Tools and Techniques for Commissioning and Maintaining PV SystemsTranscat
This course will review the tests to perform, the science behind why they are necessary, and the appropriate tools to conduct them, including digital multimeters, clamp meters, thermal imaging, insulation resistance, I-V curve tracers, irradiance meters, power quality, and solar asset management software.
Installation, Testing and Troubleshooting of TransformersLiving Online
This will provide you with practical knowledge (including tips, tricks and tools) covering the fundamentals of power transformers and their testing. It will greatly assist you in communicating more effectively with your electrical engineering colleagues. At the end of this workshop, participants will be familiar with the importance of transformer testing and their purpose, the different kinds of transformer tests and their procedures and the practical applications of principals applied in transformer operation and maintenance.
WHO SHOULD ATTEND?
This workshop will be appropriate for the following professionals:
Electrical engineers
Maintenance engineers
Maintenance supervisors
Power electricians
Power engineers
MORE INFORMATION: http://www.idc-online.com/content/installation-testing-and-troubleshooting-transformers-24
AC Circuit Breakers Routine Tests according to IEC 62271-100Ali Sepehri
AC Circuit Breakers Routine Tests according to IEC 62271-100
Article direct link: https://www.linkedin.com/pulse/ac-circuit-breakers-routine-tests-according-iec-ali-sepehri/
Tools and Techniques for Commissioning and Maintaining PV SystemsTranscat
This course will review the tests to perform, the science behind why they are necessary, and the appropriate tools to conduct them, including digital multimeters, clamp meters, thermal imaging, insulation resistance, I-V curve tracers, irradiance meters, power quality, and solar asset management software.
Installation, Testing and Troubleshooting of TransformersLiving Online
This will provide you with practical knowledge (including tips, tricks and tools) covering the fundamentals of power transformers and their testing. It will greatly assist you in communicating more effectively with your electrical engineering colleagues. At the end of this workshop, participants will be familiar with the importance of transformer testing and their purpose, the different kinds of transformer tests and their procedures and the practical applications of principals applied in transformer operation and maintenance.
WHO SHOULD ATTEND?
This workshop will be appropriate for the following professionals:
Electrical engineers
Maintenance engineers
Maintenance supervisors
Power electricians
Power engineers
MORE INFORMATION: http://www.idc-online.com/content/installation-testing-and-troubleshooting-transformers-24
AC Circuit Breakers Routine Tests according to IEC 62271-100Ali Sepehri
AC Circuit Breakers Routine Tests according to IEC 62271-100
Article direct link: https://www.linkedin.com/pulse/ac-circuit-breakers-routine-tests-according-iec-ali-sepehri/
Insulation resistance measurements are performed to verify that the state of dryness of the insulation of the various Winding , Bushings and the core are of acceptable values. In these presentation we will discuss about basic Insulation resistance test carried out in a two winding transformer.
This presentation will discuss how the use and need for voltage transformers has changed over the last twenty years. With the introduction of auto-ranging electric meters, meter technicians need to be prepared, use the appropriate tools and PPE for high capacity circuits (without VT's), as this method has become increasingly popular.
AC High voltage Air Break Disconnector Switch Routine Test According to IEC 6...Ali Sepehri
AC High voltage Air Break Disconnector Switch Routine Test According to IEC 62271-102 Standard
Article 9(09.10.2018) direct link: https://lnkd.in/gX_aVqq
Electrical Measurement Safety and Best Practices Webinar Presented by FlukeTranscat
Live one-hour, solutions-based webinar that will benefit anyone who works with live electrical equipment, whether you’re installing, testing, maintaining, monitoring, or troubleshooting. We will cover dangers, safe work practices (including PPE, test tool standards, and ratings), best practices, and good tips for keeping safety top of mind.
Insulation resistance measurements are performed to verify that the state of dryness of the insulation of the various Winding , Bushings and the core are of acceptable values. In these presentation we will discuss about basic Insulation resistance test carried out in a two winding transformer.
This presentation will discuss how the use and need for voltage transformers has changed over the last twenty years. With the introduction of auto-ranging electric meters, meter technicians need to be prepared, use the appropriate tools and PPE for high capacity circuits (without VT's), as this method has become increasingly popular.
AC High voltage Air Break Disconnector Switch Routine Test According to IEC 6...Ali Sepehri
AC High voltage Air Break Disconnector Switch Routine Test According to IEC 62271-102 Standard
Article 9(09.10.2018) direct link: https://lnkd.in/gX_aVqq
Electrical Measurement Safety and Best Practices Webinar Presented by FlukeTranscat
Live one-hour, solutions-based webinar that will benefit anyone who works with live electrical equipment, whether you’re installing, testing, maintaining, monitoring, or troubleshooting. We will cover dangers, safe work practices (including PPE, test tool standards, and ratings), best practices, and good tips for keeping safety top of mind.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Event Management System Vb Net Project Report.pdfKamal Acharya
In present era, the scopes of information technology growing with a very fast .We do not see any are untouched from this industry. The scope of information technology has become wider includes: Business and industry. Household Business, Communication, Education, Entertainment, Science, Medicine, Engineering, Distance Learning, Weather Forecasting. Carrier Searching and so on.
My project named “Event Management System” is software that store and maintained all events coordinated in college. It also helpful to print related reports. My project will help to record the events coordinated by faculties with their Name, Event subject, date & details in an efficient & effective ways.
In my system we have to make a system by which a user can record all events coordinated by a particular faculty. In our proposed system some more featured are added which differs it from the existing system such as security.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
TECHNICAL TRAINING MANUAL GENERAL FAMILIARIZATION COURSEDuvanRamosGarzon1
AIRCRAFT GENERAL
The Single Aisle is the most advanced family aircraft in service today, with fly-by-wire flight controls.
The A318, A319, A320 and A321 are twin-engine subsonic medium range aircraft.
The family offers a choice of engines
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
Vaccine management system project report documentation..pdf
'docslide.us_hv-testing.ppt
1. 1
To Be A World Class Maritime Academy
HV Course March 2007
HIGH VOLTAGE
TESTS
2. 2
To Be A World Class Maritime Academy
HV Course March 2007
Objective
• Need for periodic testing to guarantee integrity
and reliability of HV system
• Need for diagnostic test for comparative
measurement and determination of fault serenity
• Need to simulate fault conditions for
verification of system components stability
3. 3
To Be A World Class Maritime Academy
HV Course March 2007
Introduction
• The high voltage (e.g. 6.6 kV) installation
covers : the generation, main supply
• cables, switchgear, transformers, electric
propulsion (if fitted) and a few large motors e.g.
for side-thrusters and air conditioning
compressors.
4. 4
To Be A World Class Maritime Academy
HV Course March 2007
Condition of HV insulation is governed by factors such as:
• Temperature, humidity, surface condition and
operating voltage level.
• Guide by the manufacturers recommendations
when testing and maintaining HV insulation.
• Before applying an IR test to HV equipment its
power supply must be switched off, isolated,
confirmed dead by an approved live-line tester
and then earthed for complete safety in
accordance with the current EPTW regulations.
5. 5
To Be A World Class Maritime Academy
HV Course March 2007
HV Test type
• HV Test on board ship
1) -Insulation Resistance (IR) test
2) -Polarity Index (PI) Test
3) -Infrared Imaging test
4) - Circuit breaker test
5) Partial discharge test
6) BIL (Basic Insulation level) test
7) Life test
6. 6
To Be A World Class Maritime Academy
HV Course March 2007
1.0 Insulation Resistance Test (IR) Test
• For all electrical equipment the key indicator to High Voltage
Equipment Testing are:
1. its safety and
2. general condition of its insulation resistance (IR) - The IR must be
tested periodically between phases and between phases and earth.
• HV equipment that is well designed and maintained, operated within
its power and temperature ratings should have a useful insulation life
of 20 years.
• An IR test is applied with a high d.c. voltage which applies a
reasonable stress to the dielectric material (insulation).
• For 6.6 kV rated equipment, a periodical 5000 V d.c. insulation
resistance (megger) test is recommended.
• The minimum IR value is usually recommended as (kV + 1) MO
where V is the equipment voltage rating. e.g. 7.6 MO would be an
acceptable IR value for a 6.6 kV machine.
7. 7
To Be A World Class Maritime Academy
HV Course March 2007
Insulation tester
Motor
α
0
Control coil
Deflecting
coil
Permanent
magnet
Permanent
Magnet Rotor
8. 8
To Be A World Class Maritime Academy
HV Course March 2007
Procedure of IR testing
• Isolate power, test and prove the conductors are dead by a proven live-line
tester.
• The circuit is earthed
• Issue EPTW.
• It is to be ensured that the operator never touches an unearthed
conductor.
• With the megger reader is connected between conductor and earth,
the safety earth is disconnected. [The safety earth must be
reconnected before the IR tester is disconnected]
• A 5000 V dc megger tester now be applied between phases and
earth, and between phases, and the values are recorded.
• The megger test should be applied for 1 minute.
• The recommended minimum value is (KV rating of the machine +
1) MΩ.
9. 9
To Be A World Class Maritime Academy
HV Course March 2007
IR Test Procedure
• For machines with healthy insulation, an IR test result may indicate
a value up to 100 times greater than the recommended minimum.
• First the reading is checked for 1 minute and for a better test it is
checked for 10 minutes.
• The correct procedure is to connect the IR tester to the circuit under
test with the safety earth connection ON.
• The safety earth may be applied through a switch connection at the
supply circuit breaker or by a temporary earth connection local to
the test point.
• This is to ensure that the operator never touches a unearthed
conductor.
• With the IR tester now connected, the safety earth is disconnected
(using an insulated extension tool for the temporary earth).
• Now the IR test is applied and recorded.
• The safety earth is now reconnected before the IR tester is
disconnected.
• This safety routine must be applied for each separate IR test.
10. 10
To Be A World Class Maritime Academy
HV Course March 2007
IR Test Procedure
• Large currents flowing through machine windings, cables, bus-bars
and main circuit breaker contacts will cause a temperature rise due to
I2R resistive heating.
• Where overheating is suspected, e.g. at a bolted bus-bar joint in the
main switchboard, the local continuity resistance may be measured
and checked against the manufacturers recommendations or compared
with similar equipment that is known to be satisfactory.
• A normal ohmmeter is not suitable- as it will only drive a few mA
through the test circuit.
• A special low resistance tester or micro-ohmmeter must be used which
drives a calibrated current (usually I=10 A) through the circuit while
measuring the volt-drop (V) across the circuit.
• The meter calculates R from V/I and displays the test result. For a
healthy bus-bar joint a continuity of a few megerOhm) would be
expected.
11. 11
To Be A World Class Maritime Academy
HV Course March 2007
2.0 Polarity Index test (PI) Test
• A more involved IR test (the polarization index or P.I.)
is used when the insulation value may be suspect or
recorded during an annual survey.
• The P.I. value is the ratio of the IR result after 0 minutes
of testing to the value recorded after 1 minute of testing
• To apply a P.I. test over a ten minute period requires a
special IR tester that has a motor-driven generator or an
electronic converter powered from a local 220 V a.c.
supply.
• Experience shows that using polarity index method give
far more reliable figure on the condition of insulation.
12. 12
To Be A World Class Maritime Academy
HV Course March 2007
3.0 Infrared Imaging Tester
• Normally the safe testing of HV equipment requires that it is
disconnected from its power supply.
• Unfortunately, it is very difficult, impossible and unsafe to closely
observe the on-load operation of internal components within HV
enclosures.
• This is partly resolved by temperature measurement with an
recording infra-red camera.
• Electric Propulsion and High Voltage Practice Infrared image
testing. distance.
• The camera is used to scan an area and the recorded infra-red image
is then processed by a computer program to display hot-spots and a
thermal profile across the equipment.
• To examine internal components, e.g. busbar joints, a camera
recording can be made immediately after the equipment has been
switched off and isolated in accordance with an EPTW safety
procedure.
13. 13
To Be A World Class Maritime Academy
HV Course March 2007
Infrared Imaging Tester
• Alternatively, some essential equipment, e.g. a main
switchboard, can be monitored on-line using specially
fitted and approved enclosure windows suitable for
infra-red testing.
• These windows arc small apertures with a permanently
fixed steel' mesh through which the camera can view the
internal temperature from a safe position.
• An outer steel plate fixed over the window mesh
maintains the overall enclosure performance during
normal operation.
14. 14
To Be A World Class Maritime Academy
HV Course March 2007
Infrared imaging tester
• A conventional photograph of the equipment is taken
simultaneously to match the infra-red image and both
are used as part of a test report.
• Such testing is usually performed by a specialist
contractor who will prepare the test report and propose
recommendation / repair advice to the ship operator.
• Fig. 8.31 (unfortunately not in colour like the original)
gives typical results from an infra-red camera test on a
bus-bar connection.
15. 15
To Be A World Class Maritime Academy
HV Course March 2007
Test for circuit breaker
IR Test of vacuum CB
• In this on-line test, the camera recorded hot-spot temperatures
and the report recommended that this copper connection is
checked for tightness as High Voltage Equipment Testing it is
running very hot compared to that on the neighboring copper-
work.
• To test the insulating integrity of an HV vacuum-type circuit
breaker requires a special high voltage impulse test - The tester
produces a short duration voltage pulse, of typically 10 kV for a
6.6 kV circuit, which is connected across the open breaker
contacts.
• Any weakness in the insulating strength of the vacuum in the
interrupter chamber will be detected as a current flow and the
tester will display the condition as a pass.
16. 16
To Be A World Class Maritime Academy
HV Course March 2007
Test for circuit breaker
IR Test of vacuum sf6
• Gas (SF6) HV circuit breakers rely on the quality and pressure of
the gas acting as the insulation between the contacts.
• A falling gas pressure can be arranged to initiate an alarm from
pressure switches fitted to each switching chamber.
• Normal gas pressures are typically 500 kPa or 5 bar.
• Overall circuit protection of HV equipment is supervised by co-
ordinated protective relays -These must be periodically tested to
confirm their level settings (for current, voltage, frequency etc.) and
their tripping times.
• This requires the injection of calibrated values of current and
voltage into the protective relays which is usually performed by ^
specialist contractor during a main ship survey while in dry-dock
17. 17
To Be A World Class Maritime Academy
HV Course March 2007
4. PARTIAL DISCHARGES
• Partial discharges are small electrical discharges that takes place
in a gas filled void or on the dielectric of a solid or liquid
insulation system.
• The discharges are basically small arcs that only partially bridge
the gap between phase to ground and phase to phase insulation.
• Partial discharge serves to provide an early warning of an
imminent equipment failure.
• The ultimate failure is the result of the heating effect caused by
the discharges.
• This leads to deeper pits and finally puncture the insulator
• Oil impregnated paper deteriorates very rapidly.
• Some epoxy resin insulators are moderately resistant.
• Porcelain, ceramics and glasses are practically immune to partial
discharges
18. 18
To Be A World Class Maritime Academy
HV Course March 2007
ACCEPTABLE LIMIT OF PARTIAL DISCHARGES
• To except zero discharges is not practical and it
is generally acceptable to accept a maximum
limit for partial discharges.
• Experience has shown that a discharge of less
than 10 pico coulombs at 0.75% of line to
ground voltage is acceptable.
• [Ref: Page 252, High Voltage Circuit Breakers by Ruben D. Garzon]
19. 19
To Be A World Class Maritime Academy
HV Course March 2007
Partial Discharge and Dielectric Strength
• The term ‘Dielectric Strength’ is used to describe the capacity of
an insulating material to withstand electrical stresses. It is not a
constant value.
• The dielectric strength of a material is considerably influenced by
numerous parameters- temperature, form and frequency of
voltage, field distribution, size of the stressed volume, duration
of stress, etc.
• If the dielectric strength of a cable insulation specified under
definite conditions is exceeded, discharge processes always
occur, and these can be divided into two categories; partial
discharges and complete break down.
• Dielectric Strength: The Potential gradient necessary to cause
breakdown of an insulating medium is termed its dielectric
strength and is usually expressed in MVs/meter of thickness.
20. 20
To Be A World Class Maritime Academy
HV Course March 2007
Dielectric Strength of different insulation materials
If thickness of the insulation material is 1 mm.
Air- 4.46 MV/m
Mica- 61 MV/m
Glass (density)- 28.5 MV/m
Ebonite- 50 MV/m
Paraffin-waxed paper- 40-60 MV/m
Transformer oil- 200 MV/m
Ceramics- 50 MV/m
Ref: Page 119, Hughes Electrical Techonology
SF6 = About twice of Air
21. 21
To Be A World Class Maritime Academy
HV Course March 2007
PARTIAL DISCHARGE IN INSULATION OF THE HIGH VOLTAGE CABLES.
• The occurrence of partial discharge (PD) within a dielectric -means
that either the electric field or the dielectric strength or both are
distributed in a highly inhomogeneous manner.
Referring figure 1:
• Gases usually have a considerably lower dielectric strength than
solid, liquid or impregnated dielectrics.
• Field strength inside the void (εr=1) exceeds the stress in
surrounding dielectric by a factor of nearly εri, the permittivity of
the insulation material.
• As a result, discharges occur in the void above a definite voltage
that can be measured externally and can lead to a gradual erosion of
the surrounding material.
22. 22
To Be A World Class Maritime Academy
HV Course March 2007
CONTINUED
• The figure below shows an example: a gas-filled cavity in the dielectric
that disturbs both the field pattern and the distribution of the dielectric
strength.
Field Strength in void increased
(doubled)
Fig: 1
23. 23
To Be A World Class Maritime Academy
HV Course March 2007
Simplified relationship between Electric stress and relative permittivity or dielectric constant
In such an arrangement of this type, the electrical field strength E of
neighboring individual components behaves as inversely proportional to
the relative dielectric constants εr.
That is if relative permittivity is less Electrical Stress goes high (V/m).
Ref: Page 40, Cable Systems for High and Extra-High Voltage by E. Peschke, R. von
Olshausen.
Fig: 2
24. 24
To Be A World Class Maritime Academy
HV Course March 2007
Partial discharge test on polymer-insulated cable
• The best way to explain the processes
taking place here is by using the simplified
equivalent circuit diagram comprising three
capacitances representing the void itself,
the dielectric connected in series with it
and the intact dielectric connected in
parallel with them both.
• Parallel to the void the equivalent circuit
diagram provides a spark gap which breaks
down when a specific voltage Uz, assumed
to be constant, is exceeded, and thus has
the effect of discharging the capacitor. This
results in repeated voltage collapses at
capacitor C1 as indicated in the
oscillogram.
C1
C2
C3
C1
C2
C3
Display
unit
25. 25
To Be A World Class Maritime Academy
HV Course March 2007
Test on Cables for partial discharge
Test voltage
Voltage at void without
discharge
Voltage at void with
discharges
C1
C2
C3
Transform
er
Display
unit
Insulation under
test
26. 26
To Be A World Class Maritime Academy
HV Course March 2007
On-site partial discharge monitoring
• It is available for the accessories,
particularly joints, and only where
they are equipped with sensors.
• Inductive Coupler: Pulses from
the joint that is being monitored
pass through Rogowiski coils in
opposite directions and, in
summation, produces a signal
with almost twice the amplitude
because the winding in the coil in
in opposite directions.
• For the same reason, pulses that
originate from the right or left of
the joint and are consequently
passing through the coils in the
same direction are largely
cancelled out during summation.
Signal
addition
Rogwisky Coil
+ -
Joint
27. 27
To Be A World Class Maritime Academy
HV Course March 2007
5.0 Basic Impulse Insulation Level (BIL) TEST
• Insulation can withstand very high voltage, if it is applied for a
very brief period.
• If a 60 Hz sinusoidal voltage between the insulation and ground
is applied and if the voltage is slowly increased, a point will be
reached where break down occurs
• On the other hand if we apply a dc impulse voltage for a
extremely short period, it takes much higher voltage before
insulation breaks down.
• Same happens with other insulators, bushing, etc.
• In the interest of standardization, and to enable a comparison
between the impulse withstand capability of insulators, the
insulators are tested by a defined impulse wave as follows.
28. 28
To Be A World Class Maritime Academy
HV Course March 2007
CONTINUED
0%
100%
50%
Time
1.2μs 50μs
1.2 X 50 μs BIL Puse
Peak voltage
29. 29
To Be A World Class Maritime Academy
HV Course March 2007
CONTINUED
• The BIL of a device is usually several times higher than its normal ac
operating voltage.
• For example, the standards require that 69 kV distribution transformer
must have a BIL of 350 kV.
• The peak voltage at which a safety begins to conduct must always be
lower than the BIL of the apparatus it is intended to protect.
• A 3 phase, 69 kV transmission line having a BIL of 300 kV is
supported on steel towers and protected by a circuit breaker. The
ground resistance at each tower is 20Ω whereas the neutral of the
transmission line is solidly grounded at the transformer just ahead of
the circuit breaker. During an electric storm, one of the towers is hit
by a lightning stroke of 20 kA.
• Calculate the voltage across each insulator string under normal
conditions.
• Describe the sequence of events during and after the lightening stroke.
30. 30
To Be A World Class Maritime Academy
HV Course March 2007
CONTINUED
• Under normal condition:
• Line to neutral voltage= 69/√3 = 40kV
• The insulator is therefore at the same potential to the
ground.
• When lightening strikes:
• Voltage across the insulator and the ground resistance
suddenly jumps to 20kA X 20 = 400kV
• Therefore insulator burns immediately causing short
circuit in all three phases.
31. 31
To Be A World Class Maritime Academy
HV Course March 2007
6.0 Life Test
• A factory test to determine expected life.
Time to break down
Field
strength,
E
Impregnated paper
Polymer