The patient who requires a single denture opposing a natural or restored dentition challenges the clinician even more than the completely edentulous patient does. This is due to the biomechanical differences in the supporting tissues of the opposing arches. So a proper evaluation, correction of the existing factors and proper sequence of denture construction is necessary to give a more stable prosthesis.
The Indian Dental Academy is the Leader in continuing dental education , training dentists in all aspects of dentistry and offering a wide range of dental certified courses in different formats.
A single complete denture is a removable appliance that fits against some or all of the natural teeth, a fixed restoration, or a previously constructed removable partial denture or a complete denture
The patient who requires a single denture opposing a natural or restored dentition challenges the clinician even more than the completely edentulous patient does. This is due to the biomechanical differences in the supporting tissues of the opposing arches. So a proper evaluation, correction of the existing factors and proper sequence of denture construction is necessary to give a more stable prosthesis.
The Indian Dental Academy is the Leader in continuing dental education , training dentists in all aspects of dentistry and offering a wide range of dental certified courses in different formats.
A single complete denture is a removable appliance that fits against some or all of the natural teeth, a fixed restoration, or a previously constructed removable partial denture or a complete denture
A single complete denture is a complete denture that occludes against some or all of the natural teeth, a fixed restoration, or a previously constructed removable partial denture or a complete denture.
Opposing natural teeth that are sufficient in number and do not necessitate a fixed or removable partial denture.
Opposing a partially edentulous arch in which the missing teeth have been or will be replaced by a fixed partial denture.
Opposing arch with an existing complete denture.
Diagnosis and treatment planning in implants/ cosmetic dentistry trainingIndian dental academy
Indian Dental Academy: will be one of the most relevant and exciting
training center with best faculty and flexible training programs
for dental professionals who wish to advance in their dental
practice,Offers certified courses in Dental
implants,Orthodontics,Endodontics,Cosmetic Dentistry, Prosthetic
Dentistry, Periodontics and General Dentistry.
Diagnosis and treatment planning in implants / esthetic dentistry coursesIndian dental academy
Indian Dental Academy: will be one of the most relevant and exciting
training center with best faculty and flexible training programs
for dental professionals who wish to advance in their dental
practice,Offers certified courses in Dental
implants,Orthodontics,Endodontics,Cosmetic Dentistry, Prosthetic
Dentistry, Periodontics and General Dentistry.
Diagnosis and treatment planning in implants 2. / dental implant courses by ...Indian dental academy
Description :
The Indian Dental Academy is the Leader in continuing dental education , training dentists in all aspects of dentistry and
offering a wide range of dental certified courses in different formats.for more details please visit
www.indiandentalacademy.com
Occlusion in cd /certified fixed orthodontic courses by Indian dental academy Indian dental academy
The Indian Dental Academy is the Leader in continuing dental education , training dentists in all aspects of dentistry and offering a wide range of dental certified courses in different formats.
Indian dental academy provides dental crown & Bridge,rotary endodontics,fixed orthodontics,
Dental implants courses.for details pls visit www.indiandentalacademy.com ,or call
0091-9248678078
Diagnosis and treatment planning in implants 2. /certified fixed orthodontic ...Indian dental academy
The Indian Dental Academy is the Leader in continuing dental education , training dentists in all aspects of dentistry and offering a wide range of dental certified courses in different formats.
6- Prosthetic Problems and possible solutions in Setting –up of teeth for ske...Amal Kaddah
COMPLETE DENTURE CONSTRUCTION
1- Diagnosis and Treatment Planning for Removable Prosthodontics
2- Preliminary Maxillary and mandibular impression procedures
3- Final Maxillary and mandibular impression procedures
4- Jaw Relation Registration
a. Introduction and the stomatognathic system
What 'occlusion' is and why it is important
b. Definitions.
c. Check denture foundation and Establishment of facial contour.
d. Establishment of the occlusal plane.
e. Importance of mounting the maxillary cast using Maxillary face-bow record and transfer.
f. Determination of vertical dimension of centric occluding relation.
g. Determination of centric and eccentric relations at the accepted vertical dimension.
5- Selection of Artificial Teeth
6- Prosthetic Problems and possible solutions in Setting –up of teeth for skeletal Class I, II and Class III arch relationship of completely edentulous patients.
7- Try-in of the wax trial complete denture.
8- Complete denture insertion (Delivery)
9- Occlusal corrections.
10- Managements of Post Insertion Problems and Complaints.
11- Single denture and Kelly's Syndrome
12- Denture Processing and Laboratory Errors.
Welcome to TechSoup New Member Orientation and Q&A (May 2024).pdfTechSoup
In this webinar you will learn how your organization can access TechSoup's wide variety of product discount and donation programs. From hardware to software, we'll give you a tour of the tools available to help your nonprofit with productivity, collaboration, financial management, donor tracking, security, and more.
This is a presentation by Dada Robert in a Your Skill Boost masterclass organised by the Excellence Foundation for South Sudan (EFSS) on Saturday, the 25th and Sunday, the 26th of May 2024.
He discussed the concept of quality improvement, emphasizing its applicability to various aspects of life, including personal, project, and program improvements. He defined quality as doing the right thing at the right time in the right way to achieve the best possible results and discussed the concept of the "gap" between what we know and what we do, and how this gap represents the areas we need to improve. He explained the scientific approach to quality improvement, which involves systematic performance analysis, testing and learning, and implementing change ideas. He also highlighted the importance of client focus and a team approach to quality improvement.
Operation “Blue Star” is the only event in the history of Independent India where the state went into war with its own people. Even after about 40 years it is not clear if it was culmination of states anger over people of the region, a political game of power or start of dictatorial chapter in the democratic setup.
The people of Punjab felt alienated from main stream due to denial of their just demands during a long democratic struggle since independence. As it happen all over the word, it led to militant struggle with great loss of lives of military, police and civilian personnel. Killing of Indira Gandhi and massacre of innocent Sikhs in Delhi and other India cities was also associated with this movement.
How to Create Map Views in the Odoo 17 ERPCeline George
The map views are useful for providing a geographical representation of data. They allow users to visualize and analyze the data in a more intuitive manner.
The French Revolution, which began in 1789, was a period of radical social and political upheaval in France. It marked the decline of absolute monarchies, the rise of secular and democratic republics, and the eventual rise of Napoleon Bonaparte. This revolutionary period is crucial in understanding the transition from feudalism to modernity in Europe.
For more information, visit-www.vavaclasses.com
Palestine last event orientationfvgnh .pptxRaedMohamed3
An EFL lesson about the current events in Palestine. It is intended to be for intermediate students who wish to increase their listening skills through a short lesson in power point.
7. Problems of Single Denture
1- Difficulties – Maxillary Denture
Opposing Dentate Mandible
8. With single complete dentures, the
natural dentition opposing the
edentulated arch often exhibits an
uneven occlusal plane.
i.e. a “mutilated” dentition
Complete Dentures Opposing
Dentate Arch
10. • Occlusal discrepancies*
• Excessive load
* These all predispose to tipping of the
denture and the generation of lateral
forces which can lead to compression of
the periosteum, disruption of the
vasculature and a resorptive remodeling
response of the maxilla.
11. Right working
Maxillary Denture Opposing Dentate Mandible
Centric occlusion •The patient wore this denture
for more than 10 years. Note
the resorption of the maxilla
and the wear associated with
the posterior mandibular
dentition.
•Note the patient in the right
working position. There are
no balancing contacts on the
opposite side.
Resorbed maxilla
12. The Subsequent problems with single
denture against natural teeth
1- Great force generated by the natural teeth.
Excessive pressure result in resorption of the
residual ridge & hyperplastic tissues.
2- Malposed, tipped, or super erupted teeth in the
lower arch make it difficult to achieve a
harmonious balanced occlusion.
3- The presence of the mandibular anterior teeth
makes the esthetic and phonetic placement
difficult.
13. 4- Increase the tendency of fracture of
maxillary denture due to occlusal
stresses exerted by natural teeth.
5- Abrasion of the artificial teeth if
acrylic is used or the abrasion of
natural teeth if porcelain is used.
6- Combination syndrome and
associated changes.
7- Mandibular single denture.
14. How To Overcome These Problems
-The primary consideration for a continued success of a
single complete denture is the preservation of that
which remains,
-Proper diagnosis and full use of every factor, which
favor success for this denture,
- Applying the principles of c. d construction
Reduction of the forces to which the denture is subject
Maximum base extension within functional anatomical
limits (distribution of forces
over the largest possible area of supporting structures
and the force per unit area kept at minimum.)
15. The polished surface: The creation of the
correct form of the polished surfaces.
The fitting surface: Good impressions that
yield an accurate fit spreading the bite load
out over the entire ridge.
The border Extension: Proper denture
border lengths that allow for free movement
of musculature and tissue attachments.
16. Occlusion:
A balanced occlusion and
free articulation creating an
uniform application of bite
force down on to your ridge.
17. Steps for Single Denture construction
• Proper Diagnosis and mounting the diagnostic
casts.
• Occlusal Adjustment and Tooth Modification
• Final Impression.
• Jaw relation.
• Face bow transfer.
• Artificial teeth adjustment and Try-in of waxed
denture.
• Delivery.
18. Check Out the Opposition
• Ridge relationship
• Interdental space
• Occlusal plane
• Tooth position
• Cuspal inclination
• Rotations
• Tooth wear
Proper Diagnosis and mounting the diagnostic casts
19.
20. Mutilated Dentition
• Extrusion, tipping, rotation
• Sharp, steep unworn cusps
• Spaces
• Cross-bite relationships
• Natural teeth inclines may prevent
development of balanced occlusion
22. Strategies for prevention of resorption
• Correct occlusal discrepancies
a) Reshaping by grinding
b) Provide new restorations
c) Reshape with RPD framework
• Retain root tips particularly in the premaxilla
to facilitate support
• Place osseointegrated implants to facilitate
support
*Avoid excessive vertical overlap of
the anterior denture teeth.
28. Swenson’s Technique
Casts mounted on articulator
using provisional CR at
acceptable vertical Dimension
Maxillary record base made
and Denture teeth are set
If lower teeth interfere with placement of denture teeth,
stone teeth are adjusted and marked on the cast with
pencil .
The natural teeth are modified using the diagnostic cast
as a guide
29. Occlusal Plane Discrepancies
• The occlusal plane
discrepancy is
readily apparent
when the denture
teeth are properly
arranged.
• This discrepancy can
only be corrected by
restorative means.
33. Boucher Technique
The interferences are removed by
movement of the maxillary porcelain
teeth over the mandibular stone teeth.
Prematurities are identified and
removed by grinding the natural teeth.
The procedure is repeated for right and
lateral excursions until a harmonious
balanced occlusion is established.
34. Yurkstas Technique
The use of a metal U-shaped occlusal
template that is slightly convex on the
lower surface is placed on the occlusal
surfaces of the remaining teeth.
20° Template
37. Impression Making
An ideal impression should provide: (Objectives of
impression making)
• Maximum extension without muscle impingement.
• Intimate contact with the tissue area covered.
• Proper form of the borders including the posterior border of
the maxillary denture.
• Proper relief of hard and sensitive areas.
• To equalize forces on the denture foundation
area.
39. Recording Intermaxillary Relations
for Single Upper Denture
• Freely removing from the
upper rim whatever quantity
of wax is necessary to
achieve the required degree
of jaw closer. The incisal
level of the upper front teeth
and the occlusal plane can
be determined later by
reference to the lower
natural teeth.
40. (A) The artificial incisor has been set farther back and lower than
its natural predecessor, thereby providing a locked and potentially
traumatic occlusion. (B) The overbite has been reduced by raising
the tip of the lower incisor. The overjet has been increased by
moving the upper incisor forward to its correct position and by
grinding the labioincisal surface of the lower incisor.
41. Maxillo - Mandibular Relations
• Centric Registration
– CUD usually stable
– Extraoral hand
position if opposing
natural dentition (less
obtrusive)
42. Jaw relation, face bow transfer,
artificial teeth adjustment and check
waxed denture
44. Harmonious balanced occlusion in complete single
denture can be achieved either by
I - Statically equilibrated occlusion using a
programmed articulator to stimulate the
patient’s mandibular movements.
a- Articulator equilibrated technique.
b- Articulator generated path technique.
II - Dynamically equilibrated occlusion by the use
of functional generated path technique
(Functional chew-in techniques)
Methods Used To Achieve Balance Articulation:
45. Complete Dentures Opposing
Dentate Arch
• What is the principle challenge?
Designing a denture occlusion with bilateral
balanced occlusion.
•Why is bilateral balance so important?
Tipping of the denture and excessive lateral forces
lead to resorption of the edentulous arch
Ensure that the opposing dentition
can be made level
46. The simultaneous contact of the
maxillary and mandibular teeth on the
right and left and in the anterior and
posterior occlusal areas when the
jaws are in either centric or eccentric
relation, within the normal range of
mandibular function
? ? ? ? ? ?
47. Balanced sliding occlusion
(free articulation)
The even contacting of teeth as the
mandible moves to and from
eccentric to centric
maxillomandibular relations (any
mandibular movement made
without interference.)
48. Single Denture Occlusion
• “An occlusal scheme that
employs a multiplicity of point
contacts, rather than one that
utilizes broad-surfaced contacts
on inclined planes is advocated.”
John J. Shary
50. Posterior Tooth Arrangement
• Shary Concept
– No interdigitation (cusp to fossa)
– Cusp to cusp
• Maxillary Lingual VS mandibular Buccal
• c.f. “Lingualized”
– Avoid broad inclined planes
51. When the occlusal plane has been
levelled , what type of occlusion will
we have?
this
or
this
52. The second choice is more likely because:
• Natural tooth guidance would have a
tendency to dislodge the denture
• The natural teeth are seldom situated in
positions that allow the cusp to fossae,
cusp to embrasure relationship
53. The Golden Rule
for this type of case
Equal contacts in centric
occlusion and no interferences
in excursive movements
(commonly referred to as
functional occlusion)
59. Metal Occlusal Surfaces
In patients with the financial resources, gold occlusals can be
used to minimize wear of the occlusal surfaces. In patients
with limited financial resources, amalgam stops can be
inserted into the cusp tips of the acrylic resin denture teeth.
60. 1- Porcelain teeth :
Wear very slowly and therefore the
occlusal vertical dimension is maintained.
cause rapid wear of opposing natural teeth
and may be exposed.
2. Acrylic resin teeth :
No wear of the opposing natural teeth,
they are the teeth of choice. The major
disadvantage of resin teeth is their wear,
which results in loss of vertical dimension.
61. 3- Acrylic resin with gold occlusal surfaces:
although gold occlusals are considered the best material to
oppose natural teeth, their expense and the time involved in
their fabrication.
4- Acrylic resin with amalgam stops:
reduce the occlusal wear, and the technique is simple less time
consuming and less expensive than with the gold occlusals.
5. IPN resin:
The wear resistance is higher than that of the conventional
acrylic resin teeth.
64. A- The Esthetic Factors Dictated A Steep Vertical
Overlap With Little Horizontal Overlap. Therefore
Steeper Posterior Cuspal Inclines Had To Be
selected
B- In eccentric movements the inclinations of the
posterior cusps are sufficient to prevent anterior
interference.
65. A- the esthetic factors allowed for an adequate
amount of horizontal overlap so that shallow cuspal
inclines were able to be selected.
B- In eccentric movements the shallow posterior
inclines are sufficient to prevent anterior
interference.
66. Arrangement of Denture Teeth
• Incisal angle
The flatter the angle the more
stable the denture.
Esthetics is often the driving issue. If you increase
the vertical overlap to an excessive degree to
satisfy the esthetic desires of the patient, you
loose balance, the denture is tipped anteriorly and
the long insidious process of resorption is set
motion.
67. Incisal Angle
This cast is being used to
fabricate an immediate
denture. Note the excessive
amount of vertical overlap of
the remaining anterior teeth.
If this amount of vertical overlap is incorporated into the denture the
occlusion will not be in balance, the denture will be tipped anteriorly
during function, and the premaxilla will resorb.
What are your options?
a) Reduce the amount of overlap by raising the incisal
edges of the denture teeth.
b) Reduce the length of the mandibular anteriors.
c) A combination of both (a) and (b).
71. Edentulous Mandible Opposing Dentate Maxilla
•Conventional dentures are
contraindicated because they
cause severe resorption as seen in
this patient. In past years many
prosthodontists recommended
extraction of the remaining
maxillary teeth. Today other options are
available.
73. In the mandible, the limited denture bearing
area will lead to advanced residual ridge
resorption of the edentulous mandible.
For this reason, a lower complete denture
opposing upper natural teeth should be
avoided . A lower complete denture
opposing upper natural teeth is acceptable
for patients with class III jaw relation. and
for a patient with cleft palate
Edentulous Mandible Opposing Dentate Maxilla
74. • Avoid creating this situation if
possible
• If construction of this denture
is unavoidable ensure that the
opposing teeth are on a level
plane.
Edentulous Mandible Opposing Dentate Maxilla
75. A level plane may be established by
extraction, grinding of cusps,
crowns or occlusal build-ups
Edentulous Mandible Opposing Dentate Maxilla
76. • Maximize denture base coverage
• Minimized occlusal forces
• Preprosthetic surgery
• Retention of key roots
• Use of osseointegrated implants
• Temporary soft liners replaced on a regular
basis
• Permanent soft liners
Options other than extraction of maxillary dentition
For Preservation of the Residual Alveolar Ridge
Edentulous Mandible Opposing Dentate Maxilla
77. Ridge Augmentation
A variety of materials have been used for
this purpose:
Autogenous bone from the iliac crest or rib.
Non-autogenous bone.
Hydroxyapatite, (in the granular or block form)
which is injected through one or more
subperiosteal tunnels to build up sufficient height
of the residual ridge.
81. Retained Roots
Retaining roots in key positions facilitate support and prevent
compression of the periosteum. In this patient a cuspid and a
premolar root have been retained. Support in the posterior
region, however, must still be provided by the retromolar pad,
the buccal shelf and the residual alveolar ridge.
The excessive loads delivered to these areas will result in
continued resorption of the mandibular body.
82. Osseointegrated Implants
• Implant assisted overlay dentures opposing
dentate maxilla
The implants are used to facilitate retention, stability, and provide
support in the anterior region. Posterior occlusal loads, however,
must be borne by the retromolar pad, the buccal shelf and the
residual alveolar process. A carefully made border molded
impression will make maximum use of these support areas.
83. Osseointegrated Implants Opposing Dentate Maxilla
• Implant supported prostheses – All the
occlusal forces are borne by the implants
This type of prosthesis stops the process of resorption of the
mandible and in many patients the volume of the body of the
mandible posterior to the mental foramen actually increases. It
is therefore the most desirable method for restoring the
edentulous mandible that opposes a fully dentate maxilla.
87. Questions for Review
1) Name the five factors affecting occlusal balance. (10 points)
2) Why is it difficult to achieve bilateral balance with a complete
denture that opposes an intact dentate arch? (6 points)
3) Define combination syndrome. (4 points)
4) In the past many prosthodontists recommended extracting the
remaining maxillary teeth when opposed by an edentulous
mandible. Why? What are the options available today? Which
option is preferred and why is this option preferred? (14 points)
5) Discuss in detail the strategies you would use when restoring an
edentulous arch that opposes a fully dentate arch to prevent or
minimize resorption of the edentulous arch. ( 10 points)
6) When fabricating a maxillary denture opposing a fully dentate
mandibular arch what are the consequences of arranging the
maxillary anterior denture teeth with excessive vertical overlap?
(4 points)
88. Typical examination questions
• In an organized summary, discuss the
problems of the single denture wearer
and possible solutions to specific
problems .
• Discuss the problems faced by the
patient wearing a specific type of
single denture and propose strategies
to cope with the problems.
89. REFERENCES
Carr AB. Single Dentures. In: Zarb GA, et al, editors. Prosthodontic Treatment
for Edentulous Patients. 12 th ed. St.Louis: Mosby; 2004. p. 427-436.
Heartwell CM, Rahn AO, editors. Textbook of Complete Dentures. 5th ed.
Canada: B.C. Decker; 2002. p. 481-492. .
Stephens AP. The Single Complete Denture. In: Sharry JJ, editor. Complete
Denture Prosthodontics. 3rd ed. New York: McGraw – Hill; 1962 p. 310-319.
Lauciello FR. The Single Complete Maxillary Denture. In: Winkler S, editor.
Essentials of Complete Denture Prosthodontics. 2nd ed. USA: Ishiyaku Euro
America Inc; 1996. p. 417-426.
Langer Y et al. Modalities of Treatment for the Combination Syndrome. JOP
1995: 4; 76 - 81.
Kelly E. Change caused by a mandibular removable partial denture opposing a
maxillary complete denture. J Prosthet Dent 1972: 27; 140 -150.
Vig RG. A Modified Chew - In and Functional Impression Technique. J
Prosthet Dent 1964: 14; 214 – 220.
94. Complete Denture Opposing Fixed
• Use of 2nd molar as a balancing ramp
The incisal angle is manipulated to be compatible
with angle of the second molar to the occlusal plane.
Centric Occlusion Protrusive Position
95. Complete Denture Opposing Fixed
Note the occlusal plane
discrepancy (A,B). The plane
of the maxillary denture is
idealized (B) before the
preparation of the opposing
dental units is commenced.
The trial denture is shown
opposing a diagnostic waxup
(C).
A
C
B
96. Incisal Angle
This cast is being prepared for
an immediate denture. In this
patient the amount of vertical
overlap is being reduced
flattening the incisal angle and
making it compatible with
condylar guidance and the curve
of Spee.
97. Complete Denture Opposing Fixed
In this patient the
occlusal plane of the
mandibular arch was
idealized with fixed
restorations.
Note: The cuspal inclinations of the posterior maxillary
denture teeth are relatively flat and the compensating curve
is 15 to 20 degrees. The incisal angle is compatible with
the angle of the compensating curve. During function
tipping of the denture will be minimized and therefore
resorption minimized.