Details on:
Power Generation Market
Shipbuilding and Repair
Chemical Processing
Water/Waste Water
Nuclear
Petro Chemical / Refinery Market
Heat Exchanger
06 eurammon natural refrigeration award 2017_peng gao_f3Katarina Lisci
The document summarizes a presentation given by Peng Gao on an exhaust waste heat-driven sorption freezing system for refrigerated trucks. The system uses a novel two-stage solid sorption freezing cycle with MnCl2 and CaCl2 sorption beds to provide refrigeration for trucks using waste heat from the engine exhaust. Laboratory tests showed the system can achieve a maximum refrigeration capacity of 2.46 kW and minimum temperature of -25°C. Field tests on a refrigerated truck showed the system met the refrigeration requirements for transporting fresh and some frozen foods using only the engine exhaust heat for driving the sorption cycle.
The document discusses a six stroke engine, which has two power strokes compared to the one power stroke of a conventional four stroke engine. It works by using the heat from the four stroke cycle to power an additional expansion and exhaust stroke. This extracts more energy and improves efficiency over a four stroke engine. The six stroke engine requires modifications like a divided fuel/water tank, thermal resistant materials, a modified camshaft, and a water injector system. Analysis shows lower fuel usage, reduced emissions, and up to 50% higher thermal efficiency compared to a four stroke engine, but it also has limitations like cold starting issues and higher manufacturing costs.
Kovis uses ANSYS software in the development cycle of its products. ANSYS allows Kovis to verify existing designs, optimize new designs, and analyze components like brake discs and axle boxes. For brake discs, ANSYS is used to simulate ventilation, heat dissipation, stresses, and more to lower mass and improve life cycle. Topology optimization and CFD are used to optimize cooling fin shape on axle discs. For axle boxes, topology optimization reduced the casting weight by 13%. Kovis plans to continue using ANSYS for weight optimization, fatigue analysis, and developing new products.
The document summarizes a presentation given at the eurammon Symposium 2017 about using R290 and R1270 refrigerants in commercial refrigeration systems. It discusses the properties of R290 and R1270 and their impacts on system design criteria, such as lower pressure drops and mass flows compared to R22 and HFCs. It also addresses the influence of hydrocarbons on compressor lubrication, such as stronger oil dilution, and measures needed for reliable operation like minimum refrigerant charges and suction superheating. Outdoor chiller/heat pump units using R290/R1270 blends are presented as a promising future solution.
This document summarizes a presentation on the design of an ammonia-water absorption chiller for low grade waste heat recovery. The presentation discusses:
1) The objectives of designing a simple and compact absorption chiller using plate heat exchangers, a direct expansion evaporator, and a falling film absorber.
2) The development of a numerical model to simulate the chiller's performance and identify optimal design parameters.
3) The design, construction, and testing of a prototype chiller that achieved comparable COP values to commercial chillers during testing with waste heat.
The document summarizes a presentation given by Frigopol Kälteanlagen GmbH and Alpiq InTec West AG on water- and air-cooled chillers using propane (R-290) as the refrigerant. Frigopol and Alpiq have collaborated since 2014 to develop chiller solutions using natural refrigerants, focusing on a range between 20KW to 1.5MW that can use R-290 from 20KW to 340KW. The presentation outlines the phase down scenario for refrigerants in Europe, technical features of R-290 chillers including their safety concepts, examples of water-cooled chillers and applications, and a case study of an R-290 chiller installation for
Compression is a process that contains smart engineering. Absorption or compression refrigeration? Refrigerant condenser or evaporator? You choose. Feel free to have a look. We are ready to help you!
This document summarizes the current legal framework for refrigerants in Switzerland. It discusses the Chemical Risk Reduction Ordinance (ORRChem) which prohibits certain refrigerants based on capacity and charge size. A working group is revising the ORRChem based on technological developments to restrict HFCs further by 2019. The state of alternative refrigerant technologies like ammonia, CO2, and hydrocarbons is being determined to inform the revisions. Exemptions can be requested for systems that cannot meet standards with non-HFC refrigerants.
06 eurammon natural refrigeration award 2017_peng gao_f3Katarina Lisci
The document summarizes a presentation given by Peng Gao on an exhaust waste heat-driven sorption freezing system for refrigerated trucks. The system uses a novel two-stage solid sorption freezing cycle with MnCl2 and CaCl2 sorption beds to provide refrigeration for trucks using waste heat from the engine exhaust. Laboratory tests showed the system can achieve a maximum refrigeration capacity of 2.46 kW and minimum temperature of -25°C. Field tests on a refrigerated truck showed the system met the refrigeration requirements for transporting fresh and some frozen foods using only the engine exhaust heat for driving the sorption cycle.
The document discusses a six stroke engine, which has two power strokes compared to the one power stroke of a conventional four stroke engine. It works by using the heat from the four stroke cycle to power an additional expansion and exhaust stroke. This extracts more energy and improves efficiency over a four stroke engine. The six stroke engine requires modifications like a divided fuel/water tank, thermal resistant materials, a modified camshaft, and a water injector system. Analysis shows lower fuel usage, reduced emissions, and up to 50% higher thermal efficiency compared to a four stroke engine, but it also has limitations like cold starting issues and higher manufacturing costs.
Kovis uses ANSYS software in the development cycle of its products. ANSYS allows Kovis to verify existing designs, optimize new designs, and analyze components like brake discs and axle boxes. For brake discs, ANSYS is used to simulate ventilation, heat dissipation, stresses, and more to lower mass and improve life cycle. Topology optimization and CFD are used to optimize cooling fin shape on axle discs. For axle boxes, topology optimization reduced the casting weight by 13%. Kovis plans to continue using ANSYS for weight optimization, fatigue analysis, and developing new products.
The document summarizes a presentation given at the eurammon Symposium 2017 about using R290 and R1270 refrigerants in commercial refrigeration systems. It discusses the properties of R290 and R1270 and their impacts on system design criteria, such as lower pressure drops and mass flows compared to R22 and HFCs. It also addresses the influence of hydrocarbons on compressor lubrication, such as stronger oil dilution, and measures needed for reliable operation like minimum refrigerant charges and suction superheating. Outdoor chiller/heat pump units using R290/R1270 blends are presented as a promising future solution.
This document summarizes a presentation on the design of an ammonia-water absorption chiller for low grade waste heat recovery. The presentation discusses:
1) The objectives of designing a simple and compact absorption chiller using plate heat exchangers, a direct expansion evaporator, and a falling film absorber.
2) The development of a numerical model to simulate the chiller's performance and identify optimal design parameters.
3) The design, construction, and testing of a prototype chiller that achieved comparable COP values to commercial chillers during testing with waste heat.
The document summarizes a presentation given by Frigopol Kälteanlagen GmbH and Alpiq InTec West AG on water- and air-cooled chillers using propane (R-290) as the refrigerant. Frigopol and Alpiq have collaborated since 2014 to develop chiller solutions using natural refrigerants, focusing on a range between 20KW to 1.5MW that can use R-290 from 20KW to 340KW. The presentation outlines the phase down scenario for refrigerants in Europe, technical features of R-290 chillers including their safety concepts, examples of water-cooled chillers and applications, and a case study of an R-290 chiller installation for
Compression is a process that contains smart engineering. Absorption or compression refrigeration? Refrigerant condenser or evaporator? You choose. Feel free to have a look. We are ready to help you!
This document summarizes the current legal framework for refrigerants in Switzerland. It discusses the Chemical Risk Reduction Ordinance (ORRChem) which prohibits certain refrigerants based on capacity and charge size. A working group is revising the ORRChem based on technological developments to restrict HFCs further by 2019. The state of alternative refrigerant technologies like ammonia, CO2, and hydrocarbons is being determined to inform the revisions. Exemptions can be requested for systems that cannot meet standards with non-HFC refrigerants.
The Varkaus campus Energy Research Centre of Savonia University of Applied Sciences conducts energy research and testing services. It has facilities to test the combustion and emissions of various fuels in fluidized bed and grate boilers. This includes a 300kW fluidized bed boiler and a 500kW pyrolysis oil burner system. The Centre also provides material testing, corrosion testing, fuel analyses, and training services. It aims to contribute to the energy expertise in the region and support energy companies.
This document summarizes Daniel McDougall's presentation on small applications with ammonia at the eurammon Symposium 2017. It discusses traditional pumped recirculation ammonia systems and defines low charge systems as those requiring less than 1.3kg/kW of refrigerant. Case studies of various refrigeration systems show their refrigerant charges ranging from 0.65kg/kW to 3.1kg/kW. The presentation introduces low charge ammonia condensing units with capacities from 70kW to 350kW and charges less than 0.65kg/kW. It concludes that low charge ammonia is already available and possible to reduce charges by over 75%, and regulation is driving increased interest in
The HEATMAX system is an instantaneous hot water system that uses low-pressure steam to heat water in a compact assembly with built-in temperature control and overheat protection. It provides accurate temperature control to reduce steam consumption and lower fuel costs. The system includes components like piston valves, strainers, safety relief valves, a plate heat exchanger, and a control panel. It uses two control loops - one for primary temperature control and another for overheat protection. Testing is done on all components and systems. HEATMAX lowers customers' fuel and electricity costs while requiring low maintenance. It is suited for applications where hot water is needed and low pressure steam is available.
This document discusses the energy efficiency and life cycle costs of ammonia (NH3) evaporative condenser systems compared to alternative refrigerant systems. It analyzes a case study of an egg production facility that uses either an R449A refrigerant system or an NH3 system. The NH3 system has a higher upfront cost of around €145,000 compared to €60,000 for the R449A system but lower operating costs of around €39,000 per year versus €49,000 per year. Over a lifespan of 15 years, the simple payback period for the higher cost NH3 system is estimated to be less than 9 years due to its energy savings. The document concludes that NH3 evaporative conden
This document summarizes the evolution of clinker cooling technology from Claudius Peters. It describes how Claudius Peters developed the first cooler with a capacity of 500 tons per day in the 1950s and now builds systems with capacities over 13,000 tons per day. It highlights the ETA Cooler system as the pinnacle of clinker cooling technology, which has highly efficient transport, optimized cooling, and dramatically reduced maintenance costs compared to previous cooler designs.
Process optimisation top energy efficiency solutions in waste energy.BRONSWERK
The AfvalEnergie Bedrijf (AEB) in Amsterdam aimed to maximize environmental efficiency in processing waste. To increase electricity production, AEB opted for a two-stage turbine with steam reheating between stages. This increased efficiency by over 30%, producing over 30% more electricity from the same fuel amount. Bronswerk supplied the reheater units and dump condenser, using innovative techniques like the High Pressure Compact Header, to provide AEB with a uniquely high efficiency incinerator.
radiator in a heat exchanger its a part of engine cooling module. manufacturing of radiator and you can go through every part used to make the radiator with the different process till leak testing.
The document summarizes the main components of an automotive cooling system, including coolant, radiator, heater core, radiator cap, water pump, thermostat, hoses, overflow bottle, and cooling fan. It describes the purpose and function of each component in transferring heat from the engine to the radiator and maintaining the engine's optimal operating temperature. The document also provides guidelines for diagnosing cooling system issues through pressure testing, checking for leaks with fluorescent dye, and inspecting other components like the radiator cap and antifreeze concentration.
A boiler is a combination of systems and equipment in which chemical energy is converted into thermal energy, which is then transferred to working fluid, so as to convert it into steam at high temperature and pressure.
Corrosion is a relevant problem caused by water in boilers. Corrosion can be of widely varying origin and nature due to the action of dissolved oxygen, to corrosion currents set up as a result of heterogeneities on metal surfaces, or to the iron being directly attacked by the water.
While basic corrosion in boilers may be primarily due to reaction of the metal with oxygen, other factors such as stresses, acid conditions, and specific chemical corrodents may have an important influence and produce different forms of attack.
The document proposes setting up a new ice plant in Bahawalpur, Pakistan with a capacity of 50 tons per day. It discusses the history of ice making technology, machinery and equipment requirements including generators, transformers and water boreholes. The plant will produce ice blocks weighing 130-150kg each. It analyzes the local market demand, target customers, distribution channels and provides a financial plan and implementation schedule for the project.
The document discusses electronic fuel injection systems used in vehicles. It describes how computers precisely control fuel injectors based on various engine parameters to maintain the correct air-fuel ratio for emissions and performance. It then provides details on different types of fuel injection systems including throttle body injection, multi-port fuel injection, and centralized port injection. Key components like fuel injectors, fuel rails, and pressure regulators are also explained.
This document outlines the facilities needed for an automotive repair shop, including repair stalls, service stalls, welding areas, electrical work areas, painting facilities, storage, and specialized equipment for tasks like locomotive and railroad car repair. It emphasizes having the proper size and number of stalls to accommodate the largest vehicles to be serviced, as well as including necessary utilities, lighting, heating and cranes in each work area. Storage is also discussed, highlighting the need for covered space for vehicle components, tools and spare parts.
IRJET-Case Study of Supercritical Boiler TechnologyIRJET Journal
This document provides a case study on supercritical boiler technology. It discusses the key differences between subcritical and supercritical boilers, including higher steam temperatures and pressures in supercritical boilers that allow for improved efficiency. Supercritical boilers require more stringent water treatment and use of specialized high-temperature materials. The design of supercritical boilers, including spiral furnace tubes, is described. Operation and maintenance considerations like water chemistry, metallurgy, and inspection are also summarized. Overall, the case study evaluates how supercritical boiler technology enables higher plant efficiency and reduced emissions compared to subcritical technology.
CFD Analysis of Exhaust Manifold of SI Engine and Comparison of Back Pressure...IOSRJMCE
Exhaust manifold is one of the most critical components of an IC Engine. The functioning of exhaust manifold is complex and is dependent on many parameters viz. back pressure, exhaust velocity, scavenging etc. In the present work, the performance of a four-stroke four cylinder gasoline engine exhaust manifold have been analysed using three different fuels - gasoline, alcohol, and LPG for the estimation of flow characteristics, thermal characteristics, and minimum back pressure. The manifold modelling is done in Creo2.0 followed by meshing and analysis in ANSYS. The LPG fuel gives minimum back pressure, temperature and velocity being approximately in the same range for all three fuels viz. gasoline, alcohol and LPG. Thus, LPG can be considered as a suitable alternative for gasoline in terms of minimum back flow in manifold.
The bowl mill uses a motor and gear system to rotate a bowl at 40-65 rpm, grinding coal into a fine powder. Hot air enters to dry the coal while heavier debris falls out of the bowl. A grinding roller assembly applies pressure and can be adjusted, while vanes inside separate finer particles from coarser ones that are returned for further grinding. Discharge valves on top can isolate the mill from the boiler for maintenance.
Evaluation Of Operation Cost For New Co Generation Plant From Different Steam...Pichai Chaibamrung
I have performed plant performance evalutation composing different steam turbine manufacturer. the effect of steam turbine performance also effect to other package on cycle such ash cooling water, drafting system and pumping system
your reccomendations are valueable for me to improve my skill.
This document summarizes the key components of an automobile cooling system and how they work together. The main components are the water pump, cooling fan, radiator, thermostat, coolant, and heater core. The water pump circulates coolant throughout the system at high volumes to regulate the engine's temperature. The cooling fan provides airflow through the radiator to dissipate heat into the atmosphere. Sensors and the engine control module monitor temperatures and control electric cooling fans and fan clutches to maintain optimal operating temperatures.
Production-integrated vacuum heat treatment systems in the automotive industryThu Nguyen
This document discusses two methods for integrating heat treatment into automotive part production lines. The first method uses a flexible, modular multi-chamber system that heat treats large batches of parts together. The second method uses a line-integrated, cycled system that heat treats individual parts directly on the production line through high-temperature carburization and single-layer loading to reduce process time and improve quality and efficiency. Both systems aim to eliminate buffers between production steps to achieve continuous one-piece flow production.
The cooling system keeps a car's engine at an optimal operating temperature of around 200 degrees Fahrenheit through a liquid cooling system. It circulates coolant throughout the engine and radiator, using a water pump and fan to force liquid through the engine and dissipate heat through the radiator. Key components include the radiator, water pump, fan, thermostat, coolant, and radiator hoses. Liquid cooling systems improved on earlier air-cooled engines by more efficiently maintaining an optimal temperature for combustion and reducing emissions and engine wear.
The document lists various piping systems, pipe fittings, valves, and specialty products available from CIB Corp, a supplier of piping, valves, and fittings. It includes materials like carbon steel, galvanized steel, stainless steel, copper, PVC, and specialty alloys. A range of fittings, valves, and accessories are provided for various pipe sizes and materials. The company has locations in San Juan, Barceloneta, and Ponce, Puerto Rico and provides seismic bracing solutions and turn-key seismic systems for nonstructural building components.
Piping Technology & Products, Inc. is an engineering company that manufactures pipe supports, expansion joints, and other fabricated products. It has over 700 employees including 75 engineers and designers, some with PhDs. The company aims to provide excellent collaboration and support to customers. It owns several subsidiary companies and has an ISO certified 450,000 square foot manufacturing facility in Houston, Texas.
The Varkaus campus Energy Research Centre of Savonia University of Applied Sciences conducts energy research and testing services. It has facilities to test the combustion and emissions of various fuels in fluidized bed and grate boilers. This includes a 300kW fluidized bed boiler and a 500kW pyrolysis oil burner system. The Centre also provides material testing, corrosion testing, fuel analyses, and training services. It aims to contribute to the energy expertise in the region and support energy companies.
This document summarizes Daniel McDougall's presentation on small applications with ammonia at the eurammon Symposium 2017. It discusses traditional pumped recirculation ammonia systems and defines low charge systems as those requiring less than 1.3kg/kW of refrigerant. Case studies of various refrigeration systems show their refrigerant charges ranging from 0.65kg/kW to 3.1kg/kW. The presentation introduces low charge ammonia condensing units with capacities from 70kW to 350kW and charges less than 0.65kg/kW. It concludes that low charge ammonia is already available and possible to reduce charges by over 75%, and regulation is driving increased interest in
The HEATMAX system is an instantaneous hot water system that uses low-pressure steam to heat water in a compact assembly with built-in temperature control and overheat protection. It provides accurate temperature control to reduce steam consumption and lower fuel costs. The system includes components like piston valves, strainers, safety relief valves, a plate heat exchanger, and a control panel. It uses two control loops - one for primary temperature control and another for overheat protection. Testing is done on all components and systems. HEATMAX lowers customers' fuel and electricity costs while requiring low maintenance. It is suited for applications where hot water is needed and low pressure steam is available.
This document discusses the energy efficiency and life cycle costs of ammonia (NH3) evaporative condenser systems compared to alternative refrigerant systems. It analyzes a case study of an egg production facility that uses either an R449A refrigerant system or an NH3 system. The NH3 system has a higher upfront cost of around €145,000 compared to €60,000 for the R449A system but lower operating costs of around €39,000 per year versus €49,000 per year. Over a lifespan of 15 years, the simple payback period for the higher cost NH3 system is estimated to be less than 9 years due to its energy savings. The document concludes that NH3 evaporative conden
This document summarizes the evolution of clinker cooling technology from Claudius Peters. It describes how Claudius Peters developed the first cooler with a capacity of 500 tons per day in the 1950s and now builds systems with capacities over 13,000 tons per day. It highlights the ETA Cooler system as the pinnacle of clinker cooling technology, which has highly efficient transport, optimized cooling, and dramatically reduced maintenance costs compared to previous cooler designs.
Process optimisation top energy efficiency solutions in waste energy.BRONSWERK
The AfvalEnergie Bedrijf (AEB) in Amsterdam aimed to maximize environmental efficiency in processing waste. To increase electricity production, AEB opted for a two-stage turbine with steam reheating between stages. This increased efficiency by over 30%, producing over 30% more electricity from the same fuel amount. Bronswerk supplied the reheater units and dump condenser, using innovative techniques like the High Pressure Compact Header, to provide AEB with a uniquely high efficiency incinerator.
radiator in a heat exchanger its a part of engine cooling module. manufacturing of radiator and you can go through every part used to make the radiator with the different process till leak testing.
The document summarizes the main components of an automotive cooling system, including coolant, radiator, heater core, radiator cap, water pump, thermostat, hoses, overflow bottle, and cooling fan. It describes the purpose and function of each component in transferring heat from the engine to the radiator and maintaining the engine's optimal operating temperature. The document also provides guidelines for diagnosing cooling system issues through pressure testing, checking for leaks with fluorescent dye, and inspecting other components like the radiator cap and antifreeze concentration.
A boiler is a combination of systems and equipment in which chemical energy is converted into thermal energy, which is then transferred to working fluid, so as to convert it into steam at high temperature and pressure.
Corrosion is a relevant problem caused by water in boilers. Corrosion can be of widely varying origin and nature due to the action of dissolved oxygen, to corrosion currents set up as a result of heterogeneities on metal surfaces, or to the iron being directly attacked by the water.
While basic corrosion in boilers may be primarily due to reaction of the metal with oxygen, other factors such as stresses, acid conditions, and specific chemical corrodents may have an important influence and produce different forms of attack.
The document proposes setting up a new ice plant in Bahawalpur, Pakistan with a capacity of 50 tons per day. It discusses the history of ice making technology, machinery and equipment requirements including generators, transformers and water boreholes. The plant will produce ice blocks weighing 130-150kg each. It analyzes the local market demand, target customers, distribution channels and provides a financial plan and implementation schedule for the project.
The document discusses electronic fuel injection systems used in vehicles. It describes how computers precisely control fuel injectors based on various engine parameters to maintain the correct air-fuel ratio for emissions and performance. It then provides details on different types of fuel injection systems including throttle body injection, multi-port fuel injection, and centralized port injection. Key components like fuel injectors, fuel rails, and pressure regulators are also explained.
This document outlines the facilities needed for an automotive repair shop, including repair stalls, service stalls, welding areas, electrical work areas, painting facilities, storage, and specialized equipment for tasks like locomotive and railroad car repair. It emphasizes having the proper size and number of stalls to accommodate the largest vehicles to be serviced, as well as including necessary utilities, lighting, heating and cranes in each work area. Storage is also discussed, highlighting the need for covered space for vehicle components, tools and spare parts.
IRJET-Case Study of Supercritical Boiler TechnologyIRJET Journal
This document provides a case study on supercritical boiler technology. It discusses the key differences between subcritical and supercritical boilers, including higher steam temperatures and pressures in supercritical boilers that allow for improved efficiency. Supercritical boilers require more stringent water treatment and use of specialized high-temperature materials. The design of supercritical boilers, including spiral furnace tubes, is described. Operation and maintenance considerations like water chemistry, metallurgy, and inspection are also summarized. Overall, the case study evaluates how supercritical boiler technology enables higher plant efficiency and reduced emissions compared to subcritical technology.
CFD Analysis of Exhaust Manifold of SI Engine and Comparison of Back Pressure...IOSRJMCE
Exhaust manifold is one of the most critical components of an IC Engine. The functioning of exhaust manifold is complex and is dependent on many parameters viz. back pressure, exhaust velocity, scavenging etc. In the present work, the performance of a four-stroke four cylinder gasoline engine exhaust manifold have been analysed using three different fuels - gasoline, alcohol, and LPG for the estimation of flow characteristics, thermal characteristics, and minimum back pressure. The manifold modelling is done in Creo2.0 followed by meshing and analysis in ANSYS. The LPG fuel gives minimum back pressure, temperature and velocity being approximately in the same range for all three fuels viz. gasoline, alcohol and LPG. Thus, LPG can be considered as a suitable alternative for gasoline in terms of minimum back flow in manifold.
The bowl mill uses a motor and gear system to rotate a bowl at 40-65 rpm, grinding coal into a fine powder. Hot air enters to dry the coal while heavier debris falls out of the bowl. A grinding roller assembly applies pressure and can be adjusted, while vanes inside separate finer particles from coarser ones that are returned for further grinding. Discharge valves on top can isolate the mill from the boiler for maintenance.
Evaluation Of Operation Cost For New Co Generation Plant From Different Steam...Pichai Chaibamrung
I have performed plant performance evalutation composing different steam turbine manufacturer. the effect of steam turbine performance also effect to other package on cycle such ash cooling water, drafting system and pumping system
your reccomendations are valueable for me to improve my skill.
This document summarizes the key components of an automobile cooling system and how they work together. The main components are the water pump, cooling fan, radiator, thermostat, coolant, and heater core. The water pump circulates coolant throughout the system at high volumes to regulate the engine's temperature. The cooling fan provides airflow through the radiator to dissipate heat into the atmosphere. Sensors and the engine control module monitor temperatures and control electric cooling fans and fan clutches to maintain optimal operating temperatures.
Production-integrated vacuum heat treatment systems in the automotive industryThu Nguyen
This document discusses two methods for integrating heat treatment into automotive part production lines. The first method uses a flexible, modular multi-chamber system that heat treats large batches of parts together. The second method uses a line-integrated, cycled system that heat treats individual parts directly on the production line through high-temperature carburization and single-layer loading to reduce process time and improve quality and efficiency. Both systems aim to eliminate buffers between production steps to achieve continuous one-piece flow production.
The cooling system keeps a car's engine at an optimal operating temperature of around 200 degrees Fahrenheit through a liquid cooling system. It circulates coolant throughout the engine and radiator, using a water pump and fan to force liquid through the engine and dissipate heat through the radiator. Key components include the radiator, water pump, fan, thermostat, coolant, and radiator hoses. Liquid cooling systems improved on earlier air-cooled engines by more efficiently maintaining an optimal temperature for combustion and reducing emissions and engine wear.
The document lists various piping systems, pipe fittings, valves, and specialty products available from CIB Corp, a supplier of piping, valves, and fittings. It includes materials like carbon steel, galvanized steel, stainless steel, copper, PVC, and specialty alloys. A range of fittings, valves, and accessories are provided for various pipe sizes and materials. The company has locations in San Juan, Barceloneta, and Ponce, Puerto Rico and provides seismic bracing solutions and turn-key seismic systems for nonstructural building components.
Piping Technology & Products, Inc. is an engineering company that manufactures pipe supports, expansion joints, and other fabricated products. It has over 700 employees including 75 engineers and designers, some with PhDs. The company aims to provide excellent collaboration and support to customers. It owns several subsidiary companies and has an ISO certified 450,000 square foot manufacturing facility in Houston, Texas.
Hawman Container Services is an ISO 9001:2008 certified manufacturing company located in Barrie, Ontario with over 120,000 square feet of manufacturing space across three locations. They have extensive engineering and manufacturing capabilities including API 650 tank design, piping system design, 3D modeling, welding, and turnkey modular fluid handling systems. Their products and services include custom fluid handling equipment, pressure vessels, API tanks, pumping systems, and structural supports for industries including oil and gas, mining, and chemical processing.
Chalmers & Kubeck, Inc. is an industrial services company with a 250,000 square foot main plant. They have 250 skilled employees working in 2 permanent shifts to provide 24/7 service and support. Services include gear manufacturing, field machining, welding and fabrication, engineered pumps, thermal spray coating, and valve sales and service. They have extensive capabilities for large scale projects including fabrication, machining, welding, and coating repair for industrial equipment.
PT&P manufactures pre-insulated pipe supports for applications such as LNG pipelines, power plants, and industrial facilities. They produce various types of supports including cryogenic and hot pipe shoes using polyurethane foam insulation. PT&P has extensive testing capabilities and provides value-added services like field installations and inspections. They aim to be a full service provider for pre-insulated pipe support systems.
The document summarizes Piping Technology & Products' capabilities in manufacturing and testing pre-insulated pipe supports. PT&P has extensive experience designing supports for applications such as LNG plants and pipelines. They have a large manufacturing facility with equipment for producing polyurethane foam insulation and assembling pipe supports. PT&P also offers on-site services and emergency engineering support.
The document provides information about Victaulic and its grooved piping systems. It summarizes that Victaulic has been in business since 1925 and invented the grooved piping system. It then describes Victaulic's products and systems for various mining applications including slurry handling, compressed air, process water, and fire protection. It highlights advantages of Victaulic systems such as faster installation, lower costs, flexibility, and ability to accommodate expansion and movement compared to traditional welded and flanged piping.
This document discusses piping, fittings, and valves used in fluid dynamics. It begins by defining common piping terminology and describing common piping materials like steel, copper, plastic, and ceramics. It then discusses factors for pipe selection like fluid type and operating conditions. Key aspects of piping design covered include material roughness, pipe sizing methods using schedules and BWG, and considerations for pipe expansion and supports. Common pipe fittings are also defined, including flanges, elbows, reducers, and flow measurement devices. Finally, the document outlines the purpose and types of valves used to control fluid flow, such as globe, ball, gate, and safety valves.
: Discover the secret to a lower coefficient of friction while permitting translational motion or movement with the supporting element. Learn about the different types of slide plates and pipe rollers used for various applications. View the design, load capabilities, and installation and maintenance guidelines for both slide plates and pipe rollers. See numerous photos featuring combinations with other critical pipe supports in order to allow for movement or a low coefficient of friction.
The document lists codes and standards related to process engineering from organizations like ASME and API. It includes codes for piping systems, fittings, valves, pumps, heat exchangers, storage tanks, and other process equipment commonly found in facilities like power plants, refineries, chemical plants, and pipelines.
Industrial Ventilation and Air Pollution ControlJohn Kleinfelter
John Kleinfelter is the Vice President of Field Services at GSM Industrial and can be reached at 717-207-7765 or 717-725-7885. GSM Industrial is located at 3249 Hempland Road, Lancaster, PA 17601.
The document discusses different types of pipes used for water supply, including their materials, sizes, joining methods, advantages and disadvantages. It covers galvanized iron pipes, PVC/plastic pipes, steel pipes, cast iron pipes, PPR pipes. For each type, the document provides details on installation, fittings available, and joining methods like screwed joints, welded joints, etc. It includes diagrams to illustrate pipe connections and joining.
Explore how Polyurethane foam is produced, from mixing polyols and isocyanates to inspecting the final product. Learn about anchor shoe testing, lateral load testing, compressive strength testing, and axial load testing.
This document provides an overview of products and services offered by a manufacturer, including: conveyor idlers and accessories; boiler engineering products; metal coatings; industrial repair services; boiler tubes; heat exchangers; filtration systems; emissions control technologies; fans; and plastic sheets and tubing. The manufacturer aims to help customers with their needs through these offerings.
1) The document provides information about a webinar on pre-insulated pipe supports including instructions for accessing the audio portion by phone or speakers.
2) It summarizes the capabilities and experience of Piping Technology & Products (PT&P) in designing, manufacturing, and testing pre-insulated pipe supports for applications such as LNG plants and pipelines.
3) PT&P uses polyurethane foam insulation and has the capability to customize supports for different pipe sizes and temperatures ranging from cryogenic to hot applications.
Explore how Polyurethane foam is produced, from mixing polyols and isocyanates to inspecting the final product. Learn about anchor shoe testing, lateral load testing, compressive strength testing, and axial load testing.
Explore how Polyurethane foam is produced, from mixing polyols and isocyanates to inspecting the final product. Learn about anchor shoe testing, lateral load testing, compressive strength testing, and axial load testing.
This document provides an overview of a company that offers various engineering services including commissioning, installation, manufacturing, procurement, project management, and concept design for bulk materials handling and processing plants. It lists reference projects and details the company's facilities, workshops, equipment, mobile assets, human resources, training programs, engineering disciplines, and quality management system.
The document provides information on power generation processes including boiler and steam turbine systems. It discusses the basics of boiler operation including the water and steam system, combustion requirements, air and flue gas system, fuel preparation and firing. It also covers steam turbine fundamentals and components of the turbine steam system including governing and control. Key aspects like thermal efficiency, major equipment, and process regulation are described for the different systems.
The document provides information on power generation processes including boiler and steam turbine systems. It discusses the basics of boiler operation including the water and steam system, combustion requirements, air and flue gas systems, fuel preparation and firing. It also covers steam turbine fundamentals and components of the turbine steam system including governing and control. Key aspects like thermal efficiency, major equipment, and process regulation are described for the different systems.
Similar to Metal Bellows Technical Construction (20)
Practical eLearning Makeovers for EveryoneBianca Woods
Welcome to Practical eLearning Makeovers for Everyone. In this presentation, we’ll take a look at a bunch of easy-to-use visual design tips and tricks. And we’ll do this by using them to spruce up some eLearning screens that are in dire need of a new look.
Fonts play a crucial role in both User Interface (UI) and User Experience (UX) design. They affect readability, accessibility, aesthetics, and overall user perception.
Technoblade The Legacy of a Minecraft Legend.Techno Merch
Technoblade, born Alex on June 1, 1999, was a legendary Minecraft YouTuber known for his sharp wit and exceptional PvP skills. Starting his channel in 2013, he gained nearly 11 million subscribers. His private battle with metastatic sarcoma ended in June 2022, but his enduring legacy continues to inspire millions.
Storytelling For The Web: Integrate Storytelling in your Design ProcessChiara Aliotta
In this slides I explain how I have used storytelling techniques to elevate websites and brands and create memorable user experiences. You can discover practical tips as I showcase the elements of good storytelling and its applied to some examples of diverse brands/projects..
Connect Conference 2022: Passive House - Economic and Environmental Solution...TE Studio
Passive House: The Economic and Environmental Solution for Sustainable Real Estate. Lecture by Tim Eian of TE Studio Passive House Design in November 2022 in Minneapolis.
- The Built Environment
- Let's imagine the perfect building
- The Passive House standard
- Why Passive House targets
- Clean Energy Plans?!
- How does Passive House compare and fit in?
- The business case for Passive House real estate
- Tools to quantify the value of Passive House
- What can I do?
- Resources
ARENA - Young adults in the workplace (Knight Moves).pdfKnight Moves
Presentations of Bavo Raeymaekers (Project lead youth unemployment at the City of Antwerp), Suzan Martens (Service designer at Knight Moves) and Adriaan De Keersmaeker (Community manager at Talk to C)
during the 'Arena • Young adults in the workplace' conference hosted by Knight Moves.
Explore the essential graphic design tools and software that can elevate your creative projects. Discover industry favorites and innovative solutions for stunning design results.
Architectural and constructions management experience since 2003 including 18 years located in UAE.
Coordinate and oversee all technical activities relating to architectural and construction projects,
including directing the design team, reviewing drafts and computer models, and approving design
changes.
Organize and typically develop, and review building plans, ensuring that a project meets all safety and
environmental standards.
Prepare feasibility studies, construction contracts, and tender documents with specifications and
tender analyses.
Consulting with clients, work on formulating equipment and labor cost estimates, ensuring a project
meets environmental, safety, structural, zoning, and aesthetic standards.
Monitoring the progress of a project to assess whether or not it is in compliance with building plans
and project deadlines.
Attention to detail, exceptional time management, and strong problem-solving and communication
skills are required for this role.
Decormart Studio is widely recognized as one of the best interior designers in Bangalore, known for their exceptional design expertise and ability to create stunning, functional spaces. With a strong focus on client preferences and timely project delivery, Decormart Studio has built a solid reputation for their innovative and personalized approach to interior design.
EASY TUTORIAL OF HOW TO USE CAPCUT BY: FEBLESS HERNANEFebless Hernane
CapCut is an easy-to-use video editing app perfect for beginners. To start, download and open CapCut on your phone. Tap "New Project" and select the videos or photos you want to edit. You can trim clips by dragging the edges, add text by tapping "Text," and include music by selecting "Audio." Enhance your video with filters and effects from the "Effects" menu. When you're happy with your video, tap the export button to save and share it. CapCut makes video editing simple and fun for everyone!
2. 800-856-4580
Power Generation Market
• Coal Pulverizer
• Boiler Penetration Seals
• Boiler Feedpump - Turbine
Exhaust
• HRSG Piping System
• Steam Turbine Crossover
Piping
• Steam Turbine to Condenser
Connection
• Extraction Steam Piping
• Turbine Steam Cooling
System
• Steam Distribution Heating
System
• Safety Relief Valve Vent
Piping
• Gas Turbine Exhaust
• Gas Turbine Rotor Air Cooling
• Gas Turbine Compressor
Bleed
• Micro Turbine Exhaust
3. Ship Building & Repair
800-856-4580
• Propulsion Exhaust System Piping
• Bulkhead Seals
• Auxiliary System Piping
• Cargo Vessel / Barge Product Transfer Piping
4. 800-856-4580
Chemical Processing
• Pumps
• Scrubber Piping
• Carbon Black
Processing
• Combustion Air
Preheater (CAPS)
• Caustic Media
Processing
• Resins Process Piping
• Product Transfer
Piping
5. 800-856-4580
Water / Waste Water
Water and Sewage
Applications for Metal
Expansion Joints:
• Pump Inlet
• Pump Outlet
• Blower Inlet
• Blower Outlet
• Condenser Inlet
• Condenser Outlet
• Steam Piping
• Water Piping
Metal Expansion Joints are found in Desalination Plants
6. 800-856-4580
Nuclear Technology
• Electrical shielding in
nuclear power plants
• Inlet to boiler feed pumps
• Outlet to boiler feed
pumps
• Low pressure concentrated steam
cascade piping