EXPERIMENTAL STUDY OF TURNING OPERATION AND OPTIMIZATION OF MRR AND SURFACE R...AM Publications
In this research work turning operation is performed on AISI 1020 mild steel. Here we conducted experiments by taking Cutting Speed, Feed Rate & Depth of cut as process parameters and got the optimized value of MRR & SR. An L9 orthogonal array, the signal-to-noise (S/N) ratio are employed to the study the performance characteristics in the turning using WNMG332RP carbide insert with a nose radius of 0.8mm. Taguchi method is used to optimize surface roughness and material removal rate (MRR) during machining operation on CNC turning. The experimental result shows that on increasing depth of cut and feed the combined S/N ratio increases while on increasing cutting speed the combined S/N ratio decreases. It results that cutting speed is most significantly influences the Surface roughness followed by feed and in case of MRR, depth of cut is the most significant parameter followed by cutting speed .While the combination of both is most significantly affected by the depth of cut followed by the feed.
Content Comparative Investigation on Tool Wear During End Milling of AISI H13...journalBEEI
Tool wear prediction plays a significant role in machining industry for proper planning and control machining parameters and optimization of cutting conditions. This paper aims to investigate the effect of tool path strategies that are contour-in and zigzag tool path strategies applied on tool wear during pocket milling process. The experiments were carried out on CNC vertical machining centre by involving PVD coated carbide inserts. Cutting speed, feed rate and depth of cut were set to vary. In an experiment with three factors at three levels, Response Surface Method (RSM) design of experiment with a standard called Central Composite Design (CCD) was employed. Results obtained indicate that tool wear increases significantly at higher range of feed per tooth compared to cutting speed and depth of cut. This result of this experimental work is then proven statistically by developing empirical model. The prediction model for the response variable of tool wear for contour-in strategy developed in this research shows a good agreement with experimental work.
EXPERIMENTAL STUDY OF TURNING OPERATION AND OPTIMIZATION OF MRR AND SURFACE R...AM Publications
In this research work turning operation is performed on AISI 1020 mild steel. Here we conducted experiments by taking Cutting Speed, Feed Rate & Depth of cut as process parameters and got the optimized value of MRR & SR. An L9 orthogonal array, the signal-to-noise (S/N) ratio are employed to the study the performance characteristics in the turning using WNMG332RP carbide insert with a nose radius of 0.8mm. Taguchi method is used to optimize surface roughness and material removal rate (MRR) during machining operation on CNC turning. The experimental result shows that on increasing depth of cut and feed the combined S/N ratio increases while on increasing cutting speed the combined S/N ratio decreases. It results that cutting speed is most significantly influences the Surface roughness followed by feed and in case of MRR, depth of cut is the most significant parameter followed by cutting speed .While the combination of both is most significantly affected by the depth of cut followed by the feed.
Content Comparative Investigation on Tool Wear During End Milling of AISI H13...journalBEEI
Tool wear prediction plays a significant role in machining industry for proper planning and control machining parameters and optimization of cutting conditions. This paper aims to investigate the effect of tool path strategies that are contour-in and zigzag tool path strategies applied on tool wear during pocket milling process. The experiments were carried out on CNC vertical machining centre by involving PVD coated carbide inserts. Cutting speed, feed rate and depth of cut were set to vary. In an experiment with three factors at three levels, Response Surface Method (RSM) design of experiment with a standard called Central Composite Design (CCD) was employed. Results obtained indicate that tool wear increases significantly at higher range of feed per tooth compared to cutting speed and depth of cut. This result of this experimental work is then proven statistically by developing empirical model. The prediction model for the response variable of tool wear for contour-in strategy developed in this research shows a good agreement with experimental work.
Optimization of Process Parameters of Tool Wear in Turning OperationIJERA Editor
Tool Wear is of great apprehension in machining industries since itaffects the surface quality, dimensional accuracy and production cost of the materials / components. In the present study twenty seven experiments were conducted as per 3 parameter 3 level full factorial design for turning operation of a mild steel specimen with high speed steel (HSS) cutting tool. An experimental investigation on cutting tool wear and a mathematical model for tool wear estimation is reported in this paper where the model was simulated by computer programming and it has been found that this model is capable of estimating the wear rate of cutting tool and it provides an optimum set of process parameters for minimum tool wear.
Optimization of Cylindrical Grinding Process Parameters on C40E Steel Using T...IJERA Editor
Surface finish and dimensional accuracy play a vital role in the today’s engineering industry. There are several methods used to achieve good surface finish like burnishing, honing and lapping, and grinding. Grinding is one of these ways that improves the surface finish and dimensional accuracy simultaneously. C40E steel has good industrial application in manufacturing of shafts, axles, spindles, studs, etc. In the present work the cylindrical grinding of C40E steel is done for the optimization of grinding process parameters. During this experimental work input process parameters i.e. speed, feed, depth of cut is optimized using Taguchi L9 orthogonal array. Analysis of variance (ANOVA) concluded that surface roughness is minimum at the 210 rpm, 0.11mm/rev feed, and 0.04mm depth of penetration.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
PARAMETER OPTIMIZATION IN VERTICAL MACHINING CENTER CNC FOR EN45 (STEEL ALLOY...IAEME Publication
Now days optimal machining parameters are of great concern in manufacturing environments, where economy of machining operations plays a key role in competitiveness in the market. This paper aims at developing a statistical model to optimize the surface parameters such as material removal rate (MRR) and surface roughness (SR).Response Surface Methodology (RSM) experimental design was used for conducting experiment. The experimental study was carried out in a CNC vertical machining center. The work piece material was EN45 (steel alloy).EN45 is widely used in the motor vehicle industry for leaf springs, truncated conical springs, helical springs and many general applications.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
OPTIMIZATION OF CUTTING PARAMETERS FOR CUTTING FORCE IN TURNING OF AISI 904L...ijiert bestjournal
Austenitic stainless steel is one of the most important engineering materials with wide variety
of applications. Superior resistance to corrosion and compatibility in high temperature and
high vacuum has particularly made it an attractive choice. However, the machinability of
austenitic stainless steel is not very promising owing to lower thermal conductivity, higher
degree of ductility and work harden ability. Chromium, Nickel, Copper and Molybdenum
gives 904L better corrosion resistance properties in sulphuric and phosphoric acid
environment. It has excellent forming and welding characteristics.
The present work is concentrated on dry turning of 904L. In this study the effect of cutting
parameters on cutting force is studied by experimentation. A plan of experiments is done by
Taguchi design of experiments to acquire data. The obtained data is validated by calculating
S/N ratio and plotting a graph.
Design &Analysis of Pure Iron Casting with Different MouldsIJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Optimization of Process Parameters of Tool Wear in Turning OperationIJERA Editor
Tool Wear is of great apprehension in machining industries since itaffects the surface quality, dimensional accuracy and production cost of the materials / components. In the present study twenty seven experiments were conducted as per 3 parameter 3 level full factorial design for turning operation of a mild steel specimen with high speed steel (HSS) cutting tool. An experimental investigation on cutting tool wear and a mathematical model for tool wear estimation is reported in this paper where the model was simulated by computer programming and it has been found that this model is capable of estimating the wear rate of cutting tool and it provides an optimum set of process parameters for minimum tool wear.
Optimization of Cylindrical Grinding Process Parameters on C40E Steel Using T...IJERA Editor
Surface finish and dimensional accuracy play a vital role in the today’s engineering industry. There are several methods used to achieve good surface finish like burnishing, honing and lapping, and grinding. Grinding is one of these ways that improves the surface finish and dimensional accuracy simultaneously. C40E steel has good industrial application in manufacturing of shafts, axles, spindles, studs, etc. In the present work the cylindrical grinding of C40E steel is done for the optimization of grinding process parameters. During this experimental work input process parameters i.e. speed, feed, depth of cut is optimized using Taguchi L9 orthogonal array. Analysis of variance (ANOVA) concluded that surface roughness is minimum at the 210 rpm, 0.11mm/rev feed, and 0.04mm depth of penetration.
International Journal of Computational Engineering Research(IJCER)ijceronline
International Journal of Computational Engineering Research(IJCER) is an intentional online Journal in English monthly publishing journal. This Journal publish original research work that contributes significantly to further the scientific knowledge in engineering and Technology
PARAMETER OPTIMIZATION IN VERTICAL MACHINING CENTER CNC FOR EN45 (STEEL ALLOY...IAEME Publication
Now days optimal machining parameters are of great concern in manufacturing environments, where economy of machining operations plays a key role in competitiveness in the market. This paper aims at developing a statistical model to optimize the surface parameters such as material removal rate (MRR) and surface roughness (SR).Response Surface Methodology (RSM) experimental design was used for conducting experiment. The experimental study was carried out in a CNC vertical machining center. The work piece material was EN45 (steel alloy).EN45 is widely used in the motor vehicle industry for leaf springs, truncated conical springs, helical springs and many general applications.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
OPTIMIZATION OF CUTTING PARAMETERS FOR CUTTING FORCE IN TURNING OF AISI 904L...ijiert bestjournal
Austenitic stainless steel is one of the most important engineering materials with wide variety
of applications. Superior resistance to corrosion and compatibility in high temperature and
high vacuum has particularly made it an attractive choice. However, the machinability of
austenitic stainless steel is not very promising owing to lower thermal conductivity, higher
degree of ductility and work harden ability. Chromium, Nickel, Copper and Molybdenum
gives 904L better corrosion resistance properties in sulphuric and phosphoric acid
environment. It has excellent forming and welding characteristics.
The present work is concentrated on dry turning of 904L. In this study the effect of cutting
parameters on cutting force is studied by experimentation. A plan of experiments is done by
Taguchi design of experiments to acquire data. The obtained data is validated by calculating
S/N ratio and plotting a graph.
Design &Analysis of Pure Iron Casting with Different MouldsIJMER
International Journal of Modern Engineering Research (IJMER) is Peer reviewed, online Journal. It serves as an international archival forum of scholarly research related to engineering and science education.
Full factorial method for optimization of process parameters for surface roug...Editor IJMTER
Quality and productivity play significant role in today’s manufacturing market.In
machining operations, achieving desired surface quality features of the machined product, is really a
challenging job on cnc machine. Because, these quality features are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of process parameters. There are a
number of parameters like cutting speed, feed and depth of cut etc. which must be given
consideration during the machining of SS 316L. The prediction of optimal machining conditions for
good surface roughness and material removal rate plays a very important role in process planning.
GEOMETRIC OPTIMIZATION AND MANUFACTURING PROCESS OF SIX CYLINDER DIESEL ENGIN...Ijripublishers Ijri
The crankshaft is that part of an engine which translates reciprocating linear piston motion into rotation. To convert the
reciprocating motion into rotation, the crankshaft has "crank" or "crankpins", additional bearing surfaces whose axis is
offset from that of the crank, to which the "big ends" of the connecting rods from each cylinder attach.
The aim of the project work is to optimize the geometry shape of 6-cylinder diesel engine crank shaft to reduce the failures
and to reduce the weight. And also this project work will provide the brief explanation of manufacturing process.
Initially literature survey and data collection will be done to understand methodology.
Design calculations will be done to get parameters of object for drafting.
3D model will be prepared according to the obtained parameters.
Analysis will be conducted on crank shaft to rectify failures by optimizing geometric shape. Also best material will be
suggested by analyzing and comparing results with the variation of materials.
Mold tool design will be done and assembly will be prepared according to that.
Cnc program will be prepared for die set using cam
MULTIOBJECTIVE OPTIMIZATION OF MACHINING PARAMETERSFOR C-65 MATERIAL USING TA...AVINASH JURIANI
CNC machines lead a major in a manufacturing industry, machining comprises of wide variety of operations with turning operation being the most important one. In turning operation performance specifications of concern include surface
finish, material removal rate& tolerance which are mostly affected by different
machining parameters like machining condition, work piece, tool geometry and
operating parameters. Among all of them operating parameter and tool
geometry is the most important parameter for better surface finish. This
project presents the optimization of various operating parameters as velocity,
feed and depth of cut for proper selection of tool inserts for surface finish. The
experiment was conducted on CNC lathe with C-65 shaft material. Taguchi’s
statistical analysis was employed for single optimization as it provides an
effective method for product designing which operate continuously over
varying conditions surface roughness and depth of cut is the most effective
parameter for material removal rate. Best parameter combinations for
optimum surface roughness are speed (A) at level 2 (191 m/min), feed (B)
at level 1 (0.2 mm/rev), depth of cut (C) at level 3 (1.5 mm), for optimum
material removal rate are speed (A) at level 3 (254 m/min), feed (B) at level 3
(0.3 mm/rev), depth of cut (C) at level 3 (1.5 mm). GRG optimum
parameters for SR and MRR are Speed (A) at level 2 (191 m/min), feed (B)
at level 1 (0.2 mm/rev), depth of cut (C) at level 3 (1.5 mm)
MULTI OBJECTIVE OPTIMIZATION OF CUTTING PARAMETERS IN TURNING OPERATION OF ST...IAEME Publication
Turning is a machining operation in which the cutting tool moves linearly while the work piece rotates to remove material. Turning is one the most important machining operation in
industries. The process of turning is influenced by many factors such as the cutting velocity, feed rate, depth of cut, geometry of cutting tool cutting conditions etc.
Effects of Cutting Tool Parameters on Surface Roughnessirjes
This paper presents of the influence on surface roughness of Co28Cr6Mo medical alloy machined
on a CNC lathe based on cutting parameters (rotational speed, feed rate, depth of cut and nose radius).The
influences of cutting parameters have been presented in graphical form for understanding. To achieve the
minimum surface roughness, the optimum values obtained for rpm, feed rate, depth of cut and nose radius were
respectively, 318 rpm, 0,1 mm/rev, 0,7 mm and 0,8 mm. Maximum surface roughness has been revealed the
values obtained for rpm, feed rate, depth of cut and nose radius were respectively, 318 rpm, 0,25 mm/rev, 0,9
mm and 0,4 mm.
Sustainable Manufacturing: Optimization of single pass Turning machining oper...sajal dixit
Main aim is to optimize a manufacturing process by using different Meta-heuristic algorithm. i had selected turning process here. Firstly i found the most influential parameters in turning process by introducing "Local-centrality Method". Optimization of these most influential parameters will lead to the optimization of whole process using "Genetic algorithm and Taguchi Method". Genetic algorithm has been used to optimize production rate & production cost and Taguchi method has been used to optimize cutting quality, which has been described in presentation.
Parametric analysis and multi objective optimization of cutting parameters in...eSAT Journals
Abstract Modern manufacturers, seeking to remain competitive in the market, rely on their Manufacturing engineers and production personnel to quickly and effectively set up manufacturing processes for new products. This paper presents the multi response optimization of turning parameters for Turning on AISI 4340 Alloy Steel. Experiments are designed and conducted based on Taguchi’s L27 Orthogonal array design. This paper discusses an investigation into the use of Taguchi parameter Design and Regression analysis to predict and optimize the Surface Roughness, Metal Removal Rate and Power Consumption in turning operations using CVD Cutting Tool. The Analysis of Variance (ANOVA) is employed to analyze the influence of Process Parameters during Turning. This paper also remarks the advantages of multi-objective optimization approach over the single-objective one. The useful results have been obtained by this research for other similar type of studies and can be helpful for further research works on the Tool life and Vibration of tools etc. Keywords: Turning, Ra, MRR, PC, Taguchi, Anova etc…
OPTIMIZATION OF MACHINING PARAMETERS WITH TOOL INSERT SELECTION FOR S355J2G3 ...AVINASH JURIANI
The key goal of modern manufacturing industries is increased productivity & high quality
Surface Roughness is major concern for quality aspects affecting performance.
Speed, Feed & Depth of cut mainly influences SR & MRR in Turning
Taguchi & Grey Relational Technique is used for optimization followed by ANOVA for contribution
MADM is the need for better Tool Insert Selection to get requisite surface finish
The big challenge of the mass production firms is concentrated for achieving high quality
products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning
process parameters on hard EN 31 material, for optimization of surface roughness, material removal
rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out
by considering four controllable input variables namely cutting speed, feed rate, depth of cut and
insert nose radius in the presence of wet & MQL system. This experiment also present the relation
between chip formations and controllable variables along with chip thickness, chip colors & chip
velocity from which its effect on insert wear, quality of product can be easily found out, because of
chip morphology gives indirectly the effect of it on the insert wear. In this dissertation work
minimum quantity lubrication system is used for reducing the cutting zone temperature properly and
very fastly. Finally comparison is carried out between wet and minimum quantity lubrication system
from which one can easily identify which system is better for higher productivity along with high
surface finish. This work also present the productivity (MRR) concept in production. The design of
experiment and optimization of surface roughness, material removal rate, machining time is carried
out by using response surface methodology (RSM). Central composite design method is used (CCD)
for the total experimental design work and its analysis and also for optimization of turning process
parameter by which wastage of the machining time, power can be avoided.
OPTIMIZATION OF TURNING PROCESS PARAMETER IN DRY TURNING OF SAE52100 STEELIAEME Publication
This paper presents the optimization of surface roughness & material removal rate in dry turning of SAE52100 steel. Carbide inserts were used for machining of SAE 52100 to study effects of process parameters [Cutting speed (S), Feed (F) and depth of cut (d)]. These models can be effectively used to predict the surface roughness (Ra) & material removal rate of the workpiece. The big challenge of the Micro, small& medium industries in India for achieving high quality
products with increased productivity.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
INVESTIGATION AND OPTIMIZATION OF TURNING PROCESS PARAMETER IN WET AND MQL SY...IAEME Publication
The big challenge of the mass production firms is concentrated for achieving high quality products with good dimensionability with high productivity, less wear on the cutting insert, less use
of cutting fluid, within less time. This paper present dissertation work of an investigation of turning process parameters on hard EN 31 material, for optimization of surface roughness, material removal rate, machining time in wet and minimum quantity lubrication system. The experiment is carried out by considering four controllable input variables namely cutting speed, feed rate, depth of cut and insert nose radius in the presence of wet & MQL system
Optimization of hard part turning of bohler K 110 steel with multiple perform...IAEME Publication
Böhler K110 material is used in High-duty cutting tools, blanking and punching tools& small moulds for the plastics industry where excellent wear resistance is required. It is difficult to machine the material in the hardened state (58 HRc).
Similar to Investigation of turning process to improve productivity mrr for better surface finish of al (20)
Submission Deadline: 30th September 2022
Acceptance Notification: Within Three Days’ time period
Online Publication: Within 24 Hrs. time Period
Expected Date of Dispatch of Printed Journal: 5th October 2022
MODELING AND ANALYSIS OF SURFACE ROUGHNESS AND WHITE LATER THICKNESS IN WIRE-...IAEME Publication
White layer thickness (WLT) formed and surface roughness in wire electric discharge turning (WEDT) of tungsten carbide composite has been made to model through response surface methodology (RSM). A Taguchi’s standard Design of experiments involving five input variables with three levels has been employed to establish a mathematical model between input parameters and responses. Percentage of cobalt content, spindle speed, Pulse on-time, wire feed and pulse off-time were changed during the experimental tests based on the Taguchi’s orthogonal array L27 (3^13). Analysis of variance (ANOVA) revealed that the mathematical models obtained can adequately describe performance within the parameters of the factors considered. There was a good agreement between the experimental and predicted values in this study.
A STUDY ON THE REASONS FOR TRANSGENDER TO BECOME ENTREPRENEURSIAEME Publication
The study explores the reasons for a transgender to become entrepreneurs. In this study transgender entrepreneur was taken as independent variable and reasons to become as dependent variable. Data were collected through a structured questionnaire containing a five point Likert Scale. The study examined the data of 30 transgender entrepreneurs in Salem Municipal Corporation of Tamil Nadu State, India. Simple Random sampling technique was used. Garrett Ranking Technique (Percentile Position, Mean Scores) was used as the analysis for the present study to identify the top 13 stimulus factors for establishment of trans entrepreneurial venture. Economic advancement of a nation is governed upon the upshot of a resolute entrepreneurial doings. The conception of entrepreneurship has stretched and materialized to the socially deflated uncharted sections of transgender community. Presently transgenders have smashed their stereotypes and are making recent headlines of achievements in various fields of our Indian society. The trans-community is gradually being observed in a new light and has been trying to achieve prospective growth in entrepreneurship. The findings of the research revealed that the optimistic changes are taking place to change affirmative societal outlook of the transgender for entrepreneurial ventureship. It also laid emphasis on other transgenders to renovate their traditional living. The paper also highlights that legislators, supervisory body should endorse an impartial canons and reforms in Tamil Nadu Transgender Welfare Board Association.
BROAD UNEXPOSED SKILLS OF TRANSGENDER ENTREPRENEURSIAEME Publication
Since ages gender difference is always a debatable theme whether caused by nature, evolution or environment. The birth of a transgender is dreadful not only for the child but also for their parents. The pain of living in the wrong physique and treated as second class victimized citizen is outrageous and fully harboured with vicious baseless negative scruples. For so long, social exclusion had perpetuated inequality and deprivation experiencing ingrained malign stigma and besieged victims of crime or violence across their life spans. They are pushed into the murky way of life with a source of eternal disgust, bereft sexual potency and perennial fear. Although they are highly visible but very little is known about them. The common public needs to comprehend the ravaged arrogance on these insensitive souls and assist in integrating them into the mainstream by offering equal opportunity, treat with humanity and respect their dignity. Entrepreneurship in the current age is endorsing the gender fairness movement. Unstable careers and economic inadequacy had inclined one of the gender variant people called Transgender to become entrepreneurs. These tiny budding entrepreneurs resulted in economic transition by means of employment, free from the clutches of stereotype jobs, raised standard of living and handful of financial empowerment. Besides all these inhibitions, they were able to witness a platform for skill set development that ignited them to enter into entrepreneurial domain. This paper epitomizes skill sets involved in trans-entrepreneurs of Thoothukudi Municipal Corporation of Tamil Nadu State and is a groundbreaking determination to sightsee various skills incorporated and the impact on entrepreneurship.
DETERMINANTS AFFECTING THE USER'S INTENTION TO USE MOBILE BANKING APPLICATIONSIAEME Publication
The banking and financial services industries are experiencing increased technology penetration. Among them, the banking industry has made technological advancements to better serve the general populace. The economy focused on transforming the banking sector's system into a cashless, paperless, and faceless one. The researcher wants to evaluate the user's intention for utilising a mobile banking application. The study also examines the variables affecting the user's behaviour intention when selecting specific applications for financial transactions. The researcher employed a well-structured questionnaire and a descriptive study methodology to gather the respondents' primary data utilising the snowball sampling technique. The study includes variables like performance expectations, effort expectations, social impact, enabling circumstances, and perceived risk. Each of the aforementioned variables has a major impact on how users utilise mobile banking applications. The outcome will assist the service provider in comprehending the user's history with mobile banking applications.
ANALYSE THE USER PREDILECTION ON GPAY AND PHONEPE FOR DIGITAL TRANSACTIONSIAEME Publication
Technology upgradation in banking sector took the economy to view that payment mode towards online transactions using mobile applications. This system enabled connectivity between banks, Merchant and user in a convenient mode. there are various applications used for online transactions such as Google pay, Paytm, freecharge, mobikiwi, oxygen, phonepe and so on and it also includes mobile banking applications. The study aimed at evaluating the predilection of the user in adopting digital transaction. The study is descriptive in nature. The researcher used random sample techniques to collect the data. The findings reveal that mobile applications differ with the quality of service rendered by Gpay and Phonepe. The researcher suggest the Phonepe application should focus on implementing the application should be user friendly interface and Gpay on motivating the users to feel the importance of request for money and modes of payments in the application.
VOICE BASED ATM FOR VISUALLY IMPAIRED USING ARDUINOIAEME Publication
The prototype of a voice-based ATM for visually impaired using Arduino is to help people who are blind. This uses RFID cards which contain users fingerprint encrypted on it and interacts with the users through voice commands. ATM operates when sensor detects the presence of one person in the cabin. After scanning the RFID card, it will ask to select the mode like –normal or blind. User can select the respective mode through voice input, if blind mode is selected the balance check or cash withdraw can be done through voice input. Normal mode procedure is same as the existing ATM.
IMPACT OF EMOTIONAL INTELLIGENCE ON HUMAN RESOURCE MANAGEMENT PRACTICES AMONG...IAEME Publication
There is increasing acceptability of emotional intelligence as a major factor in personality assessment and effective human resource management. Emotional intelligence as the ability to build capacity, empathize, co-operate, motivate and develop others cannot be divorced from both effective performance and human resource management systems. The human person is crucial in defining organizational leadership and fortunes in terms of challenges and opportunities and walking across both multinational and bilateral relationships. The growing complexity of the business world requires a great deal of self-confidence, integrity, communication, conflict and diversity management to keep the global enterprise within the paths of productivity and sustainability. Using the exploratory research design and 255 participants the result of this original study indicates strong positive correlation between emotional intelligence and effective human resource management. The paper offers suggestions on further studies between emotional intelligence and human capital development and recommends for conflict management as an integral part of effective human resource management.
VISUALISING AGING PARENTS & THEIR CLOSE CARERS LIFE JOURNEY IN AGING ECONOMYIAEME Publication
Our life journey, in general, is closely defined by the way we understand the meaning of why we coexist and deal with its challenges. As we develop the "inspiration economy", we could say that nearly all of the challenges we have faced are opportunities that help us to discover the rest of our journey. In this note paper, we explore how being faced with the opportunity of being a close carer for an aging parent with dementia brought intangible discoveries that changed our insight of the meaning of the rest of our life journey.
A STUDY ON THE IMPACT OF ORGANIZATIONAL CULTURE ON THE EFFECTIVENESS OF PERFO...IAEME Publication
The main objective of this study is to analyze the impact of aspects of Organizational Culture on the Effectiveness of the Performance Management System (PMS) in the Health Care Organization at Thanjavur. Organizational Culture and PMS play a crucial role in present-day organizations in achieving their objectives. PMS needs employees’ cooperation to achieve its intended objectives. Employees' cooperation depends upon the organization’s culture. The present study uses exploratory research to examine the relationship between the Organization's culture and the Effectiveness of the Performance Management System. The study uses a Structured Questionnaire to collect the primary data. For this study, Thirty-six non-clinical employees were selected from twelve randomly selected Health Care organizations at Thanjavur. Thirty-two fully completed questionnaires were received.
Living in 21st century in itself reminds all of us the necessity of police and its administration. As more and more we are entering into the modern society and culture, the more we require the services of the so called ‘Khaki Worthy’ men i.e., the police personnel. Whether we talk of Indian police or the other nation’s police, they all have the same recognition as they have in India. But as already mentioned, their services and requirements are different after the like 26th November, 2008 incidents, where they without saving their own lives has sacrificed themselves without any hitch and without caring about their respective family members and wards. In other words, they are like our heroes and mentors who can guide us from the darkness of fear, militancy, corruption and other dark sides of life and so on. Now the question arises, if Gandhi would have been alive today, what would have been his reaction/opinion to the police and its functioning? Would he have some thing different in his mind now what he had been in his mind before the partition or would he be going to start some Satyagraha in the form of some improvement in the functioning of the police administration? Really these questions or rather night mares can come to any one’s mind, when there is too much confusion is prevailing in our minds, when there is too much corruption in the society and when the polices working is also in the questioning because of one or the other case throughout the India. It is matter of great concern that we have to thing over our administration and our practical approach because the police personals are also like us, they are part and parcel of our society and among one of us, so why we all are pin pointing towards them.
A STUDY ON TALENT MANAGEMENT AND ITS IMPACT ON EMPLOYEE RETENTION IN SELECTED...IAEME Publication
The goal of this study was to see how talent management affected employee retention in the selected IT organizations in Chennai. The fundamental issue was the difficulty to attract, hire, and retain talented personnel who perform well and the gap between supply and demand of talent acquisition and retaining them within the firms. The study's main goals were to determine the impact of talent management on employee retention in IT companies in Chennai, investigate talent management strategies that IT companies could use to improve talent acquisition, performance management, career planning and formulate retention strategies that the IT firms could use. The respondents were given a structured close-ended questionnaire with the 5 Point Likert Scale as part of the study's quantitative research design. The target population consisted of 289 IT professionals. The questionnaires were distributed and collected by the researcher directly. The Statistical Package for Social Sciences (SPSS) was used to collect and analyse the questionnaire responses. Hypotheses that were formulated for the various areas of the study were tested using a variety of statistical tests. The key findings of the study suggested that talent management had an impact on employee retention. The studies also found that there is a clear link between the implementation of talent management and retention measures. Management should provide enough training and development for employees, clarify job responsibilities, provide adequate remuneration packages, and recognise employees for exceptional performance.
ATTRITION IN THE IT INDUSTRY DURING COVID-19 PANDEMIC: LINKING EMOTIONAL INTE...IAEME Publication
Globally, Millions of dollars were spent by the organizations for employing skilled Information Technology (IT) professionals. It is costly to replace unskilled employees with IT professionals possessing technical skills and competencies that aid in interconnecting the business processes. The organization’s employment tactics were forced to alter by globalization along with technological innovations as they consistently diminish to remain lean, outsource to concentrate on core competencies along with restructuring/reallocate personnel to gather efficiency. As other jobs, organizations or professions have become reasonably more appropriate in a shifting employment landscape, the above alterations trigger both involuntary as well as voluntary turnover. The employee view on jobs is also afflicted by the COVID-19 pandemic along with the employee-driven labour market. So, having effective strategies is necessary to tackle the withdrawal rate of employees. By associating Emotional Intelligence (EI) along with Talent Management (TM) in the IT industry, the rise in attrition rate was analyzed in this study. Only 303 respondents were collected out of 350 participants to whom questionnaires were distributed. From the employees of IT organizations located in Bangalore (India), the data were congregated. A simple random sampling methodology was employed to congregate data as of the respondents. Generating the hypothesis along with testing is eventuated. The effect of EI and TM along with regression analysis between TM and EI was analyzed. The outcomes indicated that employee and Organizational Performance (OP) were elevated by effective EI along with TM.
INFLUENCE OF TALENT MANAGEMENT PRACTICES ON ORGANIZATIONAL PERFORMANCE A STUD...IAEME Publication
By implementing talent management strategy, organizations would have the option to retain their skilled professionals while additionally working on their overall performance. It is the course of appropriately utilizing the ideal individuals, setting them up for future top positions, exploring and dealing with their performance, and holding them back from leaving the organization. It is employee performance that determines the success of every organization. The firm quickly obtains an upper hand over its rivals in the event that its employees having particular skills that cannot be duplicated by the competitors. Thus, firms are centred on creating successful talent management practices and processes to deal with the unique human resources. Firms are additionally endeavouring to keep their top/key staff since on the off chance that they leave; the whole store of information leaves the firm's hands. The study's objective was to determine the impact of talent management on organizational performance among the selected IT organizations in Chennai. The study recommends that talent management limitedly affects performance. On the off chance that this talent is appropriately management and implemented properly, organizations might benefit as much as possible from their maintained assets to support development and productivity, both monetarily and non-monetarily.
A STUDY OF VARIOUS TYPES OF LOANS OF SELECTED PUBLIC AND PRIVATE SECTOR BANKS...IAEME Publication
Banking regulations act of India, 1949 defines banking as “acceptance of deposits for the purpose of lending or investment from the public, repayment on demand or otherwise and withdrawable through cheques, drafts order or otherwise”, the major participants of the Indian financial system are commercial banks, the financial institution encompassing term lending institutions. Investments institutions, specialized financial institution and the state level development banks, non banking financial companies (NBFC) and other market intermediaries such has the stock brokers and money lenders are among the oldest of the certain variants of NBFC and the oldest market participants. The asset quality of banks is one of the most important indicators of their financial health. The Indian banking sector has been facing severe problems of increasing Non- Performing Assets (NPAs). The NPAs growth directly and indirectly affects the quality of assets and profitability of banks. It also shows the efficiency of banks credit risk management and the recovery effectiveness. NPA do not generate any income, whereas, the bank is required to make provisions for such as assets that why is a double edge weapon. This paper outlines the concept of quality of bank loans of different types like Housing, Agriculture and MSME loans in state Haryana of selected public and private sector banks. This study is highlighting problems associated with the role of commercial bank in financing Small and Medium Scale Enterprises (SME). The overall objective of the research was to assess the effect of the financing provisions existing for the setting up and operations of MSMEs in the country and to generate recommendations for more robust financing mechanisms for successful operation of the MSMEs, in turn understanding the impact of MSME loans on financial institutions due to NPA. There are many research conducted on the topic of Non- Performing Assets (NPA) Management, concerning particular bank, comparative study of public and private banks etc. In this paper the researcher is considering the aggregate data of selected public sector and private sector banks and attempts to compare the NPA of Housing, Agriculture and MSME loans in state Haryana of public and private sector banks. The tools used in the study are average and Anova test and variance. The findings reveal that NPA is common problem for both public and private sector banks and is associated with all types of loans either that is housing loans, agriculture loans and loans to SMES. NPAs of both public and private sector banks show the increasing trend. In 2010-11 GNPA of public and private sector were at same level it was 2% but after 2010-11 it increased in many fold and at present there is GNPA in some more than 15%. It shows the dark area of Indian banking sector.
EXPERIMENTAL STUDY OF MECHANICAL AND TRIBOLOGICAL RELATION OF NYLON/BaSO4 POL...IAEME Publication
An experiment conducted in this study found that BaSO4 changed Nylon 6's mechanical properties. By changing the weight ratios, BaSO4 was used to make Nylon 6. This Researcher looked into how hard Nylon-6/BaSO4 composites are and how well they wear. Experiments were done based on Taguchi design L9. Nylon-6/BaSO4 composites can be tested for their hardness number using a Rockwell hardness testing apparatus. On Nylon/BaSO4, the wear behavior was measured by a wear monitor, pinon-disc friction by varying reinforcement, sliding speed, and sliding distance, and the microstructure of the crack surfaces was observed by SEM. This study provides significant contributions to ultimate strength by increasing BaSO4 content up to 16% in the composites, and sliding speed contributes 72.45% to the wear rate
ROLE OF SOCIAL ENTREPRENEURSHIP IN RURAL DEVELOPMENT OF INDIA - PROBLEMS AND ...IAEME Publication
The majority of the population in India lives in villages. The village is the back bone of the country. Village or rural industries play an important role in the national economy, particularly in the rural development. Developing the rural economy is one of the key indicators towards a country’s success. Whether it be the need to look after the welfare of the farmers or invest in rural infrastructure, Governments have to ensure that rural development isn’t compromised. The economic development of our country largely depends on the progress of rural areas and the standard of living of rural masses. Village or rural industries play an important role in the national economy, particularly in the rural development. Rural entrepreneurship is based on stimulating local entrepreneurial talent and the subsequent growth of indigenous enterprises. It recognizes opportunity in the rural areas and accelerates a unique blend of resources either inside or outside of agriculture. Rural entrepreneurship brings an economic value to the rural sector by creating new methods of production, new markets, new products and generate employment opportunities thereby ensuring continuous rural development. Social Entrepreneurship has the direct and primary objective of serving the society along with the earning profits. So, social entrepreneurship is different from the economic entrepreneurship as its basic objective is not to earn profits but for providing innovative solutions to meet the society needs which are not taken care by majority of the entrepreneurs as they are in the business for profit making as a sole objective. So, the Social Entrepreneurs have the huge growth potential particularly in the developing countries like India where we have huge societal disparities in terms of the financial positions of the population. Still 22 percent of the Indian population is below the poverty line and also there is disparity among the rural & urban population in terms of families living under BPL. 25.7 percent of the rural population & 13.7 percent of the urban population is under BPL which clearly shows the disparity of the poor people in the rural and urban areas. The need to develop social entrepreneurship in agriculture is dictated by a large number of social problems. Such problems include low living standards, unemployment, and social tension. The reasons that led to the emergence of the practice of social entrepreneurship are the above factors. The research problem lays upon disclosing the importance of role of social entrepreneurship in rural development of India. The paper the tendencies of social entrepreneurship in India, to present successful examples of such business for providing recommendations how to improve situation in rural areas in terms of social entrepreneurship development. Indian government has made some steps towards development of social enterprises, social entrepreneurship, and social in- novation, but a lot remains to be improved.
OPTIMAL RECONFIGURATION OF POWER DISTRIBUTION RADIAL NETWORK USING HYBRID MET...IAEME Publication
Distribution system is a critical link between the electric power distributor and the consumers. Most of the distribution networks commonly used by the electric utility is the radial distribution network. However in this type of network, it has technical issues such as enormous power losses which affect the quality of the supply. Nowadays, the introduction of Distributed Generation (DG) units in the system help improve and support the voltage profile of the network as well as the performance of the system components through power loss mitigation. In this study network reconfiguration was done using two meta-heuristic algorithms Particle Swarm Optimization and Gravitational Search Algorithm (PSO-GSA) to enhance power quality and voltage profile in the system when simultaneously applied with the DG units. Backward/Forward Sweep Method was used in the load flow analysis and simulated using the MATLAB program. Five cases were considered in the Reconfiguration based on the contribution of DG units. The proposed method was tested using IEEE 33 bus system. Based on the results, there was a voltage profile improvement in the system from 0.9038 p.u. to 0.9594 p.u.. The integration of DG in the network also reduced power losses from 210.98 kW to 69.3963 kW. Simulated results are drawn to show the performance of each case.
APPLICATION OF FRUGAL APPROACH FOR PRODUCTIVITY IMPROVEMENT - A CASE STUDY OF...IAEME Publication
Manufacturing industries have witnessed an outburst in productivity. For productivity improvement manufacturing industries are taking various initiatives by using lean tools and techniques. However, in different manufacturing industries, frugal approach is applied in product design and services as a tool for improvement. Frugal approach contributed to prove less is more and seems indirectly contributing to improve productivity. Hence, there is need to understand status of frugal approach application in manufacturing industries. All manufacturing industries are trying hard and putting continuous efforts for competitive existence. For productivity improvements, manufacturing industries are coming up with different effective and efficient solutions in manufacturing processes and operations. To overcome current challenges, manufacturing industries have started using frugal approach in product design and services. For this study, methodology adopted with both primary and secondary sources of data. For primary source interview and observation technique is used and for secondary source review has done based on available literatures in website, printed magazines, manual etc. An attempt has made for understanding application of frugal approach with the study of manufacturing industry project. Manufacturing industry selected for this project study is Mahindra and Mahindra Ltd. This paper will help researcher to find the connections between the two concepts productivity improvement and frugal approach. This paper will help to understand significance of frugal approach for productivity improvement in manufacturing industry. This will also help to understand current scenario of frugal approach in manufacturing industry. In manufacturing industries various process are involved to deliver the final product. In the process of converting input in to output through manufacturing process productivity plays very critical role. Hence this study will help to evolve status of frugal approach in productivity improvement programme. The notion of frugal can be viewed as an approach towards productivity improvement in manufacturing industries.
A MULTIPLE – CHANNEL QUEUING MODELS ON FUZZY ENVIRONMENTIAEME Publication
In this paper, we investigated a queuing model of fuzzy environment-based a multiple channel queuing model (M/M/C) ( /FCFS) and study its performance under realistic conditions. It applies a nonagonal fuzzy number to analyse the relevant performance of a multiple channel queuing model (M/M/C) ( /FCFS). Based on the sub interval average ranking method for nonagonal fuzzy number, we convert fuzzy number to crisp one. Numerical results reveal that the efficiency of this method. Intuitively, the fuzzy environment adapts well to a multiple channel queuing models (M/M/C) ( /FCFS) are very well.
Memorandum Of Association Constitution of Company.pptseri bangash
www.seribangash.com
A Memorandum of Association (MOA) is a legal document that outlines the fundamental principles and objectives upon which a company operates. It serves as the company's charter or constitution and defines the scope of its activities. Here's a detailed note on the MOA:
Contents of Memorandum of Association:
Name Clause: This clause states the name of the company, which should end with words like "Limited" or "Ltd." for a public limited company and "Private Limited" or "Pvt. Ltd." for a private limited company.
https://seribangash.com/article-of-association-is-legal-doc-of-company/
Registered Office Clause: It specifies the location where the company's registered office is situated. This office is where all official communications and notices are sent.
Objective Clause: This clause delineates the main objectives for which the company is formed. It's important to define these objectives clearly, as the company cannot undertake activities beyond those mentioned in this clause.
www.seribangash.com
Liability Clause: It outlines the extent of liability of the company's members. In the case of companies limited by shares, the liability of members is limited to the amount unpaid on their shares. For companies limited by guarantee, members' liability is limited to the amount they undertake to contribute if the company is wound up.
https://seribangash.com/promotors-is-person-conceived-formation-company/
Capital Clause: This clause specifies the authorized capital of the company, i.e., the maximum amount of share capital the company is authorized to issue. It also mentions the division of this capital into shares and their respective nominal value.
Association Clause: It simply states that the subscribers wish to form a company and agree to become members of it, in accordance with the terms of the MOA.
Importance of Memorandum of Association:
Legal Requirement: The MOA is a legal requirement for the formation of a company. It must be filed with the Registrar of Companies during the incorporation process.
Constitutional Document: It serves as the company's constitutional document, defining its scope, powers, and limitations.
Protection of Members: It protects the interests of the company's members by clearly defining the objectives and limiting their liability.
External Communication: It provides clarity to external parties, such as investors, creditors, and regulatory authorities, regarding the company's objectives and powers.
https://seribangash.com/difference-public-and-private-company-law/
Binding Authority: The company and its members are bound by the provisions of the MOA. Any action taken beyond its scope may be considered ultra vires (beyond the powers) of the company and therefore void.
Amendment of MOA:
While the MOA lays down the company's fundamental principles, it is not entirely immutable. It can be amended, but only under specific circumstances and in compliance with legal procedures. Amendments typically require shareholder
Putting the SPARK into Virtual Training.pptxCynthia Clay
This 60-minute webinar, sponsored by Adobe, was delivered for the Training Mag Network. It explored the five elements of SPARK: Storytelling, Purpose, Action, Relationships, and Kudos. Knowing how to tell a well-structured story is key to building long-term memory. Stating a clear purpose that doesn't take away from the discovery learning process is critical. Ensuring that people move from theory to practical application is imperative. Creating strong social learning is the key to commitment and engagement. Validating and affirming participants' comments is the way to create a positive learning environment.
Skye Residences | Extended Stay Residences Near Toronto Airportmarketingjdass
Experience unparalleled EXTENDED STAY and comfort at Skye Residences located just minutes from Toronto Airport. Discover sophisticated accommodations tailored for discerning travelers.
Website Link :
https://skyeresidences.com/
https://skyeresidences.com/about-us/
https://skyeresidences.com/gallery/
https://skyeresidences.com/rooms/
https://skyeresidences.com/near-by-attractions/
https://skyeresidences.com/commute/
https://skyeresidences.com/contact/
https://skyeresidences.com/queen-suite-with-sofa-bed/
https://skyeresidences.com/queen-suite-with-sofa-bed-and-balcony/
https://skyeresidences.com/queen-suite-with-sofa-bed-accessible/
https://skyeresidences.com/2-bedroom-deluxe-queen-suite-with-sofa-bed/
https://skyeresidences.com/2-bedroom-deluxe-king-queen-suite-with-sofa-bed/
https://skyeresidences.com/2-bedroom-deluxe-queen-suite-with-sofa-bed-accessible/
#Skye Residences Etobicoke, #Skye Residences Near Toronto Airport, #Skye Residences Toronto, #Skye Hotel Toronto, #Skye Hotel Near Toronto Airport, #Hotel Near Toronto Airport, #Near Toronto Airport Accommodation, #Suites Near Toronto Airport, #Etobicoke Suites Near Airport, #Hotel Near Toronto Pearson International Airport, #Toronto Airport Suite Rentals, #Pearson Airport Hotel Suites
Falcon stands out as a top-tier P2P Invoice Discounting platform in India, bridging esteemed blue-chip companies and eager investors. Our goal is to transform the investment landscape in India by establishing a comprehensive destination for borrowers and investors with diverse profiles and needs, all while minimizing risk. What sets Falcon apart is the elimination of intermediaries such as commercial banks and depository institutions, allowing investors to enjoy higher yields.
3.0 Project 2_ Developing My Brand Identity Kit.pptxtanyjahb
A personal brand exploration presentation summarizes an individual's unique qualities and goals, covering strengths, values, passions, and target audience. It helps individuals understand what makes them stand out, their desired image, and how they aim to achieve it.
Digital Transformation and IT Strategy Toolkit and TemplatesAurelien Domont, MBA
This Digital Transformation and IT Strategy Toolkit was created by ex-McKinsey, Deloitte and BCG Management Consultants, after more than 5,000 hours of work. It is considered the world's best & most comprehensive Digital Transformation and IT Strategy Toolkit. It includes all the Frameworks, Best Practices & Templates required to successfully undertake the Digital Transformation of your organization and define a robust IT Strategy.
Editable Toolkit to help you reuse our content: 700 Powerpoint slides | 35 Excel sheets | 84 minutes of Video training
This PowerPoint presentation is only a small preview of our Toolkits. For more details, visit www.domontconsulting.com
LA HUG - Video Testimonials with Chynna Morgan - June 2024Lital Barkan
Have you ever heard that user-generated content or video testimonials can take your brand to the next level? We will explore how you can effectively use video testimonials to leverage and boost your sales, content strategy, and increase your CRM data.🤯
We will dig deeper into:
1. How to capture video testimonials that convert from your audience 🎥
2. How to leverage your testimonials to boost your sales 💲
3. How you can capture more CRM data to understand your audience better through video testimonials. 📊
Attending a job Interview for B1 and B2 Englsih learnersErika906060
It is a sample of an interview for a business english class for pre-intermediate and intermediate english students with emphasis on the speking ability.
What is the TDS Return Filing Due Date for FY 2024-25.pdfseoforlegalpillers
It is crucial for the taxpayers to understand about the TDS Return Filing Due Date, so that they can fulfill your TDS obligations efficiently. Taxpayers can avoid penalties by sticking to the deadlines and by accurate filing of TDS. Timely filing of TDS will make sure about the availability of tax credits. You can also seek the professional guidance of experts like Legal Pillers for timely filing of the TDS Return.
Enterprise Excellence is Inclusive Excellence.pdfKaiNexus
Enterprise excellence and inclusive excellence are closely linked, and real-world challenges have shown that both are essential to the success of any organization. To achieve enterprise excellence, organizations must focus on improving their operations and processes while creating an inclusive environment that engages everyone. In this interactive session, the facilitator will highlight commonly established business practices and how they limit our ability to engage everyone every day. More importantly, though, participants will likely gain increased awareness of what we can do differently to maximize enterprise excellence through deliberate inclusion.
What is Enterprise Excellence?
Enterprise Excellence is a holistic approach that's aimed at achieving world-class performance across all aspects of the organization.
What might I learn?
A way to engage all in creating Inclusive Excellence. Lessons from the US military and their parallels to the story of Harry Potter. How belt systems and CI teams can destroy inclusive practices. How leadership language invites people to the party. There are three things leaders can do to engage everyone every day: maximizing psychological safety to create environments where folks learn, contribute, and challenge the status quo.
Who might benefit? Anyone and everyone leading folks from the shop floor to top floor.
Dr. William Harvey is a seasoned Operations Leader with extensive experience in chemical processing, manufacturing, and operations management. At Michelman, he currently oversees multiple sites, leading teams in strategic planning and coaching/practicing continuous improvement. William is set to start his eighth year of teaching at the University of Cincinnati where he teaches marketing, finance, and management. William holds various certifications in change management, quality, leadership, operational excellence, team building, and DiSC, among others.
Business Valuation Principles for EntrepreneursBen Wann
This insightful presentation is designed to equip entrepreneurs with the essential knowledge and tools needed to accurately value their businesses. Understanding business valuation is crucial for making informed decisions, whether you're seeking investment, planning to sell, or simply want to gauge your company's worth.