This document provides information about different types of gears and gear maintenance. It begins with an introduction to gears, their functions, and key characteristics. It then describes various types of gears including spur gears, helical gears, bevel gears, worm gears, and others. The document discusses good maintenance practices for gears such as regular inspection and cleaning oil filters. It also outlines different modes of potential gear failure including wear, scoring, pitting, and abrasive wear and their causes and remedies.
Bearing failure and its Causes and Countermeasuresdutt4190
A brief review about bearing and failure of its various parts due to other possibilities than design such as manufacturing, improper service and handling and other similar aspects.
Definition, Use, Types of beariings, Types of Journal bearing, Materials for journal bearing, Failures of journal bearing, Design terms for journal bearing, Types of roller contact bearing, applications of roller contact bearing, Designation of roller contact bearing, Design terms for roller contact bearing, comparison between journal and roller bearings, characteristics of bearings, selection procedure of bearings
Bearing failure and its Causes and Countermeasuresdutt4190
A brief review about bearing and failure of its various parts due to other possibilities than design such as manufacturing, improper service and handling and other similar aspects.
Definition, Use, Types of beariings, Types of Journal bearing, Materials for journal bearing, Failures of journal bearing, Design terms for journal bearing, Types of roller contact bearing, applications of roller contact bearing, Designation of roller contact bearing, Design terms for roller contact bearing, comparison between journal and roller bearings, characteristics of bearings, selection procedure of bearings
Chain drive is a type of transmitting mechanical power from one point to another. It is frequently used to transmit power to the wheels of a vehicle, especially bicycles and motorcycles. It is also utilized in a wide variety of machines besides vehicles.
Chain drive is a type of transmitting mechanical power from one point to another. It is frequently used to transmit power to the wheels of a vehicle, especially bicycles and motorcycles. It is also utilized in a wide variety of machines besides vehicles.
Room 14's Assembly. During term 2 we learnt about Minibeasts. We researched and wrote information reports about a variety of Minibeasts. For our assembly we read out the information and performed a song and dance to 'The Ugly Bug Ball'.
presentation is divided into three parts,
1)spur gears failure
2)Beam Strength while designing spur gears
3)Wear Strength while designing spur gears
this is not all for spur gears,just a part of design
Diesel Engine Lubrication and Lube Oil Contamination ControlMd. Moynul Islam
This presentation is intended share knowledge specially about Diesel Engine Lubrication and How the Lube Oil get Contaminated and How to Control Contamination to protect Engine Components from damaging. Still the presentation is under development. Expecting suggestions/recommendations from viewers for further up gradation of this presentation.
Dressing method of superhard grinding wheelAnna Wong
Diamond dressing rollers are widely used in grinding processes and workpieces. Such as profile forming grinding (with core and without core), internal profile, thread profile, flat profile, guide plate, multi-key shaft and gear. method of using a rotary tool in which the work surface is inlaid or covered with many small particles of diamond to cut-in the dressing wheel.
This presentation contains a simplified explanation of tribology in Piston-Cylinder System. Description of working conditions, material requirement and wear types are provided.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Runway Orientation Based on the Wind Rose Diagram.pptx
Different types of gear & maintenance By Md. Raijul Islam
1. Welcome to My Presentation
Different types of Gear & Maintenance of
Gear
2. Made By
Md. Raijul Islam
Dept. of Textile Engineering
BGMEAuniversity of Fashion&
Technology(BUFT)
Session: 2013-2017
Email: raijulbuft@gmail.com
3. 3
Gear
A gear is a Mechanical component used to
transmit power and motion
Key operations
Reversing the direction of rotation
Altering angular orientation of rotary motion
Convert rotary motion into linear motion &
vice versa
Altering speed ratios
4. 4
Characteristics
In geometry gears are
Toothed wheels
Transmit motion & power from one shaft to
another when they are closer to each other (not
too far apart)
Constant velocity ratio is desired
In comparison with belt, chain & friction
devices are : More compact
Operate at high speeds
Precise timing
Large power
5. 5
Characteristics (Contd)
Gears can mesh with any component having
compatible teeth
Gears of unequal (sizes) diameters can be
combined to produce mechanical advantage
Rotational speed & torque of second gear may
be different from that of the first
6. 6
In a set of gears, the smaller gear is called a
pinion
The larger gear is called a wheel or simply
gear
Characteristics(Contd)
9. Spur Gear
Spur gears
Most common
type
Transfer
power between
parallel shafts
Good
mechanical
efficiency
Cheapest
10. Helical Gear
Helical gears
Variation of spur
gears
Teeth are slanted
at an angle
Allowing more
teeth coming in
contact with each
other
Wide load
distribution
Less noise
12. Bevel Gear
Bevel gears
Connect two
intersecting shafts
Making an angle
with one another
Slightly less
efficient than spur
gear
More expensive
Noisy at high speed
14. Worm Gear
Worm & worm gear
Shafts are generally
but not necessarily at
right angles in
different planes
Axes are orthogonal
to each other but not
intersecting
Expensive
Efficiency drops off
quickly as gear ratio
increases
15. Rack and Pinion
Rack & pinion
arrangement
Convert
rotational motion
into translational
motion
18. Sprockets
• Sprockets are used to run chains
or belts. They are typically used in
conveyor systems.
• They are used in chain drives, in
motorcycles and bicycles.
19. Good Maintenance Practice
During normal periods of operation, gear-drive
units should be given daily routine inspection,
consisting of visual inspection and observation for
oil leaks or unusual noises. If oil leaks are evident,
the unit should be shut down until the cause of the
noise has been determined and corrected. Check
all oil levels at least once a week. Under normal
conditions, the maximum operating temperature
should not exceed 180F (82C). Generally,
pressure-lubricated units are equipped with a filter
which should be cleaned periodically.
20. Gear failure can occur in various modes. In this chapter details of failure are given. If care is
taken during the design stage itself to prevent each of these failure a sound gear design can
be evolved. The gear failure is explained by means of flow diagram in Fig.
GEAR TOOTH FAILURE
Different modes of failure
21. Wear on Gear
Wear is a general term describing loss of material from the
contacting surfaces of gear teeth.
• Maintenance:A certain
amount of smoothing and
polishing is expected
during “running-in” of new
gearsets.
22. Scoring is due to combination of two distinct activities: First, lubrication failure in the
contact region and second, establishment of metal to metal contact. Later on,
welding and tearing action resulting from metallic contact removes the metal rapidly
and continuously so far the load, speed and oil temperature remain at the same
level. The scoring is classified into initial, moderate and destructive.
INITIAL SCORING
Initial scoring occurs at the high
spots left by previous machining.
Lubrication failure at these spots
leads to initial scoring or scuffing as
shown in Fig. (h). Once these high
spots are removed, the stress
comes down as the load is
distributed over a larger area. The
scoring will then stop if the load,
speed and temperature of oil remain
unchanged or reduced. Initial
scoring is non-progressive and has
corrective action associated with it. Fig. (h) Initial scoring
SCORING
23. MODERATE SCORING
After initial scoring if the
load, speed or oil
temperature increases,
the scoring will spread
over to a larger area. The
Scoring progresses at
tolerable rate. This is
called moderate scoring
as shown in Fig. (i).
Fig. (i) Moderate scoring
SCORING
24. DESTRUCTIVE SCORING
After the initial scoring, if
the load, speed or oil
temperature increases
appreciably, then severe
scoring sets in with heavy
metal torn regions
spreading quickly
throughout as shown in
Fig.(j). Scoring is normally
predominant over the pitch
line region since
elastohydrodynamic
lubrication is the least at
that region. In dry running
surfaces may seize.
Fig. (j) Destructive scoring
SCORING
25. Cause:
• Excessive surface pressure.
• High Surface Speed.
• Inadequate supply of lubricant result in the breakdown of the oil film.
Remedies:
• Selecting the parameters such as surface speed, surface pressure and
the flow of lubricant in such a way that the resulting temperature at the
contacting surfaces is within permissible limits.
• The bulk temperature of the lubricant can be reduced by providing fins
on the outside surface of the gear box and a fan for forced circulation
of air over the fins.
SCORING
26. Pitting is a surface fatigue failure of the gear tooth. It
occurs due to repeated loading of tooth surface and the
contact stress exceeding the surface fatigue strength of
the material. Material in the fatigue region gets removed
and a pit is formed. The pit itself will cause stress
concentration and soon the pitting spreads to adjacent
region till the whole surface is covered. Subsequently,
higher impact load resulting from pitting may cause
fracture of already weakened tooth. However, the failure
process takes place over millions of cycles of running.
There are two types of pitting, initial and progressive.
PITTING OF GEARS
27. INITIAL / INCIPIENT PITTING
Initial pitting occurs during running-in
period wherein oversized peaks on the
surface get dislodged and small pits of
25 to 50 μm deep are formed just below
pitch line region. Later on, the load gets
distributed over a larger surface area
and the stress comes down which may
stop the progress of pitting.
Fig. (e) Initial pitting
PITTING OF GEARS
28. In the helical gear shown in Fig. (e). pitting started as a
local overload due to slight misalignment and progressed
across the tooth in the dedendum portion to mid face.
Here, the pitting stopped and the pitted surfaces began to
polish up and burnish over. This phenomenon is common
with medium hard gears. On gears of materials that run in
well, pitting may cease after running in, and it has
practically no effect on the performance of the drive since
the pits that are formed gradually become smoothed over
from the rolling action. The initial pitting is non-
progressive.
PITTING OF GEARS
29. Cause:
• Errors in tooth profile.
• Surface irregularities.
• Misalignment.
Remedies:
• Precise machining of gears.
• Correct alignment of gears.
• Reducing the dynamic loads.
Initial Pitting:
PITTING OF GEARS
30. Pitting begins on the tooth
flanks near the line along
the tooth passing through
the pitch point where there
are high friction forces due
to the low sliding velocity.
Then it spreads to the
whole surface of the flank.
Tooth faces are subjected to
pitting only in rare cases.
Fig. (f) shows how in
destructive pitting, pitting
has spread over the whole
tooth and weakened tooth
has fractured at the tip
leading to total failure
Fig. (g) Whole tooth is destroyed by extensive pitting
PITTING OF GEARS
31. Cause:
• Load on the gear tooth exceeds the surface
endurance strength of the material.
Remedies:
• Designing the gears in such a way that the
wear strength of the gear tooth is more than
the sum of static and dynamic loads.
• The surface endurance strength can be
improved by increasing the surface hardness.
Destructive Pitting:
PITTING OF GEARS
32. Abrasive wear is the principal reason for the failure of open gearing and closed gearing of
machinery operating in media polluted by abrasive materials. Examples are mining
machinery; cement mills; road laying, building construction, agricultural and transportation
machinery, and certain other machines. In all these cases, depending on the size, shape and
concentration of the abrasives, the wear will change. Abrasive wear is classified as mild and
severe.
MILD ABRASION
Mild abrasion is noticed when there is ingress of fine dust particles in lubricating oil
which are abrasive in nature. Since abrasive is very fine, the rate of metal removal is
slow. It takes a long time for perceptible wear.
Fig (a) Mild abrasion
ABRASIVE WEAR
33. The surface appears as though it is polished. A spiral bevel pinion with mild abrasion is
shown in Fig. (a) Mild abrasive wear is faced in cement mills, ore grinding mills. Fine
dust particles entering the lubricating medium cause three body abrasions. The prior
machining marks disappear and surface appears highly polished as shown in Fig.(b).
Noticeable wear occurs only over a long time. Sealing improvement and slight
pressurization of the gear box with air can reduce the entry of dust particles and
decrease this wear.
Fig. (b) Mild abrasion
ABRASIVE WEAR
34. Cause:
• Foreign particles in the lubricant like dirt,
rust, weld spatter or metallic debris can
scratch the tooth surface.
Remedy:
• Provision of oil filters.
• Increasing surface hardness.
• Use of high viscosity oils.
ABRASIVE WEAR
35. SEVERE ABRASION
This wear occurs due to ingress of larger abrasive particles in the lubricating medium
and higher concentration of the particles. The particles will plough a series of groove on
the surface in the direction of sliding on the gear tooth as seen in the Fig. (c). High rate
of wear in this case will quickly reduce the tooth thickness. Thinned tooth may later on
fracture leading to total failure.
Fig. (c) Severe abrasion
ABRASIVE WEAR
36. Miscellaneous tooth-surface
deteriorations
Burning can result in severe wear and
surface deterioration of the previously
described types owing to loss of
hardness from high temperatures.
Remedy:
To reduce friction, look first to the
lubricant.
Extreme pressure lubricants will
eliminate gear-tooth burning.
37. Corrosive wear is due to the chemical action of the lubricating oil or the additives.
Tooth is roughened due to wear and can be seen in the Fig.(d1). Chemical wear of
flank of internal gear caused by acidic lubricant is shown in Fig. (d2)
(d1)
(d2)
Fig. d Corrosive wear
CORROSIVE WEAR
38. Cause: Corrosive of the tooth is caused by
corrosive elements such as
• Extreme pressure additives present in lubricating
oils.
• Foreign materials.
Remedies:
• Providing complete enclosure for the gears free
from external contamination.
• Selecting proper additives.
• Replacing the lubricating oil at regular intervals.
CORROSIVE WEAR
39. CONCLUSION
Maintenance of gear drives involves proper selection, proper
installation, proper loading of the unit,proper lubrication, and
periodic inspection. Metallic gears have tremendous service
life when properlyused and cared for.