This paper presents an investigation of five-Level
Cascaded H-bridge(CHB) inverter as Active Power Filter in
Power System (PS) for compensation of reactive power and
harmonics. The advantages of CHB inverter are low harmonic
distortion, reduced number of switches and suppression of
switching losses. The Active Power Filter helps to improve
the power factor and eliminate the Total Harmonics Distortion
(THD) drawn from a Non-Liner Diode Rectifier Load (NLDRL).
The D-Q reference frame theory is used to generate the
reference compensating currents for Active Power Filter
while Neuro-Fuzzy controller(NFC) is used for capacitor dc
voltage regulation. A CHB Inverter is considered for shunt
compensation of a 11 kV distribution system. Finally a level
shifted PWM (LSPWM) technique adopted to investigate the
performance of CHB Inverter. The results are obtained through
Mat lab / Simulink .
A Novel Compensating Technique for Power Factor Improvement in Power Electron...IDES Editor
Power electronics systems are non-linear systems,
which consume more reactive power and also the loads they
feed are mostly inductive loads which leads to a poor power
factor. Various compensation techniques are available to bring
the power factor nearer to unity. In this paper, a novel
compensator is proposed, where in-phase and quadrature
components of the supply current are vector-controlled.
Implementation of this compensator in a power electronic
system operating with a very poor power factor (and hence
high THD), shows that the system then draws a leading
current. A conventional power electronic system, A
conventional power electronic system with one of the
traditional static VAR compensators and the conventional
power electronic system incorporated with the proposed
compensator are simulated and the simulation results are
obtained. It is shown that the proposed method offers only
0.7% THD, which also implies that the power factor is
improved.
Open Loop Control Of Series Parallel Resonant ConverterIDES Editor
Resonant converters are desirable for power
conversion due to their comparatively smaller size and
lower power losses resulting from high-frequency
operation and inherent soft switching. Among all the
topologies of the resonant converters, the series–parallel
resonant converter (SPRC) is known to have the
combined merits of the series resonant converter and
parallel resonant converter. The converter can regulate
the output voltage at a constant switching frequency even
for a change in load resistance from full load resistance to
infinity while maintaining good part load efficiency. The
purpose of this project is to design a closed loop
controller for the phase-controlled series parallel
resonant converter (PC SPRC). The open loop analysis
and closed loop control has been provided in this paper.
Abstract: AC-DC soft-switching resonant converter with interleaved boost power factor corrector (PFC) is presented. In this converter, an interleaved boost PFC circuit is integrated with a soft-switching resonant converter. High power factor is achieved by the interleaved boost PFC circuit. The input current can be shared among the inductors so that high reliability, power factor and efficiency in power system can be obtained and ripples are also reduced. Another advantage of interleaved technique is reduction of THD. Thus the converter performance can be improved. The voltage across the main switches is confined to the dc-link voltage. Soft-switching operation of main switches and output diodes is achieved. Hence the switching losses are reduced significantly. Therefore, the overall efficiency is improved. Circuit is simulated with 110V AC input voltage and 45V DC output voltage is verified. Performance parameters such as voltage stress and output ripple are also analyzed. The simulation is done in PSIM. Power factor of 0.96 is achieved with this converter. For the hardware, dsPIC30F2010 is used for generating PWM pulse with switching frequency 90 kHz.
Keywords: Power factor correction (PFC), Soft switching, Resonant converter, Interleaved Boost converter.
Title: Resonant AC-DC Converter with Interleaved Boost PFC
Author: Aqulin Ouseph, Prof. Kiran Boby, Prof. Neena Mani
ISSN 2349-7815
International Journal of Recent Research in Electrical and Electronics Engineering (IJRREEE)
Paper Publications
A Novel Fuzzy Variable-Band Hysteresis Current Controller For Shunt Active Po...IDES Editor
This paper presents a novel fuzzy control scheme
applied to shunt active power filters for harmonic and reactive
power compensation. A TSK type fuzzy logic controller is
proposed for APF reference current generation. To control
the maximum switching frequency of the converter within
limit a novel fuzzy hysteresis band current controller is used.
The band height, based on fuzzy control principle is changed
with the value of supply voltage and slope of reference current
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Reactive Power Compensation in 132kv & 33kv Grid of Narsinghpur Areaijceronline
Power Sector is considered to be very important and priority sector as it leads to overall development of country. The cost of installation of new generating units is rising; hence generated electrical energy has to be utilized carefully and efficiently, which changes through each AC cycle. It is proposed to study the effect of group shunt compensation provided for the mix of rural and urban loads, catered from grid sub-stations in the district of Narsinghpur, to assess its adequacy and saving in transmission losses. An optimum combination of compensators which yields maximum benefits in the system shall be worked out. Load Flow Study for the effect of group shunt compensation provided on 132KV bus of 220KV sub-station Narsinghpur and on 33KV buses of 132KV sub stations Srinagar, Narsinghpur, Gadarwara and Burman sub-stations for the mix of rural and urban loads, catered from partial grid network in Narsinghpur district. If reactive power is supplied near the load, the line current can be reduced or minimized, reducing power losses and improving voltage regulation at the load terminals. The leading current drawn by the shunt capacitors compensates the lagging current drawn by the load. The selection of shunt capacitors depends on many factors, the most important of which is the amount of lagging reactive power taken by the load. Objective was to study the effect of group shunt compensation provided for the mix of rural and urban loads, catered from grid sub-stations in the district of Narsinghpur and to assess the adequacy and saving in transmission losses & to work out an optimum combination of compensators which yields maximum benefits in the system. Depending on the stages of 'ON' and 'OFF', operations to be carried out in various permutations and combinations of shunt compensators i.e. switchable capacitor banks provided on 132 KV bus of 220KV substation Narsinghpur and on 33KV buses of 132 KV substations
A Novel Compensating Technique for Power Factor Improvement in Power Electron...IDES Editor
Power electronics systems are non-linear systems,
which consume more reactive power and also the loads they
feed are mostly inductive loads which leads to a poor power
factor. Various compensation techniques are available to bring
the power factor nearer to unity. In this paper, a novel
compensator is proposed, where in-phase and quadrature
components of the supply current are vector-controlled.
Implementation of this compensator in a power electronic
system operating with a very poor power factor (and hence
high THD), shows that the system then draws a leading
current. A conventional power electronic system, A
conventional power electronic system with one of the
traditional static VAR compensators and the conventional
power electronic system incorporated with the proposed
compensator are simulated and the simulation results are
obtained. It is shown that the proposed method offers only
0.7% THD, which also implies that the power factor is
improved.
Open Loop Control Of Series Parallel Resonant ConverterIDES Editor
Resonant converters are desirable for power
conversion due to their comparatively smaller size and
lower power losses resulting from high-frequency
operation and inherent soft switching. Among all the
topologies of the resonant converters, the series–parallel
resonant converter (SPRC) is known to have the
combined merits of the series resonant converter and
parallel resonant converter. The converter can regulate
the output voltage at a constant switching frequency even
for a change in load resistance from full load resistance to
infinity while maintaining good part load efficiency. The
purpose of this project is to design a closed loop
controller for the phase-controlled series parallel
resonant converter (PC SPRC). The open loop analysis
and closed loop control has been provided in this paper.
Abstract: AC-DC soft-switching resonant converter with interleaved boost power factor corrector (PFC) is presented. In this converter, an interleaved boost PFC circuit is integrated with a soft-switching resonant converter. High power factor is achieved by the interleaved boost PFC circuit. The input current can be shared among the inductors so that high reliability, power factor and efficiency in power system can be obtained and ripples are also reduced. Another advantage of interleaved technique is reduction of THD. Thus the converter performance can be improved. The voltage across the main switches is confined to the dc-link voltage. Soft-switching operation of main switches and output diodes is achieved. Hence the switching losses are reduced significantly. Therefore, the overall efficiency is improved. Circuit is simulated with 110V AC input voltage and 45V DC output voltage is verified. Performance parameters such as voltage stress and output ripple are also analyzed. The simulation is done in PSIM. Power factor of 0.96 is achieved with this converter. For the hardware, dsPIC30F2010 is used for generating PWM pulse with switching frequency 90 kHz.
Keywords: Power factor correction (PFC), Soft switching, Resonant converter, Interleaved Boost converter.
Title: Resonant AC-DC Converter with Interleaved Boost PFC
Author: Aqulin Ouseph, Prof. Kiran Boby, Prof. Neena Mani
ISSN 2349-7815
International Journal of Recent Research in Electrical and Electronics Engineering (IJRREEE)
Paper Publications
A Novel Fuzzy Variable-Band Hysteresis Current Controller For Shunt Active Po...IDES Editor
This paper presents a novel fuzzy control scheme
applied to shunt active power filters for harmonic and reactive
power compensation. A TSK type fuzzy logic controller is
proposed for APF reference current generation. To control
the maximum switching frequency of the converter within
limit a novel fuzzy hysteresis band current controller is used.
The band height, based on fuzzy control principle is changed
with the value of supply voltage and slope of reference current
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Reactive Power Compensation in 132kv & 33kv Grid of Narsinghpur Areaijceronline
Power Sector is considered to be very important and priority sector as it leads to overall development of country. The cost of installation of new generating units is rising; hence generated electrical energy has to be utilized carefully and efficiently, which changes through each AC cycle. It is proposed to study the effect of group shunt compensation provided for the mix of rural and urban loads, catered from grid sub-stations in the district of Narsinghpur, to assess its adequacy and saving in transmission losses. An optimum combination of compensators which yields maximum benefits in the system shall be worked out. Load Flow Study for the effect of group shunt compensation provided on 132KV bus of 220KV sub-station Narsinghpur and on 33KV buses of 132KV sub stations Srinagar, Narsinghpur, Gadarwara and Burman sub-stations for the mix of rural and urban loads, catered from partial grid network in Narsinghpur district. If reactive power is supplied near the load, the line current can be reduced or minimized, reducing power losses and improving voltage regulation at the load terminals. The leading current drawn by the shunt capacitors compensates the lagging current drawn by the load. The selection of shunt capacitors depends on many factors, the most important of which is the amount of lagging reactive power taken by the load. Objective was to study the effect of group shunt compensation provided for the mix of rural and urban loads, catered from grid sub-stations in the district of Narsinghpur and to assess the adequacy and saving in transmission losses & to work out an optimum combination of compensators which yields maximum benefits in the system. Depending on the stages of 'ON' and 'OFF', operations to be carried out in various permutations and combinations of shunt compensators i.e. switchable capacitor banks provided on 132 KV bus of 220KV substation Narsinghpur and on 33KV buses of 132 KV substations
Mitigation of Harmonic Current through Hybrid Power Filter in Single Phase Re...IDES Editor
This paper presents a single-phase Hybrid Power
Filter (HPF) for harmonics and reactive power compensation.
This proposed topology reduces the rating and size of the
filter components. A combination of Passive and Active Filter
is proposed for reducing the rating of filter. In the proposed
technique Passive Filter (PF) is tuned to compensate 3rd and
5th order harmonics and Active Power Filter (APF) compensates
all remaining harmonic components which are not
compensated by passive filter. A half bridge inverter with DC
bus capacitor is used as active filter. It has only two power
switches. The active power filter control is based on DC side
voltage control. The effectiveness of the proposed algorithm
is demonstrated by its simulation in PSIM software. The
simulation results show that the designed hybrid filter
compensate the harmonic currents produced by loads and the
power factor, making the current at the source side to become
sinusoidal and in phase with the system voltage.
10 17sep 8310 10079-1-ed pulse density (edit ari)IAESIJEECS
Switched mode power supply (SMPS) converter is a dc-dc power electronic converter which is used to step up or step down the dc output voltage. A dimmable driver circuit for Light Emitting Diode (LED) lamp for automotive lighting with dimming feature is used in this paper. A flyback converter is used as a driver circuit operated in discontinuous conduction mode to perform dimming control of LEDs. High overall circuit efficiency is achieved by regulating the current through the LED lamps using pulse density modulation scheme. The LED driver circuit design and operating principle is discussed in detail. A gentle current control feature is achieved by pulse density modulation technique. The high performance driver circuit is designed for 25 W LED lamps.
Adaptive Modified Minimally Switched Hysteresis Controlled Shunt Active Power...idescitation
The main focus of this article is to investigate the
effects of Adaptive control on the switching frequency and
Total Harmonic Distortion of a modified, minimally switched
hysteresis controlled shunt active power filter. Reference
current generation was done using Instantaneous real and
reactive power algorithm. Pulses to the minimally switched
grid interactive inverter in which only two switches are
controlled at a time, had been generated using a modified
hysteresis current controller. Use of Modified Hysteresis
controller results in reducing the switching loses to one-third
but results in increase in current THD than the conventional
hysteresis controller. To overcome this, pulses to the modified
hysteresis controller were generated employing adaptive
control by modifying pulses from a conventional hysteresis
controller. Using adaptive control instantaneous switching
frequency was reduced and maintained nearly constant and
THD was brought to the limits specified by the standards,
thus overcoming the disadvantage of conventional and modified
hysteresis controller which has variable switching frequency.
A comparison of Modified Hysteresis controller with and
without Adaptive control has been made, to show the reduction
in THD. The system was simulated using MATLAB-
SIMULINK.
This paper presents the simulation design of dc/dc interleaved boost converter with zero-voltage switching (ZVS). By employin the interleaved structure, the input current stresses to switching devices were reduced and this signified to a switching conduction loss reduction. All the parameters had been calculated theoretically. The proposed converter circuit was simulated by using MATLAB/Simulink and PSpice software programmes. The converter circuit model, with specifications of output power of 200 W, input voltage range from 10~60 V, and operates at 100 kHz switching frequency was simulated to validate the designed parameters. The results showed that the main switches of the model converter circuit achieved ZVS conditions during the interleaving operation. Consequently, the switching losses in the main switching devices were reduced. Thus, the proposed converter circuit model offers advantages of input current stress and switching loss reductions. Hence, based on the designed parameters and results, the converter model can be extended for hardware implementation.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Passive Damper Network in a Simple DC Distribution Power System IJECEIAES
Distributed power system (DPS) distributes power amongst processing units such as power electronics converters with DC system. Due to the increasing usage of power converters in DPS system, the system becomes unstable and the converter tends to draw constant power needed by the load of the system. Constant power load (CPL) characteristic has negative input impedance that could produce instability problems in the DC bus system. Passive damping network which consists of series RC damping circuit was connected in parallel to the DC bus system with the purpose to reduce the instability. The passive damper was designed, simulated with MATLAB/Simulink and verified experimentally with different values of CPL power levels and input voltage changes. The obtained simulation results show that simple DC system with constant power load was successfully stabilized by the installation of the passive damping network. The experimental set up was also conducted to validate of the proposed technique, and the obtained results were in excellent agreement with the theoretical parts of the project.
International Journal of Engineering and Science Invention (IJESI)inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Power Quality Enhancement in Power Distribution system using Artificial intel...sundar balan
Dynamic voltage Restorer
Artificial intelligence based Dynamic voltage restorer
DVR
Artificial neural network based DVR dynamic voltage restorer
Harmonics voltage harmonics voltage sag voltage swell
Power Quality Enhancement in Power Distribution system using Artificial intelligence based Dynamic Voltage Restorer
Comparison of Buck-Boost and Cuk Converters for BLDC Drive Applications with PFCIJMTST Journal
The devices generally used in industrial, commercial and residential applications need to undergo rectification for their proper functioning and operation. Hence there is a need to reduce the line current harmonics so as to improve the power factor of the system. This has led to designing of Power Factor Correction circuits. This project presents a power factor corrected (PFC) bridgeless (BL) buck–boost converter-fed brushless direct current (BLDC) motor drive as a cost-effective solution for low-power applications. The conventional PFC scheme of the BLDC motor drive utilizes a pulse width-modulated voltage source inverter (PWM-VSI) for speed control with a constant dc link voltage. This offers higher switching losses in VSI as the switching losses increase as a square function of switching frequency. A BL configuration of the buck–boost converter is proposed which offers the elimination of the diode bridge rectifier, thus reducing the conduction losses associated with it. A PFC BL buck–boost converter is designed to operate in discontinuous inductor current mode (DICM) to provide an inherent PFC at ac mains. The simulation results are presented by using Matlab/Simulink software. The proposed concept can be extended with cuk converter for BLDC drive applications using Matlab/Simulink software
Fuzzy Logic Controller based Bridgeless (BL) Isolated Interleaved Zeta Conver...IJPEDS-IAES
In recent times, high-brightness light emitting diodes (HB-LEDs) are
developing rapidly and it is confirmed to be the future development in
lighting not only because of their high efficiency and high reliability,
however also because of their other exceptional features: chromatic variety,
shock and vibration resistance, etc. In this paper, a bridgeless (BL) Isolated
Interleaved Zeta Converter is proposed for the purpose of reducing the diode
failures or losses; the value of output ripples also gets decreased. The
proposed BL isolated interleaved zeta converter operating in discontinuous
conduction mode (DCM) is used for controlling the brightness of LED
Driver with inherent PFC at ac mains using single voltage sensor. The fuzzy
logic controller (FLC) is used to adjust the Modulation Index of the voltage
controller in order to improve the dynamic response of LED Lamp driver.
Based on the error of converter output voltage, FLC is designed to select the
optimum Modulation Index of the voltage controller. The proposed LED
driver is simulated to achieve a unity power factor at ac mains for a wide
range of voltage control and supply voltage fluctuations.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Design and Simulation of Power Factor Correction Boost Converter using Hyster...ijtsrd
Nowadays various power converters like AC DC or DC DC are widely used due to their flexible output voltage and high efficiency. But these converters take the current in the form of pulses from the utility grid so that the high Total Harmonic Distortion THD and poor Power Factor PF are the major disadvantages of these converters. Hence there is a continuous need for PF improvement and reduction of line current harmonics. The most popular topology for Active Power Factor Correction APFC is a boost converter as it draws continuous input current. This input current can be manipulated by Hysteresis control technique. The boost converter can perform this type of active power factor correction in many discontinuous and continuous modes. The design and simulation of boost converter with power factor correction in continuous conduction mode is represented by using MATLAB SIMULINK software. Yu Yu Khin | Yan Aung Oo "Design and Simulation of Power Factor Correction Boost Converter using Hysteresis Control" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd27905.pdfPaper URL: https://www.ijtsrd.com/engineering/electrical-engineering/27905/design-and-simulation-of-power-factor-correction-boost-converter-using-hysteresis-control/yu-yu-khin
POWER STABILITY ANALYSIS OF A TRANSMISSION SYSTEM WITH A UNIFIED POWER FLOW C...IJITE
The unified power quality conditioner is the equipment used for regulated voltage distortion and voltage
unbalance in a power system. UPFC can enhance the power to flow through the transmission system by
controlling the power flow and voltage stability of the transmission line within their limits. This paper
presents a control scheme and Theoretical derivation of the unified power flow conditioner and the
simulation results are compared and contrasted in detail. UPFC is a combination of shunt Active and
series active power filters. UPFC contains a DC link capacitor in a single-phase voltage source inverter
with two back to back connected, three-phase three-wire and three-phase four-wire are arranged. The
fundamental target of this work is to determine the causes and impacts of power quality problems,
specifically voltage sag, voltage swell, power factor, and Total Harmonics Distortion (THD) and enhance
the power quality of a transmission system by UPFC based Transformative Intrinsic Algorithm (TIA). The
Simulation of the proposed method is developed by Mat lab Simulink software, and the simulation result
shows, the proposed method gives better solutions to control the power imbalance in the distribution
system with its cost-effectiveness.
Open-End-Winding Permanent Magnet Synchonous Generator for Wind Energy Conver...Naila Syed
Recent trend in Wind energy conversion system which helps in understanding how the control systems and power energy systems can be interfaced to make the best use of wind energy.
Mitigation of Harmonic Current through Hybrid Power Filter in Single Phase Re...IDES Editor
This paper presents a single-phase Hybrid Power
Filter (HPF) for harmonics and reactive power compensation.
This proposed topology reduces the rating and size of the
filter components. A combination of Passive and Active Filter
is proposed for reducing the rating of filter. In the proposed
technique Passive Filter (PF) is tuned to compensate 3rd and
5th order harmonics and Active Power Filter (APF) compensates
all remaining harmonic components which are not
compensated by passive filter. A half bridge inverter with DC
bus capacitor is used as active filter. It has only two power
switches. The active power filter control is based on DC side
voltage control. The effectiveness of the proposed algorithm
is demonstrated by its simulation in PSIM software. The
simulation results show that the designed hybrid filter
compensate the harmonic currents produced by loads and the
power factor, making the current at the source side to become
sinusoidal and in phase with the system voltage.
10 17sep 8310 10079-1-ed pulse density (edit ari)IAESIJEECS
Switched mode power supply (SMPS) converter is a dc-dc power electronic converter which is used to step up or step down the dc output voltage. A dimmable driver circuit for Light Emitting Diode (LED) lamp for automotive lighting with dimming feature is used in this paper. A flyback converter is used as a driver circuit operated in discontinuous conduction mode to perform dimming control of LEDs. High overall circuit efficiency is achieved by regulating the current through the LED lamps using pulse density modulation scheme. The LED driver circuit design and operating principle is discussed in detail. A gentle current control feature is achieved by pulse density modulation technique. The high performance driver circuit is designed for 25 W LED lamps.
Adaptive Modified Minimally Switched Hysteresis Controlled Shunt Active Power...idescitation
The main focus of this article is to investigate the
effects of Adaptive control on the switching frequency and
Total Harmonic Distortion of a modified, minimally switched
hysteresis controlled shunt active power filter. Reference
current generation was done using Instantaneous real and
reactive power algorithm. Pulses to the minimally switched
grid interactive inverter in which only two switches are
controlled at a time, had been generated using a modified
hysteresis current controller. Use of Modified Hysteresis
controller results in reducing the switching loses to one-third
but results in increase in current THD than the conventional
hysteresis controller. To overcome this, pulses to the modified
hysteresis controller were generated employing adaptive
control by modifying pulses from a conventional hysteresis
controller. Using adaptive control instantaneous switching
frequency was reduced and maintained nearly constant and
THD was brought to the limits specified by the standards,
thus overcoming the disadvantage of conventional and modified
hysteresis controller which has variable switching frequency.
A comparison of Modified Hysteresis controller with and
without Adaptive control has been made, to show the reduction
in THD. The system was simulated using MATLAB-
SIMULINK.
This paper presents the simulation design of dc/dc interleaved boost converter with zero-voltage switching (ZVS). By employin the interleaved structure, the input current stresses to switching devices were reduced and this signified to a switching conduction loss reduction. All the parameters had been calculated theoretically. The proposed converter circuit was simulated by using MATLAB/Simulink and PSpice software programmes. The converter circuit model, with specifications of output power of 200 W, input voltage range from 10~60 V, and operates at 100 kHz switching frequency was simulated to validate the designed parameters. The results showed that the main switches of the model converter circuit achieved ZVS conditions during the interleaving operation. Consequently, the switching losses in the main switching devices were reduced. Thus, the proposed converter circuit model offers advantages of input current stress and switching loss reductions. Hence, based on the designed parameters and results, the converter model can be extended for hardware implementation.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Passive Damper Network in a Simple DC Distribution Power System IJECEIAES
Distributed power system (DPS) distributes power amongst processing units such as power electronics converters with DC system. Due to the increasing usage of power converters in DPS system, the system becomes unstable and the converter tends to draw constant power needed by the load of the system. Constant power load (CPL) characteristic has negative input impedance that could produce instability problems in the DC bus system. Passive damping network which consists of series RC damping circuit was connected in parallel to the DC bus system with the purpose to reduce the instability. The passive damper was designed, simulated with MATLAB/Simulink and verified experimentally with different values of CPL power levels and input voltage changes. The obtained simulation results show that simple DC system with constant power load was successfully stabilized by the installation of the passive damping network. The experimental set up was also conducted to validate of the proposed technique, and the obtained results were in excellent agreement with the theoretical parts of the project.
International Journal of Engineering and Science Invention (IJESI)inventionjournals
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Power Quality Enhancement in Power Distribution system using Artificial intel...sundar balan
Dynamic voltage Restorer
Artificial intelligence based Dynamic voltage restorer
DVR
Artificial neural network based DVR dynamic voltage restorer
Harmonics voltage harmonics voltage sag voltage swell
Power Quality Enhancement in Power Distribution system using Artificial intelligence based Dynamic Voltage Restorer
Comparison of Buck-Boost and Cuk Converters for BLDC Drive Applications with PFCIJMTST Journal
The devices generally used in industrial, commercial and residential applications need to undergo rectification for their proper functioning and operation. Hence there is a need to reduce the line current harmonics so as to improve the power factor of the system. This has led to designing of Power Factor Correction circuits. This project presents a power factor corrected (PFC) bridgeless (BL) buck–boost converter-fed brushless direct current (BLDC) motor drive as a cost-effective solution for low-power applications. The conventional PFC scheme of the BLDC motor drive utilizes a pulse width-modulated voltage source inverter (PWM-VSI) for speed control with a constant dc link voltage. This offers higher switching losses in VSI as the switching losses increase as a square function of switching frequency. A BL configuration of the buck–boost converter is proposed which offers the elimination of the diode bridge rectifier, thus reducing the conduction losses associated with it. A PFC BL buck–boost converter is designed to operate in discontinuous inductor current mode (DICM) to provide an inherent PFC at ac mains. The simulation results are presented by using Matlab/Simulink software. The proposed concept can be extended with cuk converter for BLDC drive applications using Matlab/Simulink software
Fuzzy Logic Controller based Bridgeless (BL) Isolated Interleaved Zeta Conver...IJPEDS-IAES
In recent times, high-brightness light emitting diodes (HB-LEDs) are
developing rapidly and it is confirmed to be the future development in
lighting not only because of their high efficiency and high reliability,
however also because of their other exceptional features: chromatic variety,
shock and vibration resistance, etc. In this paper, a bridgeless (BL) Isolated
Interleaved Zeta Converter is proposed for the purpose of reducing the diode
failures or losses; the value of output ripples also gets decreased. The
proposed BL isolated interleaved zeta converter operating in discontinuous
conduction mode (DCM) is used for controlling the brightness of LED
Driver with inherent PFC at ac mains using single voltage sensor. The fuzzy
logic controller (FLC) is used to adjust the Modulation Index of the voltage
controller in order to improve the dynamic response of LED Lamp driver.
Based on the error of converter output voltage, FLC is designed to select the
optimum Modulation Index of the voltage controller. The proposed LED
driver is simulated to achieve a unity power factor at ac mains for a wide
range of voltage control and supply voltage fluctuations.
International Journal of Engineering Research and DevelopmentIJERD Editor
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
Design and Simulation of Power Factor Correction Boost Converter using Hyster...ijtsrd
Nowadays various power converters like AC DC or DC DC are widely used due to their flexible output voltage and high efficiency. But these converters take the current in the form of pulses from the utility grid so that the high Total Harmonic Distortion THD and poor Power Factor PF are the major disadvantages of these converters. Hence there is a continuous need for PF improvement and reduction of line current harmonics. The most popular topology for Active Power Factor Correction APFC is a boost converter as it draws continuous input current. This input current can be manipulated by Hysteresis control technique. The boost converter can perform this type of active power factor correction in many discontinuous and continuous modes. The design and simulation of boost converter with power factor correction in continuous conduction mode is represented by using MATLAB SIMULINK software. Yu Yu Khin | Yan Aung Oo "Design and Simulation of Power Factor Correction Boost Converter using Hysteresis Control" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd27905.pdfPaper URL: https://www.ijtsrd.com/engineering/electrical-engineering/27905/design-and-simulation-of-power-factor-correction-boost-converter-using-hysteresis-control/yu-yu-khin
POWER STABILITY ANALYSIS OF A TRANSMISSION SYSTEM WITH A UNIFIED POWER FLOW C...IJITE
The unified power quality conditioner is the equipment used for regulated voltage distortion and voltage
unbalance in a power system. UPFC can enhance the power to flow through the transmission system by
controlling the power flow and voltage stability of the transmission line within their limits. This paper
presents a control scheme and Theoretical derivation of the unified power flow conditioner and the
simulation results are compared and contrasted in detail. UPFC is a combination of shunt Active and
series active power filters. UPFC contains a DC link capacitor in a single-phase voltage source inverter
with two back to back connected, three-phase three-wire and three-phase four-wire are arranged. The
fundamental target of this work is to determine the causes and impacts of power quality problems,
specifically voltage sag, voltage swell, power factor, and Total Harmonics Distortion (THD) and enhance
the power quality of a transmission system by UPFC based Transformative Intrinsic Algorithm (TIA). The
Simulation of the proposed method is developed by Mat lab Simulink software, and the simulation result
shows, the proposed method gives better solutions to control the power imbalance in the distribution
system with its cost-effectiveness.
Open-End-Winding Permanent Magnet Synchonous Generator for Wind Energy Conver...Naila Syed
Recent trend in Wind energy conversion system which helps in understanding how the control systems and power energy systems can be interfaced to make the best use of wind energy.
Study of Permanent Magnent Synchronous MacnineRajeev Kumar
With respect of designing a PMSG, the permanent magnetic pole lies on the rotor and armature winding are in the inner part of stator that is electrically connected to the load. Armature winding consists of the set of three conductors which has phase difference 120 derg apart to each other and providing a uniform force or torque on the generator’s rotor. To operate PMGS, it is connected to wind turbine through a shaft without gear box and rotate at slow speed. This uniform torque produced by the resultant magnetic flux which induces current in the armature winding. The stator magnetic field combined spatially with rotor magnetic flux and rotates as the same speed of the rotor. So the two magnetic fields synchronously rotate in PGSM to maintain the relative motion of rotor and stator.
Thus the permanent magnets rotates at constant speed without any DC excitation system, which means it has not required any slip rings and contact brushes to make it more reliability or efficient.
This ppt shows the modelling and simulation of permanent magnet synchronous motor by using torque control method.
And this is the most advanced and soffestigated method to control the pmsm motors.
In recent years, Permanent Magnet Synchronous Machines (PMSMs) are increasing
applied in several areas such as generation, traction, automobiles, robotics and aerospace
technology. Basically PMSG topology has been beneficial for slow speed and variable speed
operation and steady state output power produced in operation. PMSG is a part of
synchronous machine family, so its construction features almost equivalent to synchronous
machine.
With respect of designing a PMSG, the permanent magnetic pole lies on the rotor and
armature winding are in the inner part of stator that is electrically connected to the load.
Armature winding consists of the set of three conductors which has phase difference 1200
apart to each other and providing a uniform force or torque on the generator’s rotor. To
operate PMGS, it is connected to wind turbine through a shaft without gear box and rotate at
slow speed. This uniform torque produced by the resultant magnetic flux which induces
current in the armature winding. The stator magnetic field combined spatially with rotor
magnetic flux and rotates as the same speed of the rotor. So the two magnetic fields
synchronously rotate in PGSM to maintain the relative motion of rotor and stator.
Thus the permanent magnets rotates at constant speed without any DC excitation system,
which means it has not required any slip rings and contact brushes to make it more reliability
or efficient.
Independent control of two permanent magnet synchronous motors fed by a four-...LeMeniz Infotech
Independent control of two permanent magnet synchronous motors fed by a four-leg inverter
To Get this projects Call : 9566355386 / 99625 88976
Visit : www.lemenizinfotech.com / www.ieeemaster.com
Mail : projects@lemenizinfotech.com
Research Inventy : International Journal of Engineering and Scienceresearchinventy
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
Design of UPQC with Minimization of DC Link voltage for the Improvement of Po...IDES Editor
Devices such as power electronics converters, inject
harmonic currents in the AC system and increase overall
reactive power demanded by the equivalent loads are presents
non-linear characteristics. Also, the number of sensitive loads
that require ideal sinusoidal supply voltages for their proper
operation has increased. In order to keep power quality under
limits proposed by standards, it is necessary to include some
sort of compensation. The aim of this paper is to present a
unified power quality conditioner (UPQC) with minimization
of DC Link voltage for the improvement of power quality by
Fuzzy logic controller as compared with PI controller. By the
proposed system is comprised of series and shunt Inverters
which can compensate the sag, swell, unbalance voltage,
Harmonics and reactive power. PI and fuzzy logic controllers
are used to stabilize DC link voltage and balance the active
power between shunt and series inverters for the enhancement
of power quality.
Power system harmonics are a menace to electric power system with disastrous consequence. Due to the presence of non linear load, power quality of the system gets affected. To overcome this, shunt active power filter have been used near harmonic producing loads or at the point of common coupling to block current harmonics. The shunt active power filter is designed to minimize harmonics in source current and reactive power in the non linear power supplies which are creating harmonics. In this paper, Instantaneous power of p-q theory is employed to generate the reference currents and PI controller is used to control the dc link voltage. In addition to this, Artificial Intelligence (AI) technique is used to minimize the harmonics produced by nonlinear load. The main objective of this paper is to analyze and compare THD of the source current with PI controller and by artificial neural network based back propagation algorithm. The proposed system is designed with MATLAB/SIMULINK environment.
In the modern power system the reactive power compensation is one of the main issues, the transmission of active power requires a difference in angular phase between voltages at the sending and receiving points (which is feasible within wide limits), whereas the transmission of reactive power requires a difference in magnitude of these same voltages (which is feasible only within very narrow limits). The reactive power is consumed not only by most of the network elements, but also by most of the consumer loads, so it must be supplied somewhere. If we can't transmit it very easily, then it ought to be generated where it is needed." (Reference Edited by T. J. E. Miller, Forward Page ix).Thus we need to work on the efficient methods by which VAR compensation can be applied easily and we can optimize the modern power system. VAR control technique can provides appropriate placement of compensation devices by which a desirable voltage profile can be achieved and at the same time minimizing the power losses in the system. This report discusses the transmission line requirements for reactive power compensation. In this report thyristor switched capacitor is explained which is a static VAR compensator used for reactive power management in electrical systems.
Seminar Topic For Electrical and Electronics Engineering (EEE)
Performance and High Robustness DPC for PWM Rectifier under Unstable VDC BusIJPEDS-IAES
This paper proposes a strategy de controlling a static AC / DC converter
based on direct power control (DPC). The instantaneous active and reactive
power is controlled in such a way to ensure the PWM rectifier with a
sinusoidal current absorption. This control has proven effective in terms of
reduction of total harmonic distortion (THD) of current absorbed. Offers a
good control of active and reactive power with an operation at unitary power
factor. The test of robustness carried out and the results have proven DPC
good performance with strong possibility of de integrate it into the field of
high voltage and high power as electric traction.
Power System Harmonic Compensation Using Shunt Active Power FilterIJERA Editor
This paper shows the method of improving the power quality using shunt active power filter. The proposedtopic comprises of PI controller, filter hysteresis current control loop, dc link capacitor. The switching signal generation for filter is fromhysteresis current controller techniques. With the all these element shunt active power filter reduce the total harmonic distortion. Thispaper represents the simulation and analysis of the using three phase three wire system active filter to compensate harmonics .Theproposed shunt active filter model uses balanced non-linear load. This paper successfully lowers the THD within IEEE norms and satisfactorily works to compensatecurrent harmonics.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
A Novel Technique for Enhancing Active and Reactive Power Quality for Renewab...IJMER
Renewable energy resources (RES) are being increasingly connected in distribution systems utilizing power electronic converters. This paper presents a novel control strategy for achieving maximum benefits from these grid-interfacing inverters when installed in 3-phase 4-wire distribution systems. The inverter is controlled to perform as a multi-function device by incorporating active power filter functionality. The inverter can thus be utilized as: 1) power converter to inject power generated from RES to the grid, and 2) shunt APF to compensate current unbalance, load current harmonics, load reactive power demand and load neutral current. All of these functions may be accomplished either individually or simultaneously. With such a control, the combination of grid-interfacing inverter and the 3-phase 4-wire linear/non-linear unbalanced load at point of common coupling appears as balanced linear load to the grid. This new control concept is demonstrated with extensive MATLAB/Simulink simulation studies and results.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Power System State Estimation - A ReviewIDES Editor
The aim of this article is to provide a comprehensive
survey on power system state estimation techniques. The
algorithms used for finding the system states under both static
and dynamic state estimations are discussed in brief. The
authors are opinion that the scope of pursuing research in the
area of state estimation with PMU and SCADA measurements
is the state of the art and timely.
Artificial Intelligence Technique based Reactive Power Planning Incorporating...IDES Editor
Reactive Power Planning is a major concern in the
operation and control of power systems This paper compares
the effectiveness of Evolutionary Programming (EP) and
New Improved Differential Evolution (NIMDE) to solve
Reactive Power Planning (RPP) problem incorporating
FACTS Controllers like Static VAR Compensator (SVC),
Thyristor Controlled Series Capacitor (TCSC) and Unified
power flow controller (UPFC) considering voltage stability.
With help of Fast Voltage Stability Index (FVSI), the critical
lines and buses are identified to install the FACTS controllers.
The optimal settings of the control variables of the generator
voltages,transformer tap settings and allocation and parameter
settings of the SVC,TCSC,UPFC are considered for reactive
power planning. The test and Validation of the proposed
algorithm are conducted on IEEE 30–bus system and 72-bus
Indian system.Simulation results shows that the UPFC gives
better results than SVC and TCSC and the FACTS controllers
reduce the system losses.
Design and Performance Analysis of Genetic based PID-PSS with SVC in a Multi-...IDES Editor
Damping of power system oscillations with the help
of proposed optimal Proportional Integral Derivative Power
System Stabilizer (PID-PSS) and Static Var Compensator
(SVC)-based controllers are thoroughly investigated in this
paper. This study presents robust tuning of PID-PSS and
SVC-based controllers using Genetic Algorithms (GA) in
multi machine power systems by considering detailed model
of the generators (model 1.1). The effectiveness of FACTSbased
controllers in general and SVC-based controller in
particular depends upon their proper location. Modal
controllability and observability are used to locate SVC–based
controller. The performance of the proposed controllers is
compared with conventional lead-lag power system stabilizer
(CPSS) and demonstrated on 10 machines, 39 bus New England
test system. Simulation studies show that the proposed genetic
based PID-PSS with SVC based controller provides better
performance.
Optimal Placement of DG for Loss Reduction and Voltage Sag Mitigation in Radi...IDES Editor
This paper presents the need to operate the power
system economically and with optimum levels of voltages has
further led to an increase in interest in Distributed
Generation. In order to reduce the power losses and to improve
the voltage in the distribution system, distributed generators
(DGs) are connected to load bus. To reduce the total power
losses in the system, the most important process is to identify
the proper location for fixing and sizing of DGs. It presents a
new methodology using a new population based meta heuristic
approach namely Artificial Bee Colony algorithm(ABC) for
the placement of Distributed Generators(DG) in the radial
distribution systems to reduce the real power losses and to
improve the voltage profile, voltage sag mitigation. The power
loss reduction is important factor for utility companies because
it is directly proportional to the company benefits in a
competitive electricity market, while reaching the better power
quality standards is too important as it has vital effect on
customer orientation. In this paper an ABC algorithm is
developed to gain these goals all together. In order to evaluate
sag mitigation capability of the proposed algorithm, voltage
in voltage sensitive buses is investigated. An existing 20KV
network has been chosen as test network and results are
compared with the proposed method in the radial distribution
system.
Line Losses in the 14-Bus Power System Network using UPFCIDES Editor
Controlling power flow in modern power systems
can be made more flexible by the use of recent developments
in power electronic and computing control technology. The
Unified Power Flow Controller (UPFC) is a Flexible AC
transmission system (FACTS) device that can control all the
three system variables namely line reactance, magnitude and
phase angle difference of voltage across the line. The UPFC
provides a promising means to control power flow in modern
power systems. Essentially the performance depends on proper
control setting achievable through a power flow analysis
program. This paper presents a reliable method to meet the
requirements by developing a Newton-Raphson based load
flow calculation through which control settings of UPFC can
be determined for the pre-specified power flow between the
lines. The proposed method keeps Newton-Raphson Load Flow
(NRLF) algorithm intact and needs (little modification in the
Jacobian matrix). A MATLAB program has been developed to
calculate the control settings of UPFC and the power flow
between the lines after the load flow is converged. Case studies
have been performed on IEEE 5-bus system and 14-bus system
to show that the proposed method is effective. These studies
indicate that the method maintains the basic NRLF properties
such as fast computational speed, high degree of accuracy and
good convergence rate.
Study of Structural Behaviour of Gravity Dam with Various Features of Gallery...IDES Editor
The size and shape of opening in dam causes the
stress concentration, it also causes the stress variation in the
rest of the dam cross section. The gravity method of the analysis
does not consider the size of opening and the elastic property
of dam material. Thus the objective of study is comprises of
the Finite Element Method which considers the size of
opening, elastic property of material, and stress distribution
because of geometric discontinuity in cross section of dam.
Stress concentration inside the dam increases with the opening
in dam which results in the failure of dam. Hence it is
necessary to analyses large opening inside the dam. By making
the percentage area of opening constant and varying size and
shape of opening the analysis is carried out. For this purpose
a section of Koyna Dam is considered. Dam is defined as a
plane strain element in FEM, based on geometry and loading
condition. Thus this available information specified our path
of approach to carry out 2D plane strain analysis. The results
obtained are then compared mutually to get most efficient
way of providing large opening in the gravity dam.
Assessing Uncertainty of Pushover Analysis to Geometric ModelingIDES Editor
Pushover Analysis a popular tool for seismic
performance evaluation of existing and new structures and is
nonlinear Static procedure where in monotonically increasing
loads are applied to the structure till the structure is unable
to resist the further load .During the analysis, whatever the
strength of concrete and steel is adopted for analysis of
structure may not be the same when real structure is
constructed and the pushover analysis results are very sensitive
to material model adopted, geometric model adopted, location
of plastic hinges and in general to procedure followed by the
analyzer. In this paper attempt has been made to assess
uncertainty in pushover analysis results by considering user
defined hinges and frame modeled as bare frame and frame
with slab modeled as rigid diaphragm and results compared
with experimental observations. Uncertain parameters
considered includes the strength of concrete, strength of steel
and cover to the reinforcement which are randomly generated
and incorporated into the analysis. The results are then
compared with experimental observations.
Secure Multi-Party Negotiation: An Analysis for Electronic Payments in Mobile...IDES Editor
This paper is an attempt to base on auctions which
presents a frame work for the secure multi-party decision
protocols. In addition to the implementations which are very
light weighted, the main focus is on synchronizing security
features for avoiding agreements manipulations and reducing
the user traffic. Through this paper one can understand that
this different auction protocols on top of the frame work can
be collaborated using mobile devices. This paper present the
negotiation between auctioneer and the proffered and this
negotiation shows that multiparty security is far better than
the existing system.
Selfish Node Isolation & Incentivation using Progressive ThresholdsIDES Editor
The problems associated with selfish nodes in
MANET are addressed by a collaborative watchdog approach
which reduces the detection time for selfish nodes thereby
improves the performance and accuracy of watchdogs[1]. In
the related works they make use of credit based systems, reputation
based mechanisms, pathrater and watchdog mechanism
to detect such selfish nodes. In this paper we follow an approach
of collaborative watchdog which reduces the detection
time for selfish nodes and also involves the removal of such
selfish nodes based on some progressively assessed thresholds.
The threshold gives the nodes a chance to stop misbehaving
before it is permanently deleted from the network.
The node passes through several isolation processes before it
is permanently removed. Another version of AODV protocol
is used here which allows the simulation of selfish nodes in
NS2 by adding or modifying log files in the protocol.
Various OSI Layer Attacks and Countermeasure to Enhance the Performance of WS...IDES Editor
Wireless sensor networks are networks having non
wired infrastructure and dynamic topology. In OSI model each
layer is prone to various attacks, which halts the performance
of a network .In this paper several attacks on four layers of
OSI model are discussed and security mechanism is described
to prevent attack in network layer i.e wormhole attack. In
Wormhole attack two or more malicious nodes makes a covert
channel which attracts the traffic towards itself by depicting a
low latency link and then start dropping and replaying packets
in the multi-path route. This paper proposes promiscuous mode
method to detect and isolate the malicious node during
wormhole attack by using Ad-hoc on demand distance vector
routing protocol (AODV) with omnidirectional antenna. The
methodology implemented notifies that the nodes which are
not participating in multi-path routing generates an alarm
message during delay and then detects and isolate the
malicious node from network. We also notice that not only
the same kind of attacks but also the same kind of
countermeasures can appear in multiple layer. For example,
misbehavior detection techniques can be applied to almost all
the layers we discussed.
Responsive Parameter based an AntiWorm Approach to Prevent Wormhole Attack in...IDES Editor
The recent advancements in the wireless technology
and their wide-spread deployment have made remarkable
enhancements in efficiency in the corporate and industrial
and Military sectors The increasing popularity and usage of
wireless technology is creating a need for more secure wireless
Ad hoc networks. This paper aims researched and developed
a new protocol that prevents wormhole attacks on a ad hoc
network. A few existing protocols detect wormhole attacks but
they require highly specialized equipment not found on most
wireless devices. This paper aims to develop a defense against
wormhole attacks as an Anti-worm protocol which is based on
responsive parameters, that does not require as a significant
amount of specialized equipment, trick clock synchronization,
no GPS dependencies.
Cloud Security and Data Integrity with Client Accountability FrameworkIDES Editor
The Cloud based services provide much efficient
and seamless ways for data sharing across the cloud. The fact
that the data owners no longer possess data makes it very
difficult to assure data confidentiality and to enable secure
data sharing in the cloud. Despite of all its advantages this
will remain a major limitation that acts as a barrier to the
wider deployment of cloud based services. One of the possible
ways for ensuring trust in this aspect is the introduction of
accountability feature in the cloud computing scenario. The
Cloud framework requires promotion of distributed
accountability for such dynamic environment[1]. In some
works, there‘s an accountable framework suggested to ensure
distributed accountability for data sharing by the generation
of only a log of data access, but without any embedded feedback
mechanism for owner permission towards data
protection[2].The proposed system is an enhanced client
accountability framework which provides an additional client
side verification for each access towards enhanced security of
data. The integrity of content of data which resides in the
cloud service provider is also maintained by secured
outsourcing. Besides, the authentication of JAR(Java Archive)
files are done to ensure file protection and to maintain a safer
environment for data sharing. The analysis of various
functionalities of the framework depicts both the
accountability and security feature in an efficient manner.
Genetic Algorithm based Layered Detection and Defense of HTTP BotnetIDES Editor
A System state in HTTP botnet uses HTTP protocol
for the creation of chain of Botnets thereby compromising
other systems. By using HTTP protocol and port number 80,
attacks can not only be hidden but also pass through the
firewall without being detected. The DPR based detection
leads to better analysis of botnet attacks [3]. However, it
provides only probabilistic detection of the attacker and also
time consuming and error prone. This paper proposes a Genetic
algorithm based layered approach for detecting as well as
preventing botnet attacks. The paper reviews p2p firewall
implementation which forms the basis of filtering.
Performance evaluation is done based on precision, F-value
and probability. Layered approach reduces the computation
and overall time requirement [7]. Genetic algorithm promises
a low false positive rate.
Enhancing Data Storage Security in Cloud Computing Through SteganographyIDES Editor
in cloud computing data storage is a significant issue
because the entire data reside over a set of interconnected
resource pools that enables the data to be accessed through
virtual machines. It moves the application software’s and
databases to the large data centers where the management of
data is actually done. As the resource pools are situated over
various corners of the world, the management of data and
services may not be fully trustworthy. So, there are various
issues that need to be addressed with respect to the
management of data, service of data, privacy of data, security
of data etc. But the privacy and security of data is highly
challenging. To ensure privacy and security of data-at-rest in
cloud computing, we have proposed an effective and a novel
approach to ensure data security in cloud computing by means
of hiding data within images following is the concept of
steganography. The main objective of this paper is to prevent
data access from cloud data storage centers by unauthorized
users. This scheme perfectly stores data at cloud data storage
centers and retrieves data from it when it is needed.
The main tasks of a Wireless Sensor Network
(WSN) are data collection from its nodes and communication
of this data to the base station (BS). The protocols used for
communication among the WSN nodes and between the WSN
and the BS, must consider the resource constraints of nodes,
battery energy, computational capabilities and memory. The
WSN applications involve unattended operation of the network
over an extended period of time. In order to extend the lifetime
of a WSN, efficient routing protocols need to be adopted. The
proposed low power routing protocol based on tree-based
network structure reliably forwards the measured data towards
the BS using TDMA. An energy consumption analysis of the
WSN making use of this protocol is also carried out. It is
found that the network is energy efficient with an average
duty cycle of 0:7% for the WSN nodes. The OmNET++
simulation platform along with MiXiM framework is made
use of.
Permutation of Pixels within the Shares of Visual Cryptography using KBRP for...IDES Editor
The security of authentication of internet based
co-banking services should not be susceptible to high risks.
The passwords are highly vulnerable to virus attacks due to
the lack of high end embedding of security methods. In order
for the passwords to be more secure, people are generally
compelled to select jumbled up character based passwords
which are not only less memorable but are also equally prone
to insecurity. Multiple use of distributed shares has been
studied to solve the problem of authentication by algorithms
based on thresholding of pixels in image processing and visual
cryptography concepts where the subset of shares is considered
for the recovery of the original image for authentication using
correlation function[1][2].The main disadvantage in the above
study is the plain storage of shares and also one of the shares
is being supplied to the customer, which will lead to the
possibility of misuse by a third party. This paper proposes a
technique for scrambling of pixels by key based random
permutation (KBRP) within the shares before the
authentication has been attempted. Total number of shares to
be created is dependent on the multiplicity of ownership of
the account. By this method the problem of uncertainty among
the customers with regard to security, storage, retrieval of
holding of half of the shares is minimized.
This paper presents a trifocal Rotman Lens Design
approach. The effects of focal ratio and element spacing on
the performance of Rotman Lens are described. A three beam
prototype feeding 4 element antenna array working in L-band
has been simulated using RLD v1.7 software. Simulated
results show that the simulated lens has a return loss of –
12.4dB at 1.8GHz. Beam to array port phase error variation
with change in the focal ratio and element spacing has also
been investigated.
Band Clustering for the Lossless Compression of AVIRIS Hyperspectral ImagesIDES Editor
Hyperspectral images can be efficiently compressed
through a linear predictive model, as for example the one
used in the SLSQ algorithm. In this paper we exploit this
predictive model on the AVIRIS images by individuating,
through an off-line approach, a common subset of bands, which
are not spectrally related with any other bands. These bands
are not useful as prediction reference for the SLSQ 3-D
predictive model and we need to encode them via other
prediction strategies which consider only spatial correlation.
We have obtained this subset by clustering the AVIRIS bands
via the clustering by compression approach. The main result
of this paper is the list of the bands, not related with the
others, for AVIRIS images. The clustering trees obtained for
AVIRIS and the relationship among bands they depict is also
an interesting starting point for future research.
Microelectronic Circuit Analogous to Hydrogen Bonding Network in Active Site ...IDES Editor
A microelectronic circuit of block-elements
functionally analogous to two hydrogen bonding networks is
investigated. The hydrogen bonding networks are extracted
from â-lactamase protein and are formed in its active site.
Each hydrogen bond of the network is described in equivalent
electrical circuit by three or four-terminal block-element.
Each block-element is coded in Matlab. Static and dynamic
analyses are performed. The resultant microelectronic circuit
analogous to the hydrogen bonding network operates as
current mirror, sine pulse source, triangular pulse source as
well as signal modulator.
Texture Unit based Monocular Real-world Scene Classification using SOM and KN...IDES Editor
In this paper a method is proposed to discriminate
real world scenes in to natural and manmade scenes of similar
depth. Global-roughness of a scene image varies as a function
of image-depth. Increase in image depth leads to increase in
roughness in manmade scenes; on the contrary natural scenes
exhibit smooth behavior at higher image depth. This particular
arrangement of pixels in scene structure can be well explained
by local texture information in a pixel and its neighborhood.
Our proposed method analyses local texture information of a
scene image using texture unit matrix. For final classification
we have used both supervised and unsupervised learning using
K-Nearest Neighbor classifier (KNN) and Self Organizing
Map (SOM) respectively. This technique is useful for online
classification due to very less computational complexity.
State of ICS and IoT Cyber Threat Landscape Report 2024 previewPrayukth K V
The IoT and OT threat landscape report has been prepared by the Threat Research Team at Sectrio using data from Sectrio, cyber threat intelligence farming facilities spread across over 85 cities around the world. In addition, Sectrio also runs AI-based advanced threat and payload engagement facilities that serve as sinks to attract and engage sophisticated threat actors, and newer malware including new variants and latent threats that are at an earlier stage of development.
The latest edition of the OT/ICS and IoT security Threat Landscape Report 2024 also covers:
State of global ICS asset and network exposure
Sectoral targets and attacks as well as the cost of ransom
Global APT activity, AI usage, actor and tactic profiles, and implications
Rise in volumes of AI-powered cyberattacks
Major cyber events in 2024
Malware and malicious payload trends
Cyberattack types and targets
Vulnerability exploit attempts on CVEs
Attacks on counties – USA
Expansion of bot farms – how, where, and why
In-depth analysis of the cyber threat landscape across North America, South America, Europe, APAC, and the Middle East
Why are attacks on smart factories rising?
Cyber risk predictions
Axis of attacks – Europe
Systemic attacks in the Middle East
Download the full report from here:
https://sectrio.com/resources/ot-threat-landscape-reports/sectrio-releases-ot-ics-and-iot-security-threat-landscape-report-2024/
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Builder.ai Founder Sachin Dev Duggal's Strategic Approach to Create an Innova...Ramesh Iyer
In today's fast-changing business world, Companies that adapt and embrace new ideas often need help to keep up with the competition. However, fostering a culture of innovation takes much work. It takes vision, leadership and willingness to take risks in the right proportion. Sachin Dev Duggal, co-founder of Builder.ai, has perfected the art of this balance, creating a company culture where creativity and growth are nurtured at each stage.
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Neuro-symbolic is not enough, we need neuro-*semantic*Frank van Harmelen
Neuro-symbolic (NeSy) AI is on the rise. However, simply machine learning on just any symbolic structure is not sufficient to really harvest the gains of NeSy. These will only be gained when the symbolic structures have an actual semantics. I give an operational definition of semantics as “predictable inference”.
All of this illustrated with link prediction over knowledge graphs, but the argument is general.
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
Elevating Tactical DDD Patterns Through Object CalisthenicsDorra BARTAGUIZ
After immersing yourself in the blue book and its red counterpart, attending DDD-focused conferences, and applying tactical patterns, you're left with a crucial question: How do I ensure my design is effective? Tactical patterns within Domain-Driven Design (DDD) serve as guiding principles for creating clear and manageable domain models. However, achieving success with these patterns requires additional guidance. Interestingly, we've observed that a set of constraints initially designed for training purposes remarkably aligns with effective pattern implementation, offering a more ‘mechanical’ approach. Let's explore together how Object Calisthenics can elevate the design of your tactical DDD patterns, offering concrete help for those venturing into DDD for the first time!
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
Dev Dives: Train smarter, not harder – active learning and UiPath LLMs for do...UiPathCommunity
💥 Speed, accuracy, and scaling – discover the superpowers of GenAI in action with UiPath Document Understanding and Communications Mining™:
See how to accelerate model training and optimize model performance with active learning
Learn about the latest enhancements to out-of-the-box document processing – with little to no training required
Get an exclusive demo of the new family of UiPath LLMs – GenAI models specialized for processing different types of documents and messages
This is a hands-on session specifically designed for automation developers and AI enthusiasts seeking to enhance their knowledge in leveraging the latest intelligent document processing capabilities offered by UiPath.
Speakers:
👨🏫 Andras Palfi, Senior Product Manager, UiPath
👩🏫 Lenka Dulovicova, Product Program Manager, UiPath
Securing your Kubernetes cluster_ a step-by-step guide to success !KatiaHIMEUR1
Today, after several years of existence, an extremely active community and an ultra-dynamic ecosystem, Kubernetes has established itself as the de facto standard in container orchestration. Thanks to a wide range of managed services, it has never been so easy to set up a ready-to-use Kubernetes cluster.
However, this ease of use means that the subject of security in Kubernetes is often left for later, or even neglected. This exposes companies to significant risks.
In this talk, I'll show you step-by-step how to secure your Kubernetes cluster for greater peace of mind and reliability.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.