This document provides design requirements for lacing and battening systems used in steel structural elements. It discusses two types of lacing systems - single and double. It outlines 9 design requirements for lacing per Indian code IS 800, including angle of inclination, slenderness ratio, effective length, width/thickness, transverse shear force, strength checks, and end connections. It also discusses 7 design requirements for battening systems, including transverse shear force calculation, slenderness ratio, spacing, thickness, effective depth, overlap for welded connections, and notes battening offers less shear resistance than lacing.
information on types of beams, different methods to calculate beam stress, design for shear, analysis for SRB flexure, design for flexure, Design procedure for doubly reinforced beam,
Here we discussed about the balanced section,Under reinforced and Over reinforced sections and what are the failure and their moment of resistance.. and also comparison between among three sections
information on types of beams, different methods to calculate beam stress, design for shear, analysis for SRB flexure, design for flexure, Design procedure for doubly reinforced beam,
Here we discussed about the balanced section,Under reinforced and Over reinforced sections and what are the failure and their moment of resistance.. and also comparison between among three sections
Design of steel structure as per is 800(2007)ahsanrabbani
It does not offer resistance against rotation and also termed as a hinged or pinned connections.
It transfers only axial or shear forces and it is not designed for moment
It is generally connected by single bolt/rivet and therefore full rotation is allowed
Design of steel structure as per is 800(2007)ahsanrabbani
It does not offer resistance against rotation and also termed as a hinged or pinned connections.
It transfers only axial or shear forces and it is not designed for moment
It is generally connected by single bolt/rivet and therefore full rotation is allowed
Comparative Study on Anchorage in Reinforced Concrete Using Codes of Practice...IJERA Editor
This paper (Part II) reports a comparative study for BS8110 and EC2 of practice and those expressions by Batayneh and Neilsen on tests from literature. These have been treated under straight bar anchorages with transverse pressure. The aim of this study is to evaluate the reliability of the existing equations for bond strength of straight bars by applying to the available tests in the literature .The most important parameters were examined in these tests are concrete strength, anchorage length, concrete covers, bar diameter and transverse pressure. 264 tests from the literature have been chosen, which are all for straight bars with transverse pressure. The specimens are pull-out specimens with small concrete covers, beams ends and slabs. For both comparative studies in Part I and Part II, the conclusions and recommendations are presented here together.
This presentation is on design of welded and riveted connections in steel structures. in this presentation we learn briefly about these connections and design terminology about these connections.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
1. GANDHINAGAR INSTITUTE OF
TECHNOLOGY
BE SEM :-6th
DEPARTMENT OF CIVIL ENGINERING
Active Learning Assignment of
ELEMENTARY STRUCTURAL DESING
(STEEL)
Topic : LASSING AND BATTERING SYSTEM
Prepared By:
PRAJAPATI HIMANSU 140120106085
Guided By
Prof. Mohammed Challawala
2. Introduction
Typical joining of the components is done by two ways
1. Lacing
2. Battening
Lacing bars or battern plates are not design as load carrying
members.
They carry transverse shear force which occurs when the
column defects.
4. There are two types of lacing system.
1. Single lacing system
2. Double lacing system
The lacing system should not be varied
throughout the length of the strut as far
as practicable.
5. The single-laced systems on opposite sides of the main
components should preferably be in the same direction so that
one system is the shadow of the other.
Cross (except tie plates) should not be provided along the
length of the column with lacing system, unless all forces
resulting from deformation of column members are calculated
and provided for in the lacing and its fastening.
7. (1) Angle of inclination(θ): (cl. 7.6.4)
For single or double lacing system,
θ = 40 ͦ to 70 ͦ To the axis of the built up member
normally,=45 is taken
(2) Slendernes ratio(kL/r) : (cl. 7.6.5.1)
KL/r for each component of column, should not be greater than
50. ( or)
kL/r not greater than 0.7 *most favourable slenderness ratio of
the member as a whole
8. The slenderness ratio of lacing shall not exceed 145
(cl.7.6.6.3)
(3) Effective length of lacing (le) :
For bolted connection :
For single lacing, le = L
For double lacing, le = 0.7 l
Where, L = distance between the inner end fastner
For welded connection :
Le = 0.7 x distance between the inner ends of welds
9. (4) Width of lacing bars(b) : ( cl, 7.6.2)
minimum width of lacing bar, b = 3d
Wh, D = nominal diameter of bolt
(5) Thickness of lacing (t) : (cl. 7.6.3)
For single lacing, t > Le/40
For double lacing, t > Le/60
10. (6) Transverse shear (Vt) : (cl. 7.6.6.1)
Vt= 2.5% of the axial force in the column.
This force shall be divided equally among
the lacing systems in parallel Planes.
For single lacing
F=Vt / 2sin ϴ
For double lacing
F=Vt/4 sin ϴ
wh, F= axial force in each lacing bar
11. (7) Check for compressive strength
For lacing using Le/r min & fy = 250 Mpa
Find fcd from IS: 800, table -9 (c) pg. 42
For rectangular section buckling class is “c”.
So, Compressive load carrying capacity of lacing
Pd = (b x t) x fcd
If (b x t ) x fcd > F (axial force n lacing) …. OK
b*t = area of lacing
i.e. pd > F …. OK
12. (8) Check for Tensile Strength
Tensile strength of lacing flat is,
Or
Whichever is less.
If …O.K. IS : 800 cl. 6.3.1, pg 32
13. (9) End connections :
The bolted connection for lacing may be two types as given case.
For case (a)
Resultant force on bolt = R = F
So, no of bolts required
14. For case (b)
Resultant force on bolt
So No. of bolts required
Strength in single shear
16 dia. Bolts = 29 kN
20 dia. Bolts = 45.3 kN
15. Strength of bolt in bearing (cl. 10.3.4)
(10) Overlap
In case of welded connection, the amount of overlap measured
along either edge of lacing bar shall not be less than , four times
the thickness of the lacing bar (or)
The thickness of the element of main member, whichever is
less.
17. Compression member can also be built up intermediate
horizontal connecting plates or angle connecting two or four
elements of column .these horizontal connecting plates are
called battens.
The number of battens shall be such that the member is divided
into not less than three bays within its actual length
19. (1) The number of battens shall be
such that the member is divided
into not less than three bays.
(2) Battens shall be designed to resist
simultaneous
20. Longitudinal shear
Vb = Vt C / Ns
Moment
M=Vt C / 2N
Where,
Vt = transverse shear force
C = distance between centre to centre of battens longitudinally .
N = number of parallel planes of battens (2 usually)
S = Minimum transverse distance between the centroid of the
bolt/ rivet group / welding.
21. (3) Slenderness Ratio : (cl. 7.7.1.4)
The effective slenderness ratio of battened column
shall be taken as 1.1 times the ,the maximum actual
slenderness ratio of the column, to account for shear deformation
effects.
(4) Spacing of battens (C) : (cl. 7.7.3)
For any component of column,
(1)
(2) of built up column (which ever is smaller)
22. (5) Thickness of battens (t) : (cl. 7.7.2.3)
wh, = distance b/w the inner most
connecting lines of bolts,
perpendicular to the main member
(6) Effective Depth of battens (de) : (cl 7.7.2.3)
de > 3/4 * a …for intermediate battens
de > a,……. ...For end batten
de > 2b , …… For any battens
Wh, de = distance between outermost bolts longitudinally
a = distance between centroids of the main member
b = width of one member
23. Overall depth of battens
D = de + (2 * end distance)
(7) Transverse shear (Vt) : (cl. 7.7.2.1)
Vt = 2.5 % of the factored axial column load
(8) Overlap (cl. 7.7.4.1)
for welded connection, the overlap shall be not less than four
times the thickness of the battens
It should be noted that the battens columns have least
resistance to shear compared to column with lacings