This process report highlights the significance of Dynamic Simulation in Aspen HYSYS for calculation of maximum flow rate of natural gas through a pipeline supplying gas to domestic consumers. The gas pressure at the outlet of pipeline has been considered to be equal to 0 psig in order to calculate the maximum possible gas flow rate. Moreover, the reduction of gas pressure at upstream of gas regulating station due to increased downstream pressure has also been calculated using this simulation.

1. October 24, 2014
1
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
Calculation of Maximum Flow of Natural Gas through a Pipeline using Dynamic Simulation in Aspen HYSYS
Muhammad Waqas Manzoor
Process Engineer
Email: engr.waqasmanzoor@gmail.com
Synopsis:
A dynamic simulation in Aspen HYSYS was performed to assess the maximum gas carrying capacity of a NPS 6” SCH 80 pipeline having length of 12 km. At upstream end, the pipeline is connected with a Natural Gas Regulating Station and at downstream end the pipeline is connected with domestic consumer pipeline network. The pressure required by domestic consumer is very less compared with the pipeline pressure i.e. about 4 inches WC = 0.144 psig. Therefore, to calculate the maximum flow (or choke flow) through the pipeline, 0 psig has been considered at downstream of the NPS 6” SCH 80 12 km long pipeline. The pipeline absolute roughness for calculation of frictional pressure drop has been considered to be equal to 0.04572 millimeters, which is the same as of carbon steel pipes.
Background Information:
The Natural Gas Regulating Station can supply gas at a pressure of 40 psig to 100 psig, using a pressure control valve, as per the seasonal consumer demand. During winter season the pressure may be increased to 100 psig and during summer season the pressure may be reduced to 50 psig because gas consumption during winter season is higher as compared to that in summer season, and only by increasing the gas pressure at the downstream of the Natural Gas Regulating Station, the gas flow rate can be increased. The pressure at the upstream of the Natural Gas Regulating Station is about 395 psig. However, it depends on pressure setting at downstream of Natural Gas Regulating Station. Higher the downstream pressure, higher would be gas flow rate and lower would be the upstream pressure.
Natural Gas Regulating Station
Inlet Pressure = 400 to 500 psig
Outlet Pressure = 50 to 100 psig
6”Pipeline 12km
Domestic Consumer Network
Required 2 to 3 MMSCFD in 2014
Forecast for 2015 is 5 to 6 MMSCFD
6”Offtake 20 meters
16”Burried Mainline near Natural Gas Regulating Station

2. October 24, 2014
2
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
HYSYS Simulation Results:
Following are the results of the Dynamic Simulation,
S. No.
Pressure at U/S of Regulating Station (psig)
Pressure at D/S of Regulating Station (psig)
Max. Flow rate across NPS 6” 12 km long pipeline at D/S of Regulating Station (MMSCFD)
1.
397.0
50
2.08
2.
396.4
60
2.46
3.
395.2
80
3.23
4.
394.6
90
3.62
5.
394.0
100
4.01
It may also be noted that the actual absolute roughness would also be higher than 0.0457 millimeters depending on the aging of pipeline and therefore, the actual maximum flow rate would be less than the values calculated in this simulation. Therefore, the said line would be unable to cater the natural gas demand if it increases beyond 4 MMSCFD in 2015, as per the forecast.
The application of Dynamic Simulation in this particular case holds significance because Steady State Simulation cannot simulate pressure balancing and therefore, can never imitate actual process in which flow rate depends on pressure differential only. Even the pipe model in Steady State Simulation was unable to calculate natural gas flow rate after the total pressure drop had been specified across the 6” dia. 12 km long pipeline.

3. October 24, 2014
3
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
Gas Composition
The average gas composition for last month at the Regulating Station is used in the HYSYS Simulation.
HYSYS Simulation Snapshots
All these simulation snapshots were taken after the variables had reached their maximum or minimum values.
Maximum Flow rate for 50 psig is 2.08 MMSCFD

4. October 24, 2014
4
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
Maximum Flow rate for 60 psig is 2.46 MMSCFD
Maximum Flow rate for 80 psig is 3.23 MMSCFD

5. October 24, 2014
5
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
Maximum Flow rate for 90 psig is 3.62 MMSCFD
Maximum Flow rate for 100 psig is 4.01 MMSCFD

6. October 24, 2014
6
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
Steady State Simulation
The pipe model in Steady State Simulation was unable to calculate natural gas flow rate after the total pressure drop had been specified across the 6” dia. 12 km long pipeline. Total Pressure Drop = 50 psig - 0 psig = 50 psi

7. October 24, 2014
7
---- Muhammad Waqas Manzoor ---- Process Engineer ---- Engr.waqasmanzoor@gmail.com ----
Flow rate calculation using Different Pressure Drop Correlations
Below is the comparison between flow rate calculated using different pressure drop correlations in the Dynamic Simulation of only the 6” pipe,