This document analyzes the heat transfer performance of a double pipe heat exchanger with circular and square inner sections using computational fluid dynamics (CFD). CFD simulations were conducted using ANSYS Fluent to analyze temperature contours and heat transfer rates. The results showed that the square inner section heat exchanger absorbed more heat from the hot fluid and had a higher heat flow rate than the circular section design, with the cold fluid outlet temperature being higher for the square section. In conclusion, the square inner section design exhibited better heat transfer performance compared to the conventional circular section design for this type of heat exchanger.
This presentation is to show how to design heat exchanger from process simulation data to complete mechanical design by using two software HTRI and COMPRESS in seamless streamline Auto duping data.
Heat exchangers are used widely in industrial application such as chemical,
food processing, power production, refrigeration and air-conditioning
industries. Helical coiled heat exchangers are used in order to obtain a large
heat transfer per unit volume and to enhance the heat transfer rate on the inside
surface. In the present study, CFD simulations are carried out for a counter
flow tube in tube helical heat exchanger where hot water flows through the
inner tube and cold water flows through the outer tube. From the simulation
results heat transfer coefficient, pressure drop and nusselt number are
calculated. The heat transfer characteristics of the same are compared with that
of a counter flow tube in tube straight tube heat exchanger of same length
under same temperature and flow conditions. CFD simulation results showed
that the helical tube in tube heat exchanger is more effective than the straight
tube in tube heat exchanger.
Numerical Analysis of Heat Transfer Enhancement in Pipe-inPipe Helical Coiled...iosrjce
These paper focuses on the effect of the inside tubes at constant value of mass flow rate and variation
of annulus mass flow rate on effect of Dean Number and overall heat transfer coefficient with constant wall
temperature, CFD analysis of a helically coiled heat exchanger. Also deals with the effect of Dean Number with
respect to Reynolds Number and Nusselt Number and Overall Heat Transfer coefficient on change of coil
configuration of helically coiled tube. The particular difference in this study in comparison with the other
similar studies was the boundary conditions for the helical coils. The results indicate that with the decrease the
inner coil diameter, the overall heat transfer coefficient is increased
Analysis of Coiled-Tube Heat Exchangers to Improve Heat Transfer Rate With Sp...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
Helically Coiled Tube with Different Geometry and Curvature Ratio on Convecti...AM Publications
A helically coil-tube heat exchanger is generally applied in industry applications due to its compact structure, larger heat transfer area and higher heat transfer capability. Several studies from literature have also indicated that heat transfer rate in helically coiled tube are superior to straight tube due to complex flow pattern exist inside helical pipe. The concept behind compact heat exchanger is to decrease size and increase heat load which is the typical feature of modern helical tube heat exchanger. While the heat transfer characteristics of helical coil heat exchangers are available in the literature, This paper elaborates a brief review on different curvature ratio and geometry of tubes in heat transfer through heat exchangers.
Esign and thermal evaluation of shell and helical coil heat exchangereSAT Journals
Abstract
Heat exchangers are the important engineering equipments used for transferring heat from one fluid to another. Heat exchangers are widely used in various kinds of application such as power plants, nuclear reactors, refrigeration and air-conditioning systems, heat recovery systems, petrochemical, mechanical, biomedical industries. Helical coil heat exchangers are gaining wide importance now-a-days because it can give high heat transfer coefficient in small footprint of surface area. This paper focuses on the designing of shell and helical coil heat exchanger and its thermal evaluation with counter flow configuration. The thermal analysis is carried out considering the various parameters such as flow rate of cold water, flow rate of hot water, temperature, effectiveness and overall heat transfer coefficient.
Keywords— Helical coil heat exchanger, Counter flow, Flow rate, effectiveness, heat transfer coefficient etc.
Analysis of A Double Spiral Counter Flow Calorimeter in Impinging Flame Jet U...IJERA Editor
Enhancement of heat transfer rates in heat exchanger and calorimeter has been reported by many researchers. However, work regarding heat transfer characteristics analysis of double spiral counter flow calorimeter is not published and this forms the objective of this work. DSCFC is a unique design where it consists of single fluid as working fluid for heat exchange. Here heat transfer takes place between solid and fluid, and hence can be called as conjugate heat transfer problem. Heat transfer characteristics DSCFC is observed at various Reynolds number and base temperature. DSCFC is analyzed considering conjugate heat transfer and temperature dependent properties of heat transport media. Computations are performed using commercially available CFD package ANSYS-CFX. It is observed that with increase in Reynolds number of the fluid, heat transfer reduces whereas increase in base temperature increases heat transfer. The Computational results are compared with the experimental.
Water cooled minichannel heat sinks for microprocessor cooling: Effect of fin...Danial Sohail
Heat sink with different fin spacing mounted on a microprocessor were tested for their heat removing capabilities by varying coolant flow rates over them
This presentation is to show how to design heat exchanger from process simulation data to complete mechanical design by using two software HTRI and COMPRESS in seamless streamline Auto duping data.
Heat exchangers are used widely in industrial application such as chemical,
food processing, power production, refrigeration and air-conditioning
industries. Helical coiled heat exchangers are used in order to obtain a large
heat transfer per unit volume and to enhance the heat transfer rate on the inside
surface. In the present study, CFD simulations are carried out for a counter
flow tube in tube helical heat exchanger where hot water flows through the
inner tube and cold water flows through the outer tube. From the simulation
results heat transfer coefficient, pressure drop and nusselt number are
calculated. The heat transfer characteristics of the same are compared with that
of a counter flow tube in tube straight tube heat exchanger of same length
under same temperature and flow conditions. CFD simulation results showed
that the helical tube in tube heat exchanger is more effective than the straight
tube in tube heat exchanger.
Numerical Analysis of Heat Transfer Enhancement in Pipe-inPipe Helical Coiled...iosrjce
These paper focuses on the effect of the inside tubes at constant value of mass flow rate and variation
of annulus mass flow rate on effect of Dean Number and overall heat transfer coefficient with constant wall
temperature, CFD analysis of a helically coiled heat exchanger. Also deals with the effect of Dean Number with
respect to Reynolds Number and Nusselt Number and Overall Heat Transfer coefficient on change of coil
configuration of helically coiled tube. The particular difference in this study in comparison with the other
similar studies was the boundary conditions for the helical coils. The results indicate that with the decrease the
inner coil diameter, the overall heat transfer coefficient is increased
Analysis of Coiled-Tube Heat Exchangers to Improve Heat Transfer Rate With Sp...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
Helically Coiled Tube with Different Geometry and Curvature Ratio on Convecti...AM Publications
A helically coil-tube heat exchanger is generally applied in industry applications due to its compact structure, larger heat transfer area and higher heat transfer capability. Several studies from literature have also indicated that heat transfer rate in helically coiled tube are superior to straight tube due to complex flow pattern exist inside helical pipe. The concept behind compact heat exchanger is to decrease size and increase heat load which is the typical feature of modern helical tube heat exchanger. While the heat transfer characteristics of helical coil heat exchangers are available in the literature, This paper elaborates a brief review on different curvature ratio and geometry of tubes in heat transfer through heat exchangers.
Esign and thermal evaluation of shell and helical coil heat exchangereSAT Journals
Abstract
Heat exchangers are the important engineering equipments used for transferring heat from one fluid to another. Heat exchangers are widely used in various kinds of application such as power plants, nuclear reactors, refrigeration and air-conditioning systems, heat recovery systems, petrochemical, mechanical, biomedical industries. Helical coil heat exchangers are gaining wide importance now-a-days because it can give high heat transfer coefficient in small footprint of surface area. This paper focuses on the designing of shell and helical coil heat exchanger and its thermal evaluation with counter flow configuration. The thermal analysis is carried out considering the various parameters such as flow rate of cold water, flow rate of hot water, temperature, effectiveness and overall heat transfer coefficient.
Keywords— Helical coil heat exchanger, Counter flow, Flow rate, effectiveness, heat transfer coefficient etc.
Analysis of A Double Spiral Counter Flow Calorimeter in Impinging Flame Jet U...IJERA Editor
Enhancement of heat transfer rates in heat exchanger and calorimeter has been reported by many researchers. However, work regarding heat transfer characteristics analysis of double spiral counter flow calorimeter is not published and this forms the objective of this work. DSCFC is a unique design where it consists of single fluid as working fluid for heat exchange. Here heat transfer takes place between solid and fluid, and hence can be called as conjugate heat transfer problem. Heat transfer characteristics DSCFC is observed at various Reynolds number and base temperature. DSCFC is analyzed considering conjugate heat transfer and temperature dependent properties of heat transport media. Computations are performed using commercially available CFD package ANSYS-CFX. It is observed that with increase in Reynolds number of the fluid, heat transfer reduces whereas increase in base temperature increases heat transfer. The Computational results are compared with the experimental.
Water cooled minichannel heat sinks for microprocessor cooling: Effect of fin...Danial Sohail
Heat sink with different fin spacing mounted on a microprocessor were tested for their heat removing capabilities by varying coolant flow rates over them
Cfd and conjugate heat transfer analysis of heat sinks with different fin geo...eSAT Journals
Abstract Heat sinks are commonly used for cooling of electronic devices. Heat sinks, an array of heat fins, remove the heat from the surfaces of the chips by enhancing the heat Transfer rate through heat conduction process. Heat can also be removed from the chip surfaces through forced convection heat transfer. In this project work, CFD and conjugate heat transfer analysis is carried out for various fin geometries with Zigzag, Fluted, Slanted mirror, Custom pin fin and staggered array configurations for low thermal resistance and minimum pressure drop. Numerical simulations are carried out for each of the above mentioned fin geometries with common base plate thickness of 2 mm, fin height of 28 mm and fin thickness of 1 mm for three different heat loads namely 50 W, 75 W and 100 W with air flow of 3.933 m/s (15 ft3/min or 15 CFM) and air inlet temperature of 25oC. The results are compared for thermal performance of a heat sink for each of above geometries and it is observe that the fin with Slanted Mirror geometry gives the best performance among all the other geometries for minimum Pressure drop. The average heat transfer coefficients for fins with slanted mirror geometry, zig zag configuration, fluted type, custom pin fin and staggered array are found to be 215 W/m2K, 164 W/m2K, 164 W/m2K, 157 W/m2K and 145 W/m2K respectively Keywords: Fin geometries of Heat sinks, Computational Fluid Dynamics, Conjugate heat transfer.
Review on Comparative Study between Helical Coil and Straight Tube Heat Excha...IOSR Journals
The purpose of this study is to determine the relative advantage of using a helically coiled heat
exchanger against a straight tube heat exchanger. It is found that the heat transfer in helical circular tubes is
higher as compared to Straight tube due to their shape. Helical coils offer advantageous over straight tubes due
to their compactness and increased heat transfer coefficient. The increased heat transfer coefficients are a
consequence of the curvature of the coil, which induces centrifugal forces to act on the moving fluid, resulting in
the development of secondary flow. The curvature of the coil governs the centrifugal force while the pitch (or
helix angle) influences the torsion to which the fluid is subjected to. The centrifugal force results in the
development of secondary flow. Due to the curvature effect, the fluid streams in the outer side of the pipe moves
faster than the fluid streams in the inner side of the pipe. The difference in velocity sets-in secondary flows,
whose pattern changes with the Dean number of the flow.
In current work the fluid to fluid heat exchange is taken into consideration, Most of the investigations on heat transfer coefficients are for constant wall temperature or constant heat flux. The effectiveness, overall
heat transfer coefficient, effect of coldwater flow rate on effectiveness of heat exchanger when hot water mass
flow rate is kept constant and effect of hot water flow rate on effectiveness when cold water flow rate kept
constant studied and compared for parallel flow, counter flow arrangement of Helical coil and Straight tube
heat exchangers. The inner heat transfer coefficient calculated from Wilson plot method. Then Nusselt no and
correlation obtained on the basis of inner heat transfer coefficient. All readings were taken at steady state
condition of heat exchanger.
The result shows that the heat transfer coefficient is affected by the geometry of the heat exchanger.
Helical coil heat exchanger are superior in all aspect studied here.
Evaluating mathematical heat transfer effectiveness equations using cfd techn...aeijjournal
Mathematical heat transfer equations for finned double pipe heat exchangers based on experimental work carried out in the 1970s can be programmed in a spreadsheet for repetitive use. Thus avoiding CFD analysis which can be time consuming and costly. However, it is important that such mathematical equations be evaluated for their accuracy. This paper uses CFD methods in evaluating the accuracy of mathematical equations. Several models were created with varying; geometry, flue gas entry temperature,
and flow rates. The analysis should provide designers and manufacturers a judgment on the expected level
of accuracy when using mathematical modelling methodology. This paper simultaneously identifies best
practices in carrying out such CFD analysis
Design and experimental analysis of pipe in pipe heat exchangerIJMER
Pipe in pipe heat exchanger are used in industrial process to recover heat between two
process fluids. The project carried out design of pipe in pipe heat exchanger having tube with fin and
without fin. The fins were taken in the form of semi-circular type arranged in altenating way with
spacing of 50mm.The fins were only provided on the inner tube for creating turbulence of cold water.
The number of fin were 18 and its height and thickness 10 and 1.6mm respectively. Experiment were
performed for heat exchanger with fins and without fins. The experiment were performed for different
flow rates of hot and cold fluid Different parameters like Overall heat transfer,Nusselt
number,Convective heat transfer coefficient,Pressure drop,friction factor were obtained and compared
for simple inner tube and finned tube.
Study of Flow and Heat Transfer Analysis in Shell and Tube Heat Exchanger usi...SuginElankaviR
Heat exchangers are used to transfer heat from fluid at high temperature to fluid at lower temperature. Heat exchangers are used in industrial purposes in chemical industries, nuclear power plants, refineries, food processing, etc. Sizing of heat exchangers plays very significant role for cost optimization. Also, efficiency and effectiveness of heat exchangers is an important parameter while selection of industrial heat exchangers. Methods for improvement on heat transfer have been worked upon for many years in order to obtain high efficiency with optimum cost. In this research work, design of shell & tube heat exchanger with single segmented baffles and analyze the flow and temperature field inside the shell using Autodesk Simulation CFD 2015. When comparing the CFD analysis with experimental results, it was well correlation with negligible percentage of error. Thus, the series of baffles results in a significant increase in heat transfer coefficient per unit pressure drop in the heat exchanger.
CFD Analysis of Plate Fin Tube Heat Exchanger for Various Fin InclinationsIJERA Editor
ANSYS Fluent software is used for three dimensional CFD simulations to investigate heat transfer and fluid flow characteristics of six different fin angles with plain fin tube heat exchangers. The numerical simulation of the fin tube heat exchanger was performed by using a three dimensional numerical computation technique. Geometry of model is created and meshed by using ANSYS Workbench software. To solve the equation for the fluid flow and heat transfer analysis ANSYS FLUENT was used in the fin-tube heat exchanger. The fluid flow and heat transfer are simulated and result compared for both laminar and turbulent flow models k-epsilon and SST k-omega, with steady state solvers to calculate heat transfer, flow velocity and temperature fields of variable inclined fin angles (Ɵ = 00,100 , 200, 300, 400,500). Model is validate by comparing the simulated value of velocity, temperature and colburn factor with experimental and numerical results investigated by WANG [1] and GHORI KIRAR [10]. Reasonable agreement is found between the simulations and other results, and the ANSYS Fluent software is sufficient for simulating the flow fields in tube fin heat exchanger.
Experimentation on heat pipe and cfd analysis for performance enhancementeSAT Journals
Abstract
Heat Pipe is a heat transfer device used in many applications and it is very similar in some respects to the thermosyphon. Since there were several limitations of thermosyphon, heat pipe was developed. The idea of the heat pipe was first suggested in 1942, since then over a several decades the serious development of a heat pipe took place. Heat pipe mainly consists of three regions viz. evaporator, adiabatic and condenser section. The heat pipe differs from the thermosyphon by virtue of its ability to transport heat against gravity by an evaporation-condensation cycle. This research work includes experimentation on available heat pipe, development of CFD model and its validation with experimental results using CFD Tool. The results obtained by CFD are in good agreement with an experimental results. Since the heat pipe is used for transferring the heat, this research work focuses on increasing the heat transfer by modified model, modifications in terms of increased surface area, is proposed. From CFD analysis it was found that the proposed modified heat pipe shows enhancement in performance in terms of heat transfer rate by 19% when it is simulated for without heat sink case and 45% while with heat sink case, compared to conventional heat pipe. The mixture multiphase model from CFD too is used for simulation of heat pipe.
Cfd and conjugate heat transfer analysis of heat sinks with different fin geo...eSAT Journals
Abstract Heat sinks are commonly used for cooling of electronic devices. Heat sinks, an array of heat fins, remove the heat from the surfaces of the chips by enhancing the heat Transfer rate through heat conduction process. Heat can also be removed from the chip surfaces through forced convection heat transfer. In this project work, CFD and conjugate heat transfer analysis is carried out for various fin geometries with Zigzag, Fluted, Slanted mirror, Custom pin fin and staggered array configurations for low thermal resistance and minimum pressure drop. Numerical simulations are carried out for each of the above mentioned fin geometries with common base plate thickness of 2 mm, fin height of 28 mm and fin thickness of 1 mm for three different heat loads namely 50 W, 75 W and 100 W with air flow of 3.933 m/s (15 ft3/min or 15 CFM) and air inlet temperature of 25oC. The results are compared for thermal performance of a heat sink for each of above geometries and it is observe that the fin with Slanted Mirror geometry gives the best performance among all the other geometries for minimum Pressure drop. The average heat transfer coefficients for fins with slanted mirror geometry, zig zag configuration, fluted type, custom pin fin and staggered array are found to be 215 W/m2K, 164 W/m2K, 164 W/m2K, 157 W/m2K and 145 W/m2K respectively Keywords: Fin geometries of Heat sinks, Computational Fluid Dynamics, Conjugate heat transfer.
Review on Comparative Study between Helical Coil and Straight Tube Heat Excha...IOSR Journals
The purpose of this study is to determine the relative advantage of using a helically coiled heat
exchanger against a straight tube heat exchanger. It is found that the heat transfer in helical circular tubes is
higher as compared to Straight tube due to their shape. Helical coils offer advantageous over straight tubes due
to their compactness and increased heat transfer coefficient. The increased heat transfer coefficients are a
consequence of the curvature of the coil, which induces centrifugal forces to act on the moving fluid, resulting in
the development of secondary flow. The curvature of the coil governs the centrifugal force while the pitch (or
helix angle) influences the torsion to which the fluid is subjected to. The centrifugal force results in the
development of secondary flow. Due to the curvature effect, the fluid streams in the outer side of the pipe moves
faster than the fluid streams in the inner side of the pipe. The difference in velocity sets-in secondary flows,
whose pattern changes with the Dean number of the flow.
In current work the fluid to fluid heat exchange is taken into consideration, Most of the investigations on heat transfer coefficients are for constant wall temperature or constant heat flux. The effectiveness, overall
heat transfer coefficient, effect of coldwater flow rate on effectiveness of heat exchanger when hot water mass
flow rate is kept constant and effect of hot water flow rate on effectiveness when cold water flow rate kept
constant studied and compared for parallel flow, counter flow arrangement of Helical coil and Straight tube
heat exchangers. The inner heat transfer coefficient calculated from Wilson plot method. Then Nusselt no and
correlation obtained on the basis of inner heat transfer coefficient. All readings were taken at steady state
condition of heat exchanger.
The result shows that the heat transfer coefficient is affected by the geometry of the heat exchanger.
Helical coil heat exchanger are superior in all aspect studied here.
Evaluating mathematical heat transfer effectiveness equations using cfd techn...aeijjournal
Mathematical heat transfer equations for finned double pipe heat exchangers based on experimental work carried out in the 1970s can be programmed in a spreadsheet for repetitive use. Thus avoiding CFD analysis which can be time consuming and costly. However, it is important that such mathematical equations be evaluated for their accuracy. This paper uses CFD methods in evaluating the accuracy of mathematical equations. Several models were created with varying; geometry, flue gas entry temperature,
and flow rates. The analysis should provide designers and manufacturers a judgment on the expected level
of accuracy when using mathematical modelling methodology. This paper simultaneously identifies best
practices in carrying out such CFD analysis
Design and experimental analysis of pipe in pipe heat exchangerIJMER
Pipe in pipe heat exchanger are used in industrial process to recover heat between two
process fluids. The project carried out design of pipe in pipe heat exchanger having tube with fin and
without fin. The fins were taken in the form of semi-circular type arranged in altenating way with
spacing of 50mm.The fins were only provided on the inner tube for creating turbulence of cold water.
The number of fin were 18 and its height and thickness 10 and 1.6mm respectively. Experiment were
performed for heat exchanger with fins and without fins. The experiment were performed for different
flow rates of hot and cold fluid Different parameters like Overall heat transfer,Nusselt
number,Convective heat transfer coefficient,Pressure drop,friction factor were obtained and compared
for simple inner tube and finned tube.
Study of Flow and Heat Transfer Analysis in Shell and Tube Heat Exchanger usi...SuginElankaviR
Heat exchangers are used to transfer heat from fluid at high temperature to fluid at lower temperature. Heat exchangers are used in industrial purposes in chemical industries, nuclear power plants, refineries, food processing, etc. Sizing of heat exchangers plays very significant role for cost optimization. Also, efficiency and effectiveness of heat exchangers is an important parameter while selection of industrial heat exchangers. Methods for improvement on heat transfer have been worked upon for many years in order to obtain high efficiency with optimum cost. In this research work, design of shell & tube heat exchanger with single segmented baffles and analyze the flow and temperature field inside the shell using Autodesk Simulation CFD 2015. When comparing the CFD analysis with experimental results, it was well correlation with negligible percentage of error. Thus, the series of baffles results in a significant increase in heat transfer coefficient per unit pressure drop in the heat exchanger.
CFD Analysis of Plate Fin Tube Heat Exchanger for Various Fin InclinationsIJERA Editor
ANSYS Fluent software is used for three dimensional CFD simulations to investigate heat transfer and fluid flow characteristics of six different fin angles with plain fin tube heat exchangers. The numerical simulation of the fin tube heat exchanger was performed by using a three dimensional numerical computation technique. Geometry of model is created and meshed by using ANSYS Workbench software. To solve the equation for the fluid flow and heat transfer analysis ANSYS FLUENT was used in the fin-tube heat exchanger. The fluid flow and heat transfer are simulated and result compared for both laminar and turbulent flow models k-epsilon and SST k-omega, with steady state solvers to calculate heat transfer, flow velocity and temperature fields of variable inclined fin angles (Ɵ = 00,100 , 200, 300, 400,500). Model is validate by comparing the simulated value of velocity, temperature and colburn factor with experimental and numerical results investigated by WANG [1] and GHORI KIRAR [10]. Reasonable agreement is found between the simulations and other results, and the ANSYS Fluent software is sufficient for simulating the flow fields in tube fin heat exchanger.
Experimentation on heat pipe and cfd analysis for performance enhancementeSAT Journals
Abstract
Heat Pipe is a heat transfer device used in many applications and it is very similar in some respects to the thermosyphon. Since there were several limitations of thermosyphon, heat pipe was developed. The idea of the heat pipe was first suggested in 1942, since then over a several decades the serious development of a heat pipe took place. Heat pipe mainly consists of three regions viz. evaporator, adiabatic and condenser section. The heat pipe differs from the thermosyphon by virtue of its ability to transport heat against gravity by an evaporation-condensation cycle. This research work includes experimentation on available heat pipe, development of CFD model and its validation with experimental results using CFD Tool. The results obtained by CFD are in good agreement with an experimental results. Since the heat pipe is used for transferring the heat, this research work focuses on increasing the heat transfer by modified model, modifications in terms of increased surface area, is proposed. From CFD analysis it was found that the proposed modified heat pipe shows enhancement in performance in terms of heat transfer rate by 19% when it is simulated for without heat sink case and 45% while with heat sink case, compared to conventional heat pipe. The mixture multiphase model from CFD too is used for simulation of heat pipe.
Experimentation on heat pipe and cfd analysis for performance enhancementeSAT Journals
Abstract
Heat Pipe is a heat transfer device used in many applications and it is very similar in some respects to the thermosyphon. Since there were several limitations of thermosyphon, heat pipe was developed. The idea of the heat pipe was first suggested in 1942, since then over a several decades the serious development of a heat pipe took place. Heat pipe mainly consists of three regions viz. evaporator, adiabatic and condenser section. The heat pipe differs from the thermosyphon by virtue of its ability to transport heat against gravity by an evaporation-condensation cycle. This research work includes experimentation on available heat pipe, development of CFD model and its validation with experimental results using CFD Tool. The results obtained by CFD are in good agreement with an experimental results. Since the heat pipe is used for transferring the heat, this research work focuses on increasing the heat transfer by modified model, modifications in terms of increased surface area, is proposed. From CFD analysis it was found that the proposed modified heat pipe shows enhancement in performance in terms of heat transfer rate by 19% when it is simulated for without heat sink case and 45% while with heat sink case, compared to conventional heat pipe. The mixture multiphase model from CFD too is used for simulation of heat pipe.
Modeling and Fluid Flow Analysis of Wavy Fin Based Automotive RadiatorIJERA Editor
In continuous technological development, an automotive industry has increased the demand for high efficiency engines. A high efficiency engines in not only based on its performance but also for better fuel economy and less emission rate. Radiator is one of the important parts of the internal combustion engine cooling system. The manufacturing cost of the radiator is 20 percent of the whole cost of the engine. So improving the performance and reducing cost of radiators are necessary research. For higher cooling capacity of radiator, addition of fins is one of the approaches to increase the cooling rate of the radiator. In addition, heat transfer fluids at air and fluid side such as water and ethylene glycol exhibit very low thermal conductivity. As a result there is a need for new and innovative heat transfer fluids, known as “Nano fluid” for improving heat transfer rate in an automotive radiator. Recently there have been considerable research findings highlighting superior heat transfer performances of nanofluids about 15-25% of heat transfer enhancement can be achieved by using types of nanofluids. With these specific characteristics, the size and weight of an automotive car radiator can be reduced without affecting its heat transfer performance. An automotive radiator (Wavy fin type) model is modeled on modeling software CATIA V5 and performance evaluation is done on pre-processing software ANSYS 14.0. The temperature and velocity distribution of coolant and air are analyzed by using Computational fluid dynamics environment software CFX. Results have shown that the rate of heat transfer is better when nano fluid (Si C + water) is used as coolant, than the conventional coolant.
Analysis of Heat Transfer in Spiral Plate Heat Exchanger Using Experimental a...ijsrd.com
Heat transfer is the key to several processes in industrial application. In a present days maximum efficient heat transfer equipment are in demand due to increasing energy cost. For achieving maximum heat transfer, the engineers are continuously upgrading their knowledge and skills by their past experience. Present work is a skip in the direction of demonstrating the use of the computational technique as a tool to substitute experimental techniques. For this purpose an experimental set up has been designed and developed. Analysis of heat transfer in spiral plate heat exchanger is performed and same Analysis of heat transfer in spiral plate heat exchanger can be done by commercially procurable computational fluid dynamic (CFD) using ANSYS CFX and validated based on this forecasting. Analysis has been carried out in parallel and counter flow with inward and outward direction for achieving maximum possible heat transfer. In this problem of heat transfer involved the condition where Reynolds number again and again varies as the fluid traverses inside the section of flow from inlet to exit, mass flow rate of working fluid is been modified with time. By more and more analysis and experimentation and systematic data degradation leads to the conclusion that the maximum heat transfer rates is obtained in case of the inward parallel flow configuration compared to all other counterparts, which observed to vary with small difference in each section. Furthermore, for the increase heat transfer rate in spiral plate heat exchanger is obtain by cascading system.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers