Liquisys M CPM223/253. pH/ORP Measurement. Transmitter for analog and digital glass and ISFET sensors. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
The 212 Heat Calculator is designed to measure the energy consumed in hot water heating systems and chilled water
cooling systems. The 212 will interface with a wide range
of flowmeters, including vortex and magnetic flowmeters with pulse outputs, positive displacement and inferential water meters, turbine and paddle wheel flowmeters.
The 212 Heat Calculator is designed to measure the energy consumed in hot water heating systems and chilled water
cooling systems. The 212 will interface with a wide range
of flowmeters, including vortex and magnetic flowmeters with pulse outputs, positive displacement and inferential water meters, turbine and paddle wheel flowmeters.
Data Acquisition Equipment for Automation and Process ControlMiller Energy, Inc.
Power generation, process automation, and factory automation in manufacturing industries require rigorous, continuous monitoring in the control room. Yokogawa's DX series recorders are purpose-built data acquisition systems designed for industrial automation.
Siemens Terminal Box Controller (APOGEE Automation System )CONTROLS & SYSTEMS
In This PPT we are discussed about complete details of that product (Use,Operation, Technical details, Dimensions, Wiring, and etc..)
Please Support us and Follow our other Sites
https://www.instagram.com/controlsandsystems.offical
https://twitter.com/ControlsSystems
https://automationtechplc2.blogspot.com
https://humidificationcontrol.blogspot.com
https://controlsandsystems.business.site
www.controls.systemsdm@gmail.com
If you enjoyed this article, share it with your friends and colleagues
Toshniwal - Thermal mass flow meters and controllerSangeethaS99
THERMAL MASS FLOW METERS AND CONTROLLER
The range of Thermal Mass Flow Meters from Bronkhorst address high accuracy in low flow rate scenarios like those seen in laboratory and Pilot plant usages. With a housing designed for laboratory and clean processing conditions, the instruments are truly unique in their capability to measure and control flow ranges between 0,014…0,7 mln/min and 8…1670 ln/min with pressure rating between vacuum and 400 bar – all in one range of instruments.
FEATURES
Rangeability in digital mode up to 1:150
High accuracy (standard 0,5% Rd plus 0,1% FS)
Pressure ratings 64 / 100 bar
Highly resistant to mechanical shocks and pressure fluctuations
Large range of Input/output options to choose from
Extremely fast and dynamic response
User configurable control characteristics
Applications
Analytical/environmental equipment
Gas flow monitoring in food, chemical and petrochemical industries
Gas consumption measurement in gas distribution systems for internal accounting purposes
Detection of gas leakage through objects
Semiconductor manufacturing
Surface treatment installations
GE Advanced Modular Calibrator for Process Measurement InstrumentsFlow-Tech, Inc.
The DPI 620 Genii is an easy to use, rugged, and highly accurate multifunction instrument for calibrating & maintaining process instrumentation. Its modular design and functionality means it can be expanded over time and tailored to applications as needs change. With options that include HART / Fieldbus / Profibus communications, it’s a powerful, simple to use and high accuracy calibrator.
Series One Safety Transmitter, Pressure and Temperature SwitchIves Equipment
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
Thermal dispersion mass flow transmitters measure mass flow by detecting heat dissipation from a heated surface. The sensor contains two mass balanced elements with precision matched RTDs. The reference sensor measures the process temperature (up to +400° F [+200° C]); the second RTD measures the temperature of the heated sensor. The power to the heater is varied to maintain a constant temperature difference above the reference temperature.
There is an inherent non-linear relationship between power and mass flow. A microprocessor compares the power against the calibration curve and converts the power requirements to the mass flow rate. Temperature is also measured to provide temperature compensation of the mass flow over the operating range of the instrument.
Untuk informasi lebih lanjut, demo request dan pemesanan produk, dapat menghubungi kami di Siwali Jakarta : 021-45850618 / Siwali Surabaya : 031-8421278.
Data Acquisition Equipment for Automation and Process ControlMiller Energy, Inc.
Power generation, process automation, and factory automation in manufacturing industries require rigorous, continuous monitoring in the control room. Yokogawa's DX series recorders are purpose-built data acquisition systems designed for industrial automation.
Siemens Terminal Box Controller (APOGEE Automation System )CONTROLS & SYSTEMS
In This PPT we are discussed about complete details of that product (Use,Operation, Technical details, Dimensions, Wiring, and etc..)
Please Support us and Follow our other Sites
https://www.instagram.com/controlsandsystems.offical
https://twitter.com/ControlsSystems
https://automationtechplc2.blogspot.com
https://humidificationcontrol.blogspot.com
https://controlsandsystems.business.site
www.controls.systemsdm@gmail.com
If you enjoyed this article, share it with your friends and colleagues
Toshniwal - Thermal mass flow meters and controllerSangeethaS99
THERMAL MASS FLOW METERS AND CONTROLLER
The range of Thermal Mass Flow Meters from Bronkhorst address high accuracy in low flow rate scenarios like those seen in laboratory and Pilot plant usages. With a housing designed for laboratory and clean processing conditions, the instruments are truly unique in their capability to measure and control flow ranges between 0,014…0,7 mln/min and 8…1670 ln/min with pressure rating between vacuum and 400 bar – all in one range of instruments.
FEATURES
Rangeability in digital mode up to 1:150
High accuracy (standard 0,5% Rd plus 0,1% FS)
Pressure ratings 64 / 100 bar
Highly resistant to mechanical shocks and pressure fluctuations
Large range of Input/output options to choose from
Extremely fast and dynamic response
User configurable control characteristics
Applications
Analytical/environmental equipment
Gas flow monitoring in food, chemical and petrochemical industries
Gas consumption measurement in gas distribution systems for internal accounting purposes
Detection of gas leakage through objects
Semiconductor manufacturing
Surface treatment installations
GE Advanced Modular Calibrator for Process Measurement InstrumentsFlow-Tech, Inc.
The DPI 620 Genii is an easy to use, rugged, and highly accurate multifunction instrument for calibrating & maintaining process instrumentation. Its modular design and functionality means it can be expanded over time and tailored to applications as needs change. With options that include HART / Fieldbus / Profibus communications, it’s a powerful, simple to use and high accuracy calibrator.
Series One Safety Transmitter, Pressure and Temperature SwitchIves Equipment
The One Series Safety Transmitter is a transmitter-switch for monitoring pressure or temperature and meets the requirements of SIL 2 for random integrity at HFT = 0, SIL 3 for random integrity at HFT = 1 and SIL 3 for systematic capability. The One Series Safety Transmitter incorporates UE’s patented IAW self diagnostics, redundant and diverse signal processing and software algorithms to detect abnormalities in the process and internal faults. The design is based on a powerful microprocessor that provides an extremely fast response time for emergency shutdown situations.
Thermal dispersion mass flow transmitters measure mass flow by detecting heat dissipation from a heated surface. The sensor contains two mass balanced elements with precision matched RTDs. The reference sensor measures the process temperature (up to +400° F [+200° C]); the second RTD measures the temperature of the heated sensor. The power to the heater is varied to maintain a constant temperature difference above the reference temperature.
There is an inherent non-linear relationship between power and mass flow. A microprocessor compares the power against the calibration curve and converts the power requirements to the mass flow rate. Temperature is also measured to provide temperature compensation of the mass flow over the operating range of the instrument.
Untuk informasi lebih lanjut, demo request dan pemesanan produk, dapat menghubungi kami di Siwali Jakarta : 021-45850618 / Siwali Surabaya : 031-8421278.
EL-FLOW Prestige is the next generation of Bronkhorst Mass Flow Meters / Controllers for gases. Nearly all core components have been redesigned and many improvements and innovations have been incorporated. With this new series Bronkhorst introduced the “Differential Temperature Balancing” technology, ensuring a superb sensor stability.
Data Teknis Gossen Metrawatt Installation Tester : PROFITEST PRIME | PRIME ACPT. Siwali Swantika
Pemesanan produk, hubungi PT Siwali Swantika melalui WhatsApp, Jakarta : 0811-1519-949 (chat only) | Surabaya : 0811-1519-948 (chat only). Kunjungi website kami di www.siwali.com, untuk detail informasi spesifikasi dan model alat.
EL300 multi channel water controller-tethys datasheetENVIMART
EL300 multi channel water controller-tethys datasheet - Tethys - Envimart JSC - www.envimart.vn - ĐT: 028 77727979 - sales@envimart.vn - Nền tảng cung cấp thiết bị, vật tư ngành nước và môi trường.
With an installed base approaching 4 million nodes IO-Link is THE protocol for communication down to the sensor and actuator level. This presentation will be covering what a typical IO-Link solution consists of, how it interfaces to the control system and the benefits that can be derived from this increased level of communication with IO-Link devices. These include: easier handling of measurement signals, remote and automatic device parameterisation, smart sensor diagnostic functions, safety over IO-Link whilst also being an enabler for Industrial IoT and Industry 4.0 strategies.
D List 835-SEC-15-Sensor-Control-Unit-d-listcontroller-technical-dataHans Bronkhorst
Technical data Sensor Control Unit 835. the new List controller for the SEC sensor cable of Listec GMBH. SenseTek is the specialist with the most experience from the late 90`s. Contact us for the right solutions.
As a distributor for Fire Security we are happy to help you. call +31(0)20 6131611
NIVELCO EasyTREK SP-500 Ultrasonic Level Transmitters for LiquidsArjay Automation
The newest generation EasyTREK SP-500 series level transmitters are based on NIVELCO’s 35 years of experience with ultrasonic level measurement. The IP68 rated units have their transducer and processing electronics incorporated in one single housing. The new EasyTREK transmitters utilize HART® 7 communication so they can be used in multidrop systems connected to MultiCONT process controller/display, or to a PC with the help of the UNICOMM HART®-USB modem or similar. The transmitters can be remotely programmed also with Handheld Field Communicator, and can be connected wirelessly to a PC with the SAT-504 Bluetooth® HART® modem.
Data Teknis Gossen Metrawatt Special Multimeter : METRAHIT PM TECH, METRAHIT PM XTRA, METRAHIT EBASE, METRAHIT ETECH, METRAHIT EXTRA, METRAHIT ESPECIAL, METRAHIT EU PRO
Pemesanan produk, hubungi PT Siwali Swantika melalui WhatsApp, Jakarta : 0811-1519-949 (chat only) | Surabaya : 0811-1519-948 (chat only). Kunjungi website kami di www.siwali.com, untuk detail informasi spesifikasi dan model alat.
The density measuring line can be used in liquid media. Density computer for liquids. Also for use in hazardous areas. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
The universal paddle level limit switch FTE 30 is used as a full, empty and demand alarm on silos containing solids. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
Liquipoint T FTW31, FTW32 is point level switch for multiple point detection in conductive liquids. Email: lam.nguyen@vietan-enviro.com HP: 0945 293292
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Connector Corner: Automate dynamic content and events by pushing a buttonDianaGray10
Here is something new! In our next Connector Corner webinar, we will demonstrate how you can use a single workflow to:
Create a campaign using Mailchimp with merge tags/fields
Send an interactive Slack channel message (using buttons)
Have the message received by managers and peers along with a test email for review
But there’s more:
In a second workflow supporting the same use case, you’ll see:
Your campaign sent to target colleagues for approval
If the “Approve” button is clicked, a Jira/Zendesk ticket is created for the marketing design team
But—if the “Reject” button is pushed, colleagues will be alerted via Slack message
Join us to learn more about this new, human-in-the-loop capability, brought to you by Integration Service connectors.
And...
Speakers:
Akshay Agnihotri, Product Manager
Charlie Greenberg, Host
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Accelerate your Kubernetes clusters with Varnish CachingThijs Feryn
A presentation about the usage and availability of Varnish on Kubernetes. This talk explores the capabilities of Varnish caching and shows how to use the Varnish Helm chart to deploy it to Kubernetes.
This presentation was delivered at K8SUG Singapore. See https://feryn.eu/presentations/accelerate-your-kubernetes-clusters-with-varnish-caching-k8sug-singapore-28-2024 for more details.
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
Generating a custom Ruby SDK for your web service or Rails API using Smithyg2nightmarescribd
Have you ever wanted a Ruby client API to communicate with your web service? Smithy is a protocol-agnostic language for defining services and SDKs. Smithy Ruby is an implementation of Smithy that generates a Ruby SDK using a Smithy model. In this talk, we will explore Smithy and Smithy Ruby to learn how to generate custom feature-rich SDKs that can communicate with any web service, such as a Rails JSON API.
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
The Art of the Pitch: WordPress Relationships and Sales
pH.ORP Transmitter-Analog and digital glass
1. TI194C/07/EN/13.11
71130248
Technical Information
Liquisys M CPM223/253
pH/ORP Measurement
Transmitter for analog and digital glass and ISFET sensors
The modular design of the Liquisys M CPM223/253 allows easy
adaption of the transmitter to a variety of customer
requirements. Starting with the basic version for "measurement
and alarm generation", the transmitter can be equipped with
additional software and hardware modules for special
applications. These modules can also be retrofitted as required.
Application
• Effluent treatment
• Neutralization
• Detoxication (electroplating)
• Water treatment
• Water monitoring
Your benefits
• Memosens technology
• Field or panel-mounted housing
• Universal application
• Simple handling
– Logically arranged menu structure
– Large two-line display
– Ultrasimple two-point calibration
• Safe operation
– Overvoltage (lightning) protection
– Direct access for manual contact control
– Calibration plausibility check
– User-defined alarm configuration
The basic unit can be extended with:
• Addtional 2 or 4 contacts for use as:
– Limit contacts (also for temperature)
– P(ID) controller
– Timer for simple rinse processes
– Complete cleaning with Chemoclean
– Current input
• Plus package:
– User defined current output characteristics
– Automatic cleaning trigger on alarm or limit violation
– Sensor Check System for pH glass and reference
– Live check of sensor
– Special neutralization controller
• HART or PROFIBUS-PA/-DP
• 2nd current output for temperature, pH/ORP or continuous
controller
2. Liquisys M CPM223/253
2 Endress+Hauser
Function and system design
Features of the basic version pH and ORP value measurement
This is selected via the menu. During measurement, the value measured can be displayed in the other
measuring mode (e.g. pH - mV or ORP % - ORP mV). The temperature is displayed at the same time or, if
desired, not shown at all.
Calibration
pH electrodes are normally calibrated with the same pH values. Therefore the transmitter presents the settings
from the previous calibration as defaults for the next calibration. If the buffer solutions are interchanged by
accident (e.g. pH 4 buffer first, then pH 7 buffer instead of pH 7 first and then pH 4) the plausibility check
ensures that the calibration is accepted anyway.
Configuration
Different alarms are required depending on application and operator. Therefore the transmitter permits
independent configuration of the alarm contact and error current for each individual error. Unnecessary
or undesirable alarms can be suppressed in this manner. Up to four contacts can be used as limit contacts
(also for temperature) to implement a P(ID) controller or for cleaning functions.
Direct manual operation of the contacts (bypassing the menu) provides quick access to limit, control or
cleaning contacts, permitting speedy correction of deviations.
Additional functions of the
plus package
Current output
In order to output wide measuring ranges while still achieving a high resolution in specific ranges, the current
output can be configured as required via a table. This permits bilinear or quasi-logarithmic curves, etc.
Sensor-Check-System (SCS)
The sensor check system alerts to deviations of the pH glass impedance or reference impedance (analog sensors
only) from the normal range, thus indicating possible failure due to pH electrode blocking or damage.
In addition, the SCS detects glass breakage of glass electrodes and leakages of ISFET sensors.
Live-check
The live check issues an alarm when the sensor signal does not change over a defined period of time. This may
be caused by blocking, passivation, separation from the process, etc.
Neutralization controller
A special control response that cannot be handled adequately by a P(ID) controller is required to neutralize
solutions. For this reason, the transmitter provides a special neutralization controller function by combining
two P(ID) controllers.
Current input
The current input of the transmitter allows two different applications: controller shut-down in case of lower
flow rate violation or total failure in the main flow as well as feedforward control. Both functions are also
combinable.
3. Liquisys M CPM223/253
Endress+Hauser 3
Measuring system A complete measuring systems comprises:
• The transmitter Liquisys M CPM223 or CPM253
• A pH/ORP electrode with or without an integrated temperature sensor
• An immersible, flow or retractable assembly
• A measuring cable(e.g. CPK9)
Options: extension cable, junction box VBA or VBM
a0007781
Complete measuring system Liquisys M CPM223/253
1
2
3
4
5
Flow assembly CPA250
Junction box VBA
Liquisys M CPM253
Measuring cable e.g. CPK9
Liquisys M CPM223
6
7
8
9
Retractable assembly Cleanfit W CPA450
Electrode, e.g Orbisint CPS11
Immersion assembly CPA111
Extension cable
CAL REL
REL1
REL1
ALARM
REL2
REL2E
CAL REL
REL1
REL1
ALARM
REL2
REL2E
1 2 3
4
56
7
8
4
9
4. Liquisys M CPM223/253
4 Endress+Hauser
Input
Measured variables pH (analog or digital sensors)
ORP
Temperature
Measuring range
Input resistance > 1012
Ω (for nominal operating conditions) for standard sensors
Cable specification
Binary inputs
Current input 4 to 20 mA, galvanically separated
Load: 260 Ω at 20 mA (voltage drop 5.2 V)
Output
Output signal 0/4 to 20 mA, galvanically separated, active
Signal on alarm 2.4 or 22 mA
Load maximum 500 Ω
pH: –2 to 16
ORP: –1500 to +1500 mV / 0 to 100 %
Temperature:
Pt 100 -50 to +150 °C (-58 to +302 °F)
Pt 1000 (versions IS / PS) -50 to +150 °C (-58 to +302 °F)
NTC 30K (versions IS / PS) -20 to +100 °C (-4 to +212 °F)
Length of cable (analog): max. 50 m (164 ft)
Length of cable (digital): max. 100 m (328 ft)
Voltage: 10 to 50 V
Power consumption: max. 10 mA
HART
Signal coding Frequency Shift Keying (FSK) + 0.5 mA via current output signal
Data transfer rate 1200 Baud
Galvanic isolation yes
PROFIBUS PA
Signal coding Manchester Bus Powered (MBP)
Data transfer rate 31.25 kBit/s, voltage mode
Galvanic isolation yes (IO-Module)
PROFIBUS DP
Signal coding RS485
Data transfer rate 9.6 kBd, 19.2 kBd, 93.75 kBd, 187.5 kBd, 500 kBd, 1.5 MBd
Galvanic isolation yes (IO-Module)
5. Liquisys M CPM223/253
Endress+Hauser 5
Output range
Resolution max. 700 digits/mA
Min. distance for
0 / 4 to 20 mA signal
10% of measuring range
Isolation voltage max. 350 VRMS/500 V DC
Overvoltage protection according to EN 61000-4-5
Auxiliary voltage output
Contact outputs
Limit contactor
Controller
Alarm
pH: adjustable, min. Δ 1 pH
ORP:
absolute: adjustable, min. Δ 50 mV
relative: fixed, 0 to 100 %
Temperature: adjustable, Δ 10 to Δ 100 % of upper range value
Output voltage: 15 V ± 0.6
Output current: max. 10 mA
Switching current with ohmic load (cos ϕ = 1): max. 2 A
Switching current with inductive load (cos ϕ = 0.4): max. 2 A
Switching voltage: max. 250 V AC, 30 V DC
Switching power with ohmic load (cos ϕ = 1): max. 500 VA AC, 60 W DC
Switching power with inductive load (cos ϕ = 0.4): max. 500 VA AC, 60 W DC
Pickup/dropout delay: 0 to 2000 s
Function (adjustable): pulse length/pulse frequency controller
Controller response: PID
Control gain Kp: 0.01 to 20.00
Integral action time Tn: 0.0 to 999.9 min
Derivative action time Tv: 0.0 to 999.9 min
Period for pulse length controller: 0.5 to 999.9 s
Frequency for pulse frequency controller: 60 to 180 min-1
Basic load: 0 to 40% of max. set value
Function (selectable): latching / momentary contact
Alarm threshold adjustment range: pH / temperature: complete measuring range
Alarm delay: 0 to 2000 s
0 to 2000 min
6. Liquisys M CPM223/253
6 Endress+Hauser
Protocol specific data HART
Manufacturer ID 11h
Device type code 0091h
Transmitter specific revision 0001h
HART specification 5.0
DD files www.products.endress.com/profibus
Load HART 250 Ω
Device variables None (dynamic variables PV, SV, only)
Features supported -
PROFIBUS PA
Manufacturer ID 11h
Ident number 1516h
Device revision 11h
Profile version 2.0
GSD files www.products.endress.com/profibus
GSD file version
Output values Main value, temperature value
Input values Display value of PLC
Features supported Device locking: The device can be locked by hardware or software.
PROFIBUS DP
Manufacturer ID 11h
Ident number 1520h
Profile version 2.0
GSD files www.products.endress.com/profibus
GSD file version
Output values Main value, temperature value
Input values Display value of PLC
Features supported Device locking: The device can be locked by hardware or software.
7. Liquisys M CPM223/253
Endress+Hauser 7
Power supply
Electrical connection of analog
sensors
a0007753
Electrical connection Liquisysy M
A
B
C
D
E
F
G
H
I
Standard sensor
ISFET sensor
Outer screen connection for glass electrodes
Potential matching
Temperature sensor
Signal output 1 pH/ORP
Signal output 2 temperature, pH/ORP or controller
Binary input 1 (Hold)
Binary input 2 (Chemoclean)
J
K
L
M
N
O
P
Q
Auxiliary voltage output
Alarm (contact position currentless)
Relay 1 (contact position currentless)
Relay 2 (contact position currentless)
Relay 3 (contact position currentless)
Relay 4 (contact position currentless)
Current input 4 to 20 mA
Power supply
pH
Ref.
11
12
13
47
48
49
57
58
59
51
52
53
54
55
56
PA/
PM
15 V
85
86
S
10-50 V
81
93
82
94
10-50 V
L+
L-
L1
N
23 +
24 -
mA
~ =
41
42
43
pH
mA31
32
mA
33
34
A
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
SRC
DRN.
B
8. Liquisys M CPM223/253
8 Endress+Hauser
Electrical connection of
Memosens sensors
a0007754
Transmitter electrical connection with Memosens technology
A
B
C
D
E
F
G
Screen
Sensor
Signal output 1 pH/redox
Signal output 2 temperature, pH/redox or controller
Binary input 1 (Hold)
Binary input 2 (Chemoclean)
Auxiliary voltage output
H
I
J
K
L
M
N
Alarm (contact position currentless)
Relay 1 (contact position currentless)
Relay 2 (contact position currentless)
Relay 3 (contact position currentless)
Relay 4 (contact position currentless)
Current input 4 to 20 mA
Power supply
87
88
96
47
48
49
57
58
59
51
52
53
54
55
56
15 V
85
86
10-50 V
81
93
82
94
10-50 V
L+
L-
L1
N
23 +
24 -
mA
~ =
41
42
43
pH
mA31
32
mA
33
34
A
B
C
D
E
F
G
H
J
K
L
M
N
S
97
IA
B
BN
WH
GN
YE
9. Liquisys M CPM223/253
Endress+Hauser 9
Sensor cable The pH and ORP electrodes are connected using special terminated and shielded multicore cables. The
measuring cable can be extended with a junction box and an extension cable.
Termination instructions are supplied with the measuring cable.
a0007765
Connection CPS11 with CPK9 and CPS471 with CPK12 to Liquisys M
A Panel-mounted instrument
B Field instrument
C Potential matching PM for symmetrical connection
a0007766
Unsymmetrical and symmetrical connection of ORP electrodes to Liquisys M
A Panel-mounted instrument
B Field instrument
C Potential matching PM for symmetrical connection
J
S S
DRN
PA/
PM
PA/
PM
CPK9 CPK12
CPS11 CPS471
B
C C
B
S
GN WH YE BN
Schirm/
Screen
11 12 13 11 12 13
BN BN
BNC BKBKBKinnen /
internal
innen /
internal
SRC RefSRC RefRef
pH/
Redox
GN WH YE RD BN
PE
PE
A A
)
S SNC
PA/
PM
PA/
PMNC
CPK1
BN BNC BK BN BNC BK
CPK1
BB AA
CPS12 CPS12
Schirm/
Screen
Schirm/
screen
RefRef
C
BN BN
10. Liquisys M CPM223/253
10 Endress+Hauser
a0007773
Connection of digital sensor CPS11D with CYK10
Supply voltage Depending on ordered version:
100/115/230 V AC +10/-15 %, 48 to 62 Hz
24 V AC/DC +20/-15 %
Fieldbus connection
Power consumption max. 7.5 VA
Mains protection Fine-wire fuse, medium-slow blow 250 V/3.15 A
S
CYK10
CPS11D
BN WH GN YE
87 88 96 97
HART
Supply voltage n/a, active current outputs
Integrated reverse voltage protection n/a, active current outputs
PROFIBUS PA
Supply voltage 9 V to 32 V, max. 35 V
Polarity sensitive no
FISCO/FNICO compliant acc. to IEC 60079-27 no
PROFIBUS DP
Supply voltage 9 V to 32 V, max. 35 V
Polarity sensitive n/a
FISCO/FNICO compliant acc. to IEC 60079-27 no
11. Liquisys M CPM223/253
Endress+Hauser 11
Performance characteristics
Reference temperature 25 °C (77 °F)
Resolution
Maximum measured error1)
Repeatability1)
Zero point
Slope
Offset
pH: 0.01 pH
ORP: 1 mV/0.1 %
Temperature: 0.1 °C
1) acc. to IEC 746-1, for nominal operating conditions
Display
pH: max. 0.5 % of measuring range
ORP: max. 0.5 % of measuring range
Temperature: max. 1.0 % of measuring range
Signal output
pH: max. 0.75 % of measuring range
ORP: max. 0.75 % of measuring range
Temperature: max. 1.25 % of measuring range
pH: max. 0.2 % of measuring range
ORP: max. 0.2 % of measuring range
Glass: pH 5.0 to 9.0 (nominal pH 7.00)
Antimon: pH –1.0 to 3.0 (nominal pH 1.00)
ISFET: -500 to +500 mV
Glass: 38.00 to 65.00 mV/pH (nominal 59.16 mV/pH)
Antimon: 25.00 to 65.00 mV/pH (nominal 59.16 mV/pH)
ISFET: 38.00 to 65.00 mV/pH (nominal 59.16 mV/pH)
pH: ±2 pH
ORP: ±120 mV/±50 %
Temperature: ±5 °C
12. Liquisys M CPM223/253
12 Endress+Hauser
Installation
Installation instructions
a0005733
Field instrument
a0005737
Mounting on pipes
1 - 3 Mounting screws and mounting plate
CAL REL
REL1
REL1
ALARM
REL2
REL2E
Pg 7
Pg 16
M5
11/
0.43
Ø6/
Ø0.24
115 / 4.53
157/6.18
247/9.72
70/2.76
70 / 2.76
154 / 6.06
170 / 6.69
mm / inch
Pg 13.5
1
2
3
1
1
3
Ømax.60/
2.36
mm / inch
13. Liquisys M CPM223/253
Endress+Hauser 13
a0005734
View into the field instrument
1
2
3
4
Removable electronics box
Partition plate
Terminal blocks
Fuse
a0005736
Wall mounting of the field instrument
1 Mounting holes
2 Protecting cap
a0005738
Mounting of the field instrument with mounting post and weather protection cover
1 - 3 Mounting holes
1
2
3
4
1
2
154 / 6.06
mm / inch
Ø6/
Ø0.24
3
1
2
3
14. Liquisys M CPM223/253
14 Endress+Hauser
a0005735
Dimensions panel-mounted instrument
a0005739
Installation of the panel-mounted instrument
1 Wall of control cabinet
2 Gasket
3 Tensioning screws
* Required installation depth
90 / 3.54
139/5.47
96/3.78
6 /
0.24
mm / inch
92 / 3.62
149.5/5.89
1
2
3
3
3
92 / 3.62+0.5 +0.02
92/3.62
+0.5+0.02
90/3.54
57/2.24
33/
1.30
approx. 25 /
0.98
139 / 5.47
max. 45 /
1.77 6 /
0.24
96/3.78
92/
3.62
approx. 165 / 6.50*
mm / inch
15. Liquisys M CPM223/253
Endress+Hauser 15
Environment
Ambient temperature -10 to +55 °C (+14 to +131 °F)
Storage temperature –25 to +65 °C (-13 to +149 °F)
Electromagnetic compatibility Interference emission and interference immunity as per EN 61326-1:2006, EN 61326-2-3:2006
Ingress protection
Electrical safety according EN/IEC 61010-1:2001, Installation Category II, for use up to 2000 m above sea level
CSA Apparatus with CSA General Purpose Approval are certified for indoor use.
Relative humidity 10 to 95%, non-condensing
Pollution degree The product is suitable for pollution degree 2.
Mechanical construction
Dimensions
Weight
Materials
Terminals
Panel mounted instrument: IP 54 (front), IP 30 (housing)
Field instrument: IP 65 / tightness acc. to NEMA 4X
Panel mounted instrument: 96 x 96 x 145 mm (3.78 x 3.78 x 5.71 inches)
Mounting depth: approx. 165 mm (6.50")
Field instrument: 247 x 170 x 115 mm (9.72 x 6.69 x 4.53 inches)
Panel mounted instrument: max. 0.7 kg (1.5 lb)
Field instrument: max. 2.3 kg (5.1 lb)
Housing of panel mounted instrument: Polycarbonate
Field housing: ABS PC FR
Front membrane: Polyester, UV-resistant
Cross section 2.5 mm2
(14 AWG)
16. Liquisys M CPM223/253
16 Endress+Hauser
Operability
Operating concept All instrument control functions are arranged in a logical menu structure. Following access code entry, the
individual parameters can be easily selected and modified as needed.
Display elements
a0007771-en
Operating elements
1 LC display for display of measured values, configuration data and current menu field
2 Field for user labeling
3 4 main control keys for calibration and instrument configuration
4 Key for switching between automatic/manual operation
5 LED indicators for switched limit outputs
6 LED indicator for alarm function
7 Display of active contact and key for relay switching in manual mode
The display simultaneously shows the current measured value and the temperature - the essential process data.
Brief information texts in the configuration menu provide assistance with parameter configuration.
Certificates and approvals
4 symbol Declaration of conformity
The product meets the requirements of the harmonized European standards. It thus complies with the legal
requirements of the EC directives.
The manufacturer confirms successful testing of the product by affixing the 4 symbol.
Ex approval for zone 2 Application of transmitter as related electrical equipment in non-hazardous area or in simple pressurized
apparatus; application of sensor in hazardous area zone 2
CSA general purpose C.M2.3-..2...
C.M2.3-..3...
C.M2.3-..7...
7.05
pH
R262
1
2
3
4
5
6
7
Setpoint
C.M2.3-..4...
C.M223-..6...
C.M253-..A...
ATEX II (3)G (Ex nL) IIC
17. Liquisys M CPM223/253
Endress+Hauser 17
Ordering information
Product structure
Additional functions of the
Plus package
• Current output table to cover large areas with varying resolution
• Monitoring of sensor and process for safe operation
• Neutralization controller to keep pH value constant by dosing acid and alkali
• Automatic cleaning function start2)
Sensor input, software
IS pH (glass/ISFET) / ORP; Plus package
MR pH (digital sensor); pH (glass/ISFET)/ORP; basic version
MS pH (digital sensor); pH (glass/ISFET)/ORP; Plus package
PR pH (glass)/ORP; basic version
PS pH (glass)/ORP; Plus package
Power supply, approval
A 24 V AC/DC; ATEX II (3)G (Ex nL) IIC (CPM253 only)
0 230 V AC
1 115 V AC
2 230 V AC; CSA Gen. Purp.
3 115 V AC; CSA Gen. Purp.
4 230 V AC; ATEX II (3)G [Ex nL] IIC
5 100 V AC
6 24 V AC/DC; ATEX II (3)G [Ex nL] IIC (CPM223 only)
7 24 V AC; CSA Gen. Purp.
8 24 V AC/DC
Output
0 1 x 20 mA, primary value
1 2 x 20 mA, primary value + secondary value
3 PROFIBUS PA
4 PROFIBUS DP
5 1 x 20 mA, primary value, HART
6 2 x 20 mA, primary value, HART + secondary value
Additional contacts
05 not selected
10 2 relays (limit/P(ID)/timer)
15 4 relays (limit/P(ID)/Chemoclean) (not with PROFIBUS DP)
16 4 relays (limit/P(ID)/timer) (not with PROFIBUS DP)
20 1 x 4 ... 20 mA input + 2 relays (limit/P(ID)/timer)
25 1 x 4 ... 20 mA input + 4 relays (limit/P(ID)/Chemoclean) (not with PROFIBUS DP)
26 1 x 4 ... 20 mA input + 4 relays (limit/P(ID)/timer) (not with PROFIBUS DP)
Additional features (CPM223 only)
PRL Protective layer
Marking
1 Tagging (Tag), see additional spec.
CPM253-
complete order code
CPM223-
2) In combination with "Additional contacts" only, see product structure
18. Liquisys M CPM223/253
18 Endress+Hauser
Scope of delivery The delivery of the field instrument includes:
• 1 transmitter CPM253
• 1 plug-in screw terminal
• 1 cable gland Pg 7
• 1 cable gland Pg 16 reduced
• 2 cable glands Pg 13.5
• 1 Operating Instructions BA194C/07/EN
• versions with HART communication:
1 Operating Instructions Field Communication with HART, BA208C/07/EN
• versions with PROFIBUS communication:
1 Operating Instructions Field Communication with PROFIBUS PA/DP, BA209C/07/EN
• versions with explosion protection for hazardous area zone II (ATEX II 3G):
Safety Instructions for use in explosion-hazardous areas, XA194C/07/A3
The delivery of the panel mounted instrument includes:
• 1 transmitter CPM223
• 1 set of plug-in screw terminals
• 2 tensioning screws
• 1 BNC-plug (solder-free)
• 1 Operating Instructions BA194C/07/EN
• versions with HART communication:
1 Operating Instructions Field Communication with HART, BA208C/07/EN
• versions with PROFIBUS communication:
1 Operating Instructions Field Communication with PROFIBUS PA/DP, BA209C/07/EN
• versions with explosion protection for hazardous area zone II (ATEX II 3G):
Safety Instructions for use in explosion-hazardous areas, XA194C/07/A3
Accessories
Sensors Glass sensors
Orbisint CPS11/CPS11D
• pH sensor for process applications
• Optional SIL version for connection to SIL approved transmitters
• With dirt-repellent PTFE diaphragm
• Ordering acc. to product structure, see Technical Information (TI028C/07/en)
Orbisint CPS12/CPS12D
• ORP electrode for process applications
• With dirt-repellent PTFE diaphragm
• Ordering acc. to product structure, see Technical Information (TI367C/07/en)
Ceraliquid CPS41/CPS41D
• pH sensor
• With ceramics diaphragm and liquid KCl electrolyte
• Ordering acc. to product structure, see Technical Information (TI079C/07/en)
Ceraliquid CPS42/CPS42D
• ORP electrode
• With ceramics diaphragm and liquid KCl electrolyte
• Ordering acc. to product structure, see Technical Information (TI373C/07/en)
Ceragel CPS71/CPS71D
• pH sensor
• With double chamber reference system and integrated bridge electrolyte
• Ordering acc. to product structure, see Technical Information (TI245C/07/en)
Ceragel CPS72/CPS72D
• ORP electrode
• With double chamber reference system and integrated bridge electrolyte
• Ordering acc. to product structure, see Technical Information (TI374C/07/en)
Orbipore CPS91/CPS91D
• pH sensor
• With open aperture for media with high dirt load
• Ordering acc. to product structure, see Technical Information (TI375C/07/en)
19. Liquisys M CPM223/253
Endress+Hauser 19
Orbipore CPS92/CPS92D
• ORP sensor
• With open aperture for media with high dirt load
• Ordering acc. to product structure, see Technical Information (TI435C/07/en)
ISFET sensors
Tophit CPS471
• Sterilizable and autoclavable ISFET sensor
• For food and pharmaceuticals, process technology, water treatment and biotechnology;
• Ordering acc. to product structure, see Technical Information (TI283C/07/en)
Tophit CPS441
• Sterilizable ISFET sensor for media with low conductivity
• With liquid KCl electrolyte
• Ordering acc. to product structure, see Technical Information (TI352C/07/en)
Tophit CPS491
• ISFET sensor with open aperture for media with high dirt load
• Ordering acc. to product structure, see Technical Information (TI377C/07/en)
Connection accessories CPK9 special measuring cable
• For sensors with TOP68 plug-in head, for high-temperature and high-pressure applications, IP 68
• Ordering acc. to product structure, see Technical Information (TI118C/07/en)
CPK1 special measuring cable
• For pH/ORP electrodes with GSA plug-in head
• Ordering acc. to product structure, see Technical Information (TI118C/07/en)
CPK2 special measuring cable
• For pH/ORP electrodes with GSA plug-in head, with three sensor plugs
• Ordering acc. to product structure, see Technical Information (TI 118C/07/en)
CPK12 special measuring cable
• For pH/ORP glass electrodes and ISFET sensors with TOP68 plug-in head
• Ordering acc. to product structure, see Technical Information (TI118C/07/en)
CYK10 Data cable for digital sensors
• For digital pH sensors with Memosens technology
• Ordering according to product structure, see below
Certificates
A Standard, non Ex
G ATEX II 1G EEx ia IIC T6/T4
O FM CI.I Div. 1 AEx ia IIC T6/T4
S CSA IS CI.I Ex ia IIC T6/T4
Cable length
03 Cable length: 3 m / 9.84 ft
05 Cable length: 5 m / 16.41 ft
10 Cable length: 10 m / 32.81 ft
15 Cable length: 15 m / 49.22 ft
20 Cable length: 20 m / 65.62 ft
25 Cable length: 25 m / 82.03 ft
88 ... m length
89 ... ft length
Ready-made
1 Wire terminals
CYK10- complete order code
20. Liquisys M CPM223/253
20 Endress+Hauser
CYK81 measuring cable
• Non-terminated measuring cable for extension of sensor cables of e.g. Memosens sensors, CUS31/CUS41
• 2 wires, twisted pair with shield and PVC-sheath (2 x 2 x 0.5 mm2
+ shield)
• Sold by the meter, order no.: 51502543
Junction box VBM
• For cable extension
• 10 terminals
• Cable entries: 2 x Pg 13.5 or 2 x NPT ½"
• Material: aluminum
• Ingress protection: IP 65 (i NEMA 4X)
• Order numbers:
– cable entries Pg 13.5: 50003987
– cable entries NPT ½": 51500177
Junction box VBA
• For cable extension of pH/ORP sensors
• 10 terminals, protection class: IP 65 (i NEMA 4X)
• Cable entries: 2 x Pg 13.5, 2 x Pg 16
• Material: polycarbonate
• Order no.: 50005276
Junction box RM
• For cable extension (e.g. for Memosens sensors)
• 5 terminals
• Cable entries: 2 x Pg 13.5
• Material: PC
• Ingress protection: IP 65
• Order no.: 51500832
Mounting accessories CYY101 weather protection cover for field devices, absolutely essential if operating the unit outdoors
• Material: stainless steel 1.4031 (AISI 304)
• Order No. CYY101-A
a0012427
Weather protection cover for field devices
* Wall and post mounting
** Rail mounting
21. Liquisys M CPM223/253
Endress+Hauser 21
Post mounting kit
• For mounting of field housing on horizontal or vertical pipes (Ø max. 60 mm (2.36"))
• Material: stainless steel 1.4301
• order no. 50086842
a0005676
Post mounting kit
CYY102 universal post
• Square pipe for mounting transmitters
• Material: stainless steel 1.4301 (AISI 304)
• Order No. CYY102-A
a0005742
Universal post
70 / 2.76
90 / 3.54
Ø 6 / 0.24
Ø8/
0.31
70/2.76
90/3.54
M6
60/2.36
90 / 3.54
70 / 2.76
Ø8/
0.31
30/
1.18
Ø max. 60 / 2.36
mm / inch
1495/58.86
60 x 60 /
2.36 x 2.36
120 /
4.72
150/
5.91
mm/inch
22. Liquisys M CPM223/253
22 Endress+Hauser
Buffer solutions High-quality buffer solutions of Endress+Hauser - CPY20
The secondary buffer solutions have been referenced to primary reference material of the PTB (German Federal
Physico-technical Institute) and to standard reference material of NIST (National Institute of Standards and
Technology) according to DIN 19266 by a DKD (German Calibration Service) accredited laboratory.
Technical buffer solutions for ORP electrodes
• +220 mV, pH 7.0, 100 ml (3.4 fl.oz.); order no. CPY3-0
• +468 mV, pH 0.1, 100 ml (3.4 fl.oz.); order no. CPY3-1
KCl-electrolyte solutions for liquid filled electrodes
• 3.0 mol, T = -10 ... 100 °C (14 ... 212 °F), 100 ml (3.4 fl.oz.), order no. CPY4-1
• 3.0 mol, T = -10 ... 100 °C (14 ... 212 °F), 1000 ml (34 fl.oz.), order no. CPY4-2
• 1.5 mol, T = -30 ... 100 °C (-22 ... 266 °F), 100 ml (3.4 fl.oz.), order no. CPY4-3
• 1.5 mol, T = -30 ... 100 °C (-22 ... 266 °F), 1000 ml (34 fl.oz.), order no. CPY4-4
Optoscope Optoscope
• Interface between transmitter and PC / laptop for service purposes.
• The Windows software "Scopeware" required for the PC or laptop is supplied with the Optoscope. The
Optoscope is supplied in a sturdy plastic case with all the accessories required.
• Order no. 51500650
pH value
A pH 2.00 (accuracy ± 0.02 pH)
C pH 4.00 (accuracy ± 0.02 pH)
E pH 7.00 (accuracy ± 0.02 pH)
G pH 9.00 (accuracy ± 0.02 pH)
I pH 9.20 (accuracy ± 0.02 pH)
K pH 10.00 (accuracy ± 0.05 pH)
M pH 12.00 (accuracy ± 0.05 pH)
Quantity
01 20 x 18 ml (0.68 fl.oz) only buffer solutions pH 4.00 and 7.00
02 250 ml (8.45 fl.oz)
10 1000 ml (0.26 US gal)
50 5000 ml (1.32 US gal) canister for Topcal S
Certificates
A Buffer analysis certificate
Version
1 Standard
CPY20- complete order code