This document summarizes a study on determining the formability index of sheet metals through finite element analysis of the Erichsan cupping test. The formability index is expressed as the Erichsan number (cup height at fracture) and peak load. The study analyzed aluminum alloy, mild steel, brass, and titanium alloy using the Erichsan cupping test setup. The results found the brass had the highest Erichsan number while the titanium alloy had the highest peak load, indicating their relative formability. The formability index provides a way to select appropriate sheet metals for a given component based on their capability to stretch before fracture.
A REVIEW ON OPTIMIZATION OF RESISTANCE SPOT WELDING OF ALUMINUM COMPONENTS US...AM Publications
Resistance Spot welding (RSW) is one of the common welding processes used for sheet joining especially in the automobile and aerospace industry. It is used in a wide range of industries but notably for the assembly of sheet steel vehicle bodies. This is a type of resistance welding where the spot welds are made at regular intervals on overlapping sheets of metal. Spot welding is primarily used for joining parts that are normally up to 3 mm in thickness. The joint quality can be defined in terms of properties such as weld-bead geometry, mechanical properties and distortion.The objective of the research is to determine the optimum combination of parameters responsible for better quality of joints. The complicated behavior of the process must be analyzed to set the optimum parameters to get the optimum weld quality. The paper also presents the FEA simulation of the RSW process.
Studies on jet penetration and kerf width at various operating pressure in ma...eSAT Journals
Abstract Abrasive Water Jet (AWJ) machining is one of the non-traditional machining method popular method for machining of hard, heat sensitive and brittle materials. The present work attempts to investigate the effect of operating pressure on depth of penetration and kerf characteristics generated while machining of D2 heat treated steel. It is found that increase in operating pressure increases the depth of penetration and decreases the surface taper on the work-piece. Keywords: Kerf width, Depth of cut, Operating pressure, AWJ Machining
The big challenge of the mass production firms is concentrated for achieving high quality
products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning
process parameters on hard EN 31 material, for optimization of surface roughness, material removal
rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out
by considering four controllable input variables namely cutting speed, feed rate, depth of cut and
insert nose radius in the presence of wet & MQL system. This experiment also present the relation
between chip formations and controllable variables along with chip thickness, chip colors & chip
velocity from which its effect on insert wear, quality of product can be easily found out, because of
chip morphology gives indirectly the effect of it on the insert wear. In this dissertation work
minimum quantity lubrication system is used for reducing the cutting zone temperature properly and
very fastly. Finally comparison is carried out between wet and minimum quantity lubrication system
from which one can easily identify which system is better for higher productivity along with high
surface finish. This work also present the productivity (MRR) concept in production. The design of
experiment and optimization of surface roughness, material removal rate, machining time is carried
out by using response surface methodology (RSM). Central composite design method is used (CCD)
for the total experimental design work and its analysis and also for optimization of turning process
parameter by which wastage of the machining time, power can be avoided.
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of SAE52100 steel. Carbide inserts were used for machining of SAE 52100 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) & material removal rate of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality
products with increased productivity.
Friction Stir Welding of Similar Metals by Taguchi Optimization Technique -A ...IJAEMSJORNAL
In order to meet the global competition and the survival of products in the market a new way of thinking is necessary to change and improve the existing technology and to develop products at economical price.This paper discusses use taguchi experiment design technique for maximizing tensile strength of friction stir welding AA6061 and AA6061. In friction stir welding, the joints are formed in the solid state by utilizing the heat generated by friction. The objectives of this study are obtaining friction weld element of aluminium 6061 to aluminium 6061 and optimising the friction stir welding parameters in order to establish the weld quality. Effect of tensile strength of friction stir welding process parameter (Rotational speed, travel speed, axial force and tilt angle) is evaluated and optimum welding condition for maximum tensile strength is determined.
A REVIEW ON OPTIMIZATION OF RESISTANCE SPOT WELDING OF ALUMINUM COMPONENTS US...AM Publications
Resistance Spot welding (RSW) is one of the common welding processes used for sheet joining especially in the automobile and aerospace industry. It is used in a wide range of industries but notably for the assembly of sheet steel vehicle bodies. This is a type of resistance welding where the spot welds are made at regular intervals on overlapping sheets of metal. Spot welding is primarily used for joining parts that are normally up to 3 mm in thickness. The joint quality can be defined in terms of properties such as weld-bead geometry, mechanical properties and distortion.The objective of the research is to determine the optimum combination of parameters responsible for better quality of joints. The complicated behavior of the process must be analyzed to set the optimum parameters to get the optimum weld quality. The paper also presents the FEA simulation of the RSW process.
Studies on jet penetration and kerf width at various operating pressure in ma...eSAT Journals
Abstract Abrasive Water Jet (AWJ) machining is one of the non-traditional machining method popular method for machining of hard, heat sensitive and brittle materials. The present work attempts to investigate the effect of operating pressure on depth of penetration and kerf characteristics generated while machining of D2 heat treated steel. It is found that increase in operating pressure increases the depth of penetration and decreases the surface taper on the work-piece. Keywords: Kerf width, Depth of cut, Operating pressure, AWJ Machining
The big challenge of the mass production firms is concentrated for achieving high quality
products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning
process parameters on hard EN 31 material, for optimization of surface roughness, material removal
rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out
by considering four controllable input variables namely cutting speed, feed rate, depth of cut and
insert nose radius in the presence of wet & MQL system. This experiment also present the relation
between chip formations and controllable variables along with chip thickness, chip colors & chip
velocity from which its effect on insert wear, quality of product can be easily found out, because of
chip morphology gives indirectly the effect of it on the insert wear. In this dissertation work
minimum quantity lubrication system is used for reducing the cutting zone temperature properly and
very fastly. Finally comparison is carried out between wet and minimum quantity lubrication system
from which one can easily identify which system is better for higher productivity along with high
surface finish. This work also present the productivity (MRR) concept in production. The design of
experiment and optimization of surface roughness, material removal rate, machining time is carried
out by using response surface methodology (RSM). Central composite design method is used (CCD)
for the total experimental design work and its analysis and also for optimization of turning process
parameter by which wastage of the machining time, power can be avoided.
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of SAE52100 steel. Carbide inserts were used for machining of SAE 52100 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) & material removal rate of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality
products with increased productivity.
Friction Stir Welding of Similar Metals by Taguchi Optimization Technique -A ...IJAEMSJORNAL
In order to meet the global competition and the survival of products in the market a new way of thinking is necessary to change and improve the existing technology and to develop products at economical price.This paper discusses use taguchi experiment design technique for maximizing tensile strength of friction stir welding AA6061 and AA6061. In friction stir welding, the joints are formed in the solid state by utilizing the heat generated by friction. The objectives of this study are obtaining friction weld element of aluminium 6061 to aluminium 6061 and optimising the friction stir welding parameters in order to establish the weld quality. Effect of tensile strength of friction stir welding process parameter (Rotational speed, travel speed, axial force and tilt angle) is evaluated and optimum welding condition for maximum tensile strength is determined.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Analysis of process parameters in dry machining of en 31 steel by grey relati...IAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of EN-31 steel.Carbide inserts were used for machining of EN-31 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality products with increased productivity.Paper presentswork of an investigation of turning process parameters on EN-31 material, for optimization of surface roughness, material removal rate.The experiment is carried out by considering three controllable input variables namely cutting speed, feed rate, and depth of cut.The design of experiment and optimization of surface roughness is carried out by using Taguchi L9 orthogonal array & Grey Relational analysis.
Effectiveness of multilayer coated tool in turning of aisi 430 f steeleSAT Journals
Abstract This paper presents minimization of surface roughness in dry turning of AISI 430F steel using TiN-TiCN-Al2O3-ZrCN multilayer coated cemented carbide & cryo-treated inserts. Effect of cutting velocity, feed rate, depth of cut & machining duration is studied on the surface roughness. Taguchi’s design of experiment is used to find the optimum factor levels. It is found that the feed rate has much effect in producing lower surface roughness followed by speed. The depth of cut has lesser role on surface roughness. The result of Taguchi method shows that cutting velocity of 250m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm should be maintained as optimal parameter settings for both coated and cryo-treated tools. Cryo-treated tools perform better. Keywords: Cryo-treatment, Dry Turning, Surface roughness, Taguchi Method
Regression analysis of shot peening process for performance characteristics o...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Analysis of process parameters in dry machining of en 31 steel by grey relati...IAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of EN-31 steel.Carbide inserts were used for machining of EN-31 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality products with increased productivity.Paper presentswork of an investigation of turning process parameters on EN-31 material, for optimization of surface roughness, material removal rate.The experiment is carried out by considering three controllable input variables namely cutting speed, feed rate, and depth of cut.The design of experiment and optimization of surface roughness is carried out by using Taguchi L9 orthogonal array & Grey Relational analysis.
Effectiveness of multilayer coated tool in turning of aisi 430 f steeleSAT Journals
Abstract This paper presents minimization of surface roughness in dry turning of AISI 430F steel using TiN-TiCN-Al2O3-ZrCN multilayer coated cemented carbide & cryo-treated inserts. Effect of cutting velocity, feed rate, depth of cut & machining duration is studied on the surface roughness. Taguchi’s design of experiment is used to find the optimum factor levels. It is found that the feed rate has much effect in producing lower surface roughness followed by speed. The depth of cut has lesser role on surface roughness. The result of Taguchi method shows that cutting velocity of 250m/min, feed rate of 0.25 mm/rev and depth of cut of 0.3mm should be maintained as optimal parameter settings for both coated and cryo-treated tools. Cryo-treated tools perform better. Keywords: Cryo-treatment, Dry Turning, Surface roughness, Taguchi Method
Regression analysis of shot peening process for performance characteristics o...IJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.