangi dengan faktor
keamanan yang sesuai.
Kecenderungan yang banyak ditemui adalah menggunakan pendekatan yang lebih rasional
yakni mendasarkan rancangan statis logam yang liat pada kekuatan luluhnya. Akan tetapi, karena
jauh lebih praktis menggunakan kekuatan tarik untuk menentukan kekuatan bahan, maka metode
ini lebih banyak dikenal, dan merupakan metode identifikasi bahan yang sangat berguna, mirip
dengan kegunaan komposisi kimia untuk mengenali logam atau bahan. Selanjutnya, karena
22. 13
kekuatan tarik mudah ditentukan dan merupakan sifat yang mudah dihasilkan kembali
(reproducible). Kekuatan tersebut berguna untuk keperluan spesifikasi dan kontrol kualitas bahan.
Korelasi empiris yang diperluas antara kekuatan tarik dan sifat-sifat bahan misalnya kekerasan dan
kekuatan lelah, sering dipergunakan. Untuk bahan-bahan yang getas, kekuatan tarik merupakan
kriteria yang tepat untuk keperluan perancangan.
Tegangan di mana deformasi plastik atau batas luluh mulai teramati tergantung pada kepekaan
pengukuran regangan. Sebagian besar bahan mengalami perubahan sifat dari elastik menjadi
plastik yang berlangsung sedikit demi sedikit, dan titik di mana deformasi plastik mulai terjadi dan
sukar ditentukan secara teliti. Telah digunakan berbagai kriteria permulaan batas luluh yang
tergantung pada ketelitian pengukuran regangan dan data-data yang akan digunakan.
1. Batas elastik sejati berdasarkan pada pengukuran regangan mikro pada skala regangan 2 X
10-6 inci/inci. Batas elastik nilainya sangat rendah dan dikaitkan dengan gerakan beberapa
ratus dislokasi.
2. Batas proporsional adalah tegangan tertinggi untuk daerah hubungan proporsional antara
tegangan-regangan. Harga ini diperoleh dengan cara mengamati penyimpangan dari bagian
garis lurus kurva tegangan-regangan.
3. Batas elastik adalah tegangan terbesar yang masih dapat ditahan oleh bahan tanpa terjadi
regangan sisa permanen yang terukur pada saat beban telah ditiadakan. Dengan
bertambahnya ketelitian pengukuran regangan, nilai batas elastiknya menurun hingga suatu
batas yang sama dengan batas elastik sejati yang diperoleh dengan cara pengukuran
regangan mikro. Dengan ketelitian regangan yang sering digunakan pada kuliah rekayasa
(10-4
inci/inci), batas elastik lebih besar daripada batas proporsional. Penentuan batas
elastik memerlukan prosedur pengujian yang diberi beban-tak diberi beban (loading-
unloading) yang membosankan.
23. 14
Kekuatan luluh (yield strength)
Salah satu kekuatan yang biasanya diketahui dari suatu hasil pengujian tarik adalah kuat luluh
(Yield Strength). Kekuatan luluh ( yield strength) merupakan titik yang menunjukan perubahan
dari deformasi elastis ke deformasi plastis [Dieter, 1993].
Tegangan di mana deformasi plastis atau batas luluh mulai teramati tergantung pada kepekaan
pengukuran regangan. Sebagian besar bahan mengalami perubahan sifat dari elastik menjadi
plastis yang berlangsung sedikit demi sedikit, dan titik di mana deformasi plastis mulai terjadi dan
sukar ditentukan secara teliti.
Kekuatan luluh adalah tegangan yang dibutuhkan untuk menghasilkan sejumlah kecil deformasi
plastis yang ditetapkan. Definisi yang sering digunakan untuk sifat ini adalah kekuatan luluh
ditentukan oleh tegangan yang berkaitan dengan perpotongan antara kurva tegangan-regangan
dengan garis yang sejajar dengan elastis ofset kurva oleh regangan tertentu. Di Amerika Serikat
offset biasanya ditentukan sebagai regangan 0,2 atau 0,1 persen (e = 0,002 atau 0,001)
Cara yang baik untuk mengamati kekuatan luluh offset adalah setelah benda uji diberi
pembebanan hingga 0,2% kekuatan luluh offset dan kemudian pada saat beban ditiadakan maka
benda ujinya akan bertambah panjang 0,1 sampai dengan 0,2%, lebih panjang daripada saat dalam
keadaan diam. Tegangan offset di Britania Raya sering dinyatakan sebagai tegangan uji (proff
stress), di mana harga ofsetnya 0,1% atau 0,5%. Kekuatan luluh yang diperoleh dengan metode
ofset biasanya dipergunakan untuk perancangan dan keperluan spesifikasi, karena metode tersebut
terhindar dari kesukaran dalam pengukuran batas elastik atau batas proporsional.
Pengukuran Keliatan (keuletan)
Keuleten adalah kemampuan suatu bahan sewaktu menahan beban pada saat diberikan penetrasi
dan akan kembali ke baentuk semula.Secara umum pengukuran keuletan dilakukan untuk
memenuhi kepentingan tiga buah hal [Dieter, 1993]:
24. 15
1. Untuk menunjukan elongasi di mana suatu logam dapat berdeformasi tanpa terjadi patah
dalam suatu proses suatu pembentukan logam, misalnya pengerolan dan ekstrusi.
2. Untuk memberi petunjuk secara umum kepada perancang mengenai kemampuan logam
untuk mengalir secara pelastis sebelum patah.
3. Sebagai petunjuk adanya perubahan permukaan kemurnian atau kondisi pengolahan
Modulus Elastisitas
Modulus Elastisitas adalah ukuran kekuatan suatu bahan akan keelastisitasannya. Makin besar
modulus, makin kecil regangan elastik yang dihasilkan akibat pemberian tegangan.Modulus
elastisitas ditentukan oleh gaya ikat antar atom, karena gaya-gaya ini tidak dapat dirubah tanpa
terjadi perubahan mendasar pada sifat bahannya. Maka modulus elastisitas salah satu sifat-sifat
mekanik yang tidak dapat diubah. Sifat ini hanya sedikit berubah oleh adanya penambahan paduan,
perlakuan panas, atau pengerjaan dingin.
Kelentingan (resilience)
Kelentingan adalah kemampuan suatu bahan untuk menyerap energi pada waktu berdeformasi
secara elastis dan kembali kebentuk awal apabila bebannya dihilangkan [Dieter, 1993].
Kelentingan biasanya dinyatakan sebagai modulus kelentingan, yakni energi regangan tiap satuan
volume yang dibutuhkan untuk menekan bahan dari tegangan nol hingga tegangan luluh σo.
Bahan ideal untuk menahan beban energi pada pemakaian di mana bahan tidak mengalami
deformasi permanen, misal pegas mekanik, adalah data bahan yang memiliki tegangan luluh tinggi
dan modulus elastisitas rendah.
Ketangguhan (Toughness)
Ketangguhan (Toughness) adalah kemampuan menyerap energi pada daerah plastik. Pada
umumnya ketangguhan menggunakan konsep yang sukar dibuktikan atau didefinisikan. Salah satu
menyatakan ketangguhan adalah meninjau luas keseluruhan daerah di bawah kurva tegangan-
25. 16
regangan. Luas ini menunjukan jumlah energi tiap satuan volume yang dapat dikenakan kepada
bahan tanpa mengakibatkan pecah. Ketangguhan (S0) adalh perbandingan antara kekuatan dan
kueletan.
Tegangan patah sejati adalah beban pada waktu patah, dibagi luas penampang lintang.
Tegangan ini harus dikoreksi untuk keadaan tegangan tiga sumbu yang terjadi pada benda uji tarik
saat terjadi patah. Karena data yang diperlukan untuk koreksi seringkali tidak diperoleh, maka
tegangan patah sejati sering tidak tepat nilai.
Pengaruh Kekakuan Pegas
Hukum Hooke merupakan gagasan yang diperkenalkan oleh Robert Hooke yang menyelidiki
hubungan antar gaya yang bekerja pada sebuah pegas/benda elastis lainnya agar benda tersebut
bisa kembali ke bentuk semua atau tidak melampaui batas elastisitasnya. Hukum Hooke mengkaji
jumlah gaya maksimum yang dapat diberikan pada sebuah benda yang sifatnya elastis (seringnya
pegas) agar tidak melewati batas elastisnya dan menghilangkan sifat elastis benda tersebut.
Bunyi Hukum Hooke ialah “Jika gaya tarik yang diberikan pada sebuah pegas tidak
melampaui batas elastis bahan maka pertambahan panjang pegas berbanding lurus/sebanding
dengan gaya tariknya”.
Jika gaya yang diberikan melampaui batas elastisitas, maka benda tidak dapat kembali ke
bentuk semula dan apabila gaya yang diberikan jumlahnya terus bertambah maka benda dapat
rusak. Dengan kata lain, hukum Hooke hanya berlaku hingga batas elastisitas.
Dari gagasan tersebut dapat disimpulkan bahwa konsep hukum Hooke ini menjelaskan
mengenai hubungan antara gaya yang diberikan pada sebuah pegas ditinjau dari pertambahan
panjang yang dialami oleh pegas tersebut. Besarnya perbandingan antara gaya dengan
pertambahan panjang pegas adalah konstan. Fenomena ini dapat lebih mudah dipahami dengan
memperhatikan gambar grafik berikut ini.
26. 17
Gambar 1, menjelaskan bahwasanya jika pegas ditarik ke kanan maka pegas akan meregang
dan bertambah panjang. Jika gaya tarik yang diberikan pada pegas tidak terlalu besar, maka
pertambahan panjang pegas sebanding dengan besarnya gaya tarik. Dengan kata lain, semakin
besar gaya tarik, semakin besar pertambahan panjang pegas.
Pada Gambar 2, digambarkan bahwa kemiringan grafik sama besar yang menunjukkan
perbandingan besar gaya tarik terhadap pertambahan panjang pegas bernilai konstan. Hal ini
menggambarkan sifat kekakuan dari sebuah pegas yang dikenal sebagai ketetapan pegas.
Secara matematis hukum Hooke dapat dituliskan sebagai berikut.
F = k * Δx
Keterangan:
F = Gaya luar yang diberikan (N)
k = Konstanta pegas (N/m)
Δx = Pertambahan panjang pegas dari posisi normalnya (m)
Sehinga, dalam pengujian tarik, kekakuan pegas merupakan modulus elastisitas yang
digambarkan pada kemiringan sumbu pada kurva tegangan-regangan.
27. 18
2.4 Kajian Regulasi
2.4.1 Order 8110.42D
Order 8110.42D
Sub J
PMA Procedures Document
Complian
ce
Order 8110.42C Title Requirements PMAOH QP=
Manageme
nt
Approval
Purpose and
Administrative
Information
1.1. Purpose of this
order
Read 14CFR§21.303 for
Define the procedures
that FAA personnel
follow when issuning a
parts manufacturer
approval (PMA), How an
applicant applies for a
PMA and describe the
role of a designated
engineering
representative (DER) in
the PMA process
Read FAA order 8120.2
Production Approval
and Certificate
Management
Procedures, contains the
guidance for evaluation,
approval, adn certificate
management for the
production activities of
manufacturers and
therir suppliers who
produce parts under
PMA
1.2. Audience All FAA employees, ODA,
Designees
1.3. Where Can I find
This Order?
Read www.rgl.faa.gov
1.4. Cancellation FAA order 8110.42B, Parts
Manufacturer Approval
Procedures is cancelled
28. 19
1.5. Who needs a
PMA?
(a) General requirement
production of
replacement part needs
a PMA
production of
modification part would
need STC for approval. If
there is a major change
in modification, STC is
needed according to
14CFR§21.113. For more
information, see FAA
order 8110.4 about Type
Certification, for STC
procedures
(b) Getting a PMA for
TSO (Technical
Standard Order) Articles
The replacement part is
for the product, not the
articles.Installation of
this part may result in a
minor design change in
a TSO article yet meet
the product’s
airworthiness
requirements. The
installer of this part
required to place
modifier’s nameplate on
the article.
Replacement parts
approved under the
basis of identicality do
not change the article’s
design and do not
require a modifier’s
nameplate
Read FAA order8150.1
about TSO Program for
more details
1.6. What are the
Exceptions to PMA?
(a) Procedures and
Materials.
Any specific inspection
procedures, materials, or
processes (such as
29. 20
hardening, plating, or shot
peening) approved as part
of a PMA are valid only
for that particular part.
(b) ‘One-Time Only’
STCs.
Modifiers with these
design approvals may
manufacture, install
and return only one
product to service
without benefit of a
PMA
Otherwise we require
the applicant to get a
PMA or another
production approval
for the associated parts
when sold to others.
(c) Other Production
Approval Holders
(PAH).
Holders of a production
certificate, approved
production inspection
system, or TSO
authorization do not
need a PMA to produce
replacement parts for
their products or
articles under their
existing design and
production approvals.
If a supplier to a
production approval
holder (PAH) intends to
sell a part without
direct ship authority,
then that supplier
needs a PMA.
(d) Aircraft Owners or
Operators.
Owners and operators
may produce parts for
30. 21
installation on their own
product without a PMA
If an owner or operator
intends to sell a part
for installation on
another owner’s
aircraft, then that
owner or operator
requires a PMA.
(e) Air Carriers
Operating Under 14
CFR part 121 or 135.
Carriers may produce
parts for installation on
their own products
without a PMA as long
as they have accepted
instructions and
procedures in their
manual and comply with
14 CFR Part 43.
If air carriers intend to
sell a part to other
owners or operators,
then they need a PMA.
(f) Repair Stations.
:An FAA-certificated repair
station may fabricate a part
for installation on a type-
certificated product for
current and anticipated in-
house repairs. See AC 43-
18, Fabrication of Aircraft
Parts by Maintenance
Personnel. FAA do not
authorize separate sales of
these fabricated parts to
others.
(g) Producing and
Selling Standard Parts.
Production and sale of
standard parts for type-
certificated products do
not require a PMA.
However, a PAH may
buy standard parts,
31. 22
subject them to more
restrictive inspection
criteria and then assign
new part numbers.
These parts are no
longer standard parts. If
questions arise, contact
the certificating aircraft
certification office
(ACO), manufacturing
inspection district office
(MIDO), or both to
determine if the part
design meets the criteria
for standard parts.
(h) Importing
Modification and
Replacement Parts.
Under 14 CFR § 21.502,
we allow foreign
manufacturers to
export modification
and replacement parts
to the United States if
an applicable bilateral
agreement exists.
Other acceptable
replacement and
modification parts from
foreign countries with
bilateral agreements
include:
(1) Parts produced
by a foreign holder
of an FAA type
certificate (TC),
STC, or letter of
TSO design
approval (LODA)
on a foreign state
of design product ,
or
(2) Parts produced
by a foreign
manufacturer,
holding a
production
32. 23
approval from the
bilateral partner
Civil Aviation
Authority (CAA),
for U.S. State of
Design products
produced under a
licensing
agreement with
the design
approval holder.
(3) Parts that have
PMA from a
foreign
airworthiness
authority and are
recognized in a
bilateral
agreement with us.
1.7. Fabrication
Inspection System
(FIS)
FAA only issue PMAwith
FIS in US
PMA holder may have
suppliers manufacturing
facilities outside of US.
See order 8120.3 for its
description.
1.8. PMA and Older
Products
Approval of parts in
older products may
present potential
problems due to
incomplete design data,
out-of-production
products, and defunct
type certificate holders.
For these problems, we
still expect applicants
to:
send us enough
information to support
their claim that the
prospective PMA
design meets
applicable
airworthiness
standards. This
information should
33. 24
match the required
information listed in
chapter 2 in this order,
as appropriate to the
nature of the part.
Also, we still require
the applicant to show
the ability to produce
parts conforming to an
approved design.
We will allow some
changes in the
approved designs that
include later industry-
adopted standard
practices and
specifications that are
directly applicable.
1.9. The Roles of the
FAA and Aplicants
Approval of a PMA
application requires the
ACO to approve the
design and the MIDO to
approve the production
system. See appendix A,
PMA Process Flowchart.
1.10. Project Specific
Certification Plan
(PSCP)
The adaptive use of a
PSCP in PMA applications
will define and document
the approval plan between
an ACO and the applicant.
The plan should help us
issue a PMA quicker by
defining the design
approval criteria and
process. The ACO and
applicant should tailor the
plan based on the
complexity and criticality
of the proposed part. See
appendix B, Project
Specific Certification Plan,
for a PSCP template. Also
an ACO may use selective
parts of this template for
simpler, non-critical parts
34. 25
to summarize PMA
application data.
1.11. Deviations Engineering and
manufacturing personnel
in the FAA must follow
the procedures in this
order and Order 8120.2 to
ensure a standard process
for PMA.
We also must ensure
applicants are aware of
these procedures. The
Aircraft Engineering
Division (AIR-100)
coordinates and
dispositions any deviations
from this order.
1.12. Acronyms See appendix L, List of
Acronyms.
1.13. Definitions See appendix M,
Definitions and Terms.
What to Expect
from Applicants
2.1. Who Gets an
Application Letter?
Expect the applicant to send
a letter of application to one
of the following:
• The MIDO in the
geographic area of the
applicant’s manufacturing
facility, if the applicant is
applying for a PMA based
on an STC or identicality
by a licensing agreement.
See a sample letter to the
MIDO in Figure 9 of Order
8120.2, Sample FAA-PMA
Letter of Application to
MIDO. We list contact
information for all MIDOs
in appendix C, List of FAA
Manufacturing Inspection
District/Satellite Offices.
• The geographic ACO, if
the design approval basis is
identicality without a
license agreement or test
and computation. Find a
sample letter to the ACO in
35. 26
appendix D, Sample FAA-
PMA Letters of Application
to ACO. We list contact
information for all
geographic ACOs in
appendix E, List of FAA
Aircraft Certification/Field
Offices.
2.2. Content of
Application Letter.
Each letter will include
the manufacturing
facility’s name and
physical address.
Also, the letter will
identify the part under
consideration for PMA.
Other necessary
information in the
letter includes:
Identity of the type-
certificated product for
installation of the PMA
part. Note the make,
model, series, and (if
appropriate) serial
number of this product
as recorded on the
upper right-hand
corner of the product’s
type certificate data
sheet (TCDS).
For replacement parts,
the identity of the TC
holder’s part, including
the part’s name and
number. If known, the
applicant identifies the
drawing number and
revision level of this
original part.
Optional request for a
PSCP if the application
is for the design
approval of a complex
or critical part. Inform
applicants they can
submit a draft PSCP
using appendix B as a
36. 27
guide. Use of the PSCP
is at the reviewing
ACO’s discretion.
Statement that certifies
the applicant has an
established FIS that
meets requirements of
14 CFR § 21.303(h).
Brief description of the
basis for a design
approval.
Draft PMA
supplement.
2.3. Basis for Design
Approval.
a. Identicality by
Showing Evidence of a
Licensing Agreement.
The applicant sends
the appropriate MIDO
document from the TC,
STC, or TSO
authorization holder
authorizing use of their
data package.
Evidence of a licensing
agreement is not a
separate approval
method, but is a way to
show identicality. The
applicant uses this
evidence to show that
the data submitted are
FAA-approved and
identical to the original
part. For FAA purposes,
the licensing
agreement (in any
form) only needs to
authorize the applicant
to use the specified
type design data. See
FAA Order 8120.2,
Section 5, for more
information.
37. 28
TC holders prepare
“assist letters” for
applicants to send to
the MIDO. This practice
meets the
requirements of
showing evidence of a
licensing agreement
under 14 CFR §
21.303(c)(4). Find a
sample assist letter in
FAA Order 8120.2,
Figure 10.
PMA Assist Letter. In
the assist letter, the
licenser (usually a TC
holder or a PAH) may
identify critical parts to
aid MIDO processing of
the PMA application.
b. Identicality without
a Licensing
Agreement.
The applicant sends
the appropriate ACO a
statement certifying
that the design is
identical in all respects
to an approved design
The applicant also
provides the data
supporting the
identicality claim for
review and approval.
These data verify the
identicality in
dimensional and
material
characteristics, special
processes and coatings,
and test and
acceptance criteria.
Identicality without
38. 29
access to the original
design data is nearly
impossible for
sophisticated parts
with proprietary
processes or coatings.
Identicality to another
PMA is unacceptable
because 14 CFR §
21.303(c)(4) restricts
identicality to only
parts covered under
type certificates.
c. Test and
Computation.
The applicant sends
the ACO a data
package for review
and approval. This
data package describes
the part design, which
includes materials,
processes, test
specifications, system
compatibility,
maintenance
instructions, and part
interchangeability. The
package also includes a
test and substantiation
plan to show
compliance with
applicable
airworthiness
standards. See chapter
2, paragraph 5 for
more details about the
data package.
d. Supplemental Type
Certificate (STC).
The applicant
stipulates use of the
approved data from
39. 30
the STC and refers to
the STC number.
2.4. Draft PMA
Supplements.
After approving the
PMA, we will assign a
PMA and supplement
number. Use the
following samples as
guides for preparing
FAA-PMA
supplements:
Appendix F, Sample
FAA-PMA Supplement
for Identicality (Non-
Licensing Agreement) or
Test and Computation,
is a supplement based
on either identicality
without a license
agreement or test and
computation.
Figure 11 of Order
8120.2, Sample FAA-
PMA Supplement for
Licensing Agreement
and STC, is a
supplement based on
either an STC or
licensing agreement.
2.5. Applicant’s Data
Package.
Expect the applicant
to provide enough
information and
substantiation to meet
the requirements of 14
CFR §§ 21.303(c),
21.303(d)(2), and
21.303(f). This
substantiation shows
the part meets the
airworthiness
requirements in the 14
CFR part (or their
predecessor
regulations) for the
product affected by
installation of the part.
The data package can
include, but is not
40. 31
limited to, the
following:
a. Drawings and
Specifications.
Instruct applicants to
provide one copy of
the drawings and
specifications that
show part
configuration. These
drawings and
specifications should
address dimensions
and tolerances,
materials, and
processes that define
the part’s structural
strength and design
characteristics.
The required
information for critical
parts may include
routing sheets, tooling
requirements, process
sheets, material
handling and storage,
and inspection
requirements as
deemed necessary by
the FAA.
The applicant need
not provide readily
available industry and
government standards
or specifications
unless requested by
an ACO.
b. Inspection and Test
Procedures.
An applicant proposes
sufficient inspection
and test procedures to
affirm the
airworthiness of the
part design during its
manufacture. The
complexity and nature
41. 32
of the part sets the
scope of these
inspections and tests.
Critical parts may need
demonstration of their
manufacturing
processes, and
inspection and test
procedures before
approval of their
designs. These
processes and
procedures include
process controls,
finished product
performance, and
incoming material
controls. The data
usually include
elements of the
manufacturing cycle,
such as, raw material
purchase, evaluation
of material chemistry
and grain structure,
fabrication, melt
practices, forging
processes, machining,
surface treatments,
other material
properties, and
required inspections.
If the application basis
is identicality, then the
applicant includes the
necessary
manufacturing test
procedures to
demonstrate these
processes and
procedures.
If the application basis
is test and
computation, then the
applicant includes the
design and
42. 33
manufacturing test
procedures.
Test Results.
An applicant
provides test
results
commensurate
to the nature of
the part’s design
and its basis for
approval. Design
approval of
critical parts may
require the
applicant to
perform
additional
inspections and
tests.
If an applicant uses an
FAA-approved test
plan, we review and
approve the results.
The applicant sends us
the resultant
inspection and test
reports to
substantiate the
airworthiness of the
parts produced in
conformity with the
proposed design.
If the application bases
for the critical parts
are identicality, the
applicant provides
tests results that show
their manufacturing
methods and
processes are the
same as the original
parts.
If the bases for these
parts are test and
computation or STC,
then include both
design and
manufacturing test
43. 34
results in the data
package.
Safety Assessment.
Expect the
applicant to
submit a failure
mode and effects
assessment to
support
classification of
the proposed
part as either
critical or non-
critical. This
assessment
provides at a
minimum:
1. A qualitative
assessment of failure
modes and effects,
which notes the part
criticality and
considers:
Effect of
characteristics,
processes,
maintenance
procedures, or
inspections when
there’s a failure,
omission, or non-
conformance; and
Effect of operating
outside the part
application or
intended environment,
but with in the
product’s certification
limits.
2. Effect of part failure
on the next higher
assembly
and its
performa
nce.
3. Effect on the product
and its performance if
44. 35
the next higher
assembly fails.
Note: We evaluate this
assessment against the
applicable criteria in
14 CFR §§ 33.75,
29.602, 27.602,
25.1309, 23.1309 and
Policy for Propeller
Safety Analysis, Policy
No. ANE-2002-35.15-
RO of 30 October
2003. Go to the
Regulatory and
Guidance Library at
www.rgl.faa.gov to see
this policy
memorandum. If the
assessment shows
hazardous condition
from the effects of
failure cited in
paragraphs 2-5d (1)
through (3), then the
part is critical.
e. Design Change
Control.
Applicants
describe the
methods and
controls for
changes to the
part design.
They also
describe how to
integrate design
changes into the
manufacturing
process.
f. Airworthiness
Limitations.
Life-limited
parts identified
in the TCDS or
airworthiness
limitations
section require:
45. 36
a method for
accurately assessing
their fatigue life. This
method will include, at
least, appropriate
aspects of material
property distributions,
loads, frequency of
loads, mission profiles,
stress and
temperature
distributions, and
fatigue testing.
to assess the impact of
PMA parts on mating
life-limited
assemblies. Also parts
with replacement
times, inspection
intervals or related
procedures in an
airworthiness
limitation section of a
maintenance manual
need data that support
such.
Life Assessment.
Type certificate
holders often
assess the life of
parts that
operate in cyclic
load
environments.
This assessment
occurs during
certification
through test,
analysis, or both.
The PMA
applicant should
also evaluate the
life of the
proposed
replacement part
in the cyclic load
environment.
The evaluation
46. 37
may entail
fatigue life
analysis and
testing. The
results verify
part life and
support
instructions for
continued
airworthiness
(ICA) and a
continued
operational
safety (COS)
plan.
h. Other Data per 14 CFR
parts 34 and 36.
Address fuel
venting, exhaust
emissions and
noise standards
as appropriate.
i. Continued
Operational Safety
Plan.
(1)PMA holders
are responsible
for the
continued
operational
safety of their
designs.
Regardless of
part complexity,
PMA applicants,
should develop a
COS plan. The
critical nature of
a part sets the
scope of this
COS plan. This
scope addresses
problem
prevention, part
monitoring and
problem
response. The
specific
requirements for
tracking,
47. 38
reporting and
correcting
failures and
defects are in14
CFR §§ 21.3 and
21.99.
These
requirements
include at least:
Detailed records of all
aspects of the
manufacturing cycle,
A record-keeping plan
for the entire part life,
Methods to isolate
possible discrepant
part populations,
continually monitor
the service use of
parts, and review
design assumptions
based on service
experience,
Means for identifying
possible failure modes
and effects that
account for the part’s
operating environment
and interfaces to the
next higher assembly
and product, and
Methods and
resources used to
identify causes of
failures and to develop
corrective actions, and
means to carry out
these actions quickly
based on an
assessment of the
associated risks.
(2) The PMA
holder may
establish
procedures that
address COS
within their
quality system
48. 39
and note such in
a PSCP.
Part Marking.
The applicant provides
detailed part marking
information that
complies with 14 CFR §
45.15. Life-limited,
as well as parts having
an inspection interval
or related procedures
specified in the
manufacturer’s ICA,
require marking that
complies with 14 CFR §
45.14. Ensure these
markings do not
compromise the
airworthiness of the
part.
Installation Eligibility.
Expect the
applicant to
identify where
the part goes.
If the PMA is for parts
from an STC, the
installation eligibility
follows eligibility
requirements in the
STC. The PMA
supplement will note
the models affected by
the STC. A copy of the
STC is enough to show
eligibility.
If the part is simple,
non-critical, and not
based on an STC, then
an illustrated parts
catalog (IPC) alone
may suffice to show
eligibility.
Otherwise, the
applicant must:
Identify at least one
product for possible
49. 40
installation of the part.
Identify the product by
make and model,
series, and serial
numbers if necessary.
The applicant uses the
model information
found in the title box
on the product’s TCDS.
Show where the part
goes through a
combination of an IPC,
other supplements,
service bulletins, and
PAH repair manual
data.
Airworthiness
Directives (AD).
The applicant
identifies all
ADs and
unresolved
service
difficulties
involving the
original part
from the type
design.
Applicants must
show that:
their designs do not
produce the unsafe
conditions noted in
ADs and
avoid known service
difficulties of the
respective original
parts.
Maintenance
Instructions and ICA.
Applicants
furnish
instructions for
continued
airworthiness
per 14 CFR §
21.50. This
regulation
50. 41
requires a design
approval holder
to provide ICA
prepared in
accordance with
the airworthiness
requirements
applicable to the
effected product.
An applicant
either shows and
states that the
product’s ICA
are still valid
with the PMA
part installed or
provides a
supplemental
ICA for any
differences. Note
that products
with a TC
application date
before January
28, 1981 may not
have ICA.
Regulations
required ICA on
later products.
Also the
applicant
provides
supplemental
ICA when:
The PMA part
invalidates the
product’s ICA,
The design
approval
holder’s
instructions are
inadequate.
n. ICA for Life-limited
Parts.
If the PMA part
is life-limited,
the applicant
must submit a
supplement to
the limitations
51. 42
section of the
ICA per 14 CFR
§ 21.50. The
supplement
identifies the part
numbers and
associated life
limits.
2.6. Special
Requirements for Test
and Computation
Applications.
Applications submitted
on the basis of test and
computation should
specifically address:
a. Compliance with
Airworthiness
Standards.
Applications based on
test and computation,
either comparative or
general test and
analysis, must
demonstrate compliance
with applicable
airworthiness standards.
Find minimum
performance standards
in applicable TSOs and
airworthiness
requirements in the
following 14 CFR parts:
14 CFR part 23,
Airworthiness
Standards: Normal,
Utility, Acrobatic, and
Commuter Category
Airplanes.
14 CFR part 25,
Airworthiness
Standards: Transport
Category Airplanes.
14 CFR part 27,
Airworthiness
Standards: Normal
Category Rotorcraft.
14 CFR part 29,
Airworthiness
Standards: Transport
Category Rotorcraft.
52. 43
14 CFR part 31,
Airworthiness
Standards: Manned
Free Balloons.
14 CFR part 33,
Airworthiness
Standards: Aircraft
Engines.
14 CFR part 34, Fuel
Venting and Exhaust
Emission Requirements
for Turbine Engine
Powered Airplanes.
14 CFR part 35,
Airworthiness
Standards: Propellers.
14 CFR part 36, Noise
Standards: Aircraft
Type and Airworthiness
Certification. 11
b. Substantiation.
The applicant can prove
compliance with
applicable airworthiness
standards by
comparative or general
test and analysis.
Comparative test and
analysis substantiates
that the PMA part is at
least equal to the
approved original part.
Thus, the PMA part
meets the same
airworthiness standards
as the original part.
General test and
analysis shows the part
complies directly with
all airworthiness
regulations applicable
to the product affected
by part installation.
Tests support each type
of analysis and confirm
significant assumptions,
findings or conclusions.
Comparative Test and
Analysis. Expect the
53. 44
applicant to
demonstrate the
functional design of
the proposed part is at
least equal that of the
original TC, STC, or TSO
part.
This method
entails analyses
and tests of the
original and
proposed parts.
The criticality of
the part and the
complexity of its
design will dictate
the rigor of the
comparative
analysis and the
extent of testing.
Side-by-side
testing of
proposed and
original parts with
zero service time
under the same
procedures and
conditions
provide the
standard to
evaluate the
adequacy of the
replacement part.
The results of the
analyses and tests
will note any
differences and
provide sound
technical
justifications for
these differences.
Reverse
engineering of the
original part
supports a
comparative
analysis.
However,
comparison of the
respective PMA
54. 45
and product
designs may
suffice for simple,
non-critical parts.
General Test and
Analysis
The applicant
shows the part
complies directly
with the
product’s
airworthiness
requirements and
applicable TSO
requirements. For
example,
certification of a
proposed
replacement part
for an engine by
this method
would require
compliance with
all regulations of
14 CFR part 33
applicable to the
affected product.
Test Scope and Plan.
Part criticality and
complexity determines
the need, type, and
scope of testing to
support either a
comparative or general
analysis. Testing ranges
from functional to
component to flight.
This verifies the
performance and
durability of the part
for compliance with
applicable
airworthiness
standards. Simple, non-
critical parts may need
little or no testing.
Functional testing has
many purposes
55. 46
including:Verifying
design characteristics
(for example, vibratory,
coating effectiveness,
and so on),
Verifying part
interactions with the
next higher assembly
and affected systems
(for example, gears,
bearings, seals, blades,
and so on), and
Evaluating complex
parts made of intricate
components.
If the design warrants
testing, applicants
include a proposed test
plan and a draft
request for conformity
in their application to
the ACO. The test plan
identifies at least:
Test purpose,
Physical and functional
description of the test
article and setup,
Number of test units,
Unit identification,
Test conditions and
duration,
Test success and failure
criteria,
Test instrumentation
and data collection,
Test safety control, and
Control of test
procedures.
When appropriate, the
ACO issues the MIDO
the request for
conformity of the test
article and test setup.
The applicant conducts
the tests after
receiving FAA approval
of the test plan and
56. 47
MIDO approval of the
conformity. Either the
ACO or MIDO may
delegate to authorized
designees their
respective witnessing of
testing, teardown
inspections, and
conformity inspections.
Then, the applicant
sends a test report to
the ACO that includes
an analysis of the test
results, the post-test
teardown inspection
results, and a
determination of
adequacy to the
applicable
airworthiness or test
standards.
Flight Testing.
Any flight tests
that require an
FAA test pilot or
designee will
need a prior
approved type
inspection
authorization.
Test Standards. Use
one of the following
test standards to
measure the adequacy
of the PMA part:
Comparative Testing.
They use parts from the
TC or STC holder that
have zero service time.
They also test the TC or
STC part under the
same procedures and
conditions as the
applicant’s part.
General Testing. They
verify the part meets
the applicable
57. 48
airworthiness
requirements of 14 CFR
and if applicable, the
TSO performance
requirement.
Other tests deemed
acceptable by the FAA.
c. Reverse
Engineering.
An applicant’s
challenge entails
selecting the processes
and techniques that are
appropriate to the part’s
complexity.
Dimensional
comparison by itself is
usually inadequate to
characterize and
compare a new original
part to a proposed
replacement. However,
reverse engineering
may duplicate simple
parts. Complex parts
need other
substantiating
information to show
equivalency between
original and PMA parts.
The applicant usually
considers the following
when using reverse
engineering:
Sample Size.
Typically these
samples are new,
unused parts from
approved and
traceable sources
(for example,
purchase orders,
FAA
airworthiness tag,
and so on). The
sample size varies
with design
complexity and
key attributes that
58. 49
define a part. Use
enough samples
to correctly
represent the
essential
characteristics of
a design. These
essential
characteristics
include nominal
dimensions,
tolerances,
material
properties, and
fabrication
processes.
Sampling used
parts may provide
some
characteristics
that do not
deteriorate during
use, such as
material
composition,
grain size and
grain flow. Select
samples from
separate lots,
billets, production
runs or other
criteria that vary
in the population.
If production
tracking data for a
part is unknown,
obtain parts from
different sources
at different times
to capture
potential sources
of variability.
Ensure applicants
substantiate the
validity of this
approach and get
concurrence from
the appropriate
ACO. Testing
may include more
59. 50
samples to show
equivalency
between a new
original and the
PMA part.
Dimensional
Tolerances.
Variations in the
sample
measurements
and accepted
engineering
practices
determine the
tolerances in part
dimensions. The
resulting
tolerances for the
PMA part should
not exceed the
minimum and
maximum
dimensions
measured on the
sampled
approved parts.
Exceeding these
limits requires
further
substantiation.
Materials. Various tests
and documentation
from the PAH or
supplier define the
material composition of
a part. Usually the PMA
part materials are
equivalent to the
materials for the
original part including
the base part, any
subparts, added welds,
and coatings. However,
an applicant may
propose and
substantiate alternate
materials and
processes that are at
least equivalent. A
60. 51
qualified laboratory can
provide thorough
destructive testing for
at least the following
information:
Composition of each
material in the part,
Material properties
(that is, strength and
fatigue characteristics,
hardness, grain
structure, and so on),
Form of material (that
is, casting, forging, bar
stock, sheet, and so
on), and
Use of special
processes (that is,
nitriding, heat treat,
shot peening, and so
on) and resulting effect
on material properties.
Weight and Mass
Properties.
The mass
properties of a
part are often
significant to its
function and
impact on the
associated
product. To
assess the effects
on the next higher
assembly and
product, the
reverse
engineering
process compares
these properties.
This assessment
accounts for
weight
differences
between the
proposed part and
the original part
to ensure the
61. 52
absence of
detrimental
effects. For
example, a small
weight increase in
compressor
blades can affect
disc life.
2.7. Identicality by
Other Than Licensing
Agreement.
If the PMA basis is
identicality without a
license agreement, expect
the applicant to show every
aspect of the submitted
design is identical to a TC,
STC, or TSO part
including manufacturing
processes. Common areas
of identicality include
materials, dimensions,
tolerances, finishes,
assembly, and special
processes. However,
allowable changes may
include standard industry
practices, processes, and
specifications that were
updated universally. Also,
the applicant submits a
safety assessment per
chapter 2, paragraph 5d
with the substantiation data
package.
2.8. Part Marking
Requirements.
Title 14 CFR § 45.15
sets the marking
requirements for PMA
parts installed on TC
and STC products and
TSO articles. These
markings are permanent
and legible. They
identify the part as
FAA-PMA. They also
identify the
manufacturer, part
number, and the
affected type-
certificated products. If
the part basis is an STC,
then the shipping
62. 53
document refers to this
STC and identifies
installation-eligible TC
products.
a. Marking Critical Parts.
Critical parts also
follow the
marking
requirements in
14 CFR § 45.14.
This requirement
adds a serial
number or
equivalent to the
part markings.
The method for
marking a critical
part is essential
design data that
the FAA reviews.
The applicant
ensures and the
ACO confirms
the marking
location and that
the process does
not degrade
airworthiness. To
do this, we
require
applicants to
define the
marking location
and method on
their drawings.
b. Marking an Assembly.
Applicants apply
PMA part
markings
required by 14
CFR § 45.15 to
the top-level
assembly of the
approved
replacement or
modification
part. We do not
require applicants
to mark
subassemblies or
63. 54
individual detail
parts. For
example, if the
top-level
assembly is a
hydraulic pump,
mark this
assembly
accordingly.
Marking the
detail parts of the
pump is optional
unless production
of these parts
occurs under
separate PMAs.
When PMA
holders separately
sell detail parts
for installation in
their approved
assembly, they
note the
information
required by 14
CFR § 45.15 on
the accompanying
shipping
documentation.
The shipping
documentation
for individual
detail parts of a
PMA assembly
must contain the
information
required by §§
45.15(a)(1)
through (3) and
must identify the
detail parts as a
subcomponents of
the PMA
assembly.. The
PMA holder’s
design data may
contain the
marking
information for
detail parts of the
64. 55
assembly. This
provides a means
of tracing the
individual detail
parts to their
related PMA
assemblies.
c. Part Numbering.
If the PMA part
replaces an
original part, the
applicant assigns
a part number
that distinguishes
the PMA part
number from the
corresponding
TC holder part
number. Adding
a prefix or suffix
to the TC holder’s
part number is
enough as long as
the prefix or
suffix does not
compromise the
TC holder’s part
marking
practices. The
applicant may
also use a prefix
or suffix to satisfy
14 CFR §
45.15(a)(2)
requirements for
marking the part
with a name,
trademark, or
symbol. This only
applies if the
prefix or suffix is
consistent across
the applicant’s
product line.
Also, each part
bears “FAA-
PMA” to meet
another 14 CFR §
45.15
requirement.
65. 56
1. Supplier Numbers.
Some
applicants
are
suppliers to
PAHs.
Often these
PAHs use
the supplier
part
numbers in
their
approved
designs.
When these
suppliers
later apply
for a PMA,
they may
continue to
use their
original
part
numbers
with the
added
marking
requiremen
ts of 14
CFR §§
45.15(a)(1)
and (2).
These
added
requiremen
ts entail
permanentl
y marking
the part
with “FAA-
PMA,” and
the name,
trademark,
or PMA
holder’s
symbol.
2. Parts Manufactured
Under License. When
the PMA basis is
identicality by showing
66. 57
evidence of a licensing
agreement, the PMA
part may have the
same number as the
type-certificated part.
However, we require
the applicant to meet
the requirements of 14
CFR §§ 45.15(a)(1) and
(2) by permanently
marking the part with
“FAA-PMA” and the
PMA holder’s name,
trademark, or symbol.
d. Parts Impractical to
Mark.
If we find the part
too small or
impractical to
mark all the
information on it,
then an attaching
tag or container
label must have
the missing
information.
Often the number
of eligible type-
certificated
products is too
long to include
with the part.
Since the list is
likely to change,
a tag or label on a
container may
refer to the
applicant’s
publicly available
part eligibility
information. Title
14 CFR §
45.15(b) requires
making the
installation-
eligibility
information
contained in a
manual or
67. 58
catalog readily
available.
Providing a
manual or catalog
via the Internet
meets the intent
of “readily
available.”
However, access
to the Internet is
not universal. The
PMA holder must
have an
alternative means
of providing the
manual or
catalog.
e. Marking a PMA Part on
a TSO Article.
Markings for a
PMA part that
goes on a TSO
article follows the
same protocols.
Title 14 CFR §
45.15 requires
the holder to
mark parts as
prescribed per
the approved
design. The
installation
eligibility in these
markings notes
the name and
model of each
applicable type-
certificated
product. To meet
the requirements
of 14 CFR §
45.15, record the
PMA
installation-
eligibility
information (that
is, A310-200
series, B737-300
series, and so on)
on the part. Do
68. 59
not list the TSO
identification
information (that
is, TSO-C149,
TSO-C63C, TSO-
C85A, and so on).
However, if an
applicant holds a
TSOA on the
same part, then
mark the part
with both PMA
and TSO
markings.
2.9. Use of Designees. Designees expedite the
review and approval process
for PMA. Holders of ODA
perform many of the same
functions as ACOs
including review of part
design, verify conformity,
issue supplements, etc.
Individual designees
approve data within their
authorized limitations in
support of the PMA
process. See Order 8100.15,
Organization Designation
Authorization Procedures
and Order 8110.37,
Designated Engineering
Representative (DER)
Handbook, as well as,
chapter 5 of this order for
more information.
Applicants without ODA
will identify the names and
contact information of
participating DERs to their
responsible ACO in their
application letters and
PSCP, as applicable.
2.10. Establishment
of the FIS.
Title 14 CFR § 21.303(h)
requires the applicant to
set up and maintain a
FIS. See Appendix 2 of
Order 8120.2 for more
details.
69. 60
2.11. Responsibilities
of PMA Holders after
Approval.
Report Failures,
Malfunctions, and
Defects.
PMA holders
must comply with
14 CFR § 21.3.
The PMA holder
creates a
procedure to
report to the FAA
any failure,
malfunction, or
defect of a PMA
part that left its
quality control
system. At a
minimum, this
reporting
requirement
applies to failures,
malfunctions, or
defects that may
result in one of the
occurrences listed
in 14 CFR §
21.3(c). The data
package includes
this procedure in
the COS plan. We
review this
procedure during
the design
approval portion
of the PMA.
Maintain FIS.
We require PMA
holders to
maintain an
accepted FIS to
comply with 14
CFR § 21.303.
Holders should
report to the
MIDO any
changes in their
FIS that may
affect the
inspection,
conformity, or
airworthiness of
70. 61
their parts before
implementing
these changes.
The production
approval number
issued by the
MIDO is evidence
of an accepted
FIS.
Designees. After we
issue a PMA,
the holder can
apply for
appointment of
qualified
individuals as
designated
manufacturing
inspection
representative
(DMIRs) or
ODAs per 14
CFR part 183.
See Order 8100.8,
Designee
Handbook, and
Order 8100.15 for
more details.
Additional Part or
Installation Approvals.
A PMA holder
can apply for
additional
approvals for
other parts or
installations on
other products.
These applications
follow the
applicable
requirements of
this order. The
holder still
complies with
design approval
requirements in 14
CFR § 21.303 and
marking
requirements in 14
71. 62
CFR §
45.15(a)(4).
When the holder uses
an already accepted
production system, the
ACO still approves the
design of the additional
part and the MIDO
conducts an optional
review of the holder’s
FIS. The MIDO reviews
the holder’s FIS if
production of new parts
significantly increases
the holder’s scope of
operations or demands
greater manufacturing
abilities.
Holders can apply for
additional installation
eligibility for an
approved part on other
products. They still
show the part meets
the airworthiness
requirements of these
products and
demonstrate an
understanding where
the part goes. See the
applicable procedures in
this chapter, paragraph
5. Also expect the
holder to submit the
information about any
associated ICA found in
this chapter, paragraph
5m. After design
approval and FIS review,
the ACO will sign and
the MIDO will issue a
PMA supplement that
adds the new parts or
installations to the
original approval.
Type certificate holders
and PAHs often use
72. 63
existing parts in
newer/later models of
their products. PMA
holders of
corresponding
replacements for these
parts usually cite an IPC
that notes these
common parts in the
newer models. For
simple, non-critical
parts, an unaltered IPC
from these holders may
be enough to show
eligibility. However, for
critical or complex
parts, additional
installation eligibility for
an approved part
should follow the
procedures in this
chapter, paragraph 5k.
Design Changes.
PMA holders may
introduce changes to
their designs. Minor
changes are those
having no appreciable
effect on the approval
basis. All other changes
are major. Holders need
prior ACO approval
before implementing
major changes.
However, we and PMA
holders may agree upon
the manner and
timeframe for the
approval of the minor
changes. One manner
entails the holder
providing sufficient
information to affirm
the change is minor.
This information
includes a list of parts
by name and number,
73. 64
their latest FAA-
approved drawing
revision with date of
approval, and a brief
description of each
change. The applicant
and ACO often record
the agreement in
writing for clarity. Some
acceptable methods for
approving minor
changes in the designs
of parts are:
Periodically send a list
of changes and
descriptive or
substantive data to the
ACO,
Designee (DER) or ODA
approve the minor
changes,
Use the change control
process in the approved
fabrication inspection
system,
Holder of the design
approval for the original
part approves changes.
Any changes to critical
parts and major
changes to other PMA
parts require prior
approval by the
appropriate ACO. This
approval occurs before
implementing any
change and in the same
manner as original PMA.
Also, we expect the
PMA holder to show the
effects of this change on
the next higher
assembly and
associated product in a
revised safety
assessment.
74. 65
If the basis for the PMA
was identicality by
showing evidence of a
licensing agreement,
the holder may
implement the same
minor changes accepted
by the FAA on an
original TC or STC part.
In this case, PMA
holders have the
responsibility to keep a
document trail linking
their change to the
revised design of the
original design approval
holder. When the
licensing agreement
ends or does not
mention change control
authority, the PMA
holder submits design
changes to the FAA for
approval. The ACO
having jurisdiction over
the PMA holder
approves those later
changes.
Note: Part
manufacturers must get
their own TSO
authorization if the
installation of a
replacement part results
in a major design
change to a TSO article.
A new TSO
authorization is
unnecessary if you
install a PMA part under
14 CFR part 43 or other
applicable airworthiness
regulations. See Order
8150.1 for more details.
Relationship Change in
a License Agreement.
The PMA holder may
not produce parts when
75. 66
a change in its
relationship to the
design approval holder
prevents them from
meeting their PMA
responsibilities.
Aircraft
Certification
Office (ACO)
Responsibilities
1. General
Responsibiliti
es.
The geographic
ACO has several
responsibilities for
PMA applications.
The project
engineers at these
offices make
findings of
compliance with
applicable
regulations. ODA
units have nearly
the same
responsibilities
and authorities for
approving the
design of
replacement parts
as ACO
personnel. Both
the ACO and
ODA unit follow
the same process
that show
prospective parts
meet the
airworthiness
requirements of
their respective
products.
However, ODA
holders must
develop their own
procedures that
follow our design
approval process
in PMA. The
ODA
responsibilities,
authorities and
limitations are in
Chapter 13 of
Order 8100.15.
76. 67
The project
engineer at the
ACO has the
following
administrative
and technical
responsibilities:
Accepts Application.
Confirms Location of
Manufacturer.
Manages Design
Review and Approval.
Reviews Engineering
and Test Data.
Seek FAA
expertise
from other
ACOs,
directorates,
and Chief
Scientific
and
Technical
Advisors
(CSTA) as
needed.
Dependent
on the
nature and
complexity
of the part:
Verify safety
assessment.
Verify acceptable
service history of the
original part.
Verify the eligibility for
installation on type-
certificated products.
Verify the PMA
application uses
airworthiness
requirements applicable
to the type-certificated
product on which the
PMA part is installed.
77. 68
Verify the design data
are adequate to
produce the part.
Review all differences
between the proposed
and original parts.
Assess the technical
justification for these
differences and
associated impacts on
the next higher
assembly and product.
For example, weight
and other mass
properties can influence
vibratory response and
performance of rotating
components. Also,
assess the applicant’s
analysis of part weights
and associated effects
from any weight
differences on an
assembly and
associated product.
Assess requests by
applicants for
conformity inspections.
Engage the MIDO when
conformity deemed
necessary.
Review and approve
test plans and reports.
Find the applicant’s
substantiating data
show compliance with
applicable airworthiness
standards.
Verify suitability of
applicant’s COS plan.
3.2. Applicant
Approaches.
Applicants may combine
comparative and general
analyses in their test and
computation approaches to
show compliance with
airworthiness standards.
78. 69
3.3. Review of
Applicant’s Abilities.
Review each application
with the MIDO as needed.
Coordinate conformity
inspections when part
criticality, complexity, an
applicant’s history or other
factors warrant. Confirm the
applicant’s ability to do the
following:
• Conform materials to
specifications in the
design;
• Conform the part to the
design drawings;
• Apply the manufacturing,
construction, and assembly
processes specified in the
part’s design (see 14 CFR §
21.303(f)(1) through (4));
• Process approval of major
and minor design changes;
and
• Track and report failures,
malfunctions, and defects
per the requirements in 14
CFR § 21.3.
3.4. Coordination with
Certificate
Management ACO
(CMACO).
If the part basis is
identicality, confirm with
the CMACO (and MIDO
when appropriate) if the
applicant’s manufacturing
processes are identical to
the part produced under the
TC or STC. Also some
product directorates require
coordination of approvals
for parts that may affect
critical parts. Consult with
your directorate for specific
guidance on the
coordination method and
scope.
3.5. Verification of
Installation Eligibility.
a. A manufacturer’s IPC
offers information about
installation eligibility,
but the IPC is usually
not FAA-approved.
Consider using the IPC
with other data like
79. 70
purchase orders from the
PAH, service bulletins,
maintenance manuals, a
technical publications
index, or a master
drawing list. Other
acceptable
documentation is a
combination of the
following:
FAA airworthiness
approval tag (FAA Form
8130-3),
Other PMA
supplements, and
“Weight of evidence”
evaluations using
enough information
from various sources to
show eligibility.
b. Accept use of the IPC
alone as a means for
verifying installation
eligibility on non-critical
parts. When the IPC is
the sole means of
verifying installation
eligibility, confirm the
authenticity of that IPC.
c. If the application lacks
documentation from the
TC or TSO authorization
holder (or other FAA-
approved data), then the
ACO may consider other
evidence from the
applicant. To verify
installation eligibility,
check other documents
including the type
design’s master drawing
list.
3.6. Service History
Considerations.
Review of the service
history is essential when a
part is critical. Follow the
guidelines below if a TC or
STC part has a potential
unsafe condition and the
80. 71
proposed PMA part has a
similar design:
a. Reject the PMA
application if an existing
AD removes the associated
TC holder’s part from
service immediately or in
the future.
b. Consider delaying the
processing or rejecting the
PMA application if we are
discussing or developing an
AD to remove the TC
holder’s part from service.
c. If the TC holder’s part is
under investigation for an
incident or accident, delay
processing the PMA
application until the part is
cleared.
d. Reject the PMA
application if an AD calls
for repetitive inspections
without setting a
terminating corrective
action (for example,
modification or replacement
of the part). Also, reject the
PMA application if the
intent of repetitive
inspections is to detect
potential failures before
reaching a published service
life. We want and prefer a
terminating corrective
action. Issuing a PMA to
produce and distribute parts
of a substantially identical
design only complicates and
prolongs the unsafe
condition.
e. If a part is not identical or
substantially identical to the
TC holder’s part, determine
whether installing the
applicant’s part creates an
unsafe condition.
f. If the original part has a
service bulletin to remove it
from service, we may still
81. 72
issue a PMA. A service
bulletin alone is not enough
to disapprove a PMA.
g. If the part is having
service difficulties and the
FAA is ACTIVELY
pursuing corrective action
(that is, a design change per
14 CFR § 21.99) with the
TC holder, reject the
application for PMA.
h. Consult the FAA Service
Difficulty Reporting System
and the TC product support
database for service
difficulties of a critical part.
3.7. Life-Limited
Parts
Substantiate any life-
limited parts per applicable
paragraphs in chapter 2,
paragraph 5 in this order.
The required
substantiating data must
include fatigue tests on
components produced by
the applicant. Ensure the
applicant notes the PMA
life limits in the part’s
ICA.
3.8.Special
Considerations—
Identicality without A
License Agreement.
Design approval based
on identicality entails
the applicant showing
that the PMA part
design is identical to the
TC part design in
dimensions, tolerances,
materials, processes,
and specifications.
Some part designs
contain features that
have no influence on
airworthiness or the
next higher assembly.
These features may
include color, tighter
tolerances, and so on.
The PMA design may
deviate in these features
without affecting
82. 73
identicality. Also, the
applicant’s design need
not conform to the latest
revision level of the TC,
STC or TSO
authorization holder’s
drawing if we
determine that the
previously approved
parts are still eligible
for installation on the
listed product models.
a. Limitations of Reverse
Engineering.
Take special care
in evaluating
identicality based
on reverse
engineering.
Reverse
engineering is
one way to
develop the part’s
design. However,
reverse
engineering a
part will not
normally produce
a design that is
identical to a
type-certificated
part. The
applicant is
unlikely to show
that tolerances,
processes, and
manufacturing
specifications are
identical. The
rigor and scope
of the
substantiating
data should
reflect the degree
that the design is
identical. The test
and computation
method is the
alternative to
identicality. The
83. 74
applicant shows
that the proposed
design complies
with the
applicable
regulations.
b. Identicality Not Found.
See appendix G,
Sample Design
Rejection Letter.
However, PMA is
still possible if
the applicant
shows through
tests and
computations that
the part meets all
applicable
airworthiness
requirements per
14 CFR §
21.303(f)(1)
through (4).
c. Design Changes.
Limit design
changes on PMA
parts based on
identicality
without a license
agreement. Limit
these changes to
part marking,
updated
specifications,
and so on.
3.9. Special
Considerations—
Test and
Computation.
a. Safety Assessment.
Use available FAA
expertise to aid in
evaluating these
assessments (see
chapter 2, paragraph
5d).
b. Reverse Engineering.
Review the applicant’s
data to confirm
equivalency to the
original design. Ensure
84. 75
the design of the
duplicate part defines
dimensions, material
properties (for
example,
microstructure,
chemical
composition), special
processes (for
example, welds, heat
treat, coatings), and
continued
airworthiness
requirements. Ensure
that the applicant has
adequately captured
potential sources of
variability in both the
original design and the
duplicate part.
Potential sources of
variability include
processing
characteristics (lots,
billets, etc.), material
supply vendor, and
other such
considerations.
c. Test Plans and
Reports. Review any
test plans and results
that show the part is
equivalent to the
original or complies
with applicable
airworthiness
standards. Also, verify
that the results
confirm the
functionality of
complex parts in their
assemblies. Request
additional testing as
needed to confirm
equivalency to the
85. 76
original part and
impact on the
original’s ICA.
d. ICA or Maintenance
Instructions. Review
the applicant’s
proposed ICA or
maintenance
instructions and
coordinate with the
appropriate aircraft
evaluation group
(AEG) of the Flight
Standards Service. If
the applicant proposes
that no new ICA or
maintenance
instructions are
necessary, review the
applicant’s
substantiation for that
position. If the ACO
agrees that the TC or
TSO authorization
holders’ instructions
are applicable, note
such on the
notification letter. See
appendix H, Sample
Notification Letter.
e. Minor Design
Changes.
(1) Title 14
CFR
§21.95
stipulates
that
approval of
minor
changes
may occur
in a
manner
acceptable
86. 77
to the
administrat
or. PMA
holders are
responsible
for
properly
assessing
the
magnitude
and impact
of changes
on their
designs.
We
approve
these
minor
changes
when we
accept
their lists
and
supporting
assessment
s of minor
changes at
periodic
intervals.
This
approach
places the
responsibil
ity for
safety of
the design
change on
the PMA
holder. We
view a
design
change as
major in
PMA when
it has an
appreciable
affect on
the basis of
87. 78
its
approval.
(2) The
certifying
ACO sets
the manner
and
interval for
approving
minor
changes to
the design
of a PMA
part. One
manner is
through a
written
agreement
with the
PMA
holder to
periodicall
y provide a
list of
minor
changes to
the ACO.
The holder
provides
sufficient
informatio
n to affirm
the change
is minor.
This
informatio
n lists the
parts by
name and
number,
their latest
FAA-
approved
drawing
revision
with date
of
88. 79
approval,
and a brief
description
of each
change.
The ACO
keeps a
record of
these
approvals
and
provides
documenta
tion of
such to the
PMA
holder. As
noted in
their
handbook,
we may
authorize
designees
to approve
these
changes.
3.10. Evaluating the
Drawing Package.
.
Consider the following
areas when evaluating
any data package:
a. Manufacturing and
Process Specifications.
Manufacturing
procedures and process
specifications may
affect the part’s
airworthiness. If the
applicant’s detail
drawings refer to a TC
holder’s process
specifications, then the
applicant must submit
these specifications.
Coordinate with the
CMACO as necessary
to determine how these
specifications affect the
design’s airworthiness.
89. 80
b. Source Control
Drawings. Carefully
review source control
drawings to determine
if the applicant has
proper control over the
part’s configuration
and manufacture.
Ensure the applicant
submitted all
applicable detail
drawings and
specifications.
c. Drawing Notes.
Establish that the
applicant’s data are
enough to produce
conforming parts before
issuing engineering
approval. Evaluate each
applicant’s ability to
produce the part on a
case-by-case basis. If
the applicant cannot
provide this
information, use the test
and computation
method. Pay particular
attention when the
design approval
holder’s drawings or
specifications used to
make a finding of
identicality have notes
stating:
Parts supplied to this
drawing shall be in
strict accordance with
samples (first articles)
approved by (name of
applicant) engineering
department unless
prior written approval
is given to subsequent
change.
90. 81
Source approval is
required for raw stock
through total
fabrication.
This drawing
represents a critical
item and must
successfully complete
substantiation tests
and be approved by
engineering.
Other similar
statements implying
special source selection
criteria
3.11. Conformity
Inspections.
an inspection of the first
article by the applicant may
demonstrate conformity for
simple, non-critical parts.
Coordinate with the
responsible MIDO to
schedule timely inspections.
Then the MIDO or
appropriate designees
determine that the part
conforms to its drawings,
specifications, and special
processes. Use FAA Form
8120-10, Request for
Conformity, or FAA Form
8110-1, Type Inspection
Authorization, to request an
inspection.
3.12. Design
Approval.
Perform the following
steps after finding that the
applicant showed
compliance with the
applicable airworthiness
requirements:
a. Keep the
submitted data
package for ACO
project files or get a
written agreement
with the applicant
91. 82
for on-demand
access except as
noted in paragraph c
below.
b. Send the applicant
a letter that confirms
you sent the
application to the
MIDO for more
processing. See
appendix H for a
sample of a
notification letter.
Adjust this sample to
comply with office
guidelines on format
as needed, but ensure
the revised format
contains the same
information as the
sample.
c. Return previously
FAA-approved
design data that the
applicant voluntarily
submitted. In the
official ACO files,
list this previously
approved data that
supported a finding
of identicality.
d. Send copies of the
unnumbered and
signed PMA
supplement and the
applicant’s letter to
the responsible
MIDO. If the
responsible MIDO is
remotely located,
send advanced
electronic copies of
these documents to
expedite processing
of the PMA.
3.13. Revising the
PMA Supplement.
Some offices issue a revised
supplement with
92. 83
corrections. Then, they send
the revised supplement to
the PMA holder and request
return of the original
incorrect supplement.
Usually we need an
amendment to the
supplement when an
applicant adds eligibility to
the supplement. AIR-140
desires the updated
supplements in Microsoft
Word table format with a
note stating the ACO or
MIDO action (for example,
correction, revision,
amendment, superseding,
cancellation or change of
address).
3.14. Non-
Compliance.
No requirement.
Manufacturing
Inspection
District Office
(MIDO)
Responsibiliti
es
4.1. PMA Activities. Refer to FAA Order
8120.2, Section 5 for
MIDO responsibilities in
PMA.
Designated
Engineering
Representativ
es (DER) and
Organization
Designation
Authorization
(ODA)
5.1. DER Roles in the
PMA Process.
No requirement
5. 2. Test and
Computation.
No requirement
5.3. Identicality
Provisions.
Identicality is unique to
PMA. A DER requires a
special FAA authorization
to make this finding. The
DER adheres to the
provisions in Order 8110.37
when conducting PMA
93. 84
activities for findings of
identicality. See appendix
K, for an example of a
completed FAA Form 8110-
3 for Identicality.
5.4. Findings of
Identicality.
Designees verify the
following for findings of
identicality:
• The TC, STC or TSO
authorization data listed on
Form 8110-3 is approved
type design data for the
indicated product models.
• The stated eligibility of
the PMA is appropriate.
• No mandatory corrective
actions are necessary in the
part.
• No serious unresolved
service difficulties will
make the part ineligible for
installation.
5. ODA Role in the
PMA Process.
No requirement
Tabel 2 Order 8110.42D
2.4.2 AC No:21-55
Beban yang tidak semestinya merupakan ketentuan yang dibuat FAA terhadap aktivitas
yang diajukan di luar US, yang membutuhkan bantuan FAA, yang melampaui sumber daya
FAA yang tersedia. Sumber daya terdiri dari personil atau komitmen waktu. Jika FAA
menentukan sebuah proposal akan menyebabkan beban yang tidak semestinya, proposal
tersebut akan ditolak.
Selain itu, FAA harus mempertimbangkan variasi sertifikasi luar negeri dikarenakan
perbedaan tipe aktivitas, hubungan bilateral, lingkup proyek, dan kondisi negara/yurisdiksi
dimana fasilitas terletak, di atas variabel lainnya.
2.4.3 AC 21-09 Amdt 0
Berdasarkan dokumen DKUPPU AC 21-09 Amdt 0 tertanggal 28 Februari 1998, mengenai
Certification Procedures for Products and Parts. Pada AC ini dibahas mengenai PMA, dimana
persyaratan-persyaratan dalam memperoleh PMA diantaranya;
Surat Direktorat Jenderal Perhubungan Udara-PMA akan dikeluarkan setelah
Direktorat Jenderal Perhubungan Udara menentukan bahwa pemohon memenuhi
persyaratan kelaikan udara dari Peraturan Keselamatan Penerbangan Sipil yang
berlaku.
94. 85
Pemohon mengajukan pernyataan yang menyatakan bahwa ia telah mendirikan
sistem inspeksi fabrikasi yang dibutuhkan oleh CASR 21,303 (d). Pernyataan
sertifikasi dapat diserahkan kemudian, setelah dari submittal dari data desain
diperlukan dalam CASR 21,303 (c).
Setelah penerbitan surat PMA, Direktorat Jenderal Perhubungan Udara akan
melakukan inspeksi periodik dari fasilitas pabrik, yang mungkin termasuk
pemasok, untuk menentukan bahwa sistem inspeksi fabrikasi sedang dipertahankan
seperti yang dipersyaratkan oleh CASR 21,303 (h). Inspeksi periodic ini akan
menjadi tanggung jawab district office.
Juga dibahas mengenai additional approval, yaitu apabila suatu perusahaan telah menerima
design approval untuk additional parts, maka dapat ditambahkan dalam PMA letter dgn
prosedur yang sama. PMA letter dapat dibuat untuk modifikasi dari new used part, asalkan
100% conformity, dan manufacturer dapat memenuhi persaratan DMIR untuk mendapatkan
airwortiness approval tags ketika dibutuhkan untuk mengekspor parts.
Desing approval meliputi dua hal;
Data Requirement yang diputuhkan untuk PMA
Bukti licensing agreement dengan STC dan/ atau TC holder, lengkap dengan data desain yang
tercakup dalam perjanjian
Detailed Drawaing dan data yang menunjukkan bahwa part tersebut memenuhi persyaratan
kelaikan udara
Data yang menyatakan 100% conformity.
Part numbering, dapat dilakukan sama dengan part number manufacturer
Part yang dibuat harus memnuhi Airworthiness Requirements - CASR 21.303(d).
Part yang dibuat harus memenuhi Fabrication Inspection dan System Description, yang
mengikuti poin-poin dari CASR 21.303 (h) 1 sampai 9.
2.4.4 CASR 21 Subpart G
Pada CASR 21 Subpart G membahas mengenai production certificate. Persyaratan awal
untuk mengajukan production certificate adalah apabila applicant memiliki TC, STC, dan/ atau
hak khusus melalui licencing agreement. Setiap applicant harus dapat menunjukkan dokumen
yang membuktikan bahwa perusahaan dapat menjamin pemenuhan ketentuan yang berlaku.
Selain itu, setiap applicant harus memiliki quality system yang menjamin confortmity setiap
produk dan artikel denga desain yang telah disetujui. Quality sytem ersebut melipui;
Design data control, untuk mengontor data agar memastikan bahwa hanya data
yang benar dan disapproved yang digunakan.
Document Control, mengontrol dokumen untuk memastikan bahwa hanya
dokumen yang benar dan disapproved yang digunakan.
Supplier Control
Manufacturing process control.
Inspeting and testing