In this paper, two antennas are designed using substrate integrated waveguide (SIW) and microstrip technology at 28 GHz. Parametric study for both antennas is presented to demonstrate the performance at millimeter wave frequency for wireless communication network (5G application). Roger RT5880 substrates with permittivity 2.2 and loss tangent 0.0009 are used to implement the antennas with two thicknesses of 0.508 mm and 0.127 mm respectively. Both antennas have the same size of substrate 12x12 mm with a full ground plane was used. Structures designs have been done by using computer simulation technology (CST). The simulation results showed that the antenna with SIW and roger RT 5880 substrate thickness 0.508 has better performance in term of return loss and radiation pattern than the microstrip patch antenna at 28 GHz. A return loss more than -10 dB and the gain are 6.4 dB obtained with wide bandwidth range of (27.4-28.7) GHz. This proving to increase the realized gain by implementing SIW at millimeter wave band for 5G application network.
Design of substrate integrated waveguide withMinkowski-Sierpinski fractal ant...journalBEEI
This paper presents a new design of patch antenna using Minkowski-Sierpinski fractal technique with substrate integrated waveguide (SIW) to resonate at 60 GHz. The antenna is proposed to be used for wireless body area network applications (WBAN). The proposed antenna is implemented using Rogers 5880 substrate with permittivity of (εr) of 2.2 and loss tangent is 0.0004, height of the substrate is 0.381 mm. Computer simulation technology-Microwave Studio (CST-MW) is used to simulate the proposed antenna. The simulated results show a wide bandwidth of 3.5 GHz between the ranges of (58.3-61.7) GHz, with a good return loss of more than -10 dB. A simulated gain of 7.9 dB is achieved with a linear antenna efficiency of 91%. This proposed antenna is used to improve the quality of radiation pattern, bandwidth, and gain at millimetre wave (mm-Wave) band for WBAN applications.
Higher order mode dielectric resonator antenna excited using microstrip linejournalBEEI
In this paper, the square-shaped dielectric resonator antenna (DRA) operating on higher order (푇퐸훿13) mode for the fifth generation (5G) communication applications is presented. The proposed DR antenna is excited by using a microstrip feed line and designed at the operating frequency of 28 GHz. The Rogers RT/Duroid 5880 material having a thickness of 0.254mm and a dielectric constant of 2.2 is used for the substrate. The commercial CST microwave studio (CST MWS) is used for the optimization and simulation of the antenna design. The reflection coefficient, antenna gain, radiation efficiency, VSWR and radiation pattern are studied. A -10dB bandwidth of 4.6% (1.3 GHz) for VSWR<2 with a gain of 5 dBi and radiation efficiency of 89%. The proposed antenna design is suitable for future 5G wireless communication applications.
Bandwidth Improvement of UWB Microstrip Antenna Using Finite Ground PlaneIJERA Editor
Microstrip antennas play a vital role in communication system. It is required in high performance wireless applications. But due to its resonant nature microstrip antennas have some considerable drawbacks like narrowband performance. Extensive study has been carried out on microstrip patch antennas in the recent past, but it still have large scope for improvement in the near future. To overcome narrow bandwidth problem, number of methods and techniques have been suggested and investigated, keeping in mind that the basic advantages of microstrip antenna should not be altered such as low profile, light weight, low cost and simple printed circuit structure. The area of investigation includes modification in geometrical shape of the antenna, use of resonators, use of dipole, and many other parameters. This paper presents a comparison between conventional microstrip antenna and microstip antenna with finite ground plane at ultra wideband. HFSS simulation tool is used here for antenna simulation. For feeding purpose microstrip feed line is used (50Ω). Optimized result provides impedance bandwidth of 7.2GHz with VSWR<2, operating frequency range is from 6.5GHz to 13.7GHz. Proposed antenna is useful for many ultra wideband applications. =
Design LTE Microstrip Antenna Rectangular Patch with Beetle-Shaped SlotTELKOMNIKA JOURNAL
In this paper, the microstrip antenna rectangular patch with beetle shaped slot is presented. The
characterization results of the proposed antenna obtained by changing the dimensions of the ground
plane. CST software is used to design and analyze this proposed antenna. The simulated results of
proposed antenna show that the antenna works at the frequency of 2.1 GHz while the return loss of -32.18
dB with the bandwidth reaches 155.19 MHz and the gain of 3.895 dBi.
Wideband and high gain dielectric resonator antenna for 5G applicationsjournalBEEI
In this paper, wideband high gain dielectric resonator antenna for 5G applications is presented. Higher order mode is exploited to enhance the antenna gain, while the array of symmetrical cylindrical shaped holes drilled in the DRA to improves the bandwidth by reducing the quality factor. The proposed DRA is designed using dielectric material with relative permittivity of 10 and loss tangent of 0. 002.The Rogers RT/Droid 5880 has been selected as substrate with relative permittivity of 2.2, loss tangent of 0.0009- and 0.254-mm thickness. The simulated results show that, the proposed geometry has achieved a wide impedance bandwidth of 17.3% (23.8-28.3GHz=4.5 GHz) for S11<-10 dB, and a maximum gain of about 9.3 dBi with radiation efficiency of 96% at design frequency of 26 GHz. The DRA is feed by microstrip transmission line with slot aperture. The reflection coefficient, the radiation pattern, and the antenna gain are studied by full-wave EM simulator CST Microwave Studio. The proposed antenna can be used for the 5G communication applications such as device to device communication (D2D).
expanding the bandwidth of rectangular microstrip antenna by inserting a slotINFOGAIN PUBLICATION
In this work we were able to improve the reflection coefficient S11 and bandwidth BW of a rectangular microstrip antenna fed by a coaxial cable firstly by adjusting a the feed point and secondly by inserting a rectangular slot in the radiating element The results obtained using the HFSS software, have been compared by those published. These results are very satisfying.
Design of substrate integrated waveguide withMinkowski-Sierpinski fractal ant...journalBEEI
This paper presents a new design of patch antenna using Minkowski-Sierpinski fractal technique with substrate integrated waveguide (SIW) to resonate at 60 GHz. The antenna is proposed to be used for wireless body area network applications (WBAN). The proposed antenna is implemented using Rogers 5880 substrate with permittivity of (εr) of 2.2 and loss tangent is 0.0004, height of the substrate is 0.381 mm. Computer simulation technology-Microwave Studio (CST-MW) is used to simulate the proposed antenna. The simulated results show a wide bandwidth of 3.5 GHz between the ranges of (58.3-61.7) GHz, with a good return loss of more than -10 dB. A simulated gain of 7.9 dB is achieved with a linear antenna efficiency of 91%. This proposed antenna is used to improve the quality of radiation pattern, bandwidth, and gain at millimetre wave (mm-Wave) band for WBAN applications.
Higher order mode dielectric resonator antenna excited using microstrip linejournalBEEI
In this paper, the square-shaped dielectric resonator antenna (DRA) operating on higher order (푇퐸훿13) mode for the fifth generation (5G) communication applications is presented. The proposed DR antenna is excited by using a microstrip feed line and designed at the operating frequency of 28 GHz. The Rogers RT/Duroid 5880 material having a thickness of 0.254mm and a dielectric constant of 2.2 is used for the substrate. The commercial CST microwave studio (CST MWS) is used for the optimization and simulation of the antenna design. The reflection coefficient, antenna gain, radiation efficiency, VSWR and radiation pattern are studied. A -10dB bandwidth of 4.6% (1.3 GHz) for VSWR<2 with a gain of 5 dBi and radiation efficiency of 89%. The proposed antenna design is suitable for future 5G wireless communication applications.
Bandwidth Improvement of UWB Microstrip Antenna Using Finite Ground PlaneIJERA Editor
Microstrip antennas play a vital role in communication system. It is required in high performance wireless applications. But due to its resonant nature microstrip antennas have some considerable drawbacks like narrowband performance. Extensive study has been carried out on microstrip patch antennas in the recent past, but it still have large scope for improvement in the near future. To overcome narrow bandwidth problem, number of methods and techniques have been suggested and investigated, keeping in mind that the basic advantages of microstrip antenna should not be altered such as low profile, light weight, low cost and simple printed circuit structure. The area of investigation includes modification in geometrical shape of the antenna, use of resonators, use of dipole, and many other parameters. This paper presents a comparison between conventional microstrip antenna and microstip antenna with finite ground plane at ultra wideband. HFSS simulation tool is used here for antenna simulation. For feeding purpose microstrip feed line is used (50Ω). Optimized result provides impedance bandwidth of 7.2GHz with VSWR<2, operating frequency range is from 6.5GHz to 13.7GHz. Proposed antenna is useful for many ultra wideband applications. =
Design LTE Microstrip Antenna Rectangular Patch with Beetle-Shaped SlotTELKOMNIKA JOURNAL
In this paper, the microstrip antenna rectangular patch with beetle shaped slot is presented. The
characterization results of the proposed antenna obtained by changing the dimensions of the ground
plane. CST software is used to design and analyze this proposed antenna. The simulated results of
proposed antenna show that the antenna works at the frequency of 2.1 GHz while the return loss of -32.18
dB with the bandwidth reaches 155.19 MHz and the gain of 3.895 dBi.
Wideband and high gain dielectric resonator antenna for 5G applicationsjournalBEEI
In this paper, wideband high gain dielectric resonator antenna for 5G applications is presented. Higher order mode is exploited to enhance the antenna gain, while the array of symmetrical cylindrical shaped holes drilled in the DRA to improves the bandwidth by reducing the quality factor. The proposed DRA is designed using dielectric material with relative permittivity of 10 and loss tangent of 0. 002.The Rogers RT/Droid 5880 has been selected as substrate with relative permittivity of 2.2, loss tangent of 0.0009- and 0.254-mm thickness. The simulated results show that, the proposed geometry has achieved a wide impedance bandwidth of 17.3% (23.8-28.3GHz=4.5 GHz) for S11<-10 dB, and a maximum gain of about 9.3 dBi with radiation efficiency of 96% at design frequency of 26 GHz. The DRA is feed by microstrip transmission line with slot aperture. The reflection coefficient, the radiation pattern, and the antenna gain are studied by full-wave EM simulator CST Microwave Studio. The proposed antenna can be used for the 5G communication applications such as device to device communication (D2D).
expanding the bandwidth of rectangular microstrip antenna by inserting a slotINFOGAIN PUBLICATION
In this work we were able to improve the reflection coefficient S11 and bandwidth BW of a rectangular microstrip antenna fed by a coaxial cable firstly by adjusting a the feed point and secondly by inserting a rectangular slot in the radiating element The results obtained using the HFSS software, have been compared by those published. These results are very satisfying.
Design compact microstrap patch antenna with T-shaped 5G applicationjournalBEEI
This paper is presents a microstrap patch with a T-shaped rectangular antenna workings; the T-shaped patch operating at 3.6 GHz resonating frequency range for 5G application (from 2.9 to 4.4 GHz) repectively. The overall size of the proposed antenna is 22×24×0.25 mm3; the feeding technique using a 50 Ω feed line to the antenna. The proposed antenna is printed on compact Rogers RT 588 lz substrate having permittivity (ɛr) 2.00, loss tangent (tan δ) 0.0021, with thikness 0.2 mm. The proposed antenna introducesmany advantages like small size, low profile, and simpler structure. The characteristics such as radiation pattern, reflection coefficient, gain, current distribution, and radiation efficiency are respectively presented and discussed, using CST microwave study in simulating and analysing. Introducing a slot with a rectangular T-shaped patch antenna achieved lower frequency with 98.474% radiation efficiency and peak gain of the proposed antenna at 2.52 dB. The fractional bandwidth is 42.81% (2.90 GHz to 4.48 GHz) with a resonant frequency of 3.6 GHz and return loss at 28.76 dB. This frequency band attributessuited 5 G mobile application.
In this paper a compact, flexible, Multiband antenna is designed. It is having flexible Substrate of photographic paper which makes the antenna conformal. The antenna with two U slots cut in radiating patch is offset fed by microstrip lines gives the multiple bands of WLAN/WIMAX Application and two parasitic Elements improves the bandwidth of a typical microstrip antenna. The Measured results shows that the antenna resonates between Frequency band 2.10-2.95 GHz, 3.35-3.54 GHz and 5.04-6.0Hz.which are used for application such as Bluetooth, Wi-Fi, Zigbee, ISM 2.4GHz,WLAN WiMAX, and WLAN 5.2GHz.
5G Fixed Beam Switching on Microstrip Patch Antenna IJECEIAES
5G technology is using millimeter-wave band to improve the wireless communication system. However, narrow transmitter and receiver beams have caused the beam coverage area to be limited. Due to propagation limitations of mm wave band, beam forming technology with multi-beam based communication system, has been focused to overcome the problem. In this letter, a fixed beam switching method is introduced. By changing the switches, four different configurations of patch array antennas are designed to investigate their performances in terms of radiation patterns, beam forming angle, gain, half-power bandwidth and impedance bandwidth at 28 GHz operating frequency for 5G application. Mircostrip antenna is preferred due to its low profile, easy in feeding and array configurations. Three different beam directions had been formed at -15°, 0°, and 15° with half-power bandwidth of range 45˚ to 50˚.
In the present paper a circular slot rectangular microstrip loaded antenna is proposed. The obtained bandwidth of rectangular microstrip antenna is improved up to 46.92%. The proposed antenna has frequency band in the frequency range 1.979 GHz to 3.192 GHz this frequency band is suitable for WLAN / WiMAX and other wireless communication applications. The microstrip antenna suffers from narrow bandwidth hence the present work provide an alternative solution to increase the bandwidth. The gain has been improved up to 4.68dBi and antenna efficiency is 97.63%. The proposed slot loaded Microstrip antenna is fed by 0.3 mm line feed. The proposed antenna is simulated by IE3D Zealand simulation software based on method of moments.
2. ijece vibha raj_nag oct 12, 2017 edit septianIAESIJEECS
With advancement in communication technology over the past decade, there is an increasing demand for miniaturization, cost effective, multiband and wideband antennas. Dual band printed slot antenna designs can support in meeting these requirements. Various techniques, different shapes and geometries have been introduced for size reduction of dual band printed slot antennas. This paper is on various techniques for designing dual band printed slot antenna exhibits details of different geometries developed to get multiband behavior of printed slot antenna. In this paper geometry of the antenna and variousparameters such as return loss plot, gain plot, radiation pattern plot and VSWR plot are discussed. In this paper the review on various techniques of compactness by geometry on different shapes of printed slot antenna for 5G next generation wireless (NGW) mobile application are presented.
Magnetic resonance coupling for 5G WPT applicationsjournalBEEI
Inductive Wireless Power Transfer (IWPT) is the most popular and common technology for the resonance coupling power transfer. However, in 2007 it has experimentally demonstrated by a research group from Massachusets Institute of Technology (MIT) that WPT can be improved by using Magnetic Resonance Coupling Wireless Power Transfer (MRC WPT) in terms of the coupling distance and efficiency. Furthermore, by exploiting the unused, high-frequency mm-wave band which are ranging from 3~300 GHz frequency band, the next 5G generations of wireless networks will be able to support a higher number of devices with the increasing data rate, higher energy efficiency and also compatible with the previous technology. In this work, a square planar inductor with the dimension of 6.1 x 6.1 mm is designed, and the resonators have the same self-resonance frequency at 14 GHz. The coil resonators have been laid on Silicon and Oxide substrate to reduce the loss in the design. From the CST software simulation and the analytical model in MATLAB software, it has been shown that the MRC WPT design has improved the performance of IWPT design by 40% power transfer efficiency. MRC WPT design also has larger H-Field value which is 705.5 A/m, as compared to the IWPT design which has only 285.6 A/m when both Transmitter(Tx) and Reciever(RX) is at 0.3 mm coupling distance.
High gain 5G MIMO antenna for mobile base stationIJECEIAES
This article presented a millimeter wave antenna which operated at 38 GHz for 5G mobile base station. The MIMO (Multiple Input Multiple Output) antenna consisted of 1x10 linear array configurations. The proposed antenna’s size was 88 x 98 mm^2 and printed on 1.575 mm-thick Rogers Duroid 5880 subsrate with dielectric constant of ε_r= 2.2 and loss tangent (tanδ) of 0.0009. The antenna array covered along the azimuth plane to provide the coverage to the users in omnidirection. The simulated results showed that the single element antenna had the reflection coefficient (S11) of -59 dB, less than -10 dB in the frequency range of 35.5 - 39.6 GHz. More than 4.1 GHz of impedance bandwidth was obtained. The gain of the antenna linear array was 17.8 dBi while the suppression of the side lobes was -2.7 dB. It showed a high array gain throughout the impedance bandwidth with overall of VSWR were below 1.0646. It designed using CST microwave studio.
A miniaturized printed UWB antenna with dual notching for X-b and and aeronau...TELKOMNIKA JOURNAL
A low cost miniaturized UWB microstrip antenna with dual notched band for X band and aeronautical radio navigation (ARN) is presented in this article. The antenna (19 16×"> 25 mm2) is composed of a half-circular ring as a radiation patch with an incomplete ground plane. The measured results indicate a fractional bandwidth of 112% for 16S11≤-"> 10 dB between 3 to 10.6 GHz. The dual notched band has been achieved by incorporating window shaped microstrip closed ring resonators at the rear surface of the designed structure. The first notch band is centered at 7.5 GHz (7 8.1 GHz) to reject interference with X-band downlink (7.25 to 7.74 GHz) and second band centered at 9.1 GHz (8.6 9.4 GHz) to reject interference with aeronautical radio navigation (ARN) (8.7 to 9.2 GHz). The simulated and measured return loss, radiation pattern, and gain shows good agreement which confirms the applicability of the designed antenna for the intended UWB applications.
Design and Analysis of Broadband Elliptical Microstrip Patch Antenna for Wire...TELKOMNIKA JOURNAL
In this paper presents the design and manufacture of a new broadband elliptical patch antenna
with a microstrip feed line and optimum antenna parameters. The antenna dimension of
(30 × 21 × 1.6) 푚푚3 and fabricated on an FR-4 epoxy substrate having relative dielectric constant 휀푟=4.3,
loss tangent tan (δ)=0.002 and the feed line used has characteristic impedance of 50Ω.The designed
antenna has the capability of operating in the bandwidth (6.95-30.94) GHz and the gain (6.8) dBi. The
antenna performance was modified by inserting a slots in the ground plane to achieve impedance
bandwidth (when S11≤-10dB) and slots to patch to improve the gain. The modified antenna was designed
to be used for fifth generation (5G) mobile communication. The simulation results are obtained using CST
software.
The outgrowth of transportable wireless communication devices has pushed designers to design miniature size antennas. The most prized among miniature antenna selections is that the microstrip patch antenna. In this paper, A wideband M-shaped microstrip patch antenna has been designed for wireless communications such as Radar, Satellite and Microwave communications etc. A substrate of low dielectric constant named Rogers RT5880 is selected to obtain a compact radiating structure that meets the demanding bandwidth specification. The designed antenna has a dimension of 28.9mm by 24.20mm. The reflection coefficient at the input of the optimized M-shaped microstrip patch antenna is below −10 dB. The measurement results are in excellent agreement with the Sonnet Suite simulation results to analyze the performance. Simulation results show that the impedance bandwidth is 48.78% of the center frequency. This Method of Moment based simulation software provides the results in terms of S11 parameter, Return Loss, VSWR, etc. which is quite useful to analyze the antenna performance. The proposed microstrip patch antenna is suitable for C-band communication. The Bandwidth obtained for C-band communications is greater than other existing M-shape microstrip patch antennas.
WIDTH FEEDING STRIPLINE OPTIMISE OF CURVED MICROSTRIPLINE ARRAY VARIANS ANTEN...ijwmn
This study proposed to design of curved microstripline array antenna with more optimal characteristics
parametric through optimise in width feeding stripline and its application for radar communications.
Numeric analysis with an empirical formula in curved microstripline array antenna supports the counting in
relation to the characteristics antenna that is optimally applied in communications. The simulations was
created by using CST software. The result of simulation is to indicate Voltage Standing Wave Ratio (VSWR),
Reflection coefficient, Return Loss and Gain with Vertical Linear Polarization. The optimise of curved
microstripline array varians with the varians array and optimise varians in width of the feeding stripline.
Based on this simulated result, curved microstripline array varians antenna is potential to developed antenna
in radar communication in multiband frequency.
Wideband frequency reconfigurable metamaterial antenna design with double H s...journalBEEI
This paper presents the design of wideband frequency reconfigurable metamaterial antenna with double H slots. The design is based on the idea of composite right/left-handed transmission line (CRLH-TL) technique. Bandwidth enhancement was achieved by utilizing series left-handed capacitor CL transmission line parameter. The design has several outstanding advantages which include efficient bandwidth to cover many lower Application bands with multi frequency operation characteristics. A comprehensive analysis and simulation were done by using computer simulation technology (CST) software to determine the performance and efficiency of the proposed antenna. From the result obtained, the antenna aquired bandwidth range which covered (2.3-5.2) GHz which is equivalent to 77% fractional bandwidth. The wideband antenna was reconfigured by using frequency reconfiguration technique. From the reconfiguration results, the antenna can be switch from wideband to two single bands which resonate at 2.4 GHz and 4.2 GHz and to dual band which resonate at 2.4 GHz and 4.2 GHz. The realized peak gain at 2.4 GHz is 2.28 dBi and 2.58 dBi for E and H field respectively. The maximum efficiency of 96% was obtained. The antenna can be use for WLAN, proposed lower 5G band and cognitive radio system for frequency sencing.
Design and Analysis of Ku/K-band Circular SIW Patch Antenna Using 3D EM-based...TELKOMNIKA JOURNAL
Substrate Integrated Waveguide (SIW) antennas are considered as main radiators for RF and microwave wireless systems due to their low profile, low cost and soft integration with the other devices. The gain of a SIW patch antenna may be enhanced using different techniques such as Artificial Neural Networks (ANN) by modifying the antenna’s geometry with high efficiency comparing to electromagnetic techniques that take more time. This paper describes a novel structure of a circular SIW patch antenna design using a tree-dimensional electromagnetic (3D-EM) simulation based on ANN model which is developed as an accurate tool for synthesizing the forward side and then analyzing the reverse side of the problem. In this work, ANN algorithms are used for training the samples to provide precise geometrical dimensions of the SIW patch antenna with high accuracy for the target requirements. The antenna is designed to operate in Ku and K frequency bands, resonate at 16.10 GHz and 19.81 GHz respectively and show good performance resulting in low return losses of less than -10dB to -29dB for the selective frequency bands.
Millimeter-wave wireless technology (mmWave) has become a part of human life for fast and secure data transmission. This document introduces a 37GHz resonant frequency square microstrip patch antenna for mm Wave wireless communication. The antenna was designed and tested on a Rogers RT5880 board with a relative permittivity of 2.2 and a loss factor of 0.0009. Uses electromagnetic simulation software High Frequency Structure Simulator. The result of this paper shows minimal return loss -0.0812 dB, gain -1.205 dB, and impedance bandwidth 16.22% at 37 GHz resonant frequency. The voltage standing wave ratio (VSWR), radiation pattern has also presented for the proposed antenna which can be strong candidate for 5G mmWave cellular communication.
A 2.45 GHz microstrip antenna with harmonics suppression capability by using ...journalBEEI
In this work, a microstrip patch antenna with an inset feed and defected ground structure (DGS) is designed at the resonant frequency of 2.45 GHz. The antenna is designed on a FR-4 substrate with a dielectric constant, εr of 4.5, loss tangent, tan δ of 0.019 and thickness, h of 1.6 mm. The technique of DGS is used to avoid the use of additional circuits in the antenna to suppress the harmonics. By introducing a single and additional slots DGS at both ends on the antenna ground plane, the proposed microstrip patch antenna is able to suppress the higher order harmonics. The reflection coefficient, S11 is -38.75 dB at 2.45 GHz. The proposed antenna have suppressed the higher order harmonics effectively from -38.04 dB to -2.61 dB at 4.54 GHz and from -13.08 dB to -1.38 dB at 5.76 GHz. The prototype of the antenna is fabricated for the verification of the design. The simulated and measured results are found to be in a good agreement.
Design compact microstrap patch antenna with T-shaped 5G applicationjournalBEEI
This paper is presents a microstrap patch with a T-shaped rectangular antenna workings; the T-shaped patch operating at 3.6 GHz resonating frequency range for 5G application (from 2.9 to 4.4 GHz) repectively. The overall size of the proposed antenna is 22×24×0.25 mm3; the feeding technique using a 50 Ω feed line to the antenna. The proposed antenna is printed on compact Rogers RT 588 lz substrate having permittivity (ɛr) 2.00, loss tangent (tan δ) 0.0021, with thikness 0.2 mm. The proposed antenna introducesmany advantages like small size, low profile, and simpler structure. The characteristics such as radiation pattern, reflection coefficient, gain, current distribution, and radiation efficiency are respectively presented and discussed, using CST microwave study in simulating and analysing. Introducing a slot with a rectangular T-shaped patch antenna achieved lower frequency with 98.474% radiation efficiency and peak gain of the proposed antenna at 2.52 dB. The fractional bandwidth is 42.81% (2.90 GHz to 4.48 GHz) with a resonant frequency of 3.6 GHz and return loss at 28.76 dB. This frequency band attributessuited 5 G mobile application.
In this paper a compact, flexible, Multiband antenna is designed. It is having flexible Substrate of photographic paper which makes the antenna conformal. The antenna with two U slots cut in radiating patch is offset fed by microstrip lines gives the multiple bands of WLAN/WIMAX Application and two parasitic Elements improves the bandwidth of a typical microstrip antenna. The Measured results shows that the antenna resonates between Frequency band 2.10-2.95 GHz, 3.35-3.54 GHz and 5.04-6.0Hz.which are used for application such as Bluetooth, Wi-Fi, Zigbee, ISM 2.4GHz,WLAN WiMAX, and WLAN 5.2GHz.
5G Fixed Beam Switching on Microstrip Patch Antenna IJECEIAES
5G technology is using millimeter-wave band to improve the wireless communication system. However, narrow transmitter and receiver beams have caused the beam coverage area to be limited. Due to propagation limitations of mm wave band, beam forming technology with multi-beam based communication system, has been focused to overcome the problem. In this letter, a fixed beam switching method is introduced. By changing the switches, four different configurations of patch array antennas are designed to investigate their performances in terms of radiation patterns, beam forming angle, gain, half-power bandwidth and impedance bandwidth at 28 GHz operating frequency for 5G application. Mircostrip antenna is preferred due to its low profile, easy in feeding and array configurations. Three different beam directions had been formed at -15°, 0°, and 15° with half-power bandwidth of range 45˚ to 50˚.
In the present paper a circular slot rectangular microstrip loaded antenna is proposed. The obtained bandwidth of rectangular microstrip antenna is improved up to 46.92%. The proposed antenna has frequency band in the frequency range 1.979 GHz to 3.192 GHz this frequency band is suitable for WLAN / WiMAX and other wireless communication applications. The microstrip antenna suffers from narrow bandwidth hence the present work provide an alternative solution to increase the bandwidth. The gain has been improved up to 4.68dBi and antenna efficiency is 97.63%. The proposed slot loaded Microstrip antenna is fed by 0.3 mm line feed. The proposed antenna is simulated by IE3D Zealand simulation software based on method of moments.
2. ijece vibha raj_nag oct 12, 2017 edit septianIAESIJEECS
With advancement in communication technology over the past decade, there is an increasing demand for miniaturization, cost effective, multiband and wideband antennas. Dual band printed slot antenna designs can support in meeting these requirements. Various techniques, different shapes and geometries have been introduced for size reduction of dual band printed slot antennas. This paper is on various techniques for designing dual band printed slot antenna exhibits details of different geometries developed to get multiband behavior of printed slot antenna. In this paper geometry of the antenna and variousparameters such as return loss plot, gain plot, radiation pattern plot and VSWR plot are discussed. In this paper the review on various techniques of compactness by geometry on different shapes of printed slot antenna for 5G next generation wireless (NGW) mobile application are presented.
Magnetic resonance coupling for 5G WPT applicationsjournalBEEI
Inductive Wireless Power Transfer (IWPT) is the most popular and common technology for the resonance coupling power transfer. However, in 2007 it has experimentally demonstrated by a research group from Massachusets Institute of Technology (MIT) that WPT can be improved by using Magnetic Resonance Coupling Wireless Power Transfer (MRC WPT) in terms of the coupling distance and efficiency. Furthermore, by exploiting the unused, high-frequency mm-wave band which are ranging from 3~300 GHz frequency band, the next 5G generations of wireless networks will be able to support a higher number of devices with the increasing data rate, higher energy efficiency and also compatible with the previous technology. In this work, a square planar inductor with the dimension of 6.1 x 6.1 mm is designed, and the resonators have the same self-resonance frequency at 14 GHz. The coil resonators have been laid on Silicon and Oxide substrate to reduce the loss in the design. From the CST software simulation and the analytical model in MATLAB software, it has been shown that the MRC WPT design has improved the performance of IWPT design by 40% power transfer efficiency. MRC WPT design also has larger H-Field value which is 705.5 A/m, as compared to the IWPT design which has only 285.6 A/m when both Transmitter(Tx) and Reciever(RX) is at 0.3 mm coupling distance.
High gain 5G MIMO antenna for mobile base stationIJECEIAES
This article presented a millimeter wave antenna which operated at 38 GHz for 5G mobile base station. The MIMO (Multiple Input Multiple Output) antenna consisted of 1x10 linear array configurations. The proposed antenna’s size was 88 x 98 mm^2 and printed on 1.575 mm-thick Rogers Duroid 5880 subsrate with dielectric constant of ε_r= 2.2 and loss tangent (tanδ) of 0.0009. The antenna array covered along the azimuth plane to provide the coverage to the users in omnidirection. The simulated results showed that the single element antenna had the reflection coefficient (S11) of -59 dB, less than -10 dB in the frequency range of 35.5 - 39.6 GHz. More than 4.1 GHz of impedance bandwidth was obtained. The gain of the antenna linear array was 17.8 dBi while the suppression of the side lobes was -2.7 dB. It showed a high array gain throughout the impedance bandwidth with overall of VSWR were below 1.0646. It designed using CST microwave studio.
A miniaturized printed UWB antenna with dual notching for X-b and and aeronau...TELKOMNIKA JOURNAL
A low cost miniaturized UWB microstrip antenna with dual notched band for X band and aeronautical radio navigation (ARN) is presented in this article. The antenna (19 16×"> 25 mm2) is composed of a half-circular ring as a radiation patch with an incomplete ground plane. The measured results indicate a fractional bandwidth of 112% for 16S11≤-"> 10 dB between 3 to 10.6 GHz. The dual notched band has been achieved by incorporating window shaped microstrip closed ring resonators at the rear surface of the designed structure. The first notch band is centered at 7.5 GHz (7 8.1 GHz) to reject interference with X-band downlink (7.25 to 7.74 GHz) and second band centered at 9.1 GHz (8.6 9.4 GHz) to reject interference with aeronautical radio navigation (ARN) (8.7 to 9.2 GHz). The simulated and measured return loss, radiation pattern, and gain shows good agreement which confirms the applicability of the designed antenna for the intended UWB applications.
Design and Analysis of Broadband Elliptical Microstrip Patch Antenna for Wire...TELKOMNIKA JOURNAL
In this paper presents the design and manufacture of a new broadband elliptical patch antenna
with a microstrip feed line and optimum antenna parameters. The antenna dimension of
(30 × 21 × 1.6) 푚푚3 and fabricated on an FR-4 epoxy substrate having relative dielectric constant 휀푟=4.3,
loss tangent tan (δ)=0.002 and the feed line used has characteristic impedance of 50Ω.The designed
antenna has the capability of operating in the bandwidth (6.95-30.94) GHz and the gain (6.8) dBi. The
antenna performance was modified by inserting a slots in the ground plane to achieve impedance
bandwidth (when S11≤-10dB) and slots to patch to improve the gain. The modified antenna was designed
to be used for fifth generation (5G) mobile communication. The simulation results are obtained using CST
software.
The outgrowth of transportable wireless communication devices has pushed designers to design miniature size antennas. The most prized among miniature antenna selections is that the microstrip patch antenna. In this paper, A wideband M-shaped microstrip patch antenna has been designed for wireless communications such as Radar, Satellite and Microwave communications etc. A substrate of low dielectric constant named Rogers RT5880 is selected to obtain a compact radiating structure that meets the demanding bandwidth specification. The designed antenna has a dimension of 28.9mm by 24.20mm. The reflection coefficient at the input of the optimized M-shaped microstrip patch antenna is below −10 dB. The measurement results are in excellent agreement with the Sonnet Suite simulation results to analyze the performance. Simulation results show that the impedance bandwidth is 48.78% of the center frequency. This Method of Moment based simulation software provides the results in terms of S11 parameter, Return Loss, VSWR, etc. which is quite useful to analyze the antenna performance. The proposed microstrip patch antenna is suitable for C-band communication. The Bandwidth obtained for C-band communications is greater than other existing M-shape microstrip patch antennas.
WIDTH FEEDING STRIPLINE OPTIMISE OF CURVED MICROSTRIPLINE ARRAY VARIANS ANTEN...ijwmn
This study proposed to design of curved microstripline array antenna with more optimal characteristics
parametric through optimise in width feeding stripline and its application for radar communications.
Numeric analysis with an empirical formula in curved microstripline array antenna supports the counting in
relation to the characteristics antenna that is optimally applied in communications. The simulations was
created by using CST software. The result of simulation is to indicate Voltage Standing Wave Ratio (VSWR),
Reflection coefficient, Return Loss and Gain with Vertical Linear Polarization. The optimise of curved
microstripline array varians with the varians array and optimise varians in width of the feeding stripline.
Based on this simulated result, curved microstripline array varians antenna is potential to developed antenna
in radar communication in multiband frequency.
Wideband frequency reconfigurable metamaterial antenna design with double H s...journalBEEI
This paper presents the design of wideband frequency reconfigurable metamaterial antenna with double H slots. The design is based on the idea of composite right/left-handed transmission line (CRLH-TL) technique. Bandwidth enhancement was achieved by utilizing series left-handed capacitor CL transmission line parameter. The design has several outstanding advantages which include efficient bandwidth to cover many lower Application bands with multi frequency operation characteristics. A comprehensive analysis and simulation were done by using computer simulation technology (CST) software to determine the performance and efficiency of the proposed antenna. From the result obtained, the antenna aquired bandwidth range which covered (2.3-5.2) GHz which is equivalent to 77% fractional bandwidth. The wideband antenna was reconfigured by using frequency reconfiguration technique. From the reconfiguration results, the antenna can be switch from wideband to two single bands which resonate at 2.4 GHz and 4.2 GHz and to dual band which resonate at 2.4 GHz and 4.2 GHz. The realized peak gain at 2.4 GHz is 2.28 dBi and 2.58 dBi for E and H field respectively. The maximum efficiency of 96% was obtained. The antenna can be use for WLAN, proposed lower 5G band and cognitive radio system for frequency sencing.
Design and Analysis of Ku/K-band Circular SIW Patch Antenna Using 3D EM-based...TELKOMNIKA JOURNAL
Substrate Integrated Waveguide (SIW) antennas are considered as main radiators for RF and microwave wireless systems due to their low profile, low cost and soft integration with the other devices. The gain of a SIW patch antenna may be enhanced using different techniques such as Artificial Neural Networks (ANN) by modifying the antenna’s geometry with high efficiency comparing to electromagnetic techniques that take more time. This paper describes a novel structure of a circular SIW patch antenna design using a tree-dimensional electromagnetic (3D-EM) simulation based on ANN model which is developed as an accurate tool for synthesizing the forward side and then analyzing the reverse side of the problem. In this work, ANN algorithms are used for training the samples to provide precise geometrical dimensions of the SIW patch antenna with high accuracy for the target requirements. The antenna is designed to operate in Ku and K frequency bands, resonate at 16.10 GHz and 19.81 GHz respectively and show good performance resulting in low return losses of less than -10dB to -29dB for the selective frequency bands.
Millimeter-wave wireless technology (mmWave) has become a part of human life for fast and secure data transmission. This document introduces a 37GHz resonant frequency square microstrip patch antenna for mm Wave wireless communication. The antenna was designed and tested on a Rogers RT5880 board with a relative permittivity of 2.2 and a loss factor of 0.0009. Uses electromagnetic simulation software High Frequency Structure Simulator. The result of this paper shows minimal return loss -0.0812 dB, gain -1.205 dB, and impedance bandwidth 16.22% at 37 GHz resonant frequency. The voltage standing wave ratio (VSWR), radiation pattern has also presented for the proposed antenna which can be strong candidate for 5G mmWave cellular communication.
A 2.45 GHz microstrip antenna with harmonics suppression capability by using ...journalBEEI
In this work, a microstrip patch antenna with an inset feed and defected ground structure (DGS) is designed at the resonant frequency of 2.45 GHz. The antenna is designed on a FR-4 substrate with a dielectric constant, εr of 4.5, loss tangent, tan δ of 0.019 and thickness, h of 1.6 mm. The technique of DGS is used to avoid the use of additional circuits in the antenna to suppress the harmonics. By introducing a single and additional slots DGS at both ends on the antenna ground plane, the proposed microstrip patch antenna is able to suppress the higher order harmonics. The reflection coefficient, S11 is -38.75 dB at 2.45 GHz. The proposed antenna have suppressed the higher order harmonics effectively from -38.04 dB to -2.61 dB at 4.54 GHz and from -13.08 dB to -1.38 dB at 5.76 GHz. The prototype of the antenna is fabricated for the verification of the design. The simulated and measured results are found to be in a good agreement.
Multiband Circular Microstrip Patch Antenna for WLAN Applicationtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
Analysis and Design of S-shaped Microstrip Patch AntennaIOSR Journals
Abstract: This paper gives a compact analysis and design of S-shaped Microstrip patch antenna which is best suited for Wi-max application. The analysis and design is simulated over IE3D software Ver. 15.2. We have taken a definite ground plane of 50x70 mm and patch size of 30x50 mm.The substrate thickness is taken as 1.6 mm and dielectric constant of 4.2 and loss tangent of 0.0013. The simulated result shows that the bandwidth is obtained in triple band- 7.79% at 0.262921 GHz band, 13.45% at 1.53034 GHz band and 28.0056% at 2.2382 GHz band. The obtained gain is 3.96 dBi at 2.33945 GHz. The obtained gain and bandwidth is best suited for Wi-max application. Keywords: S shape, Ground plane, Patch Antenna, Triple Band.
Design and characterization of frequency reconfigurable honey bee antenna fo...IJECEIAES
In this article, a frequency reconfigurable honey-bee compact microstrip monopole antenna is proposed which is fed by a microstrip line (50 Ω) having the capability of providing dual-band as well as triple-band operation in eight distinct modes. By embedding three PIN diodes overs the honey bee arms, the effective current distribution is controlled hence resonant frequency is also changed in eight distinct modes in real-time. This is the reason the proposed antenna is portrayed as a frequency reconfigurable antenna in this paper which is suitable for cognitive radio application. This proposed antenna can be used for various wireless application such as Bluetooth, Wi-Fi, worldwide interoperability for microwave access (WiMAX), wireless local area network (WLAN), C-band, and X-band applications. The proposed antenna possesses a planner geometry of 39×34×0.87 mm3 which is printed on a substrate as flexible FR-4 (lossy) (εr=4.4 and tanδ=0.019). The proposed antenna exhibits voltage standing wave ratio (VSWR)<2 for all 19 resonant frequencies of interest and perceptible radiation pattern over entire frequency bands with a positive gain. CST microwave studio is used to find out all simulated results of antenna parameters.
A new miniaturized wideband self-isolated two-port MIMO antenna for 5G millim...TELKOMNIKA JOURNAL
Nowadays, millimeter-wave frequencies present a catchy solution to securing the colossal data rate needed for 5G communications. Accordingly, this research deals with the conception of a novel orthogonal 2×2 multiple input, multiple output (MIMO) antenna design operating in the millimeter wave spectrum with quite small dimensions of 11×6×0.8 mm3. The single antenna element consists of a trapezoidal microstrip patch antenna built on the Rogers RT5880 laminate with a permittivity of 2.2 and tangent loss of 0.0009. A trapezoidal-slot ground plane is used to support the structure. The antenna resonates at 28 GHz with a large bandwidth of 4 GHz from 26 to 30 GHz, a good gain of up to 5 dB, and a high radiation efficiency of 99%. A strong isolation is achieved that surpasses 26 dB. Besides, a high diversity performance is achieved where the envelope correlation coefficient (ECC) is lower than 0.001, the diversity gain (DG) is greater than 10 dB, and the channel capacity loss (CCL) is no longer than 0.4 bit/s/Hz. The achieved outcomes prove the robustness of the suggested MIMO antenna and qualify it to be a strong candidate for 5G wireless devices.
Design of Rectangular Microstrip Antenna with Finite Ground Plane for WI-FI, ...ijsrd.com
Microstrip antennas are suitable for mobile and satellite communication systems. This is particularly due to their main characteristics such as low volume and weight, as well as because they are easy to fabricate and to be installed on plane and curved surfaces. Nevertheless these antennas present some disadvantages like narrow bandwidth, low power operation, and radiation loss. There are some methods such as increasing the height of the substrate, which can be used to extend the efficiency and bandwidth. In this communication design and performance of a novel rectangular with finite ground is proposed to achieve wide band performance and circular polarization. “The proposed structure consists of a rectangular patch and the ground planâ€Â
Design of CPW-fed Capacitive Coupled Patch Antenna for WiGig Applicationsinventy
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Design and Analysis of MIMO Patch Antenna for 5G Wireless Communication SystemsIJCNCJournal
In this work, the circular array microstrip patch antenna (MPA) design is proposed for the 5G wireless communication and the millimeter- wave frequency being utilized for this communication system to enhance the coverage area. Here, the Multi Input Multi Output feeding technique is utilized to improve the performance of the proposed design at a resonant frequency of 35 GHz with RT-Duroid 5880 material as substrate. It has 2.2 dielectric constant value and the thickness is 0.5mm.The simulation analysis has obtained the gain as 8.8dB and return loss as -41.9dB. Also, two MPA designs such as single element MPA and 2x2 rectangular array MPA are designed to validate the proposed antenna design. A comparative analysis has proved that the circular array MPA is preferable for the 5G wireless communication system compared to the other two designs such as single element MPA and 2x2 rectangular array MPA.
DESIGN AND ANALYSIS OF MIMO PATCH ANTENNA FOR 5G WIRELESS COMMUNICATION SYSTEMSIJCNCJournal
In this work, the circular array microstrip patch antenna (MPA) design is proposed for the 5G wireless
communication and the millimeter- wave frequency being utilized for this communication system to
enhance the coverage area. Here, the Multi Input Multi Output feeding technique is utilized to improve the
performance of the proposed design at a resonant frequency of 35 GHz with RT-Duroid 5880 material as
substrate. It has 2.2 dielectric constant value and the thickness is 0.5mm.The simulation analysis has
obtained the gain as 8.8dB and return loss as -41.9dB. Also, two MPA designs such as single element MPA
and 2x2 rectangular array MPA are designed to validate the proposed antenna design. A comparative
analysis has proved that the circular array MPA is preferable for the 5G wireless communication system
compared to the other two designs such as single element MPA and 2x2 rectangular array MPA.
Microstrip Rectangular Monopole Antennas with Defected Ground for UWB Applica...IJECEIAES
This paper presents the design of new compact antennas for ultra wide band applications. Each antenna consists of a rectangular patch fed by 50Ω microstrip transmission line and the ground element is a defected ground structure (DGS). The aim of this study is to improve the bandwidth of these antennas by using DGS and the modification geometry of rectangular structure, which gives new compact antennas for UWB applications. The input impedance bandwidth of the antennas with S11<-10dB is more than 10GHz, from 3GHz to more than 14 GHz. The proposed antennas are investigated and optimized by using CST microwave studio, they are validated by using another electromagnetic solver Ansoft HFSS. The measured parameters present good agreement with simulation. The final antenna structures offer excellent performances for UWB system.
A Compact Wideband Monopole Antenna using Single Open Loop Resonator for Wire...TELKOMNIKA JOURNAL
A novel single layer, microstrip line fed compact wideband monopole antenna using open loop resonator has been designed and analyzed. The proposed antenna occupies a compact size of only 30 36.5 1.6 mm3. A partial ground plane is employed to enhance the operating bandwidth and reflection coefficient of the proposed antenna. The variations in operating bandwidth of the proposed antenna can be easily controlled by properly adjusting the position of the gap in the open loop resonator.The antenna prototype is fabricated on FR4 substrate with a dielectric constant 4.2. In this design, the antenna exhibits 10dB wide impedance bandwidth of 61% from 2.0174 to 3.7903 GHz.The antenna can be easily fed using a 50 Ω microstrip feed line and it covers the bandwidth requirements of a number of modern wireless communication systems such as IEEE 502.11b WLAN band (2.4 2.5 GHz), extended UMTS (2.5 2.69 GHz), IMT (2.7 2.9 GHz), and IEEE 802.16 Wi MAX band (3.3 3.6 GHz) applications. The desired antenna is designed and simulated using Computer Simulation Technology (CST). An extensive analysis of the antenna parameters (reflection coefficient, radiation pattern, directivity, and VSWR) including surface current distributions is presented and discussed in this paper. Good agreement between simulated and measured result is obtained.
In this paper, a novel multi-frequency microstrip antenna with complementary ring slot resonator (CRSR) structure that satisfies Bluetooth, worldwide interoperability for microwave access (WiMAX), and wireless local area network (WLAN) applications is proposed. The conventional antenna consists of a circular microstrip patch at a resonance frequency band of 2.5 GHz. By loading two CRSR at the radiating element, three operating frequency bands 2.5 GHz, 3.6 GHz, and 5.2 GHz are achieved. The operational bands covered by the antenna are Bluetooth 2.5 GHz, WiMAX 3.6 GHz, and WLAN 5.2 GHz. The insertion of CRSR to patch antenna has made it possible to compact and simple design, and miniaturized antenna for cognitive radio. Moreover, the directivity of the proposed antenna is adequate with acceptable radiation properties and perfectly matches with the simulated and measured results.
TRI-BAND MICROSTRIP PATCH ANTENNA FOR S-BAND NANO SATELLITE APPLICATION USING...ijsrd.com
It's the generation of tiny satellites which basically needs all its components to be miniature. The product proposed here is one such component, a tri band micro strip patch antenna operating at 2.6GHz, 3.6GHz S-band frequencies and 5.8 GHz. This real-time project work deals with a rectangular patch antenna operating at different frequencies working for various applications. The proposed S-Band Patch antenna is being designed and simulated using HFSS software. Obtaining optimum bandwidth efficiency by choosing suitable size without affecting any other parameters of the antenna is the challenge taken over in this project. The low profile, less weight patch antenna has antenna element of physical dimension 40x40x2.6mm .The substrate material being used is Alumina with dielectric constant 9.6. This antenna is designed to be used for TTC and payload downlink purposes. The designed patch array antenna meets all the parametric needs for a Polar orbiting satellite at Low Earth Orbit (LEO) region.
Ultra-Wideband Monostatic Antenna for behind the Wall Detection IJECEIAES
This article introduces an ultra-wideband (UWB) shifted arc antenna, designed using Rogers RT-5880 Duroid substrate for the human detection behind the wall. The frequency for this proposed antenna ranges from 2.8 - 15.6GHz with the gain of around 6.05dB. A high gain for antenna has been achieved by the implementation of defected ground structure (DGS) method to make it a suitable configuration for through wall detection applications. For the verification of through wall detection configuration, a simulation-based experiment using ground penetrating radar (GPR) technology has been conducted. The results showed that proposed single antenna can act as a monostatic transceiver in order to detect human skin behind the concrete wall. Later, the reflections received from the target have been analyzed to detect and identify the antenna, wall and target for distance calculation.
Rectangular and circular antennas design for Bluetooth applicationsTELKOMNIKA JOURNAL
The most researched and examined aspect of the communication system is the wireless connection. Without learning how to operate and use different types of antennas, your knowledge is incomplete. Microstrip patch antenna research has advanced significantly in recent years. When compared to standard antennas, microstrip patch antennas provide additional advantages and opportunities. It is of low volume, light weight, low cost, low appearance, compact and easy to manufacture. This study investigates the differences between rectangular and circular patch antennas. For Bluetooth applications, the center frequency of 2.4 GHz was chosen as the optimal resonant frequency. On a flame retardant (FR-4) epoxy substrate, the antenna dielectric constant is 4.4. Above the ground the base rises 3.6 mm. For the simulation process, high frequency simulation software (HFSS 15) is used as the program design. Antennas 1×1, 1×2, and 1×4 are designed for both circular and rectangular antennas. A comparison was made for both types of antennas and voltage standing wave ratio (VSWR), return losses, gain, directivity and half power beam width (HPBW) were found, and the feature of the rectangular antenna was shown.
Multiband antenna using stacked series array for Ka-Band applicationjournalBEEI
In this paper, a multiband stack series array antenna is designed in order to attain solutions for the future 28 GHz Ka-band application. Double layer substrate Technology is utilized to accomplish multiple resonant frequencies with higher data transfer capacities due to high bandwidth. The designed antenna is dependent on twofold layer consisting patches and resonators in different layers stacked together. The designed multiband antennas can resonate at single band of
(28 GHz), dual band of (28 and 30 GHz) and triple band of (24.18, 26 and 28.453). The results achieved in the simulation are later fabricated and tested. The test result illustrates that the antennas have wide bandwidth, high gain and even higher efficiencies. All the proposed antenna configurations have demonstrated a decent possibility for 5G millimeter wave (mmwave) application.
Similar to Substrate integrate waveguide and microstrip antennas at 28 GHz (20)
Square transposition: an approach to the transposition process in block cipherjournalBEEI
The transposition process is needed in cryptography to create a diffusion effect on data encryption standard (DES) and advanced encryption standard (AES) algorithms as standard information security algorithms by the National Institute of Standards and Technology. The problem with DES and AES algorithms is that their transposition index values form patterns and do not form random values. This condition will certainly make it easier for a cryptanalyst to look for a relationship between ciphertexts because some processes are predictable. This research designs a transposition algorithm called square transposition. Each process uses square 8 × 8 as a place to insert and retrieve 64-bits. The determination of the pairing of the input scheme and the retrieval scheme that have unequal flow is an important factor in producing a good transposition. The square transposition can generate random and non-pattern indices so that transposition can be done better than DES and AES.
Hyper-parameter optimization of convolutional neural network based on particl...journalBEEI
Deep neural networks have accomplished enormous progress in tackling many problems. More specifically, convolutional neural network (CNN) is a category of deep networks that have been a dominant technique in computer vision tasks. Despite that these deep neural networks are highly effective; the ideal structure is still an issue that needs a lot of investigation. Deep Convolutional Neural Network model is usually designed manually by trials and repeated tests which enormously constrain its application. Many hyper-parameters of the CNN can affect the model performance. These parameters are depth of the network, numbers of convolutional layers, and numbers of kernels with their sizes. Therefore, it may be a huge challenge to design an appropriate CNN model that uses optimized hyper-parameters and reduces the reliance on manual involvement and domain expertise. In this paper, a design architecture method for CNNs is proposed by utilization of particle swarm optimization (PSO) algorithm to learn the optimal CNN hyper-parameters values. In the experiment, we used Modified National Institute of Standards and Technology (MNIST) database of handwritten digit recognition. The experiments showed that our proposed approach can find an architecture that is competitive to the state-of-the-art models with a testing error of 0.87%.
Supervised machine learning based liver disease prediction approach with LASS...journalBEEI
In this contemporary era, the uses of machine learning techniques are increasing rapidly in the field of medical science for detecting various diseases such as liver disease (LD). Around the globe, a large number of people die because of this deadly disease. By diagnosing the disease in a primary stage, early treatment can be helpful to cure the patient. In this research paper, a method is proposed to diagnose the LD using supervised machine learning classification algorithms, namely logistic regression, decision tree, random forest, AdaBoost, KNN, linear discriminant analysis, gradient boosting and support vector machine (SVM). We also deployed a least absolute shrinkage and selection operator (LASSO) feature selection technique on our taken dataset to suggest the most highly correlated attributes of LD. The predictions with 10 fold cross-validation (CV) made by the algorithms are tested in terms of accuracy, sensitivity, precision and f1-score values to forecast the disease. It is observed that the decision tree algorithm has the best performance score where accuracy, precision, sensitivity and f1-score values are 94.295%, 92%, 99% and 96% respectively with the inclusion of LASSO. Furthermore, a comparison with recent studies is shown to prove the significance of the proposed system.
A secure and energy saving protocol for wireless sensor networksjournalBEEI
The research domain for wireless sensor networks (WSN) has been extensively conducted due to innovative technologies and research directions that have come up addressing the usability of WSN under various schemes. This domain permits dependable tracking of a diversity of environments for both military and civil applications. The key management mechanism is a primary protocol for keeping the privacy and confidentiality of the data transmitted among different sensor nodes in WSNs. Since node's size is small; they are intrinsically limited by inadequate resources such as battery life-time and memory capacity. The proposed secure and energy saving protocol (SESP) for wireless sensor networks) has a significant impact on the overall network life-time and energy dissipation. To encrypt sent messsages, the SESP uses the public-key cryptography’s concept. It depends on sensor nodes' identities (IDs) to prevent the messages repeated; making security goals- authentication, confidentiality, integrity, availability, and freshness to be achieved. Finally, simulation results show that the proposed approach produced better energy consumption and network life-time compared to LEACH protocol; sensors are dead after 900 rounds in the proposed SESP protocol. While, in the low-energy adaptive clustering hierarchy (LEACH) scheme, the sensors are dead after 750 rounds.
Plant leaf identification system using convolutional neural networkjournalBEEI
This paper proposes a leaf identification system using convolutional neural network (CNN). This proposed system can identify five types of local Malaysia leaf which were acacia, papaya, cherry, mango and rambutan. By using CNN from deep learning, the network is trained from the database that acquired from leaf images captured by mobile phone for image classification. ResNet-50 was the architecture has been used for neural networks image classification and training the network for leaf identification. The recognition of photographs leaves requested several numbers of steps, starting with image pre-processing, feature extraction, plant identification, matching and testing, and finally extracting the results achieved in MATLAB. Testing sets of the system consists of 3 types of images which were white background, and noise added and random background images. Finally, interfaces for the leaf identification system have developed as the end software product using MATLAB app designer. As a result, the accuracy achieved for each training sets on five leaf classes are recorded above 98%, thus recognition process was successfully implemented.
Customized moodle-based learning management system for socially disadvantaged...journalBEEI
This study aims to develop Moodle-based LMS with customized learning content and modified user interface to facilitate pedagogical processes during covid-19 pandemic and investigate how teachers of socially disadvantaged schools perceived usability and technology acceptance. Co-design process was conducted with two activities: 1) need assessment phase using an online survey and interview session with the teachers and 2) the development phase of the LMS. The system was evaluated by 30 teachers from socially disadvantaged schools for relevance to their distance learning activities. We employed computer software usability questionnaire (CSUQ) to measure perceived usability and the technology acceptance model (TAM) with insertion of 3 original variables (i.e., perceived usefulness, perceived ease of use, and intention to use) and 5 external variables (i.e., attitude toward the system, perceived interaction, self-efficacy, user interface design, and course design). The average CSUQ rating exceeded 5.0 of 7 point-scale, indicated that teachers agreed that the information quality, interaction quality, and user interface quality were clear and easy to understand. TAM results concluded that the LMS design was judged to be usable, interactive, and well-developed. Teachers reported an effective user interface that allows effective teaching operations and lead to the system adoption in immediate time.
Understanding the role of individual learner in adaptive and personalized e-l...journalBEEI
Dynamic learning environment has emerged as a powerful platform in a modern e-learning system. The learning situation that constantly changing has forced the learning platform to adapt and personalize its learning resources for students. Evidence suggested that adaptation and personalization of e-learning systems (APLS) can be achieved by utilizing learner modeling, domain modeling, and instructional modeling. In the literature of APLS, questions have been raised about the role of individual characteristics that are relevant for adaptation. With several options, a new problem has been raised where the attributes of students in APLS often overlap and are not related between studies. Therefore, this study proposed a list of learner model attributes in dynamic learning to support adaptation and personalization. The study was conducted by exploring concepts from the literature selected based on the best criteria. Then, we described the results of important concepts in student modeling and provided definitions and examples of data values that researchers have used. Besides, we also discussed the implementation of the selected learner model in providing adaptation in dynamic learning.
Prototype mobile contactless transaction system in traditional markets to sup...journalBEEI
One way to prevent and reduce the spread of the covid-19 pandemic is through physical distancing program. This research aims to develop a prototype contactless transaction system using digital payment mechanisms and QR code technology that will be applied in traditional markets. The method used in the development of electronic market systems is a prototype approach. The application of QR code and digital payments are used as a solution to minimize money exchange contacts that are common in traditional markets. The results showed that the system built was able to accelerate and facilitate the buying and selling transaction process in traditional market environment. Alpha testing shows that all functional systems are running well. Meanwhile, beta testing shows that the user can very well accept the system that was built. The results of the study also show acceptance of the usefulness of the system being built, as well as the optimism of its users to be able to take advantage of this system both technologically and functionally, so its can be a part of the digital transformation of the traditional market to the electronic market and has become one of the solutions in reducing the spread of the current covid-19 pandemic.
Wireless HART stack using multiprocessor technique with laxity algorithmjournalBEEI
The use of a real-time operating system is required for the demarcation of industrial wireless sensor network (IWSN) stacks (RTOS). In the industrial world, a vast number of sensors are utilised to gather various types of data. The data gathered by the sensors cannot be prioritised ahead of time. Because all of the information is equally essential. As a result, a protocol stack is employed to guarantee that data is acquired and processed fairly. In IWSN, the protocol stack is implemented using RTOS. The data collected from IWSN sensor nodes is processed using non-preemptive scheduling and the protocol stack, and then sent in parallel to the IWSN's central controller. The real-time operating system (RTOS) is a process that occurs between hardware and software. Packets must be sent at a certain time. It's possible that some packets may collide during transmission. We're going to undertake this project to get around this collision. As a prototype, this project is divided into two parts. The first uses RTOS and the LPC2148 as a master node, while the second serves as a standard data collection node to which sensors are attached. Any controller may be used in the second part, depending on the situation. Wireless HART allows two nodes to communicate with each other.
Implementation of double-layer loaded on octagon microstrip yagi antennajournalBEEI
A double-layer loaded on the octagon microstrip yagi antenna (OMYA) at 5.8 GHz industrial, scientific and medical (ISM) Band is investigated in this paper. The double-layer consist of two double positive (DPS) substrates. The OMYA is overlaid with a double-layer configuration were simulated, fabricated and measured. A good agreement was observed between the computed and measured results of the gain for this antenna. According to comparison results, it shows that 2.5 dB improvement of the OMYA gain can be obtained by applying the double-layer on the top of the OMYA. Meanwhile, the bandwidth of the measured OMYA with the double-layer is 14.6%. It indicates that the double-layer can be used to increase the OMYA performance in term of gain and bandwidth.
The calculation of the field of an antenna located near the human headjournalBEEI
In this work, a numerical calculation was carried out in one of the universal programs for automatic electro-dynamic design. The calculation is aimed at obtaining numerical values for specific absorbed power (SAR). It is the SAR value that can be used to determine the effect of the antenna of a wireless device on biological objects; the dipole parameters will be selected for GSM1800. Investigation of the influence of distance to a cell phone on radiation shows that absorbed in the head of a person the effect of electromagnetic radiation on the brain decreases by three times this is a very important result the SAR value has decreased by almost three times it is acceptable results.
Exact secure outage probability performance of uplinkdownlink multiple access...journalBEEI
In this paper, we study uplink-downlink non-orthogonal multiple access (NOMA) systems by considering the secure performance at the physical layer. In the considered system model, the base station acts a relay to allow two users at the left side communicate with two users at the right side. By considering imperfect channel state information (CSI), the secure performance need be studied since an eavesdropper wants to overhear signals processed at the downlink. To provide secure performance metric, we derive exact expressions of secrecy outage probability (SOP) and and evaluating the impacts of main parameters on SOP metric. The important finding is that we can achieve the higher secrecy performance at high signal to noise ratio (SNR). Moreover, the numerical results demonstrate that the SOP tends to a constant at high SNR. Finally, our results show that the power allocation factors, target rates are main factors affecting to the secrecy performance of considered uplink-downlink NOMA systems.
Design of a dual-band antenna for energy harvesting applicationjournalBEEI
This report presents an investigation on how to improve the current dual-band antenna to enhance the better result of the antenna parameters for energy harvesting application. Besides that, to develop a new design and validate the antenna frequencies that will operate at 2.4 GHz and 5.4 GHz. At 5.4 GHz, more data can be transmitted compare to 2.4 GHz. However, 2.4 GHz has long distance of radiation, so it can be used when far away from the antenna module compare to 5 GHz that has short distance in radiation. The development of this project includes the scope of designing and testing of antenna using computer simulation technology (CST) 2018 software and vector network analyzer (VNA) equipment. In the process of designing, fundamental parameters of antenna are being measured and validated, in purpose to identify the better antenna performance.
Transforming data-centric eXtensible markup language into relational database...journalBEEI
eXtensible markup language (XML) appeared internationally as the format for data representation over the web. Yet, most organizations are still utilising relational databases as their database solutions. As such, it is crucial to provide seamless integration via effective transformation between these database infrastructures. In this paper, we propose XML-REG to bridge these two technologies based on node-based and path-based approaches. The node-based approach is good to annotate each positional node uniquely, while the path-based approach provides summarised path information to join the nodes. On top of that, a new range labelling is also proposed to annotate nodes uniquely by ensuring the structural relationships are maintained between nodes. If a new node is to be added to the document, re-labelling is not required as the new label will be assigned to the node via the new proposed labelling scheme. Experimental evaluations indicated that the performance of XML-REG exceeded XMap, XRecursive, XAncestor and Mini-XML concerning storing time, query retrieval time and scalability. This research produces a core framework for XML to relational databases (RDB) mapping, which could be adopted in various industries.
Key performance requirement of future next wireless networks (6G)journalBEEI
Given the massive potentials of 5G communication networks and their foreseeable evolution, what should there be in 6G that is not in 5G or its long-term evolution? 6G communication networks are estimated to integrate the terrestrial, aerial, and maritime communications into a forceful network which would be faster, more reliable, and can support a massive number of devices with ultra-low latency requirements. This article presents a complete overview of potential 6G communication networks. The major contribution of this study is to present a broad overview of key performance indicators (KPIs) of 6G networks that cover the latest manufacturing progress in the environment of the principal areas of research application, and challenges.
Noise resistance territorial intensity-based optical flow using inverse confi...journalBEEI
This paper presents the use of the inverse confidential technique on bilateral function with the territorial intensity-based optical flow to prove the effectiveness in noise resistance environment. In general, the image’s motion vector is coded by the technique called optical flow where the sequences of the image are used to determine the motion vector. But, the accuracy rate of the motion vector is reduced when the source of image sequences is interfered by noises. This work proved that the inverse confidential technique on bilateral function can increase the percentage of accuracy in the motion vector determination by the territorial intensity-based optical flow under the noisy environment. We performed the testing with several kinds of non-Gaussian noises at several patterns of standard image sequences by analyzing the result of the motion vector in a form of the error vector magnitude (EVM) and compared it with several noise resistance techniques in territorial intensity-based optical flow method.
Modeling climate phenomenon with software grids analysis and display system i...journalBEEI
This study aims to model climate change based on rainfall, air temperature, pressure, humidity and wind with grADS software and create a global warming module. This research uses 3D model, define, design, and develop. The results of the modeling of the five climate elements consist of the annual average temperature in Indonesia in 2009-2015 which is between 29oC to 30.1oC, the horizontal distribution of the annual average pressure in Indonesia in 2009-2018 is between 800 mBar to 1000 mBar, the horizontal distribution the average annual humidity in Indonesia in 2009 and 2011 ranged between 27-57, in 2012-2015, 2017 and 2018 it ranged between 30-60, during the East Monsoon, the wind circulation moved from northern Indonesia to the southern region Indonesia. During the west monsoon, the wind circulation moves from the southern part of Indonesia to the northern part of Indonesia. The global warming module for SMA/MA produced is feasible to use, this is in accordance with the value given by the validate of 69 which is in the appropriate category and the response of teachers and students through a 91% questionnaire.
An approach of re-organizing input dataset to enhance the quality of emotion ...journalBEEI
The purpose of this paper is to propose an approach of re-organizing input data to recognize emotion based on short signal segments and increase the quality of emotional recognition using physiological signals. MIT's long physiological signal set was divided into two new datasets, with shorter and overlapped segments. Three different classification methods (support vector machine, random forest, and multilayer perceptron) were implemented to identify eight emotional states based on statistical features of each segment in these two datasets. By re-organizing the input dataset, the quality of recognition results was enhanced. The random forest shows the best classification result among three implemented classification methods, with an accuracy of 97.72% for eight emotional states, on the overlapped dataset. This approach shows that, by re-organizing the input dataset, the high accuracy of recognition results can be achieved without the use of EEG and ECG signals.
Parking detection system using background subtraction and HSV color segmentationjournalBEEI
Manual system vehicle parking makes finding vacant parking lots difficult, so it has to check directly to the vacant space. If many people do parking, then the time needed for it is very much or requires many people to handle it. This research develops a real-time parking system to detect parking. The system is designed using the HSV color segmentation method in determining the background image. In addition, the detection process uses the background subtraction method. Applying these two methods requires image preprocessing using several methods such as grayscaling, blurring (low-pass filter). In addition, it is followed by a thresholding and filtering process to get the best image in the detection process. In the process, there is a determination of the ROI to determine the focus area of the object identified as empty parking. The parking detection process produces the best average accuracy of 95.76%. The minimum threshold value of 255 pixels is 0.4. This value is the best value from 33 test data in several criteria, such as the time of capture, composition and color of the vehicle, the shape of the shadow of the object’s environment, and the intensity of light. This parking detection system can be implemented in real-time to determine the position of an empty place.
Quality of service performances of video and voice transmission in universal ...journalBEEI
The universal mobile telecommunications system (UMTS) has distinct benefits in that it supports a wide range of quality of service (QoS) criteria that users require in order to fulfill their requirements. The transmission of video and audio in real-time applications places a high demand on the cellular network, therefore QoS is a major problem in these applications. The ability to provide QoS in the UMTS backbone network necessitates an active QoS mechanism in order to maintain the necessary level of convenience on UMTS networks. For UMTS networks, investigation models for end-to-end QoS, total transmitted and received data, packet loss, and throughput providing techniques are run and assessed and the simulation results are examined. According to the results, appropriate QoS adaption allows for specific voice and video transmission. Finally, by analyzing existing QoS parameters, the QoS performance of 4G/UMTS networks may be improved.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Substrate integrate waveguide and microstrip antennas at 28 GHz
1. Bulletin of Electrical Engineering and Informatics
Vol. 9, No. 6, December 2020, pp. 2462~2468
ISSN: 2302-9285, DOI: 10.11591/eei.v9i6.2190 2462
Journal homepage: http://beei.org
Substrate integrate waveguide and microstrip antennas
at 28 GHz
Yaqdhan Mahmood Hussein1
, Mohamad Kamal A. Rahim2
, Noor Asniza Murad3
,
Mustafa Mohammed Jawad4
, Hatem O. Hanoosh5
, Huda A. Majid6
, Hussam H. A. Keriee7
1,2,3,4,5,7
Advanced RF & Microwave Research Group, School of Electrical Engineering
Faculty of Engineering, Universiti Teknologi Malaysia, Johor, Malaysia
6
Department of Electrical Engineering Technology, Faculty of Engineering Technology (FTK)
Universiti Tun Hussein Onn Malaysia, Johor, Malaysia
Article Info ABSTRACT
Article history:
Received Jan 13, 2019
Revised Mar 31, 2020
Accepted Apr 25, 2020
In this paper, two antennas are designed using substrate integrated waveguide
(SIW) and microstrip technology at 28 GHz. Parametric study for both
antennas is presented to demonstrate the performance at millimeter wave
frequency for wireless communication network (5G application). Roger RT5880
substrates with permittivity 2.2 and loss tangent 0.0009 are used to implement
the antennas with two thicknesses of 0.508 mm and 0.127 mm respectively.
Both antennas have the same size of substrate 12x12 mm with a full ground
plane was used. Structures designs have been done by using computer
simulation technology (CST). The simulation results showed that the antenna
with SIW and roger RT 5880 substrate thickness 0.508 has better
performance in term of return loss and radiation pattern than the microstrip
patch antenna at 28 GHz. A return loss more than -10 dB and the gain
are 6.4 dB obtained with wide bandwidth range of (27.4-28.7) GHz.
This proving to increase the realized gain by implementing SIW at millimeter
wave band for 5G application network.
Keywords:
Antenna
Microstrip
Millimeter wave
Substrate integrated waveguide
Wireless communication
This is an open access article under the CC BY-SA license.
Corresponding Author:
Yaqdhan Mahmood Hussein,
Advanced RF & Microwave Research Group, School of Electrical Engineering,
Faculty of Engineering, Universiti Teknologi Malaysia,
81310, Skudai, Johor Bahru, Johor, Malaysia.
Email: yaqthanm79@gmail.com
1. INTRODUCTION
Recently, the demands for high gain antenna with low profile for millimeter wave (mm-Wave)
are needed. The target is to increase the receiver sensitivity at the user point. However, the pathloss
and components loss are the major factors that should be taken in consideration in the mm-wave frequency [1].
Various techniques are based on the finite-difference time-domain technique or the finite-difference
frequency domain [2], the boundary integral-resonant mode expansion (BI-RME) technique [3], the method
of lines [4], and the transverse resonance method [5].
There are antenna configurations that have been done in the literature. A modified Vivaldi radiator
was introduced in [6]. It consists of a dual V-type linearly tapered slot antenna, with centre frequency at
36 GHz. Also, this antenna topology suited for integration in substrate integrated waveguide (SIW)
technology. Cavity-backed SIW antennas have been improved [7-9]. The single structure was offered in [7].
It contains a slotted SIW cavity supported by a coplanar waveguide, compact, single-substrate cavity-backed
slot and patch oscillator antennas were offered in [10], respectively, a non-detailed schematic of the design
2. Bulletin of Electr Eng & Inf ISSN: 2302-9285
Substrate integrate waveguide and microstrip antennas at 28 GHz (Yaqdhan Mahmood Hussein)
2463
circuit. Various techniques of active antennas, such as injection locking, cavity control, varactor tuned
antenna, and oscillation feedback loop, have been presented [11].
Microstrip patch antennas (MPAs) have been used in wireless and telecommunication systems but it
offers lower gain also It has lower power handling capability [12]. Recently, SIW has been used more than
common waveguide and microstrip because it is bulky and expensive [13]. The parameters of the SIW cavity
should be designed with care. The vias spacing (S) and diameter (D) affect considerably the return and
radiation losses, whereas, the waveguide width substrate integrated waveguide (WSIW) controls the cut-off
frequency and propagation constant [14]. The current flowing through the probe makes a magnetic field,
which matches with the magnetic field inside the SIW structure [15]. At millimeter-wave frequencies, high
gain antennas are required to overcome the signal attenuation due to oxygen molecules absorption [16].
To make the antenna radiate two-band need to request in order to use the currently available allocated 5G
spectrums in a wave system [17, 18]. The antenna consists of a 1-to-8-way SIW power divider and 8 Vivaldi
elements however this design wide bandwidth (38.9~45.1 GHz) with this high-frequency be a complex
design [19, 20]. Multiple-input-multiple-output (MIMO) and designed with the guidance of a genetic
algorithm (GA) antennas are broadly used for the improvement of antenna capacity and this technology has
been done for 4G as well as 5G communications. Wireless systems have taken an increased interest, as new
applying for millimeter waves (mm-waves) is being introduced and improved. In fact, a kind of application
has been recently offered in the frequency range over 60-94 GHz, including wireless networks [21],
automotive radars [22], imaging sensors [23], and biomedical devices [24].
This paper introduces four types of antennas. Two antennas implemented by using microstrip
technology with different thickness and the other antennas implemented using SIW technology with various
thicknesses. To prove the concept of SIW performance better than microstrip at mm-wave frequency in term
of gain and return loss, a simulation has been done by using computer simulation technology cst software to
compare the performance of the four antennas.
2. RESEARCH METHOD
The general structure of SIW is shown in Figure 1. It consists of a rectangular waveguide, two rows
of periodic holes, and a substrate at the top and bottom of ground planes, structure [25, 26]. The proposed
SIW antennas were designed using Rogers RT5880 substrate. The substrate has a dielectric constant of 2.2
and loss tangent of 0.0009. Two different substrate thicknesses were chosen, which are 0.508 mm and 0.127 mm.
Figure 1. The prospective general structure of a substrate integrated waveguide [29]
Microstrip patch antenna is implemented using same substrate Roger RT5880 with two different
thicknesses 0.508 mm and 0.127 mm. The vias diameter D and spacing S are calculated using equations
in [27, 28]. Full ground plane is used for all the antennas. Figure 2 shows the dimensions of the proposed
antennas at 28 GHz. As can be seen from Figure 2(a), the micro strip patch has the dimension of 4.6×8 mm
with substrate thickness 0.508mm and Figure 2(b), the dimension of structure 7.24×7.8 mm with thickness
0.127mm. Figure 2(c) refers to the SIW antenna with thickness substrate 0.127 and the dimension of
structure is 7.38×8.2 mm, Figure 2(d) to explain the SIW antenna with a thickness 0.508mm and
the dimension of structure is 7.68×8.2 mm. On the other hand, the proposed dimensions of substrate of
the SIW and microstrip antenna are 12×12 mm.
3. ISSN: 2302-9285
Bulletin of Electr Eng & Inf, Vol. 9, No. 6, December 2020 : 2462 – 2468
2464
(a) (b)
(c) (d)
Figure 2. Proposed SIW and microstrip antennas with two different thickness of the substrate
3. RESULTS AND DISCUSSION
All the antennas were simulated by using CST program, the characteristics of computer which used
to design are RAM 8GHz and processor intel CPU E3-1240 v2 @3.40 GHz (8CPU) with windows 10
operating system with this characteristic of computer the time simulation was around one hour for each
design. The return loss of the proposed antennas is shown in Figure 3. It can be clearly seen that the SIW
antenna with thickness of 0.508 mm has the best return loss of -34 dB at 28 GHz compared to others,
the SIW antenna was able to achieve a bandwidth 1.3 GHz from (27.3- 28.7) GHz while the best results of
the best patch antenna design was achieve 1.2 GHz (27.4-28.6) GHz with return loss 16 dB, On the aspect of
return loss, it can be seen evidently that the SIW performed better than the patch antenna.
Figure 3. the return loss of the microstrip and SIW antenna with different thickness
In this paper, there is relation between the thickness of substrate and the width of feedline.
Two structures have been designed with different widths of feedline. The feedline frequency and the
thickness of substrate have effect on 50-ohm impedance matching. The feedline have width of 0.3 mm with
substrate thickness 0.127 mm and the feedline have width 1.57 mm with substrate thickness 0.508 mm.
4. Bulletin of Electr Eng & Inf ISSN: 2302-9285
Substrate integrate waveguide and microstrip antennas at 28 GHz (Yaqdhan Mahmood Hussein)
2465
The 3D radiation pattern of the proposed antennas can be seen in Figure 4. SIW antennas using
Rogers RT5880 substrate with thickness 0.508 mm archived better gain, directivity, and return loss as
compared to the different thickness and Table 1 summaries the performance of the proposed antennas at
28 GHz. In term of gain and directivity, it can be shows by the 3D radiate onto pattern that the SIW
performed better than the patch antenna.
(a) (b)
(c) (d)
Figure 4. 3D radiation pattern, (a) SIW with thickness 0.508 mm, (b) SIW with thickness 0.127 mm,
(c) Microstrip with thickness 0.508 mm, (d) Microstrip with thickness 0.127 mm
Table 1. Performance comparison between microstrip and SIW antenna
Type of substrate Size of thickness Gain dB Directivity dBi S11
SIW antenna,
Rogers RT5880
0.508 6.4 7.67 -33.44
0.127 5.02 6.55 -16.9
Patch antenna,
Rogers RT5880
0.508 5.59 6.08 -16.7
0.127 5.07 6.57 -23.6
As shown in Figure 5 the radiation pattern 2D of the four structure, it explain the different radiation
of the structures and can see the radiation of the microstrip antenna with two the thicknesses 0.127 mm
and 0.508 in one direction, however it have back loop and side loop, and the SIW s design with thickness
0.127 mm has back and side loop also it not regular radiation, the radiation of SIW design with thickness
0.508 has wide radiation and regular.
It can be noticed from the above table, that the SIW antennas have better performnce in term of gain
and return loss than common patch microstrip antenna. When the thickness is decreased in SIW the gain
is reduced. Therfore, SIW anenna with substrate thickness of 0.508 is sutable at 28 GHz. Table 2 shows
camparation between some articals which have deign by SIW at the same frequncy with this work.
5. ISSN: 2302-9285
Bulletin of Electr Eng & Inf, Vol. 9, No. 6, December 2020 : 2462 – 2468
2466
Figure 5. The radiation pattern 2D of the four structure
Table 2. camparartion between some article with SIW technology
Ref Operating freq. (GHz) Substrate/dielectric constant Gain (dB) B.W (GHz) S-Parameter (dB)
[30] 28 Rogers 5880 7 5.7 -26
[31] 28 Rogers 4003 6.75 2 -28
[32] 28 FR4 4.7 5 -25
This work 28 Rogers 5800 6.4 1.3 -33
4. CONCLUSION
A substrate integrate waveguide and microstrip patch antenna are presented in this work by using
CST, substrates Rogers RT5880 used to design SIW and patch antennas the performance and the results
under this different substrate size, antenna gave different results. SIW with rogers RT5880 and thickness
0.508 gave better return loss -33.44 at 28 GHz with gain 6.4 dB and the directivity is 7.67, in addition,
the side loops of the antenna reduced. Rogers 5880 RT with 0.508 thickness is suitable for the millimeter wave.
ACKNOWLEDGEMENTS
The authors would like to thank the Ministry of Education (MOE), Research Management Centre
(RMC) School of Postgraduate Studies (SPS), Advanced RF and Microwave Research Group (ARFMRG),
School of Electrical Engineering, and Universiti Teknologi Malaysia (UTM), Johor Bahru, for the support of
the research under Grant 06G15 and 04G67. The authors also would like to acknowledge all members of
the Advanced RF and Microwave Research Group (ARFMRG)
REFERENCES
[1] M. Stanley, Y. Huang, T. Loh, Q. Xu, H. Wang, and H. Zhou, “A high gain steerable millimeter-wave antenna
array for 5G smartphone applications,” 2017 11th European Conference on Antennas and Propagation (EUCAP),
pp. 1311-1314, 2017.
[2] Fengxu, Yulin Zhang, Wei Hong, Ke Wu, and Tie Jun Cui, “Finite-difference frequency-domain algorithm for
modeling guided-wave properties of substrate integrated waveguide,” IEEE Transactions on Microwave Theory
and Techniques, vol. 51, no. 11, pp. 2221-2227, Nov. 2003.
[3] Y. Cassivi, L. Perregrini, P. Arcioni, M. Bressan, K. Wu, and G. Conciauro, “Dispersion characteristics of substrate
integrated rectangular waveguide,” IEEE Microwave and Wireless Components Letters, vol. 12, no. 9, pp. 333-335,
Sept. 2002.
[4] L. Yan, W. Hong, K. Wu, and T. J. Cui, “Investigations on the propagation characteristics of the substrate
integrated waveguide based on the method of lines,” IEE Proceedings - Microwaves, Antennas and Propagation,
vol. 152, no. 1, pp. 35-42, 19 Feb. 2005.
[5] D. Deslandes and Ke Wu, “Accurate modeling, wave mechanisms, and design considerations of a substrate
integrated waveguide,” IEEE Transactions on Microwave Theory and Techniques, vol. 54, no. 6, pp. 2516-2526,
June 2006.
[6] Y. J. Cheng, W. Hong, and K. Wu, “Design of a monopulse antenna using a dual v-type linearly tapered slot
antenna (DVLTSA),” IEEE Transactions on Antennas and Propagation, vol. 56, no. 9, pp. 2903-2909, Sept. 2008.
6. Bulletin of Electr Eng & Inf ISSN: 2302-9285
Substrate integrate waveguide and microstrip antennas at 28 GHz (Yaqdhan Mahmood Hussein)
2467
[7] G. Q. Luo, Z. F. Hu, L.x. Dong, and L. L. Sun, “Planar Slot Antenna Backed by Substrate Integrated Waveguide
Cavity,” IEEE Antennas and Wireless Propagation Letters, vol. 7, pp. 236-239, 2008.
[8] J. C. Bohorquez, H. A. Forero Pedraza, I. C. H. Pinzon, J. A. Castiblanco, N. Pena and H. F. Guarnizo, “Planar
substrate integrated waveguide cavity-backed antenna,” IEEE Antennas and Wireless Propagation Letters, vol. 8,
pp. 1139-1142, 2009.
[9] M. H. Awida and A. E. Fathy, “Substrate-integrated waveguide Ku-band cavity-backed 2 * 2 microstrip patch array
antenna,” IEEE Antennas and Wireless Propagation Letters, vol. 8, pp. 1054-1056, 2009.
[10] F. Giuppi, A. Georgiadis, M. Bozzi, S. Via, A. Collado, and L. Perregrini, “Hybrid nonlinear and electromagnetic
design of an active oscillator SIW cavity backed slot antenna,” Proceedings of Applied Computational
Electromagnetics Society (ACES 2010), pp. 23-29, 2010.
[11] P. Rajani Kumari, K. Chenna Kesava Reddy, and K.S. Ramesh, “Hybrid low complex near optimal detector for
spatial modulation,” International Journal of Electrical and Computer Engineering, vol 7, no 2, pp. 818-822, 2017.
[12] I. Ali, M. H. Jamaluddin, M. R. Kamarudin, A. Gaya, M. H. Dahri, “Gain enhancement of dielectric resonator
antenna for millimeter wave applications,” TELKOMNIKA Telecommunication, Computing, Electronics and
Control, vol. 17, no. 4, pp. 1670-1673, 2019.
[13] D. Deslandes and K. Wu, “Integrated microstrip and rectangular waveguide in planar form,” IEEE Microwave and
Wireless Components Letters, vol. 11, no. 2, pp. 68-70, Feb. 2001.
[14] M. Asaadi and A. Sebak, “High gain low profile slotted SIW cavity antenna for 5G applications,” 2016 IEEE
International Symposium on Antennas and Propagation (APSURSI), Fajardo, pp. 1227-1228, 2016.
[15] D. Deslandes and Ke Wu, “Analysis and design of current probe transition from grounded coplanar to substrate
integrated rectangular waveguides,” IEEE Transactions on Microwave Theory and Techniques, vol. 53, no. 8,
pp. 2487-2494, Aug. 2005.
[16] O. M. Haraz, A. Elboushi, S. A. Alshebeili, and A. Sebak, “Dense dielectric patch array antenna with improved
radiation characteristics using EBG ground structure and dielectric superstrate for future 5G cellular networks,”
IEEE Access, vol. 2, pp. 909-913, 2014.
[17] N. Ashraf, O. Haraz, M. A. Ashraf, and S. Alshebeili, “28/38-GHz dual-band millimeter wave SIW array antenna
with EBG structures for 5G applications,” 2015 International Conference on Information and Communication
Technology Research (ICTRC), pp. 5-8, 2015.
[18] P. Liu, X. Zhu, X. Wang, and L. Tian, “A SIW-Based vivaldi array antenna for 5G wireless communication
systems,” 2017 IEEE International Symposium on Antennas and Propagation & USNC/URSI National Radio
Science Meeting, pp. 529-530, 2017.
[19] A. Ghalib, M. S. Sharawi, H. Attia, and R. Mittra, “Broadband Substrate Integrated Waveguide Slotted Array
Antenna at mm-Wave Bands,” 2018 IEEE MTT-S International Microwave Workshop Series on 5G Hardware and
System Technologies (IMWS-5G), pp. 1-3, 2018.
[20] Mohammad S. Sharawi, “Printed MIMO Antenna Engineering Norwood,” Norwood: Artech House, USA, 2014.
[21] R. C. Daniels and R. W. Heath, “60 GHz wireless communications: Emerging requirements and design
recommendations,” IEEE Vehicular Technology Magazine, vol. 2, no. 3, pp. 41-50, Sept. 2007.
[22] W. J. Fleming, “New automotive sensors-A review,” IEEE Sensors Journal, vol. 8, no. 11, pp. 1900-1921,
Nov. 2008.
[23] L. Yujiri, M. Shoucri, and P. Moffa, “Passive millimeter wave imaging,” IEEE Microwave Magazine, vol. 4, no. 3,
pp. 39-50, Sept. 2003.
[24] K. Mizuno, Y. Wagatsuma, H. Warashina, K. Sawaya, H. Sato, S. Miyanaga, and Y. Yamanaka, “Millimeter-wave
imaging technologies and their applications,” 2007 IEEE International Vacuum Electronics Conference,
pp. 1-2, 2007.
[25] M. A. A. Rahim, I. M. Ibrahim, R. A. A. Kamaruddin, Z. Zakaria, and N. Hassim, “Characterization of microstrip
patch array antenna at 28 GHz," Journal of Telecommunication, Electronic and Computer Engineering (JTEC),
vol. 9, no. 2-8, pp. 137-141, 2017.
[26] M. Bozzi, A. Georgiadis, and K. Wu, “Review of substrate-integrated waveguide circuits and antennas,” IET
Microwaves, Antennas & Propagation, vol. 5, no. 8, pp. 909-920, June 2011.
[27] M. Ghorbani and H. Ghorbaninejad, “Novel high-gain narrowband waveguide-fed filtenna using genetic
algorithm,” International Journal of Electrical and Computer Engineering, vol. 7, no. 1, pp. 253-259, 2017.
[28] T. G. Siang, D. P. D. Dass, S. Z. Ibrahim, M. N. A. Karim, and A. A. Dewani, “Design of Ku-band power divider
using Substrate Integrated Waveguide technique,” Bulletin of Electrical Engineering and Informatics, vol. 8, no. 1,
pp. 172-179, 2019.
[29] N. Kathuria and S. Vashisht, “Dual-band printed slot antenna for the 5G wireless communication network,” 2016
International Conference on Wireless Communications, Signal Processing and Networking (WiSPNET),
pp. 1815-1817, 2016.
[30] Z. U. Khan, S. F. Jilani, A. Belenguer, T. H. Loh, and A. Alomainy, “Empty substrate integrated waveguide-fed
MMW aperture-coupled patch antenna for 5G applications,”12th European Conference on Antennas and
Propagation (EuCAP 2018), pp. 1-3, 2018.
[31] K. Y. Kapusuz, S. Lemey, and H. Rogier, “Dual-polarized 28-GHz air-filled SIW phased antenna array for next-
generation cellular systems,” 2019 IEEE International Symposium on Phased Array System & Technology (PAST),
pp. 1-6, 2019.
[32] W. M. Abdel-Wahab, Y. Wang, H. Al-Saedi, H. A. Mohamed, and S. Safavi-Naeini, “A broadband RHCP/LHCP
SIW-integrated patch array antenna for MM-wave applications,” 2018 IEEE International Symposium on Antennas
and Propagation & USNC/URSI National Radio Science Meeting, pp. 1741-1742, 2018.
7. ISSN: 2302-9285
Bulletin of Electr Eng & Inf, Vol. 9, No. 6, December 2020 : 2462 – 2468
2468
BIOGRAPHIES OF AUTHORS
Yaqdhan Mahmood Hussein was born in sammawah, Iraq, in 1991. He received the B.S in
computer techniques engineering in 2014-2015 from Islamic University College in Najaf city.
and M.S. degrees in electronic engineering (telecommunication system) from Universiti
Teknikal Malaysia Melaka (UTeM), Malaysia, in 2018, respectively, and he studies the Ph.D.
degree in electronic engineering in Universiti Teknologi Malaysia (UTM) in Johor Bahru city,
His current research interests include millimeter wave antennas, base station antennas, and SIW
technology with butler matrix.
Mohamad Kamal is the professor at Communication Engineering Department Faculty
of Electrical Engineering, Universiti Teknologi Malaysia (UTM). He is Deputy Dean Research
and Innovation and Head of Advanced RF & Microwave Research Group. His research interest
includes the areas of design of Dielectric resonator antennas, microstrip antennas, small
antennas, microwave sensors, RFID antennas for readers and tags, Multi-function antennas,
microwave cicuits, EBG, artificial magnetic conductors, metamaterials, phased array antennas.
Noor A Murad currently works at the School of Electrical Engineering, Faculty of Engineering,
Universiti Teknologi Malaysia (UTM), Johor, Malaysia. Noor does research in antenna design as
well as other microwave and millimeter wave devices. Her current research is on waveguide-
based devices at millimeter wave.
Mustafa Mohammed Jawad Abed was born in Baghdad, Iraq, He received the B.S in computer
techniques engineering in 2010 from Al Rafidain University College in Baghdad city. and M.S.
degrees in electronic engineering (telecommunication system) from Universiti Teknikal
Malaysia Melaka (UTeM), Malaysia, in 2018, respectively, and he studies the Ph.D. degree in
electronic engineering in Universiti Teknologi Malaysia (UTM) in Johor Bahru city. His current
research interests include wireless body area network, frequency-selective surface and substrate
integrated waveguide antenna.
Hatem Oday Hanoosh was born in samawah, Iraq, in 1991. He received the B.S in computer
techniques engineering in 2014-2015 from Islamic University College in Najaf city. and M.S.
degrees in electronic engineering (telecommunication system) from Universiti Teknikal
Malaysia Melaka (UTeM), Malaysia, in 2018, respectively, and he studies the Ph.D. degree in
electronic engineering in Universiti Teknologi Malaysia (UTM) in Johor Bahru city. His current
research interests include millimeter-wave antennas, base station antennas, and waveguide slot
antennas.
Huda A. Majid received the B Eng. degree in electrical engineering (telecommunication) from
Universiti Teknologi Malaysia (UTM) in 2007 and the M.Eng. degree and the Ph.D. degree in
electrical engineering from Universiti Teknologi Malaysia in 2010 and 2013, respectively. He is
currently a Lecturer with the Department of Electrical Engineering Technology, Faculty of
Engineering Technology, Universiti Tun Hussein Onn Malaysia (UTHM). He has published over
50 articles in journals and conference papers. His research interests include the areas of design of
microstrip antennas, small antennas, reconfigurable antennas, metamaterials structure,
metamaterial antennas, and millimeter wave antennas.
Hussam Hamid Abed Keriee was born in Baghdad, Iraq, in 1985. He received the B.S in
computer techniques engineering in 0202 from Al Rafidain University College in Baghdad city.
and M.S. degrees in electronic engineering (telecommunication system) from Universiti
Teknikal Malaysia Melaka, Malaysia in 2018. He studies the Ph.D. degree in electric
engineering in Universiti Teknologi Malaysia in Johor Bahru state. He is an active student
member of IEEE, and a member of IEEE Communications Society. His current research interests
include antenna design for mobile applications, metamaterial antenna, split-ring resonator,
frequency-selective surface.