The One Series Safety Transmitter was designed with features that simplify installation, improve productivity, and eliminate nuisance trips. “I Am Working” sensor diagnostics with redundant data processing detect open, shorted, and plugged sensing elements. The transmitter’s analog output conforms to the NAMUR NE 43 standard and provides process variable (PV) and detected-fault information. Discrete outputs provide a fail-safe (open) emergency shutdown when a fault is detected. Set point and deadband (reset point) are 100% programmable. The instrument is password protected to prevent unwanted parameter changes; eliminating the risk of tampering. In addition, LED backlighting enhances viewing of process variables, parameters, and status in dimly lit areas.
Thermal dispersion mass flow transmitters measure mass flow by detecting heat dissipation from a heated surface. The sensor contains two mass balanced elements with precision matched RTDs. The reference sensor measures the process temperature (up to +400° F [+200° C]); the second RTD measures the temperature of the heated sensor. The power to the heater is varied to maintain a constant temperature difference above the reference temperature.
There is an inherent non-linear relationship between power and mass flow. A microprocessor compares the power against the calibration curve and converts the power requirements to the mass flow rate. Temperature is also measured to provide temperature compensation of the mass flow over the operating range of the instrument.
Series One Safety Transmitter, Pressure and Temperature SwitchIves Equipment
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
Smarter, self-diagnostic digital safety switches for temperature, pressure, flow, and level eliminate some of the risks associated with mechanical or pneumatic actuated devices.
The 212 Heat Calculator is designed to measure the energy consumed in hot water heating systems and chilled water
cooling systems. The 212 will interface with a wide range
of flowmeters, including vortex and magnetic flowmeters with pulse outputs, positive displacement and inferential water meters, turbine and paddle wheel flowmeters.
Data Acquisition Equipment for Automation and Process ControlMiller Energy, Inc.
Power generation, process automation, and factory automation in manufacturing industries require rigorous, continuous monitoring in the control room. Yokogawa's DX series recorders are purpose-built data acquisition systems designed for industrial automation.
One Series Safety Transmitter - Pressure and Temperature Transmitter-SwitchMiller Energy, Inc.
The One Series Safety Transmitter simplifies installation, improves productivity, and eliminates nuisance trips. Sensor diagnostics with redundant data processing detect open, shorted, and plugged sensing elements.
Thermal dispersion mass flow transmitters measure mass flow by detecting heat dissipation from a heated surface. The sensor contains two mass balanced elements with precision matched RTDs. The reference sensor measures the process temperature (up to +400° F [+200° C]); the second RTD measures the temperature of the heated sensor. The power to the heater is varied to maintain a constant temperature difference above the reference temperature.
There is an inherent non-linear relationship between power and mass flow. A microprocessor compares the power against the calibration curve and converts the power requirements to the mass flow rate. Temperature is also measured to provide temperature compensation of the mass flow over the operating range of the instrument.
Series One Safety Transmitter, Pressure and Temperature SwitchIves Equipment
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
Smarter, self-diagnostic digital safety switches for temperature, pressure, flow, and level eliminate some of the risks associated with mechanical or pneumatic actuated devices.
The 212 Heat Calculator is designed to measure the energy consumed in hot water heating systems and chilled water
cooling systems. The 212 will interface with a wide range
of flowmeters, including vortex and magnetic flowmeters with pulse outputs, positive displacement and inferential water meters, turbine and paddle wheel flowmeters.
Data Acquisition Equipment for Automation and Process ControlMiller Energy, Inc.
Power generation, process automation, and factory automation in manufacturing industries require rigorous, continuous monitoring in the control room. Yokogawa's DX series recorders are purpose-built data acquisition systems designed for industrial automation.
One Series Safety Transmitter - Pressure and Temperature Transmitter-SwitchMiller Energy, Inc.
The One Series Safety Transmitter simplifies installation, improves productivity, and eliminates nuisance trips. Sensor diagnostics with redundant data processing detect open, shorted, and plugged sensing elements.
Magnetrol TA2 Thermal Mass Flow Meter for Flare Gas ApplicationsMiller Energy, Inc.
Low flow sensitivity means high reliability for flare gas applications. The Thermatel® TA2 thermal dispersion mass flow meter provides reliable mass flow measurement for flare gas applications to comply with monitoring requirements.
Thermatel products are in service worldwide in many of the most demanding applications.As a flow switch Thermatel is used for gas and liquid applications for both flow and no/low flow detection. Typical applications involve pump protection, cooling air/water,relief valve monitoring,exhaust flows and lubrication systems. Thermatel products provide outstanding low flow sensitivity with high range ability.
GE Advanced Modular Calibrator for Process Measurement InstrumentsFlow-Tech, Inc.
The DPI 620 Genii is an easy to use, rugged, and highly accurate multifunction instrument for calibrating & maintaining process instrumentation. Its modular design and functionality means it can be expanded over time and tailored to applications as needs change. With options that include HART / Fieldbus / Profibus communications, it’s a powerful, simple to use and high accuracy calibrator.
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
Datasheet Fluke Hydra Series III. Hubungi PT. Siwali Swantika 021-45850618PT. Siwali Swantika
Datasheet Fluke 2638A. Datasheet Fluke Data Acquisition. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Thermal dispersion switch for flow, level, interface, or temperatureFlow-Tech, Inc.
FCI liquid level/interface switches feature thermal dispersion technology in which the temperature difference between the two RTDs is greatest in the absence of liquid and decreases when the level element is submerged, cooling the heated RTD.
FCI flow switches feature thermal dispersion technology in which the temperature difference is greatest in a no-flow condition and decreases as flow increases, cooling the heated RTD. Changes in flow velocity directly affect the extent to which heat dissipates and, in turn, the magnitude of the temperature difference between the RTDs.
Siemens Terminal Box Controller (APOGEE Automation System )CONTROLS & SYSTEMS
In This PPT we are discussed about complete details of that product (Use,Operation, Technical details, Dimensions, Wiring, and etc..)
Please Support us and Follow our other Sites
https://www.instagram.com/controlsandsystems.offical
https://twitter.com/ControlsSystems
https://automationtechplc2.blogspot.com
https://humidificationcontrol.blogspot.com
https://controlsandsystems.business.site
www.controls.systemsdm@gmail.com
If you enjoyed this article, share it with your friends and colleagues
Datasheet Fluke 5502A. Hubungi PT. Siwali Swantika 021-45850618PT. Siwali Swantika
Datasheet Fluke 5502A Multi-product Calibrator. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Datasheet Fluke 5522A. Hubungi PT. Siwali Swantika 021-45850618PT. Siwali Swantika
Datasheet Fluke 5522A Multi-product Calibrator. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Process Digital Bargraph Display for Industrial Control and AutomationClassic Controls, Inc.
Commercial bargraphs are designed for use in non-nuclear environments. They may be used as HI-LO, on/off, or differential gap controllers and/or annunciators in process or other control applications. Fully programmable, these are the preferred choice for new applications, or for replacement of set point controllers, switchboard meters, other common size indicators.
Turbine flow meters for gas service from HofferFlow-Tech, Inc.
Hoffer Flow Controls manufactures high precision turbine flowmeters for the cryogenic industry and is the world leader in turbine flowmeter technology for the measurement of clean liquids and gases throughout the processing industries.
Liquisys M CPM223/253. pH/ORP Measurement. Transmitter for analog and digital glass and ISFET sensors. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
Safe and SterileThe 48 TuBore Series is the Habonim line of clean ball valves for the pharmaceutical and bioprocessing industries. These valves are designed for applications which require maximum flow capacity at minimum pressure drop, where sterility, clean-ability and drain-ability are essential for faultless product quality. The 48 TuBore valve port matches tube ID dimensions, provides tight shutoff and has exceptional performance in many service applications
Integrated features:
Tube bore
Soft parts are FDA approved
Low ferrite
Low sulphur
Outstanding metal surface finish. A fully encapsulated body seal provides an improved seal under fluctuating temperatures and pressures
Magnetrol TA2 Thermal Mass Flow Meter for Flare Gas ApplicationsMiller Energy, Inc.
Low flow sensitivity means high reliability for flare gas applications. The Thermatel® TA2 thermal dispersion mass flow meter provides reliable mass flow measurement for flare gas applications to comply with monitoring requirements.
Thermatel products are in service worldwide in many of the most demanding applications.As a flow switch Thermatel is used for gas and liquid applications for both flow and no/low flow detection. Typical applications involve pump protection, cooling air/water,relief valve monitoring,exhaust flows and lubrication systems. Thermatel products provide outstanding low flow sensitivity with high range ability.
GE Advanced Modular Calibrator for Process Measurement InstrumentsFlow-Tech, Inc.
The DPI 620 Genii is an easy to use, rugged, and highly accurate multifunction instrument for calibrating & maintaining process instrumentation. Its modular design and functionality means it can be expanded over time and tailored to applications as needs change. With options that include HART / Fieldbus / Profibus communications, it’s a powerful, simple to use and high accuracy calibrator.
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
Datasheet Fluke Hydra Series III. Hubungi PT. Siwali Swantika 021-45850618PT. Siwali Swantika
Datasheet Fluke 2638A. Datasheet Fluke Data Acquisition. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Thermal dispersion switch for flow, level, interface, or temperatureFlow-Tech, Inc.
FCI liquid level/interface switches feature thermal dispersion technology in which the temperature difference between the two RTDs is greatest in the absence of liquid and decreases when the level element is submerged, cooling the heated RTD.
FCI flow switches feature thermal dispersion technology in which the temperature difference is greatest in a no-flow condition and decreases as flow increases, cooling the heated RTD. Changes in flow velocity directly affect the extent to which heat dissipates and, in turn, the magnitude of the temperature difference between the RTDs.
Siemens Terminal Box Controller (APOGEE Automation System )CONTROLS & SYSTEMS
In This PPT we are discussed about complete details of that product (Use,Operation, Technical details, Dimensions, Wiring, and etc..)
Please Support us and Follow our other Sites
https://www.instagram.com/controlsandsystems.offical
https://twitter.com/ControlsSystems
https://automationtechplc2.blogspot.com
https://humidificationcontrol.blogspot.com
https://controlsandsystems.business.site
www.controls.systemsdm@gmail.com
If you enjoyed this article, share it with your friends and colleagues
Datasheet Fluke 5502A. Hubungi PT. Siwali Swantika 021-45850618PT. Siwali Swantika
Datasheet Fluke 5502A Multi-product Calibrator. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Datasheet Fluke 5522A. Hubungi PT. Siwali Swantika 021-45850618PT. Siwali Swantika
Datasheet Fluke 5522A Multi-product Calibrator. Informasi lebih detail hubungi PT. Siwali Swantika, Jakarta Office : 021-45850618 atau Surabaya Office : 031-8421264
Process Digital Bargraph Display for Industrial Control and AutomationClassic Controls, Inc.
Commercial bargraphs are designed for use in non-nuclear environments. They may be used as HI-LO, on/off, or differential gap controllers and/or annunciators in process or other control applications. Fully programmable, these are the preferred choice for new applications, or for replacement of set point controllers, switchboard meters, other common size indicators.
Turbine flow meters for gas service from HofferFlow-Tech, Inc.
Hoffer Flow Controls manufactures high precision turbine flowmeters for the cryogenic industry and is the world leader in turbine flowmeter technology for the measurement of clean liquids and gases throughout the processing industries.
Liquisys M CPM223/253. pH/ORP Measurement. Transmitter for analog and digital glass and ISFET sensors. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
Safe and SterileThe 48 TuBore Series is the Habonim line of clean ball valves for the pharmaceutical and bioprocessing industries. These valves are designed for applications which require maximum flow capacity at minimum pressure drop, where sterility, clean-ability and drain-ability are essential for faultless product quality. The 48 TuBore valve port matches tube ID dimensions, provides tight shutoff and has exceptional performance in many service applications
Integrated features:
Tube bore
Soft parts are FDA approved
Low ferrite
Low sulphur
Outstanding metal surface finish. A fully encapsulated body seal provides an improved seal under fluctuating temperatures and pressures
Companies in the process industry need the ability to visually monitor liquid levels in vessels (boilers, storage tanks, processing units, etc.). Traditionally, armored glass sight gauges have been used. However, many companies want an alternative to sight gauges to avoid problems such as breakage, leaks, or bursting at high pressures and extreme temperatures. In addition, the visibility of the sight glass can be poor and often affected by moisture, corrosion, or oxidation.
Magnetic level indicators (MLIs) do not have the shortcomings of glass sight gauges and are suitable for a wide variety of installations.
Control Valves for the Power Generation Industry" A Product and Applications ...Belilove Company-Engineers
TrimTeck, a USA manufacturer of industrial control valves, put together this outstanding explanation of where and how control valves are used in a power generation facility.
Modular fired heaters - A presentation by Esteem Projects at Refining India ...Tanveer Singh
Modular construction of Fired Heaters can help in saving both time and cost. This presentation touches the topic from the Indian perspective and how it can also be helpful in revamps.
For any details, please visit us at https://www.esteemprojects.com.
Thanks,
Esteem Projects Pvt. Ltd.
This is a slide show presentation I prepared for the Technical Support staff at Topcon Medical Systems to introduce and familiarize the art of refraction.
Fired heaters are used for heating hydrocarbons fluids in the refineries and petrochemical plants. They are used for high temperature heat transfer. In most fired heaters, we are burning fuel gas as source of heat . There are many heaters in the world where liquid fuel is also burnt in the fired heaters to provide the energy, but their number is decreasing due to tighter pollution laws. Heaters that are processing hydrocarbons services are prone to coking and cracking depending upon the nature of the hydrocarbons being processed. Typically heaters may run length of anywhere from 3 months for coking service to 6 years for different services. Heater designers and operators are always faced with the challenge of providing uniform heat transfer to all the tubes. Engineers use equations that assume uniform heat transfer to heater tubes When designing fired heaters. However, in reality, most fired heaters do not experience uniform heat transfer, and as a result, hot spots develop on the tubes. These hot spots cause coking inside the tubes which requires the heater be shutdown periodically to remove the coke and clean the tubes. Any shutdown to clean the tubes in a fired heater causes a substantial production loss. The owners want to extend the run length of fired heaters. Furnace Improvements has developed a new patented firing technology that provides uniform heat transfer to heater tubes. This technology can be applied to most fired heaters. Our patented technology reorients the burners at a slight angle away from the tubes. We are able to direct the hottest part of the flames and flue gases away from the tubes without affecting the heat transfer in any way. FIS has installed this in 5 heaters ranging from 14 MMBtu/hr. to 280 MMBtu/hr. The clients are experiencing significant reduction in tube metal temperatures. This is translating into lower coking rates and higher tube life. We have been able to increase the capacity of the heaters in most of the cases. In one of the case study that has been presented in this heater, the heater duty was increased from 14 MMBtu/hr. to 21 MMBtu/hr. Inclined firing improves the heat transfer to the tubes and makes in uniform.
Get 4 channel, 8 channel, 16 channel temperature scanner - Canopus Instrumentssmita_kale
Canopus Instruments are Manufacturers and suppliers of Load Cell Amplifiers in India. They manufacture best quality of load cell amplifier, load cell amplifier module, load cell amplifiers in India. https://www.canopusinstruments.com/product-category/industrial-automation-product/resistance-temperature-detector-scanner/
Mitsubishi digital protection relay melpro a series dienhathe.vnDien Ha The
Thiết Bị Điện Mitsubishi, Thiết Bị Điện,
Điện Công Nghiệp Mitsubishi, Điện Công Nghiệp,
Điện Hạ Thế Mitsubishi, Điện Hạ Thế,
Điện Dân Dụng Mitsubishi, Điện Dân Dụng,
Mitsubishi,
Thiết Bị Đóng Cắt Mitsubishi, Thiết Bị Đóng Cắt,
Thiết Bị Điện Mitsubishi, Thiết Bị Điện,
The SIPROTEC Compact 7RW80 is a numerical, multifunction relay for connection to voltage transformers. It can be used in distribution systems, on transformers and for electrical machines. If the SIPROTEC Compact 7RW80 detects any deviation from the permitted voltage, frequency or over excitation values, it will respond according to the values set. The relay can also be applied for the purposes of system decoupling and for load shedding if ever there is a risk of a system collapse as a result of inadmissibly large frequency drops.
Moore Industries is proud to announce the new SFY Functional Safety Frequency-to-DC Transmitter with display including SIL 3 capability. The 2-wire (loop-powered) SFY is ideal for use in your Safety Instrumented System (SIS) in a wide range of process and factory automation monitoring applications and as part of the FS Functional Safety Series providing reliable and accurate monitoring of frequency or pulse signals in SIS. The SFY is approved for single use in SIS up to SIL 2 and in a redundant architecture (1oo2, 2oo3, etc.) up to SIL 3.
(http://www.novatek-electro.in) Novatek Electro is specializing in the development and the subsequent manufacturing implementation of Programmable Power Electronics, Instrumentation or so called general purpose and special-purpose Intelligent Electronic Systems (IGM’s). This kind of electronics finds application in producing next generation switching protection devices, apparatus for monitoring, control and metering, protective relaying devices and automatic equipment, technology controllers etc.
Data Teknis Gossen Metrawatt Installation Tester : PROFITEST PRIME | PRIME ACPT. Siwali Swantika
Pemesanan produk, hubungi PT Siwali Swantika melalui WhatsApp, Jakarta : 0811-1519-949 (chat only) | Surabaya : 0811-1519-948 (chat only). Kunjungi website kami di www.siwali.com, untuk detail informasi spesifikasi dan model alat.
Programmable Limit Alarm Trips with Intrinsically-Safe Field ConnectionsArjay Automation
The universal SPA2IS Programmable Limit Alarm Trips provide on/off control, warn of unwanted process conditions, alarm on rate-of-change and provide emergency shutdown. Very versatile, they accept signal inputs from transmitters and temperature
sensors that are located in hazardous areas where the method of protection implemented by the plant or facility is Intrinsic Safety.
Siemens ,
Catalog Thiết Bị Điện Siemens , Catalog Thiết Tự Động
Catalog Phụ Kiện Siemens , Catalog Phụ Kiện,
Catalog Siemens , Catalog,
https://www.dienhathe.com,
Chi tiết các sản phẩm khác của Siemens tại https://dienhathe.com
Xem thêm các Catalog khác của Siemens tại https://dienhathe.info
Để nhận báo giá sản phẩm Siemens vui lòng gọi: 0907.764.966
Yokogawa’s new TDLS8000 houses all of the industry’s leading features in one robust device.
The platform design is for in situ measurements which negate the need for sample extraction and conditioning.
The non-contacting sensor allows for a variety of process types including corrosive, abrasive and condensing.
The first generation platform has been proven in many others for the measurements of O2, CO, CH4, NH3, H2O and many more NIR absorbing gases.
This second generation platform has improved reliability and ease of installation and maintenance while still meeting or exceeding designed application demands.
Explore the compact inverter WJ200 series built for excellent performance and user-friendliness.
To learn more about Hitachi Inverters, visit: https://www.hitachi-iesa.com/ac-drives-inverters
Process Control Instruments India - Canopus Instrumentssmita_kale
Canopus Instruments manufactures top quality instrumentation and process control products. Buy the best industry products at Canopus Instruments now. https://www.canopusinstruments.com/product/industrial-automation-product/process-controller-indicators/digital-process-indicator/
Similar to Safety Transmitters for Temperature and Pressure (20)
Flow & Pressure Instrumentation for Biopharmaceuticals & Life SciencesMiller Energy, Inc.
Producing biopharmaceuticals is one of the world’s most demanding manufacturing processes. Brooks Instrument’s mass flow and pressure control technology helps maximize cell culture yields and control bioprocess costs. Brooks flow and pressure controllers set global standards for reliability, repeatability and long-term stability.
Magnetrol Guide Wave Radar Level Transmitter For Hygienic ApplicationsMiller Energy, Inc.
For hygienic applications, the transmitters are available with a 304 stainless steel housings designed specifically for use in facilities with the special requirements for the wetted and non-wetted materials, process connections and surface finishes of hygienic industries.
Solenoid Valves for Water Conditioning and Purification Systems and EquipmentMiller Energy, Inc.
New composite valve technologies can offer notable benefits
when improved valves are specified for membrane-based filtration like reverse osmosis systems. Advantages include current certifications, ready availability, high reliability in challenging applications, ease of installation and use, and a choice of normally open and normally closed versions
Special RTD Temperature Sensor Configuration for Heat Trace ApplicationsMiller Energy, Inc.
Heat traced piping requires a means of temperature measurement to assure control of heat input to minimize energy consumption and maximize pipe and fluid temperature.
Maintenance Procedures for Yokogawa ADMAG TI Series AXW Magnetic Flow MeterMiller Energy, Inc.
The AXW series is ideal for industrial process lines, and water supply and sewage applications. With outstanding reliability and ease of operation, developed on decades of field-proven experience, the AXW will increase user benefits while reducing total cost of ownership.
Regulatory modifications have raised important issues in design and use of industrial safety systems. Certain changes in IEC 61508, now being widely implemented, mean that designers and users who desire full compliance must give new consideration to topics such as SIL levels and the transition to new methodologies.
Eclipse Model 706 High Performance Guided Wave Radar Level TransmitterMiller Energy, Inc.
The Eclipse® Model 706 high performance transmitter is a loop-powered, 24 VDC level transmitter that is based upon the proven and increasingly accepted technology of guided wave radar (GWR). Encompassing a number of significant engineering accomplishments, this leading edge level transmitter is designed to provide measurement performance well beyond that of many of the more traditional technologies.
Schubert & Salzer is a fast growing high-tech company, that develops, produces and distributes highly precise control and stop valves which are applied in the process industry.
Achieve superior accuracy and unmatched zero stability in ultra-low-flow gas and liquid measurement and control with the Quantim® Coriolis mass flow controllers and meters from Brooks Instrument. Brooks has taken the lead in driving improvements in Coriolis flow technology: Our patented Coriolis sensor design measures low flows independent of fluid type or process variables. The result: unsurpassed performance - the most accurate, stable, repeatable and reproducible mass flow measurement and control, even under changing conditions.
Verbatim Gateway is a field-proven, stand-alone alarm monitoring and reporting solution. More reliable than PC-based alarm systems, you can depend on it to perform in mission-critical applications due to its fault tolerance and internal battery backup. Robust yet affordable, Verbatim Gateway monitors operations and notifies personnel of problem conditions — anytime, anywhere — for a one-time cost. No extra service contracts or plug-ins required!
Parker manufactures one of the widest offerings of quick connect hose fittings available, with variants, options, and specialized products to suit almost every application.
Rugged, NEMA 4X, epoxy coated enclosure
SPDT or DPDT switch output
Easy access wiring
Single switch output
Internal reference scale and adjustable deadband available
Adjustable ranges: ◦30 "Hg Vac to 5000 psi
• 1 bar Vac to 344 bar
• 0.2 "wcd to 500 psid
• 0,5 mbar d to 34,5 bar d
• -180 to 650 ºF
• -117 to 340ºC
Approvals: UL, CSA, CE, TUV
A straight forward device, the current to pneumatic converter produces a pneumatic output signal that is proportional to an electrical control level input signal of 4 to 20 mA or 10 to 50 mA. This provides a useful interface between electronic controllers and pneumatically operated valves, air cylinders, or other air operated control elements.
The Vanguard WirelessHART gas detector is ideal for the monitoring of toxic and combustible gases without the need for costly and fixed wiring. With a five year battery life and one button calibration, the Vanguard detector is easy to operate and maintain.
Each Vanguard detector has a WirelessHART transceiver, an antenna, a display, a long life power module, a gas sensor, and a signal processor for the gas sensor. Vanguard uses a sensor architecture trademarked “Flexsense,” which allows the sensor to identify its target gas and self-configure to a Vanguard transmitter upon connection.
Magnetrol is a globally recognized manufacturer of level and flow measurement instrumentation and devices. Technologies include inferential and direct measurement.
Making the best instrument selection for a flow measurement application should include an assessment of what the operators really need in order to safely and effectively run the process or perform the task related to the measurement of fluid flow.
Habonim Valves & Actuators is a leading manufacturer of ball valves and pneumatic actuators with over 50 years' experience and a worldwide reputation for its high quality, innovation and engineering expertise. Habonim supplies a wide range of 3-piece and flanged ball valves, as well as tailor-made solutions, generating significant cost and space savings for its customers.
Magnetrol International has launched the PULSAR Model R86 Non-Contact Radar transmitter, an advanced level control solution that offers radar technology with improved performance for a wide range of level measurement applications.
The PULSAR Model R86 is designed to provide
outstanding accuracy, reliability and safety for
virtually all process industries.
Utilizing an Aluminum Oxide sensor 600 times more sensitive than conventional sensors
The 8800 series uses field proven aluminum oxide (Al2O3) sensing technology to accurately detect trace moisture on either a continuous or spot checking basis.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
1. • Improve Availability with reduced nuisance trips
• Improve Uptime with safety diagnostics
• Improve Safety with SRO to ensure safety function
• Lower Inventory a transmitter, switch and gauge in one
• Simplify Complex Safety Systems with SFF = 98.8%
• Reduce Migration Costs with backward and forward
compatibility
• Certified for Use in SIL 2 functional safety systems per
IEC 61508
o n e S e r i e s S t - B - 0 1
One Series safety Transmitter
pressure and temperature transmitter-switch
RoHScompliant
LEADERS IN SAFETY, ALARM & SHUTDOWN
DUAL SEAL
CERTIFIED
2. 2 w w w . u e o n l i n e . c o m One Series ST- B -01
The One Series Safety Transmitter is a transmitter-switch for monitoring
pressure or temperature and meets the requirements of SIL 2 for random
integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for
systematic capability. The One Series Safety Transmitter incorporates UE’s
patented IAW self diagnostics, redundant and diverse signal processing and
software algorithms to detect abnormalities in the process and internal faults.
The design is based on a powerful microprocessor that provides an extremely
fast response time for emergency shutdown situations.
Some applications require a local switch that is capable of initiating an
emergency shutdown at the point of measure. This avoids any time lag that
may occur by sending a signal to a safety PLC and having the PLC initiate the
shutdown. This practice can take several (precious) milliseconds. Unique to
UE One Series transmitters, the One Series Safety Transmitter can provide the
shutdown directly in less than 100 milliseconds, ideal for positive displacement
pump applications (for example). This high-capacity safety relay output (SRO)
with programmable set point and deadband, handles high voltages and current
to actuate a control valve or shut down a compressor directly and rapidly,
something a transmitter alone cannot do.
UE is aware that not all Safety Instrumented System (SIS) applications require
an emergency shutdown when abnormal conditions are detected. For this
reason, the One Series Safety Transmitter provides additional logic outputs for
use in voting logic schemes that may be used to report warnings prior to a
shutdown. This feature provides the SIS design engineers with the ability to
balance the need to provide a safe working environment with the need to keep
the process running - but only if conditions permit it.
The combination of features like no moving parts and IAW (I Am Working)
self-diagnostics provide a highly reliable, accurate and repeatable monitor for
detecting pressure and temperature process variables and making intelligent
switch decisions based on retained settings and the process conditions. The
IAW feature provides a solution to the “blind device” issue common with
mechanical apparatus. The health status of the One Series Safety Transmitter
is communicated via the display, 4-20 mA analog signal and IAW status outputs.
If a fault is detected, the 4-20 mA signal will output <3.6 mA, compliant to the
NAMUR NE 43 standard. Simultaneously, the IAW status signal will change state.
By monitoring both signals, redundant methods of fault detection are provided,
independent of the process variable.
The One Series Safety Transmitter provides an explosion-proof type 4X/IP66,
weather-tight enclosure suitable for harsh environments and hazardous (Class
I, Division 1, Zone 1) locations and allowing the One Series Safety Transmitter
to be mounted outside. Repeatability of 0.1% of maximum range rivals
transmitters that cost much more than the One Series Safety Transmitter.
Combined, these features provide an extremely accurate Safety Relay Output
(SRO) set point that will not drift over time.
Model 2SLP is loop-powered and operates in a transmitter loop attached to
an analog PLC or DCS input and provides a field-scalable 4-20 mA signal over
a 2-wire connection. Model 2SLP contains an auxiliary solid-state relay switch
rated for 12 - 250 VAC at 5 amperes.
The set point and deadband (hysteresis) of the Safety Relay Output is fully
programmable over the entire range of the sensor. Reaction time for the One
Series Safety Transmitter to a process change is less than 100 milliseconds -
switch outputs only with delay set to "OFF".
overview features
• Digital process display
• Programmable set point and deadband
• Self-diagnostic solid-state digital
electronics
• Plug port detection
• Adjustable nuisance trip dampening
• Configurable IAW® self-diagnostics
• Min/Max process values memory
• 3-year warranty
• Provide a SFF = 98.8
3. w w w . u e o n l i n e . c o m 3One Series ST- B -01
ONE Series Safety Transmitter
The One Series Safety Transmitter process display module features a large, easy-to-read back-lit LCD display, showing the process variable and the health
status of the instrument. (See Display Features for a complete description.) Set point, deadband and minimum/maximum process values can be easily
accessed from the front of the unit after the locking cover is removed. Programming and interrogating the One Series Safety Transmitter is done through
two buttons on the faceplate, providing easy setup and an added level of security from hackers and tampering. No remote hand-held programming device
is required.
process display module
The One Series Safety Transmitter model 2SLP incorporates a Safety Relay Output (SRO) to provide a high-capacity switch rating of 240 VAC at up to 5
amperes. The SRO may be used to provide an emergency shutdown signal locally, at the point of measure, to external equipment such as a motor control
center (MCC) or electrically actuated valve positioner. The state of the SRO (open or closed) may be monitored with a logic solver using the SRO Status
output.
High-Power Safety Relay Output
Shown with spring-loaded
RTD sensor
Shown with differential
pressure sensor
Shown with gage
pressure sensor
Shown with dual seal and
gage pressure sensor
4. 4 w w w . u e o n l i n e . c o m One Series ST- B -01
For alarm and shutdown switching applications, there is no better choice than the One Series family of electronic switches
from United Electric Controls. Measuring gauge pressure, differential pressure or temperature, the extremely rugged and
reliable One Series takes all of the guess-work out of monitoring process variables to prevent injury, loss and downtime.
With its large digital display, fully-adjustable deadband, and 100% solid-state design, the One Series is the obvious choice
for plant upgrades and new construction projects. A built-in microprocessor includes digital repeatability and intelligent
self-diagnostics, offering plant operators an extremely reliable and smart protection device.
application versatility
Proven in use in literally thousands of diverse applications, UE's explosion-
proof One Series models extend this revolutionary switching technology to
Zone 1 (Division 1) areas.
Here are just a few applications:
• Safety systems – meets the requirements of SIL 2 for random integrity at
HFT = 0, SIL 3 for random integrity at HFT = 1and SIL 3 for systematic
capability.
• FMEDA report available upon request
• Pumps and compressors – start/stop, emergency shutdown
• Lubricating oil monitoring – sump temperature, bearing pressure,
predictive maintenance
• Hydraulic oil pressure – high pressure monitoring, emergency shutdown,
low pressure alarm
• Filter monitoring – change indication, proving flow
• Plant upgrades – power and wastewater plant upgrades, drop-in
replacement for mechanical switches
The One Series and
other switches
monitoring lube o
on a gear box.
exida® is a registered trademark of exida Consulting LLC.
5. w w w . u e o n l i n e . c o m 5One Series ST- B -01
ONE Series Safety Transmitter
Power input/
Switch output:
Model Input Type (Range) Max Switch Ratings (SPST)
2SLP47
2-Wire 24 VDC analog
input loop powered (20-40
VDC) @ 4-20 mA
12-250 VAC @ 5.0 A
Accuracy: 0.5% of full range span, at room temperature
Repeatability: 0.1% of full range span
Ambient operating
temperature range:
Display operating
temperature range:
10°F (-12°C) 158°F (70°C)
specifications
Approved Ambient Operating Temperature Range
cULus (Division System) cULus & ATEX (zone System)
2SLP -40°f (-40°C) 158°f (70°C) -40°f (-40°C) 158°f (70°C)
d
oil
6. 6 w w w . u e o n l i n e . c o m One Series ST- B -01
Long-term stability: ±0.25% of range/year maximum
Temperature drift: 0.03% of full scale per °C (0.06% for the K10 range)
Compensated temperature range for P10, K10 range is -20°C to 50°C
Switch response time: “Change-of-output” response ≤ 100 mS (for detection of full step change and change
of output state, delay feature off)
Display response time: 400 mS (2.5 Hz)
Transient filtering: Programmable time constants between 250 mS and 2 seconds in 2X increments
Diagnostics (IAW®): Open or shorted sensor; plugged port; power supply out of range; over and under-
range conditions; microprocessor faults/failure; keypad short; switch fault
Control modes: Field-configuration for SRO switch action with programmable manual reset
Mode Action Fault
Open Rise Open on rising media Open
Open Fall Open on falling media Open
Window Open outside window Open
Analog output: Compliant to NAMUR NE 43 4-20 mA output, 360 ohms max. at 24 VDC, Field
scalable, 2:1 turn down. Various faults are indicated at <3.6 mA. See installation
manual for details.
Safety Relay Output Set point &
deadband:
User-configured, 100% adjustable over entire sensor operating range, deadband of 0
is undefined
Status Outputs: SRO Status - 30 VDC @ 20 mA Maximum
IAW Output - 30 VDC @ 20 mA Maximum
Enclosure: Type 4X/IP66 certified polyester painted aluminum alloy 360
Faceplate:
Cover:
UV-resistant pressure sensitive keypad and display overlay
Polyester painted aluminum with tempered glass insert
Conduit: 3/4” NPT female aluminum casting
specifications (continued)
7. w w w . u e o n l i n e . c o m 7One Series ST- B -01
ONE Series Safety Transmitter
IAW® is a registered trademark of United Electric Controls Co. Specifications subject to change without notice
Display: Backlit
• Local 4 digit x 0.5” LCD
• IAW® (I Am Working) status
• Process variable
• Units of measure
• Switch status
• Latch status
• Set point value
• Deadband value
• Min/Max values
• Fault codes
Memory: Programming and data protected by non-volatile EEPROM
Sensors: Gauge Pressure – 316L stainless steel, welded diaphragm, 1/2” NPT (female) process connection, micro-machined
piezo-resistive strain gauge silicon element, 0.25 ml silicone oil fill.
Maximum media temperature: -40 to 257°F (-40 to 125°C)
Differential Pressure - 316L stainless steel, welded diaphragms, 1/4” NPT (male) process connections, piezo-
resistive strain gauge silicon element, silicone oil fill.
Maximum media temperature: -40 to 257°F (-40 to 125°C)
Temperature – 316 stainless steel 0.25” OD sheath containing a 100 ohm 4-wire platinum RTD element available
with epoxy fill (local low temp) or powder fill (remote high temp).
Media temperature limits:
-328 to 1000°F, intermittent to 1100°F (-200 to 538°C, int. to 593°C) for TH and TT ranges
-40 to 500°F (-40 to 260°C) for TR and TL ranges
Vacuum: All pressure sensors withstand deep vacuum with no calibration effects. Two compound vacuum ranges are
available-P06 and P08 (see page 8).
EMI/RFI: Compliance to CE EMC requirements: EN 61000-6-2, EN 61000-6-4
Emission: EN 61000-6-4 Class A
Immunity: EN 61000-4-2 Immunity to Electrostatic Discharge
EN 61000-4-3 Immunity to Continuous Radiated Disturbances
EN 61000-4-4 Immunity to Electrical Fast Transients
EN 61000-4-5 Immunity to Surges
EN 61000-4-6 Immunity to Continuous Conducted Disturbances
EN 61000-4-11 Immunity to Voltage Dips and Interruptions
Weight: 4.5 - 6.0 lbs (2.0 - 2.7 kg)
Shock: per MIL-STD-810G method 516.6 – when device is subjected to 15 g (10 mSec) and 40 g (6 mSec); 3 drops/axis
Effects: less than +/- 0.40% of range
Vibration: per IEC 61298-3 (field and pipeline applications with high vibration level, 10-1000 Hz range, 0.014” displacement
peak amplitude, 5 g acceleration amplitude)
Effects: less than +/- 0.40% of range
specifications (continued)
8. 8 w w w . u e o n l i n e . c o m One Series ST- B -01
how to order
Model Description
Zone Division
0 1 2 1 2
2-wire loop-powered or 24V external powered, 4-20
mA output, programmable solid-state relay rated @
250 VAC, 5 amperes, 2 status switch outputs rated at
30 VDC, 20 mA max.
2SLP47
Build a part number by selecting the model, sensor and options from the tables below.
Sensor Pressure Operating Range1 + display resolution Maximum Over Range2
Gauge pressure, piezo-resistive strain gage, silicone oil fill, 316L stainless wetted materials, 1/2” NPT (female) process
connection, displayed as shown.
P06 -14.7 to 30 psig 831.1” wc 2068 mbar 206.8 KPa 2.109 kg/cm2 60 psig 4137 mbar
P08 -14.7 to 100 psig 2770” wc 6895 mbar 689.5 KPa 7.031 kg/cm2 200 psig 13,8 bar
P10 0-5.00 psig 138.5 “wc 344,7 mbar 34.47 KPa 0.352 kg/cm2 10 psig 690 mbar
P11 0-15.00 psig 415.5 “wc 1034 mbar 103.4 KPa 1.055 kg/cm2 30 psig 2068 mbar
P12 0-30.00 psig 831.1 “wc 2068 mbar 206.8 KPa 2.109 kg/cm2 60 psig 4137 mbar
P13 0-50.00 psig 1385 “wc 3447 mbar 344.7 KPa 3.516 kg/cm2 100 psig 6895 mbar
P14 0-100.0 psig 2770 “wc 6895 mbar 689.5 KPa 7.031 kg/cm2 200 psig 13,8 bar
P15 0-300.0 psig NA 20,68 bar 2068 KPa 21.09 kg/cm2 600 psig 41,4 bar
P16 0-500.0 psig NA 34,47 bar 3447 KPa 35.16 kg/cm2 1000 psig 68,9 bar
P17 0-1000 psig NA 68,95 bar 6895 KPa 70.31 kg/cm2 2000 psig 137,9 bar
P18 0-3000 psig NA 206,8 bar 20.68 MPa 210.9 kg/cm2 6000 psig 413,7 bar
P19 0-4500 psig NA 310,3 bar 31.03 MPa 316.4 kg/cm2 9000 psig 620,5 bar
P20 0-6000 psig NA 413,7 bar 41.37 MPa 421.9 kg/cm2 12000 psig 827,4 bar
Example: 2SLP47 P15-M041
9. w w w . u e o n l i n e . c o m 9One Series ST- B -01
ONE Series Safety Transmitter
1 - The pressure range that the sensor will perform within specified tolerances.
2 - The maximum pressure that can be applied without affecting sensor performance.
3 - The maximum pressure that can be applied to both ports simultaneously without affecting sensor performance. Pressure on the “H” sensor port must be ≥ pressure
on the “L” sensor port.
Sensor Pressure Operating Range1 + display resolution
Differential pressure, piezo-resistive strain gage, silicone oil fill, 316L stainless wetted materials, 1/4” NPT
(male) process connections, displayed as shown.
K10 0-5.000 psid 138.5 "wc 344,7 mbar 34.47 KPa 0.352 kg/cm2
K11 0-50.00 psid 1385 “wc 3447 mbar 344.7 KPa 3.516 kg/cm2
K12 0-100.0 psid 2770 “wc 6895 mbar 689.5 KPa 7.031 kg/cm2
K13 0-200.0 psid NA 13,79 bar 1379 KPa 14.10 kg/cm2
how to order cont.
Sensor Temperature Range Description (see page 13 for sensor drawings)
Temperature – 4-wire RTD, 100 Ω platinum, DIN 0.00385, 0.25” OD sensor sheath, 316 stainless steel construction
TL1
-40 to 450°F/-40 to 232°C
(See page 11 fitting options)
Local (stem) mounted rigid to enclosure, 4” sheath length
TL2 Local (stem) mounted rigid to enclosure, 6” sheath length
TL3 Local (stem) mounted rigid to enclosure, 10” sheath length
TR1 Remote mounted, 2.5” sheath, 6’ MI fixed extension length
TRC Remote mounted, 2.5” sheath, 1’ to 30’ MI extension length MUST BE SPECIFIED. USE OPTION W074 ONLY.
TH1 -40 to 1000°F/-40 to 538°C
(See page 11 fitting options)
Remote mounted, 2.5” sheath, 6’ MI fixed extension length
THC Remote mounted, 2.5” sheath, 1’ to 30’ MI extension length MUST BE SPECIFIED. USE OPTION W074 ONLY.
TC1 -300 to 200°F/-184 to 93°C
(See page 11 fitting options)
Remote mounted, 2.5” sheath, 6’ MI fixed extension length
TCC Remote mounted, 2.5” sheath, 1’ to 30’ MI extension length MUST BE SPECIFIED. USE OPTION W074 ONLY.
TTC
-40 to 900°F/-40 to 482°C
(Example: TTC–NUN6–L 10.5)
Local (stem) spring-loaded mount, NUN connection lengths: 4” – 10” in 1” increments, variable sheath (L)
length up to 60”, BOTH MUST BE SPECIFIED. Refer to drawing on page 13. Thermowell required, see page
11.
Thermowells and fittings are shown on page 11.
Sensor Maximum Over Range2 Maximum Working Pressure3
K10 10 psid 690 mbar 50 psig 3447 mbar
K11 100 psid 6895 mbar 500 psig 34,47 bar
K12 200 psid 13,8 bar 1500 psig 103,4 bar
K13 400 psid 27,6 bar 1500 psig 103,4 bar
10. 10 w w w . u e o n l i n e . c o m One Series ST- B -01
OPTION CODES
M041 Dual Seal - Provides secondary process seal for all pressure models
M201 Factory programmed set point, deadband and switch mode
(For Open on Rise or Open on Fall modes, all 3 settings are required at time of ordering - see example
below)
Set Point1 Deadband1 Switch Mode
40.00 25.00 Open on rise
(For window mode all 4 settings are required at time of ordering - see example below)
Set Point High1 Deadband High1 Set Point Low1 Deadband Low1
60.00 12.00 18.00 10.00
M270 Display units, degrees C for temperature models
M275 Display units, inches of water column
M276 Display units, bar or mbar
M277 Display units, kPa or MPa
M278 Display units, kg/cm2
M444 Paper tag
M446 Stainless steel tag
M449 Mounting bracket for pipe or wall. Use part number 6361-704 if ordered separately. See page 12 for additional
information.
M550 Oxygen cleaning service
W073 1/2” NPT male compression fitting for use with all TL and TR sensors, see page 8 for additional information
W074 1/2” NPT male union connector for use with all TR, TH and TC sensors
W081 Thermowell adapter - Adapts 3/8" Thermowell to 1/4" sensor sheath
W930 1/2” NPT male to G1/2 male adapter for use with gauge pressure sensors P06-P20. Use part number 6361-762 if
ordered separately.
W932 1/4” NPT female to G1/2 male adapter for use with differential pressure sensors K10-K13. Use part number 6361-
763 if ordered separately (2 required)
1Note: Four digits must be entered for each set point and deadband. Please refer to the display resolution chart on pages 8 & 9 for
the correct number of decimal places allowed for the sensor range and units of measure selected.
11. w w w . u e o n l i n e . c o m 11One Series ST- B -01
ONE Series Safety Transmitter
temperature sensors and fittings compatibility chart
W073 W0741.77"
Ø0.250"
2.285"
Ø0.125"
2.36"
Model (Table 1)
W073
1/2” NPT compression fitting with
ferrule to fit 0.25” sensor sheath
W074
1/2” NPT union connection to fit 0.125” sensor extension
cable
2SLP TLx TRx, THx, TCx
3/4
[19mm]
1
[25.4mm]
2 1/2
[63.5mm]
1/4
[6.4mm]
1/2 NPT
L
P Q
U
Ø.260
BORE
Ø1/2
[12.7mm]
Thermowell
UE Part #
Length (L)
Inches
Local Temperature Sensors w/
0.25” Sensor Sheath1
Remote
Temperature
Sensors w/
0.125” Diameter
MI Cable1
P (NPT) Q U TL1 (4”) TL2 (6”) TL3 (10”) TR, TH & TC
1S260L2.5-316 2.5 1/2 5/8 1 W073 W073 W073 W074
1S260 L4-316 4 1/2 5/8 2.5 NA W073 W073 W074
1S260 L4.5-316 4.5 1/2 5/8 3 NA W073 W073 W074
1S260 L5.5-316 5.5 1/2 5/8 4 NA NA W073 W074
1S260 L6-316 6 1/2 5/8 4.5 NA NA W073 W074
1S260 L6.5-316 6.5 1/2 5/8 5 NA NA W073 W074
1S260 L9-316 9 1/2 5/8 7.5 NA NA NA W074
1S260 L9.5-316 9.5 1/2 5/8 8 NA NA NA W074
1S260 L12-316 12 1/2 5/8 10.5 NA NA NA W074
1S260 L15-316 15 1/2 5/8 13.5 NA NA NA W074
1S260 L18-316 18 1/2 5/8 16.5 NA NA NA W074
1S260 L24-316 24 1/2 5/8 22.5 NA NA NA W074
2S260L2.5-316 2.5 3/4 3/4 1 W073 W073 W073 W074
2S260 L4-316 4 3/4 3/4 2.5 NA W073 W073 W074
2S260 L6-316 6 3/4 3/4 4.5 NA NA W073 W074
2S260 L9-316 9 3/4 3/4 7.5 NA NA NA W074
2S260 L12-316 12 3/4 3/4 10.5 NA NA NA W074
2S260 L15-316 15 3/4 3/4 13.5 NA NA NA W074
2S260 L18-316 18 3/4 3/4 16.5 NA NA NA W074
2S260 L24-316 24 3/4 3/4 22.5 NA NA NA W074
Note: Reference (Table 1) to determine sensor sheath diameter or the diameter of the MI cable by model
fittings for Thermowells (Table 2)
0.375 REF
0.250
REF
2.50
REF
SENSOR
THERMOWELL ADAPTER
thermowell Adapter option W081 Thermowell
12. 12 w w w . u e o n l i n e . c o m One Series ST- B -01
dimensional drawings
enclosure AND SENSOR details
2" PIPE
B
11/32 WIDE SLOTS (4 PL)
B
B
FOR PIPE MOUNTING OR
WALL MOUNTING
PIPE MOUNTING
CLAMPS
A
B
2X, 4X, 8X ENCLOSURE,
C
C
USE
MOUNTING
SCREW
(4 PL)
A
(USER SUPPLIED)
Wall or Pipe Mounting Bracket
Option M449 or part #6361-704
WARNING: The One Series unit must be
secured to a wall or pipe. Do not use the
sensor to support the instrument. Contact
UE Technical Support at 617-923-6977 or
email at techsupport@ueonline.com.
8.7"
[220.98 mm]
5.3"
[135.62 mm]
1/2 NPT
Pressure
Connection
1/8 NPT
Breather
vent
2.3"
[58.42 mm]
Shown with gauge pressure sensor and Dual Seal option M041
13. w w w . u e o n l i n e . c o m 13One Series ST- B -01
ONE Series Safety Transmitter
4.50
[114.3mm]
Ø0.250
[6.4mm]
2.50
[63.5mm]
L 2.00
[50.8mm]
4.50
[114.3mm]
Ø0.125
[3.2mm]
0.50
[12.7mm]
L
0.50
[12.7mm]
L NUN 4.50
[114.3mm]
0.25
[6.35mm]
SPRING
LOAD
TL1-TL3 Sensors
Remote sensors
TTC Sensors
Ø0.250
[6.4mm]
Ø0.250
[6.4mm] L=60”max.,NUN=4”to 10”in 1”increments
TEMPERATURE sensors
DIFFERENTIAL
Pressure SENSORS
GAUGE
PRESSURE SENSORS
1.06
[26.9mm]
1/2”-14 NPT (FEMALE)
1/4”-18 NPT (MALE)
BOTH ENDS3.0
[76.2mm]
1.06
[26.9mm]
dimensional drawings (continued)
14. 14 w w w . u e o n l i n e . c o m One Series ST- B -01
Approvals & Ratings
Model N. America
UL File# E226592
UL Listed, cUL Certified
UL 50, 50E, 1203, 60079-0, 60079-1, 61010-1
CSA C22.2 No. 25, 30, 60079-0, 60079-1, 61010-1
Europe
European Union Directive 94/9/EC (ATEX)
EN 60079-0, EN 60079-1, EN 60079-31
International
IECEx Scheme
IEC 60079-0, IEC 60079-1, IEC 60079-31
2SLP Explosion
proof/Flameproof
Class I, Groups A, B, C and D; Class II, Groups E, F, G;
Class III
Class I, Zone 1, AEx d IIC T3/T5**
Class I, Zone 1, Ex d IIC
Certificate# DEMKO 09 ATEX 0813748X Rev. 1
II 2 G Ex d IIC T3/T5**
II 2 D Ex tb IIIC T+90°C Db
IP66
Certificate# IECEx UL 08.0017
Ex d IIC T3/T5**
Ex tb IIIC T+90°C Db
IP66
**T3 for pressure sensor ranges P10-P16 only. T5 for all other models.
Specifications subject to change without notice.
15. w w w . u e o n l i n e . c o m 15One Series ST- B -01
ONE Series Safety Transmitter
additional products from ue
12 Series – Electro-Mechanical Pressure and Temperature Switch
• Dual seal compliant to ANSI/ISA 12.27.01
• Compact, cylindrical 316 stainless steel enclosure
• Hermetically-sealed SPDT or DPDT switch output
• Explosion-proof
• Snap-acting belleville spring mechanism to enhance vibration
resistance and set point stability
• Pressure ranges to 12,500 psi; DP working pressure ranges to 2500 psid;
temperature ranges to 650°F
120 Series – Electro-Mechanical Pressure and Temperature Switch
• Explosion-proof line of pressure, differential pressure, and temperature
models with wide selection of ranges, sensors and pressure connections
• UL, cUL, ATEX certified for hazardous locations
• Single or dual switch outputs
• Welded stainless steel diaphragm pressure sensor
• Internal or external set point adjustment
TX200 Series HART® & ASIC Pressure Transmitter
• Smart TX200H offers HART 7 communication and 4-20 mA output
• TX200H 10:1 range turndown helps reduce inventory
• ASIC based TX200 offers 4-20 mA output or 1-5 VDC or 0-10 VDC output
• Rugged 316 stainless steel construction, welded and hermetically sealed
• Wide variety of process connections available for pressure ranges from 0 to 15 psi
Up to 0 to 25,000 psi
117 Series – Electro-Mechanical Pressure and Temperature Switch
• Single switch for corrosive and hazardous division 2 locations
• Compact pressure, differential pressure and temperature models
• Hermetically-sealed SPDT and DPDT switch output
• Epoxy-coated, weather-tight design houses stainless steel internal
construction
• Convenient terminal block wiring
Temperature Sensors
Rugged RTDs and thermocouples for process and energy applications,
available with Nema 4X and explosion-proof heads to match heat-trace,
turbine, combustion, and stack-emission applications
DUAL SEAL
CERTIFIED
16. U.S. Sales Offices
United Electric Controls
31 Old Stage Road
Hampton Falls, NH 03844
Phone: 617-899-1132
email: northeastsales@ueonline.com
United Electric Controls
1022 Vineyard Drive
Conyers, GA 30013
Phone: 770-335-9802
email: southeastsales@ueonline.com
United Electric Controls
5829 Grazing Court
Mason, OH 45040
Phone: 513-535-5486
email: midatlanticsales@ueonline.com
United Electric Controls
102 Salazar Court
Clayton, CA 94517
Phone: 925-408-5997
email: westcoastsales@ueonline.com
United Electric Controls
27 Summit Terrace
Sparta, NJ 07871
Phone: 973-271-2550
email: easternsales@ueonline.com
United Electric Controls
33018 Weatherby Court
Fulshear, Texas 77441
Phone: 832-457-6138
email: southwestsales@ueonline.com
CANADA
68 Mosley Crescent
Brampton, Ontario
Canada L6Y 5C8
Phone: 905-455-5131
FAX: 905-455-5131
180 Dexter Avenue, P.O. Box 9143
Watertown, MA 02471-9143 USA
Telephone: 617 926-1000 Fax: 617 926-2568
www.ueonline.com
U N I T E D E L E C T R I C
C O N T R O L S
CP05125000
RECOMMENDED PRACTICES AND WARNINGS
United Electric Controls Company recommends careful consideration
of the following factors when specifying and installing UE pressure
and temperature units. Before installing a unit, the Installation
and Maintenance instructions provided with unit must be read and
understood.
• To avoid damaging unit, proof pressure and maximum temperature
limits stated in literature and on nameplates must never be
exceeded, even by surges in the system. Operation of the unit up to
maximum pressure or temperature is acceptable on a limited basis
(e.g., start-up, testing) but continuous operation must be restricted
to the designated adjustable range. Excessive cycling at maximum
pressure or temperature limits could reduce sensor life.
• A back-up unit is necessary for applications where damage to
a primary unit could endanger life, limb or property. A high or
low limit switch is necessary for applications where a dangerous
runaway condition could result.
• The adjustable range must be selected so that incorrect,
inadvertent or malicious setting at any range point cannot result
in an unsafe system condition.
• Install unit where shock, vibration and ambient temperature
fluctuations will not damage unit or affect operation. When
applicable, orient unit so that moisture does not enter the
enclosure via the electrical connection. When appropriate, this
entry point should be sealed to prevent moisture entry.
• Unit must not be altered or modified after shipment. Consult UE
if modification is necessary.
• Monitor operation to observe warning signs of possible damage
to unit, such as drift in set point or faulty display. Check unit
immediately.
• Preventative maintenance and periodic testing is necessary for
critical applications where damage could endanger property or
personnel.
• Electrical ratings stated in literature and on nameplate must not
be exceeded. Overload on a switch can cause damage, even on
the first cycle. Wire unit according to local and national electrical
codes, using wire size recommended in installation sheet.
• Do not mount unit in ambient temp. exceeding published limits.
LIMITED WARRANTY
Seller warrants that the product hereby purchased is, upon delivery,
free from defects in material and workmanship and that any such
product which is found to be defective in such workmanship or
material will be repaired or replaced by Seller (Ex-works, Factory,
Watertown, Massachusetts. INCOTERMS); provided, however, that this
warranty applies only to equipment found to be so defective within
a period of 36 months from the date of manufacture by the Seller.
Seller shall not be obligated under this warranty for alleged defects
which examination discloses are due to tampering, misuse, neglect,
improper storage, and in any case where products are disassembled
by anyone other than authorized Seller’s representatives. EXCEPT FOR
THE LIMITED WARRANTY OF REPAIR AND REPLACEMENT STATED
ABOVE, SELLER DISCLAIMS ALL WARRANTIES WHATSOEVER WITH
RESPECT TO THE PRODUCT, INCLUDING ALL IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Limitation OF Seller’s Liability
Seller’s liability to Buyer for any loss or claim, including
liability incurred in connection with (i) breach of any
warranty whatsoever, expressed or implied, (ii) a breach of
contract, (iii) a negligent act or acts (or negligent failure
to act) committed by Seller, or (iv) an act for which strict
liability will be inputted to seller, is limited to the “limited
warranty” of repair and/or replacement as so stated in our
warranty of product. In no event shall the Seller be liable
for any special, indirect, consequential or other damages
of a like general nature, including, without limitation,
loss of profits or production, or loss or expenses of any
nature incurred by the buyer or any third party.
UE specifications subject to change without notice.
International Offices
CHINA
United Electric Controls, Shanghai Office
Room 1011, 10th Flr,
Huai Hai Zhonghua Building
No. 885, Renmin Road, Luwan District
Shanghai 200010, P.R. China
Phone: +8621-6255 8059
email: chinasales@ueonline.com
United Electric Controls, Beijing Office
Room 1006, Jainhao International Bldg.
Block D, No. 116
Zizhuyuanlu, Haidian District
Beijing, China 100089
Phone & Fax: +86-10-5893-0551
email: beijingsales@ueonline.com
EUROPE
United Electric Controls
05-806 Komorow
Kujawska 5, Poland
Phone: +48 22 499 4804
email: easterneuropesales@ueonline.com
INDIA
United Electric
#402, Aries Avenue - 1
United Colony, Sama, Baroda
Baroda (Gujarat), India
Phone: +91 (-265) -2788654
email: indiasales@ueonline.com
ASIA-PACIFIC
United Electric Controls, Far East
No. 1-2-2, 2nd Floor
Jalan 4/101C
Cheras Business Centre
56100 Kuala Lumpur, Malaysia
Phone: 603-9133-4122
email: asiapacific@ueonline.com
RUSSIA & SCANDINAVIA
United Electric Controls, Moscow
Elninskaya str., 15-140
Moscow, 121552 Russia
Phone: +7 (495) 792-88-06
email: russiansales@ueonline.com
Be sure to visit www.ueonline.com for the latest information regarding the One Series.16