This thesis analyzes the stability of pillars and subsidence in an underground coal mine. It presents the objectives, methodology, and structure of the thesis. The literature review covers the basic principles of pillar design, including estimating pillar load using tributary area theory, pillar strength formulas, and pillar safety factors. Pillar design aims to maximize coal extraction while maintaining stable pillars. Subsidence from mining needs to be managed. The case study describes the mine site and presents observations of maximum subsidence, subsidence profiles, and how subsidence changes over time and distance from mining panels. Geo-mining parameters, lithology, empirical modeling, and numerical modeling are discussed to analyze pillar stability and subsidence behavior at the mine site. Results and
Optimization of Blasting Parameters in open cast minesAnurag Jha
The document discusses drilling and blasting techniques used in large open cast mines. It describes the different types of drilling systems including percussion, rotary, and rotary-percussion drilling. It also discusses the various explosives and blasting patterns used, including single and multi-row firing patterns. Finally, it introduces the concept of optimizing blasting parameters to improve fragmentation and reduce costs.
DESIGN OF SUPPORT SYSTEM IN BORD AND PILLAR MINEAnurag Jha
This document describes a project report submitted by Anurag Kumar Jha for the partial fulfillment of requirements for a dual degree in mining engineering. The report focuses on designing a support system for bord and pillar mines. Currently, CMRI-RMR and NGI-Q systems are commonly used in Indian coal mines to estimate rock load and design support. However, calculations using NGI-Q can be time-consuming. The objective of this project is to use formulas involving only the CMRI-RMR parameter to quickly calculate rock load in development areas, at junctions, in slices, and at goaf edges to facilitate timely support design. The literature review covers the parameters used in CMRI-RMR and N
Blast hole drilling is a technique used in mining where holes are drilled into rock, packed with explosives, and detonated. The seminar discusses the blast hole drilling process, which involves drilling holes, loading explosives into the holes, detonating the explosives to blast the rock, ventilating smoke and fumes, removing blasted rock, and installing ground support. Different drill hole patterns, explosives, and the typical drilling and blasting cycle are also covered.
pillar design in coal mines, different pillar design approaches, salmon versus sheorey formulae, panel stability, diffrent approaches, local mine stiffness
The document discusses underground metal mining methods. It describes operations like exploration, development, and mining of ore from a stope. Stoping methods are classified based on support as naturally supported, artificially supported, or caved stopes. Naturally supported methods include room and pillar mining and sublevel stoping. Artificially supported methods include shrinkage stoping and cut and fill stoping. Caved stope methods include sublevel caving and block caving. Parameters to consider when choosing a stoping method include geo-mechanical conditions, ore reserves and grades, costs, productivity, and available equipment.
1. Long hole drilling and blasting techniques are key to achieving high production rates in underground metal mines.
2. Precise long hole drilling allows for larger sublevel spacing and vertical crater retreat (VCR) mining which improves efficiency and productivity.
3. In VCR mining, parallel long holes are drilled and charged in horizontal slices which are blasted in a spherical pattern for effective fragmentation. Drilling is completed before slice blasting begins.
The document discusses Down-The-Hole (DTH) drilling. DTH drilling involves a mini jackhammer located behind the drill bit that breaks rock into small pieces. It is a fast way to drill hard rock and can drill holes up to 4500 meters deep. DTH drilling is commonly used for mining, exploration, water wells, geothermal applications, and construction. Compared to rotary drilling, DTH drilling can drill deeper holes at a lower cost per meter due to the direct impact of the hammer on the bit.
The document provides information about highwall mining technology. It discusses how highwall mining can extract coal from the face of a coal seam under a highwall in a surface mine. It notes that SCCL is the first company implementing this technology in India at certain mines. Highwall mining provides an economical way to extract coal reserves locked in the highwall that would otherwise be lost. The technology involves driving parallel entries into the coal seam without artificial support using auger heads or continuous miners.
Optimization of Blasting Parameters in open cast minesAnurag Jha
The document discusses drilling and blasting techniques used in large open cast mines. It describes the different types of drilling systems including percussion, rotary, and rotary-percussion drilling. It also discusses the various explosives and blasting patterns used, including single and multi-row firing patterns. Finally, it introduces the concept of optimizing blasting parameters to improve fragmentation and reduce costs.
DESIGN OF SUPPORT SYSTEM IN BORD AND PILLAR MINEAnurag Jha
This document describes a project report submitted by Anurag Kumar Jha for the partial fulfillment of requirements for a dual degree in mining engineering. The report focuses on designing a support system for bord and pillar mines. Currently, CMRI-RMR and NGI-Q systems are commonly used in Indian coal mines to estimate rock load and design support. However, calculations using NGI-Q can be time-consuming. The objective of this project is to use formulas involving only the CMRI-RMR parameter to quickly calculate rock load in development areas, at junctions, in slices, and at goaf edges to facilitate timely support design. The literature review covers the parameters used in CMRI-RMR and N
Blast hole drilling is a technique used in mining where holes are drilled into rock, packed with explosives, and detonated. The seminar discusses the blast hole drilling process, which involves drilling holes, loading explosives into the holes, detonating the explosives to blast the rock, ventilating smoke and fumes, removing blasted rock, and installing ground support. Different drill hole patterns, explosives, and the typical drilling and blasting cycle are also covered.
pillar design in coal mines, different pillar design approaches, salmon versus sheorey formulae, panel stability, diffrent approaches, local mine stiffness
The document discusses underground metal mining methods. It describes operations like exploration, development, and mining of ore from a stope. Stoping methods are classified based on support as naturally supported, artificially supported, or caved stopes. Naturally supported methods include room and pillar mining and sublevel stoping. Artificially supported methods include shrinkage stoping and cut and fill stoping. Caved stope methods include sublevel caving and block caving. Parameters to consider when choosing a stoping method include geo-mechanical conditions, ore reserves and grades, costs, productivity, and available equipment.
1. Long hole drilling and blasting techniques are key to achieving high production rates in underground metal mines.
2. Precise long hole drilling allows for larger sublevel spacing and vertical crater retreat (VCR) mining which improves efficiency and productivity.
3. In VCR mining, parallel long holes are drilled and charged in horizontal slices which are blasted in a spherical pattern for effective fragmentation. Drilling is completed before slice blasting begins.
The document discusses Down-The-Hole (DTH) drilling. DTH drilling involves a mini jackhammer located behind the drill bit that breaks rock into small pieces. It is a fast way to drill hard rock and can drill holes up to 4500 meters deep. DTH drilling is commonly used for mining, exploration, water wells, geothermal applications, and construction. Compared to rotary drilling, DTH drilling can drill deeper holes at a lower cost per meter due to the direct impact of the hammer on the bit.
The document provides information about highwall mining technology. It discusses how highwall mining can extract coal from the face of a coal seam under a highwall in a surface mine. It notes that SCCL is the first company implementing this technology in India at certain mines. Highwall mining provides an economical way to extract coal reserves locked in the highwall that would otherwise be lost. The technology involves driving parallel entries into the coal seam without artificial support using auger heads or continuous miners.
This document provides an overview of blasting in open cast mines, including the various types of explosives used. It discusses low explosives like gunpowder as well as high explosives like nitroglycerin, dynamite, ANFO, LOX, slurry, and emulsion explosives. The advantages and disadvantages of each type are outlined. The document also discusses the use of bulk explosives and various bulk delivery systems. Key conditions for safely using bulk explosives on site are described.
Subsidence is one of the major environmental issues related to underground mining industry. This presentation gives an insight to causes, nature, effect of subsidence and some mitigation measures.
This document provides an overview of shaft sinking methods for underground mining. It discusses traditional methods like wood/steel piling and open caisson as well as more advanced techniques like vertical shaft sinking machines (VSM) and shaft boring systems. The document highlights the advantages of mechanical excavation methods like VSMs in providing higher production rates and safety compared to traditional drill and blast operations. It analyzes case studies of shafts sunk in India and concludes that using advanced technologies could have increased production rates by 30% while improving safety and reducing costs compared to conventional shaft sinking methods.
The document discusses design parameters for opencast mine benches. It outlines that bench width should be at least twice the width of the largest hauling vehicle plus clearance. The bench face slope is usually maintained at 60 degrees from horizontal. Haul roads should be at least three times the width of the largest vehicle and have a gradient of 1 in 16 to allow movement of haul trucks. Short ramps between benches can have a steeper gradient of 1 in 10 for heavy machinery.
This document discusses various techniques for raising, which is the vertical or steeply inclined excavation that connects different levels in underground mines. The key raising techniques discussed include open raising using drilling and blasting in short lengths, compartment method which divides the raise into sections, Alimak raise climber which uses a rack and pinion mechanism, longhole raising using long parallel drill holes, drop raising which uses large diameter blast holes, Jora hoist with a caged platform, and raise borers which drill and ream a circular raise without explosives. The Alimak raise climber is noted as generally the best adopted technique, first used in India in 1972.
The document discusses techniques for open pit mining blasts, including:
- Major factors like attitude, communication, blast design, and geological effects influence blast efficiency
- Proper blast design considers uniform energy distribution, confinement, energy level, and design adjustments for conditions
- Geological effects like rock properties, structure, water, and seam orientations impact blasting results more than explosive properties
- Basic blast design considerations include bench height, hole diameter, burden, spacing, stemming, and decking
Subsidence occurs when underground coal mine workings collapse, causing sinking of the ground surface. It usually appears as sinkholes or troughs. Many factors influence the extent of subsidence, including seam depth and thickness, roof and floor competence, extraction method, and degree of extraction. Subsidence can damage surface structures and is measured through surface observations, subsurface techniques like wireline logging, and predictive models ranging from empirical to numerical modeling.
This document discusses mine explosions caused by methane gas (firedamp) ignition. It provides details on:
1) What mine explosions are, their main causes being firedamp or coal dust ignition. The worst Indian disaster killed 268 miners at Dhori Colliery in 1965.
2) The properties of firedamp (methane gas), including its flammable limits and factors influencing ignitability like temperature and concentration.
3) Potential ignition sources in mines including blasting, fires, sparks from damaged safety lamps or friction from cutting or drilling equipment. Negligence by miners is also a cause.
This document discusses roof support in underground coal mines. There are two main types of roof support: intrinsic supports like roof bolts that are installed within the roof, and standing supports like timber props that are installed between the roof and floor. Timber supports are commonly used in Indian coal mines due to low cost and availability, though metal supports offer higher load capacity. A case study examines how roof bolts were used with a specific layout and spacing in the Tandshi coal mine in India. Proper roof support is necessary to prevent roof collapse and protect miners from rock falls.
theories of interaction of rock cutting tools in contact with the rock, different parameters, specific energy, applications, drag, point attack picks, disc cutters, and their interaction
In this ppt you will get all information regarding shaft sinking. Like what is permanent lining and temporary lining. How to decide shape of shaft, drilling blasting, support, lighting in shaft. Use of shaft and skips.
development of main headings and gate roads with the use of road heading and bolter miners has paramount importance for effective production from a Longwall mine
Optimisation of drilling and blasting focussing on fly rockSafdar Ali
This document discusses optimizing drilling and blasting to minimize fly rock in surface mining. Fly rock, which is rock propelled from the blast area, is a major safety hazard and cause of accidents. The document reviews factors that influence fly rock like burden, stemming, charging, and geology. It presents three models for predicting maximum fly rock distance and discusses field data collection and analysis from limestone quarry blasts to validate the models. Recommendations are provided to control fly rock through improved blast design, site controls, crew experience, and covering exposed areas.
In this pdf one can get the different types of equipment used in surface mines which is very important from the examination point of view. important regulations are also included in this .
This document provides an overview of rock blasting fundamentals, including the types of explosives, initiation systems, circuits, blasthole loading, blast design, and geology considerations. It describes the main categories of explosives as nitroglycerin-based, dry blasting agents, and slurries. Detonators and delay series are discussed as the means of initiation. The three main circuit types - series, parallel-series, and parallel - are also summarized. Guidelines for blasthole loading, blast design based on geology, and selecting powder factors are presented at a high level.
This document discusses blasting in mining operations. It begins by explaining that blasting is used to break rock into smaller pieces for mining and quarrying, or to create space. The objectives of blasting are to extract material at minimum cost while meeting production quality and quantity requirements. It then covers the different types of explosions, explosives, detonation and deflagration processes, properties and types of explosives, initiating systems including electrical, non-electric, detonating cord, and blast design considerations like burden, spacing, stemming, and bench height.
This document discusses the bord and pillar mining method. It begins by introducing bord and pillar mining and explaining that it involves driving parallel roads separated by coal pillars.
It then explains some key aspects of bord and pillar design, including that the optimal pillar size is critical to ensure stability without leaving too much coal behind. Pillar size needs to increase with depth and road width.
The document also provides details on factors that influence pillar design, such as seam strength and thickness, roof and floor conditions, extraction percentage, and depth. Formulas are presented for calculating pillar stress, strength, and safety factors.
The document summarizes Om Prakash Yadav's summer internship report on a construction project. It includes sections on construction steps, materials and equipment used, and quality control measures. Key details are an internship at Larsen & Toubro constructing Kaveri Apartments for Lucknow Development Authority. Construction involved site clearance, surveying, excavation, foundation work, and erecting the building frame through beams and columns before finishing work. Aluminum formwork and a total station were utilized.
This document provides an overview of blasting in open cast mines, including the various types of explosives used. It discusses low explosives like gunpowder as well as high explosives like nitroglycerin, dynamite, ANFO, LOX, slurry, and emulsion explosives. The advantages and disadvantages of each type are outlined. The document also discusses the use of bulk explosives and various bulk delivery systems. Key conditions for safely using bulk explosives on site are described.
Subsidence is one of the major environmental issues related to underground mining industry. This presentation gives an insight to causes, nature, effect of subsidence and some mitigation measures.
This document provides an overview of shaft sinking methods for underground mining. It discusses traditional methods like wood/steel piling and open caisson as well as more advanced techniques like vertical shaft sinking machines (VSM) and shaft boring systems. The document highlights the advantages of mechanical excavation methods like VSMs in providing higher production rates and safety compared to traditional drill and blast operations. It analyzes case studies of shafts sunk in India and concludes that using advanced technologies could have increased production rates by 30% while improving safety and reducing costs compared to conventional shaft sinking methods.
The document discusses design parameters for opencast mine benches. It outlines that bench width should be at least twice the width of the largest hauling vehicle plus clearance. The bench face slope is usually maintained at 60 degrees from horizontal. Haul roads should be at least three times the width of the largest vehicle and have a gradient of 1 in 16 to allow movement of haul trucks. Short ramps between benches can have a steeper gradient of 1 in 10 for heavy machinery.
This document discusses various techniques for raising, which is the vertical or steeply inclined excavation that connects different levels in underground mines. The key raising techniques discussed include open raising using drilling and blasting in short lengths, compartment method which divides the raise into sections, Alimak raise climber which uses a rack and pinion mechanism, longhole raising using long parallel drill holes, drop raising which uses large diameter blast holes, Jora hoist with a caged platform, and raise borers which drill and ream a circular raise without explosives. The Alimak raise climber is noted as generally the best adopted technique, first used in India in 1972.
The document discusses techniques for open pit mining blasts, including:
- Major factors like attitude, communication, blast design, and geological effects influence blast efficiency
- Proper blast design considers uniform energy distribution, confinement, energy level, and design adjustments for conditions
- Geological effects like rock properties, structure, water, and seam orientations impact blasting results more than explosive properties
- Basic blast design considerations include bench height, hole diameter, burden, spacing, stemming, and decking
Subsidence occurs when underground coal mine workings collapse, causing sinking of the ground surface. It usually appears as sinkholes or troughs. Many factors influence the extent of subsidence, including seam depth and thickness, roof and floor competence, extraction method, and degree of extraction. Subsidence can damage surface structures and is measured through surface observations, subsurface techniques like wireline logging, and predictive models ranging from empirical to numerical modeling.
This document discusses mine explosions caused by methane gas (firedamp) ignition. It provides details on:
1) What mine explosions are, their main causes being firedamp or coal dust ignition. The worst Indian disaster killed 268 miners at Dhori Colliery in 1965.
2) The properties of firedamp (methane gas), including its flammable limits and factors influencing ignitability like temperature and concentration.
3) Potential ignition sources in mines including blasting, fires, sparks from damaged safety lamps or friction from cutting or drilling equipment. Negligence by miners is also a cause.
This document discusses roof support in underground coal mines. There are two main types of roof support: intrinsic supports like roof bolts that are installed within the roof, and standing supports like timber props that are installed between the roof and floor. Timber supports are commonly used in Indian coal mines due to low cost and availability, though metal supports offer higher load capacity. A case study examines how roof bolts were used with a specific layout and spacing in the Tandshi coal mine in India. Proper roof support is necessary to prevent roof collapse and protect miners from rock falls.
theories of interaction of rock cutting tools in contact with the rock, different parameters, specific energy, applications, drag, point attack picks, disc cutters, and their interaction
In this ppt you will get all information regarding shaft sinking. Like what is permanent lining and temporary lining. How to decide shape of shaft, drilling blasting, support, lighting in shaft. Use of shaft and skips.
development of main headings and gate roads with the use of road heading and bolter miners has paramount importance for effective production from a Longwall mine
Optimisation of drilling and blasting focussing on fly rockSafdar Ali
This document discusses optimizing drilling and blasting to minimize fly rock in surface mining. Fly rock, which is rock propelled from the blast area, is a major safety hazard and cause of accidents. The document reviews factors that influence fly rock like burden, stemming, charging, and geology. It presents three models for predicting maximum fly rock distance and discusses field data collection and analysis from limestone quarry blasts to validate the models. Recommendations are provided to control fly rock through improved blast design, site controls, crew experience, and covering exposed areas.
In this pdf one can get the different types of equipment used in surface mines which is very important from the examination point of view. important regulations are also included in this .
This document provides an overview of rock blasting fundamentals, including the types of explosives, initiation systems, circuits, blasthole loading, blast design, and geology considerations. It describes the main categories of explosives as nitroglycerin-based, dry blasting agents, and slurries. Detonators and delay series are discussed as the means of initiation. The three main circuit types - series, parallel-series, and parallel - are also summarized. Guidelines for blasthole loading, blast design based on geology, and selecting powder factors are presented at a high level.
This document discusses blasting in mining operations. It begins by explaining that blasting is used to break rock into smaller pieces for mining and quarrying, or to create space. The objectives of blasting are to extract material at minimum cost while meeting production quality and quantity requirements. It then covers the different types of explosions, explosives, detonation and deflagration processes, properties and types of explosives, initiating systems including electrical, non-electric, detonating cord, and blast design considerations like burden, spacing, stemming, and bench height.
This document discusses the bord and pillar mining method. It begins by introducing bord and pillar mining and explaining that it involves driving parallel roads separated by coal pillars.
It then explains some key aspects of bord and pillar design, including that the optimal pillar size is critical to ensure stability without leaving too much coal behind. Pillar size needs to increase with depth and road width.
The document also provides details on factors that influence pillar design, such as seam strength and thickness, roof and floor conditions, extraction percentage, and depth. Formulas are presented for calculating pillar stress, strength, and safety factors.
The document summarizes Om Prakash Yadav's summer internship report on a construction project. It includes sections on construction steps, materials and equipment used, and quality control measures. Key details are an internship at Larsen & Toubro constructing Kaveri Apartments for Lucknow Development Authority. Construction involved site clearance, surveying, excavation, foundation work, and erecting the building frame through beams and columns before finishing work. Aluminum formwork and a total station were utilized.
Slides of the talk on Koide Formula. Video should be available at http://viavca.in2p3.fr/alejandro_rivero.html
or directly al flv
http://viavca.in2p3.fr/video/alejandro_rivero.flv
Land subsidence: what is it and why do we care?EMA-tucson
The document discusses land subsidence, which is the sinking or settling of land caused by underground water withdrawal. It notes that groundwater overdraft is the principal cause of subsidence, and it has impacted over 1,200 square miles in Arizona, with up to 20 feet of subsidence measured. The document outlines how subsidence occurs, where it is located nationally and in Arizona, its impacts such as damage to infrastructure and earth fissures, monitoring techniques, and potential mitigation strategies.
The document discusses different methods of coal extraction from underground mines including diagonal, step diagonal, and steep diagonal lines of extraction. It also covers angles of extraction and support systems used for extraction by hand and with longwall mining equipment.
The structural engineer inspected Patil Sadan to evaluate its structural stability. [The engineer] inspected foundations, columns, beams, and slabs, and performed non-destructive tests to estimate the strength of materials. [The engineer] determined the building required strengthening measures to address distress, developed method statements, and repaired the building accordingly. [The engineer] certified the building is now structurally stable and safe for users.
This document provides an overview of certification and inspection for offshore drilling units. It discusses the three main certification authorities: coastal state authorities, classification societies, and the country of registry or flag state. Coastal states establish rules for offshore areas under their jurisdiction. Classification societies set standards for design, construction, and operation of vessels. The flag state accepts the drilling unit and issues certificates demonstrating compliance with international standards. The document also provides background on the International Maritime Organization, the specialized UN agency responsible for improving maritime safety and preventing pollution.
VOCATIONAL TRAINING REPORT @ NTPC VINDHYACHALMilind Punj
The document is a vocational training report submitted by Milind Punj to fulfill the requirements for a Bachelor of Technology degree in Electrical Engineering. It provides an overview of Milind's training at the NTPC Vindhyachal thermal power station located in Singrauli District, Madhya Pradesh, India. The report includes an acknowledgements section, introduction to NTPC Ltd and the NTPC Vindhyachal power plant, descriptions of the power generation process and basic plant components, and a conclusion. Milind conducted his training from May 15th to June 14th 2014 under the guidance of Mr. A. Markhedkar, focusing on various electrical and operational aspects of the thermal power station.
This document is a project report submitted by Ravi Kumar Ch in partial fulfillment of the requirements for a Master of Business Administration degree from Gayatri Vidya Parishad College. The report studies financing to MSMEs from both the perspective of banks and borrowers, with reference to Andhra Bank's zonal office in Visakhapatnam. The report includes an introduction, industry profile, Andhra Bank profile, conceptual framework, analysis and interpretation of data, findings and suggestions, and conclusion. The objectives are to learn financing procedures for MSMEs and study borrower opinions on funding norms and criteria. The scope is limited to one Andhra Bank zone and businesses in Visakhapatnam.
Longwall mining is a major method of underground coal extraction worldwide. In India, coal accounts for over 50% of energy production, though most is still extracted via opencast mines. Longwall mining was introduced to India in the 1970s but has seen limited improvement and adoption since. Key longwall equipment includes powered roof supports, shearers, conveyors, and monitoring is important for strata control and safety. Organizing longwall panels and transferring equipment between panels is a complex operation involving dismantling, transport and reassembly of machinery.
Final Project Report on Recruitment & SelectionMdsamim143
The document is a summer training report submitted by Md. Samim for their Master of Business Administration (MBA) program. It discusses their training at Skope Business Ventures Pvt. Ltd., a recruitment firm, where they explored the topic of recruitment and selection processes. The report includes an introduction of the company, acknowledgements, table of contents, and initial chapters covering the objectives of the study and introductions to recruitment, factors affecting recruitment, sources of recruitment, and recruitment policies and philosophies.
Project report on recruitment and selection at cmpdiKumari Pswn
This document provides information about a project report on recruitment and selection at Central Mine Planning and Design Institute (CMPDI) in India. It includes a declaration, certificate of completion, acknowledgements, executive summary, and table of contents. The project report evaluates CMPDI's manpower planning process and recruitment and selection procedures. It contains the student's research findings, conclusions, and recommendations after studying CMPDI's practices from May to June 2014.
physico mechanical properties of rock materials and details of different laboratory as well as field tests for determining behaviour of different rock materials in the field of mining and civil engineering
Open pit mining involves digging a large hole or pit at the earth's surface to extract ore deposits near the surface. Overburden or waste rock is removed to expose the ore body, which is then extracted using large excavating equipment like shovels and haul trucks. Ore is transported from the pit either by truck or conveyor belt to a processing facility. Open pit mining provides high productivity and low costs but requires significant capital investment and can have large environmental impacts due to the large scale of surface disturbance. It is best suited to deposits that are relatively shallow and large in area.
Underground surveying requires different techniques than surface surveying due to challenging conditions like heat, moisture, darkness and danger. Key points covered:
- Underground control networks must be connected and oriented to surface networks by obtaining coordinates of underground stations and bearings of underground lines relative to surface lines.
- Modern surveying tools like Leica fieldPro software integrate 3D CAD with data collection to enable one-person face mapping and daily mine survey updates for accurate planning.
- Leica GeoMoS provides automatic deformation monitoring systems for underground asset protection.
Explosives, Theory Of Breakage And Blasting Operationspartha sharma
This document discusses explosives and blasting operations. It defines different types of explosives and their ingredients and functions. It explains how to compare explosives based on their properties like strength, detonation velocity, density etc. It describes drilling systems and the theory of rock breakage through radial cracking and flexural rupture. Finally, it discusses blast design factors and different controlled blasting techniques like line drilling, cushion blasting, smooth-wall blasting and pre-splitting used to control overbreak.
subsidence, upsidence, subsidence limits, components of subsidence, prediction of subsidence, analysis of subsidence, coal mines, control of subsidence, subsidence trough, harmonic extraction, abandoned mines subsidence prevention, subsidence prevention in working coal mines, factors affecting subsidence
This work is done as a part of B.Tech. degree requirements in Spring 2013 (Jan-May'13). The author was pursuing B.Tech. in Civil Engineering at the National Institute of Technology Tiruchirappalli during the making of this project.
This document summarizes the design and construction of a variable geometry, supersonic wind tunnel by a group of WPI students. It provides background on supersonic wind tunnel design using the method of characteristics. It then describes the initial calculations performed to determine design constraints. The key features of the designed tunnel include flexible polystyrene contours to allow achieving various test section Mach numbers and adjustable mechanisms to control the throat, expansion, and diffuser sections. Construction of the tunnel was not fully completed within the project timeframe.
This project report summarizes an experimental study conducted to evaluate the bond strength of concrete. Samples of concrete were made with varying grades of concrete, diameters of reinforcing bars, and with or without kinks in the bars. A pull-out test was used to measure the bond strength of each sample. The results will be analyzed to verify bond strength values provided in design codes and understand how factors like concrete grade and bar properties affect bond strength. The study aims to provide data on concrete bond strength under various conditions to improve structural design and construction.
The author discusses the importance of properly designing pillars in underground coal mining to ensure stability and prevent disasters from sudden pillar collapses. Current statutory guidelines for pillar dimensions are limited and not scientifically based. The author suggests a modified formula for calculating pillar loads that considers both static loads from overburden strata as well as dynamic loads experienced during pillar extraction, which can cause premature collapses if pillars are not strong enough. The dynamic load factor would depend on the extraction method used - being close to 1 for sand stowing but much higher for caving methods. Proper pillar design accounting for both static and dynamic loads is critical to maintain safety during coal extraction.
The document discusses the design of pillars in underground coal mining. It notes that pillar failure can be gradual or sudden, with sudden failures causing disasters. Statutory guidelines exist for pillar dimensions but have limitations. The author proposes a modified formula to calculate pillar load that includes a dynamic load factor to account for loads during pillar extraction. Pillar strength is typically estimated using empirical formulas that the author critiques. The author suggests experience and site conditions be considered to better estimate pillar strength for ensuring stability of underground workings.
The document summarizes the planning, analysis, and design of a multispecialty hospital building. It includes the objectives to prepare architectural drawings, analyze the G+2 building using STAAD Pro, and design the building according to IS 456:2000 using the working stress method. It describes analyzing the building's ability to resist lateral loads. Maximum bending moments in beams and columns will depend on their relative rigidity. Structural elements like slabs, beams, columns, footings, and staircases will be designed according to code specifications using the working stress method.
- The design of pillars is a critical aspect of underground pillar mining to ensure strata control and prevent sudden, catastrophic pillar collapses.
- Statutory guidelines exist for pillar dimensions but have limitations as they are based only on past experience and do not consider dynamic loading or scientific analysis.
- The author suggests a modified formula for calculating pillar load that includes a dynamic load factor to account for loads during pillar extraction, which are different depending on the extraction method.
This document discusses the design of pillars in underground coal mining. It notes that pillar failure can be either gradual or sudden, with sudden failures causing disasters. Statutory guidelines for pillar dimensions are provided but have limitations as mine depths increase. The author proposes modifications to the standard formula for calculating rock load on pillars to account for dynamic loads during pillar extraction, with a dynamic load factor. Two common formulas for estimating pillar strength are examined, with the author noting limitations and suggesting greater consideration of pillar width in the calculations. Overall, the author aims to provide a more scientifically-based approach to pillar design for stability during formation and extraction.
This document discusses the design of pillars in underground coal mining. It notes that pillar failure can be either gradual or sudden, with sudden failures causing disasters. Statutory guidelines for pillar dimensions are provided but have limitations as mine depths increase. The author proposes modifications to the standard formula for calculating rock load on pillars to account for dynamic loads during pillar extraction, with a dynamic load factor. Two common formulas for estimating pillar strength are examined, with the author noting limitations and making suggestions to better account for depth and pillar width factors. Overall, the author aims to provide a more scientifically-based approach to pillar design for stability during formation and extraction.
This document summarizes a thesis titled "Reliability Analysis of Reinforced Concrete Shallow Footings Designed Using BNBC 2006" submitted by Sukanta Kumer Shill to the Department of Civil Engineering at Dhaka University of Engineering and Technology in partial fulfillment of a Master of Science degree in Civil Engineering in February 2015. The thesis performs reliability analysis on reinforced concrete shallow footings designed according to the Bangladesh National Building Code (BNBC) 2006 provisions to evaluate their safety and reliability considering uncertainties in loads and material strengths. Three model buildings of different heights are designed and analyzed to determine the failure probabilities and reliability indices of their footings against different limit states such as bearing capacity failure, punching shear failure, flexural
Structural Health Monitoring and Strengthening Of BridgesStructural Health Mo...Editor IJCATR
This paper presents one bridge which were either rehabilitated or strengthened by using FRP composites. The resulting
structure was then tested for the effect after using FRP composites for Rehabilitation and strengthening. In this paper, Structural
Health Monitoring basics are covered and need for SHM in future in or India scenario. Use of FRP composites in Rehabilitation
and Strengthening of structures is becoming increasingly popular and is opening new possibilities in construction and rehabilitation
of structures.
Structural Health Monitoring and Strengthening Of BridgesEditor IJCATR
This paper presents one bridge which were either rehabilitated or strengthened by using FRP composites. The resulting structure was then tested for the effect after using FRP composites for Rehabilitation and strengthening. In this paper, Structural Health Monitoring basics are covered and need for SHM in future in or India scenario. Use of FRP composites in Rehabilitation and Strengthening of structures is becoming increasingly popular and is opening new possibilities in construction and rehabilitation of structures.
The document proposes a design for UniArc Residences, a student residence building at Infrastructure University Kuala Lumpur using shipping containers. The 16-level building would house 990 rooms across 3 blocks using different sized containers. Structural analysis using STAAD.Pro shows the steel structure of columns, beams, and bolted connections can support the container loads. Shipping containers provide cost and construction benefits over traditional materials.
This document discusses the development of a rational seismic design methodology for transportation tunnels, with the goals of maintaining a consistent seismic design philosophy and developing simple yet rational analysis methods for different tunnel section geometries. It provides background on the importance of seismic design for underground structures based on earthquake performance data, and summarizes the scope of developing analysis methods for evaluating earthquake effects on circular and rectangular tunnel sections.
This document summarizes Dimitrios Nikoloutsopoulos' master's thesis on developing ultra-sharp pyramidal pits in silicon substrates for molding atomic force microscope tips. It explores techniques for etching silicon wafers to create perfectly pyramidal pits, including rotating the etching mask to different angles relative to the silicon crystal orientation. Experimental techniques tested include rotating square mask openings, using masks with different shaped openings, and bonding two wafers rotated 45 degrees to create perfectly square etch masks. Sharpening effects are investigated using wet and dry etching, with wedge-shaped apexes as small as ~20 nm successfully reported.
This document is a thesis submitted by Saptadip Sarkar in partial fulfillment of the requirements for a Bachelor of Technology degree in Civil Engineering from the National Institute of Technology, Rourkela. The thesis involves the design of an earthquake-resistant multi-story reinforced concrete building on a sloping ground. It includes an introduction describing the importance of seismic design for tall buildings and the poor performance of short columns during past earthquakes. The thesis will analyze simple 2D reinforced concrete frames of varying heights and bay sizes using STAAD Pro software and compare the results between frames on level and sloping ground. It will also include the ductility design and detailing of structural members.
Modelling Analysis and Design of Self Anchored Suspension BridgeRohit Grandhi, EIT
The application of earlier course works in this project is summarized in Table 1.2:
Table 1.2 Application of earlier course work
Course Work Application in Project
Structural Analysis Analysis of loads, stresses and deformations of structural elements.
Structural Design Design of deck slab, girder, cables, suspenders as per codes.
Concrete Technology Design of M25 grade concrete mix.
Steel Structures Design of reinforcement details.
Geotechnical Engineering Foundation design not included in scope.
Construction stage analysis of rcc frames project reportSayyad Wajed Ali
While analyzing a multistorey building frame, conventionally all the probable loads are applied after modeling the entire building frame. But in practice the frame is constructed in various stages. Accordingly, the stability of frame varies at every construction stage. Even during construction freshly placed concrete floor is supported by previously cast floor by formwork. Thus, the loads assumed in conventional analysis will vary in transient situation. Obviously, results obtained by the traditional analysis will be unsuitable. Therefore, the frame should be analyzed at every construction stage taking into account variation in loads. The phenomenon known as Construction Stage Analysis considers these uncertainties precisely. This paper analyzes several numbers of multistorey reinforced concrete building frames of different bay width and length, storey height and number of stories using STAADpro, followed by the construction stage analysis of each model. Also all full frame models are analyzed for earthquake forces in Zone - II (IS 1893 : 2002). Finally, a comparative study of Axial forces, Bending moments, Shear forces and Twisting moments was done at every storey for full frame model (without earthquake forces) and construction stage model (without earthquake forces).
EMIN Sistemas Geotecnicos. El Sistema Helipile es una solución de refuerzo para cargas de cimentaciones por medio de un elemento de acero galvanizado con forma de hélice.
The document discusses literature related to longwall mining geo-technical studies conducted at Ramagundam region in SCCL, India. It summarizes the key findings from 9 completed longwall panels at GDK.10A incline mine including production trends, geological conditions, equipment specifications, and analyses of caving behavior and periodic weighting distances for different panel lengths. Face length was found to influence main and periodic fall spans, with main fall varying between 63-78m for face lengths from 90-170m.
Similar to Analysis of subsidence and stability of pillars in a coal mine (20)
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...shadow0702a
This document serves as a comprehensive step-by-step guide on how to effectively use PyCharm for remote debugging of the Windows Subsystem for Linux (WSL) on a local Windows machine. It meticulously outlines several critical steps in the process, starting with the crucial task of enabling permissions, followed by the installation and configuration of WSL.
The guide then proceeds to explain how to set up the SSH service within the WSL environment, an integral part of the process. Alongside this, it also provides detailed instructions on how to modify the inbound rules of the Windows firewall to facilitate the process, ensuring that there are no connectivity issues that could potentially hinder the debugging process.
The document further emphasizes on the importance of checking the connection between the Windows and WSL environments, providing instructions on how to ensure that the connection is optimal and ready for remote debugging.
It also offers an in-depth guide on how to configure the WSL interpreter and files within the PyCharm environment. This is essential for ensuring that the debugging process is set up correctly and that the program can be run effectively within the WSL terminal.
Additionally, the document provides guidance on how to set up breakpoints for debugging, a fundamental aspect of the debugging process which allows the developer to stop the execution of their code at certain points and inspect their program at those stages.
Finally, the document concludes by providing a link to a reference blog. This blog offers additional information and guidance on configuring the remote Python interpreter in PyCharm, providing the reader with a well-rounded understanding of the process.
Mechatronics is a multidisciplinary field that refers to the skill sets needed in the contemporary, advanced automated manufacturing industry. At the intersection of mechanics, electronics, and computing, mechatronics specialists create simpler, smarter systems. Mechatronics is an essential foundation for the expected growth in automation and manufacturing.
Mechatronics deals with robotics, control systems, and electro-mechanical systems.
Digital Twins Computer Networking Paper Presentation.pptxaryanpankaj78
A Digital Twin in computer networking is a virtual representation of a physical network, used to simulate, analyze, and optimize network performance and reliability. It leverages real-time data to enhance network management, predict issues, and improve decision-making processes.
Applications of artificial Intelligence in Mechanical Engineering.pdfAtif Razi
Historically, mechanical engineering has relied heavily on human expertise and empirical methods to solve complex problems. With the introduction of computer-aided design (CAD) and finite element analysis (FEA), the field took its first steps towards digitization. These tools allowed engineers to simulate and analyze mechanical systems with greater accuracy and efficiency. However, the sheer volume of data generated by modern engineering systems and the increasing complexity of these systems have necessitated more advanced analytical tools, paving the way for AI.
AI offers the capability to process vast amounts of data, identify patterns, and make predictions with a level of speed and accuracy unattainable by traditional methods. This has profound implications for mechanical engineering, enabling more efficient design processes, predictive maintenance strategies, and optimized manufacturing operations. AI-driven tools can learn from historical data, adapt to new information, and continuously improve their performance, making them invaluable in tackling the multifaceted challenges of modern mechanical engineering.
Software Engineering and Project Management - Introduction, Modeling Concepts...Prakhyath Rai
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
Software Engineering and Project Management - Software Testing + Agile Method...Prakhyath Rai
Software Testing: A Strategic Approach to Software Testing, Strategic Issues, Test Strategies for Conventional Software, Test Strategies for Object -Oriented Software, Validation Testing, System Testing, The Art of Debugging.
Agile Methodology: Before Agile – Waterfall, Agile Development.
Null Bangalore | Pentesters Approach to AWS IAMDivyanshu
#Abstract:
- Learn more about the real-world methods for auditing AWS IAM (Identity and Access Management) as a pentester. So let us proceed with a brief discussion of IAM as well as some typical misconfigurations and their potential exploits in order to reinforce the understanding of IAM security best practices.
- Gain actionable insights into AWS IAM policies and roles, using hands on approach.
#Prerequisites:
- Basic understanding of AWS services and architecture
- Familiarity with cloud security concepts
- Experience using the AWS Management Console or AWS CLI.
- For hands on lab create account on [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
# Scenario Covered:
- Basics of IAM in AWS
- Implementing IAM Policies with Least Privilege to Manage S3 Bucket
- Objective: Create an S3 bucket with least privilege IAM policy and validate access.
- Steps:
- Create S3 bucket.
- Attach least privilege policy to IAM user.
- Validate access.
- Exploiting IAM PassRole Misconfiguration
-Allows a user to pass a specific IAM role to an AWS service (ec2), typically used for service access delegation. Then exploit PassRole Misconfiguration granting unauthorized access to sensitive resources.
- Objective: Demonstrate how a PassRole misconfiguration can grant unauthorized access.
- Steps:
- Allow user to pass IAM role to EC2.
- Exploit misconfiguration for unauthorized access.
- Access sensitive resources.
- Exploiting IAM AssumeRole Misconfiguration with Overly Permissive Role
- An overly permissive IAM role configuration can lead to privilege escalation by creating a role with administrative privileges and allow a user to assume this role.
- Objective: Show how overly permissive IAM roles can lead to privilege escalation.
- Steps:
- Create role with administrative privileges.
- Allow user to assume the role.
- Perform administrative actions.
- Differentiation between PassRole vs AssumeRole
Try at [killercoda.com](https://killercoda.com/cloudsecurity-scenario/)
Tools & Techniques for Commissioning and Maintaining PV Systems W-Animations ...Transcat
Join us for this solutions-based webinar on the tools and techniques for commissioning and maintaining PV Systems. In this session, we'll review the process of building and maintaining a solar array, starting with installation and commissioning, then reviewing operations and maintenance of the system. This course will review insulation resistance testing, I-V curve testing, earth-bond continuity, ground resistance testing, performance tests, visual inspections, ground and arc fault testing procedures, and power quality analysis.
Fluke Solar Application Specialist Will White is presenting on this engaging topic:
Will has worked in the renewable energy industry since 2005, first as an installer for a small east coast solar integrator before adding sales, design, and project management to his skillset. In 2022, Will joined Fluke as a solar application specialist, where he supports their renewable energy testing equipment like IV-curve tracers, electrical meters, and thermal imaging cameras. Experienced in wind power, solar thermal, energy storage, and all scales of PV, Will has primarily focused on residential and small commercial systems. He is passionate about implementing high-quality, code-compliant installation techniques.
Prediction of Electrical Energy Efficiency Using Information on Consumer's Ac...PriyankaKilaniya
Energy efficiency has been important since the latter part of the last century. The main object of this survey is to determine the energy efficiency knowledge among consumers. Two separate districts in Bangladesh are selected to conduct the survey on households and showrooms about the energy and seller also. The survey uses the data to find some regression equations from which it is easy to predict energy efficiency knowledge. The data is analyzed and calculated based on five important criteria. The initial target was to find some factors that help predict a person's energy efficiency knowledge. From the survey, it is found that the energy efficiency awareness among the people of our country is very low. Relationships between household energy use behaviors are estimated using a unique dataset of about 40 households and 20 showrooms in Bangladesh's Chapainawabganj and Bagerhat districts. Knowledge of energy consumption and energy efficiency technology options is found to be associated with household use of energy conservation practices. Household characteristics also influence household energy use behavior. Younger household cohorts are more likely to adopt energy-efficient technologies and energy conservation practices and place primary importance on energy saving for environmental reasons. Education also influences attitudes toward energy conservation in Bangladesh. Low-education households indicate they primarily save electricity for the environment while high-education households indicate they are motivated by environmental concerns.
Analysis of subsidence and stability of pillars in a coal mine
1. ANALYSIS OF SUBSIDENCE AND STABILITY OF
PILLARS IN A COAL MINE
A THESIS SUBMITTED IN PARTIAL FULFILMENT OF THE REQUIREMENTS FOR THE
DEGREE OF
Bachelor of Technology
In
Mining Engineering
By
SANJAY KUMAR
111MN0393
Under the guidance of
PROF. S. JAYANTHU
Department of Mining Engineering
National Institute of Technology Rourkela
2015
2. i
National Institute of Technology Rourkela
CERTIFICATE
This is certified that the thesis entitled “ANALYSIS OF SUBSIDENCE AND
STABILITY OF PILLARS IN A COAL MINE” submitted by Mr Sanjay Kumar, Roll
No. 111MN0393, in partial fulfilment of the requirement for the award of Bachelor of
Technology degree in Mining Engineering at the National Institute of Technology, Rourkela
(Deemed university) is an authentic work carried out by him under my supervision and
guidance.
To the best of my knowledge, the matter embodied in the thesis has not been
summited to any university/institute for the award of any degree or diploma.
DATE -
Place - Rourkela
Prof. S. Jayanthu
Department Of Mining Engineering
National Institute Of Technology
Rourkela-769008
3. ii
ACKNOWLEDGEMENT
I wish to express my sincere gratitude towards my project guide Prof. S. Jayanthu,
Department of Mining Engineering, National Institute of Technology Rourkela for providing
me with this opportunity to work under him and guiding, supporting and motivating me
throughout this project.
I want to thank Mr. P. N. Mallick, as he helped me a lot with the project requirements.
For letting me work with his consent, in the sophisticated laboratories of the Department of
Mining Engineering, I want to thank Prof. M.K .Mishra.
Sincere thanks to Mr. R.K. SINHA, Mine Manager, Kumda Mines, Bishrampur, Chattisgarh
for helping me with the basics of mining.
I would also like to thank the Department of Mining Engineering, National Institute of
Technology Rourkela for letting me with everything.
I would also like to thank my friends and seniors who helped me out in clearing some of the
conceptual doubts I had.
SANJAY KUMAR
111MN0393
Department Of Mining Engineering
National Institute Of Technology
Rourkela-769008
4. iii
CONTENTS
Certificate………………………………………………………………………………………i
Acknowledgement…………………………………………………………………………….ii
Contents………………………………………………………………………………………iii
Abstract……………………………………………………………………………………….iv
List of Tables………………………………………………………………………………….v
List of Figures………………………………………………………………………………..vi
Chapter 1 – Introduction………………………………………………………………………1
1.1 Objective…………………………………………………………………………..2
1.2 Methodology………………………………………………………………………3
Chapter 2 – Pillar Design……………………………………………………………………...4
2.1 Basic Principles of Pillar Design…………………………………………………..5
2.1.1 Estimating the pillar load using tributary area theory……….…………..6
2.1.2 Pillar Strength Formula………………………………………………….9
2.1.3 Pillar Safety Factor……………………………………………………..12
2.2 Types of Pillars…………………………………………………………………...12
2.3 Subsidence………………………………………………………………………..13
2.4 Technical Parameter of the Subsidence…………………………………………..13
2.5 Theory of Subsidence…………………………………………………………….15
2.5.1 Vertical and Normal Theories………………………………………….15
2.5.2 Beam and Plane Theory………………………………………………..16
2.5.3 Trough Theory………………………………………………………….16
2.5.4 Continuum Theory……………………………………………………..17
2.5.5 Particulate Theory……………………………………………………...17
2.5.6 Dome Theory…………………………………………………………...17
2.6 Subsidence Management…………………………………………………………18
Chapter 3 – Case Study………………………………………………………………………20
3.1 Description of SECL Mine……………………………………………………….21
3.2 Maximum Observed Subsidence…………………………………………………21
3.3 Shape of the Subsidence Trough…………………………………………………24
Chapter 4 – Geo-Mining Parameters…………………………………………………………29
4.1 Geo-Mining details of the Study Site…………………………………………….30
4.2 Physico Mechanical properties of Overlying Strata……………………………...32
4.3 Lithology of the Mine……………………………………………………………33
Chapter 5 – Empirical Model………………………………………………………………...35
Chapter 6 – Numerical Modelling……………………………………………………………39
6.1 Numerical Modelling Design…………………………...………………………..40
6.2 Stress Distribution over Pillars…………………………………………………...42
Chapter 7 – Results and Analysis…………………………………………………………….45
Chapter 8 – Conclusion………………………………………………………………………47
References……………………………………………………………………………………49
5. iv
ABSTRACT
The significance of mining will be certainly immense to human development. Truly,
as one of the biggest of human endeavours, Mining and its improvements relate
nearly with social progress. One of underground mining methods is the Bord and
Pillar Method of Mining and this method is one of the oldest Mining Methods. By
the help of Bord and Pillar Mining, extraction will be high. The key to successful
Bord and Pillar Mining is selecting the optimum pillar size and stability of the pillar.
If the pillars are too small the mine will collapse. If the pillars are too large then
significant quantities of valuable material will be left behind reducing the profitability
of the mine. The issues relating to the stability of pillars and Subsidence from it will
be a major concern now-a-days. The most critical parameter before outlining and
stability of pillars will be the Safety component.
The primary objective of this project is to increase the extraction proportion with the
help of stability of created pillars and subsidence control and Based on laboratory testing
of coal samples, empirical and numerical modelling studies related to the stability of the
pillar and analysis of observation data on subsidence profiles for underground coal mine, the
following conclusions are done. Field observations at Kumda underground mine indicated
stability of the pillars without any perceptible side spilling and crushing. Uniaxial
compressive strength, triaxial testing of coal samples indicated UCS, cohesion(C) and
internal friction angle(∅) of 27.9 MPa, 1.85 MPa and 300
respectively. Empirical and
numerical modelling using two dimensional continuum analyses indicated the maximum
stress of 5 MPa over the pillar and safety factor exceeding 2 confirming to the qualitative
observation of stability of the pillar. Maximum subsidence at 1.58 m was observed over the
over the extracted panels with a subsidence factor of 0.63 for the depillaring panels with the
width and depth of 64 m-14 m, 30 m-45.5 m respectively.
6. v
LIST OF TABLES
TABLE NO NAME OF TABLE PAGE NO.
1 Maximum Subsidence Observed at the Short Wall Panels 23
2 Geo-Mining Parameter of Balrampur 10 and 12 mine 30
3
Geo-mining Parameters of developed workings under 15 m
depth cover
32
4
The borehole details lying over developed workings under 15
m depth cover at the Balrampur Mine
33
5
Representative Lithology above the Pasang seam along with
their intact properties
33
6 Parameters used in the Numerical Modeling 40
7. vi
LIST OF FIGURES
FIGURE NO. FIGURES PAGE NO
1 Pillar Design 6
1.(a”) Surface Subsidence 23
1. (a)
Subsidence Profile Across The Panel 84m Panel
Width And 60l Short Wall
24
1. (b)
Subsidence Profile Across The Panel
104m Panel Width And 34l Short Wall
25
1. (c)
Subsidence Profile Across The Panel Centre Line At
63m Short Wall Panel
26
1. (d) Subsidence Vs Time Curve 27
1. (e) Subsidence Vs Distance 27
1. (f)
Subsidence Vs Distance From The Curve Of A
Particular Point
28
2.
Typical Section of Borehole at Balrampur 10 and 12
Mine
31
3.
Grid Generation for Development of Galleries and
Pillars in the Seams
41
4. Stress Distribution Over Pillar After Development 42
5. Stress Distribution Over Pillar/Stook 43
9. 2
1.0 INTRODUCTION
Mining is one of the most important sectors for the continuous development or growth of any
nation. Mining is the economic extraction of valuable minerals like coal, iron talc, zinc,
uranium etc. from earth for many purposes like generating electricity, pharmaceutical
applications, infrastructures, cosmetic cream, etc. It provided a base for the civilization to
grow in all its form and acted as an example for the other sector of industries to breed.
Mining can be done in two ways, underground and open cast. Underground mining broadly
consists of two types, a) Long wall method and b) Bord & Pillar method. The latter is
predominantly followed in India compared to the former. Most of the coal mining is done by
the Bord and Pillars Method.
1.1 Objective
Stability analysis of subsidence in coal mine and Study of strength of the pillar, stress
distribution over the pillar through empirical and numerical modelling.
10. 3
1.2 Methodology
The methodology of the project was described in a flow chart format below:
Literature review of different materials
available
Field visit was done
Subsidence and stability of pillar was
analysed
Experiment and data collection is carried
out
Result and Conclusion
12. 5
2.1 Basic Principle of Pillar Design
Basic Principle of Pillar Design Pillars are the natural structural member of a coal mine to
support the roof and to assist in transferring the overburden load to floor for wider area
dissipation. An optimum dimension/design ensures minimum coal being blocked in the pillar
while maintain its stability. Nevertheless it continues to experience stresses throughout its life
or till failure occurs. Pillar loading is of three types: preliminary loading or loading
immediately following excavation of opening; subsequent loading or the abutment pressures
(i.e. after a portion of coal has been extracted, the roof beds are detached and the beds above
are relieved of the weight of the higher strata and the load which was originally acting
vertically over the excavated area then deflects and bridges over the working area and
transmits its weight forward to some region ahead of the coal face known as “front abutment”
and backward behind the coal face at a region where the strata again make contact by
subsidence of the higher beds known as “back abutment”) and progressive failure theory for
post-mining loading. The “classic” methods consisted of three steps:
i. Estimating the pillar load using tributary area theory.
ii. Estimating the pillar strength using a pillar strength formula.
iii. Calculating the pillar safety factor.
13. 6
Figure (1) Pillar Design
2.1.1 Estimating the pillar load using tributary area theory
Estimating the load was fairly straight forward for an industry that relied almost exclusively
on room-and-pillar mining at relatively shallow depth. The tributary area estimate was
considered sufficient, though it was recognized that in narrow panels the pillars near the
edges might not experience the full load. More complex were the issues associated with pillar
strength. The two big issues were the “size effect” and the “shape effect.” According to this
concept, a pillar takes the weight of overlying rock up to a distance of half the opening width
surrounding it. The theory assumes that each pillar carries a proportionate share of the full
overburden load.
14. 7
In the figure, Wo and Wp are widths of the opening and pillar respectively, while Lp is the
length of the pillar. For square pillars, Wp= Lp
The load on the pillar, is P = (Lp + Wo) × (Wp + Wo) × γ × g × h
Where γ*g is the weight of the rock per unit volume, and h is the depth of mining.
The stress on the pillar σp= =
( ) × ( ) × × ×
( )
=
( ) × ( ) ×
( )
In case of inclined seams the formula for stress on the pillar is
σp =
( ) × ( ) ×
( )
× ( Ɵ + Ɵ)
Where, θ = angle of inclination,
m = Poisson’s ratio, and
σv = vertical stress = γgh
The above equations indicate that the factors influencing pillar load are:
Depth – the deeper the mining, the higher the load,
Pillar width – the smaller the pillar, the higher the load,
Bord width – the wider the bord, the higher the load,
Extraction ratio- The higher the extraction, the higher the pillar load.
15. 8
2.1.1.1 Limitations of the tributary area theory
1. Average pillar stress is calculated by assuming that pillars uniformly support the
entire load overlying both the pillars and the mined-out areas.
2. Tributary area theory assumes regular geometry and ignores the presence of
abutments. The effect of deformation and failure in the roof strata resulting from the
mining operation are disregarded.
3. The concept does not take into account abutment stress distributions and deformation
or failure of the pillar. Also, if there is displacement interaction between the
surrounding strata and the pillar itself, stress may be redistributed within the system,
resulting in a stress state significantly different to the theoretical state.
4. The average pillar stress is purely a convenient quantity representing the state of
loading of a pillar in a direction parallel to the principal direction of confinement. It is
not simply or readily related to the state of stress in a pillar that could be determined
by a complete analysis of stress. The implicit assumption that the other components of
the pre-mining stress field have no effect on pillar performance is not generally
tenable. Furthermore the tributary area theory ignores the effect of the location of the
pillar within a mine panel (Brady and Brown, 1993).
5. The tributary area theory is only valid for cases where the width of the panel is as
great as or greater than the depth and where the pillars in a panel are of the same size.
Other factors that have been found to influence the validity of the tributary area theory
include the percentage extraction and the stiffness of the overburden (Van der Merwe,
1998).
16. 9
2.1.2 Pillar Strength Formula
Numerous pillar strength formulas have been proposed, but five formulas are used most
commonly (Bieniawski, 1984; Peng, 1986). Each formula specifies its own appropriate factor
of safety. These are given below:
2.1.2.1 Obert-Duvall Approach (Obert and Duvall, 1967)
It was derived from laboratory tests on hard rock and elasticity considerations the same
relationship as did Bunting (1911). Greenwald et al. (1939) mention that this form of an
expression for pillar strength was proposed in 1900 for anthracite after laboratory tests made
for the Scranton Engineers Club. This formula is given as
σp = σ1(0.778 + 0.222 ×
W
H
)
Where, σp is pillar strength,
σ1 is uniaxial compressive strength of a cubical specimen (w/h = 1),
and w and h are pillar dimensions in meters.
According to Obert and Duvall, this equation is valid for w/h ratios of 0.25 to 4.0, assuming
gravity-loading conditions. Through back calculations from mining case histories and
utilization of laboratory rock properties, safety factors of 2 to 4 were derived for short- and
long-term pillar stability, respectively.
2.1.2.2 Central Mining Research Institute approach (now CIMFR, India)
Formula for pillar strength taking into account the pillar w/h ratio, the uniaxial compressive
strength of the pillar, the height of seam and depth of cover. The developed equation is
nothing but a reflection of the triaxial state of different stresses involved. It is given by:
S = (0.27 × σc × h . ) + [
H
160
× (
W
H
− 1)]
Where, S = Pillar strength (in MPa),
17. 10
σc = Uniaxial compressive strength, UCS ( in MPa)
h = Working height or seam height (in m)
H = Depth of cover (in m) w = Pillar width (in m)
2.1.2.3 Bieniawski approach (1968, 1969)
This approach is based on large-scale in situ tests on coal pillars. Such tests were first
undertaken in the United States by Greenwald et al. (1939) during the period 1933–1941.
Extensive tests were conducted in South Africa during 1965–1973 by Bieniawski (1968,
1969), Wagner (1974), and Bieniawski and van Heerden (1975). Wang et al. (1977)
conducted in the United States the largest test of all involving one full-sized coal pillar
measuring 80 ft. (24 m) in width. All these investigations examined the various pillar-
strength formulas
The general normalize form of the Bieniawski equation is σp = σ1(0.64 + 0.36w/h ) Where
σp is pillar strength, w is pillar width (m), h is pillar height (m), and σ1 is the strength of a
cubical specimen of critical size or greater (e.g., about 3 ft. or 1 m for coal)
2.1.2.4 Holland & Gaddy approach
They extended the work by Gaddy (1956) and proposed the following formula:
σp = k(
√W
h
)
Where, k is the Gaddy factor,
w and h are pillar dimensions in in.,
σp is pillar strength in psi.
18. 11
Holland specified a safety factor between 1.8 and 2.2 for the design of coal pillars, with a
suggested value of 2.0. The width-to height ratio, for which the Holland formula is valid,
ranges from 2 to 8. Although popular in the 1970s, the Holland-Gaddy formula is no longer
recommended because it was found to be overly conservative at higher ratios (> 5).
2.1.2.5 Salamon and Munro (1967)
They conducted a survey of failed and standing coal pillars in South Africa. Based on the
studies of Holland (1964) and Greenwald et al. (1939), they selected the following form of
pillar strength to apply to square pillars
Strength = k × h × w
The constants for the above equation were derived from a statistical survey of data reflecting
actual mining experience. In all, 125 case histories were used, of which 98 were standing
pillars and 27 were failed pillars (collapsed at the time of the analysis). In deriving a pillar
strength formula, it was assumed that those pillars that were still intact had safe dimensions,
while the collapsed pillars were too small.
The following pillar strength formula was proposed:
= 1.32 × w .
/h .
Where, σp the strength is in psi,
And the pillar dimensions, w and h are in feet.
The recommended safety factor for this formula is 1.6, the range being 1.31 to 1.88.
In si unit pillar equation becomes
19. 12
σp = 7.2 × w .
/h .
Where, σp the strength is in MPa while w and h are in meters.
2.1.3 Pillar Safety Factor
Factor of Safety (SF) is the ratio of strength of pillar and stress on pillar.
FOS =
Where σp = strength of pillar and Sp= stress on pillar the above approach of pillar design
incorporates the following assumptions:
The seam is subjected only to vertical pressure, which is constant over the mined area.
However, stress transfer occurs where stiff abutments exist in underground workings.
Thus this vertical pressure may be relieved partially.
Each pillar supports the column of rock over an area that is the sum of the cross-
sectional area of the pillar plus a portion of the room area, the latter being equally
shared by all neighbouring pillars. However, this is certainly not valid if the area of
development is small since the pillars in the centre of the excavation are under more
stress than the pillars close to the sides. It is usually only accepted as valid if the mined-
out area is greater than the depth below surface.
It is assumed that the load is uniformly distributed over the cross-sectional area of the
pillar
20. 13
2.2 Type of Pillars
Based on the W/H ratio, coal pillars are divided into three categories:
Slender pillar: pillars which have W/H ratio less than 3 or 4. When these pillars are
loaded to their max. Capacity, they fail completely, shedding nearly their entire load.
Intermediate pillar: pillars which have W/H ratio in the range of 4-8. These pillars
neither shed their entire load when they fail nor can accept any more load.
Square pillar: pillars which have W/H ratio greater than 10. These pillars can carry
very large loads.
2.3 Subsidence
Mining subsidence is manifestation of the action of gravity on strata which have been
rendered unstable by the withdrawal of their natural support over a sufficiently large area.in
such cases all the strata from the seam to the surface sink slowly at different rates, until in the
course of time with the development at opposing forces equilibrium is restored at the lower
level.
2.4 Technical Parameters of Subsidence
a) Angle of Fracture/Crack
Underground coal extraction causes subsidence movement in the form of trough and cracks
on the surface. The strata between surface and coal extraction have been subjected to
intensive fracturing and dilation of discontinuities. In the panels, first time subsidence
induced cracks appeared along with formation of trough on the surface and during the first
main fall. The outer ring of the cracks formed on the surface during first main fall was almost
circular in shape. The diameter of the outer ring of the cracks was about 40m and lies in
Centre of the panel between 10m retreat to 50m retreats in the short wall panels. After further
21. 14
advance of the face and subsequent falls in the goaf the subsidence cracks reached above the
barrier of the panel and front cracks reached up to 5-30m behind the face on the surface. It
depends on major fall interval, surface blasting (position, time and blasting geometry) and
rock mass characteristics. The cracks becoming widened and extended gradually up to
350mm in convex portion and were again closed down due to compressive forces in concave
portion of the trough. It was experienced that for better strata management in the panel, the
fronts cracks should not be lies far behind from the face and it should be lies between 5m to
20m in ideal condition. Generally cracks were found 5-6 m behind face line and so the angle
of crack was (-) 050
56’ 48’’ in longitude direction. In transverse direction angle of fracture
was observed between (-) 10
47’ and (+) 210
48’.
b) Slope of the Ground
Differential vertical subsidence between adjoining points along the surface of the subsidence
trough will form a slope and induce tilting. The slope is expressed by the derivative of the
vertical subsidence with respect to the horizontal. When the ground subside slopes (tilts) are
induced. The maximum tilt occurs at point of inflection (where half of the maximum
subsidence occurs) which is about 20-25 away from the barrier on transverse line and
between panel edge and the Centre line. The maximum slopes of the ground surface were
computed as 47mm/m to 109mm/m on longitudinal and transverse lines over the panels.
C) Strain of the Ground
Vertical displacement can be obtained by taking the first derivative of the slope or the second
derivate of the vertical subsidence with respect to the horizontal. The value of vertical
curvature can be expressed by the radius of curvature i.e. the reciprocal of the curvature.
Where a curve is induced in the ground surface, it will either stretch or compress the surface
22. 15
depending on whether the curve is convex or concave. Near the edge of the profile, the shape
is convex and a tensile strain develops, manifesting itself as an open crack or a zone of
cracks. In the Centre of the trough, where the shape is concave a compressive strain develops.
This may lead to small ridges being created. These are some time difficult to find being a few
millimeters high. The maximum compressive strain of the ground was in the range of
29mm/m to 69 mm/m and the maximum tensile strain was in the range of 28mm/m to
66mm/m in the ground over the panels at the mine.
However, DGMS guidelines for maximum surface strain is 1.5 mm/m for important buildings
and plants, 3 mm/m for main railways lines, road, rivers, water tanks and only for small
buildings and branch railway lines they permit a strain of 6mm/m so it is statutory obligation
to plan the mining activity accordingly.
d) Angle of Draw
The angle of draw is the angle between a vertical line from the edge of the workings and a
line to the point at which the subsidence becomes negligible. The surface area laying outside
the zone of draw will not be affected by the workings. Therefore the angle of draw defines
the limit of subsidence and is also called the limit angle. The field observations indicate that
measurable surface movement does not extend outside a zone bounded by a (+) 200
8’ limit
angle in the mine. The average angle of draw for the areas containing all short wall panels is
100
.
2.5 Theories of Subsidence
Some of the old and modern theories of subsidence have been briefly described here
23. 16
2.5.1 Vertical and Normal Theories
According to dome theory it is believed that the rocks overlying an excavation are acted on
by two forces cohesion and gravity only. If the gravity overcomes under cohesion, the roof
will fall forming an enlarging arch. Subsidence will take place only if the dome breaks
through to the surface. The axis of dome is vertical when seams are horizontal, but it lies
between normal and vertical when seams are inclined.
2.5.2 Beam and Plane Theory
The immediate roof to be a cantilever beam and considered that the lowest part would be
under compression and upper part under tension. The break in immediate roof occurs. The
theory has been improved by considering the beam built in at both ends and loaded by its
own weight.it is assumed that no bond exists between the layers and thus they are free to
deflect independently.
2.5.3 Trough Theory
Distinguish between a main break and an after break. In flat seams the main break is vertical
and the after break is in a direction bisecting the vertical and the angle of slide.in dipping
seam the angle of draw increases.it is 35.8 degree from the vertical for a 40 degree dip and
the main break occur over the seam at an angle from the vertical equal to the half the dip
and the angle of draw and the angle of slide are the main factors used to determine the extent
of subsidence. The angle of slide ∝ can be protected on the basis of coulomb’s theory and is
given by
∝=45+∅/2
Where, ∅ is the angle of internal friction of the material.
24. 17
2.5.4 Continuum Theory
In continuum theory it is assumed that the ground acts as a continuous body bounded by the
surface above and the excavation below. If the elastic moduli, the initial stress in the ground
and the boundary conditions that is the distribution of stress on surface, on the roof or on the
floor are given i9t is possible to predict stress and placements at any point of the medium by
using the theory of elasticity (salamon 1994).
2.5.5 Particulate Theory
The rock medium for which stochastic equation determines movement has been called a
stochastic medium. The concept upon which the theory of stochastic media is based is not
restricted in application to loose media only.it can be used in explaining subsidence in
continuous media also.
2.5.6 Dome Theory
The fracture extends vertically to the surface from the boundaries of the underground
excavation. later this view evolved into normal theory according to which it was assumed that
the strata subside normal to the seam.it was suggested that the subsidence; limits varied from
vertical to the normal depending upon rock sequence and limiting lines bisect the angle
between the vertical and normal lines when the dip is less than 45 degree and the dip exceed
45 degree the of fracture lies at an angle 45 minus half the angle of dip.
2.6 Subsidence Management
The subsidence induced cracks generated due to extraction of coal in underground panels
should be filled in immediately particularly during rainy season. The width of the cracks is
varying from few mm to 350mm. In order to prevent the entry of water in the subsidence area
25. 18
over the work-outs/workings of short wall workings, the cracks developed were filled in and
compacted properly.
In shallow depth working, there may be a chance of pot-hole or abrupt subsidence
particularly in low lying area where overlying strata including hard cover got lower
competency or hardness due to long percolation of the surface water. Therefore, the low lying
surface area over the panels were filled up to the level of the nearby ground and compacted
properly to give the shape similar to the surrounding, to ameliorate the chance of inundation
from surface water. In the property where the depth of working is very low, adequate and
proper stiffness of supports in the advance gallery and a regular face advance should be
maintained to prevent pot-hole and consequent strata control problem in the workings for safe
and smooth operation of the short wall panel.
a) A garland drain around the panel over the barrier was made to drain out the accumulated
surface water from the subsided or depressed area to keep it free from surface water. The
cross section of garland drains was 1mx1m and smaller cross section drains were also
made to connect the garland drain with the lowest level of the subsided area to drain out
the accumulated. If required, the earthen dam of proper design was also built to arrest
inflow of surface water in the subsided area.
b) Constant monitoring/supervision of surface area during the monsoon period and during
heavy shower, one competent person with sufficient manpower were deployed round the
clock to monitor the discharge at the culverts and at major points where there is chance of
accumulation of water. The crack, which was opened during heavy shower, has to be
filled in properly to prevent entry of water through it and take precautionary measure to
prevent inundation of the mine workings from the surface water.
c) The blast holes, which were used for induced caving in the panels, were filled in properly
so that there is no chance of entry of water in the mine.
26. 19
d) Plantation for environmental management on the surface over the extracted short wall
panels were done to upgrade the environmental condition, to stabilize the area and
prevent soil erosion where manifestation of the underground extraction in the form of
subsidence, subsidence induced cracks, slope, displacement and strain due to formation of
subsidence trough were occurred. Some plantations are taken the shape the bushes and in
recent goaved out areas sapling has been grown to increase the green cover. Plantation of
local species considering requirement of fruits, timbers, and fodder has created an
atmosphere for conservation of faunal species in the subsided area.
28. 21
3.1 Description of the SECL Mine
The mine is located 9 km north from the Bishrampur railway station and 30 km northwest
from the district head quarter, Ambikapur (Surguja), Chhatisgarh. The topographical area
consists of undulated (both cultivated and baron) land. The elevation in the area ranges from
536 m to 560 m above MSL. The drainage of the area is controlled by seasonal Gour bahra
nullah flowing west east across the middle of the property. The nullah discharges in Pasang
River flowing outside the mine leasehold area.
The enclosing latitude and longitude of geological block are-
Latitude from 230 12' 16" to 230 15' 16" (N)
Longitude from 82058' 58" to 830 02' 53" (E)
The area is free from major geological disturbances.
3.2 Maximum Observed Subsidence
The maximum possible surface subsidence at a point on the surface occurs after a certain
minimum width of a seam has been extracted. This minimum width called critical width. The
thickness of the excavated seam affects the magnitude of surface subsidence. The thicker the
coal seam, the greater will be surface subsidence.
29. 22
Figure no- (1a”) Surface Subsidence
The maximum possible subsidence factor (A) for critical and supercritical widths depends on
the rock characteristics of the overburden strata, the method of mining and the roof control.
The subsidence factors define as;
=
Where, A = Subsidence factor,
S max = Maximum possible subsidence
M = Extracted seam height (m)
For the short wall caving method, properties of the overburden strata provide a major effect
on the variation in A. When the overlying rock is comparatively soft and weak, A is a large,
30. 23
whereas when the overlying rock is hard and strong, A is small. Table 3 shows the subsidence
factor observed in the worked-out panels.
Table (1): Maximum Subsidence Observed at the Short Wall Panels.
Given by the mine manager SECL
The subsidence factors for the panels are varying from 0.41 to 0.63 at the mine. The amount
of maximum observed subsidence in short wall panel is generally slightly more than the
maximum observed subsidence in the long wall panels at the mine and this may be due to the
Name of
the Short
wall Panels
Widths
of Panels
(M)
Av. Depths of
panels
(M)
Maximum
Subsidence
(CM)
Subsidence factor
63
(1
ST
Panel)
84 45.5 95 0.41
58L
(2
ND
Panel)
84 38 117 0.50
57L
(3RD
Panel)
84 35.5 127 0.55
34L
(4
TH
Panel)
104 32 111 0.48
S-7
(5
TH
Panel)
104 32 158 0.63
S-6
(6TH
Panel)
84 30 114 0.45
S-5
(7TH
Panel)
84 30 148 0.59
46L
(8TH
Panel) 64 41 116.5 0.47
31. 24
lesser depth of working in the short wall panels. The maximum observed subsidence in S-7
short wall panel was exceptionally high. Before commencement of extraction in this panel the
seasonal nallah flowing over the last portion of the panel, which was suitably diverted outside
and the overlying strata over the panel of his portion was soft and this may be the reason for
such high subsidence in a particular zone.
3.3 Shape of the Subsidence Trough
When a subsidence trough is formed at the surface, the central part subsides vertically and the
remainder moves inwards and downwards toward the Centre. Points located directly above
the Centre of the goaf will subsides vertically and be displaced on an axis parallel to the goaf,
where points away from the Centre will be displaced in an elliptical fashion. Since the Centre
point is not moving horizontally, while the points on either side of it move inwards toward it,
the central part of the subsidence trough will be subjected to lateral compression. In the
Centre of the excavation, the vertical subsidence is maximum whereas the horizontal
displacement is zero.
Fig. 1(a): Subsidence profile across the Panel, 84m panel width, 63L Short wall Panel
32. 25
0
20
40
60
80
100
120
-5 0 5 10 15 20 25
30
35 40 45 50 55 60 65 70 75 80 85 90 95 100 105
Distance from the Main Gate (M)
Subsidence (CM)
Main Gate Tail Gate
The rock is so variable in nature and its geometry that there was often a difference between
profiles on the same mine. Fig. 1(a), Fig. 1(b) and Fig. 1(c) depicts the subsidence profiles
over the panels in across and along the panel at the mine
Fig. 1 (b): Subsidence Profile across the Panel, 104m panel width, 34L short wall Panel
The subsidence profile has a part which is convex and where the ground surface is getting
elongated and another part is concave where the elongated ground surface is getting
compressed. Thus, over the advancing face and the nearby goaf where ground tilt was
occurring tensile strain develops. The maximum tensile strain develops where the angle of
break reaches the ground surface from the edge of the solid face. Further on the goaf side the
shape of the subsidence profile changes to concave and the particles on the ground now
comes nearer to each other giving rise to compressive strain.
After the ground tilt has been fully recovered in an extraction of supercritical width the
subsidence profile takes the shape as in the original ground and there is neither tensile nor
compressive strain at the central part of the subsidence trough. It was also observed that due
33. 26
to induced blasting, slope of the subsidence profile increased i.e. full subsidence reached on
surface quicker.
Fig. 1 (c): Subsidence profile along the panel Centre line at 63L Short wall Panel
Subsidence was not reaching on surface instantaneously. The major surface subsidence was
achieving in 6-9 days i.e. after an advance of the face about 54 to 61m. The rate of
subsidence at a particular point depends on the rate of face advance, location of points at the
grids and depth of workings. Subsidence as a function of time and distance from face is
illustrated in Fig. 1(d), Fig. 1(e) and Fig. 1(f).
It was found that the first settlement of the ground which constitutes about 1-9 % of total
subsidence takes around 2-4 days’ time or at an advance of about 12-24m and was occurred
in steady stage. In the accelerated settlement, around 5-26% of the total subsidence occurred
and it takes another 2-4 days i.e. a further about 10-25m advance of the face. Major
subsidence occurred in the rapid settlement stage and it constitutes about 50-90% of the total
subsidence, and it takes 1-3 days i.e. further advance of 3-15m. During final settlement
periods negligible change in subsidence occurred. The magnitudes of the residual subsidence
after the extraction of the panel was measured and it was found that at stations 57L/60C and
58L/310C was 4.08% and 6.45% of the total subsidence observed respectively and total
34. 27
stabilization of ground was taken place after elapsed of 12 months from completion of
extraction of the panel.
Fig. 1 (d): Subsidence Vs time curve of a particular point (30m/S-7) over the short wall
panel.
Fig. 1 (e): Subsidence Vs distance from the face curve of a particular point (130m/57L)
over the short wall panel
37. 30
4.1 Geo-mining Details of the Study Site:
Profundity of hard cover of Pasang crease working of Balrampur 10 and 12 mine, SECL in
the ascent side were under 15 m at numerous spots having four-path intersections with
section measure 4.5 x 2.8m with columns 20m x 20m . Different geo mining parameters of
the mine are as per the following:
Table (2): Geo Mining Parameters of Balrampur 10 and 12 mine
Thickness of the seam 1.8 to 2.7 m
Gallery size : : 45×2.7 m
Height of the exhibition 2.4 to 2.7 m
Pillar size 20 m X 20 m
Depth of working 21 m to 44 m (Hard cover is under 15 m)
Nature of rooftop & floor Shaley Sandstone
Nature of rooftop & floor 1 in 51
RMR 56.3
Modulus of elasticity 1.8 Gpa
Tensile strength 3.11 Mpa
Compressive quality of coal (M Pa) 27.9
Density of coal(kg/m3) 1400
Fig. 2 shows bore opening segment of BXI 15 of Balrampur, and CBBP-111,112 &113 of
Kumda 7&8 Inclines, individually. Top Soil thickness shifted from 2 m to 5 m here while
weathered mantle differed from 8 m to 12 m. hard cover in these areas was discovered to be
around 6.2 to 15 m.
38. 31
Fig. 2: Typical section of bore hole a Balrampur 10 and 12 mine, SE
Soil and sandstone section assumes a critical part on stacking design of the hidden strata. It
for the most part grants dead load on the fundamental beds of the strata. Next fundamental
section is sandstone whose lattice changes from coarse grain to fine grained and the other
way around. Coarse grained sandstone is by and large of low RQD though fine grained
sandstone is of high RQD and quality.
The prompt rooftop over the coal crease comprises of shally coal, carbonaceous shale, and
dim shale having thickness of 21 cm to 41 cm. The significant bit of prompt rooftop
comprises obviously grained to fine grained sand stone with a compressive quality of around
17.5 MPa. The compressive strength of coal seam is 27.9 MPa
The geo-mining parameters of the proposed study area of the Balrampur and Kumda mines
are shown in Table 1. Field observations during February’15 and detailed measurement of
width and height of workings and pillar dimensions through offset survey revealed that the
gallery width in majority of the cases is within 4.8 m, except at the loading points with about
39. 32
5.5 m gallery width and height of 2.9 m at an interval of about 2-3 pillars distance in the
conveyor roadway. However, there was no spalling of pillar sides and roof disturbances
indicating stability of the roadways and pillar in the present condition of no roof support in
the developed areas. Travelling roadways were supported by roof bolting.
4.2 Physio-Mechanical Properties Of Over Laying Strata
Various boreholes had been drilled over concerned panels i.e. 18L of Balrampur 10 & 12
Inclines mine and 29L district of Kumda 7&8 inclines mine. The hard cover along with the
depth and thickness of the seam are given in Table 2.
Table 3: Geo-mining Parameters of developed workings under 15 m depth cover
Height of gallery: 2.4 m- 2.7 m
Depth of concerned developed panels: 21 to 44 m
Hard cover 6.2 m to 15 m
Existing overlying/underlying workout areas Nil
Existing mining pattern Developed on bord & pillar workings
Pillar size: 20 m x 20 m (center to center)
Gallery width: 4 m - 4.8 m
The average hard cover in the concerned area is less than 15m and the depths of the seam
were from 20m- 33m. Based on engineering judgment and giving a higher weightage to the
borehole lithology, estimated RQD and the intact average compressive and tensile strengths
of different beds tested in the laboratory are given in the Table 4.
40. 33
Table 4: The borehole details lying over developed workings under 15 m depth cover at
the Balrampur mine
Borehole no.
Depth of cover,
(m)
Seam thickness,
(m)
Hard cover, m
BIX-15 (18L district) 21.23 2.27 6.20
CBBP 113(29L) 44.00 1.10 15.00
4.3 Lithology of the Mine
Table 5: Representative lithology above the Pasang seam along with their intact properties
Bed No.
Run up
wards, m
Rock types
Thick-
ness, m
RQD
%
Compressive
Strength,
Mpa
Tensile
strength,
MPa
Coal 2.4 -- 23.8 2.5
Bed-I 0.0-5.51
Medium grained
sandstone,
laminated with
shale
5.51 40 10.96 1.5
Bed-II 5.51-12.17
Coarse grained to
medium grained
sand stone
6.66 78 17.1 1.4
Bed-III 12.17-16.02
Very coarse
grained sand stone
3.85 43 13.92 1.4
Bed-IV 16.02-30.00
Medium grained
sand stone
13.98 75 14.5 2.2
Bed-V 30.00-41.00 Weathered rock 11.00 -- -- --
Bed-VI 41.00-50.00 Sandy soil 9.00 -- -- --
The thickness and RQD of the six major overlying beds for these four boreholes are given in
Table-5. Similar to the observations of the previous boreholes in this mine, it is observed that
Bed-2 and Bed-4 are the massive beds with high RQD and are responsible for the weighting
intensity at the faces.
41. 34
As per the numerical modeling studies carried out earlier (CIMFR Report No. GC/MT/47/99-
2000), for a face length of 84m with a depth of cover of 50m consisting of 30m hard cover
and 20m weathered rock, the main fall was predicted to occur between 110 to 120m of the
face advance. The actual observed main fall span was 120m.
The borehole BIX-117 is at the start of the 58L short wall panel where the hard cover was
25.17m and the depth of cover was 41.97m. As per CIMFR Report No. GC/MT/47/99-2000,
for a face length of 84m, cover depth of 40m consisting of 20m of hard cover and 20m of
weathered rock/alluvial soil, the main fall was predicted to occur between 100 m to 110m of
face advance. The actual observed main fall span was 96m.
Thickness of hard cover and soil+ weathered rock decreases. From the observations of
numerical models (Refer CIMFR Report No. GC/MT/47/99-2000), the main fall span
increases with the increase in the hard cover thickness, decreases with the increase in the
thickness of soil+ weathered rock Based on the above analysis it is observed that as the depth
of the cover decreases the and also decreases with the decrease in the cover depth. Further, as
the face span increases from 84 m to 104 m, the main fall span for depth of cover of 50m
consisting of 30m hard cover and 20m weathered rock decreases from 110-120m to 90-100m
which correspond to a decrease of 16% to 17%.
Overburden Dump of 8.2 to 12 m height along with Arshota nalah is available over N2 panel
of Kumda 7 & 8 m under 37 m depth cover. From the surface contours it is evident that the
developed workings are at a depth of 27 m under the nalah.
43. 36
5.0 EMPIRICAL MODEL
Stability of the pillars was evaluated with the conditions of 4 locations; 18 L district, S1 panel
of Balrampur mine, 29 Level districts and N2 panel at Kumda mine of the study sites. The
safety factor of pillars is calculated as the ratio of the pillar strength and the average pillar
stress. The strength of the pillar is calculated using CMRI pillar strength – empirical
equation.
Uni-axial compressive strength tests were conducted and for estimation of pillar strength the
compressive strength of 25.4 mm cube sample σc was found to be 27.9 MPa. Mean density of
the overlying strata was estimated considering the variation in density of hard cover, soil,
weathered mantle and also in a typical site the 10 m high overburden dump. Pillar strength,
Stress on pillar and safety factor was estimated for three locations with depth cover of 21.23
m, 23.9 m, and 44 m considering the concerned borehole sections and the field observations:
Location 1: 18 L District:
Depth of cover H: 21.23m, Height of gallery w: 2.7m, Width of gallery h: 4.8m,
Strength of pillar S = 0.27 × 27.9 × 2.7 .
+ (
.
+ 1) × (
.
.
− 1)
= 6.1093 MPa
Stress on pillar = × (1 + ) where, r = unit weight of rock per meter,
z= depth of cover (m)
=2.6 x 10 x 103
x 21.13 (1 +
.
.
)
= 0.955 MPa
Factor of Safety: =
.
.
= .
44. 37
Location 2: S1 Panel:
Depth of cover H: 23.9m, Height of gallery w: 2.7m, Width of gallery h: 4.8m
Strength of pillar S = 0.27 x 27.9 x 2.7-0.36
+ (
.
+1) x (
.
.
-1)
= 6.116 MPa
Stress on pillar = 2.6 x 10 x 103
x 23.9 (1+
.
.
)2
= 1.076 MPa
Factor of safety: Strength/stress
= 6.116/1.076 = 5.684
Location 3: 29 L District: Depth of cover H: 44m, Height of gallery w: 2.7m, Width of
gallery h: 4.8m
Strength of pillar S = 0.27 x 27.9 x 2.7-0.36
+ ( +1) x (
.
.
-1)
= 6.179 MPa
Stress on pillar: = 2.6 x 10 x 103
x 44 (1 +
.
.
)
= 1.981 MPa
Factor of safety: Strength/stress
= 6.1795/1.981 = 3.1193
Location 4: N2 panel: Depth of cover H: 44m, Height of gallery w: 2.7m, Width of
gallery h: 4.8m
Strength of pillar S = 0.27 x 27.9x2.7-0.36
+ ( +1) x (
.
.
-1)
= 6.179 MPa
Stress on pillar: = 2.6 x 10 x 103
x 44 (1 +
.
.
)
= 1.981MPa
Factor of safety: Strength/stress = 6.1795/1.981= 3.1193
45. 38
Based on the above analysis, the factor of safety estimated through empirical models is in the
range of 3.1 to 6.4 indicating long term stability.
47. 40
6.1 Numerical Modeling Design
The elements in the panel considered are small. The elements are of size 1 m vertically and 1
m horizontally in the pillars. The dimensions of mesh elements increase geometrically from
the inner model to the outer boundary. This is done because accurate reading over the seam is
only required. Varying mesh size also reduces the simulation and computation time of model
as the elements at the boundary were of greater dimension. The development model is then
modified into an excavation model. Mohr Coulomb criteria and plain strain condition are
used for simulation of the model. The sandstone element was used as the depth covers and
the floor material. Table 6 shows Parameters used in the Numerical Modeling.
Table 6: Parameters used in the Numerical Modeling
Property Coal Sandstone Clay Band
Bulk Modulus 3.67 GPa 6.67 GPa 2 GPa
Shear Modulus 2.2 GPa 4.0 GPa 1.4 GPa
Density 1480 kg/m3
2100 kg/m3
1650kg/m3
Tensile Strength 1.86 MPa 9.0 MPa 6000 Pa
Cohesion 1.85 MPa 6.75 MPa 5000 Pa
Friction Angle 300
450
170
The top edge of the model is unconstrained and allowed to move in any direction. The side
edges of the model are constrained to move in x direction and left free to move in y direction.
The bottom edge of the model is constrained in moving in y direction that is vertically. The
in-situ vertical and horizontal stresses were calculated:
Vertical stress = ρ x H
Horizontal stress = 3.75 + 0.015 H
48. 41
Where, ρ = specific gravity of the rock mass cover and H = depth of cover.
The model is simulated to generate the in-situ stresses, before adding the mine openings or
galleries to the model. Then the mine opening or galleries required are added to the model.
After this the simulation is re-simulated to give the final stress distribution.
The 3 pillars have been modeled using FLAC5.0 with 4 galleries. The galleries are simulated
to plot their vertical displacement and vertical stress contours over pillars. It shows different
stages of a depillaring process. The different stages include division of pillars, splitting, and
extraction of the stooks so formed leaving just ribs in the goaf. The sequence of Numerical
modeling includes the following stages Fig 3 illustrates Grid Generation for Galleries and
pillars are developed in the seams.
In the present numerical model studies, geo mining conditions of Kumda 7&8 inclines and
Balrampur 10 & 12 inclines were simulated to understand the stability of pillars for hard
cover varying from 12m to 15 m.
Fig 3: Grid Generation for Development of Galleries and Pillars in the Seams
49. 42
6.2 Stress Distribution over Pillars
Cumulative stress over the pillars and stooks for FLAC simulation of numerical modeling for
different stages is shown. The model was simulated with roof support, roof and side support
and without support to comprehend the stress distribution over the pillars and stooks.
Maximum stress of 9 MPa is experienced by the stook present next to the fourth gallery after
excavation of 5 stooks. The maximum over the pillar remains more or less same for
supported and unsupported roof because the rock load remains constant. But the stress
distribution profile changes showing more stress enforcement at the side of the pillars for
supported roof and sides. Fig. 4 illustrates Stress Distribution over Pillar and stooks at
different stages of depillaring.
Fig. 4: Stress distribution over the fourth gallery
Stress distribution over the fourth gallery is shown in the Fig 16. The X-axis represents the
stress in MPa and Y-axis represents the goaf edge distance in meters. The maximum stress
distribution over the pillar/stook shows increasing trend because of load on the pillar/stook
due to extraction of adjoining stooks. The maximum stress observed from modeling was 9
50. 43
MPa. Critical spans for first breakage of different beds are computed on the basis of the
empirical-cum-statistical norms developed for long wall. Maximum span for first breakage of
the beds without presence of any ribs in the goaf has been found to be about 49 m. Roof
caving span was also ascertained for different depillaring panels in Indian geo mining
conditions on the basis of Q system of rock mass classification through the parameters: =
factor depending on rectangularity b/a of the plate, a= smaller plate dimension, and b = larger
plate dimension. When b/a <3, the equivalent face advance aeq can be found as aeq = a for
an infinitely long face when fall would occur.
Fig. 5: Stress Distribution over Pillar/Stook
In the light of the plate theory and considering the rectangularity of the depillaring panel, the
corresponding span for first breakage of the roof is ascertained to be 58 m. therefore,
considering the above two approaches, first major fall without presence of any ribs can be
anticipated at 50 to 60 m clear span in the goaf. Numerical analysis was also conducted to
assess the influence of ribs which are generally left in the goaf. To study the influence of
maximum possible size of ribs in the proposed extraction on goaf settlement, stability of 2.0
m wide ribs was analyzed under the condition of 45 m and 60 m span of the roof in the goaf.
StressDistribution
(MPa)
Distance from Goaf Edge
Flac Simulation
51. 44
Maximum vertical stress of about 8 to 9 MPa (Table 4.1) was indicated in the numerical
model at the side of the gallery located in the middle of the panel, while the roof is under
tension. Such situation may lead to tensile failure of the roof and need proper support to
reinforce the roof and spalling of sides in the middle of the panel. After exposure of about 40
m clear span in the goaf, the 2.0 m wide rib is standing at safety factor of about 0.8 which
may not fail instantaneously. Whereas, after exposure of about 60 m clear span in the roof,
safety factor of the rib may be reduced to 0.5, which would crush without causing any
adverse conditions to the advance workings.
53. 46
RESULTS
Subsidence movement, stress, strength and safety factor investigations conducted over short
wall led to the following results:
1. The subsidence monitoring in shallow depth workings where the effect of subsidence is
more severe and quickly felt was essential to estimate the overhang in goaf behind the
face and consequent transference of strata pressure or abutment pressure to the face and
to the immediate advanced gallery of the short wall panels.
2. The subsidence was largely depends on the geometry and configurations of the panel,
nature and matrix of the overlying strata, geo-technical properties of the strata and
induced caving from surface.
3. The width-depth ratios were 1.84 to 3.25 and new were from 1.84 to 2.4 in the extracted
short wall panels.
4. The maximum observed subsidence was 1.58m and the subsidence factor was 0.42 to
0.63 for all the short wall panel.
Subsidence was not reaching surface instantaneously. The subsidence was occurred in
stages at particular point. The major surface depression was achieved in about 6-9 days.
The magnitude of the residual subsidence after one year from the completion of
extraction in the panels varies from 4.08% to 6.45% of the total subsidence.
5. The maximum slope, maximum compressive strain and maximum tensile strain were
109mm/m, 69mm/m and 67mm/m respectively on the ground.
6. The maximum and minimum safety factor was 5.68 and 3.11 respectively.
7. The width of the subsidence induced cracks ranged from few mm to 350mm.
8. The maximum stress calculate by the Flac-5.0 software was 5MPa.
55. 48
CONCLUSIONS
Based on laboratory testing of coal samples, empirical and numerical modelling studies
related to the stability of the pillar and analysis of observation data on subsidence profiles for
underground coal mine, the following conclusions are drawn:
1) Field observations at Kumda underground mine indicated stability of the pillars without
any perceptible side spilling and crushing.
2) Uniaxial compressive strength, triaxial testing of coal samples indicated, UCS,
cohesion(C) and internal friction angle(∅) of 27.9MPa, 1.85 MPa and 300
,respectively.
3) Empirical and numerical modelling using two dimensional continuum analysis indicated
the maximum stress of 5 MPa over the pillar and safety factor exceeding 2 confirming to the
qualitative observation of stability of the pillar.
4) Maximum subsidence of 1.58 m was observed over the extracted panels with a subsidence
factor of 0.63 for the depillaring panels with the width and depth of 64 m-14 m, 30 m-45.5 m
respectively.
56. 49
REFRENCES
[1] Mark, C., 1981-2006, the evolution if intelligent coal pillar design, P.P: 2-4.
[2] Peng, S. S. Coal mine ground control. New York, John Wiley & Sons. 1978. pp. 181-
182.
[3] Wagner, H., (1980). Pillar design in coal mines. J.S. Afr. Min. Metal., V80, pp. 37-
45.
[4] Bieniawski, Z.T., 1992, Ground Control, Chapter in Mining Engineering Handbook,
SME, and P.P: 897-937.
[5] Singh, R.D., Principles and Practices of Modern Coal Mining‖, New Age International
Limited Publishers, 1st Edition, 2005, Chapter 6, pp. 156-180.
[6] Bieniawski, Z.T. (1968). The effects of specimen size on the compressive strength of
coal. Int. J. Rock Mech. Min Sci. Vol. 5, pp.325-335.
[7] Das, M N, 1986. Influence of width to height ratio on post-failure behaviour of coal,
International Journal of Mining and Geological Engineering, 4:79-87.
[8] Sheorey P. R. Pillar strength considering in situ stresses. Workshop on Coal Pillar
Mechanics and Design, pp. 122-127. Santa Fe, USBM IC 9315 (1992).
[9] Roberts D.P., Van der Merwe J.N., Canbulat EJ Sellers I., and Coetzer S.,
“Development of a method to estimate coal pillar loading”, Report No : 2001-0651,
September 2002.
[10] Srivastava, B.K. & Jaiswal, Ashok, Numerical simulation of coal pillar strength
(2009), International journal rock mechanics and mining sciences 46 (2009) 779-788,
Elsevier Ltd.
[11] Kushwaha, A, Shorey P.R. , Mohan, G.M., Numerical estimation pillar strength in
coal mine (2001), International journal rock mechanics and mining sciences 38 (2001)
1185-1192, Elsevier Ltd.