The document is a seminar report on the Multi Air engine technology developed by Fiat. It discusses the history and development of Multi Air, how the technology works, the advantages it provides over existing variable valve timing systems such as reduced fuel consumption and emissions. The technology allows independent control of intake valves on a cylinder-by-cylinder basis to optimize air flow. The first engines to use Multi Air will be Fiat's 1.4L and new 900cc two-cylinder engines.
A six stroke engine describes a number of different approaches in the internal combustion engine to capture the waste heat from the four stroke Otto cycle and use it to power an additional power and exhaust stroke of the piston.
A six stroke engine describes a number of different approaches in the internal combustion engine to capture the waste heat from the four stroke Otto cycle and use it to power an additional power and exhaust stroke of the piston.
Since the invention of internal combustion engines, camshafts have been used to operate the valves on the cylinder head to bring in air and fuel and expel exhaust gases. The conventional valve train has its limitations: the single lobed cam is designed to operate the valves at only specific periods of the Otto cycle, thus preventing the engine from achieving maximum torque at higher rpms. The opening and closing of the valves is constrained by the geometry of the cam profile. The concept of camless engines allows for greater optimization of overall engine performance during different phases of running.
Since the invention of internal combustion engines, camshafts have been used to operate the valves on the cylinder head to bring in air and fuel and expel exhaust gases. The conventional valve train has its limitations: the single lobed cam is designed to operate the valves at only specific periods of the Otto cycle, thus preventing the engine from achieving maximum torque at higher rpms. The opening and closing of the valves is constrained by the geometry of the cam profile. The concept of camless engines allows for greater optimization of overall engine performance during different phases of running.
If you want to know information about electromagnetic clutch manufacturers then Web portal of tradeindia provide the best listing of manufacturers,suppliers and Exporters of electromagnetic clutch.
CYLINDER DEACTIVATION ON TWO DIFFERENT CUBIC CAPACITY ENGINEIAEME Publication
Cylinder deactivation is a fuel consumption reduction technology for throttled internal combustion engines and other engines with thermal efficiency loss at part cylinder. Dynamic skip firing, which in its ultimate form incorporates anytime, any-cylinder deactivation, continuously varies the number of firing cylinders, along with cylinder load, obtaining flexible control of acoustic and vibrational excitations from the engine, and allowing an expanded operational envelope with fewer drive ability/NVH issues. This project comprises of two different cubic capacity 4 stroke (150cc-pulsar and 100cc-kinetic) engines coupled with use of sprockets and chains.
Rack And Pinion Mechanism for Continuous Variable Valve Timing of IC EnginesIJERA Editor
The valve timing is a very closely studied event and effects the performance of an IC Engine greatly with
respect to the Brake Power Produced, Volumetric Efficiency and Emissions etc. The valve event if varied and
experimented with, can result in higher efficiencies and overall improved performance of the Engine. Hence,
various researchers have attempted to temper with the valve timing and thus many Variable Valve Timing
systems have been proposed till date with many of them being implemented by various manufacturers.
However, on reviewing the presently employed systems, the lack of existence of a single system capable of
independently altering both the timing and the lift of the valves was recognized. Thus, a single system capable
of achieving the above was thought of and designed. A rack and pinion mechanism powered by a programmed
servo motor mounted vertically seemed most practical in achieving this within the size and space constraints. A
single cylinder diesel Engine was simulated with „Lotus Engine Simulation‟ software to derive the optimum
valve angles and lifts for a range of the Engine operating speed and the system was accordingly programmed
and designed to achieve them. The system was designed in „Creo‟ software and analysed correspondingly in
„Ansys‟ software and then finally assembled on a Diesel Engine in the lab.
The Automobile Industry and the many other various engine
manufacturers need improved engine performance in keeping up with the necessary changes to protect our wallets and environment. Both the Automobile and Engine Industries are now struggling to comply with Government requirements and are falling behind in keeping up with proposed future regulations and Government mandates that will provide the necessary advancement to protect us and the Earth’s environment. The Automotive Industry has requested that the US Government reduce the fuel economy and emission requirements for future vehicles because, by their own admission, they do not have the technology to meet such fuel
economy and pollution mandates for the foreseeable future. Yoke arm has changed all of this
it is a ppt on koenigsegg camless valves which are new inventions in ic engine here its principle and working have been explaned.and also working of conventional engine habe been explained.
Solid-State Thermal Management and Energy Harvesting JASIM ASHRAF
Solid-state thermoelectric devices use multiple semiconductor couples sandwiched between two ceramic plates. These couples are usually connected electrically in series. These devices are powered by electrical current. Electrical current "pumps" heat from one side of the device to the other. This creates a hot side and a cold side. The heat flow is reversible by reversing the direction of electrical current. The magnitude of heat flow is adjustable by varying the amount of electrical current.
The Green Engine Co was a British engine company founded by Gustavus Green in Bexhill to sell engines of his design. He flourished especially as a designer of aeroplane engines during the first two decades of the 20th century. The engines were actually manufactured by the Aster Engineering Company.
1. SEMINAR REPORT MULTI AIR ENGINE
A
Seminar Report
ON
“ MULTI AIR ENGINE ”
Submitted in partial fulfillment of the requirements
Of the Degree of
Bachelor of Technology in Mechanical Engg. Of
Rajasthan Technical University, Kota
(2015-2016)
Submitted to Submitted by
AMAR CHAND CHAUDHARY JASIM ASHRAF
SEMINAR COORDINATOR(ME) (12EJEME046
2. SEMINAR REPORT MULTI AIR ENGINE
STUDENT’S DECLARATION
I hereby, which is being presented in the Seminar Report, entitled “MULTI AIR
ENGINE” in partial fulfillment of the requirement for the award of Degree of B.Tech in
Mechanical Engineering, submitted in the Department of Mechanical Engineering of
JAIPUR ENGINEERING COLLEGE, KUKAS, Affiliated to Rajasthan Technical
University (RTU), Kota, Rajasthan, is an authentic record of my work under the
supervision of Mr.Amar C. Chaudhary.
The results embodied in this report have not been submitted by me or any body
else to any other University or Institute for the award of Degree.
JASIM ASHRAF
12EJEME046
CERTIFICATE
This is to certify that the above statement made by the Student is correct to the best of our
knowledge.
Mr.Amar Chand Chaudhary Mrs. Pinky
Mouriya
Seminar Co-ordinator HOD, ME
3. SEMINAR REPORT MULTI AIR ENGINE
)
DEPARTMENT OF MECHANICAL ENGINEERING
JAIPUR ENGINEERING COLLEGE, KUKAS, JAIPUR
(RAJASTHAN)
RAJASTHAN TECHNICAL UNIVERSITY, KOTA
4. SEMINAR REPORT MULTI AIR ENGINE
MULTI AIR ENGINE
INDEX
1.1.Abstract
2.1.Introduction
3.1.history and other systems
4.1.Development of the fait multi air system
5.1.Multi air technology
6.1.Futher potential of multi air technology
7.1.Difference between multi air and existing variable valve timing systems
8.1.Multi air technology advantages
9.1.Conclusion
10.1.References
5. SEMINAR REPORT MULTI AIR ENGINE
1.INTRODUCTION
Fiat Group was one of the first
manufacturers to adopt what has become the increasingly common practice
of improving official fuel economy and CO2 emissions by creating a small
forced-induction engine which uses fuel at a modest rate when the
turbocharger isn't operating but produces similar power to a much larger unit
when it is. In 2010, it has taken the idea a stage further by introducing
various versions the 1.4-litre MultiAir petrol engine to the Punto Evo and Alfa
Romeo MiTo ranges.
In the Geneva Auto Show to launch a new engine technology which could
ultimately be as important as the common rail diesel technology it invented
15 years ago. Dubbed MultiAir, the hydraulically-actuated variable valve
timing (VVT) technology was first announced as a concept two years ago,
and offers a more controllable flow of air during the combustion cycle in
comparison with mechanical VVT systems. Vastly reduced fuel consumption
and emmissions plus significantly more power are claimed, and the
technology is even more effective when used with a supercharger or a diesel
engine.
Fiat claims Multiair is a fundamental breakthrough in petrol engine design
that will dramatically cut fuel consumption, as well as significantly boosting
power and torque, cutting carbon dioxide emissions by between 10 and 25
percent, and up to a 60 percent reduction in other engine pollutants.
This higher output will allow Fiat to replace larger engines with smaller, more
efficient ones, and the company's 1.0 liter and 1.4 liter engines will be the
first to get the new technology, along with a new 900cc twin cylinder engine.
Unlike the common rail diesel technology, which it sold to Bosch during a
financial crisis, and has regreted ever since, FIAT will not be relinquishing
ownership of the new Multiair system, having announced it will license it to
other manufacturers or provide entire engines.
6. SEMINAR REPORT MULTI AIR ENGINE
History
The Multiair technology took over a decade to get finished. The vice
president of Fiat Powertrain Research & Development Rinaldo Rinolfi led the
team who developed the technology. Development costs were over $100
million. There was also delay in development, in the time (2000-2005) when
Fiat was in partnership with General Motors.
Other systems
Currently ready alternatives to industrialization do not exist, but there
are under development also totally camless systems. The Valvetronic
system used by BMW allows the valve timing and lift to be varied but not the
cam profile. The ability to vary the latter is characteristic of camless and the
Multiair systems.
7. SEMINAR REPORT MULTI AIR ENGINE
Development of the Fiat MultiAir system
In the last decade, the development of Common Rail technology for
diesel engines marked a breakthrough in the passenger car market. To be
equally competitive in the field of petrol engines, Fiat Group decided to follow
the same approach and focus on breakthrough technologies.
The aim was to provide customers with substantial benefits in terms of fuel
economy and driving pleasure, while maintaining the engine’s intrinsic
refinement, based on a smooth combustion process and on light structures
and components.
The key parameter to control diesel engine combustion and therefore
performance, emissions and fuel consumption, is the quantity and
characteristics of the fuel injected into the cylinders. That is the reason why
the Common Rail electronic diesel fuel injection system was such a
fundamental breakthrough in direct injection diesel engine technology.
However, the key to controlling petrol engine combustion, and therefore
performance, emissions and fuel consumption is the quantity and
characteristics of the fresh air charge in the cylinders. In conventional petrol
engines the air mass trapped in the cylinders is controlled by keeping the
intake valve opening constant and adjusting upstream pressure through a
throttle valve. One of the drawbacks of this simple conventional mechanical
control is that the engine wastes about 10 per cent of the input energy in
pumping the air charge from a lower intake pressure to the atmospheric
exhaust pressure.
A fundamental breakthrough in air mass control, and therefore in petrol
engine technology, is based on direct air charge metering at the cylinder inlet
ports by means of advanced electronic actuation and control of the intake
valves, while maintaining a constant natural upstream pressure.
Research on this key technology started in the ’80s, when engine electronic
control reached the stage of a mature technology.
At the outset, world-wide research efforts were focused on the
electromagnetic actuation concept, by which valve opening and closing is
obtained by alternatively energising upper and lower magnets with an
8. SEMINAR REPORT MULTI AIR ENGINE
armature connected to the valve. This actuating principle had the intrinsic
appeal of maximum flexibility and dynamic response in valve control, but
despite a decade of significant development efforts, the main drawbacks of
the concept – it being intrinsically not fail-safe and its high energy absorption
– could not be fully overcome.
At this point most automotive companies fell back on the development of the
simpler, robust and well-known electromechanical concepts, based on valve
lift variation through dedicated mechanisms, usually combined with camshaft
phasers to allow control of both valve lift and phase.
The main limitation of these systems is low flexibility in valve opening
schedules and a much lower dynamic response; for example, all the
cylinders of an engine bank are actuated simultaneously, thereby excluding
any cylinder selective actions. Many similar electromechanical valve control
systems were subsequently introduced over the past decade.
In the mid ’90s, Fiat Group research efforts switched to electro-hydraulic
actuation, leveraging on the know-how gained during its Common Rail
development. The goal was to reach the desired flexibility of valve opening
schedule air mass control on a cylinder-by-cylinder and stroke-by-stroke
basis.
The electro-hydraulic variable valve actuation technology developed by Fiat
was selected for its relative simplicity, low power requirements, intrinsic fail-
safe nature and low cost potential.
MultiAir Technology: how it works
9. SEMINAR REPORT MULTI AIR ENGINE
The operating principle of the system, applied to intake valves, is the
following: a piston, moved by a mechanical intake camshaft, is connected to
the intake valve through a hydraulic chamber, which is controlled by a
normally open on/off solenoid valve.
When the solenoid valve is closed, the oil in the hydraulic chamber behaves
like a solid body and transmits to the intake valves the lift schedule imposed
by the mechanical intake camshaft.
When the solenoid valve is open, the hydraulic chamber and the intake
valves are de-coupled; the intake valves do not follow the intake camshaft
anymore and close under the valve spring action.
The final part of the valve closing stroke is controlled by a dedicated
hydraulic brake, to ensure a soft and regular landing phase in any engine
operating conditions.
Through solenoid valve opening and closing time control, a wide range of
optimum intake valve opening schedules can be easily obtained.
For maximum power, the solenoid valve is always closed and full valve
opening is achieved following completely the mechanical camshaft, which is
specifically designed to maximise power at high engine speed (long opening
time).
For low-rpm torque, the solenoid valve is opened near the end of the
camshaft profile, leading to early intake valve closing. This eliminates
unwanted backflow into the manifold and maximises the air mass trapped in
the cylinders. In engine part-load, the solenoid valve is opened earlier,
10. SEMINAR REPORT MULTI AIR ENGINE
causing partial valve openings to control the trapped air mass as a function
of the required torque.
Alternatively the intake valves can be partially opened by closing the
solenoid valve once the mechanical camshaft action has already started. In
this case the air stream into the cylinder is faster and results in higher in-
cylinder turbulence.
The last two actuation modes can be combined in the same intake stroke,
generating a so-called Multilift mode that enhances turbulence and
combustion rate at very low loads.
Further Potential of MultiAir Technology
All breakthrough technologies open a new world of further potential
benefits, which are usually not fully exploited in the first generation.
11. SEMINAR REPORT MULTI AIR ENGINE
Common Rail technology, a Fiat Group worldwide premiere in 1997, paved
the way to more than a decade of further technological evolutions such as
MultiJet for multiple injections, small diesel engines, and the recent Modular
Injection technology, soon to be launched on the market.
Similarly, MultiAir technology will pave the way to further technological
evolutions for petrol engines:
Integration of the MultiAir Direct air mass control with direct petrol Injection to
further improve transient response and fuel economy. Introduction of more
advanced multiple valve opening strategies to further reduce emissions.
Innovative engine-turbocharger matching to control trapped air mass through
a combination of optimum boost pressure and valve opening strategies.
While electronic petrol injection developed in the ’70s and Common Rail
developed in the ’90s were fuel-specific breakthrough technologies, MultiAir
Electronic Valve Control technology can be applied to all internal combustion
engines whatever fuel they burn.
MultiAir, initially developed for spark ignition engines burning light fuel
ranging from petrol to natural gas and hydrogen, also has wide potential for
diesel engine emissions reduction.
Intrinsic NOx reduction of up to 60 per cent can be obtained by internal
exhaust gas recirculation (iEGR) realised with intake valves reopening during
the exhaust stroke, while optimal valve control strategies during cold start
and warm-up bring up to 40 per cent HC and CO reduction of emissions.
Further substantial reductions come from the more efficient management
and regeneration of the diesel particulate filter and NOx storage catalyst,
thanks to the highly dynamic air mass flow control during transient engine
operation.
Diesel engine performance improvement is similar to that of the petrol engine
and is based on the same physical principles. Instead, fuel consumption
benefits are limited to few percentage points because of the low pumping
losses of diesel engines, one of the reasons for their superior fuel economy.
In the future, powertrain technical evolution might benefit from a progressive
unification of petrol and diesel engine designs.
12. SEMINAR REPORT MULTI AIR ENGINE
A MultiAir engine cylinder head can therefore be conceived and developed,
where both combustion systems can be fully optimised without compromise.
The MultiAir electro-hydraulic actuator is physically the same, with minor
machining differences, while internal sub-components are all carried over
from Fiat’s FIRE and SGE applications.
Difference between MultiAir and existing variable
valve timing (VVT) systems
Current VVT systems rely on mechanical systems to open and close the
valves. Engineers have long understood the benefits of changing valve
opening and closing times to tweak an engine's power and emissions
performance, depending on the need for power or parsimony.
Valves are an engine's nose and mouth – it inhales through inlet valves and
exhales through exhaust valves. Sounds simple enough, but actually
13. SEMINAR REPORT MULTI AIR ENGINE
engines are a lot like people. Depending on what they're doing, they need to
breathe more or less air and the timing and rate of their breathing needs to
vary. Like competitive swimmers who time their breathing to match the
stroke, an engine wants to take long deep breaths when it's working hard
and short shallow ones when it isn't.
Trouble is, it can't. The ancient method of opening and closing valve, the
camshaft, is still in use today because it's simple to make, robust and very
effective. Each valve is opened by a rotating cam on the camshaft whose
shape and size controls how the valve opens and shuts and when it does so.
The valve is closed by a simple spring because, in 100 years, no-one's found
a better tool for the job. But what's right for developing high power at high
rpm isn't right for that torquey, low-speed slog around town and greater
variability of valve opening and closing helps reduce consumption and CO2
emissions too.
A lot of modern engines try to overcome the inadequacies of the traditional
valvetrain with phasers to vary the timing of when valves open and shut.
They may also have cam profile switching (like the Honda VTEC system),
which switches to a hotter cam profile at higher revs. But the effect is limited.
If the engine were a swimmer, it would still be gagging to get the right
amount of air at exactly the right time, like when its face was under water.
The MultiAir system replaces the twin camshafts of a four-valves-per-cylinder
engine. It's so cleverly designed, not only can it be incorporated in new
engines, it fits exsiting motors too – so potentially all sorts of engines (not
just Fiat's) could use it. The single camshaft opens up all four valves.
Exhaust valves are not variable and are opened in the usual way by
mechanical cam lobes. But between the inlet cam lobes and inlet valves are
hydraulic chambers from which oil can be released by electronic solenoid
valves.
14. SEMINAR REPORT MULTI AIR ENGINE
MultiAir Technology benefits
Maximum power is increased by up to 10 per cent thanks to the
adoption of a power-orientated mechanical camshaft profile. Low RPM
torque is improved by up to 15 per cent through early intake valve closing
strategies that maximise the air mass trapped in the cylinders. Elimination of
pumping losses brings a 10 per cent reduction in fuel consumption and CO2
emissions, both in naturally aspirated and turbocharged engines with the
same displacement. MultiAir turbocharged and downsized engines can
achieve up to 25 per cent fuel economy improvement over conventional
naturally aspirated engines with the same level of performance. Optimum
15. SEMINAR REPORT MULTI AIR ENGINE
valve control strategies during engine warm-up and internal exhaust gas
recirculation, realised by reopening the intake valves during the exhaust
stroke, result in emissions reductions ranging from 40 per cent for unburnt
hydrocarbons and carbon monoxide (HC/CO), and up to a 60 per cent cut in
oxides of nitrogen, (NOx). Constant upstream air pressure, atmospheric for
naturally aspirated and higher for turbocharged engines, together with
extremely fast air mass control, cylinder-by-cylinder and stroke-by-stroke,
result in a superior dynamic engine response, and enhanced driving
pleasure. MultiAir is applicable to all internal combustion engines, regardless
of the fuel used. It can be adapted for diesel engines to reduce their NOx
emissions and make particulate filters significantly more effective.
16. SEMINAR REPORT MULTI AIR ENGINE
Conclusion
In short, an engine equipped with Fiat MultiAir technology is more powerful,
more responsive across the entire engine speed range, uses considerably
less fuel, and reduces all types of exhaust emissions by a substantial
amount. It will also assist in enabling Fiat to maintain its lead in low
17. SEMINAR REPORT MULTI AIR ENGINE
emissions and low fuel consumption technology, which has seen Fiat
crowned for the past two years as the number one car maker for the lowest
range-wide CO2 emissions.
The first new engine to be equipped with MultiAir will be the 16-valve 1.4 litre
family of naturally aspirated and turbocharged engines, and the first car to go
on sale with MultiAir installed will be the Alfa MiTo at the end of 2009. Its
second application will be as an integral part of a new two cylinder engine
family.
REFERENCES
1. WWW.GOOGLE.COM
2. WWW.WICKYPEDIA.COM
3. WWW.HOWSTUFFWORKERS.COM
4. WWW.FIAT.IN
18. SEMINAR REPORT MULTI AIR ENGINE
THANK YOU
BY JASIM ASHRAF
Jasimasaraf786@gmail.com