Horrible Crane accident , 2 people died include one safety officer in RIL Jamnagar
•Download as PPTX, PDF•
2 likes•4,775 views
A crane accident at a Reliance Industries site in Jamnagar, Gujarat, India on June 29, 2015 resulted in two deaths, including a safety officer. The crane operator failed to fully extend the outriggers of the 70-ton crane and did not account for uneven ground conditions, causing the crane to tip over during lifting operations and crush a nearby container with people inside. The accident took the lives of the crane operator helper and two other individuals, demonstrating the risks of operating heavy machinery without proper safety precautions.
Report
Share
Report
Share
Recommended
Hot Works Safety Training
CONTENTS:
I. What is a Hot Work ?
II. Training
III. PPE`s
IV. Hot Work Permit
V. Electric Welding
VI. Fire Prevention
VII. Fire Watch
VIII. Generator Sets
IX. Welding Equipment Checks
X. Oxy Cutting Equipment
XI. Fire Safety Precautions
XII. Compressed Gas Cylinders
XIII. Safe Practices
XIV. Heat Stress
Lifting & procedure
The document discusses lifting equipment and procedures as outlined in the Factories Act. It defines key terms like competent person, machinery, and lifting tackles. It provides guidelines for planning lifts, conducting the lift, landing loads, and dos and don'ts. It also examines sling angles and their effect on safe working loads. Case studies describe incidents where improper planning and techniques like misaligned loads led to injuries.
Crane Operation - Lifting
This document outlines safety precautions and procedures for crane operations. It establishes requirements for organizing a crane and rigging group with defined roles and responsibilities. It requires crane operators and signalmen to be qualified and trained. It specifies guidelines for crane set up and operation including following approved lift plans, permit requirements, and stopping work if unsafe conditions arise. It defines critical lifts and provides examples. It lists safety precautions for crane and rigging equipment inspections, defects, capacity markings, and color coding for monthly inspections.
Lifting tools
This document provides an overview of important factors related to safe lifting operations, including common accidents, legislative requirements, roles of personnel, machinery considerations, and types of lifting gears. It discusses cranes like mobile cranes and tower cranes and safe operation points. It also covers various lifting gears such as wire rope slings, chain slings, hooks, and their inspection and proper use. The document emphasizes the importance of following safety procedures and using qualified personnel and properly inspected equipment to reduce lifting accidents.
Industrial safetY of height works
Work at height refers to any work where a person could fall and be injured, including work at or below ground level. A work permit is required to ensure hazardous jobs are carried out safely. Safe work at heights involves avoiding work at heights if possible, preventing falls through fall protection devices like safety nets and harnesses, and using the proper access equipment like ladders, scaffolds, and mobile elevated work platforms. Proper erection, use, and inspection of this equipment is necessary to minimize fall risks.
Crane Safety Training Presentation
Cranes are machines used to lift and move heavy loads and come in several types including mobile, gantry, tower, and mechanical. There are two types of lifting - manual and mechanical using cranes or chain blocks. Different types of lifts include light, heavy, critical, and tandem lifts using two or more cranes. Crane operation can result in deaths from issues like power line contact, rigging failures, structure failures, tipping over, and swing radius crushing. Safety protocols include inspection checklists for rigging and removing damaged slings/ropes from service to prevent failures when lifting loads.
A Part 6 Lifting Operations
This document outlines regulations and guidelines for safe lifting operations and the use of lifting appliances. It discusses requirements for equipment strength and stability, prevention of injuries, thorough inspections and examinations. Various types of cranes and their safety devices are described. Factors to consider when selecting cranes include load size, lift heights and durations. Proper planning, supervision and safe practices are required for all lifting operations.
Hoisting and Rigging Safety
This document provides guidance on hoisting and rigging safety. It emphasizes the importance of training, knowing equipment limitations, inspecting all components for defects, avoiding electrical hazards, using proper sling configurations and rigging hardware, understanding hand signals, and following regulations around tag lines and overhead loads. Safety is ensured by knowing equipment ratings, using defect-free gear, having competent supervision, and taking precautions specific to each lifting situation.
Recommended
Hot Works Safety Training
CONTENTS:
I. What is a Hot Work ?
II. Training
III. PPE`s
IV. Hot Work Permit
V. Electric Welding
VI. Fire Prevention
VII. Fire Watch
VIII. Generator Sets
IX. Welding Equipment Checks
X. Oxy Cutting Equipment
XI. Fire Safety Precautions
XII. Compressed Gas Cylinders
XIII. Safe Practices
XIV. Heat Stress
Lifting & procedure
The document discusses lifting equipment and procedures as outlined in the Factories Act. It defines key terms like competent person, machinery, and lifting tackles. It provides guidelines for planning lifts, conducting the lift, landing loads, and dos and don'ts. It also examines sling angles and their effect on safe working loads. Case studies describe incidents where improper planning and techniques like misaligned loads led to injuries.
Crane Operation - Lifting
This document outlines safety precautions and procedures for crane operations. It establishes requirements for organizing a crane and rigging group with defined roles and responsibilities. It requires crane operators and signalmen to be qualified and trained. It specifies guidelines for crane set up and operation including following approved lift plans, permit requirements, and stopping work if unsafe conditions arise. It defines critical lifts and provides examples. It lists safety precautions for crane and rigging equipment inspections, defects, capacity markings, and color coding for monthly inspections.
Lifting tools
This document provides an overview of important factors related to safe lifting operations, including common accidents, legislative requirements, roles of personnel, machinery considerations, and types of lifting gears. It discusses cranes like mobile cranes and tower cranes and safe operation points. It also covers various lifting gears such as wire rope slings, chain slings, hooks, and their inspection and proper use. The document emphasizes the importance of following safety procedures and using qualified personnel and properly inspected equipment to reduce lifting accidents.
Industrial safetY of height works
Work at height refers to any work where a person could fall and be injured, including work at or below ground level. A work permit is required to ensure hazardous jobs are carried out safely. Safe work at heights involves avoiding work at heights if possible, preventing falls through fall protection devices like safety nets and harnesses, and using the proper access equipment like ladders, scaffolds, and mobile elevated work platforms. Proper erection, use, and inspection of this equipment is necessary to minimize fall risks.
Crane Safety Training Presentation
Cranes are machines used to lift and move heavy loads and come in several types including mobile, gantry, tower, and mechanical. There are two types of lifting - manual and mechanical using cranes or chain blocks. Different types of lifts include light, heavy, critical, and tandem lifts using two or more cranes. Crane operation can result in deaths from issues like power line contact, rigging failures, structure failures, tipping over, and swing radius crushing. Safety protocols include inspection checklists for rigging and removing damaged slings/ropes from service to prevent failures when lifting loads.
A Part 6 Lifting Operations
This document outlines regulations and guidelines for safe lifting operations and the use of lifting appliances. It discusses requirements for equipment strength and stability, prevention of injuries, thorough inspections and examinations. Various types of cranes and their safety devices are described. Factors to consider when selecting cranes include load size, lift heights and durations. Proper planning, supervision and safe practices are required for all lifting operations.
Hoisting and Rigging Safety
This document provides guidance on hoisting and rigging safety. It emphasizes the importance of training, knowing equipment limitations, inspecting all components for defects, avoiding electrical hazards, using proper sling configurations and rigging hardware, understanding hand signals, and following regulations around tag lines and overhead loads. Safety is ensured by knowing equipment ratings, using defect-free gear, having competent supervision, and taking precautions specific to each lifting situation.
Permit to work system
What is Permit to work system?
What are the requirements of permit to work?
Different types of permit to work system such electrical, hot and cold work etc.
Health And Safety Induction Training
This document outlines health and safety topics covered in an induction training. It discusses hazards associated with working at heights, proper use of ladders and scaffolding, fall protection, machine safety, chemical hazards, traffic safety, fire safety, and more. Safety signage and their meanings are explained. Penalties for safety infractions are listed to encourage compliance with safety rules and regulations. The goal is to educate workers on best practices to avoid accidents and injuries on the jobsite.
FORKLIFT SAFETY
Forklifts are extremely useful workplace vehicles, as long as they are used safely and appropriately by operators who are appropriately trained and competent to use them.
Forklifts can be dangerous: they account for 25% of injuries at work. Many workplace accidents involve people being hit or run over by forklift trucks (typically when the forklift is reversing) because the driver did not see them. Owing to their size and weight, injuries resulting from forklifts are generally very serious. Accidents involving them are often caused by poor supervision and a lack of training.
Always:
Wear appropriate personal protective clothing as provided by employer. Hard hat, protective footwear and high visibility clothing are recommended as a minimum when working around forklifts. Other equipment may be needed depending on the working environment
Report defects immediately to supervisor
Make sure work path is free of obstructions
Wear operator restraints, where fitted
Look all around before moving off
Look in the direction of travel
Avoid sudden stops and violent braking
Take care when driving on wet, icy , slippery or loose surfaces Slow down at corners, doorways, and at danger spots
Sound the horn several times when approaching blind corners, exits and entrances
Switch off and remove the key before leaving the forklift. Place the key in a safe location when driving task is completed
Apply the parking brake before leaving the forklift
Report any accidents or near misses to a supervisor
Park the forklift in a safe place, on level ground; never on a slope
Leave the forklift with the mast tilted forwards and the forks fully lowered, with the tips on the floor
Apply the parking brake, select neutral, switch off the engine and remove the key
Return keys or other activating devices to their place of safe-keeping
Report any malfunctions or defects immediately to a supervisor.
Assess the load before lifting. Check weight, size, load centre and security
Make sure that pallets are in good condition
Observe floor loading limits & Travel slowly when going down slopes
Find out the weight of the laden forklift
Check safe working load (SWL) of racking before placing loads onto it
Make sure load does not obstruct view. If it does, drive in reverse, looking in direction.
Make sure there is adequate clearance for the forklift and load, including overhead
Make sure the load is stable, Carry the load as close to ground as possible, Use controls smoothly & arms are fully inserted when travelling with a load
Position forks properly and as widely as possible
Make sure the fork Make sure the forklift is stopped before raising the load
Use suitable attachments for lifting unusual or wide loads
Ensure the forks face uphill when travelling up or down slopes with a load
Ensure the forks face downhill when travelling up or down slopes without a load
Adjust the tilt (where fitted) to suit the gradient and raise the forks to clear the ground
Line Of Fire.pptx
Construction workers face a wide variety of hazards that can result in injury or death if proper precautions are not taken. Simple precautions can help avoid injuries from being in the "line of fire" of hazards such as heavy machinery, falling objects, welding sparks, and more. It is everyone's responsibility on a construction site to be aware of potential lines of fire, remain vigilant of changing work environments, and use appropriate protective equipment and safety measures.
Lifting plan
This document provides a crane lifting plan and risk assessment for a lifting operation. It details the crane and lift information, including load details, lifting tackle, and crane setup procedures. Safety procedures are outlined, such as conducting a site inspection, briefing personnel, establishing communication methods, and following weather restrictions. Personnel qualifications and roles are defined. The plan is intended to ensure the lifting operation is carried out safely in compliance with relevant standards and regulations.
HSE-INDUCTION-TRAINING.ppt
This document provides an overview of safety policies and procedures for Fairdeal QHSE. It defines key safety terms and outlines responsibilities for management, supervisors, and employees to ensure a safe work environment and prevent accidents. Specific safety topics covered include personal protective equipment, housekeeping, electrical safety, fire prevention, lifting techniques, confined spaces, and prohibited behaviors. Management is responsible for training and safety compliance, while employees must follow safety rules and report any issues or injuries. Non-compliance may result in disciplinary actions up to termination.
Overhead Crane
The document provides safety guidelines for operating overhead cranes and hoists. It states that equipment must be inspected daily for wear and damage before use. Operators should warn others to stay clear of lifted loads and never allow anyone to ride the hook or load. Loads should be lifted smoothly and directly below the hoist, and brakes should be tested when lifting near maximum capacity. Cranes should never be left unattended while loads are suspended.
Working at-height
The document defines work at height as any work performed 1.8 meters or more above ground level, including below ground. Work above 1.8 meters requires a permit and safety checklist. Fall distances increase rapidly with time, emphasizing the need for fall protection like railings, safety harnesses attached to lifelines, and safety nets. Proper planning, equipment, and rescue procedures are required for working at heights.
Forklift safety
This document provides guidance on the safe operation of forklifts and other powered industrial trucks (PITs). It covers topics such as common forklift accident types, injuries and fatalities. It defines PITs and describes the seven common classes. It provides details on load capacity, stability, driving on inclines, tipping hazards, and inspection/maintenance. Proper procedures are outlined for refueling, charging, and what to do in a tip over situation. The importance of training, following safety procedures, and using seatbelts is emphasized throughout.
Night work safety
Arrangements for management of the different conditions brought about by night works or what assessments will be undertaken to ensure this can be conducted safely. Detail should also include shift patterns and management of worker fatigue.
Working at night poses a serious safety risk for
highway & construction workers. Those who work
at night are at a higher risk for injury because of:
• Reduced visibility for Equipment and other
vehicle drivers.
• Reduced visibility for workers.
• Lack of communication between shifts
• Increased number of impaired or drowsy drivers
• Sleep deprivation for workers
Rigger signalman handbook
This is really good document for newcomers of the engineering. Especially, which the people of the construction industry.
Lifting Operation Safety ppt.pptx
This document discusses safe lifting practices and requirements. It defines routine and non-routine lifts and lists potential hazards. Key requirements include developing a lifting plan, appointing competent supervisors, inspecting equipment, and defining roles for crane operators, riggers, and signal persons. Specific safe practices are outlined for preparing loads, attaching slings, and storing/maintaining equipment. Personnel must be trained and lifts must not endanger workers or exceed equipment ratings.
Material Handling Training by OSHA
This document provides information on material handling safety. It discusses manual material handling such as lifting and carrying, machine material handling using forklifts, and associated injuries. Hazards of improper lifting, struck by injuries, and forklift rollovers are covered. Safe lifting techniques, use of personal protective equipment, training requirements, and forklift safety checklists are also summarized.
Near miss
Near Miss are warning that some one is not doing his job properly, the only difference between an accident and near miss is LUCK
Presentation working at height
Working at height remains a major cause of injuries and fatalities. Employers must properly plan work at height, use the right equipment, and provide fall protection training to competent workers. Simple precautions like performing work from ladders safely and avoiding fragile surfaces can reduce risks. Workers should avoid working at unprotected heights whenever possible.
Working at heights
The document provides an overview of safety procedures for working at heights. It discusses ladder safety, fall protection equipment like harnesses and lanyards, scaffolding safety, and mobile elevated work platforms. It emphasizes the importance of fall protection, noting that falls are the leading cause of construction fatalities and that workers should be protected from falls of 2 meters or more.
Working at height slides
The document provides information about working at heights training, including:
- The aims are to provide personnel working at heights with practical knowledge and application of safe practices to prevent injury.
- The objectives include identifying fall regulations and risks, demonstrating safety equipment use, and emergency response procedures.
- It discusses examples of working at heights, regulations and responsibilities to control fall risks, and the goals of reducing falls injuries.
Risk assessment for testing & commissioning of cranes
Overhead crane, crane safety, lifting operation, EHS, Safety, Testing of Crane, Commissioning of Cranes,
for soft copy please email me at dawoodibrar@hotmail.com
Permit to Work Training
A work permit document outlines the type of work, location, equipment, time required, hazards, and safety precautions for a task. There are various types of work permits including hot work, cold work, chemical/acid work, work at height, excavation, electrical, confined space, vehicular/earthmoving equipment, and radiology permits. Hot work permits cover tasks involving heat, fire or sparks like welding, cutting, drilling, grinding, and sandblasting. Each task outlines its hazards like burns, sparks, fumes, and required safety equipment like fire extinguishers, protective clothing, ventilation and more.
Work at height safety
Fall hazard means a circumstance that exposes a worker in a workplace to a risk of a fall that is reasonably likely to cause injury to the worker or other person.
Assessing risks from working at height.
Common Fall Hazards at construction site.
Common Scaffold Hazards.
PERSONAL FALL PROTECTION.
Travel-Restraint Systems.
Fall-Arrest Systems.
Lifelines.
Scaffolding, also called scaffold or staging, is a temporary structure used to support a work crew and materials to aid in the construction, maintenance and repair of buildings, bridges and all other man made structures.
Compressed gas safety
This document provides information on the safe use, handling, and storage of compressed gases. It discusses regulations, properties of different types of gases, gas behavior, container markings, and emergency response. Key points covered include definitions of compressed, liquefied, and cryogenic gases; gas laws; hazard classifications; and regulations from organizations like OSHA, NFPA, and SDS. Color codes and markings are important for identifying gas types and ensuring safety.
Fire extingusher
The document provides information on fire safety and fire extinguisher training. It discusses the fire triangle, fuel classifications, and the different types of fire extinguishers including water, carbon dioxide, and dry chemical extinguishers. It explains how to identify the appropriate extinguisher based on the fuel source and use the PASS method of pulling the pin, aiming at the base of the fire, squeezing the handle, and sweeping from side to side. Rules for fighting fires safely are also outlined.
More Related Content
What's hot
Permit to work system
What is Permit to work system?
What are the requirements of permit to work?
Different types of permit to work system such electrical, hot and cold work etc.
Health And Safety Induction Training
This document outlines health and safety topics covered in an induction training. It discusses hazards associated with working at heights, proper use of ladders and scaffolding, fall protection, machine safety, chemical hazards, traffic safety, fire safety, and more. Safety signage and their meanings are explained. Penalties for safety infractions are listed to encourage compliance with safety rules and regulations. The goal is to educate workers on best practices to avoid accidents and injuries on the jobsite.
FORKLIFT SAFETY
Forklifts are extremely useful workplace vehicles, as long as they are used safely and appropriately by operators who are appropriately trained and competent to use them.
Forklifts can be dangerous: they account for 25% of injuries at work. Many workplace accidents involve people being hit or run over by forklift trucks (typically when the forklift is reversing) because the driver did not see them. Owing to their size and weight, injuries resulting from forklifts are generally very serious. Accidents involving them are often caused by poor supervision and a lack of training.
Always:
Wear appropriate personal protective clothing as provided by employer. Hard hat, protective footwear and high visibility clothing are recommended as a minimum when working around forklifts. Other equipment may be needed depending on the working environment
Report defects immediately to supervisor
Make sure work path is free of obstructions
Wear operator restraints, where fitted
Look all around before moving off
Look in the direction of travel
Avoid sudden stops and violent braking
Take care when driving on wet, icy , slippery or loose surfaces Slow down at corners, doorways, and at danger spots
Sound the horn several times when approaching blind corners, exits and entrances
Switch off and remove the key before leaving the forklift. Place the key in a safe location when driving task is completed
Apply the parking brake before leaving the forklift
Report any accidents or near misses to a supervisor
Park the forklift in a safe place, on level ground; never on a slope
Leave the forklift with the mast tilted forwards and the forks fully lowered, with the tips on the floor
Apply the parking brake, select neutral, switch off the engine and remove the key
Return keys or other activating devices to their place of safe-keeping
Report any malfunctions or defects immediately to a supervisor.
Assess the load before lifting. Check weight, size, load centre and security
Make sure that pallets are in good condition
Observe floor loading limits & Travel slowly when going down slopes
Find out the weight of the laden forklift
Check safe working load (SWL) of racking before placing loads onto it
Make sure load does not obstruct view. If it does, drive in reverse, looking in direction.
Make sure there is adequate clearance for the forklift and load, including overhead
Make sure the load is stable, Carry the load as close to ground as possible, Use controls smoothly & arms are fully inserted when travelling with a load
Position forks properly and as widely as possible
Make sure the fork Make sure the forklift is stopped before raising the load
Use suitable attachments for lifting unusual or wide loads
Ensure the forks face uphill when travelling up or down slopes with a load
Ensure the forks face downhill when travelling up or down slopes without a load
Adjust the tilt (where fitted) to suit the gradient and raise the forks to clear the ground
Line Of Fire.pptx
Construction workers face a wide variety of hazards that can result in injury or death if proper precautions are not taken. Simple precautions can help avoid injuries from being in the "line of fire" of hazards such as heavy machinery, falling objects, welding sparks, and more. It is everyone's responsibility on a construction site to be aware of potential lines of fire, remain vigilant of changing work environments, and use appropriate protective equipment and safety measures.
Lifting plan
This document provides a crane lifting plan and risk assessment for a lifting operation. It details the crane and lift information, including load details, lifting tackle, and crane setup procedures. Safety procedures are outlined, such as conducting a site inspection, briefing personnel, establishing communication methods, and following weather restrictions. Personnel qualifications and roles are defined. The plan is intended to ensure the lifting operation is carried out safely in compliance with relevant standards and regulations.
HSE-INDUCTION-TRAINING.ppt
This document provides an overview of safety policies and procedures for Fairdeal QHSE. It defines key safety terms and outlines responsibilities for management, supervisors, and employees to ensure a safe work environment and prevent accidents. Specific safety topics covered include personal protective equipment, housekeeping, electrical safety, fire prevention, lifting techniques, confined spaces, and prohibited behaviors. Management is responsible for training and safety compliance, while employees must follow safety rules and report any issues or injuries. Non-compliance may result in disciplinary actions up to termination.
Overhead Crane
The document provides safety guidelines for operating overhead cranes and hoists. It states that equipment must be inspected daily for wear and damage before use. Operators should warn others to stay clear of lifted loads and never allow anyone to ride the hook or load. Loads should be lifted smoothly and directly below the hoist, and brakes should be tested when lifting near maximum capacity. Cranes should never be left unattended while loads are suspended.
Working at-height
The document defines work at height as any work performed 1.8 meters or more above ground level, including below ground. Work above 1.8 meters requires a permit and safety checklist. Fall distances increase rapidly with time, emphasizing the need for fall protection like railings, safety harnesses attached to lifelines, and safety nets. Proper planning, equipment, and rescue procedures are required for working at heights.
Forklift safety
This document provides guidance on the safe operation of forklifts and other powered industrial trucks (PITs). It covers topics such as common forklift accident types, injuries and fatalities. It defines PITs and describes the seven common classes. It provides details on load capacity, stability, driving on inclines, tipping hazards, and inspection/maintenance. Proper procedures are outlined for refueling, charging, and what to do in a tip over situation. The importance of training, following safety procedures, and using seatbelts is emphasized throughout.
Night work safety
Arrangements for management of the different conditions brought about by night works or what assessments will be undertaken to ensure this can be conducted safely. Detail should also include shift patterns and management of worker fatigue.
Working at night poses a serious safety risk for
highway & construction workers. Those who work
at night are at a higher risk for injury because of:
• Reduced visibility for Equipment and other
vehicle drivers.
• Reduced visibility for workers.
• Lack of communication between shifts
• Increased number of impaired or drowsy drivers
• Sleep deprivation for workers
Rigger signalman handbook
This is really good document for newcomers of the engineering. Especially, which the people of the construction industry.
Lifting Operation Safety ppt.pptx
This document discusses safe lifting practices and requirements. It defines routine and non-routine lifts and lists potential hazards. Key requirements include developing a lifting plan, appointing competent supervisors, inspecting equipment, and defining roles for crane operators, riggers, and signal persons. Specific safe practices are outlined for preparing loads, attaching slings, and storing/maintaining equipment. Personnel must be trained and lifts must not endanger workers or exceed equipment ratings.
Material Handling Training by OSHA
This document provides information on material handling safety. It discusses manual material handling such as lifting and carrying, machine material handling using forklifts, and associated injuries. Hazards of improper lifting, struck by injuries, and forklift rollovers are covered. Safe lifting techniques, use of personal protective equipment, training requirements, and forklift safety checklists are also summarized.
Near miss
Near Miss are warning that some one is not doing his job properly, the only difference between an accident and near miss is LUCK
Presentation working at height
Working at height remains a major cause of injuries and fatalities. Employers must properly plan work at height, use the right equipment, and provide fall protection training to competent workers. Simple precautions like performing work from ladders safely and avoiding fragile surfaces can reduce risks. Workers should avoid working at unprotected heights whenever possible.
Working at heights
The document provides an overview of safety procedures for working at heights. It discusses ladder safety, fall protection equipment like harnesses and lanyards, scaffolding safety, and mobile elevated work platforms. It emphasizes the importance of fall protection, noting that falls are the leading cause of construction fatalities and that workers should be protected from falls of 2 meters or more.
Working at height slides
The document provides information about working at heights training, including:
- The aims are to provide personnel working at heights with practical knowledge and application of safe practices to prevent injury.
- The objectives include identifying fall regulations and risks, demonstrating safety equipment use, and emergency response procedures.
- It discusses examples of working at heights, regulations and responsibilities to control fall risks, and the goals of reducing falls injuries.
Risk assessment for testing & commissioning of cranes
Overhead crane, crane safety, lifting operation, EHS, Safety, Testing of Crane, Commissioning of Cranes,
for soft copy please email me at dawoodibrar@hotmail.com
Permit to Work Training
A work permit document outlines the type of work, location, equipment, time required, hazards, and safety precautions for a task. There are various types of work permits including hot work, cold work, chemical/acid work, work at height, excavation, electrical, confined space, vehicular/earthmoving equipment, and radiology permits. Hot work permits cover tasks involving heat, fire or sparks like welding, cutting, drilling, grinding, and sandblasting. Each task outlines its hazards like burns, sparks, fumes, and required safety equipment like fire extinguishers, protective clothing, ventilation and more.
Work at height safety
Fall hazard means a circumstance that exposes a worker in a workplace to a risk of a fall that is reasonably likely to cause injury to the worker or other person.
Assessing risks from working at height.
Common Fall Hazards at construction site.
Common Scaffold Hazards.
PERSONAL FALL PROTECTION.
Travel-Restraint Systems.
Fall-Arrest Systems.
Lifelines.
Scaffolding, also called scaffold or staging, is a temporary structure used to support a work crew and materials to aid in the construction, maintenance and repair of buildings, bridges and all other man made structures.
What's hot (20)
Risk assessment for testing & commissioning of cranes
Risk assessment for testing & commissioning of cranes
Viewers also liked
Compressed gas safety
This document provides information on the safe use, handling, and storage of compressed gases. It discusses regulations, properties of different types of gases, gas behavior, container markings, and emergency response. Key points covered include definitions of compressed, liquefied, and cryogenic gases; gas laws; hazard classifications; and regulations from organizations like OSHA, NFPA, and SDS. Color codes and markings are important for identifying gas types and ensuring safety.
Fire extingusher
The document provides information on fire safety and fire extinguisher training. It discusses the fire triangle, fuel classifications, and the different types of fire extinguishers including water, carbon dioxide, and dry chemical extinguishers. It explains how to identify the appropriate extinguisher based on the fuel source and use the PASS method of pulling the pin, aiming at the base of the fire, squeezing the handle, and sweeping from side to side. Rules for fighting fires safely are also outlined.
Lpg gas safety rules
The document summarizes the Railroad Commission of Texas' LP-Gas Safety Rules, which apply to the design, construction, location, and operation of LP-gas systems and equipment in Texas. The rules are divided into subchapters covering general requirements, installations/containers/equipment, vehicles/dispensers, and the adoption of national fuel gas codes with additional Texas requirements. Key aspects addressed include licensing, training, inspections, safety compliance, and enforcement.
Safety work instruction for compressed gas
This document provides safety guidelines for working with compressed gases. It states that all compressed gas cylinders should be handled carefully and according to the specific gas's properties. Damaged cylinders should be inspected before use. Gases are identified by color (red for flammable, green for non-flammable) and labeling. Proper transportation, storage, connection, and use of regulators are outlined to prevent leaks, explosions, and other accidents. Personnel should be aware of each gas's hazards like flammability, toxicity, and corrosiveness. Overall, the document aims to promote safe practices for compressed gas handling.
Gas cylinder safety
Compressed gas cylinders require careful handling and storage due to the multiple hazards they present. Three key safety procedures for working with compressed gas cylinders are: securely storing cylinders to prevent tipping, clearly identifying cylinder contents to avoid mixing incompatible gases, and carefully checking all cylinder valves and connections for leaks using soap solutions before opening cylinder valves.
Chapter 13
The document discusses emergency incident management and the Incident Command System (ICS). It explains that the ICS provides a standardized approach to the command, control, and coordination of emergency incidents, allowing responders from different agencies and jurisdictions to work together. The ICS establishes common terminology, organizational structure, and management processes to effectively address incidents of any size or complexity. The strategic priorities for incident response are rescue, exposures, confinement, extinguishment, overhaul, salvage, and ventilation.
Design and safety_handbook_3001.5
This document provides an overview of compressed gas safety, including:
1) It defines different categories of gases such as asphyxiant, corrosive, cryogenic, flammable, inert, oxidant, pyrophoric, and toxic gases and provides examples and safety considerations for each.
2) It includes a table listing common specialty gases and categorizing them as flammable, liquefied, having oxidant, inert, corrosive, or toxic properties.
3) The document emphasizes the importance of understanding gas properties and following proper safety precautions when working with compressed gases due to their flammable, toxic, corrosive, and other hazardous nature.
Central gas equipment for industrial gases (2011 edition in english) uk619 10...
The document provides information about gas supply equipment for industrial installations, including central gas manifolds. It discusses the advantages of central gas systems such as improved safety, efficiency and cost savings. Central gas manifolds allow for continuous gas supply to work stations from one location, reducing transportation of gas cylinders within the workplace. The document also outlines requirements for gas installations including engineering according to relevant laws and regulations, applying for necessary permits, and conducting a risk analysis.
How to detect fake lpg cylinder
This document provides information on how to detect fake LPG cylinders and safely use genuine cylinders. It outlines that LPG cylinders should be properly marked by the manufacturer with their name and address. It also lists safety precautions like ensuring cylinders are turned off before disconnecting and closing the regulator when not in use. The document advises what to do in case of an LPG leak, like stopping operations and isolating the supply. It provides a website link for more details on detecting fake LPG cylinders.
OHS Accidents
This document provides an overview of accident prevention. It defines key terms like accident, hazard, risk, and safety. It discusses the causes of accidents including management factors, environmental factors, equipment factors, and human behavior factors. It also examines theories of human behavior and strategies for changing unsafe behaviors. The document emphasizes that an effective accident prevention program requires a written plan, safety orientation for employees, and safety meetings or a safety committee to engage employees.
Personal HSE commitments
This document outlines an individual's personal health, safety, and environment commitments including not using a mobile phone while driving, using correct safety equipment at home and during sports, and regular exercise. It also lists internal commitments such as ensuring one's team follows their own HSE commitments, focusing on HSE in meetings, and taking time to discuss HSE when visiting operations. External commitments include participating in client HSE seminars and communicating HSE commitments.
Catalogue for LPG-parts and LPG conversion kits
All parts you need to convert your car to LPG. In our catalogue you can find all spare parts for the moste popular brands of LPG kit manufacturers from Europe. We keep over 500,000 parts, ready for next day delivery all over Europe.
Hse oil and gas management services
The document discusses new safety and environmental management system (SEMS) regulations introduced by the Bureau of Safety and Environmental Enforcement in response to the 2010 Deepwater Horizon oil spill, noting that Lloyd's Register can help energy companies comply with the new rules through services like auditing SEMS, conducting hazard analyses, and establishing management of change procedures.
Enform oil and gas safety: Process safey vs. personal safety
Process safety focuses on preventing catastrophic accidents associated with hazardous materials, while personal safety focuses on preventing workplace injuries. Process safety concerns low probability, high consequence events like explosions, whereas personal safety addresses more frequent, lower impact incidents like slips and falls. Process safety requires technical expertise to identify major hazard risks and implement controls like engineering solutions. It also demands buy-in from senior management. The goal of process safety is to protect people, property and the environment from rare but severe incidents, while personal safety aims to prevent a series of minor incidents. Both areas are important, and their management systems have considerable overlap.
Smart LPG System
In this presentation, Jithin presents an innovative idea that will solve the problem of booking LPG cylinders in time. Jithin's proposed system can be integrated with the online system that is currently available.
Automation
In this presentation, Shivam introduces automation and associated trends. Shivam is interested in home automation.
Transhumanist Declaration
The visions and guidelines of the international Transhumanist movement. This is a global network that advocates and supports the safe and responsible development and application of innovations and new technologies for improving the human condition.
The Transhumanist Declaration was originally crafted in 1998 by an international group of authors: Doug Baily, Anders Sandberg, Gustavo Alves, Max More, Holger Wagner, Natasha Vita-More, Eugene Leitl, Bernie Staring, David Pearce, Bill Fantegrossi, den Otter, Ralf Fletcher, Kathryn Aegis, Tom Morrow, Alexander Chislenko, Lee Daniel Crocker, Darren Reynolds, Keith Elis, Thom Quinn, Mikhail Sverdlov, Arjen Kamphuis, Shane Spaulding, and Nick Bostrom. This Transhumanist Declaration has been modified over the years by several authors and organizations. It was adopted by the Humanity+ Board in March, 2009.
Watch as video at: http://www.youtube.com/watch?v=9a3GU6Vv1Rg
Fresh vegetable-and-fruit-juices-by-norman-walker درمان با آب میوه ها و آب سب...
This document provides information about Dr. Norman W. Walker and his research on fresh vegetable and fruit juices. It discusses how cooking destroys enzymes and nutrients in foods, and that juicing allows the body to more easily digest and absorb minerals, salts, and vitamins. It emphasizes that a diet of raw vegetables and fresh juices is important for nourishment and maintaining health.
[Harry edmar]hydrodynamics concepts and experiments
This chapter develops a coupled fluid-structure model to simulate the interaction between water flow and a flexible fishing net. The model combines a porous media fluid model and a lumped-mass mechanical model. The porous media fluid model uses the Navier-Stokes equations to simulate flow around a rigid net, while the lumped-mass model simulates net deformation. An iterative scheme is used to solve for the steady fluid-net interaction. The model aims to better understand hydrodynamic forces on nets and flow patterns, which has significance for net cage and aquaculture design.
Viewers also liked (20)
Central gas equipment for industrial gases (2011 edition in english) uk619 10...
Central gas equipment for industrial gases (2011 edition in english) uk619 10...
Enform oil and gas safety: Process safey vs. personal safety
Enform oil and gas safety: Process safey vs. personal safety
Fresh vegetable-and-fruit-juices-by-norman-walker درمان با آب میوه ها و آب سب...
Fresh vegetable-and-fruit-juices-by-norman-walker درمان با آب میوه ها و آب سب...
[Harry edmar]hydrodynamics concepts and experiments
[Harry edmar]hydrodynamics concepts and experiments
More from Reliance
Excavation & Trenching Safety
This PPT contains
OHS Act and Regulation Requirements
Trenching Inspection and Protection
Underground Utilities
Personal Protective Equipment
PPE's is the last Hierarchy of Controls , but It will worn before you entry on your Work site , This PPT give you good awareness about PPE's
Confined space-entry
Many workers are injured and killed each year while working in confined spaces. An estimated 60% of the fatalities have been among the would-be rescuers. A confined space can be more hazardous than regular workspaces for many reasons. To effectively control the risks associated with working in a confined space, a Confined Space Hazard Assessment and Control Program should be implemented for your workplace. Before watching this PPT , make sure to review the specific regulations that apply to your workplace
Hydrogen sulfide
The document provides training goals and information about hydrogen sulfide (H2S) gas for employees who may be exposed. It aims to develop knowledgeable employees and provide consistent industry training. H2S is a toxic, flammable gas that is colorless and smells like rotten eggs. It can be fatal even at low concentrations and proper safety equipment and procedures must be followed when exposure is possible.
House Keeping & 5 S
House keeping is a very big part of our each and every job , this slide give you very good awareness about house keeping and Japanese 5 "S" Method ..
Bhopal gas tragedy
The Bhopal disaster occurred in 1984 when toxic gas leaked from a pesticide plant in Bhopal, India owned by Union Carbide, exposing over 500,000 people. At least 20,000 died and over 120,000 continue to suffer health effects. The gas was methyl isocyanate, which was stored in tanks at the plant. While the exact cause is still debated, it is believed a reaction occurred when water entered a tank containing the chemical. The leak exposed a large population due to lapses in safety systems and emergency planning by both the company and local government. An alternative production process has been suggested that would not require storage or use of dangerous chemicals like methyl isocyanate.
Safe Material Handling
Material Handling accidents are growing our industries , it's main reason is untrained people , over confidence , working pressure etc , This PPT make very good training material ...
Material Safety Data Sheet
The document discusses the key sections of a Material Safety Data Sheet (MSDS), which provides information on the properties and potential hazards of chemicals. An MSDS includes 16 sections that cover identification of the chemical/mixture and supplier; hazards; composition; first aid measures; firefighting measures; accidental release measures; handling and storage; exposure controls and personal protection; physical and chemical properties; stability and reactivity; toxicological information; ecological information; disposal considerations; transport information; and other information such as regulatory information. The MSDS provides important information to ensure chemicals are handled safely.
Blood donation
The document discusses blood and blood donation. It notes that blood has four main components - red blood cells, white blood cells, platelets, and plasma. It provides information on whole blood donation, platelet donation, and double red cell donation, including eligibility requirements and the donation process. The document emphasizes that blood donation saves lives by providing blood products to hospital patients in need of surgery or treatment.
Fire & safety
Fire safety document discusses fire hazards and risk assessment. It defines risk as the uncertainty of an unforeseen event occurring and outlines factors like magnitude of consequences and likelihood of occurrence. It also discusses the ALARP principle which states that risks are only tolerable if all reasonably practicable measures have been taken to reduce them. The document further examines hazards like vapour cloud explosions and fires as well as classification of fires and suitable extinguishing methods.
How to Prevent Heart attack ?????
We are facing lot of health issues daily . because Our new life style Food , Smoking , use of Alcohol , Stress etc , A heart attack happens when the flow of oxygen-rich blood to a section of heart muscle suddenly becomes blocked and the heart can't get oxygen. If blood flow isn't restored quickly, the section of heart muscle begins to die.
Heart attacks are a leading killer of both men and women . This Slides Explain How to Prevent Heart attack .
Factories act 1948
This slides Easily give you awareness about Factories Act 1948 . if you like my slides plz give comments and likes
Insulation job hazards & Precautions
Insulation Job is done every industry But no one know about Actual Insulation job hazards and precautions . This slides explain the insulation job Hazards & precautions , type of insulation etc ..
First Aid Training
First aid is the immediate help given to the victim of an accident or sudden illness, before medical help is obtained.
Know More about First Aid
Usage of Personal Protective Equipment
PPE is used to reduce or minimize the exposure or contact to injurious physical, chemical, ergonomic, or biological agents. A hazard cannot be eliminated by PPE, but the risk of injury can be reduced. this slide show explain How to Use PPE's
Electrical Safety
This PPT very useful to industrial safety person for give training about electrical Safety . it contain electrical job hazards and precautions .
Chemcial handling
This document provides an overview of chemical hazards and safety. It discusses the classification of workplace hazards including physical, chemical, biological and ergonomic. It defines key terms like flash point, auto ignition temperature, threshold limit values and IDLH. It describes routes of chemical entry, health effects of chemicals on different organs, and carcinogens. The document provides guidance on personal protective equipment, respiratory protection, and controlling chemical exposure through engineering controls, hygiene and proper storage. It emphasizes the importance of material safety data sheets and following standard operating procedures to safely handle chemicals.
GLOBAL ENVIRONMENTAL ISSUES AND SUSTAINABLE DEVELOPMENT
The document discusses several global environmental issues and sustainable development. It defines sustainable development as meeting present needs without compromising future generations. It then summarizes key information on the biosphere, atmosphere, hydrosphere and land. It also provides details on important environmental issues like ozone depletion caused by CFCs, global climate change driven by greenhouse gases, and sea level rise from melting ice sheets. Sustainable development challenges include population growth, resource use, pollution control and meeting increasing food demands.
More from Reliance (18)
GLOBAL ENVIRONMENTAL ISSUES AND SUSTAINABLE DEVELOPMENT
GLOBAL ENVIRONMENTAL ISSUES AND SUSTAINABLE DEVELOPMENT
Recently uploaded
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
The smart irrigation system represents an innovative approach to optimize water usage in agricultural and landscaping practices. The integration of cutting-edge technologies, including sensors, actuators, and data analysis, empowers this system to provide accurate monitoring and control of irrigation processes by leveraging real-time environmental conditions. The main objective of a smart irrigation system is to optimize water efficiency, minimize expenses, and foster the adoption of sustainable water management methods. This paper conducts a systematic risk assessment by exploring the key components/assets and their functionalities in the smart irrigation system. The crucial role of sensors in gathering data on soil moisture, weather patterns, and plant well-being is emphasized in this system. These sensors enable intelligent decision-making in irrigation scheduling and water distribution, leading to enhanced water efficiency and sustainable water management practices. Actuators enable automated control of irrigation devices, ensuring precise and targeted water delivery to plants. Additionally, the paper addresses the potential threat and vulnerabilities associated with smart irrigation systems. It discusses limitations of the system, such as power constraints and computational capabilities, and calculates the potential security risks. The paper suggests possible risk treatment methods for effective secure system operation. In conclusion, the paper emphasizes the significant benefits of implementing smart irrigation systems, including improved water conservation, increased crop yield, and reduced environmental impact. Additionally, based on the security analysis conducted, the paper recommends the implementation of countermeasures and security approaches to address vulnerabilities and ensure the integrity and reliability of the system. By incorporating these measures, smart irrigation technology can revolutionize water management practices in agriculture, promoting sustainability, resource efficiency, and safeguarding against potential security threats.
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECT
The rivalry between prominent international actors for dominance over Central Asia's hydrocarbon
reserves and the ancient silk trade route, along with China's diplomatic endeavours in the area, has been
referred to as the "New Great Game." This research centres on the power struggle, considering
geopolitical, geostrategic, and geoeconomic variables. Topics including trade, political hegemony, oil
politics, and conventional and nontraditional security are all explored and explained by the researcher.
Using Mackinder's Heartland, Spykman Rimland, and Hegemonic Stability theories, examines China's role
in Central Asia. This study adheres to the empirical epistemological method and has taken care of
objectivity. This study analyze primary and secondary research documents critically to elaborate role of
china’s geo economic outreach in central Asian countries and its future prospect. China is thriving in trade,
pipeline politics, and winning states, according to this study, thanks to important instruments like the
Shanghai Cooperation Organisation and the Belt and Road Economic Initiative. According to this study,
China is seeing significant success in commerce, pipeline politics, and gaining influence on other
governments. This success may be attributed to the effective utilisation of key tools such as the Shanghai
Cooperation Organisation and the Belt and Road Economic Initiative.
[JPP-1] - (JEE 3.0) - Kinematics 1D - 14th May..pdf
Kinematics 11th jpp- 01. ( Solved ) unacademy namo kaul on 14th may...
Literature Review Basics and Understanding Reference Management.pptx
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
International Conference on NLP, Artificial Intelligence, Machine Learning an...
International Conference on NLP, Artificial Intelligence, Machine Learning and Applications (NLAIM 2024) offers a premier global platform for exchanging insights and findings in the theory, methodology, and applications of NLP, Artificial Intelligence, Machine Learning, and their applications. The conference seeks substantial contributions across all key domains of NLP, Artificial Intelligence, Machine Learning, and their practical applications, aiming to foster both theoretical advancements and real-world implementations. With a focus on facilitating collaboration between researchers and practitioners from academia and industry, the conference serves as a nexus for sharing the latest developments in the field.
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...University of Maribor
Slides from talk presenting:
Aleš Zamuda: Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapter and Networking.
Presentation at IcETRAN 2024 session:
"Inter-Society Networking Panel GRSS/MTT-S/CIS
Panel Session: Promoting Connection and Cooperation"
IEEE Slovenia GRSS
IEEE Serbia and Montenegro MTT-S
IEEE Slovenia CIS
11TH INTERNATIONAL CONFERENCE ON ELECTRICAL, ELECTRONIC AND COMPUTING ENGINEERING
3-6 June 2024, Niš, SerbiaAdvanced control scheme of doubly fed induction generator for wind turbine us...
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
ACEP Magazine edition 4th launched on 05.06.2024
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
Understanding Inductive Bias in Machine Learning
This presentation explores the concept of inductive bias in machine learning. It explains how algorithms come with built-in assumptions and preferences that guide the learning process. You'll learn about the different types of inductive bias and how they can impact the performance and generalizability of machine learning models.
The presentation also covers the positive and negative aspects of inductive bias, along with strategies for mitigating potential drawbacks. We'll explore examples of how bias manifests in algorithms like neural networks and decision trees.
By understanding inductive bias, you can gain valuable insights into how machine learning models work and make informed decisions when building and deploying them.
Modelagem de um CSTR com reação endotermica.pdf
Modelagem em função de transferencia. CSTR não-linear.
Recycled Concrete Aggregate in Construction Part III
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
Recently uploaded (20)
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
A SYSTEMATIC RISK ASSESSMENT APPROACH FOR SECURING THE SMART IRRIGATION SYSTEMS
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECT
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECT
ACRP 4-09 Risk Assessment Method to Support Modification of Airfield Separat...
ACRP 4-09 Risk Assessment Method to Support Modification of Airfield Separat...
[JPP-1] - (JEE 3.0) - Kinematics 1D - 14th May..pdf
[JPP-1] - (JEE 3.0) - Kinematics 1D - 14th May..pdf
Literature Review Basics and Understanding Reference Management.pptx
Literature Review Basics and Understanding Reference Management.pptx
BPV-GUI-01-Guide-for-ASME-Review-Teams-(General)-10-10-2023.pdf
BPV-GUI-01-Guide-for-ASME-Review-Teams-(General)-10-10-2023.pdf
International Conference on NLP, Artificial Intelligence, Machine Learning an...
International Conference on NLP, Artificial Intelligence, Machine Learning an...
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Recycled Concrete Aggregate in Construction Part III
Recycled Concrete Aggregate in Construction Part III
Horrible Crane accident , 2 people died include one safety officer in RIL Jamnagar
- 2. • Horrible Crane accident , 2 people died include one safety officer in RIL Jamnagar •Jamnagar Gujarat 29-06-2015 : Accident of crain at Reliance Jamnagr site Today . Reliance's 70 ton Crane Zoomlion in C2 complex area .One helper(crane operator helper ) taken this Crane and he didn't take care about out rigger of the crane , actually at the time of crane operation one side of out rigger didn't extend fully and also due to uneven ground condition and the while the material lifting crane has fell down on the near by container and people .... • only the one person(crane operator ) taken another 2 people life .... so plz plz don't do this type of high risk job with antonyms people (Following photos are very cruel . so if you don't want see please avoid it .. only see your own risk )