HIGHRISE STRUCTURAL MORPHOLOGY

1. arc5410 Advanced Structure and Construction

2. 3.0 Vertical Structural Systems Pt. 3

3. Types of vertical structural systems

4. The Monadnock Building Pirelli Tower Commerzbank
Bearing wall / pier structures

5. Pirelli Building Gio Ponti with P.L. Nervi Milan, Italy 1960

6. Bartlesville Tower
Core / cantilever structures

7. Johnson Wax Administration Building F. L. Wright Racine, Wisconsin 1939

9. Charter Bank, S. Africa.
Example of tall building with a core tree structure: floors are suspended from cantilevered arms in groups of ten floors.

10. Lake Shore Apartments (steel) Stanhope Building (reinforced concrete)
Rigid frame structures

11. A rigid or semi-rigid frame will deform under lateral loads in two ways: a) cantilever bending and b) shear sway distortion
The combination of these represents the actual behavior of the frame structure.
Stiffening the frame with x-bracing, for example, will cause more cantilever bending and less shear sway

12. Core and frame systems provide adequate stiffness up to 30-40 stories. Generally cores are at the center of the building, both for
practical reasons (daylight) and to resist shear forces more effectively. If not centered, they are usually symmetrically located.
Core and frame structures

13. Examples of tall buildings with cores in various positions. From left to right: Knights of Columbus Building (core at four corners),
Inland Steel (core on one side), PSFS (core on one side), and AT&T (central core)

14. Trussed frame structures

15. First Wisconsin Center Skidmore Owings & Merrill Milwaukee, Wisconsin 1974
An example of a steel frame with a belt truss and outrigger system at the 15th and 41st floors, and a transfer truss at the
3rd level. Note that the outrigger trusses are in the direction of the wind only indicating that wind resistance in the longi-
tudinal direction is provided only by the stiffness of the frame.
Diagrams illustrate the effect of belt truss and outriggers in stiffening a core-frame structure. On
the right, the bending moment decreases in response to increasing stiffness provided by the belt trusses.

17. The research on tall buildings at IIT (Illinois Institute of Technology) under Mies van der Rohe and Fazlur Khan of SOM led to new
concepts on how tall buildings might efficiently resist lateral forces. Myron Goldsmith’s thesis project proposes a super structural
frame, detached from the envelope, and capable of resisting all the lateral forces at the perimeter of the building where it can do so
more effectively.
Myron Goldsmith Superframe 80+ story high rise

18. The Chestnut-Dewitt apartment building (Chicago, 1961-65) and the Brunswick Building (Chicago,
1962-66) were the starting points for Fazlur Khan and SOM’s application of the concept of a framed
tube structure for high rise buildings.
Chestnut-Dewitt Apartment Building Brunswick Building
framed tube tube in tube

19. One Shell Plaza Skidmore Owings & Merrill Houston, Texas 1971
52 story office block “tube in tube” structural type. All lightweight concrete. Matt foundation.

20. Alcoa Building (Truss frame) Skidmore Owings & Merrill San Francisco, CA ca 1965

22. Effect of perimeter trussing to stiffen structure. John Hancock Building, Chicago, USA

23. John Hancock Center SOM / Bruce Graham / Fazlur Khan Chicago 1970

26. Office level floors 26 - 33
Street level

27. Apartment level floors 82 - 92
Sky Lobby floor 44

39. Sears Tower (Sears & Roebuck Co.) Skidmore Owings & Merrill Chicago, IL 1974
109 stories. Bundled tube structural concept. Height to width ratio 6.4.

41. Fazlur Khan’s structural systems classification
Type 1 Shear Frames: semi-rigid and rigid
Type 2 Interacting Systems: frame with shear truss, frame with shear belt & outrigger trusses
Type 3 Partial Tubular Systems: end channel frame with interior shear trusses
Type 4 Tubular Systems: exterior framed tube, bundled frame tube, exterior diagonalized tube

48. “There is more fun than anything else in doing a more elegant solution for an ordinary 75-
story building. We have a long way to go to make the skyscraper what it really can be, and it
doesn’t have to be super-tall to do this. There are ways to open up space, to make it more
economical and to face the problems of fire and transportation and pedestrian joy at the
bottom. These are much more interesting problems.”
William LeMessurier
Engineering News Record November 3, 1983

50. Citicorp Center Hugh Stubbins / Wm. Lemessurier NYC 1977

54. Bank of the Southwest Helmut Jahn and Wm LeMessurier Houston, Texas 1982