The document investigates the influence of wire electrical discharge machining (WEDM) parameters on material removal rate when machining tungsten carbide-cobalt (WC-Co) sintered composite. Experiments were conducted using a response surface methodology with five control factors (pulse on-time, pulse off-time, peak current, servo voltage, and wire tension). The results were used to derive a mathematical model to predict material removal rate and optimize the WEDM process for machining WC-Co composite.
This document summarizes an investigation into the effects of machining parameters on the surface finish and material removal rate when machining an aluminum-copper alloy (AL6351) using wire electric discharge machining (WEDM). The study uses Taguchi's design of experiments method to analyze the effects of pulse on-time, pulse off-time, and peak current. Sixteen experiments were conducted and the material removal rate and surface roughness were measured. The results were analyzed using ANOVA to determine the most significant parameters for improving surface finish and removal rate. The goal of the research was to optimize the WEDM process for machining AL6351 alloy.
Optimization of edm process parameters using taguchi method a revieweSAT Journals
Abstract
Electrical discharge machining is assessed on the basis of Material Removal Rate (MRR), Tool Wear Rate (TWR), and Surface Roughness (SR). Process parameters that mostly affected the EDM Process are Pulse on Time, Pulse off Time, Discharge Current, Arc Gap and Duty Cycle. This paper reviews research for the optimization and improvement of various performance parameters measured in the experimentation on EDM by using Taguchi technique. In the study the main objectives of optimization is to minimize the tool wear rate (TWR) and surface roughness, and to maximize the material removal rate (MRR).Taguchi Method is widely used in the industry to optimize and improve various performance parameters associated with different machining processes. This paper also deals with the review of some of the work reported with the use of Taguchi method in last two decades.
Keywords: - EDM, Wire EDM, MRR, RWR, TWR, SR, Taguchi Technique
Optimization of MRR and SR by employing Taguchis and ANOVA method in EDMIRJET Journal
The document describes research into optimizing material removal rate (MRR) and surface roughness (SR) in electric discharge machining (EDM). Experiments were conducted with four machining parameters (discharge current, source voltage, pulse-on time, and pulse-off time) at different levels using a Taguchi design of experiments approach. Analysis of variance (ANOVA) found that discharge current contributed most to MRR at 33.33%, while pulse-on time contributed most to SR at 30.62%. The study aims to apply Taguchi and ANOVA methods to optimize MRR and SR in EDM.
This document analyzes the effect of different wire electrodes on the material removal rate (MRR) of an MS workpiece using wire electrical discharge machining (WEDM). Experiments were conducted using copper, brass, and zinc-coated brass wire electrodes at various levels of current and pulse duration. The results showed that MRR was highest with copper wire and decreased with brass and zinc-coated brass wires. MRR also decreased with increasing current but increased with longer pulse duration. Statistical analysis through ANOVA confirmed that the wire material and pulse duration significantly affected the MRR while current had a lesser effect.
Optimization of the Process Parameters of Wire Cut EDM - A ReviewIJSRD
The objective of this paper is to study the effect of different process parameter of wire electrical discharge machine (WEDM) process on the performance measures such as material removal rate (MRR), surface roughness, dimensional accuracy and kerf width. It is necessary to evaluate the factors that affect the productivity and efficiency of WEDM process. It will directly contribute to increase cutting speed and dimensional accuracy.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Wire EDM Parameters for Surface Roughness in Straight Gear Manufacturing: An ...Dr. Amarjeet Singh
The gears are an essential component of any system. A gear is a spinning circular machine part with cut teeth, or inserted teeth (called cogs) in the case of a cogwheel or gearwheel, which mesh with another toothed part to convey torque. A gear is sometimes referred as a cog colloquially. Geared devices can adjust a power source's speed, torque, and direction. To eliminate backlash, high precision is required while making gears. Wire cut EDM is a high-precision machining technology that may manufacture high-precision straight gear. The goal of this research is to use the WEDM Process on an EMS 45 to determine the surface roughness of the workpiece and to optimise the influence of current and wire speed on the surface roughness of the straight gear. Wire cut machining parameters employed were 4, 6, and 8 amperes of current and 9, 11, and 13 mm/min of wire speed. Wire has a diameter of 0.25 mm, and the cutting material is brass. It has been demonstrated that as current and wire speed increase, surface roughness decreases, and vice versa. As a result, reduced machine settings can be used to generate a smoother and better workpiece surface.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
call for paper 2012, hard copy of journal, research paper publishing, where to publish research paper,
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
This document summarizes an investigation into the effects of machining parameters on the surface finish and material removal rate when machining an aluminum-copper alloy (AL6351) using wire electric discharge machining (WEDM). The study uses Taguchi's design of experiments method to analyze the effects of pulse on-time, pulse off-time, and peak current. Sixteen experiments were conducted and the material removal rate and surface roughness were measured. The results were analyzed using ANOVA to determine the most significant parameters for improving surface finish and removal rate. The goal of the research was to optimize the WEDM process for machining AL6351 alloy.
Optimization of edm process parameters using taguchi method a revieweSAT Journals
Abstract
Electrical discharge machining is assessed on the basis of Material Removal Rate (MRR), Tool Wear Rate (TWR), and Surface Roughness (SR). Process parameters that mostly affected the EDM Process are Pulse on Time, Pulse off Time, Discharge Current, Arc Gap and Duty Cycle. This paper reviews research for the optimization and improvement of various performance parameters measured in the experimentation on EDM by using Taguchi technique. In the study the main objectives of optimization is to minimize the tool wear rate (TWR) and surface roughness, and to maximize the material removal rate (MRR).Taguchi Method is widely used in the industry to optimize and improve various performance parameters associated with different machining processes. This paper also deals with the review of some of the work reported with the use of Taguchi method in last two decades.
Keywords: - EDM, Wire EDM, MRR, RWR, TWR, SR, Taguchi Technique
Optimization of MRR and SR by employing Taguchis and ANOVA method in EDMIRJET Journal
The document describes research into optimizing material removal rate (MRR) and surface roughness (SR) in electric discharge machining (EDM). Experiments were conducted with four machining parameters (discharge current, source voltage, pulse-on time, and pulse-off time) at different levels using a Taguchi design of experiments approach. Analysis of variance (ANOVA) found that discharge current contributed most to MRR at 33.33%, while pulse-on time contributed most to SR at 30.62%. The study aims to apply Taguchi and ANOVA methods to optimize MRR and SR in EDM.
This document analyzes the effect of different wire electrodes on the material removal rate (MRR) of an MS workpiece using wire electrical discharge machining (WEDM). Experiments were conducted using copper, brass, and zinc-coated brass wire electrodes at various levels of current and pulse duration. The results showed that MRR was highest with copper wire and decreased with brass and zinc-coated brass wires. MRR also decreased with increasing current but increased with longer pulse duration. Statistical analysis through ANOVA confirmed that the wire material and pulse duration significantly affected the MRR while current had a lesser effect.
Optimization of the Process Parameters of Wire Cut EDM - A ReviewIJSRD
The objective of this paper is to study the effect of different process parameter of wire electrical discharge machine (WEDM) process on the performance measures such as material removal rate (MRR), surface roughness, dimensional accuracy and kerf width. It is necessary to evaluate the factors that affect the productivity and efficiency of WEDM process. It will directly contribute to increase cutting speed and dimensional accuracy.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Wire EDM Parameters for Surface Roughness in Straight Gear Manufacturing: An ...Dr. Amarjeet Singh
The gears are an essential component of any system. A gear is a spinning circular machine part with cut teeth, or inserted teeth (called cogs) in the case of a cogwheel or gearwheel, which mesh with another toothed part to convey torque. A gear is sometimes referred as a cog colloquially. Geared devices can adjust a power source's speed, torque, and direction. To eliminate backlash, high precision is required while making gears. Wire cut EDM is a high-precision machining technology that may manufacture high-precision straight gear. The goal of this research is to use the WEDM Process on an EMS 45 to determine the surface roughness of the workpiece and to optimise the influence of current and wire speed on the surface roughness of the straight gear. Wire cut machining parameters employed were 4, 6, and 8 amperes of current and 9, 11, and 13 mm/min of wire speed. Wire has a diameter of 0.25 mm, and the cutting material is brass. It has been demonstrated that as current and wire speed increase, surface roughness decreases, and vice versa. As a result, reduced machine settings can be used to generate a smoother and better workpiece surface.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
call for paper 2012, hard copy of journal, research paper publishing, where to publish research paper,
journal publishing, how to publish research paper, Call For research paper, international journal, publishing a paper, IJERD, journal of science and technology, how to get a research paper published, publishing a paper, publishing of journal, publishing of research paper, reserach and review articles, IJERD Journal, How to publish your research paper, publish research paper, open access engineering journal, Engineering journal, Mathemetics journal, Physics journal, Chemistry journal, Computer Engineering, Computer Science journal, how to submit your paper, peer reviw journal, indexed journal, reserach and review articles, engineering journal, www.ijerd.com, research journals,
yahoo journals, bing journals, International Journal of Engineering Research and Development, google journals, hard copy of journal
Optimization of Surface Roughness for EN 1010 Low Alloy Steel on WEDM Using R...IJAEMSJORNAL
This document describes research into optimizing the surface roughness of EN 1010 low alloy steel using wire electrical discharge machining (WEDM). Experiments were conducted using a central composite design to investigate the effects of four process parameters (pulse on time, pulse off time, peak current, and servo voltage) on surface roughness. Analysis of variance was used to identify significant parameters and develop a mathematical model relating the parameters to surface roughness. The model achieved a good fit to the data and can be used to determine the optimal parameter settings that minimize surface roughness.
Multi-Objective Optimization of EDM process parameters using Taguchi-Grey Rel...IRJET Journal
This document presents a study that uses Taguchi-Grey Relational Analysis to optimize the EDM process parameters for aluminum work material with a copper electrode. The objectives are to maximize the material removal rate and minimize the tool wear rate and surface roughness. Experiments are conducted with four machining parameters (discharge current, pulse on time, flushing pressure, and polarity) each at two levels. Response data is analyzed using Grey Relational Analysis to determine the optimal parameter combination and ranking. The optimal levels found are discharge current of 16A, pulse on time of 1010 μs, flushing pressure of 5kgf/cm2, and normal polarity. Analysis of variance indicates that discharge current has the most significant influence on the output responses
Optimization of WEDM Process Parameters on Titanium Alloy Using Taguchi MethodIJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Modern Engineering Research (IJMER) covers all the fields of engineering and science: Electrical Engineering, Mechanical Engineering, Civil Engineering, Chemical Engineering, Computer Engineering, Agricultural Engineering, Aerospace Engineering, Thermodynamics, Structural Engineering, Control Engineering, Robotics, Mechatronics, Fluid Mechanics, Nanotechnology, Simulators, Web-based Learning, Remote Laboratories, Engineering Design Methods, Education Research, Students' Satisfaction and Motivation, Global Projects, and Assessment…. And many more.
IRJET-Experimental Analysis Optimization of Process Parameters of Wire EDM on...IRJET Journal
This document analyzes the optimization of process parameters for wire electrical discharge machining (WEDM) of stainless steel 316L. It conducts experiments using different controllable factors like discharge current, pulse on/off time, and arc gap. Taguchi design of experiments is used to optimize for maximum material removal rate. Experiments are conducted using a copper tool on 316L stainless steel workpieces. The results are analyzed to determine the optimum parameter levels for achieving higher material removal rate and better surface finish quality during WEDM of 316L stainless steel.
Optimization of machining parameters in edm of cfrp composite using taguchi t...IAEME Publication
1. The document summarizes a study that used Taguchi methods to optimize machining parameters for electrical discharge machining (EDM) of carbon fiber reinforced plastic (CFRP) composite material.
2. The study investigated the effects of gap voltage, discharge current, and pulse-on time on surface roughness. Experiments were conducted using an L9 orthogonal array.
3. Analysis of variance (ANOVA) and signal-to-noise ratios were used to analyze the results. It was found that discharge current had the most significant influence on surface roughness, and confirmation experiments validated the optimum parameters identified.
Development of a Taguchi-based framework for optimizing two quality character...IJERA Editor
This document describes a framework developed using Taguchi methods to optimize two quality characteristics, surface roughness and angular accuracy, in wire electrical discharge machining (W-EDM) operations. An experiment was conducted using an L9 orthogonal array to investigate the effects of four controllable factors (pulse on time, feed rate, voltage, and wire tension), each at three levels, on the two response variables. The optimal settings identified were able to improve both surface roughness and angular accuracy, as confirmed through additional validation experiments. This research established a systematic approach for obtaining a single optimal parameter setting to maximize multiple quality characteristics simultaneously in machining applications.
This document provides a dissertation on investigating the machining characteristics of titanium alloy (Ti-6Al-4V) using the electrical discharge machining (EDM) process. The dissertation includes an introduction to traditional and non-traditional machining processes. It then focuses on EDM, including the history, types, principles, parameters, materials, advantages, and limitations. The methodology section describes the materials, equipment, experimental design using Taguchi methods, and parameters/levels studied. Results and discussions are presented on material removal rate, tool wear rate, surface roughness, and microhardness based on experiments. Finally, conclusions are drawn and scope for future work is discussed.
Modeling and optimization of edm process parameters a reviewIAEME Publication
This document provides a review of research on modeling and optimization of electrical discharge machining (EDM) process parameters. It summarizes 22 research papers that developed mathematical models and applied optimization techniques like response surface methodology, Taguchi method, and genetic algorithms to determine optimal process parameters. The parameters studied include current, pulse on/off time, voltage, and material/electrode properties. The goals of optimization were to improve material removal rate, reduce tool wear and surface roughness. Modeling helped establish relationships between input and output parameters for better process control and performance.
The document discusses a study on the effect of electrical discharge machining (EDM) parameters on high carbon-chromium steel. Central composite design was used to conduct experiments varying pulse on time, duty cycle, current, voltage gap, and pressure. Response variables of material removal rate, electrode wear rate, and surface roughness were analyzed. For material removal rate, the linear model best fit the data. Interaction effects best modeled electrode wear rate, with some parameters having high impact. The interaction model also best fit surface roughness data. Overall, the study used statistical methods to develop models relating EDM parameters to response variables for high carbon-chromium steel EDM.
Optimization of Cutting Rate for EN 1010 Low Alloy Steel on WEDM Using Respon...IJAEMSJORNAL
The document describes an experiment to optimize cutting rate (CR) when machining EN 1010 low alloy steel using wire electric discharge machining (WEDM). Central composite design was used to plan experiments varying pulse on time, pulse off time, peak current, and servo voltage. 21 experiments were conducted and the average CR was measured for each. Response surface methodology was applied to develop a model relating the process parameters to CR. Analysis of variance showed the quadratic model adequately described the relationship with an R2 of 0.970641. An empirical equation was derived to predict optimal CR based on settings of the four process parameters.
Parametric Optimization of Graphite Plate by WEDMIRJET Journal
This document summarizes a study that used the Taguchi method to optimize the wire electrical discharge machining (WEDM) process parameters for machining graphite plates. Experiments were conducted using a WEDM machine to cut graphite plates with a 0.25mm brass wire. The process parameters investigated were current, pulse on time, pulse off time, and wire tension at three levels each based on an L9 orthogonal array design of experiments. Responses measured were material removal rate and surface roughness. Analysis of variance and signal-to-noise ratio graphs identified optimal parameters as 5A current, 5μs pulse on time, 25μs pulse off time, and 10gm wire tension for maximum material removal rate, and
The document discusses using a genetic algorithm approach to optimize process parameters in laser beam welding of Inconel. Experiments were conducted varying pulse duration, pulse frequency, welding speed, and pulse energy. Response surface methodology was used to develop mathematical models relating the weld bead geometry (penetration, width, volume) to the process parameters. The models are then used with a genetic algorithm to optimize the total bead volume while keeping the other geometry parameters within constraints, in order to produce high quality welds efficiently. In summary, the proposed methodology enables determining optimal process settings for different production needs and potentially automating the welding process.
THE EFFECTS OF MACHINING PARAMETERS ON SURFACE ROUGHNESS OF MATERIAL EN-31 IN...ijiert bestjournal
The paper represent the work done for making mathematical models fo r analysis of the effects of machining parameters on the performance characteristics in EDM process of Alloy steel (EN-31). The mathematical models are developed using the response surface methodology (RSM) to explai n the influences of machining parameters on the performance characteristics in the EDM process.
Investigation on Optimization of Machining Parameters in Wire EDM using Taguc...ijsrd.com
In this paper, the parameters used in the cutting of Cemented Tungsten Carbide using wire electrical discharge machining (WEDM) with a Brass electrode was optimized using Taguchi method. Taguchi method is used to formulate the experimental layout and to analyze the effect of each parameter on the machining characteristics. Also it is used to predict the optimal choice for each parameter such as peak current, voltage, and pulse duration and interval time. It was found that these parameters have significant influence on machining characteristics such as Metal Removal Rate (MRR) and Surface Roughness (SR). The result of the work reveals that, the peak current significantly affects the Surface Roughness (SR) and the pulse duration mainly affects the Metal Removal Rate (MRR).
Experiment investigation of edm parameter mrr and twr with multi wall carbonIAEME Publication
This document discusses an experimental investigation of electric discharge machining (EDM) parameters using multi-wall carbon nanotubes. The study analyzed material removal rate and tool wear rate when using EDM on EN-31 steel with an aluminum electrode. Multi-wall carbon nanotubes were mixed with dielectric fluid to determine their effect on output parameters. Experiments followed a full factorial design and regression models were developed to predict parameters. Results found that material removal rate improved by 19% on average while tool wear rate decreased by 8.51% when using multi-wall carbon nanotubes in EDM, as compared to not using nanotubes.
Comparative analysis for higher channel isolation using singleIAEME Publication
This document summarizes the results of two simulations comparing different fiber Bragg grating (FBG) filter configurations for achieving higher channel isolation in dense wavelength-division multiplexing (WDM) systems. The first simulation used a single FBG filter with uniform, Gaussian, or hyperbolic tangent apodization profiles, while the second used two FBG filters connected back-to-back, with the first using uniform apodization and the second using different profiles. For a data rate of 10.52 Gbps and 100 GHz channel spacing, the second simulation achieved lower bit error rates using Gaussian apodization, indicating it provided higher channel isolation than the first simulation or uniform apodization profiles.
This document discusses a proposed software defined network (SDN) based firewall technique. The key aspects of the proposed system are:
1. It separates the control plane functionality (e.g. routing decisions) from the data plane/forwarding plane functionality (e.g. packet forwarding). This is done using an OpenFlow switch as the forwarding element and a central controller to handle control plane functions.
2. The OpenFlow switch uses flow tables populated by the central controller to forward packets. The central controller enforces network policies by programming the flow tables of OpenFlow switches.
3. This architecture allows the OpenFlow switch to be used as a software-defined firewall, with the central controller enforcing firewall rules
Performance and emission characteristics of di ci diesel engine with preIAEME Publication
This document summarizes an experimental study that investigated the performance and emission characteristics of a direct injection compression ignition diesel engine fueled with preheated chicken fat biodiesel. The engine performance, combustion characteristics, and exhaust emissions were tested and compared for petroleum diesel, unheated chicken fat biodiesel, and chicken fat biodiesel preheated to 50°C. Results showed that preheating the chicken fat biodiesel improved engine performance by reducing fuel consumption and brake specific fuel consumption. Preheating also improved combustion and lowered exhaust emissions of carbon monoxide and unburned hydrocarbons compared to unheated chicken fat biodiesel. The study concluded that preheated chicken fat biodiesel can be used
Effect of rotor resistance and compensation in indirect vector control usingIAEME Publication
This document summarizes a research paper that examines the effect of rotor resistance variation in indirect vector control of induction motors. It proposes estimating the rotor resistance using an artificial neural network (ANN) approach to compensate for resistance changes due to temperature rise. Simulation and experimental results show that without compensation, resistance variation leads to performance deterioration. The ANN model estimates resistance from the error between flux estimates from voltage and current models. Estimated resistance is fed back into the controller to improve performance under varying resistance conditions. Results demonstrate compensation of resistance increases the accuracy of torque, flux and current control.
Breakthrough column studies for removal of iron ii from groundwater usingIAEME Publication
This document summarizes a study on removing iron from groundwater using wooden charcoal and sand in column experiments. The study finds that increasing the bed depth and decreasing the linear flow rate through the bed increases the breakthrough time and adsorption capacity for iron. Wooden charcoal shows a higher adsorption capacity for iron compared to sand. Upscaled columns with larger diameters perform better than models of traditional units, yielding higher throughput at breakthrough. The upscaled columns also help remove other contaminants like fluoride, turbidity, sulfate and alkalinity at the iron breakthrough point.
Implications of stereotypical self and public nursing image on performanceIAEME Publication
This document summarizes a study that examined the implications of stereotypical self-image and public image on the performance of nurses and nursing students. The study involved 120 nurses and 120 nursing students who completed questionnaires measuring their perceptions of nursing image and role performance. Additionally, focus groups were conducted with 39 nursing students. The results found that perceptions of nursing image were generally positive, though self-image was rated higher than public image. More nurses felt they lacked expertise in all tasks compared to students. Nurses also reported feeling like they had little to offer and did not contribute enough to the profession. The focus groups identified themes around image and career choice, the influence of media on public image, and approaches to improve nursing image internally and externally
Analysis electrocardiogram signal using ensemble empirical mode decomposition...IAEME Publication
This document discusses techniques for analyzing electrocardiogram (ECG) signals that are noisy and non-stationary. It compares the Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), and Discrete Wavelet Transform (DWT) for denoising ECG signals, finding that EEMD performs best by preserving true waveform features while eliminating noise. It also analyzes normal and abnormal (atrial fibrillation) ECG signals using parametric (periodogram, capon, time-varying autoregressive) and non-parametric (S-transform, smoothed pseudo affine Wigner distributions) time-frequency techniques, determining that the periodogram technique provides the best resolution
Optimization of Surface Roughness for EN 1010 Low Alloy Steel on WEDM Using R...IJAEMSJORNAL
This document describes research into optimizing the surface roughness of EN 1010 low alloy steel using wire electrical discharge machining (WEDM). Experiments were conducted using a central composite design to investigate the effects of four process parameters (pulse on time, pulse off time, peak current, and servo voltage) on surface roughness. Analysis of variance was used to identify significant parameters and develop a mathematical model relating the parameters to surface roughness. The model achieved a good fit to the data and can be used to determine the optimal parameter settings that minimize surface roughness.
Multi-Objective Optimization of EDM process parameters using Taguchi-Grey Rel...IRJET Journal
This document presents a study that uses Taguchi-Grey Relational Analysis to optimize the EDM process parameters for aluminum work material with a copper electrode. The objectives are to maximize the material removal rate and minimize the tool wear rate and surface roughness. Experiments are conducted with four machining parameters (discharge current, pulse on time, flushing pressure, and polarity) each at two levels. Response data is analyzed using Grey Relational Analysis to determine the optimal parameter combination and ranking. The optimal levels found are discharge current of 16A, pulse on time of 1010 μs, flushing pressure of 5kgf/cm2, and normal polarity. Analysis of variance indicates that discharge current has the most significant influence on the output responses
Optimization of WEDM Process Parameters on Titanium Alloy Using Taguchi MethodIJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Modern Engineering Research (IJMER) covers all the fields of engineering and science: Electrical Engineering, Mechanical Engineering, Civil Engineering, Chemical Engineering, Computer Engineering, Agricultural Engineering, Aerospace Engineering, Thermodynamics, Structural Engineering, Control Engineering, Robotics, Mechatronics, Fluid Mechanics, Nanotechnology, Simulators, Web-based Learning, Remote Laboratories, Engineering Design Methods, Education Research, Students' Satisfaction and Motivation, Global Projects, and Assessment…. And many more.
IRJET-Experimental Analysis Optimization of Process Parameters of Wire EDM on...IRJET Journal
This document analyzes the optimization of process parameters for wire electrical discharge machining (WEDM) of stainless steel 316L. It conducts experiments using different controllable factors like discharge current, pulse on/off time, and arc gap. Taguchi design of experiments is used to optimize for maximum material removal rate. Experiments are conducted using a copper tool on 316L stainless steel workpieces. The results are analyzed to determine the optimum parameter levels for achieving higher material removal rate and better surface finish quality during WEDM of 316L stainless steel.
Optimization of machining parameters in edm of cfrp composite using taguchi t...IAEME Publication
1. The document summarizes a study that used Taguchi methods to optimize machining parameters for electrical discharge machining (EDM) of carbon fiber reinforced plastic (CFRP) composite material.
2. The study investigated the effects of gap voltage, discharge current, and pulse-on time on surface roughness. Experiments were conducted using an L9 orthogonal array.
3. Analysis of variance (ANOVA) and signal-to-noise ratios were used to analyze the results. It was found that discharge current had the most significant influence on surface roughness, and confirmation experiments validated the optimum parameters identified.
Development of a Taguchi-based framework for optimizing two quality character...IJERA Editor
This document describes a framework developed using Taguchi methods to optimize two quality characteristics, surface roughness and angular accuracy, in wire electrical discharge machining (W-EDM) operations. An experiment was conducted using an L9 orthogonal array to investigate the effects of four controllable factors (pulse on time, feed rate, voltage, and wire tension), each at three levels, on the two response variables. The optimal settings identified were able to improve both surface roughness and angular accuracy, as confirmed through additional validation experiments. This research established a systematic approach for obtaining a single optimal parameter setting to maximize multiple quality characteristics simultaneously in machining applications.
This document provides a dissertation on investigating the machining characteristics of titanium alloy (Ti-6Al-4V) using the electrical discharge machining (EDM) process. The dissertation includes an introduction to traditional and non-traditional machining processes. It then focuses on EDM, including the history, types, principles, parameters, materials, advantages, and limitations. The methodology section describes the materials, equipment, experimental design using Taguchi methods, and parameters/levels studied. Results and discussions are presented on material removal rate, tool wear rate, surface roughness, and microhardness based on experiments. Finally, conclusions are drawn and scope for future work is discussed.
Modeling and optimization of edm process parameters a reviewIAEME Publication
This document provides a review of research on modeling and optimization of electrical discharge machining (EDM) process parameters. It summarizes 22 research papers that developed mathematical models and applied optimization techniques like response surface methodology, Taguchi method, and genetic algorithms to determine optimal process parameters. The parameters studied include current, pulse on/off time, voltage, and material/electrode properties. The goals of optimization were to improve material removal rate, reduce tool wear and surface roughness. Modeling helped establish relationships between input and output parameters for better process control and performance.
The document discusses a study on the effect of electrical discharge machining (EDM) parameters on high carbon-chromium steel. Central composite design was used to conduct experiments varying pulse on time, duty cycle, current, voltage gap, and pressure. Response variables of material removal rate, electrode wear rate, and surface roughness were analyzed. For material removal rate, the linear model best fit the data. Interaction effects best modeled electrode wear rate, with some parameters having high impact. The interaction model also best fit surface roughness data. Overall, the study used statistical methods to develop models relating EDM parameters to response variables for high carbon-chromium steel EDM.
Optimization of Cutting Rate for EN 1010 Low Alloy Steel on WEDM Using Respon...IJAEMSJORNAL
The document describes an experiment to optimize cutting rate (CR) when machining EN 1010 low alloy steel using wire electric discharge machining (WEDM). Central composite design was used to plan experiments varying pulse on time, pulse off time, peak current, and servo voltage. 21 experiments were conducted and the average CR was measured for each. Response surface methodology was applied to develop a model relating the process parameters to CR. Analysis of variance showed the quadratic model adequately described the relationship with an R2 of 0.970641. An empirical equation was derived to predict optimal CR based on settings of the four process parameters.
Parametric Optimization of Graphite Plate by WEDMIRJET Journal
This document summarizes a study that used the Taguchi method to optimize the wire electrical discharge machining (WEDM) process parameters for machining graphite plates. Experiments were conducted using a WEDM machine to cut graphite plates with a 0.25mm brass wire. The process parameters investigated were current, pulse on time, pulse off time, and wire tension at three levels each based on an L9 orthogonal array design of experiments. Responses measured were material removal rate and surface roughness. Analysis of variance and signal-to-noise ratio graphs identified optimal parameters as 5A current, 5μs pulse on time, 25μs pulse off time, and 10gm wire tension for maximum material removal rate, and
The document discusses using a genetic algorithm approach to optimize process parameters in laser beam welding of Inconel. Experiments were conducted varying pulse duration, pulse frequency, welding speed, and pulse energy. Response surface methodology was used to develop mathematical models relating the weld bead geometry (penetration, width, volume) to the process parameters. The models are then used with a genetic algorithm to optimize the total bead volume while keeping the other geometry parameters within constraints, in order to produce high quality welds efficiently. In summary, the proposed methodology enables determining optimal process settings for different production needs and potentially automating the welding process.
THE EFFECTS OF MACHINING PARAMETERS ON SURFACE ROUGHNESS OF MATERIAL EN-31 IN...ijiert bestjournal
The paper represent the work done for making mathematical models fo r analysis of the effects of machining parameters on the performance characteristics in EDM process of Alloy steel (EN-31). The mathematical models are developed using the response surface methodology (RSM) to explai n the influences of machining parameters on the performance characteristics in the EDM process.
Investigation on Optimization of Machining Parameters in Wire EDM using Taguc...ijsrd.com
In this paper, the parameters used in the cutting of Cemented Tungsten Carbide using wire electrical discharge machining (WEDM) with a Brass electrode was optimized using Taguchi method. Taguchi method is used to formulate the experimental layout and to analyze the effect of each parameter on the machining characteristics. Also it is used to predict the optimal choice for each parameter such as peak current, voltage, and pulse duration and interval time. It was found that these parameters have significant influence on machining characteristics such as Metal Removal Rate (MRR) and Surface Roughness (SR). The result of the work reveals that, the peak current significantly affects the Surface Roughness (SR) and the pulse duration mainly affects the Metal Removal Rate (MRR).
Experiment investigation of edm parameter mrr and twr with multi wall carbonIAEME Publication
This document discusses an experimental investigation of electric discharge machining (EDM) parameters using multi-wall carbon nanotubes. The study analyzed material removal rate and tool wear rate when using EDM on EN-31 steel with an aluminum electrode. Multi-wall carbon nanotubes were mixed with dielectric fluid to determine their effect on output parameters. Experiments followed a full factorial design and regression models were developed to predict parameters. Results found that material removal rate improved by 19% on average while tool wear rate decreased by 8.51% when using multi-wall carbon nanotubes in EDM, as compared to not using nanotubes.
Comparative analysis for higher channel isolation using singleIAEME Publication
This document summarizes the results of two simulations comparing different fiber Bragg grating (FBG) filter configurations for achieving higher channel isolation in dense wavelength-division multiplexing (WDM) systems. The first simulation used a single FBG filter with uniform, Gaussian, or hyperbolic tangent apodization profiles, while the second used two FBG filters connected back-to-back, with the first using uniform apodization and the second using different profiles. For a data rate of 10.52 Gbps and 100 GHz channel spacing, the second simulation achieved lower bit error rates using Gaussian apodization, indicating it provided higher channel isolation than the first simulation or uniform apodization profiles.
This document discusses a proposed software defined network (SDN) based firewall technique. The key aspects of the proposed system are:
1. It separates the control plane functionality (e.g. routing decisions) from the data plane/forwarding plane functionality (e.g. packet forwarding). This is done using an OpenFlow switch as the forwarding element and a central controller to handle control plane functions.
2. The OpenFlow switch uses flow tables populated by the central controller to forward packets. The central controller enforces network policies by programming the flow tables of OpenFlow switches.
3. This architecture allows the OpenFlow switch to be used as a software-defined firewall, with the central controller enforcing firewall rules
Performance and emission characteristics of di ci diesel engine with preIAEME Publication
This document summarizes an experimental study that investigated the performance and emission characteristics of a direct injection compression ignition diesel engine fueled with preheated chicken fat biodiesel. The engine performance, combustion characteristics, and exhaust emissions were tested and compared for petroleum diesel, unheated chicken fat biodiesel, and chicken fat biodiesel preheated to 50°C. Results showed that preheating the chicken fat biodiesel improved engine performance by reducing fuel consumption and brake specific fuel consumption. Preheating also improved combustion and lowered exhaust emissions of carbon monoxide and unburned hydrocarbons compared to unheated chicken fat biodiesel. The study concluded that preheated chicken fat biodiesel can be used
Effect of rotor resistance and compensation in indirect vector control usingIAEME Publication
This document summarizes a research paper that examines the effect of rotor resistance variation in indirect vector control of induction motors. It proposes estimating the rotor resistance using an artificial neural network (ANN) approach to compensate for resistance changes due to temperature rise. Simulation and experimental results show that without compensation, resistance variation leads to performance deterioration. The ANN model estimates resistance from the error between flux estimates from voltage and current models. Estimated resistance is fed back into the controller to improve performance under varying resistance conditions. Results demonstrate compensation of resistance increases the accuracy of torque, flux and current control.
Breakthrough column studies for removal of iron ii from groundwater usingIAEME Publication
This document summarizes a study on removing iron from groundwater using wooden charcoal and sand in column experiments. The study finds that increasing the bed depth and decreasing the linear flow rate through the bed increases the breakthrough time and adsorption capacity for iron. Wooden charcoal shows a higher adsorption capacity for iron compared to sand. Upscaled columns with larger diameters perform better than models of traditional units, yielding higher throughput at breakthrough. The upscaled columns also help remove other contaminants like fluoride, turbidity, sulfate and alkalinity at the iron breakthrough point.
Implications of stereotypical self and public nursing image on performanceIAEME Publication
This document summarizes a study that examined the implications of stereotypical self-image and public image on the performance of nurses and nursing students. The study involved 120 nurses and 120 nursing students who completed questionnaires measuring their perceptions of nursing image and role performance. Additionally, focus groups were conducted with 39 nursing students. The results found that perceptions of nursing image were generally positive, though self-image was rated higher than public image. More nurses felt they lacked expertise in all tasks compared to students. Nurses also reported feeling like they had little to offer and did not contribute enough to the profession. The focus groups identified themes around image and career choice, the influence of media on public image, and approaches to improve nursing image internally and externally
Analysis electrocardiogram signal using ensemble empirical mode decomposition...IAEME Publication
This document discusses techniques for analyzing electrocardiogram (ECG) signals that are noisy and non-stationary. It compares the Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), and Discrete Wavelet Transform (DWT) for denoising ECG signals, finding that EEMD performs best by preserving true waveform features while eliminating noise. It also analyzes normal and abnormal (atrial fibrillation) ECG signals using parametric (periodogram, capon, time-varying autoregressive) and non-parametric (S-transform, smoothed pseudo affine Wigner distributions) time-frequency techniques, determining that the periodogram technique provides the best resolution
Development of a web based decision support system for materials selection in...IAEME Publication
This document describes the development of a web-based decision support system for materials selection in construction projects. It proposes a framework that includes a database to store materials information and a decision support component to evaluate materials based on selection criteria. A web interface is developed to allow project participants in different locations to access and manage materials data. The system aims to standardize and automate the materials selection process for construction engineering projects. It discusses developing a conceptual model and database, as well as interfaces like a materials controller to input, view and evaluate options based on criteria like cost, durability and environmental impacts.
Design and implementation of multi channel frame synchronization in fpgaIAEME Publication
This document summarizes a research paper that designed and implemented a multi-channel frame synchronization system in an FPGA. It used low voltage differential signaling receivers to interface satellite data to the FPGA. The FPGA implemented logic for data simulation, frame synchronization, and associated functions like flywheel logic and bit slip correction. Frame synchronization was achieved through correlating received data to a reference pattern, allowing for some bit errors. The design provides reliable synchronization in noisy conditions through an adaptive synchronization strategy and state machine.
Development of pattern knowledge discovery framework usingIAEME Publication
The document describes a proposed pattern knowledge discovery framework using clustering data mining algorithms. It begins with an introduction and literature review on existing approaches. A framework is then proposed with graphical and logical views consisting of data acquisition, pre-processing, processing using clustering algorithms, evaluation/analysis, and pattern knowledge discovery stages. The framework is implemented on a CPU performance dataset using k-means, expectation maximization, farthest first, and filtered clustering algorithms. Results are analyzed and discussed to justify the proposed framework.
Performance and emission study of jatropha biodiesel and its blendsIAEME Publication
The document analyzes the performance and emissions of a compression ignition engine fueled with jatropha biodiesel blends. Physicochemical properties and performance parameters like brake thermal efficiency, brake specific fuel consumption, and emissions like exhaust temperature and smoke were tested for diesel (D100), and blends containing 10%, 20%, 30% jatropha biodiesel and 70%, 80%, 90% diesel. Test results showed brake thermal efficiency was higher for biodiesel blends at lower loads. Exhaust temperature was higher for blends but the blend with 5% hexane additive had the lowest temperature. Smoke emissions were slightly higher for blends than diesel at medium brake mean effective pressures.
Modified weighted embedding method for image steganographyIAEME Publication
This document proposes a modified weighted embedding method for image steganography. It begins by discussing traditional LSB substitution methods and their weaknesses. It then describes the proposed method, which embeds data by complementing LSBs in image pixels based on the decimal value of the data, rather than direct bit replacement. This is intended to provide better security while maintaining high image quality. The embedding algorithm works by converting the data to decimal, dividing the cover image into blocks, and complementing LSBs in the block pixels based on the decimal digits and an embedding table. Extraction works similarly but in reverse. Experiments on grayscale images are said to support the method.
Experimental studies on antioxidant properties of calotropis giganteaIAEME Publication
This study investigated the antioxidant properties of solvent extracts from Calotropis gigantea leaves, buds, and flowers. Various solvent extracts (ethanol, methanol, chloroform, aqueous) were tested for their ability to scavenge DPPH and hydrogen peroxide radicals. Many extracts showed radical scavenging activity comparable to standard antioxidants like ascorbic acid and quercetin. However, the reducing power of the extracts was lower than standards. The radical scavenging could be due to metabolites like alkaloids, tannins, and polyphenols detected in the plant. While supporting C. gigantea's traditional use, further studies are needed to better utilize its antioxidant properties.
This document summarizes research on vertical handover between UMTS and WLAN networks. It describes the architectures, algorithms and procedures involved in vertical handover. The key points are:
1. Vertical handover allows seamless switching between cellular (UMTS) and wireless local area (WLAN) networks. This provides benefits like reduced power consumption and lower costs when using WLAN connections.
2. The Universal Seamless Handover Architecture (USHA) is proposed to support both horizontal and vertical handovers with small infrastructure changes. It uses IP tunneling techniques.
3. The Smart Decision Model is used for reliable network selection. It gathers information to choose the best network interface based on factors
Risk management in banking a study with reference to state bank of india sbi aIAEME Publication
This document discusses risk management in banking with a focus on credit risk management practices at State Bank of India (SBI) and its associates. It provides an overview of SBI and its subsidiaries, and discusses how SBI has implemented the Basel accords on capital adequacy requirements and approaches credit risk measurement. The document analyzes trends in non-performing assets and capital adequacy ratios at SBI from 2007-2008 to 2012-2013 to assess its risk management practices.
Tag snp selection using quine mc cluskey optimization method-2IAEME Publication
This document summarizes a research paper that proposes using the Quine-McCluskey optimization method to select tag SNPs. The paper begins with background on tag SNPs and linkage disequilibrium. It then provides an overview of the Quine-McCluskey method for Boolean minimization and describes how it can be applied to select a minimal set of tag SNPs that represent the variation in a larger set of SNPs. The proposed method generates minterms and prime implicants to select essential tag SNPs in a three-step process to find the minimum tag SNP set. Experimental results reportedly show the method selects a feasible and effective number of tag SNPs.
Analysis of propagation of modulated optical signal in an integrated optic enviIAEME Publication
This document analyzes the propagation of modulated optical signals in integrated optic environments. It begins by discussing how modulation distributes an optical signal's power across multiple frequency components, requiring analysis beyond the monochromatic assumption. It then models a slab waveguide numerically to show how propagation constants and mode profiles vary with frequency. Finally, it simulates the phase variations experienced by different frequency components of a modulated signal propagating through integrated optic structures like straight waveguides and bends, demonstrating their ability to support wide bandwidths.
Target costing and its in reducing the cost comparison at industrial companiIAEME Publication
This document discusses target costing and its role in reducing costs for industrial companies. It provides an abstract that outlines analyzing costing and cost reduction methods for construction firms in Libya. The document then reviews literature on target costing, describing it as a cost management tool used to reduce product costs over the entire lifecycle. It discusses principles of target costing like being price-led, focusing on customers and design, involving cross-functional teams, taking a lifecycle orientation, and engaging the value chain. The document also examines how most product costs are determined at the design stage, and how techniques like Lean Six Sigma, Just-in-Time production and Total Quality Management can help reduce waste and costs.
The influence of air gaps at 0.4 duty cycle on magnetic core type ‘e’ to in...IAEME Publication
This document summarizes research on modifying the design of a magnetic core type E used in a Cuk converter to increase efficiency. Three models of the magnetic core were tested by varying the placement of air gaps. Model 1 had air gaps on all feet, Model 2 on the left and right feet, and Model 3 on the middle and right feet. Model 3 performed best, achieving 94% efficiency with a 0.19mm gap on the middle foot and 0.254mm gap on the right foot. The document analyzes the equivalent circuits and magnetic properties of each core design to determine the optimal air gap configuration and maximize load current.
Parametric optimization for cutting speed – a statistical regression modeling...IAEME Publication
This document presents an experimental study to optimize cutting speed in wire electrical discharge machining (WEDM) of EN-31 alloy steel. Experiments were conducted using a L27 orthogonal array to investigate the effects of eight machining parameters (pulse on time, pulse off time, peak current, spark gap voltage, wire feed rate, wire tension, servo feed, and dielectric flushing pressure) on cutting speed. Analysis of variance was used to determine the most significant parameters, and the optimal levels for maximizing cutting speed were found to be pulse on time at 128 μs, pulse off time at 53 μs, peak current at 230 A, spark gap voltage at 20 V, wire feed rate at 4 m/min, wire tension at
OPTIMIZATION OF MACHINING PARAMETERS IN EDM OF CFRP COMPOSITE USING TAGUCHI T...IAEME Publication
Electrical discharge machining (EDM) is a nontraditional manufacturing technique that has been widely used in the production of tools and dies throughout the world in recent years. The most important performance measure in EDM is the surface roughness. In this study, the effect and
optimization of machining parameters on surface roughness in an EDM operation was investigated by using the Taguchi method. The experimental studies were conducted under varying gap voltage,discharge current, and pulse-on time
Optimization of machining parameters in edm of cfrp composite using taguchi t...IAEME Publication
This document summarizes a study that used the Taguchi method to optimize machining parameters for electrical discharge machining (EDM) of carbon fiber reinforced plastic (CFRP) composite material. The goal was to minimize surface roughness. Experiments were conducted varying gap voltage, discharge current, and pulse-on time. An L9 orthogonal array was used to design the experiments. Surface roughness measurements were analyzed using signal-to-noise ratios and analysis of variance to determine the most influential factors. The results showed that discharge current had the largest effect on surface roughness. Confirmation experiments validated that the optimal parameters produced results consistent with predictions.
THE EFFECT OF DIFFERENT WIRE ELECTRODES ON THE MRR OF MS WORKPIECE USING WEDM...IAEME Publication
Wire electrical discharge machining (WEDM) is a specialized thermal machining process which is capable of accurate machining of parts which have varying hardness, complex shapes and sharp edges that are hard to be machined by the traditional machining processes. . Predictions on the
Material Removal Rate of workpieces in WEDM have been reported in the past. In the present study an analysis has been done to evaluate the Material Removal Rate of MS workpiece using WEDM process with different types of wire electrodes.
Investigation on process response and parameters in wire electricalIAEME Publication
This document summarizes a study that investigated the effects of process parameters on wire electrical discharge machining (WEDM) of Inconel 625. The study used Taguchi's design of experiments methodology to determine the optimal levels of six machining parameters (pulse-on time, pulse-off time, wire feed, upper flush, lower flush, wire tension) for minimizing kerf width, electrode wire wear, and maximizing surface hardness. Twenty-five experiments were conducted according to an L25 orthogonal array. Regression analysis was used to establish relationships between the process parameters and responses. The results showed good agreement between experimental and predicted values, demonstrating the methodology can determine optimal machining conditions for WEDM of Inconel
Investigation on process response and parameters in wire electricaliaemedu
This document summarizes a study that investigated the effects of process parameters on performance measures during wire electrical discharge machining (WEDM) of Inconel 625. The study considered the effects of pulse-on time, pulse-off time, upper flush, lower flush, wire feed, and wire tension on cutting width, electrode wear, and hardness. Experiments were conducted using an orthogonal array design and relationships between the control factors and responses were established through regression analysis. The results showed good agreement between experimental and predicted values of the performance measures.
Investigation on process response and parameters in wire electrical discharge...IAEME Publication
This document summarizes a study that investigated the effects of process parameters on performance measures during wire electrical discharge machining (WEDM) of Inconel 625. The study considered the effects of pulse-on time, pulse-off time, upper flush, lower flush, wire feed, and wire tension on cutting width, electrode wear, and hardness. Experiments were conducted using an orthogonal array design and relationships between the control factors and responses were established through regression analysis. The results showed good agreement between experimental and predicted values of the performance measures.
MODELING AND OPTIMIZATION OF EDM PROCESS PARAMETERS: A REVIEWIAEME Publication
Electrical discharge machining (EDM) is one of the earliest non-traditional machining processes. EDM process is based on thermo electric energy between the work piece and an electrode. There are different input parameters which influence on the outputs such as MRR, TWR and SR.
Optimization is one of the techniques used in manufacturing sectors to arrive for the best manufacturing conditions, which is an essential need for industries towards manufacturing of quality products at lower cost.
Optimization of Process Parameters in Wire Electrical Discharge Machining of ...IJERA Editor
Wire electrical discharge machining (WEDM) is a specialized thermal machining process capable of accurately machining parts with varying hardness or complex shapes, which have sharp edges that are very difficult to be machined by the main stream machining processes. This practical technology of the WEDM process is based on the conventional EDM sparking phenomenon utilizing the widely accepted non-contact technique of material removal. Since the introduction of the process, WEDM has evolved from a simple means of making tools and dies to the best alternative of producing micro-scale parts with the highest degree of dimensional accuracy and surface finish quality. Metal matrix composites are advanced materials having high specific strength, good wear resistance, and high thermal expansion coefficient. To achieve this task, machining parameters such as pulse on time, pulse off time, peak current, servo voltage, wire feed, wire tension etc. of this process should be selected such that optimal value of their performance measures like Material Removal Rate (MRR), Surface Roughness (SR), Gap current, Dimensional deviation, etc. can be obtained or improved. In past decades, intensive research work had been carried out by different researchers for improvement and optimization of WEDM performance measures using various optimization techniques like Taguchi, Response Surface Methodology (RSM), Artificial Neural Network (ANN), Genetic Algorithm (GA), etc. This paper also highlights the feasibility of the different control strategies of obtaining the optimal machining conditions. This literature review helps to identify the suitable process parameters and their ranges in machining of metal matrix composites.
IRJET- Optimization of WEDM Process Parameters on Machining of AA6082/SiC Met...IRJET Journal
This document discusses optimizing the wire electrical discharge machining (WEDM) process parameters for machining an aluminum AA6082/silicon carbide (SiC) metal matrix composite. The objectives are to achieve the maximum material removal rate and minimum surface roughness. A Taguchi L9 orthogonal array experimental design is used to evaluate three process parameters (pulse on time, pulse off time, and peak current) at three levels each. The experiments are conducted on an AA6082/5% SiC composite fabricated using stir casting. Response variables of material removal rate and surface roughness are measured and multi-objective optimization is performed using Grey relational analysis.
Experimental Investigation to Determine Influence of Process Parameters on Su...IRJET Journal
This document summarizes an experimental investigation into determining the influence of process parameters on surface quality in wire cut electrical discharge machining (WEDM). The study examines the relationship between input process parameters like pulse-on time, pulse-off time, peak current, wire material, and workpiece material, and output variables like surface roughness and electrode wear. Experiments were conducted using an aluminum workpiece material and brass wire electrode. Based on the chosen input parameters and performance measures, a L9 orthogonal array was used to optimize the process parameters for machining aluminum alloys by WEDM.
Influence of Powder Mixed Dielectric EDM on Response Variables and Methods to...IRJET Journal
This document reviews research on powder mixed electric discharge machining (PMEDM) to improve machining characteristics like material removal rate, tool wear ratio, and surface roughness. PMEDM involves mixing conductive powder into the dielectric fluid, which decreases the fluid's insulating strength and allows for easier removal of debris during machining. The powder particles form chains between the electrodes under sparking, creating a "bridging effect" that enhances material removal. The document discusses the technology and process mechanisms of PMEDM. It then reviews literature on the effects of different process parameters and powder materials on response variables. Finally, it discusses optimization techniques like Taguchi methods and response surface methodology that have been used to analyze experimental PMEDM results.
Optimization of EDM Process Parameters using Response Surface Methodology for...ijtsrd
The present work demonstrates the optimization process of material removal rate MRR of electrical discharge machining EDM by RSM Response Surface Methodology . The work piece material was EN31 tool steel. The pulse on time, pulse off time, pulse current and voltage were the control parameters of EDM. RSM method was used to design the experiment using rotatable central composite design as this is the most widely used experimental design for modeling a second–order response surface. The process has been successfully modeled using response surface methodology RSM and model adequacy checking is also carried out using Minitab software. The second order response models have been validated with analysis of variance. Finally, an attempt has been made to estimate the optimum machining conditions to produce the best possible responses within the experimental constraints. Dr. N. Mahesh Kumar | Mr. P. Chinna Rao ""Optimization of EDM Process Parameters using Response Surface Methodology for AISI D3 Steel"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-3 , April 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23535.pdf
Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/23535/optimization-of-edm-process-parameters-using-response-surface-methodology-for-aisi-d3-steel/dr-n-mahesh-kumar
This document summarizes a study that used response surface methodology and grey-Taguchi technique to model and optimize the wire electrical discharge machining (WEDM) process. Experiments were conducted varying 6 process parameters (discharge current, pulse duration, etc.) at 3 levels. Models were developed relating the responses of material removal rate, surface finish, and kerf to the parameters. Predicted data from the models were used in a Taguchi design to find the optimal parameter combination for maximizing material removal rate and surface finish while minimizing kerf.
This document summarizes a research study that investigated near-dry electrical discharge machining (EDM) to optimize material removal rate (MRR) and surface finish. The study used a Taguchi L9 orthogonal array design of experiments to examine the effects of discharge current, pulse on time, gap voltage, and pulse off time on MRR and surface roughness. Response surface methodology was employed to optimize both responses simultaneously. The experimental results found that near-dry EDM achieved a better surface finish compared to wet EDM due to more stable machining at lower discharge energies. MRR and surface roughness were modeled as functions of the process parameters. The models showed the parameters and their interactions significantly affected MRR.
MULTI OBJECTIVE OPTIMIZATION OF NEAR-DRY EDM PROCESS USING RESPONSE SURFACE M...IAEME Publication
The correct selection of manufacturing technique is one of the most important aspects to take into consideration in the majority of manufacturing processes and particularly in processes related to Electrical Discharge Machining (EDM). It is capable of machining geometrically complex or hard
material components, which are precise and difficult-to-machine such as heat treated tool steels, composites, super alloys, ceramics, carbides, heat resistant steels etc. being widely used in die and mold making industries, aerospace, aeronautics and nuclear industries.
Optimization of Wire Cut EDM of Aluminium Alloy 6063 by using Taguchi Techniqueijtsrd
The cold work applications like aluminium extrusion, it allows complex shapes to be formed with very smooth surfaces and it is popular for visible architectural applications such as window frames, door frames, roofs, and sign frames should have high toughness, wear resistance, compressive strength, high corrosion resistance, high surface finish and complex profiles. AA 6063 is an aluminium alloy, with magnesium and silicon as the alloying elements. This material can satisfy the above requirements, because of its hardness and strength AA 6063 cannot be machined easily through traditional machining processes. Advanced machining processes are used only when there is no suitable traditional machining process to meet necessary requirements efficiently and economically. Among them wire cut EDM is employed because of its tight tolerances and high surface finish. Based on intense literature survey, it was noticed that very few works were reported on WEDM of AA 6063. As a part of our thesis, WEDM of AA 6063 is considered for the study. In this work Pulse on time, pulse off time, peak current, wire speed, wire tension and flushing pressure of dielectric medium are considered as parameters and their effect on performance measures, metal removal rate MRR and surface roughness will be studied through experimental investigation. Using Taguchi approach, considered parameters will be optimized for maximum MRR and minimum for Surface roughness separately. Taguchi method will be applied to generate mean S N ratios to identify the optimum process parameters. Kandukuri Srinivas | K. Anabayan | P. H. J. Venkatesh "Optimization of Wire Cut EDM of Aluminium Alloy 6063 by using Taguchi Technique" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-4 , June 2020, URL: https://www.ijtsrd.com/papers/ijtsrd31047.pdf Paper Url :https://www.ijtsrd.com/engineering/mechanical-engineering/31047/optimization-of-wire-cut-edm-of-aluminium-alloy-6063-by-using-taguchi-technique/kandukuri-srinivas
Multi-Response Optimization of WEDM Process Parameters of Monel 400 using Int...ijceronline
Non-traditional machining processes such as Wire Electric Discharge Machining (WEDM) are increasingly been employed to machine difficult-to-machine materials. Monel 400 an alloy of Nickel and Copper is taken in this study and it is cut through Wire Electric Discharge Machining process. It is utilized mainly in corrosion resistant applications. Further, the process parameters are optimized to get the desired machining conditions which can improve the quality of machining. Design of Experiments is done through Central Composite Design (CCD). Response Surface Methodology (RSM) and Genetic Algorithm (GA) which is an evolutionary algorithm are the techniques employed for the optimization of parameters in WEDM. The multi response optimization for achieving maximum material removal rate (MRR) and minimum surface roughness, the optimum process parameters are found to be ‘Current’ of 2.031 A, ‘T-On’ of 3 µs, ‘T-Off’ of 10 µs, the obtained maximum MRR is 6.339 mm 3 /min and minimum surface roughness is 1.846 µm.
The document discusses optimizing process parameters in wire electrical discharge machining (WEDM) of high carbon high chromium steel using Taguchi's method and utility concept. It aims to maximize material removal rate and minimize surface roughness and kerf width. An L25 orthogonal array was used to design the experiment with six process parameters each at five levels. Experiments were conducted and response variables of material removal rate, surface roughness and kerf width were measured. Signal to noise ratios were calculated for each response using Taguchi's equations. A multi-response optimization was performed using a weighted utility function to determine the optimal process parameter settings that satisfy all response objectives.
MULTI RESPONSE OPTIMISATION OF DIE SINKER EDM FOR ALSIC COMPOSITE IAEME Publication
On e of the important aspects that should be taken into consideration in the majority of manufacturing processes and, particularly, in processes related to Electrical Discharge Machining (EDM) is the correct selection of manufacturing conditions. Appropriate choice of the machining parameters and electrode material during electric discharge machining is fundamental to its performance and accuracy.
Similar to Investigation of mrr in wedm for wc co sintered composite (20)
Submission Deadline: 30th September 2022
Acceptance Notification: Within Three Days’ time period
Online Publication: Within 24 Hrs. time Period
Expected Date of Dispatch of Printed Journal: 5th October 2022
MODELING AND ANALYSIS OF SURFACE ROUGHNESS AND WHITE LATER THICKNESS IN WIRE-...IAEME Publication
White layer thickness (WLT) formed and surface roughness in wire electric discharge turning (WEDT) of tungsten carbide composite has been made to model through response surface methodology (RSM). A Taguchi’s standard Design of experiments involving five input variables with three levels has been employed to establish a mathematical model between input parameters and responses. Percentage of cobalt content, spindle speed, Pulse on-time, wire feed and pulse off-time were changed during the experimental tests based on the Taguchi’s orthogonal array L27 (3^13). Analysis of variance (ANOVA) revealed that the mathematical models obtained can adequately describe performance within the parameters of the factors considered. There was a good agreement between the experimental and predicted values in this study.
A STUDY ON THE REASONS FOR TRANSGENDER TO BECOME ENTREPRENEURSIAEME Publication
The study explores the reasons for a transgender to become entrepreneurs. In this study transgender entrepreneur was taken as independent variable and reasons to become as dependent variable. Data were collected through a structured questionnaire containing a five point Likert Scale. The study examined the data of 30 transgender entrepreneurs in Salem Municipal Corporation of Tamil Nadu State, India. Simple Random sampling technique was used. Garrett Ranking Technique (Percentile Position, Mean Scores) was used as the analysis for the present study to identify the top 13 stimulus factors for establishment of trans entrepreneurial venture. Economic advancement of a nation is governed upon the upshot of a resolute entrepreneurial doings. The conception of entrepreneurship has stretched and materialized to the socially deflated uncharted sections of transgender community. Presently transgenders have smashed their stereotypes and are making recent headlines of achievements in various fields of our Indian society. The trans-community is gradually being observed in a new light and has been trying to achieve prospective growth in entrepreneurship. The findings of the research revealed that the optimistic changes are taking place to change affirmative societal outlook of the transgender for entrepreneurial ventureship. It also laid emphasis on other transgenders to renovate their traditional living. The paper also highlights that legislators, supervisory body should endorse an impartial canons and reforms in Tamil Nadu Transgender Welfare Board Association.
BROAD UNEXPOSED SKILLS OF TRANSGENDER ENTREPRENEURSIAEME Publication
Since ages gender difference is always a debatable theme whether caused by nature, evolution or environment. The birth of a transgender is dreadful not only for the child but also for their parents. The pain of living in the wrong physique and treated as second class victimized citizen is outrageous and fully harboured with vicious baseless negative scruples. For so long, social exclusion had perpetuated inequality and deprivation experiencing ingrained malign stigma and besieged victims of crime or violence across their life spans. They are pushed into the murky way of life with a source of eternal disgust, bereft sexual potency and perennial fear. Although they are highly visible but very little is known about them. The common public needs to comprehend the ravaged arrogance on these insensitive souls and assist in integrating them into the mainstream by offering equal opportunity, treat with humanity and respect their dignity. Entrepreneurship in the current age is endorsing the gender fairness movement. Unstable careers and economic inadequacy had inclined one of the gender variant people called Transgender to become entrepreneurs. These tiny budding entrepreneurs resulted in economic transition by means of employment, free from the clutches of stereotype jobs, raised standard of living and handful of financial empowerment. Besides all these inhibitions, they were able to witness a platform for skill set development that ignited them to enter into entrepreneurial domain. This paper epitomizes skill sets involved in trans-entrepreneurs of Thoothukudi Municipal Corporation of Tamil Nadu State and is a groundbreaking determination to sightsee various skills incorporated and the impact on entrepreneurship.
DETERMINANTS AFFECTING THE USER'S INTENTION TO USE MOBILE BANKING APPLICATIONSIAEME Publication
The banking and financial services industries are experiencing increased technology penetration. Among them, the banking industry has made technological advancements to better serve the general populace. The economy focused on transforming the banking sector's system into a cashless, paperless, and faceless one. The researcher wants to evaluate the user's intention for utilising a mobile banking application. The study also examines the variables affecting the user's behaviour intention when selecting specific applications for financial transactions. The researcher employed a well-structured questionnaire and a descriptive study methodology to gather the respondents' primary data utilising the snowball sampling technique. The study includes variables like performance expectations, effort expectations, social impact, enabling circumstances, and perceived risk. Each of the aforementioned variables has a major impact on how users utilise mobile banking applications. The outcome will assist the service provider in comprehending the user's history with mobile banking applications.
ANALYSE THE USER PREDILECTION ON GPAY AND PHONEPE FOR DIGITAL TRANSACTIONSIAEME Publication
Technology upgradation in banking sector took the economy to view that payment mode towards online transactions using mobile applications. This system enabled connectivity between banks, Merchant and user in a convenient mode. there are various applications used for online transactions such as Google pay, Paytm, freecharge, mobikiwi, oxygen, phonepe and so on and it also includes mobile banking applications. The study aimed at evaluating the predilection of the user in adopting digital transaction. The study is descriptive in nature. The researcher used random sample techniques to collect the data. The findings reveal that mobile applications differ with the quality of service rendered by Gpay and Phonepe. The researcher suggest the Phonepe application should focus on implementing the application should be user friendly interface and Gpay on motivating the users to feel the importance of request for money and modes of payments in the application.
VOICE BASED ATM FOR VISUALLY IMPAIRED USING ARDUINOIAEME Publication
The prototype of a voice-based ATM for visually impaired using Arduino is to help people who are blind. This uses RFID cards which contain users fingerprint encrypted on it and interacts with the users through voice commands. ATM operates when sensor detects the presence of one person in the cabin. After scanning the RFID card, it will ask to select the mode like –normal or blind. User can select the respective mode through voice input, if blind mode is selected the balance check or cash withdraw can be done through voice input. Normal mode procedure is same as the existing ATM.
IMPACT OF EMOTIONAL INTELLIGENCE ON HUMAN RESOURCE MANAGEMENT PRACTICES AMONG...IAEME Publication
There is increasing acceptability of emotional intelligence as a major factor in personality assessment and effective human resource management. Emotional intelligence as the ability to build capacity, empathize, co-operate, motivate and develop others cannot be divorced from both effective performance and human resource management systems. The human person is crucial in defining organizational leadership and fortunes in terms of challenges and opportunities and walking across both multinational and bilateral relationships. The growing complexity of the business world requires a great deal of self-confidence, integrity, communication, conflict and diversity management to keep the global enterprise within the paths of productivity and sustainability. Using the exploratory research design and 255 participants the result of this original study indicates strong positive correlation between emotional intelligence and effective human resource management. The paper offers suggestions on further studies between emotional intelligence and human capital development and recommends for conflict management as an integral part of effective human resource management.
VISUALISING AGING PARENTS & THEIR CLOSE CARERS LIFE JOURNEY IN AGING ECONOMYIAEME Publication
Our life journey, in general, is closely defined by the way we understand the meaning of why we coexist and deal with its challenges. As we develop the "inspiration economy", we could say that nearly all of the challenges we have faced are opportunities that help us to discover the rest of our journey. In this note paper, we explore how being faced with the opportunity of being a close carer for an aging parent with dementia brought intangible discoveries that changed our insight of the meaning of the rest of our life journey.
A STUDY ON THE IMPACT OF ORGANIZATIONAL CULTURE ON THE EFFECTIVENESS OF PERFO...IAEME Publication
The main objective of this study is to analyze the impact of aspects of Organizational Culture on the Effectiveness of the Performance Management System (PMS) in the Health Care Organization at Thanjavur. Organizational Culture and PMS play a crucial role in present-day organizations in achieving their objectives. PMS needs employees’ cooperation to achieve its intended objectives. Employees' cooperation depends upon the organization’s culture. The present study uses exploratory research to examine the relationship between the Organization's culture and the Effectiveness of the Performance Management System. The study uses a Structured Questionnaire to collect the primary data. For this study, Thirty-six non-clinical employees were selected from twelve randomly selected Health Care organizations at Thanjavur. Thirty-two fully completed questionnaires were received.
Living in 21st century in itself reminds all of us the necessity of police and its administration. As more and more we are entering into the modern society and culture, the more we require the services of the so called ‘Khaki Worthy’ men i.e., the police personnel. Whether we talk of Indian police or the other nation’s police, they all have the same recognition as they have in India. But as already mentioned, their services and requirements are different after the like 26th November, 2008 incidents, where they without saving their own lives has sacrificed themselves without any hitch and without caring about their respective family members and wards. In other words, they are like our heroes and mentors who can guide us from the darkness of fear, militancy, corruption and other dark sides of life and so on. Now the question arises, if Gandhi would have been alive today, what would have been his reaction/opinion to the police and its functioning? Would he have some thing different in his mind now what he had been in his mind before the partition or would he be going to start some Satyagraha in the form of some improvement in the functioning of the police administration? Really these questions or rather night mares can come to any one’s mind, when there is too much confusion is prevailing in our minds, when there is too much corruption in the society and when the polices working is also in the questioning because of one or the other case throughout the India. It is matter of great concern that we have to thing over our administration and our practical approach because the police personals are also like us, they are part and parcel of our society and among one of us, so why we all are pin pointing towards them.
A STUDY ON TALENT MANAGEMENT AND ITS IMPACT ON EMPLOYEE RETENTION IN SELECTED...IAEME Publication
The goal of this study was to see how talent management affected employee retention in the selected IT organizations in Chennai. The fundamental issue was the difficulty to attract, hire, and retain talented personnel who perform well and the gap between supply and demand of talent acquisition and retaining them within the firms. The study's main goals were to determine the impact of talent management on employee retention in IT companies in Chennai, investigate talent management strategies that IT companies could use to improve talent acquisition, performance management, career planning and formulate retention strategies that the IT firms could use. The respondents were given a structured close-ended questionnaire with the 5 Point Likert Scale as part of the study's quantitative research design. The target population consisted of 289 IT professionals. The questionnaires were distributed and collected by the researcher directly. The Statistical Package for Social Sciences (SPSS) was used to collect and analyse the questionnaire responses. Hypotheses that were formulated for the various areas of the study were tested using a variety of statistical tests. The key findings of the study suggested that talent management had an impact on employee retention. The studies also found that there is a clear link between the implementation of talent management and retention measures. Management should provide enough training and development for employees, clarify job responsibilities, provide adequate remuneration packages, and recognise employees for exceptional performance.
ATTRITION IN THE IT INDUSTRY DURING COVID-19 PANDEMIC: LINKING EMOTIONAL INTE...IAEME Publication
Globally, Millions of dollars were spent by the organizations for employing skilled Information Technology (IT) professionals. It is costly to replace unskilled employees with IT professionals possessing technical skills and competencies that aid in interconnecting the business processes. The organization’s employment tactics were forced to alter by globalization along with technological innovations as they consistently diminish to remain lean, outsource to concentrate on core competencies along with restructuring/reallocate personnel to gather efficiency. As other jobs, organizations or professions have become reasonably more appropriate in a shifting employment landscape, the above alterations trigger both involuntary as well as voluntary turnover. The employee view on jobs is also afflicted by the COVID-19 pandemic along with the employee-driven labour market. So, having effective strategies is necessary to tackle the withdrawal rate of employees. By associating Emotional Intelligence (EI) along with Talent Management (TM) in the IT industry, the rise in attrition rate was analyzed in this study. Only 303 respondents were collected out of 350 participants to whom questionnaires were distributed. From the employees of IT organizations located in Bangalore (India), the data were congregated. A simple random sampling methodology was employed to congregate data as of the respondents. Generating the hypothesis along with testing is eventuated. The effect of EI and TM along with regression analysis between TM and EI was analyzed. The outcomes indicated that employee and Organizational Performance (OP) were elevated by effective EI along with TM.
INFLUENCE OF TALENT MANAGEMENT PRACTICES ON ORGANIZATIONAL PERFORMANCE A STUD...IAEME Publication
By implementing talent management strategy, organizations would have the option to retain their skilled professionals while additionally working on their overall performance. It is the course of appropriately utilizing the ideal individuals, setting them up for future top positions, exploring and dealing with their performance, and holding them back from leaving the organization. It is employee performance that determines the success of every organization. The firm quickly obtains an upper hand over its rivals in the event that its employees having particular skills that cannot be duplicated by the competitors. Thus, firms are centred on creating successful talent management practices and processes to deal with the unique human resources. Firms are additionally endeavouring to keep their top/key staff since on the off chance that they leave; the whole store of information leaves the firm's hands. The study's objective was to determine the impact of talent management on organizational performance among the selected IT organizations in Chennai. The study recommends that talent management limitedly affects performance. On the off chance that this talent is appropriately management and implemented properly, organizations might benefit as much as possible from their maintained assets to support development and productivity, both monetarily and non-monetarily.
A STUDY OF VARIOUS TYPES OF LOANS OF SELECTED PUBLIC AND PRIVATE SECTOR BANKS...IAEME Publication
Banking regulations act of India, 1949 defines banking as “acceptance of deposits for the purpose of lending or investment from the public, repayment on demand or otherwise and withdrawable through cheques, drafts order or otherwise”, the major participants of the Indian financial system are commercial banks, the financial institution encompassing term lending institutions. Investments institutions, specialized financial institution and the state level development banks, non banking financial companies (NBFC) and other market intermediaries such has the stock brokers and money lenders are among the oldest of the certain variants of NBFC and the oldest market participants. The asset quality of banks is one of the most important indicators of their financial health. The Indian banking sector has been facing severe problems of increasing Non- Performing Assets (NPAs). The NPAs growth directly and indirectly affects the quality of assets and profitability of banks. It also shows the efficiency of banks credit risk management and the recovery effectiveness. NPA do not generate any income, whereas, the bank is required to make provisions for such as assets that why is a double edge weapon. This paper outlines the concept of quality of bank loans of different types like Housing, Agriculture and MSME loans in state Haryana of selected public and private sector banks. This study is highlighting problems associated with the role of commercial bank in financing Small and Medium Scale Enterprises (SME). The overall objective of the research was to assess the effect of the financing provisions existing for the setting up and operations of MSMEs in the country and to generate recommendations for more robust financing mechanisms for successful operation of the MSMEs, in turn understanding the impact of MSME loans on financial institutions due to NPA. There are many research conducted on the topic of Non- Performing Assets (NPA) Management, concerning particular bank, comparative study of public and private banks etc. In this paper the researcher is considering the aggregate data of selected public sector and private sector banks and attempts to compare the NPA of Housing, Agriculture and MSME loans in state Haryana of public and private sector banks. The tools used in the study are average and Anova test and variance. The findings reveal that NPA is common problem for both public and private sector banks and is associated with all types of loans either that is housing loans, agriculture loans and loans to SMES. NPAs of both public and private sector banks show the increasing trend. In 2010-11 GNPA of public and private sector were at same level it was 2% but after 2010-11 it increased in many fold and at present there is GNPA in some more than 15%. It shows the dark area of Indian banking sector.
EXPERIMENTAL STUDY OF MECHANICAL AND TRIBOLOGICAL RELATION OF NYLON/BaSO4 POL...IAEME Publication
An experiment conducted in this study found that BaSO4 changed Nylon 6's mechanical properties. By changing the weight ratios, BaSO4 was used to make Nylon 6. This Researcher looked into how hard Nylon-6/BaSO4 composites are and how well they wear. Experiments were done based on Taguchi design L9. Nylon-6/BaSO4 composites can be tested for their hardness number using a Rockwell hardness testing apparatus. On Nylon/BaSO4, the wear behavior was measured by a wear monitor, pinon-disc friction by varying reinforcement, sliding speed, and sliding distance, and the microstructure of the crack surfaces was observed by SEM. This study provides significant contributions to ultimate strength by increasing BaSO4 content up to 16% in the composites, and sliding speed contributes 72.45% to the wear rate
ROLE OF SOCIAL ENTREPRENEURSHIP IN RURAL DEVELOPMENT OF INDIA - PROBLEMS AND ...IAEME Publication
The majority of the population in India lives in villages. The village is the back bone of the country. Village or rural industries play an important role in the national economy, particularly in the rural development. Developing the rural economy is one of the key indicators towards a country’s success. Whether it be the need to look after the welfare of the farmers or invest in rural infrastructure, Governments have to ensure that rural development isn’t compromised. The economic development of our country largely depends on the progress of rural areas and the standard of living of rural masses. Village or rural industries play an important role in the national economy, particularly in the rural development. Rural entrepreneurship is based on stimulating local entrepreneurial talent and the subsequent growth of indigenous enterprises. It recognizes opportunity in the rural areas and accelerates a unique blend of resources either inside or outside of agriculture. Rural entrepreneurship brings an economic value to the rural sector by creating new methods of production, new markets, new products and generate employment opportunities thereby ensuring continuous rural development. Social Entrepreneurship has the direct and primary objective of serving the society along with the earning profits. So, social entrepreneurship is different from the economic entrepreneurship as its basic objective is not to earn profits but for providing innovative solutions to meet the society needs which are not taken care by majority of the entrepreneurs as they are in the business for profit making as a sole objective. So, the Social Entrepreneurs have the huge growth potential particularly in the developing countries like India where we have huge societal disparities in terms of the financial positions of the population. Still 22 percent of the Indian population is below the poverty line and also there is disparity among the rural & urban population in terms of families living under BPL. 25.7 percent of the rural population & 13.7 percent of the urban population is under BPL which clearly shows the disparity of the poor people in the rural and urban areas. The need to develop social entrepreneurship in agriculture is dictated by a large number of social problems. Such problems include low living standards, unemployment, and social tension. The reasons that led to the emergence of the practice of social entrepreneurship are the above factors. The research problem lays upon disclosing the importance of role of social entrepreneurship in rural development of India. The paper the tendencies of social entrepreneurship in India, to present successful examples of such business for providing recommendations how to improve situation in rural areas in terms of social entrepreneurship development. Indian government has made some steps towards development of social enterprises, social entrepreneurship, and social in- novation, but a lot remains to be improved.
OPTIMAL RECONFIGURATION OF POWER DISTRIBUTION RADIAL NETWORK USING HYBRID MET...IAEME Publication
Distribution system is a critical link between the electric power distributor and the consumers. Most of the distribution networks commonly used by the electric utility is the radial distribution network. However in this type of network, it has technical issues such as enormous power losses which affect the quality of the supply. Nowadays, the introduction of Distributed Generation (DG) units in the system help improve and support the voltage profile of the network as well as the performance of the system components through power loss mitigation. In this study network reconfiguration was done using two meta-heuristic algorithms Particle Swarm Optimization and Gravitational Search Algorithm (PSO-GSA) to enhance power quality and voltage profile in the system when simultaneously applied with the DG units. Backward/Forward Sweep Method was used in the load flow analysis and simulated using the MATLAB program. Five cases were considered in the Reconfiguration based on the contribution of DG units. The proposed method was tested using IEEE 33 bus system. Based on the results, there was a voltage profile improvement in the system from 0.9038 p.u. to 0.9594 p.u.. The integration of DG in the network also reduced power losses from 210.98 kW to 69.3963 kW. Simulated results are drawn to show the performance of each case.
APPLICATION OF FRUGAL APPROACH FOR PRODUCTIVITY IMPROVEMENT - A CASE STUDY OF...IAEME Publication
Manufacturing industries have witnessed an outburst in productivity. For productivity improvement manufacturing industries are taking various initiatives by using lean tools and techniques. However, in different manufacturing industries, frugal approach is applied in product design and services as a tool for improvement. Frugal approach contributed to prove less is more and seems indirectly contributing to improve productivity. Hence, there is need to understand status of frugal approach application in manufacturing industries. All manufacturing industries are trying hard and putting continuous efforts for competitive existence. For productivity improvements, manufacturing industries are coming up with different effective and efficient solutions in manufacturing processes and operations. To overcome current challenges, manufacturing industries have started using frugal approach in product design and services. For this study, methodology adopted with both primary and secondary sources of data. For primary source interview and observation technique is used and for secondary source review has done based on available literatures in website, printed magazines, manual etc. An attempt has made for understanding application of frugal approach with the study of manufacturing industry project. Manufacturing industry selected for this project study is Mahindra and Mahindra Ltd. This paper will help researcher to find the connections between the two concepts productivity improvement and frugal approach. This paper will help to understand significance of frugal approach for productivity improvement in manufacturing industry. This will also help to understand current scenario of frugal approach in manufacturing industry. In manufacturing industries various process are involved to deliver the final product. In the process of converting input in to output through manufacturing process productivity plays very critical role. Hence this study will help to evolve status of frugal approach in productivity improvement programme. The notion of frugal can be viewed as an approach towards productivity improvement in manufacturing industries.
A MULTIPLE – CHANNEL QUEUING MODELS ON FUZZY ENVIRONMENTIAEME Publication
In this paper, we investigated a queuing model of fuzzy environment-based a multiple channel queuing model (M/M/C) ( /FCFS) and study its performance under realistic conditions. It applies a nonagonal fuzzy number to analyse the relevant performance of a multiple channel queuing model (M/M/C) ( /FCFS). Based on the sub interval average ranking method for nonagonal fuzzy number, we convert fuzzy number to crisp one. Numerical results reveal that the efficiency of this method. Intuitively, the fuzzy environment adapts well to a multiple channel queuing models (M/M/C) ( /FCFS) are very well.
Enhancing Adoption of AI in Agri-food: IntroductionCor Verdouw
Introduction to the Panel on: Pathways and Challenges: AI-Driven Technology in Agri-Food, AI4Food, University of Guelph
“Enhancing Adoption of AI in Agri-food: a Path Forward”, 18 June 2024
The Role of White Label Bookkeeping Services in Supporting the Growth and Sca...YourLegal Accounting
Effective financial management is important for expansion and scalability in the ever-changing US business environment. White Label Bookkeeping services is an innovative solution that is becoming more and more popular among businesses. These services provide a special method for managing financial duties effectively, freeing up companies to concentrate on their main operations and growth plans. We’ll look at how White Label Bookkeeping can help US firms expand and develop in this blog.
High-Quality IPTV Monthly Subscription for $15advik4387
Experience high-quality entertainment with our IPTV monthly subscription for just $15. Access a vast array of live TV channels, movies, and on-demand shows with crystal-clear streaming. Our reliable service ensures smooth, uninterrupted viewing at an unbeatable price. Perfect for those seeking premium content without breaking the bank. Start streaming today!
https://rb.gy/f409dk
Prescriptive analytics BA4206 Anna University PPTFreelance
Business analysis - Prescriptive analytics Introduction to Prescriptive analytics
Prescriptive Modeling
Non Linear Optimization
Demonstrating Business Performance Improvement
SATTA MATKA DPBOSS KALYAN MATKA RESULTS KALYAN CHART KALYAN MATKA MATKA RESULT KALYAN MATKA TIPS SATTA MATKA MATKA COM MATKA PANA JODI TODAY BATTA SATKA MATKA PATTI JODI NUMBER MATKA RESULTS MATKA CHART MATKA JODI SATTA COM INDIA SATTA MATKA MATKA TIPS MATKA WAPKA ALL MATKA RESULT LIVE ONLINE MATKA RESULT KALYAN MATKA RESULT DPBOSS MATKA 143 MAIN MATKA KALYAN MATKA RESULTS KALYAN CHART
SATTA MATKA DPBOSS KALYAN MATKA RESULTS KALYAN CHART KALYAN MATKA MATKA RESULT KALYAN MATKA TIPS SATTA MATKA MATKA COM MATKA PANA JODI TODAY BATTA SATKA MATKA PATTI JODI NUMBER MATKA RESULTS MATKA CHART MATKA JODI SATTA COM INDIA SATTA MATKA MATKA TIPS MATKA WAPKA ALL MATKA RESULT LIVE ONLINE MATKA RESULT KALYAN MATKA RESULT DPBOSS MATKA 143 MAIN MATKA KALYAN MATKA RESULTS KALYAN CHART
Adani Group's Active Interest In Increasing Its Presence in the Cement Manufa...Adani case
Time and again, the business group has taken up new business ventures, each of which has allowed it to expand its horizons further and reach new heights. Even amidst the Adani CBI Investigation, the firm has always focused on improving its cement business.
Cover Story - China's Investment Leader - Dr. Alyce SUmsthrill
In World Expo 2010 Shanghai – the most visited Expo in the World History
https://www.britannica.com/event/Expo-Shanghai-2010
China’s official organizer of the Expo, CCPIT (China Council for the Promotion of International Trade https://en.ccpit.org/) has chosen Dr. Alyce Su as the Cover Person with Cover Story, in the Expo’s official magazine distributed throughout the Expo, showcasing China’s New Generation of Leaders to the World.
The Most Inspiring Entrepreneurs to Follow in 2024.pdfthesiliconleaders
In a world where the potential of youth innovation remains vastly untouched, there emerges a guiding light in the form of Norm Goldstein, the Founder and CEO of EduNetwork Partners. His dedication to this cause has earned him recognition as a Congressional Leadership Award recipient.
SATTA MATKA DPBOSS KALYAN MATKA RESULTS KALYAN CHART KALYAN MATKA MATKA RESULT KALYAN MATKA TIPS SATTA MATKA MATKA COM MATKA PANA JODI TODAY BATTA SATKA MATKA PATTI JODI NUMBER MATKA RESULTS MATKA CHART MATKA JODI SATTA COM INDIA SATTA MATKA MATKA TIPS MATKA WAPKA ALL MATKA RESULT LIVE ONLINE MATKA RESULT KALYAN MATKA RESULT DPBOSS MATKA 143 MAIN MATKA KALYAN MATKA RESULTS KALYAN CHART
❼❷⓿❺❻❷❽❷❼❽ Dpboss Matka Result Satta Matka Guessing Satta Fix jodi Kalyan Final ank Satta Matka Dpbos Final ank Satta Matta Matka 143 Kalyan Matka Guessing Final Matka Final ank Today Matka 420 Satta Batta Satta 143 Kalyan Chart Main Bazar Chart vip Matka Guessing Dpboss 143 Guessing Kalyan night
SATTA MATKA DPBOSS KALYAN MATKA RESULTS KALYAN MATKA MATKA RESULT KALYAN MATKA TIPS SATTA MATKA MATKA COM MATKA PANA JODI TODAY BATTA SATKA MATKA PATTI JODI NUMBER MATKA RESULTS MATKA CHART MATKA JODI SATTA COM INDIA SATTA MATKA MATKA TIPS MATKA WAPKA ALL MATKA RESULT LIVE ONLINE MATKA RESULT KALYAN MATKA RESULT DPBOSS MATKA 143 MAIN MATKA KALYAN MATKA RESULTS KALYAN CHART KALYAN CHART
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...BBPMedia1
Nathalie zal delen hoe DEI en ESG een fundamentele rol kunnen spelen in je merkstrategie en je de juiste aansluiting kan creëren met je doelgroep. Door middel van voorbeelden en simpele handvatten toont ze hoe dit in jouw organisatie toegepast kan worden.
Tired of chasing down expiring contracts and drowning in paperwork? Mastering contract management can significantly enhance your business efficiency and productivity. This guide unveils expert secrets to streamline your contract management process. Learn how to save time, minimize risk, and achieve effortless contract management.