This document discusses using GPS receivers to dynamically monitor the vertical deflection of small concrete bridges. It presents preliminary results from monitoring the central span of a curved concrete bridge in Brazil using GPS data recorded at 100 Hz. The challenges are that small bridges only exhibit small peak-to-peak deflections of up to 5 mm. It used continuous wavelet transform analysis to analyze the frequency response of the bridge from GPS data in order to potentially provide a quick and effective monitoring method for the many small concrete bridges in Brazil.
Evaluation and Accuracy Assessment of Static GPS Technique in Monitoring of ...IJMER
It is well known that, deformation monitoring systems are considered, nowadays, to be the
back bone factor for human safety as well as preserving the ultimate economy of his achievements. In
this context, there has been always an increasing demand for precise deformation measurements in
keeping up several engineering structures and historical monuments. Measuring and monitoring
monumental deformation is the sequence of operations that allows the finding of movements of points
or features in a specified coordinate system, during two different times for the same investigated
feature. The time interval sometimes is the main factor in measuring horizontal deformation, especially
in loading test of steel bridges. Hence, the present paper investigates the accuracy of the GPS in
monitoring of horizontal deformation with respect to the time of observation. So, a practical
simulation test was made to assess the accuracy of GPS with time in measuring horizontal
deformation. The obtained results indicated that, the used methods and techniques presented in the
current research paper have possessed a very good accuracy, reliability and applicability in
monitoring horizontal deformations efficiently. The accuracy of measuring horizontal deformation of
points on structure using relative static technique of GPS is from (0.1mm) to (1.8mm) for time interval
from 30 minute to 5 minute and has R.M.S.E (0.3mm)
GPS cycle slips detection and repair through various signal combinationsIJMER
Abstract: GPS Cycle slips affect the measured spatial distance between the satellite and the receiver, thus affecting the accuracy of the derived 3D coordinates of any ground station. Therefore, cycle slips must be detected and repaired before performing any data processing. The objectives of this research are to detect the Cycle slips by using various types of GPS signal combinations with graphical and statistical tests techniques, and to repair cycle slips by using average and time difference geometry techniques. Results of detection process show that the graphical detection can be used as a primary detection
technique whereas the statistical approaches of detection are proved to be superior. On the other hand, results of repairing process show that any trial can be used for such process except for the 1st and 2nd time differences averaging all data as they give very low accuracy of the cycle slip fixation.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
Evaluation and Accuracy Assessment of Static GPS Technique in Monitoring of ...IJMER
It is well known that, deformation monitoring systems are considered, nowadays, to be the
back bone factor for human safety as well as preserving the ultimate economy of his achievements. In
this context, there has been always an increasing demand for precise deformation measurements in
keeping up several engineering structures and historical monuments. Measuring and monitoring
monumental deformation is the sequence of operations that allows the finding of movements of points
or features in a specified coordinate system, during two different times for the same investigated
feature. The time interval sometimes is the main factor in measuring horizontal deformation, especially
in loading test of steel bridges. Hence, the present paper investigates the accuracy of the GPS in
monitoring of horizontal deformation with respect to the time of observation. So, a practical
simulation test was made to assess the accuracy of GPS with time in measuring horizontal
deformation. The obtained results indicated that, the used methods and techniques presented in the
current research paper have possessed a very good accuracy, reliability and applicability in
monitoring horizontal deformations efficiently. The accuracy of measuring horizontal deformation of
points on structure using relative static technique of GPS is from (0.1mm) to (1.8mm) for time interval
from 30 minute to 5 minute and has R.M.S.E (0.3mm)
GPS cycle slips detection and repair through various signal combinationsIJMER
Abstract: GPS Cycle slips affect the measured spatial distance between the satellite and the receiver, thus affecting the accuracy of the derived 3D coordinates of any ground station. Therefore, cycle slips must be detected and repaired before performing any data processing. The objectives of this research are to detect the Cycle slips by using various types of GPS signal combinations with graphical and statistical tests techniques, and to repair cycle slips by using average and time difference geometry techniques. Results of detection process show that the graphical detection can be used as a primary detection
technique whereas the statistical approaches of detection are proved to be superior. On the other hand, results of repairing process show that any trial can be used for such process except for the 1st and 2nd time differences averaging all data as they give very low accuracy of the cycle slip fixation.
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
Assessment of the Usefulness of Egnos Differential Corrections in Conducting ...IJERA Editor
The article presents the results of research in determining the position of the base station in a static mode using
EGNOS differential corrections. The experiment was conducted in the Dęblin airport area. The experiment
comprised determining the coordinates of three base stations (REF1, VirA i VirB). The analysis of the results
for the tools adopted pointed out to the fact that the accuracy of coordinate determination for each station was in
the range of less than 2 meters.
Integrated Geophysical Approach for Rapid & Cost Effective Site Investigation...IEI GSC
Dr. Sanjay Rana, Director, PARSAN Overseas (P) Limited
With inputs & examples from Dr Gopal Dhawan & Dr S L Kapil
at 31st National Convention of Civil Engineers
organised by
Gujarat State Center, The Institution of Engineers (India) at Ahmedabad
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Functional Simulation of the Integrated Onboard System For a Commercial Launc...irjes
In the article has been chosen and simulated the integrated onboard guidance system of a
commercial launch vehicle with application of GPS technologies. In this study we shall consider a concept of
integrated onboard systems for launch vehicles in the context of the current task, and provide mathematical
models of all its elements for different variants of their structure and composition. Was set the conceptual design
of an integrated navigation system for the space launch vehicle qualified to inject small artificial Earth satellites
into low and medium circular orbits. The conceptual design of the integrated navigation system based on GPS
technology involves determination of its structure, models and algorithms, providing the required accuracy and
reliability in inject payloads with due regard to restrictions on weight and dimensions of the system
Terra is a listed company, which was founded in 2005, although the science that Terra uses goes back more than 35 years. Terra has over 500 years of Geotechnical, Exploration, Development, and Production combined experience.
Terra is represented in Indonesia by: PT. Indonesia – International Energy/Exploration Solution Partners which is a registered Indonesian owned company.
Terra is a powerful exploration solution that significantly improves the exploration success rate, reduces time from years to months, and when incorporated into a project, reduces wasteful spending on expensive seismic and drilling into non-prospective areas.
The Terra technologies address such challenges as:
* Large area high-grading and low-grading;
* Lack of subsurface data;
* Complex geology;
* Stratigraphic plays where seismic is not effective
* Lack, absence or poor quality of seismic data;
* Detection of subsurface structures, identifying high quality prospects which merit further exploration work and in many cases the presence of hydrocarbons and
minerals;
In General, the Terra technologies are superior tools for:
* Generating prospects in under-explored areas;
* Remotely or noninvasively delineate hydrocarbon and mineral anomalies and structures;
Dear Mercatorian,
By growing, Mercator resolutely turns towards users.
Such logical development, which comes also within the
wish of creation of the future operational centre, requires
more than ever to offer quality products which will well
reply to the downstream demand.
Correctly integrating observations in the assimilation
system and qualifying their impact stay one of the key
points to reach this objective.
The stake is double: to maintain/improve the operational
system performance, we need to consolidate the
present by demonstrating the importance of the ocean
data measurements: satellite, Argo floats, moorings and
others in situ measurement instruments, ... Furthermore,
it is necessary to prepare the future by testing new
assimilation methods, by estimating the future
observation systems relevance and by developing
strategy for their integration in the prototypes...
This Newsletter comes within this scope. The first article will describe the mean dynamic topography of the Mediterranean
Sea, as a reference required for altimetric data assimilation. Current and future topographies are described, assessed and
intercomparated in Mersea framework. The second article associates 4D-variational method and Argo drifting floats to
examine the potential we may expect of vertical profiles of temperature and salinity to produce the oceanic state. Finally, the
last article describes the Mercator strategy, developped in the scope of an ESA study, for the future surface salinity
observation system: SMOS.
Among all of this, don't forget Europe, par excellence topically question at these days and which is approached in the News
through the first annual Mersea meeting, held in Toulouse from March 29 to March 31st.
Have a good read and see you for next issue with regional and coastal oceanography topic!
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
Assessment of the Usefulness of Egnos Differential Corrections in Conducting ...IJERA Editor
The article presents the results of research in determining the position of the base station in a static mode using
EGNOS differential corrections. The experiment was conducted in the Dęblin airport area. The experiment
comprised determining the coordinates of three base stations (REF1, VirA i VirB). The analysis of the results
for the tools adopted pointed out to the fact that the accuracy of coordinate determination for each station was in
the range of less than 2 meters.
Integrated Geophysical Approach for Rapid & Cost Effective Site Investigation...IEI GSC
Dr. Sanjay Rana, Director, PARSAN Overseas (P) Limited
With inputs & examples from Dr Gopal Dhawan & Dr S L Kapil
at 31st National Convention of Civil Engineers
organised by
Gujarat State Center, The Institution of Engineers (India) at Ahmedabad
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Functional Simulation of the Integrated Onboard System For a Commercial Launc...irjes
In the article has been chosen and simulated the integrated onboard guidance system of a
commercial launch vehicle with application of GPS technologies. In this study we shall consider a concept of
integrated onboard systems for launch vehicles in the context of the current task, and provide mathematical
models of all its elements for different variants of their structure and composition. Was set the conceptual design
of an integrated navigation system for the space launch vehicle qualified to inject small artificial Earth satellites
into low and medium circular orbits. The conceptual design of the integrated navigation system based on GPS
technology involves determination of its structure, models and algorithms, providing the required accuracy and
reliability in inject payloads with due regard to restrictions on weight and dimensions of the system
Terra is a listed company, which was founded in 2005, although the science that Terra uses goes back more than 35 years. Terra has over 500 years of Geotechnical, Exploration, Development, and Production combined experience.
Terra is represented in Indonesia by: PT. Indonesia – International Energy/Exploration Solution Partners which is a registered Indonesian owned company.
Terra is a powerful exploration solution that significantly improves the exploration success rate, reduces time from years to months, and when incorporated into a project, reduces wasteful spending on expensive seismic and drilling into non-prospective areas.
The Terra technologies address such challenges as:
* Large area high-grading and low-grading;
* Lack of subsurface data;
* Complex geology;
* Stratigraphic plays where seismic is not effective
* Lack, absence or poor quality of seismic data;
* Detection of subsurface structures, identifying high quality prospects which merit further exploration work and in many cases the presence of hydrocarbons and
minerals;
In General, the Terra technologies are superior tools for:
* Generating prospects in under-explored areas;
* Remotely or noninvasively delineate hydrocarbon and mineral anomalies and structures;
Dear Mercatorian,
By growing, Mercator resolutely turns towards users.
Such logical development, which comes also within the
wish of creation of the future operational centre, requires
more than ever to offer quality products which will well
reply to the downstream demand.
Correctly integrating observations in the assimilation
system and qualifying their impact stay one of the key
points to reach this objective.
The stake is double: to maintain/improve the operational
system performance, we need to consolidate the
present by demonstrating the importance of the ocean
data measurements: satellite, Argo floats, moorings and
others in situ measurement instruments, ... Furthermore,
it is necessary to prepare the future by testing new
assimilation methods, by estimating the future
observation systems relevance and by developing
strategy for their integration in the prototypes...
This Newsletter comes within this scope. The first article will describe the mean dynamic topography of the Mediterranean
Sea, as a reference required for altimetric data assimilation. Current and future topographies are described, assessed and
intercomparated in Mersea framework. The second article associates 4D-variational method and Argo drifting floats to
examine the potential we may expect of vertical profiles of temperature and salinity to produce the oceanic state. Finally, the
last article describes the Mercator strategy, developped in the scope of an ESA study, for the future surface salinity
observation system: SMOS.
Among all of this, don't forget Europe, par excellence topically question at these days and which is approached in the News
through the first annual Mersea meeting, held in Toulouse from March 29 to March 31st.
Have a good read and see you for next issue with regional and coastal oceanography topic!
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will be used in future automotive navigation systems. This system will be a composite of the United States' Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System (GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A further study of this patch antenna illustrates the absolute phase center variation measured in an indoor range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is investigated when integrated into a standard multi-band automotive antenna product. This product is evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using this evaluation file to estimate the receiver position could achieve phase motion error-free result.
DUAL BAND GNSS ANTENNA PHASE CENTER CHARACTERIZATION FOR AUTOMOTIVE APPLICATIONSjantjournal
High-accuracy Global Navigation Satellite System (GNSS) positioning is a prospective technology that will
be used in future automotive navigation systems. This system will be a composite of the United States'
Global Positioning System (GPS), the Russian Federation's Global Orbiting Navigation Satellite System
(GLONASS), China Beidou Navigation Satellite System (BDS) and the European Union’s Galileo. The
major improvement in accuracy and precision is based on (1) multiband signal transmitting, (2) carrier
phase correction, (3) Real Time Kinematic (RTK). Due to the size and high-cost of today’s survey-grade
antenna solutions, this kind of technology is difficult to use widely in the automotive sector. In this paper, a
low-cost small size dual-band ceramic GNSS patch antenna is presented from design to real sample. A
further study of this patch antenna illustrates the absolute phase center variation measured in an indoor
range to achieve a received signal phase error correction. In addition, this low-cost antenna solution is
investigated when integrated into a standard multi-band automotive antenna product. This product is
evaluated both on its own in an indoor range and on a typical vehicle roof at an outdoor range. By using
this evaluation file to estimate the receiver position could achieve phase motion error-free result.
Case studies of surveys involved in Railway Tunnel constructed under sea.Prudhvi Thota
Case Studies of detailed explanation of Hydro graphic survey, R.T.K. GPS, Seismic designing, profile survey etc involved in the construction and Designing aspects of Mammary Railway Tunnel under the sea.
A Fully Automated System for Monitoring Pit Wall DisplacementsJOSE ESPEJO VASQUEZ
ABSTRACTO.
El Monitoreo automatizado de taludes empinados, excavaciones y terraplenes altos; permite la detección temprana de la inestabilidad y se puede utilizar para evitar o mitigar las posibles fallas de taludes.
Los sistemas que utilizan múltiples y diferentes tipos de sensores se han desarrollado y probado con éxito en la Mina Highland Valley Copper en la Columbia Británica. Estos sistemas utilizan estaciones totales robóticas (RTS) como principales sensores de medición, con levantamientos repetidas en intervalos predefinidos seleccionados para optimizar la eficiencia operativa.
Esta metodología ha sido desarrollada para mejorar el sistema de exactitud y fiabilidad mediante la reducción de los efectos de errores sistemáticos creados por la refracción atmosférica e instrumento inestable y posiciones de punto de referencia. La inclusión de sensores GPS para monitorear las posiciones RTS crea flexibilidad operativa adicional y mantiene la integridad del sistema cuando las estaciones de referencia disponibles son insuficientes.
Reliability analysis of pmu using hidden markov modelamaresh1234
As modern electric power systems are transforming into smart grids, real time wide area monitoring system (WAMS) has become an essential tool for operation and control. With the increasing applications of WAMS for on-line stability analysis and control in smart grids, phasor measurement unit (PMU) is becoming a key element in wide area measurement system and the consequence of the failure of PMU is very severe and may cause a black out. Therefore reliable operation of PMU is very much essential for smooth functioning of the power system. This thesis is focused mainly on evaluating the reliability of PMU using hidden Markov model. Firstly, the probability of given observation sequence is obtained for the individual modules and PMU as a whole using forward and backward algorithm. Secondly, the optimal state sequence each module passes through is found. Thirdly, the parameters of the hidden Markov model are re-estimated using Baum-Welch algorithm.
Displacement mechanical amplifiers designed on poly-siliconIJECEIAES
Using Poly-Silicon, the implementation of novel Displacement-amplifying Compliant Mechanisms (DaCM), in two geometries of accelerometers, allows for remarkable improvements in their operation frequency and displacement sensitivity, with different proportions. Similar DaCM´s geometries were previously implemented by us with Silicon. In all mentioned cases, the geometries of DaCM´s are adjusted in order to use them with Conventional Capacitive Accelerometer (CCA) and Capacitive Accelerometer with Extended Beams (CAEB), which operate in-plane mode, (y-axis). It should be noted that CAEB shows improvements (95.33%) in displacement sensitivity compared to ACC. Simulations results, carried out using Ansys Workbench software, validate the system’s performance designed with Poly-Silicon. Finally, a comparison with the similar systems, previously designed with Silicon, is also carried out.
Development of Methodology for Determining Earth Work Volume Using Combined S...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
International Journal of Modern Engineering Research (IJMER) covers all the fields of engineering and science: Electrical Engineering, Mechanical Engineering, Civil Engineering, Chemical Engineering, Computer Engineering, Agricultural Engineering, Aerospace Engineering, Thermodynamics, Structural Engineering, Control Engineering, Robotics, Mechatronics, Fluid Mechanics, Nanotechnology, Simulators, Web-based Learning, Remote Laboratories, Engineering Design Methods, Education Research, Students' Satisfaction and Motivation, Global Projects, and Assessment…. And many more.
Channel Overlapping Between IMT-Advanced Users and Fixed Satellite ServiceEECJOURNAL
The Novel technique to modulate the nulls in the radiation pattern of IMT-Advanced base station (BS) towards the fixed satellite service is (FSS) affirmed in this paper. Designing a new algorithm to extract the nulls in the forbidding area and other base on MUSIC algorithm to estimate the direction of mobile user and control the handover technique is our major concern. A scenario of two mobile users (MS) moving around one FSS had been exclusively studied and simulated. Calculating the shortest separation distance after identifying the critical point and compare the result with the recent recommendation had shown how magnificent coexistence and spectrum sharing we can get.
Transcript: Selling digital books in 2024: Insights from industry leaders - T...BookNet Canada
The publishing industry has been selling digital audiobooks and ebooks for over a decade and has found its groove. What’s changed? What has stayed the same? Where do we go from here? Join a group of leading sales peers from across the industry for a conversation about the lessons learned since the popularization of digital books, best practices, digital book supply chain management, and more.
Link to video recording: https://bnctechforum.ca/sessions/selling-digital-books-in-2024-insights-from-industry-leaders/
Presented by BookNet Canada on May 28, 2024, with support from the Department of Canadian Heritage.
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Dev Dives: Train smarter, not harder – active learning and UiPath LLMs for do...UiPathCommunity
💥 Speed, accuracy, and scaling – discover the superpowers of GenAI in action with UiPath Document Understanding and Communications Mining™:
See how to accelerate model training and optimize model performance with active learning
Learn about the latest enhancements to out-of-the-box document processing – with little to no training required
Get an exclusive demo of the new family of UiPath LLMs – GenAI models specialized for processing different types of documents and messages
This is a hands-on session specifically designed for automation developers and AI enthusiasts seeking to enhance their knowledge in leveraging the latest intelligent document processing capabilities offered by UiPath.
Speakers:
👨🏫 Andras Palfi, Senior Product Manager, UiPath
👩🏫 Lenka Dulovicova, Product Program Manager, UiPath
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
"Impact of front-end architecture on development cost", Viktor TurskyiFwdays
I have heard many times that architecture is not important for the front-end. Also, many times I have seen how developers implement features on the front-end just following the standard rules for a framework and think that this is enough to successfully launch the project, and then the project fails. How to prevent this and what approach to choose? I have launched dozens of complex projects and during the talk we will analyze which approaches have worked for me and which have not.
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
Search and Society: Reimagining Information Access for Radical FuturesBhaskar Mitra
The field of Information retrieval (IR) is currently undergoing a transformative shift, at least partly due to the emerging applications of generative AI to information access. In this talk, we will deliberate on the sociotechnical implications of generative AI for information access. We will argue that there is both a critical necessity and an exciting opportunity for the IR community to re-center our research agendas on societal needs while dismantling the artificial separation between the work on fairness, accountability, transparency, and ethics in IR and the rest of IR research. Instead of adopting a reactionary strategy of trying to mitigate potential social harms from emerging technologies, the community should aim to proactively set the research agenda for the kinds of systems we should build inspired by diverse explicitly stated sociotechnical imaginaries. The sociotechnical imaginaries that underpin the design and development of information access technologies needs to be explicitly articulated, and we need to develop theories of change in context of these diverse perspectives. Our guiding future imaginaries must be informed by other academic fields, such as democratic theory and critical theory, and should be co-developed with social science scholars, legal scholars, civil rights and social justice activists, and artists, among others.
PHP Frameworks: I want to break free (IPC Berlin 2024)Ralf Eggert
In this presentation, we examine the challenges and limitations of relying too heavily on PHP frameworks in web development. We discuss the history of PHP and its frameworks to understand how this dependence has evolved. The focus will be on providing concrete tips and strategies to reduce reliance on these frameworks, based on real-world examples and practical considerations. The goal is to equip developers with the skills and knowledge to create more flexible and future-proof web applications. We'll explore the importance of maintaining autonomy in a rapidly changing tech landscape and how to make informed decisions in PHP development.
This talk is aimed at encouraging a more independent approach to using PHP frameworks, moving towards a more flexible and future-proof approach to PHP development.
PHP Frameworks: I want to break free (IPC Berlin 2024)
B04920920
1. IOSR Journal of Engineering (IOSRJEN) www.iosrjen.org
ISSN (e): 2250-3021, ISSN (p): 2278-8719
Vol. 04, Issue 09 (September. 2014), ||V2|| PP 09-20
International organization of Scientific Research 9 | P a g e
Dynamic Monitoring vertical Deflectionof Small Concrete Bridge Using Conventional Sensors And 100 Hz GPS Receivers - Preliminary Results ANA PAULA CAMARGO LAROCCA 1 JOÃO OLYMPIO DE ARAÚJO NETO 2 AUGUSTO CÉSAR BARROS BARBOSA 3 JORGE LUIZ ALVES TRABANCO 4 ANDRÉ LUIZ BARBOSA NUNES DA CUNHA 1 1 São Paulo University, São Carlos School of Engineering (USP-EESC) – São Carlos, SP, Brazil 2 Federal Institute of Education, Science and Technology (IFSULDEMINAS) – Inconfidentes, MG, Brazil 3 State University of Ceará, Science and Technology Center (UECE-CCT) – Fortaleza, CE, Brazil 4 Campinas State University, Civil Engineering School (UNICAMP) – Campinas, SP, Brazil Abstract: - The last four decades have been significant for Brazil‟s highway network development. The country received financial incentives for its expansion and created various structural solutions for bridges and overpasses. Concurrent to this development, in recent years these structures have increasingly shown advanced deterioration stages due to the lack of preventive maintenance programs. Thus, this paper proposes the use of a GPS in a short-term monitoring plan to oversee the structural behavior of a curved reinforced concrete highway bridge already in service. Accordingly, this article presentsthe first research results with the L1 carrier and recorded data at 100 Hz in order to monitor the dynamic behavior of the central span of a small curved concrete bridge, the bridge over the Jaguari River in Extrema, Minas Gerais. The problem is that such structures exhibitsmall peak-to-peak amplitude vertical deflections– up to 5 mm.The challenge lies in the fact that the vast majority of Brazil‟s highway network is characterized by small and medium sized concrete bridges. The bridge monitored in the study consists of two traffic lanes and a total length of 134 m, located in the Fernão Dias highway– BR 381, km 946 + 300m, Extrema, Minas Gerais. The bridge under study is significant to this work because this type of structure is largely found throughout the country. Thus, the line of work to be presented will contribute to implementing other monitoring actions forthese types of structures throughout Brazil – quickly and effectively,which will serve as a strategythat can beadded to the conventional monitoring methods. Therefore, GPS data observations were conductedfor two days using two GPS receivers with data sampling intervals of 0.01 seconds- 100 Hz. The Continuous Wavelet Transform (CWT) was used as filtering model to analyze the frequency response of the bridge generated by the residues of the L1 double difference through the highest GPS satellite constellation. Keywords: - Small Concrete Bridge; GPS;Dynamic Monitoring.
I. INTRODUCTION
In recent years Brazil has witnessed a significant increase of early deterioration in the special works caused by the lack of preventive maintenance programs for such structures. Albeit Brazil‟s regulatory bodies provide the complete procedure for inspecting and ensuring the integrity of OAEs, in most cases the pathologies are detected and measures are taken only when the structural deterioration reaches a critical state or when it poses risksto the users. A study conducted by SINAENCO (National Association of Architectural and Consulting Engineering Companies), entitled “Infrastructure of the City: Expiration of theValidity Period” shows the need for a permanent structural conservation and resource managementpolicy. Regarding the special structural works in the city of São Paulo, the study shows that there are 240 bridges and overpasses in state of deteriorationexhibiting various pathologies and posing risks to the users. One of the main factors highlighted for the deterioration regardsinsignificantconservation investments in recent years, corresponding to 0.38% of the final construction cost [18], [1]. This paper presents the partial results of the dynamic monitoring of fluctuations of one of theroadway spans of a small concrete bridge, which used Global Positioning System (GPS). The tests presented below are part of the continuity development of a method, initiated in 2000, in order to improve the GPS detection threshold so that it can also be used in the dynamic monitoring of small rigid-frame bridges. From the beginning of this work, the Phase Residual Method (PRM) was implemented in the monitoring of medium and large sized suspension and cable bridges [10], [11], [12],[17].
As the Brazilian highway network is almost entirely composed ofsmall and midsized concrete bridges it was necessary to continue the development of the method.The goal is that the ease and speed of using the GPS, as a
2. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 10 | P a g e
tool for monitoring dynamic oscillations of small and medium sized concrete bridges, can be widely used by engineering, also in Brazil. ThePhase Residual Method, which in its processing uses theL1 carrier-phase data transmitted by only two satellites to the GPS receivers – the mobile one installed at the bridge, and the fixed one installed at the correction station outside the structure. The method includes the use of an electromechanical oscillator with known amplitude and specifically designed to install the GPS antenna, which enables calibrating the degree and frequency of oscillation in the structure. The following results are from initial field tests, carried outon a small reinforced concrete bridge, located at theFernão Dias Highway, in the city ofExtrema, southern Minas Gerais [2].
II. THEORETICAL BASIS OF THE METHOD USED
The method applied in this paper uses data from the GPS positioning system, transmitted by the L1 carrier phase, based on Michelson‟s interferometer principle, already published in previous works[10], [11], [12],[17].In essence, this methodology consists in the application of the principle of interference on the signals transmitted by the satellites of the GPS constellation to measuredistances by the phase changecaused on one of the signals. In this case, a mobile receiver is installed on the structure to be monitored and the other receiver (fixed or base), responsible for the differential corrections, is installed on a base with known coordinates. Figure 01 illustrates a GPS antenna fixed on the central span of a suspension bridge, excited by dynamic load – in this case, the crossing of a truck. The frequency and oscillation amplitude of the central span are determined from the analysis of the GPS signals collected. Figure 1 – GPS antenna of the mobile receiver over the bridge [2]
The method used, based on the principle of the interferometer phase, only requires the data collection from two satellites, with phase close to 90° and no more than one constellation with four satellites. Thus, to measure a vertical displacement for example, a satellite should have an altitude of approximately 90° and the other with an altitude close to the horizon (Figure 02). In the processing of dual phase difference, the lower satellite is considered as the reference satellite, which allows obtaining the vector of the residues from the highest satellite, here termed as„measuringsatellite‟. Figure 2 –Configuration of the reference Satellite and measuring Satellite [2].
1.1 Electro-Mechanical Oscillator
An electromechanical oscillator (Electromechanical Oscillator – EMO) was developed to calibrate the measurement of previously unknown dynamic displacements, which applies controlled movements, related to
3. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 11 | P a g e
amplitude and speed of the structure in the GPS antenna which sustains the movements of the structure. The oscillator is powered by a 9V battery that helps maintain a constant oscillation in the frequency range measured. Figure 3 shows the JAVAD GPSantenna positionedon the oscillator, which is installed on a geodetic pillar of IBGE, during the coordinated transport to the nearby region of the bridge in question. Figure 3 –Detail of the Electromechanical Oscillator with theJAVAD antenna and oscillator
1.2 Spectral Data Analysis
For the spectral analysis of residues from the GPS processing of the dual-difference phase, we used the Continuous Wavelet Transform – CWT), using the Morlet mother wavelet [15]. CWT allows analyzing spectral variations with different time-frequency-space resolutions. This method is also recommended for specific applications such as noise removing methods, since it uses mathematical reasoning in the classical methods developed byJoseph Fourier (The well knownFourierTransform).This means that a signal can be mapped in a time-scale plane through a scalegram[7],[16], [18]. CWT has a setof “linear” operations (convolution), which can be used in non-stationary signal studies for extracting frequency variation information and to detect oscillations of the structures located in the time scale with its spatial location. This method has been widely used in various fields of research and applications, such asin geophysical, hydrology, climate data and medical analysis, in sound studies, GPS data analysis, andin other areas, see[4]. The decision to use the CWT with the Morlet mother wavelet was strategic, since the analyzed signals are not represented simultaneously in time and frequency by the classical Fourier transform, as they are non-stationary, and also because of theenergy difference.Additionally, these signals have small peak-to-peak amplitude (up to 5 mm) in a low frequency region, detectable structure by using continuous Wavelet Transforms. To this end, and as mentioned earlier, the Morlet mother wavelet was used, defined as follows [15] 훹표 휂 = 휋−1/4푒푖푤표휂푒−1/2휂2 (1) Where: wois the dimensionless cutoff frequency (equal to 6.0, seeTorrence & Compo, 1998); and ηis the dimensionless time. When this type of filter is used for extracting features from a time series, theMorlet wavelet is a good choice, since it provides excellent balance between time and frequency localization. The CWT conceptregards theband- pass filter applied to the time series. The CWT of a time series (f(t), t = 1, ... , N) with time intervals uniformly distributed by dt is defined as the convolution f(t)with the Morletmother wavelet, scaled and normalized: Wj,k t = 1 j f t Ψo t−kj Nt=1dt (2) WhereWj,k (t)is the similarity between the mother wavelet function and the time series 푓(t), in other words, the higher the value of Wj,k (t), the higher the similarity between the function analyzed and the Morlet wavelet function, which modulates the signal analyzed. For a function to be considered a Mother Wavelet function(WF), represented by 훹0, the following key properties must be satisfied: 1st Property: The integral of the function must be zero, Ψ0 t dt=0+∞ −∞ (3)
4. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 12 | P a g e
Equation (3) ensures that the WF assumes a wavelike shape. This condition is known as an“admissibility” condition. This ensures the existence of the “Inverse Wavelet Transform”, in the composition of the original series. 2nd Property: Must haveenergy unit, i.e., Ψ0(t) 2=1+∞ −∞ (4) Equation (4) ensures that the WF has compact support, that is, a rapid e-folding time, which ensures that the motherwavelet presents spatial location, a large differential relative to Classical Fourier Transform.
III. CONCRETE BRIDGE OVER THE JAGUARIRIVER, MINAS GERAIS
The concrete bridge over the Jaguari River (Figure 4) was chosen for the experiments because it is a small concrete overpass. Figure 4 –Bridge under study over theJaguari River.
The bridge is situated over the Jaguari River at a stretch of the Fernão Dias highway - BR 381, km 947, of the southbound access of Extrema in southern Minas Gerais, near the border with the state of São Paulo (Figure 5). Figure 5 – An overview of the Fernão Dias Highway in Brazil.
The study focused only on the southern bridge due to its higher vibration and higher vertical displacement on account of the local traffic load. The structural behavior has been consistently observed using structural and geotechnical methods by the research team coordinated by Professor Túlio Nogueira Bittencourt, from theLaboratory of Structures and Structural Materials of theDepartment of Structures and Foundations at the Polytechnic School of the University of São Paulo. The structure of the south bridge is divided into five symmetrical spans of: 20m, 26m, 30m, 26m and 20m, with the superstructure supported by 6 pairs of pillars. It is continuous and has no expansion joints, which shows at the ends an abutment with the reinforced concrete transition slab, continuing on the road. Its longitudinal axis has aslope of 5.9% (southward), and continuous roadway superelevation of 8% and projection curvature radius of 305.50 m. Due to the superelevation there is a discrepancy between the pairs of pillars of approximately 50 cm. The total width of the roadway is 11.70 m, of which 10.90 m is divided by the two traffic lanes and a shoulder lane, plus 0.40m for each New-Jersey barriersmade of reinforced concrete. The cross section is the π spaced at6.40 m between the stringers (center to center); of 40 cm in width and a total height of 2.80 m [1]
5. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 13 | P a g e
1.3 Numerical Modeling and Load Test
The numerical modeling of the bridge over the Jaguari River was based on the Finite Element Method. Five elastic-linear models were studied and created and one non-linear model using the SAP2000® V14 and Midas Fx+ for DIANA® softwares [1] The dynamic analysis was performed in order to obtain parameters that canevaluate the structural behavior under free vibration. The spectral content analyzed enabled to verify themost excited frequencies, which may correspond to the first symmetric bending frequencies in the longitudinal vertical plane of the bridge. These frequencies are in the range of 5 Hz to 10 Hz. Figure 6 shows the identification and location of the sensors and transducers used in the monitoring campaign carried out in 2011. The S1 session data were compared with the GPS collected data for exhibiting the largest vertical displacement of 3.55 mm [1] Figure 6 –Instrumentation layout of the 30 m bridge span over the Jaguari river [1].
Table 1 shows the expected vertical displacement for the LB stringer from the linear analysis results. Table1 –Linear Analysis: Comparative vertical displacement of LV Stringer, 30 m span (Andrade et al., 2013).
Modulus ofElasticity (GPa)
Displacement (mm)
Relative error (%)
Numeric Model (NM)
Test Vehicle (TV)
24.68
2.933
3.55
17.37
23.80
3.047
14.16
The monitoring stage with controlled traffic was conducted on October 19, 2011. To perform this stage, the traffic was completely stopped, only allowing the passage of the test vehicle. The test vehicle consisted of a five-axle truck, 2 axles on the mechanical horse and 3 axles on the semi-trailer, as shown in Figure7. The total weight of the loaded and unloaded test vehicle was 44.3 t and 16.7 t, respectively [1] Figure 7 –The test load vehicle used in the test over the bridge [1].
Figure 8 illustrates the acceleration and frequency in the vertical direction for monitoring the normal traffic, on October 10, 2011.
6. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 14 | P a g e
Figure 8 –Acceleration spectrum (frequency) in the vertical direction for monitoring normal traffic on 10/10/2011 [1].
IV. DATA COLLECTION WITH 100HZ GPS RECEIVER
Analyses to test the GPS as a tool for monitoring the central span of the concrete bridge was conducted in three stages: the first stage consisted of the coordinated transportation to the region close to the bridge; the second one used only the EMO with controlled amplitude and frequency, on a geodetic framework for tests to detect vertical deflections of up to 5 mm. In the third and most complete stage, observations were made on the reinforced concrete bridge inExtrema, Minas Gerais. All data collection stages used two GPS receivers (JAVAD, SIGMA model), with data logging of 100 Hz and chokering antennas (RegAnt_DD JAVADmodel).
1.4 Coordinate Transportation for the Region Nearest to the Bridge
The procedure to characterize the behavior of the bridge with the GPS receiver was done by static relative positioning, thus a geodetic mark with adjusted coordinates was used. There was no geodetic framework in the vicinity of the bridge that could be used for post-processing the observations. This situation then required building a geodetic mark (Figure 9a) near the bridge which would meet the standards and quality standards suggested by the IBGE [2] Figure 9 – (a) Construction coordinated by the author who is from IFSULDEMINAS (b) The construction project elaborated by IBGE
The construction site of the geodesic landmark was the center of a roundabout of kilometer 947 south, of the Fernão Dias highway, 300 m from the bridge under observation. Figure 9 illustrates the design situation of thenew framework implemented, the roundabout next to the bridge, the bridge and the base point for the coordinate transport, situated in IFSULDEMINAS - Inconfidentes Campus. Thus, a cylindrical concrete pillar was built (30 cm diameter and 1.20 m in height). The framework basehas a rectangular shape of 1.40 mx 50 cm across and 60 cm in depth. The structure comprisediron stakes (3/8 inch iron) with the same length of thedrilled holes, and withbinding points inserted in the holes. A radier of 1.30 m 40 cm was also placed (Figure 9b). After the construction of the frame, the GPS datacollection was performed(Figure 10)for the coordinatedtransport. This procedure was performed on 3 different days, with 6 tracking hours for its approval by the qualified institution. The engineers of IBGE‟sGeodesy Department performed the proper processing and adjustments of the coordinates with the Bernese scientific software version 5.0, and its approval, including it in the Brazilian geodetic network in June 2013.
7. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 15 | P a g e
Figure 10 –Data collection in the GeodeticPillar for its approval by IBGE
1.5 EMO Simulations
The first test used the OEM device (motion simulator) and the JAVAD SIGMA receiver installed on it, which was placed on the geodesic mark located atFederal Sul Institute of Minas Gerais - Inconfidentes Campus, Minas Gerais, Brazil, according toFigure 11. TheOEMwas used to apply a controlled vertical movement to the GPS antenna with a frequency and amplitude of 0.4 Hz and 3.8 mm, respectively.To record the GPS constellation observations, theJAVAD SIGMAreceivers were used with a recording rate of 100 Hz, for 3 minutes.The result of this test was decisive for the test in the actual structure, in this case, the concrete bridge over the Jaguari River. Figure 11 – GPS antenna operating on the Electromechanical Oscillator andPillar of IBGE in IFSULDEMINAS – Inconfidentes Campus.
1.6 EMO simulation results
Figure 12 (below) shows the Energy Spectrumof the residues from the GPS processing of the phase double difference, obtained with the Morlet mother wavelet. The mathematical model used to generate the spectrum was set to show phenomena with 5% statistical significance, that is, 95% ofconfidence –whose significance level is limited by the contour represented by a black line inside the Cone of Influence (COI, [3], [4]). The information from the frequency spectra,based on the residues due to the motion assigned to EMO, will be used as reference for the other analyses presented in this paper. The axis of abscissa (X-axis) is the number of observations (every 0.01 s), the y-axis on the left is the frequency value in Hertz and the y-axis on the right is the energy intensity scale with which the frequency is displayed in the Cone of Influence area. Also, in this figure, the upper graph refers to the gross residues without any treatment or filter, only normalized byN-1, where N is the number of observations derived from the L1 double difference carrier phase, due to the periodic motion of the EMO. The other energy graphics generated by the mathematical model in Mathlab language follow the same description pattern.
8. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 16 | P a g e
Also inFigure 12,there is a highly significant continuous energy band, detected and represented in red over the entire time series period,which corresponds to the oscillations programmed and applied by EMO in the mobile antenna at approximately 0.4 Hz.Between the 3000 and 4000 observations (Note1), energy records of around 2 Hz are observed –which need to be further investigated with field traffic observations. Figure 12 – Energy Spectrum (bottom, left) of the residues of the time series for the3000-6000observations, with a significance level of 5% limited by theCOI.
V. GPS DATA COLLECTION ON THE CONCRETE BRIDGE OVER THE JAGUARI RIVER
The first tests on the bridge were carried out at different times from the conventional load tests thusfar been conducted by the researchers from the group of Professor Túlio Nogueira Bittencourt. This was due to the need for a coordinated transportation –construction of the pillar at the roundabout – installation of the pins to fix the GPS antenna on the guardrail of the bridge and tests to confirm the detection threshold of the method. New tests are planned to be conducted simultaneously with the load test, the instrumentation with accelerometer and GPS receivers.
1.7 Instrumentation Layout
The instrumentation and GPS data collection took place with the bridge under local highway traffic.During the data collection period, the bridge was under constant traffic by the different categories of heavy vehicles transiting the highway in question. Figures 13a, 13b and 13c show a more detailed lower view of the structure and over the monitored bridge, with the mobile GPS antenna installed on the guardrail,using epoxy to fixthe pin. Figure 13 – (a) bottom view of the bridge, (b) view of the bridge during the tracking with the GPS receiver, (c) detail of pin fixed with epoxy.
Figure 14 illustrates the location of the mobile GPS receiver (rover) on the center of the largest central span of the bridge. The electromechanical oscillator was adjusted to apply a vertical offset of 3.8 mm and frequency of 0.40 Hz. There were two-measurement phaseon the bridge, one using EMO and the other one without the device. Figure 13 –Sketch of the bridge with the GPS receiver positioned on the30m span.
9. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 17 | P a g e
1.8 GPS Data Collection
At this monitoring stage the GPS antenna was installed on the Jaguari Bridgethrough a forced centering universal threaded pin fixed to the middle and edge of the bridge, as shown in Figure 13b. The GPS base was installed on another geodesic landmark built for this purpose (Figures 09 and 10), 300 m from the bridge under test. The data collection rate of the receptors was 100 observations per second. The Justin JAVAD v. 2.107software was used to process the data collected over the bridge. According to the methodology, satellite 11 was used as satellite reference because it was on the horizonwith11oof altitude, and satellite 14 was chosen as “measuring”satellitebecause it is located closer to the zenith, with 87º of altitude,illustrated in the SKYPLOT ofFigure 14. Figure 14 – SKYPLOT of GPS Constellation in the Bridge Experiment on 17/06/2013
1.9 Analysis of Results
Figure 15 shows the first 20 seconds of data collected with a series of 2000observations, with intervals of 0.01 s. The first graph illustrates the residues of double phase difference between satellites 11 and 14. A high energy level is observed due to the multipath of the GPS signal over the frequency range close to the 0.05 Hz value [9] – value for the GPS JAVAD SIGMA receivers with multipath attenuation.Additionally, high energy values with 4 to 8 Hz frequency were observed, corresponding to the frequency band detected during the load test, with the accelerometer installed in the stringer of the 30 m span, under the action of normal traffic.Thus, at this research stage the vertical movements of 30 m span with displacement amplitude of 3.55 mm were identified.
10. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 18 | P a g e
Figure 15 –CWT of the residues of the time series of 0-2000observations, with a significance level of 5% limited by the COI.
Highenergy level was also observed in the region with the 600 and 1800periods. At this stage it is assumed that it may be the response of this span to the passage of larger vehicles such as road trains.In the next research stage there is the comparison of the GPS data recorded period-to-period for thefilmed vehicles that passed through the bridge or the data of the motion weighing sensor that is being installed at the nearby toll plaza. Figure 16 shows the data collected in the following 20 seconds (ofFigure 15). Within the cone of influence, three regions areagain observed,determined by A, B and C, with a high level of energy due to the passage of heavier vehicles such as single or road trains, as mentioned above and to be elucidated.On the other hand, the frequencies in the 4 to 8 Hz range are identified, coinciding with the numerical model and with the load test values performed in 2011.A priori, these frequencies show the possibility of energy transfer between scales, in other words, between the natural vibration of the bridge, with the frequency generated by the passage of vehicles. However, a control experiment isviable for this assertion. Figure 16 –CWT of the residues of the time series of 2000-4000 observations, with a significance level of 5% limited by the COI.
VI. CONCLUDING REMARKS
The initial results from the method application that combines Global Positioning System (GPS), Phase Residue Method (PRM) and CWT as a civil engineering tool to monitor the vibrations of small structures allowed to detect vertical deflection frequencies with peak-to-peak amplitude of 3.55 mm, with a high confidence level (95%). The next steps consist ofthe testsconducted on the same bridge, with joint GPS technology and accelerometers. The initial tests performed at IFSULDEMINAS were essential for planning the other monitoring projects – as the results achieved were consistent with the expected quality for a reference. The CWT images of the preliminary tests show that the resonance frequency stability of the wave signal justifies the quality of the combination and methodology used. The data were filtered and presented at high energy concentration frequency in most of the time series, around 0.4 Hz, exactly in the order in which the oscillation frequency was set.
11. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 19 | P a g e
The results of the Jaguari Bridge also served to broaden the investigation from the perspective of defining the spectral behavior that each type of road vehicle causes on the bridge. Thus, from the GPS data analysis and the CWT results, it is possible to provide a response spectrumof the span for each type of vehicle. According to the library, only GPS data needs to be collected,without having to interrupt traffic on concrete bridges with similar structural configurations. Based on these results, it is concluded that the proposed combination of usinghigh-data rate (100 Hz) GPS receivers with CWT filtering techniques allows to detect, with confidence level of 95%, the senoidal waves from the vertical deflections of the 30 m span length concrete highway bridge. The next research stagesintend toperform traffic analysis and create a response library of the 30 m span for the several types of vehicles crossing, by wavelet analysis, and detail the road movement during the crossing of vehicles.
VII. ACKNOWLEDGMENTS
The authors are grateful to FEC –School of Civil Engineering of UNICAMP; to IFSULDEMINAS, Inconfidente Campus,for the support and encouragement to the second author; to the team of researchers coordinated by Professor Dr. Túlio Nogueira Bittencourt, of theDepartment of Structural and Foundation Engineering –Polytechnic School of USP, especially to the engineers Alberto B.Colombo, Leila Meneghetti Vaverdesand Alfredo Pinto da Conceição Neto, who enabled the data sharing and instrumentation of the bridge over the Jaguari River; to the Laboratory of Topography and Geodesy of the Department of Transportation Engineering of EPUSP, for lending the JAVAD chokering antenna; to CNPq for the research productivity scholarship, and also to the JAVAD programming team.
REFERENCES
[1] ANDRADE R. G. M., et al. (2013). Comparison and calibration of numerical models from monitoring data of a reinforced concrete highway bridge. IBRACON, vol. 6, n.1, p. 121-138.São Paulo, 2013. [2] ARAUJO NETO, J. O., et al., (2013). Monitoring the Vertical Deflections of the Small Concrete Bridge with the adapted Phase Residual Method using High Rate GPS Data. In: 2nd Joint International Symposium on Deformation Monitoring (JISDM), 2013, Nottingham, Inglaterra. [3] BARBOSA A. C. B. (2007)Estudo da Variabilidade Acoplada Oceano – Atmosfera no Atlântico.Dissertação (mestrado), IAG/USP – São Paulo, 2007. [4] BARBOSA A. C. B.;BLITZKOW D. (2008).Wavelet: History and Application. Lecture Notes. Institute of Astronomy, Geophysics and Atmospheric Sciences – University Sao Paulo - IAG/USP and POLI/USP. May, 2008. [5] BRIGHAM E. O. (1974).The Fast Fourier Transform. New Jersey: Prentice-Hall, 1rd ed.,cap. 1, p.1–8, 1974. [6] DAUBECHIESI.,et al. (1992).Introduction to the special issue on Wavelet Transforms and Multiresolution Signal Analysis.IEEE Transactions on Information Theory, vol. 38, n.2, p. 528–531, March 1992. [7] GOSWAMI, J. C.; CHAN, A. K. (2011). Fundamentals of wavelets. Microwave and Optical Engineering. Wiley Interscience, New Jersey, 2nd edition, 2011. Chang, K. ed. [8] KUMAR J. P. K, and JOLLY N. (2004).Michelson Interferometer, Kamaljeeth Instrumentation & Service Unit. India, vol. 4, n.3, p. 180–192, September 2004. [9] LAROCCA A. P. C., et al. (2009). Improving Detection of Low Frequency Vibrations using High Rate Data and Filtering Techniques in Time Series of GPS Baseline. 22nd International Meeting of the Satellite Division of The Institute of Navigation, Savannah, GA, p. 1867–1875. September, 2009. [10] LAROCCA, A. P. C. (2004). O Uso do GPS como Instrumento de Controle de Deslocamentos Dinâmicos de Obras Civis. Tese (Doutorado), Escola de Engenharia de São Carlos, Universidade de São Paulo, 193 p., 2004. [11] LAROCCA, A. P. C., et al. (2012). Use of a Single L1 GPS Receiver for Monitoring Structures: First Results of the Detection of Millimetric Dynamic Oscillations. Journal of Surveying Engineering, v. 138, p. 92, 2012. [12] LAROCCA, A. P. C. et al. (2013). L1 GPS as Tool for Monitoring the Dynamic Behavior of Large Bridges In: Global Navigation Satellite Systems - From Stellar to Satellite Navigation. 1. ed. New York : InTech. , 2013. , v.1. , p. 117-144. [13] LEICK A. (2004).GPS Satellite Surveing. New York: John Willey & Sons, 3rd ed., 2004. [14] MORETTIN, P.A. (2013). Ondas e Ondaletas: Da Análise de Fourier à Análise de Ondaletas de Séries Temporais. 2ed .São Paulo: Editora USP. 2013. [15] MORLET J. (1983) Sampling Theory and Wave Propagation. NATO ASI Series, Vol. F1, p. 233–261 Springer, Berlin 1983.
12. Dynamic Monitoringvertical Deflectionof Small Concrete Bridge Using Conventional Sensors And
International organization of Scientific Research 20 | P a g e
[16] NGUYEN, R. Y.; DEL-CASTILLO-NEGRETE, D.; SCHNEIDER, K.; FARGE, M.; CHEN, G. (2010). Wavelet-based density estimation for noise reduction in plasma simulations using particles. Journal of Computational Physics, 229, 2010, 2821-2839. [17] SCHAAL R. E.; LAROCCA A. P. C. (2002). A Methodology for Monitoring Vertical Dynamic Sub- Centimeter Displacements with GPS. GPS Solutions, New York, vol. 5, n.3, p. 15–18, February 2002. [18] SINDICATO DA ARQUITETURA E DA ENGENHARIA (SINAENCO).Infra-Estrutura da Cidade de São Paulo: Prazo deValidade Vencido, São Paulo, 2007.
[19] SOUZA, E. M., et al.(2009) Redução do efeito do multicaminho de freqüências alta e baixa no posicionamento relativo cinemático utilizando wavelets: resultados preliminares. Boletim de Ciências Geodésicas (Impresso), v. 15, p. 142-156, 2009. [20] WELLS D., et al.(1986)Guide of GPS Positioning. Canadian GPS Associates, New Brunswick, Canada,1986.