Seamless steel pipe
•
0 likes•43 views
Seamless steel pipe (SMLS) is formed by drawing a solid billet over a piercing rod to create the hollow shell, without welding or seam. It is suitable for bending and flanging. The most advantage is increasing the ability of withstanding higher pressure. So it is widely used for boiler and pressure vessel, automotive area, oil well, and equipment components. Seamless steel pipe can be cut, threaded or grooved. And the coating method includes black / red lacquer, varnish painting, hot dip galvanization, etc.
Report
Share
Report
Share
Download to read offline
Recommended
Countergravity low pressure air (cla)
The document summarizes the controlled low-pressure casting (CLA) process in four steps: (1) a permeable mold is placed in a vacuum chamber with a sprue pipe extending into a crucible of molten metal, (2) applying a vacuum draws the molten metal into the mold cavity in a controlled flow, (3) the molten metal solidifies in the mold while remaining molten in the sprue, and (4) releasing the vacuum returns the leftover molten metal in the sprue back to the crucible. CLA casting yields higher quality parts with less waste metal compared to gravity pouring, and allows thinner sections, grain size control, and cleaner castings with fewer impurities.
Continuous casting
Continuous casting is a process used to cast metal into a continuous length. Molten metal is poured into a mold and solidifies into a casting as it travels downward. New molten metal is continuously supplied to the mold to keep the process going and produce a casting of indefinite length. The process requires precise control of parameters like molten metal flow to ensure smooth, continuous casting.
How to prevent weld failure
This document discusses various causes of weld failure and how to prevent them. It identifies several types of weld failures including overload, hot cracking, hydrogen induced cracking, and metallurgical failures. It also discusses defects such as cracks, lack of fusion, and porosity. To minimize failures, the document recommends carefully designing welds based on loading conditions, ensuring accessibility for welding, controlling distortion, considering the welding environment, matching processes to materials, and including safety factors in weld design stresses.
Tap hole mass & castable for iron runner
ShengIron Refractories contribute on tap hole gun mud and castable for iron runner production & application.
Taphole clay for blast furnace operation
This document discusses taphole clay and blast furnace operation from Sheng Iron Refractories. It covers three parts: (1) the importance of proper tapping times to safely remove molten iron and slag, (2) operation notices to maintain a safe taphole, including fully draining before plugging and avoiding humidity, and (3) factors to consider when choosing a quality taphole clay product, such as long stable taphole length and minimization of spraying during operation.
Fsw report
The document discusses friction stir welding (FSW), which uses a rotating tool to plastically join two metal surfaces without melting them. Students conducted an experiment using FSW to join aluminum and copper samples. They measured the hardness of the original and welded metals. The welded portions were found to be harder than the parent materials. FSW produces high-quality welds for applications like shipbuilding and aerospace with advantages of low distortion, excellent mechanical properties, and no porosity compared to fusion welding.
Thomson bsa veethread_specsheet
This document provides information on precision lead screws and supernuts from Ball Screws and Actuators (BS&A). It lists features such as low cost, customization options, variety of sizes, corrosion resistance, and vibration reduction compared to ball screws. It also provides details on material properties, temperature and load limits, accuracy grades, and self-locking characteristics. The document is intended to help customers understand and select the appropriate lead screw solutions for their linear motion needs.
Ptfe flex imperial smoothbore brochure
The document discusses an imperial range of hoses made of PTFE that are suitable for transferring electrically resistive fluids at high flow rates. Antistatic liners and stainless steel braided options are available. The hoses can operate in temperatures ranging from -60°C to +260°C and are used globally in industries such as industrial, chemical, pharmaceutical, automotive, and food. Technical specifications and part numbers are provided for standard wall hoses in sizes from 1/4" to 1".
Recommended
Countergravity low pressure air (cla)
The document summarizes the controlled low-pressure casting (CLA) process in four steps: (1) a permeable mold is placed in a vacuum chamber with a sprue pipe extending into a crucible of molten metal, (2) applying a vacuum draws the molten metal into the mold cavity in a controlled flow, (3) the molten metal solidifies in the mold while remaining molten in the sprue, and (4) releasing the vacuum returns the leftover molten metal in the sprue back to the crucible. CLA casting yields higher quality parts with less waste metal compared to gravity pouring, and allows thinner sections, grain size control, and cleaner castings with fewer impurities.
Continuous casting
Continuous casting is a process used to cast metal into a continuous length. Molten metal is poured into a mold and solidifies into a casting as it travels downward. New molten metal is continuously supplied to the mold to keep the process going and produce a casting of indefinite length. The process requires precise control of parameters like molten metal flow to ensure smooth, continuous casting.
How to prevent weld failure
This document discusses various causes of weld failure and how to prevent them. It identifies several types of weld failures including overload, hot cracking, hydrogen induced cracking, and metallurgical failures. It also discusses defects such as cracks, lack of fusion, and porosity. To minimize failures, the document recommends carefully designing welds based on loading conditions, ensuring accessibility for welding, controlling distortion, considering the welding environment, matching processes to materials, and including safety factors in weld design stresses.
Tap hole mass & castable for iron runner
ShengIron Refractories contribute on tap hole gun mud and castable for iron runner production & application.
Taphole clay for blast furnace operation
This document discusses taphole clay and blast furnace operation from Sheng Iron Refractories. It covers three parts: (1) the importance of proper tapping times to safely remove molten iron and slag, (2) operation notices to maintain a safe taphole, including fully draining before plugging and avoiding humidity, and (3) factors to consider when choosing a quality taphole clay product, such as long stable taphole length and minimization of spraying during operation.
Fsw report
The document discusses friction stir welding (FSW), which uses a rotating tool to plastically join two metal surfaces without melting them. Students conducted an experiment using FSW to join aluminum and copper samples. They measured the hardness of the original and welded metals. The welded portions were found to be harder than the parent materials. FSW produces high-quality welds for applications like shipbuilding and aerospace with advantages of low distortion, excellent mechanical properties, and no porosity compared to fusion welding.
Thomson bsa veethread_specsheet
This document provides information on precision lead screws and supernuts from Ball Screws and Actuators (BS&A). It lists features such as low cost, customization options, variety of sizes, corrosion resistance, and vibration reduction compared to ball screws. It also provides details on material properties, temperature and load limits, accuracy grades, and self-locking characteristics. The document is intended to help customers understand and select the appropriate lead screw solutions for their linear motion needs.
Ptfe flex imperial smoothbore brochure
The document discusses an imperial range of hoses made of PTFE that are suitable for transferring electrically resistive fluids at high flow rates. Antistatic liners and stainless steel braided options are available. The hoses can operate in temperatures ranging from -60°C to +260°C and are used globally in industries such as industrial, chemical, pharmaceutical, automotive, and food. Technical specifications and part numbers are provided for standard wall hoses in sizes from 1/4" to 1".
Fire Proofing On Steel Structure
1. Helical pins were welded onto a steel column and tested with 90 degree rotations to check weld strength.
2. The steel column was primed and sprayed with a Fendolite MII mixture to a thickness of 34mm.
3. Two coats of Cafco Topcoat 200 were applied to finish the fireproofing, with sealant applied at junctions.
Sandwich PUF Panel Manufacturer
Established in 1992 Group ALFA has emerged as one stop solution provider for all roofing components requirements. The Company has been at the forefront of the industry by offering the most extensive range of Metal roofing Products, Pre Engineered Steel Buildings, Steel Decking Sheet, Turbo Ventilators, Sandwich Puff Panel, Z&C Purlin and Reflective Insulation sheets.
Slips
Get W series Slips including WK slip, WT casing slip, WZ drilling pipe slip, and WZT drilling collar slip, Suitable for onshore or offshore drilling operations.
How to calculate gate area require for hpdc die casting part
For Getting gate area we need to know:
1.Casting Volume after gate including Overflow
2.Average wall thickness
3.Cavity fill time
4.Allowed gate velocity
5. Flow Rate
Must watch this video you understand everything about getting the gate area in detail with Calculations.
Please also watch my old video in Die Casting Die Design Playlist.
https://youtu.be/WhnFeAvz6eU
When you like my videos please do not forget to subscribe
for Subscribe you simply need to click the link below;
https://www.youtube.com/channel/UCLsS...
TDBL self tapping fastener
New product TDBL is designed to replace traditional hexagonal bolts, washers and nuts for fastening steel rails. TDBL can be installed using battery or pneumatic screwguns with one hand in a fraction of the time taken by manual installation with two hands and tools. It has been tested on site in France and features thread forming ability in various steel thicknesses from a single pilot hole size, no risk of over-driving or backing out, and equivalent strength to traditional bolts, washers and nuts. TDBL provides a quick and easy solution for rail and other industrial applications.
780073
This document describes improvements to valve guides for internal combustion engines made through powder metallurgy processes. Specifically, it describes coating the surfaces of the powder metallurgy-produced valve guides with corrosion-resistant metallic coatings to protect them from oxidation caused by exposure to hot exhaust gases. The coating can be applied through electrodeposition, spraying, or impregnation by dipping the guide in molten metal. This protects the guide from disintegrating due to internal oxidation.
780073
This document describes improvements to valve guides for internal combustion engines made through powder metallurgy processes. Specifically, it describes coating the surfaces of the powder metallurgy-produced valve guides with corrosion-resistant metallic coatings to protect them from oxidation caused by exposure to hot exhaust gases. The coating can be applied through electrodeposition, spraying, or impregnation by dipping the guide in molten metal. This protects the guide from disintegrating due to internal oxidation.
Topic 7 joining process welding brazing soldering fastening 160214
This document discusses various joining processes including welding, brazing, soldering, adhesive bonding, and mechanical fastening. It focuses on welding processes, describing fusion welding techniques like arc welding, resistance welding, oxyfuel welding, and others. For arc welding, it explains the basic configuration and different electrode and power source types. For resistance welding, it describes resistance spot welding and seam welding. The document also discusses solid state welding techniques that join materials without melting.
780073
This document describes improvements to valve guides for internal combustion engines made through powder metallurgy processes. Specifically, it describes coating the surfaces of the powder metallurgy-produced valve guides with corrosion-resistant metallic coatings to protect them from oxidation caused by exposure to hot exhaust gases. The coating can be applied through electrodeposition, spraying, or impregnation by dipping the guide in molten metal. This protects the guide from disintegrating due to internal oxidation.
Mechanical seal
The document discusses mechanical seals and their components. It describes single and double mechanical seals, as well as unbalanced and balanced mechanical seals. It also discusses tandem seals, barrier fluids, and calculating hydraulic balance percentage. Mechanical seals are used to prevent shaft wear by providing a replaceable surface that wears instead of the shaft. Barrier fluids are used to lubricate and cool mechanical seals, with different fluids used depending on the operating temperature range.
Bolt materials
Materials for automobiles must meet requirements for structural strength, cost, corrosion resistance, safety, and more. They are classified as metals, non-metals, and consumables. Metals include ferrous metals like steels and non-ferrous metals like aluminum and copper. Non-metals include rubbers, plastics, lubricants, and adhesives. Proper specification of materials properties is important whether they require processing or are procured finished. Bolted joints are discussed as an example, outlining specifications needed for bolts, nuts, washers, and the relationship between bolt grade and nut grade. Tightening methods like torque wrenches, pneumatic wrenches, and turn-of-
Forging
The document discusses various metal forming processes including forging processes like open die, closed die, and impression forging. It describes types of rolling processes and defects in rolled parts. It also covers principles of extrusion, types of extrusion, and tube drawing. Different metal forming techniques like forging, rolling, and extrusion are discussed along with their advantages in shaping metals and improving mechanical properties. Key terms related to forging like dies, forgings, and defects in forged parts are also summarized.
5016 5020.output
The document describes a method and apparatus for mechanically separating a part from a rod or tube-like workpiece made of a heat-softenable material. The separation involves heating the workpiece at a predetermined separation point and, when sufficiently softened, suddenly breaking off the piece using a previously held force, rather than gradually drawing it out. This avoids thinning the walls and produces a well-rounded fused top with uniform wall thickness, important for reliably sealing ampoules. The method can use preparatory stretching or compression of the workpiece to facilitate separation, especially of pieces with varying diameters or thicknesses, and ensure breaking occurs at the right softening point.
5 common types of bearing damage
The document discusses 5 common types of bearing damage: 1) Abrasive wear from contamination like sand or fine metal particles, 2) Pitting and bruising from hard particles, 3) Grooving from heavy wear from chips or metal particles, 4) Corrosion from lack of protection from moisture, and 5) Inadequate lubrication, which can cause issues ranging from discoloration to total bearing lockup.
Aanuraj Fasteners Pvt Ltd
Who are we…
An ISO 9001:2015 certified company,Aanuraj Fasteners Pvt. Ltd is one of the prominent manufacturers, exporters, and suppliers of an impressive series of industrial fasteners applied in diverse industrial sectors.
We are one of the top 10 manufacturer of Special Grade Threaded Fasteners for Infrastructure, Oil Gas production, Chemical Plant industries.
Our Range Include..
# ASTM A453 GR.660 CLASS A B C D Studs & Heavy Hex Nuts with Stress Rupture Report above 100 hours.
# ASTM A193 Gr.347 UNS S34700 Studs & Nuts
# UNS S31254 – SMO 254 Bolts Nuts Studs Washers
# Hastelloy Grade. C22 Studs Bolts Nuts Washer
# Hastelloy C276 Hex bolts Nuts Studs Washers
# Super Duplex UNS 32750 Hex Bolts Nuts Washers
# Duplex Steel Grdae 2205 31803 Hex bolts Nuts & Washers
# AISI 304 Stud Bolts Nut Washers
# AISI 316 Hex Bolts Nuts & Washers
# AISI 310 Hex Bolts Studs Nuts Washers
# AISI 317L Grade Bolts Nuts Washers
# AISI 904L – UNS N08904 Bolts Nuts Studs Washers
# Alloy 20 Grade Bolts studs Nuts Washers
# Monel K400 Grade Hex Bolts Nuts Washers
# ASTM A 193 Grade.. B7 Studs Bolts
# Foundation Bolts. L Bolts, U Bolts, J Bolts
# Nut Bolt Assembly Machine
walkson-presentation-r1.pdf
WALKSON are International Strategic Sourcing Company for casting,forging,fabrication components. We are committed to the manufacture of castings, forgings, fabrications to your design and specification with Max. weight for casting up to 150tons/pc, for forging up to 200ton/pc,for fabrication according customer requirement. Acting as your reliable partner, our goal is to deliver every competetive product to meet your satisfaction! With more than 10 years international strategic sourcing experience, we will ensure to give metal fields risk free access to our International supply chain
CuNi hsc
Manufacturer of Copper Nickel Pipe, Fittings, Flanges, Sheet, Plate, Rod, Fastener, Valves, etc in UNS C70600 & C71500 Grade based in India
For Inquiries, mail to
jatinsanghvi9@gmail.com
Astm a335-p5-alloy-seamless-pipe
ASTM A335, ASTM A335 P5, ASTM A335 P5 alloy pipe, seamless steel pipes, steel pipes
Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices.
COMPANY PROFILE (PSI)
Piping Solutions International (PSI) provides piping solutions to various industries such as oil and gas, power generation, and ship building. They supply pipes, plates, fittings, flanges, and valves made of materials like carbon steel, stainless steel, and alloys. PSI aims to be a world-class supplier and critical component provider known for its experienced professionals and ability to adapt to changing market needs.
Quality Oriented and ISO Approved Stainless Steel 446 Buttweld Pipe Fittings ...
India’s one of the Leaders Amongst Manufacturers, Stockist, Exporters, and Global Suppliers of ASME/ANSI B16.9 / ANSI B16.28 / MSS SP-43/SP-79 / ASME SA403M Stainless Steel 446 Elbow, Tee, Reducers, Cross, Stub End, Nipple, Bend, End Cap, Collar, 446 Welded and Seamless Pipe Fittings
Erw Steel Pipe Tom Lv
ERW Steel Pipe Made in China and From the original supplier : Heibei Changfeng Steel Tube Manufacturing Group Co.,Ltd.
Tom Lv
tomlv@changfengsteeltube.com
www.changfengsteeltube.com
Astech Alloy Steel Technology
Astech specializes in casting small to medium sized alloy steel and iron components. They produce a variety of abrasion resistant, heat resistant, corrosion resistant, and tool steels within tight composition specifications. Astech has the capability to manufacture prototypes as well as short and long production runs tailored to customer needs. In addition to casting services, Astech also provides engineering support including modeling, design, and machining.
More Related Content
What's hot
Fire Proofing On Steel Structure
1. Helical pins were welded onto a steel column and tested with 90 degree rotations to check weld strength.
2. The steel column was primed and sprayed with a Fendolite MII mixture to a thickness of 34mm.
3. Two coats of Cafco Topcoat 200 were applied to finish the fireproofing, with sealant applied at junctions.
Sandwich PUF Panel Manufacturer
Established in 1992 Group ALFA has emerged as one stop solution provider for all roofing components requirements. The Company has been at the forefront of the industry by offering the most extensive range of Metal roofing Products, Pre Engineered Steel Buildings, Steel Decking Sheet, Turbo Ventilators, Sandwich Puff Panel, Z&C Purlin and Reflective Insulation sheets.
Slips
Get W series Slips including WK slip, WT casing slip, WZ drilling pipe slip, and WZT drilling collar slip, Suitable for onshore or offshore drilling operations.
How to calculate gate area require for hpdc die casting part
For Getting gate area we need to know:
1.Casting Volume after gate including Overflow
2.Average wall thickness
3.Cavity fill time
4.Allowed gate velocity
5. Flow Rate
Must watch this video you understand everything about getting the gate area in detail with Calculations.
Please also watch my old video in Die Casting Die Design Playlist.
https://youtu.be/WhnFeAvz6eU
When you like my videos please do not forget to subscribe
for Subscribe you simply need to click the link below;
https://www.youtube.com/channel/UCLsS...
TDBL self tapping fastener
New product TDBL is designed to replace traditional hexagonal bolts, washers and nuts for fastening steel rails. TDBL can be installed using battery or pneumatic screwguns with one hand in a fraction of the time taken by manual installation with two hands and tools. It has been tested on site in France and features thread forming ability in various steel thicknesses from a single pilot hole size, no risk of over-driving or backing out, and equivalent strength to traditional bolts, washers and nuts. TDBL provides a quick and easy solution for rail and other industrial applications.
780073
This document describes improvements to valve guides for internal combustion engines made through powder metallurgy processes. Specifically, it describes coating the surfaces of the powder metallurgy-produced valve guides with corrosion-resistant metallic coatings to protect them from oxidation caused by exposure to hot exhaust gases. The coating can be applied through electrodeposition, spraying, or impregnation by dipping the guide in molten metal. This protects the guide from disintegrating due to internal oxidation.
780073
This document describes improvements to valve guides for internal combustion engines made through powder metallurgy processes. Specifically, it describes coating the surfaces of the powder metallurgy-produced valve guides with corrosion-resistant metallic coatings to protect them from oxidation caused by exposure to hot exhaust gases. The coating can be applied through electrodeposition, spraying, or impregnation by dipping the guide in molten metal. This protects the guide from disintegrating due to internal oxidation.
Topic 7 joining process welding brazing soldering fastening 160214
This document discusses various joining processes including welding, brazing, soldering, adhesive bonding, and mechanical fastening. It focuses on welding processes, describing fusion welding techniques like arc welding, resistance welding, oxyfuel welding, and others. For arc welding, it explains the basic configuration and different electrode and power source types. For resistance welding, it describes resistance spot welding and seam welding. The document also discusses solid state welding techniques that join materials without melting.
780073
This document describes improvements to valve guides for internal combustion engines made through powder metallurgy processes. Specifically, it describes coating the surfaces of the powder metallurgy-produced valve guides with corrosion-resistant metallic coatings to protect them from oxidation caused by exposure to hot exhaust gases. The coating can be applied through electrodeposition, spraying, or impregnation by dipping the guide in molten metal. This protects the guide from disintegrating due to internal oxidation.
Mechanical seal
The document discusses mechanical seals and their components. It describes single and double mechanical seals, as well as unbalanced and balanced mechanical seals. It also discusses tandem seals, barrier fluids, and calculating hydraulic balance percentage. Mechanical seals are used to prevent shaft wear by providing a replaceable surface that wears instead of the shaft. Barrier fluids are used to lubricate and cool mechanical seals, with different fluids used depending on the operating temperature range.
Bolt materials
Materials for automobiles must meet requirements for structural strength, cost, corrosion resistance, safety, and more. They are classified as metals, non-metals, and consumables. Metals include ferrous metals like steels and non-ferrous metals like aluminum and copper. Non-metals include rubbers, plastics, lubricants, and adhesives. Proper specification of materials properties is important whether they require processing or are procured finished. Bolted joints are discussed as an example, outlining specifications needed for bolts, nuts, washers, and the relationship between bolt grade and nut grade. Tightening methods like torque wrenches, pneumatic wrenches, and turn-of-
Forging
The document discusses various metal forming processes including forging processes like open die, closed die, and impression forging. It describes types of rolling processes and defects in rolled parts. It also covers principles of extrusion, types of extrusion, and tube drawing. Different metal forming techniques like forging, rolling, and extrusion are discussed along with their advantages in shaping metals and improving mechanical properties. Key terms related to forging like dies, forgings, and defects in forged parts are also summarized.
5016 5020.output
The document describes a method and apparatus for mechanically separating a part from a rod or tube-like workpiece made of a heat-softenable material. The separation involves heating the workpiece at a predetermined separation point and, when sufficiently softened, suddenly breaking off the piece using a previously held force, rather than gradually drawing it out. This avoids thinning the walls and produces a well-rounded fused top with uniform wall thickness, important for reliably sealing ampoules. The method can use preparatory stretching or compression of the workpiece to facilitate separation, especially of pieces with varying diameters or thicknesses, and ensure breaking occurs at the right softening point.
5 common types of bearing damage
The document discusses 5 common types of bearing damage: 1) Abrasive wear from contamination like sand or fine metal particles, 2) Pitting and bruising from hard particles, 3) Grooving from heavy wear from chips or metal particles, 4) Corrosion from lack of protection from moisture, and 5) Inadequate lubrication, which can cause issues ranging from discoloration to total bearing lockup.
What's hot (14)
How to calculate gate area require for hpdc die casting part
How to calculate gate area require for hpdc die casting part
Topic 7 joining process welding brazing soldering fastening 160214
Topic 7 joining process welding brazing soldering fastening 160214
Similar to Seamless steel pipe
Aanuraj Fasteners Pvt Ltd
Who are we…
An ISO 9001:2015 certified company,Aanuraj Fasteners Pvt. Ltd is one of the prominent manufacturers, exporters, and suppliers of an impressive series of industrial fasteners applied in diverse industrial sectors.
We are one of the top 10 manufacturer of Special Grade Threaded Fasteners for Infrastructure, Oil Gas production, Chemical Plant industries.
Our Range Include..
# ASTM A453 GR.660 CLASS A B C D Studs & Heavy Hex Nuts with Stress Rupture Report above 100 hours.
# ASTM A193 Gr.347 UNS S34700 Studs & Nuts
# UNS S31254 – SMO 254 Bolts Nuts Studs Washers
# Hastelloy Grade. C22 Studs Bolts Nuts Washer
# Hastelloy C276 Hex bolts Nuts Studs Washers
# Super Duplex UNS 32750 Hex Bolts Nuts Washers
# Duplex Steel Grdae 2205 31803 Hex bolts Nuts & Washers
# AISI 304 Stud Bolts Nut Washers
# AISI 316 Hex Bolts Nuts & Washers
# AISI 310 Hex Bolts Studs Nuts Washers
# AISI 317L Grade Bolts Nuts Washers
# AISI 904L – UNS N08904 Bolts Nuts Studs Washers
# Alloy 20 Grade Bolts studs Nuts Washers
# Monel K400 Grade Hex Bolts Nuts Washers
# ASTM A 193 Grade.. B7 Studs Bolts
# Foundation Bolts. L Bolts, U Bolts, J Bolts
# Nut Bolt Assembly Machine
walkson-presentation-r1.pdf
WALKSON are International Strategic Sourcing Company for casting,forging,fabrication components. We are committed to the manufacture of castings, forgings, fabrications to your design and specification with Max. weight for casting up to 150tons/pc, for forging up to 200ton/pc,for fabrication according customer requirement. Acting as your reliable partner, our goal is to deliver every competetive product to meet your satisfaction! With more than 10 years international strategic sourcing experience, we will ensure to give metal fields risk free access to our International supply chain
CuNi hsc
Manufacturer of Copper Nickel Pipe, Fittings, Flanges, Sheet, Plate, Rod, Fastener, Valves, etc in UNS C70600 & C71500 Grade based in India
For Inquiries, mail to
jatinsanghvi9@gmail.com
Astm a335-p5-alloy-seamless-pipe
ASTM A335, ASTM A335 P5, ASTM A335 P5 alloy pipe, seamless steel pipes, steel pipes
Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices.
COMPANY PROFILE (PSI)
Piping Solutions International (PSI) provides piping solutions to various industries such as oil and gas, power generation, and ship building. They supply pipes, plates, fittings, flanges, and valves made of materials like carbon steel, stainless steel, and alloys. PSI aims to be a world-class supplier and critical component provider known for its experienced professionals and ability to adapt to changing market needs.
Quality Oriented and ISO Approved Stainless Steel 446 Buttweld Pipe Fittings ...
India’s one of the Leaders Amongst Manufacturers, Stockist, Exporters, and Global Suppliers of ASME/ANSI B16.9 / ANSI B16.28 / MSS SP-43/SP-79 / ASME SA403M Stainless Steel 446 Elbow, Tee, Reducers, Cross, Stub End, Nipple, Bend, End Cap, Collar, 446 Welded and Seamless Pipe Fittings
Erw Steel Pipe Tom Lv
ERW Steel Pipe Made in China and From the original supplier : Heibei Changfeng Steel Tube Manufacturing Group Co.,Ltd.
Tom Lv
tomlv@changfengsteeltube.com
www.changfengsteeltube.com
Astech Alloy Steel Technology
Astech specializes in casting small to medium sized alloy steel and iron components. They produce a variety of abrasion resistant, heat resistant, corrosion resistant, and tool steels within tight composition specifications. Astech has the capability to manufacture prototypes as well as short and long production runs tailored to customer needs. In addition to casting services, Astech also provides engineering support including modeling, design, and machining.
As df
Dynamic Forge & Pipe Fitting is an Indian manufacturer and supplier of piping products established in 2011. They produce a wide range of carbon steel, stainless steel, and alloy steel flanges, fittings, pipes, tubes, sheets, and fasteners. Their production facilities allow them to offer prompt delivery of stock and custom orders to meet various international standards and dimensions. They provide fabrication and other services and encourage customers to share their requirements.
Astm a335-p9-alloy-steel-pipe
ASTM A335 P9 is the part of ASTM A335, The pipe shall be suitable for bending, flanging, and similar forming operations, and for fusion welding. The steel material shall conform to chemical composition, tensile property, and hardness requirements.
Each length of pipe shall be subjected to the hydrostatic test. Also, each pipe shall be examined by a non-destructive examination method in accordance to the required practices.
The different mechanical test requirements for pipes, namely, transverse or longitudinal tension test, flattening test, and hardness or bend test are presented.Both ends of each crate will indicate the order no., heat no., dimensions, weight and bundles or as requested.
Rajaram Tubes
This document is an introduction letter from Rajaram Tubes (India) identifying themselves as one of the largest importers, stockholders, and suppliers of stainless steel, carbon steel, alloy steel, copper, brass, and other metals. They maintain bulk stock of a wide range of materials, including pipes, tubes, plates, coils, fittings, and valves, which they can supply in a timely manner at competitive rates. They serve various industries and hope to be added to approved vendor lists.
Haresh Steel Centre
Stainless Steel, Carbon Steel, Alloy Steel, Duplex Steel, Nickel, Inconel, Monel, Hastelloy, Copper, Cupronickel, Copper Alloys, Titanium, Aluminium, Other Non-Ferrous Metals in forms of Pipe, Tube, Pipe Fitting, Forged Fitting, Flange, Sheet, Plate, Rod, Wire, Structural, Valve, etc.
UNISTEELS COMPANY PROFILE PRODUCT RANGE
This document provides information about Unisteels & Engineering Company Pvt Ltd, an ISO 9001-2008 certified company established in 1970 that manufactures and distributes stainless steel, duplex steel, alloy steel, carbon steel, and exotic alloys. The company has manufacturing facilities and warehouses in Maharashtra, India and stocks over 1000 tons of steel sheets, plates, pipes, tubes, and fittings. It offers cutting, welding, perforation and other processing services and supplies products for applications in various industries.
Válvulas de bola - Ball Valves
Una válvula de bola, conocida también como válvula de esfera, es un mecanismo de llave de paso que sirve para regular el flujo de un fluido canalizado y se caracteriza porque el mecanismo regulador situado en el interior es una bola perforada.
A ball valve, also known as a spherical valve, is a stopcock mechanism used to regulate the flow of a piped fluid and is characterised by having a perforated ball inside as its regulating mechanism.
Hot rolled steel tube
Shanghai Unite Steel, a mechanical steel tubing manufacturer and stockiest from China.
Outer diameter: 51-530 mm
Wall thickness: 5-120 mm
Length: not more than 12 m
Product Catalog
TISCO SPP produces stainless steel tubes and pipes for various industries including petroleum, natural gas, petrochemicals, power plants, automobiles, and ships. The plant has an annual production capacity of 50,000 tons for seamless pipes and 10,000 tons for welded pipes in diameters ranging from 6-762 mm and wall thicknesses from 0.5-40 mm. Products are made from various stainless steel grades including austenitic, martensitic, ferritic, duplex, and nickel alloys. The plant has extensive production facilities including extrusion presses, rolling mills, heat treatment systems, non-destructive testing equipment, and a technology research center to ensure high quality products.
Multi mode Casting Process
Casting is a manufacturing process in which a liquid material is usually poured into a mold, which contains a hollow cavity of the desired shape, and then allowed to solidify. The solidified part is also known as a casting, which is ejected or broken out of the mold to complete the process.
BHUSHAN STEEL.pdf BROCHURE FOR STEEL TABLE
This document provides information about the manufacturing process for steel tubes at Bhushan Power and Steel Ltd. It begins with an overview of the company and its products. It then describes the tube manufacturing process which involves forming steel strips into tubular shapes and welding the edges. Various quality tests are conducted including hydraulic testing. Tubes may also be galvanized and threaded. Standards that the company's tubes conform to from various countries are listed. Details on specific tube types including dimensions, tolerances and material properties are provided.
Astm a409 a409-m-01(r05)
This document provides specifications for welded large diameter austenitic steel pipe for corrosive or high-temperature service. It specifies requirements for materials, manufacture, chemical composition, ordering information, and general requirements. The document references other industry standards and provides tables of chemical requirements for different pipe grades. Purchase orders for pipe to these specifications should include quantity, name of material, grade, size, length, end finish, and any optional requirements.
Alloy performance-guide
This document provides information on alloy performance including:
- Descriptions of common heat and corrosion resistant alloys including their chemical compositions and properties.
- Mechanical and physical properties for various alloys in the annealed condition.
- Maximum allowable design stress values for some alloys according to the ASME Boiler and Pressure Vessel Code.
- Charts with data on creep rates, stress to rupture, corrosion resistance, and other properties for different alloys at high temperatures.
Similar to Seamless steel pipe (20)
Quality Oriented and ISO Approved Stainless Steel 446 Buttweld Pipe Fittings ...
Quality Oriented and ISO Approved Stainless Steel 446 Buttweld Pipe Fittings ...
Recently uploaded
在线办理(salfor毕业证书)索尔福德大学毕业证毕业完成信一模一样
学校原件一模一样【微信：741003700 】《(salfor毕业证书)索尔福德大学毕业证》【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Describing and Interpreting an Immersive Learning Case with the Immersion Cub...
Current descriptions of immersive learning cases are often difficult or impossible to compare. This is due to a myriad of different options on what details to include, which aspects are relevant, and on the descriptive approaches employed. Also, these aspects often combine very specific details with more general guidelines or indicate intents and rationales without clarifying their implementation. In this paper we provide a method to describe immersive learning cases that is structured to enable comparisons, yet flexible enough to allow researchers and practitioners to decide which aspects to include. This method leverages a taxonomy that classifies educational aspects at three levels (uses, practices, and strategies) and then utilizes two frameworks, the Immersive Learning Brain and the Immersion Cube, to enable a structured description and interpretation of immersive learning cases. The method is then demonstrated on a published immersive learning case on training for wind turbine maintenance using virtual reality. Applying the method results in a structured artifact, the Immersive Learning Case Sheet, that tags the case with its proximal uses, practices, and strategies, and refines the free text case description to ensure that matching details are included. This contribution is thus a case description method in support of future comparative research of immersive learning cases. We then discuss how the resulting description and interpretation can be leveraged to change immersion learning cases, by enriching them (considering low-effort changes or additions) or innovating (exploring more challenging avenues of transformation). The method holds significant promise to support better-grounded research in immersive learning.
Equivariant neural networks and representation theory
Or: Beyond linear.
Abstract: Equivariant neural networks are neural networks that incorporate symmetries. The nonlinear activation functions in these networks result in interesting nonlinear equivariant maps between simple representations, and motivate the key player of this talk: piecewise linear representation theory.
Disclaimer: No one is perfect, so please mind that there might be mistakes and typos.
dtubbenhauer@gmail.com
Corrected slides: dtubbenhauer.com/talks.html
The binding of cosmological structures by massless topological defects
Assuming spherical symmetry and weak field, it is shown that if one solves the Poisson equation or the Einstein field
equations sourced by a topological defect, i.e. a singularity of a very specific form, the result is a localized gravitational
field capable of driving flat rotation (i.e. Keplerian circular orbits at a constant speed for all radii) of test masses on a thin
spherical shell without any underlying mass. Moreover, a large-scale structure which exploits this solution by assembling
concentrically a number of such topological defects can establish a flat stellar or galactic rotation curve, and can also deflect
light in the same manner as an equipotential (isothermal) sphere. Thus, the need for dark matter or modified gravity theory is
mitigated, at least in part.
ESA/ACT Science Coffee: Diego Blas - Gravitational wave detection with orbita...
ESA/ACT Science Coffee: Diego Blas - Gravitational wave detection with orbita...Advanced-Concepts-Team
Presentation in the Science Coffee of the Advanced Concepts Team of the European Space Agency on the 07.06.2024.
Speaker: Diego Blas (IFAE/ICREA)
Title: Gravitational wave detection with orbital motion of Moon and artificial
Abstract:
In this talk I will describe some recent ideas to find gravitational waves from supermassive black holes or of primordial origin by studying their secular effect on the orbital motion of the Moon or satellites that are laser ranged.Immersive Learning That Works: Research Grounding and Paths Forward
We will metaverse into the essence of immersive learning, into its three dimensions and conceptual models. This approach encompasses elements from teaching methodologies to social involvement, through organizational concerns and technologies. Challenging the perception of learning as knowledge transfer, we introduce a 'Uses, Practices & Strategies' model operationalized by the 'Immersive Learning Brain' and ‘Immersion Cube’ frameworks. This approach offers a comprehensive guide through the intricacies of immersive educational experiences and spotlighting research frontiers, along the immersion dimensions of system, narrative, and agency. Our discourse extends to stakeholders beyond the academic sphere, addressing the interests of technologists, instructional designers, and policymakers. We span various contexts, from formal education to organizational transformation to the new horizon of an AI-pervasive society. This keynote aims to unite the iLRN community in a collaborative journey towards a future where immersive learning research and practice coalesce, paving the way for innovative educational research and practice landscapes.
20240520 Planning a Circuit Simulator in JavaScript.pptx
Evaporation step counter work. I have done a physical experiment.
(Work in progress.)
Applied Science: Thermodynamics, Laws & Methodology.pdf
When I was asked to give a companion lecture in support of ‘The Philosophy of Science’ (https://shorturl.at/4pUXz) I decided not to walk through the detail of the many methodologies in order of use. Instead, I chose to employ a long standing, and ongoing, scientific development as an exemplar. And so, I chose the ever evolving story of Thermodynamics as a scientific investigation at its best.
Conducted over a period of >200 years, Thermodynamics R&D, and application, benefitted from the highest levels of professionalism, collaboration, and technical thoroughness. New layers of application, methodology, and practice were made possible by the progressive advance of technology. In turn, this has seen measurement and modelling accuracy continually improved at a micro and macro level.
Perhaps most importantly, Thermodynamics rapidly became a primary tool in the advance of applied science/engineering/technology, spanning micro-tech, to aerospace and cosmology. I can think of no better a story to illustrate the breadth of scientific methodologies and applications at their best.
The cost of acquiring information by natural selection
This is a short talk that I gave at the Banff International Research Station workshop on Modeling and Theory in Population Biology. The idea is to try to understand how the burden of natural selection relates to the amount of information that selection puts into the genome.
It's based on the first part of this research paper:
The cost of information acquisition by natural selection
Ryan Seamus McGee, Olivia Kosterlitz, Artem Kaznatcheev, Benjamin Kerr, Carl T. Bergstrom
bioRxiv 2022.07.02.498577; doi: https://doi.org/10.1101/2022.07.02.498577
Direct Seeded Rice - Climate Smart Agriculture
Direct Seeded Rice - Climate Smart AgricultureInternational Food Policy Research Institute- South Asia Office
PPT on Direct Seeded Rice presented at the three-day 'Training and Validation Workshop on Modules of Climate Smart Agriculture (CSA) Technologies in South Asia' workshop on April 22, 2024.
快速办理(UAM毕业证书)马德里自治大学毕业证学位证一模一样
学校原件一模一样【微信：741003700 】《(UAM毕业证书)马德里自治大学毕业证学位证》【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
SAR of Medicinal Chemistry 1st by dk.pdf
In this presentation include the prototype drug SAR on thus or with their examples .
Syllabus of Second Year B. Pharmacy
2019 PATTERN.
Shallowest Oil Discovery of Turkiye.pptx
The Petroleum System of the Çukurova Field - the Shallowest Oil Discovery of Türkiye, Adana
waterlessdyeingtechnolgyusing carbon dioxide chemicalspdf
The technology uses reclaimed CO₂ as the dyeing medium in a closed loop process. When pressurized, CO₂ becomes supercritical (SC-CO₂). In this state CO₂ has a very high solvent power, allowing the dye to dissolve easily.
Randomised Optimisation Algorithms in DAPHNE
Slides from talk:
Aleš Zamuda: Randomised Optimisation Algorithms in DAPHNE .
Austrian-Slovenian HPC Meeting 2024 – ASHPC24, Seeblickhotel Grundlsee in Austria, 10–13 June 2024
https://ashpc.eu/
THEMATIC APPERCEPTION TEST(TAT) cognitive abilities, creativity, and critic...
THEMATIC APPERCEPTION TEST(TAT) cognitive abilities, creativity, and critic...Abdul Wali Khan University Mardan,kP,Pakistan
hematic appreciation test is a psychological assessment tool used to measure an individual's appreciation and understanding of specific themes or topics. This test helps to evaluate an individual's ability to connect different ideas and concepts within a given theme, as well as their overall comprehension and interpretation skills. The results of the test can provide valuable insights into an individual's cognitive abilities, creativity, and critical thinking skillsRecently uploaded (20)
Describing and Interpreting an Immersive Learning Case with the Immersion Cub...
Describing and Interpreting an Immersive Learning Case with the Immersion Cub...
Equivariant neural networks and representation theory
Equivariant neural networks and representation theory
The binding of cosmological structures by massless topological defects
The binding of cosmological structures by massless topological defects
ESA/ACT Science Coffee: Diego Blas - Gravitational wave detection with orbita...
ESA/ACT Science Coffee: Diego Blas - Gravitational wave detection with orbita...
Immersive Learning That Works: Research Grounding and Paths Forward
Immersive Learning That Works: Research Grounding and Paths Forward
aziz sancar nobel prize winner: from mardin to nobel
aziz sancar nobel prize winner: from mardin to nobel
20240520 Planning a Circuit Simulator in JavaScript.pptx
20240520 Planning a Circuit Simulator in JavaScript.pptx
Applied Science: Thermodynamics, Laws & Methodology.pdf
Applied Science: Thermodynamics, Laws & Methodology.pdf
The cost of acquiring information by natural selection
The cost of acquiring information by natural selection
waterlessdyeingtechnolgyusing carbon dioxide chemicalspdf
waterlessdyeingtechnolgyusing carbon dioxide chemicalspdf
THEMATIC APPERCEPTION TEST(TAT) cognitive abilities, creativity, and critic...
THEMATIC APPERCEPTION TEST(TAT) cognitive abilities, creativity, and critic...
Seamless steel pipe
- 1. WANSTEEL GROUP https://sdwansteelpipe.com/products/seamless-steel-pipe/ https://sdwansteelpipe.com/products/seamless-steel-pipe/ WANSTEEL GROUP Seamless steel pipe (SMLS) is formed by drawing a solid billet over a piercing rod to create the hollow shell, without welding or seam. It is suitable for bending and flanging. The most advantage is increasing the ability of withstanding higher pressure. So it is widely used for boiler and pressure vessel, automotive area, oil well, and equipment components. Seamless steel pipe can be cut, threaded or grooved. And the coating method includes black / red lacquer, varnish painting, hot dip galvanization, etc. Seamless Steel Pipe Chemical Composition: Grade Ni Cr Mo Fe Cu Mn C Si Al S P Others UNS N04400 63 min. 2.5 max. 28.0-34.0 2.0 max. 0.3 max. 0.5 max. 0.024 max. UNS N06600 72.0 min. 14.0-17.0 6.0-10.0 0.5 max. 1.0 max. 0.15 max. 0.5 max. 0.015 max. UNS N06690 58.0 min. 27.0-31.0 7.0-11.0 0.5 max. 0.5 max. 0.05 max. 0.5 max. 0.015 max. UNS N06693 remainder27.0-31.0 2.5-6.0 0.5 max. 1.0 max. 0.15 max. 0.5 max. 2.5-4.0 0.01 max. Ti: 1.0 max. UNS N06625 58.0 min. 20.0-23.0 8.0-10.0 5.0 max. 0.5 max. 0.1 max. 0.5 max. 0.4 max. 0.015 max. 0.01max. Nb+Ta: 3.15-4.15Co: 1.0 max.Ti: 0.40 max. UNS N08800 30.0-35.0 19.0-23.0 39.5 min. 0.75 max. 1.5 max. 0.1 max. 1.0 max. 0.15-0.6 0.015ma. UNS N08825 38.0-46.0 19.5-23.5 2.5-3.5 22.0 min. 1.5-3.0 1.0 max. 0.05 max. 0.5 max. 0.2 max. 0.03 max. UNS N08028 30.0-34.0 26.0-28.0 3.0-4.0 remainder 0.6-1.4 2.5 max. 0.03 max. 1.0 max. 0.03 max. 0.03 max. UNS N08926 24.0-26.0 19.0-21.0 6.0-7.0 remainder 0.5-1.5 2.0 max. 0.02max. 0.5 max. 0.01 max. 0.03 max. N2: 0.15-0.25 UNS N08904 23.0-28.0 19.0-23.0 4.0-5.0 remainder 1.0-2.0 2.0 max. 0.02 max. 1.0 max. 0.035ma. 0.045 max. UNS N10276 remainder15.0-16.515.0-17.0 4.0-7.0 1.0 max. 0.01 max. 0.08max. 0.01 max. 0.015 max Co: 2.5 max.W: 3.0-4.0V: 0.1-0.3