The document discusses various aspects of fuels and combustion. It defines fuels as combustible substances containing mainly carbon that produce large amounts of heat during combustion. The main sources of fuel are coal and petroleum, which are fossil fuels formed from ancient plant and animal remains. Key characteristics of good fuels include high calorific value, moderate ignition temperature, and low moisture and non-combustible content. Liquid fuels like petroleum and its products are easily stored, transported and have high energy density. The processes of fractional distillation and refining of petroleum are described to produce useful fuel fractions like gasoline, diesel and kerosene. Calorific values indicate the energy content of fuels and can be measured using bomb calorime
The document discusses fuels and combustion. It defines fuels and their classification based on occurrence and physical state. It describes the measurement of calorific value using a bomb calorimeter and Junkers gas calorimeter. It also discusses the gross and net calorific values, combustion calculations, proximate and ultimate analysis of solid fuels, and the theoretical calculation of a fuel's calorific value using Dulong's formula.
This document discusses various parameters that affect the performance of spark-ignition engines and their fuels. It covers topics like octane number, calorific value, antiknock characteristics, and methods to determine these properties through experiments. The key parameters discussed are octane number, which indicates a fuel's resistance to autoignition; calorific value, which represents a fuel's energy content; and factors like chemical composition, air-fuel ratio, and ignition timing that influence knocking. Methods to find these properties experimentally include using a bomb calorimeter or Junker's calorimeter.
Fuel is a combustible substance that generates heat when burned in the presence of oxygen. Carbon and hydrogen are the main constituents of fuel. Solid fuels include wood, peat, lignite, bituminous coal, anthracite coal, and artificial solid fuels like coke and pulverized coal. Liquid fuels come from crude petroleum and include gasoline, diesel, and kerosene. Gaseous fuels include natural gas, blast furnace gas, producer gas, and water gas. The calorific value is a measure of the heat generated during combustion and is higher for liquid and gaseous fuels compared to solid fuels. Bomb calorimetry and Junker's gas calorimetry are common experimental
This document defines fuels and classifies them as primary or secondary. It discusses the characteristics of good fuels and defines gross calorific value and net calorific value. It describes how to determine calorific values using bomb calorimetry and gas calorimetry through calculations involving the mass of fuel burned, water mass, temperature changes, and corrections. Specific solid, liquid and gaseous fuels are also listed along with the combustion of fuels.
The document discusses fuel types, water treatment processes, and heat transfer calculations. It describes the three main types of fuels as solid, liquid, and gaseous. It also outlines several water treatment steps including removal of suspensions, dissolved salts, minerals, and pathogens. Specific heat capacity and formulas for calculating heat requirements for various processes like heating food or water are provided.
method to find calorific values of fuelsAWAISCHUDHARY
This document discusses calorific values, which measure the heating power or energy content of fuels and foods. It defines lower and higher calorific values, and explains that calorific value depends on a substance's composition. Junker's calorimeter is used to specifically measure the calorific value of gases. The document also provides the formula to calculate higher calorific value from experimental measurements of mass, temperatures, and heat capacities in a bomb calorimeter test.
This document discusses fuels and their analysis. It defines fuels and their classification as primary/natural or secondary/derived and solid, liquid or gaseous. Characteristics of good fuels like high calorific value and low ash are presented. Methods to determine calorific value using bomb calorimeter and calculations are described. Coal analysis techniques of proximate analysis (moisture, volatile matter, ash, fixed carbon) and ultimate analysis (C,H,N,S,O) are explained. The significance of the analyses for commercial classification and process heat balances is highlighted.
The document discusses fuels and combustion. It defines fuels and their classification based on occurrence and physical state. It describes the measurement of calorific value using a bomb calorimeter and Junkers gas calorimeter. It also discusses the gross and net calorific values, combustion calculations, proximate and ultimate analysis of solid fuels, and the theoretical calculation of a fuel's calorific value using Dulong's formula.
This document discusses various parameters that affect the performance of spark-ignition engines and their fuels. It covers topics like octane number, calorific value, antiknock characteristics, and methods to determine these properties through experiments. The key parameters discussed are octane number, which indicates a fuel's resistance to autoignition; calorific value, which represents a fuel's energy content; and factors like chemical composition, air-fuel ratio, and ignition timing that influence knocking. Methods to find these properties experimentally include using a bomb calorimeter or Junker's calorimeter.
Fuel is a combustible substance that generates heat when burned in the presence of oxygen. Carbon and hydrogen are the main constituents of fuel. Solid fuels include wood, peat, lignite, bituminous coal, anthracite coal, and artificial solid fuels like coke and pulverized coal. Liquid fuels come from crude petroleum and include gasoline, diesel, and kerosene. Gaseous fuels include natural gas, blast furnace gas, producer gas, and water gas. The calorific value is a measure of the heat generated during combustion and is higher for liquid and gaseous fuels compared to solid fuels. Bomb calorimetry and Junker's gas calorimetry are common experimental
This document defines fuels and classifies them as primary or secondary. It discusses the characteristics of good fuels and defines gross calorific value and net calorific value. It describes how to determine calorific values using bomb calorimetry and gas calorimetry through calculations involving the mass of fuel burned, water mass, temperature changes, and corrections. Specific solid, liquid and gaseous fuels are also listed along with the combustion of fuels.
The document discusses fuel types, water treatment processes, and heat transfer calculations. It describes the three main types of fuels as solid, liquid, and gaseous. It also outlines several water treatment steps including removal of suspensions, dissolved salts, minerals, and pathogens. Specific heat capacity and formulas for calculating heat requirements for various processes like heating food or water are provided.
method to find calorific values of fuelsAWAISCHUDHARY
This document discusses calorific values, which measure the heating power or energy content of fuels and foods. It defines lower and higher calorific values, and explains that calorific value depends on a substance's composition. Junker's calorimeter is used to specifically measure the calorific value of gases. The document also provides the formula to calculate higher calorific value from experimental measurements of mass, temperatures, and heat capacities in a bomb calorimeter test.
This document discusses fuels and their analysis. It defines fuels and their classification as primary/natural or secondary/derived and solid, liquid or gaseous. Characteristics of good fuels like high calorific value and low ash are presented. Methods to determine calorific value using bomb calorimeter and calculations are described. Coal analysis techniques of proximate analysis (moisture, volatile matter, ash, fixed carbon) and ultimate analysis (C,H,N,S,O) are explained. The significance of the analyses for commercial classification and process heat balances is highlighted.
This document discusses the fundamentals of fuels, including their classification, calorific value, and analysis. It begins by defining what a fuel is and providing examples. It then covers:
- Classification of fuels into primary/natural and secondary/derived types.
- Calorific value and different units used to measure heat such as calories, kilocalories, BTUs. It defines gross/higher and lower/net calorific values.
- Methods of determining calorific value using a bomb calorimeter, involving burning a fuel sample and calculating the heat released based on temperature changes.
- Proximate analysis of coal to determine moisture, volatile matter, ash, and fixed carbon content.
Petroleum is a mixture of hydrocarbons that can be separated into fractions by fractional distillation based on differences in boiling points. The top five crude oil producing countries are Saudi Arabia, Russia, the United States, Iran, and China. Petroleum is heated to 360°C in the absence of air during oil refining to vaporize it before fractional distillation, in order to prevent ignition and potential explosions.
Fuel is a combustible substance, containing carbon as main constituent, which...drmanojkarar
Energy resources: While selecting an ideal fuel for domestic or industrial purpose we should keep in mind that the fuel selected must possess the following characteristic properties.
1) It should possess high calorific value.
2) It should have proper ignition temperature. The ignition temperature of the fuel should neither be too low nor too high.
3) It should not produce poisonous products during combustion. In other words, it should not cause pollution o combustion.
4) It should have moderate rate of combustion.
5) Combustion should be easily controllable i.e., combustion of fuel should be easy to start or stop as and when required.
6) It should not leave behind much ash on combustion.
7) It should be easily available in plenty.
8) It should have low moisture content.
9) It should be cheap.
10) It should be easy to handle and transport.
Calorific value: It is defined as the total amount of heat liberated, when unit mass or unit volume of the fuel is completely burnt in air or oxygen.
Units of heat:
a) Calorie: The amount of heat required to increase the temperature of 1 gm of water through one degree centigrade.
b) Kilocalorie: It is equal to 1000 calories. The quantity of heat required to rise the temperature of 1 Kg of water through one degree centigrade.
1 K.cal = 1000 cals
c) British thermal unit (B.Th.U.): The quantity of heat required to rise the temperature of 1 pound of water through one degree Farenheit.
1 B.Th.U = 252 cals = 0.252 K.cal
d) Centigrade heat unit (C.H.U): The quantity of heat required to rise the temperature of one pound of water through one degree centigrade.
1 K. cal = 3.968 B.Th.U = 2.2 C.H.U
For solids or liquid fuel: Calorie/gm (cal/gm) (or) Kilocalorie/Kg (K.cal/Kg) (or) B.Th.U/lb
For gaseous fuels: Kilocalorie/cubic meter (K.cal/m3) (or) B.Th.U/ft3
the slides explain about fuel and combustionrndfme
The document discusses different types of fuels and combustion. It provides classifications of fuels as primary, secondary, solid, liquid, and gaseous. It defines calorific value and explains gross calorific value and net calorific value. The document discusses solid fuels like coal, its classification and analysis including proximate analysis and ultimate analysis. It explains the importance of these analyses. It also discusses the production of metallurgical coke and its required properties.
Fuels are substances that readily combine with oxygen to burn and release heat energy. There are three main types of fuels - solid, liquid, and gaseous. Solid fuels include coal and wood. Liquid fuels include kerosene, diesel, and furnace oil. Common gaseous fuels used in India are LPG, natural gas, and coal gas. The amount of heat released when fuels combust is measured by their calorific value, with gaseous fuels having the highest calorific value per unit weight. Proper use and safety precautions are required when using fuels to prevent fires and other hazards.
This document provides information about fuels and combustion. It discusses different types of fuels such as primary/natural fuels (wood, coal, dung) and secondary/derived fuels (coke, charcoal, tar). It defines combustion as the oxidation of fuels and explains how it liberates heat energy. Gross calorific value and net calorific value are defined. Bomb calorimeter is described as a method to determine calorific values. Corrections made during bomb calorimeter experiments are also outlined. Cathodic protection techniques for corrosion control are summarized. Finally, different water softening methods like zeolite process, ion exchange, and reverse osmosis are briefly introduced.
The ppt is especially designed for engineering students. The lecture explains about fuels, its types, characteristics and in the last we have discussed about measurement of calorific value using Bomb calorimeter.
This document discusses fuels and their analysis. It begins by defining fuels and providing examples of primary and secondary fuels. It then discusses the characteristics of a good fuel and explains calorific value. It describes how to determine calorific value using a bomb calorimeter and provides the calculation. The document also explains proximate analysis and ultimate analysis of coal, including how each analysis is performed and its significance. In summary, it provides an overview of different fuel types, characteristics of good fuels, methods of determining calorific value, and approaches to analyzing coal composition.
Combustion is a chemical process in which a substance reacts rapidly with oxygen and gives off heat. The original substance is called the fuel, and the source of oxygen is called the oxidizer. The fuel can be a solid, liquid, or gas, although for airplane propulsion the fuel is usually a liquid. The oxidizer, likewise, could be a solid, liquid, or gas.
1. Fuels are combustible substances containing mainly carbon that produce heat energy when burned. Coal, petroleum, and natural gas are important primary fossil fuels found naturally.
2. Fuels can be classified based on their physical state as solid, liquid, or gaseous. They can also be classified as primary fuels found in nature or secondary fuels derived from primary fuels.
3. The calorific value of a fuel is the amount of heat released during complete combustion. It is usually measured in kilocalories per kilogram. Higher calorific value includes the heat of condensation of water vapor produced, while lower calorific value does not.
1. A fuel is a combustible substance containing carbon as the main constituent that produces heat energy when burned. During combustion, carbon and hydrogen in the fuel combine with oxygen to produce heat.
2. Fuels are classified as primary fuels, which occur naturally like coal, petroleum and natural gas, or secondary fuels, which are derived from primary fuels like coke and gasoline. Fuels can also be classified as solid, liquid or gaseous based on physical state.
3. The calorific value of a fuel is the total quantity of heat produced during complete combustion of a unit mass or volume of fuel. Higher or gross calorific value includes the latent heat of condensation of water vapor produced,
1. Fuels are combustible substances containing mainly carbon that produce heat energy when burned. Coal, petroleum, and natural gas are important primary fossil fuels found naturally.
2. Fuels can be classified based on their physical state as solid, liquid, or gaseous. They can also be classified as primary fuels found in nature or secondary fuels derived from primary fuels.
3. The calorific value of a fuel is the amount of heat released during complete combustion. It is usually measured in kilocalories per kilogram. Higher calorific value includes the heat of condensation of water vapor produced, while lower calorific value does not.
Calorific value refers to the total heat released when a fuel is completely burned. There are two types of calorific values for fuels containing hydrogen: higher (gross) calorific value and lower (net) calorific value. The higher calorific value includes the latent heat released from condensation of water vapor in the combustion products, while the lower calorific value does not include this latent heat as it escapes with the gases. The lower calorific value can be calculated by subtracting the latent heat of vaporization of hydrogen from the gross calorific value. Dulong's formula can also be used to theoretically calculate the calorific value based on the fuel's carbon, hydrogen, oxygen,
This PowerPoint presentation covers the topic of fuel and its characteristics. It defines fuel as combustible substances that produce large amounts of heat when burned. Fuels are classified as primary/natural or secondary/artificial, and by physical state as solid, liquid or gas. Characteristics of good fuels include high calorific value, moderate ignition temperature, low moisture and non-combustible content, and producing minimal smoke and non-poisonous gases. Calorific value is calculated using the Dulong formula and depends on the fuel's carbon, hydrogen, oxygen and sulfur content. Multiple choice questions review the key concepts.
This document provides information about fuels and lubricants. It discusses different types of fuels like coal, natural gas, and plastic waste. It also covers the classification of fuels based on rank like peat, lignite, bituminous coal, and anthracite. The characteristics of good fuels and various units of heat measurement like calorie, kilocalorie, and British Thermal Unit are explained. The document discusses the gross calorific value and net calorific value of fuels. It provides details about the working of a bomb calorimeter and the proximate and ultimate analysis of coal.
The document discusses different types of fuels and fuel cells. It begins by defining fuels as combustible substances that produce a large amount of heat during combustion. Fuels are classified based on their occurrence as primary or natural fuels, and secondary or artificial fuels. They are also classified based on their physical state as solid, liquid, or gas. The document then discusses characteristics of good fuels, methods of determining calorific value such as bomb calorimetry and Boy's calorimetry, and concludes with a summary of fuel cells - their components and basic working principle of converting chemical energy directly to electrical energy.
The document discusses various types of fuels, their classification, properties, and uses. It describes solid fuels like wood, peat, lignite, and coal as well as liquid fuels derived from petroleum. The key solid fuel discussed is coal, which is classified based on carbon content and rank into peat, lignite, sub-bituminous coal, bituminous coal, semi-bituminous coal, and anthracite. Liquid fuels are obtained through refining of crude petroleum and include fuels like gasoline, kerosene and diesel.
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
This document discusses the fundamentals of fuels, including their classification, calorific value, and analysis. It begins by defining what a fuel is and providing examples. It then covers:
- Classification of fuels into primary/natural and secondary/derived types.
- Calorific value and different units used to measure heat such as calories, kilocalories, BTUs. It defines gross/higher and lower/net calorific values.
- Methods of determining calorific value using a bomb calorimeter, involving burning a fuel sample and calculating the heat released based on temperature changes.
- Proximate analysis of coal to determine moisture, volatile matter, ash, and fixed carbon content.
Petroleum is a mixture of hydrocarbons that can be separated into fractions by fractional distillation based on differences in boiling points. The top five crude oil producing countries are Saudi Arabia, Russia, the United States, Iran, and China. Petroleum is heated to 360°C in the absence of air during oil refining to vaporize it before fractional distillation, in order to prevent ignition and potential explosions.
Fuel is a combustible substance, containing carbon as main constituent, which...drmanojkarar
Energy resources: While selecting an ideal fuel for domestic or industrial purpose we should keep in mind that the fuel selected must possess the following characteristic properties.
1) It should possess high calorific value.
2) It should have proper ignition temperature. The ignition temperature of the fuel should neither be too low nor too high.
3) It should not produce poisonous products during combustion. In other words, it should not cause pollution o combustion.
4) It should have moderate rate of combustion.
5) Combustion should be easily controllable i.e., combustion of fuel should be easy to start or stop as and when required.
6) It should not leave behind much ash on combustion.
7) It should be easily available in plenty.
8) It should have low moisture content.
9) It should be cheap.
10) It should be easy to handle and transport.
Calorific value: It is defined as the total amount of heat liberated, when unit mass or unit volume of the fuel is completely burnt in air or oxygen.
Units of heat:
a) Calorie: The amount of heat required to increase the temperature of 1 gm of water through one degree centigrade.
b) Kilocalorie: It is equal to 1000 calories. The quantity of heat required to rise the temperature of 1 Kg of water through one degree centigrade.
1 K.cal = 1000 cals
c) British thermal unit (B.Th.U.): The quantity of heat required to rise the temperature of 1 pound of water through one degree Farenheit.
1 B.Th.U = 252 cals = 0.252 K.cal
d) Centigrade heat unit (C.H.U): The quantity of heat required to rise the temperature of one pound of water through one degree centigrade.
1 K. cal = 3.968 B.Th.U = 2.2 C.H.U
For solids or liquid fuel: Calorie/gm (cal/gm) (or) Kilocalorie/Kg (K.cal/Kg) (or) B.Th.U/lb
For gaseous fuels: Kilocalorie/cubic meter (K.cal/m3) (or) B.Th.U/ft3
the slides explain about fuel and combustionrndfme
The document discusses different types of fuels and combustion. It provides classifications of fuels as primary, secondary, solid, liquid, and gaseous. It defines calorific value and explains gross calorific value and net calorific value. The document discusses solid fuels like coal, its classification and analysis including proximate analysis and ultimate analysis. It explains the importance of these analyses. It also discusses the production of metallurgical coke and its required properties.
Fuels are substances that readily combine with oxygen to burn and release heat energy. There are three main types of fuels - solid, liquid, and gaseous. Solid fuels include coal and wood. Liquid fuels include kerosene, diesel, and furnace oil. Common gaseous fuels used in India are LPG, natural gas, and coal gas. The amount of heat released when fuels combust is measured by their calorific value, with gaseous fuels having the highest calorific value per unit weight. Proper use and safety precautions are required when using fuels to prevent fires and other hazards.
This document provides information about fuels and combustion. It discusses different types of fuels such as primary/natural fuels (wood, coal, dung) and secondary/derived fuels (coke, charcoal, tar). It defines combustion as the oxidation of fuels and explains how it liberates heat energy. Gross calorific value and net calorific value are defined. Bomb calorimeter is described as a method to determine calorific values. Corrections made during bomb calorimeter experiments are also outlined. Cathodic protection techniques for corrosion control are summarized. Finally, different water softening methods like zeolite process, ion exchange, and reverse osmosis are briefly introduced.
The ppt is especially designed for engineering students. The lecture explains about fuels, its types, characteristics and in the last we have discussed about measurement of calorific value using Bomb calorimeter.
This document discusses fuels and their analysis. It begins by defining fuels and providing examples of primary and secondary fuels. It then discusses the characteristics of a good fuel and explains calorific value. It describes how to determine calorific value using a bomb calorimeter and provides the calculation. The document also explains proximate analysis and ultimate analysis of coal, including how each analysis is performed and its significance. In summary, it provides an overview of different fuel types, characteristics of good fuels, methods of determining calorific value, and approaches to analyzing coal composition.
Combustion is a chemical process in which a substance reacts rapidly with oxygen and gives off heat. The original substance is called the fuel, and the source of oxygen is called the oxidizer. The fuel can be a solid, liquid, or gas, although for airplane propulsion the fuel is usually a liquid. The oxidizer, likewise, could be a solid, liquid, or gas.
1. Fuels are combustible substances containing mainly carbon that produce heat energy when burned. Coal, petroleum, and natural gas are important primary fossil fuels found naturally.
2. Fuels can be classified based on their physical state as solid, liquid, or gaseous. They can also be classified as primary fuels found in nature or secondary fuels derived from primary fuels.
3. The calorific value of a fuel is the amount of heat released during complete combustion. It is usually measured in kilocalories per kilogram. Higher calorific value includes the heat of condensation of water vapor produced, while lower calorific value does not.
1. A fuel is a combustible substance containing carbon as the main constituent that produces heat energy when burned. During combustion, carbon and hydrogen in the fuel combine with oxygen to produce heat.
2. Fuels are classified as primary fuels, which occur naturally like coal, petroleum and natural gas, or secondary fuels, which are derived from primary fuels like coke and gasoline. Fuels can also be classified as solid, liquid or gaseous based on physical state.
3. The calorific value of a fuel is the total quantity of heat produced during complete combustion of a unit mass or volume of fuel. Higher or gross calorific value includes the latent heat of condensation of water vapor produced,
1. Fuels are combustible substances containing mainly carbon that produce heat energy when burned. Coal, petroleum, and natural gas are important primary fossil fuels found naturally.
2. Fuels can be classified based on their physical state as solid, liquid, or gaseous. They can also be classified as primary fuels found in nature or secondary fuels derived from primary fuels.
3. The calorific value of a fuel is the amount of heat released during complete combustion. It is usually measured in kilocalories per kilogram. Higher calorific value includes the heat of condensation of water vapor produced, while lower calorific value does not.
Calorific value refers to the total heat released when a fuel is completely burned. There are two types of calorific values for fuels containing hydrogen: higher (gross) calorific value and lower (net) calorific value. The higher calorific value includes the latent heat released from condensation of water vapor in the combustion products, while the lower calorific value does not include this latent heat as it escapes with the gases. The lower calorific value can be calculated by subtracting the latent heat of vaporization of hydrogen from the gross calorific value. Dulong's formula can also be used to theoretically calculate the calorific value based on the fuel's carbon, hydrogen, oxygen,
This PowerPoint presentation covers the topic of fuel and its characteristics. It defines fuel as combustible substances that produce large amounts of heat when burned. Fuels are classified as primary/natural or secondary/artificial, and by physical state as solid, liquid or gas. Characteristics of good fuels include high calorific value, moderate ignition temperature, low moisture and non-combustible content, and producing minimal smoke and non-poisonous gases. Calorific value is calculated using the Dulong formula and depends on the fuel's carbon, hydrogen, oxygen and sulfur content. Multiple choice questions review the key concepts.
This document provides information about fuels and lubricants. It discusses different types of fuels like coal, natural gas, and plastic waste. It also covers the classification of fuels based on rank like peat, lignite, bituminous coal, and anthracite. The characteristics of good fuels and various units of heat measurement like calorie, kilocalorie, and British Thermal Unit are explained. The document discusses the gross calorific value and net calorific value of fuels. It provides details about the working of a bomb calorimeter and the proximate and ultimate analysis of coal.
The document discusses different types of fuels and fuel cells. It begins by defining fuels as combustible substances that produce a large amount of heat during combustion. Fuels are classified based on their occurrence as primary or natural fuels, and secondary or artificial fuels. They are also classified based on their physical state as solid, liquid, or gas. The document then discusses characteristics of good fuels, methods of determining calorific value such as bomb calorimetry and Boy's calorimetry, and concludes with a summary of fuel cells - their components and basic working principle of converting chemical energy directly to electrical energy.
The document discusses various types of fuels, their classification, properties, and uses. It describes solid fuels like wood, peat, lignite, and coal as well as liquid fuels derived from petroleum. The key solid fuel discussed is coal, which is classified based on carbon content and rank into peat, lignite, sub-bituminous coal, bituminous coal, semi-bituminous coal, and anthracite. Liquid fuels are obtained through refining of crude petroleum and include fuels like gasoline, kerosene and diesel.
Similar to fuel and combustion slides 2022.pptx (20)
A review on techniques and modelling methodologies used for checking electrom...nooriasukmaningtyas
The proper function of the integrated circuit (IC) in an inhibiting electromagnetic environment has always been a serious concern throughout the decades of revolution in the world of electronics, from disjunct devices to today’s integrated circuit technology, where billions of transistors are combined on a single chip. The automotive industry and smart vehicles in particular, are confronting design issues such as being prone to electromagnetic interference (EMI). Electronic control devices calculate incorrect outputs because of EMI and sensors give misleading values which can prove fatal in case of automotives. In this paper, the authors have non exhaustively tried to review research work concerned with the investigation of EMI in ICs and prediction of this EMI using various modelling methodologies and measurement setups.
Harnessing WebAssembly for Real-time Stateless Streaming PipelinesChristina Lin
Traditionally, dealing with real-time data pipelines has involved significant overhead, even for straightforward tasks like data transformation or masking. However, in this talk, we’ll venture into the dynamic realm of WebAssembly (WASM) and discover how it can revolutionize the creation of stateless streaming pipelines within a Kafka (Redpanda) broker. These pipelines are adept at managing low-latency, high-data-volume scenarios.
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
Redefining brain tumor segmentation: a cutting-edge convolutional neural netw...IJECEIAES
Medical image analysis has witnessed significant advancements with deep learning techniques. In the domain of brain tumor segmentation, the ability to
precisely delineate tumor boundaries from magnetic resonance imaging (MRI)
scans holds profound implications for diagnosis. This study presents an ensemble convolutional neural network (CNN) with transfer learning, integrating
the state-of-the-art Deeplabv3+ architecture with the ResNet18 backbone. The
model is rigorously trained and evaluated, exhibiting remarkable performance
metrics, including an impressive global accuracy of 99.286%, a high-class accuracy of 82.191%, a mean intersection over union (IoU) of 79.900%, a weighted
IoU of 98.620%, and a Boundary F1 (BF) score of 83.303%. Notably, a detailed comparative analysis with existing methods showcases the superiority of
our proposed model. These findings underscore the model’s competence in precise brain tumor localization, underscoring its potential to revolutionize medical
image analysis and enhance healthcare outcomes. This research paves the way
for future exploration and optimization of advanced CNN models in medical
imaging, emphasizing addressing false positives and resource efficiency.
Comparative analysis between traditional aquaponics and reconstructed aquapon...bijceesjournal
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
International Conference on NLP, Artificial Intelligence, Machine Learning an...gerogepatton
International Conference on NLP, Artificial Intelligence, Machine Learning and Applications (NLAIM 2024) offers a premier global platform for exchanging insights and findings in the theory, methodology, and applications of NLP, Artificial Intelligence, Machine Learning, and their applications. The conference seeks substantial contributions across all key domains of NLP, Artificial Intelligence, Machine Learning, and their practical applications, aiming to foster both theoretical advancements and real-world implementations. With a focus on facilitating collaboration between researchers and practitioners from academia and industry, the conference serves as a nexus for sharing the latest developments in the field.
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
2. Introduction: Fuels
Fuels are combustible substance containing carbon as the main constituent
On proper burning gives large amount of heat that can be used economically for domestic and industrial
purposes
During the process of combustion of a fuel, the atoms of carbon, hydrogen, etc combine with oxygen
with simultaneous liberation of heat
C + O2 CO2 + 94 kcals
2H2 + O2 2H2O + 68.5 kcals
Main source of fuel is coal and petroleum. These are stored fuels available in earth's crust and are
generally called fossil fuels because they were formed from the fossilized remains of plants and animals
2
3. What are the characteristics of a good fuel?
1. High calorific value
2. Moderate ignition temperature
3. Low moisture content
4. Low non-combustible matter content
5. Moderate velocity of combustion
6. Products of combustion should not be harmful
7. Low cost
8. Easy to transport
9. Easy control of combustion
10.Should not undergo spontaneous combustion
11.Storage cost in bulk should be low
12.Burn efficiently without smoke
13.Uniform size in solid fuel for regular combustion.
4. Transportation of Fuel: (Big issues)
Cars (growing rapidly in Asia)
Trucks (Critical for economy everywhere)
Air Planes (Growing rapidly everywhere)
Liquid Fuels:
Liquids Flow (Solids are hard to handle)
High volumetric and mas-energy density.
Easy to store and distribute
5. Classification
5
STATE
OF
AGGREGATION
LIQUID GASEOUS
LIQUID GASEOUS
• Crude Oil • Natural gas
SOLID
SOLID
• Coke
• Charcoal
• Petroleum
• Briquette
• Tar
• Kerosene
• Diesel
• Petrol
• Fuel oil
• Synthetic gasoline
• LPG
• Coal gas
• Water gas
• Bio gas
• Wood
• Peat
• Lignite
• Coal
• Dung
CHEMICAL FUELS
SECONDARY OR DERIVED
PRIMARY OR NATURAL
6. HCV and LCV
Higher or gross calorific value (HCV):
• Usually, all fuels contain some hydrogen and when the calorific value of hydrogen-containing fuel is
determined experimentally, the hydrogen is converted into steam. If the products of combustion are
condensed to the room temperature (25°C), the latent heat of condensation of steam also gets included in
the measured heat, which is then called "higher or gross calorific value". So, gross or higher calorific value
(HCV) is "the total amount of heat produced, when unit mass/volume of the fuel has been burnt
completely and the products of combustion have been cooled to room temperature"(i.e., 25°C).
Lower or net calorific value (LCV):
• In actual use of any fuel, the water vapour and moisture, etc., are not condensed and escape as such along-
with hot combustion gases. Hence, a lesser amount of heat is available. So, net or lower calorific value
(LCV) is "the net heat produced, when unit mass /volume of the fuel is burnt completely and the products
are permitted to escape".
• Net calorific value = HCV - Latent heat of water vapours formed
= HCV - Mass of hydrogen x a x Latent heat of steam
Since 1 part by mass of hydrogen produces ‘a’ part by mass of water.
6
7. Units of Calorific Value
CALORIFIC VALUE
Calorific value of a fuel is "the total quantity of heat liberated, when a unit mass (or volume) of the fuel is burnt
completely."
Units of heat :
(1) 'Calorie' is the amount of heat required to raise the temperature of one gram of water through one degree Centigrade
(15-16°C).
(2) "Kilocalorie" is equal to 1,000 calories. It may be defined as 'the quantity of heat required to raise the temperature of
one kilogram of water through one degree Centigrade. Thus: 1 kcal = 1,000 cal
(3) "British Thermal unit" (B.T.U.) is defined as "the quantity of heat required to raise the temperature of one pound of
water through one degree Fahrenheit (60-61°F). This is the English system unit.
1 B.T.U. = 252 cal = 0.252 kcal 1 kcal = 3.968 B.T.U.
7
8. Determination of Calorific Value
1. BOMB CALORIMETER
The apparatus which is used to determine the calorific value of solid and liquid fuels is known as Bomb Calorimeter.
Fig. 1: Bomb Calorimeter
8
9. Bomb Calorimeter
Calorific value determination
• A weighed mass of fuels placed in the crucible is allowed to burn in oxygen by electric spark across the electrode
• Heat liberated is measured by principle of calorimetry i.e. taken by water and calorimeter
• Initial and final temperatures of calorimeter are noted
Calculation
m = mass of fuel pellet
W = mass of water in the calorimeter
w = water equivalent of calorimeter
t1 = initial temperature of calorimeter
t2 = final temperature of calorimeter
HCV = gross calorific value of calorimeter
L= 𝐻𝐶𝑉 =
𝑊+𝑤 (𝑡2
−𝑡1
)
𝑚
𝑐𝑎𝑙/𝑔𝑚
Fuel used = benzoic acid (GCV = 6325 kcal/kg)
9
10. Correction
Correction factors are used to get accurate results which include:
A. Fuse Wire Correction:
Heat liberated during sparking should be subtracted from heat liberated.
B. Acid Correction:
Fuels containing sulphur and nitrogen if oxidized, the heat of formation of H2SO4 and HNO3 should be subtracted (as the
acid formations are exothermic reactions).
C. Cooling Correction:
Rate of cooling of temperature from max. temperature to room temperature is noted. From the rate of cooling and the
actual time taken for cooling then correction is called cooling correction and is added to the (t2-t1) term.
𝐿 =
𝑊 + 𝑤 𝑡2 − 𝑡1 + 𝑐𝑜𝑜𝑙𝑖𝑛𝑔 𝑐𝑜𝑟𝑟𝑒𝑐𝑡𝑖𝑜𝑛 − (𝐴𝑐𝑖𝑑 + 𝐹𝑢𝑠𝑒 𝑐𝑜𝑟𝑟𝑒𝑐𝑡𝑖𝑜𝑛)
𝑚
𝑐𝑎𝑙/𝑔𝑚
10
11. Theoretical calculation of Calorific Value
2. Dulong’s Formula
is used for the calculation of calorific value from the chemical composition of fuel.
i.e. HCV = sum of HCV’s of individual elemental constituents present in the fuel
• Derivation:
Exothermic reactions during the process of combustion with their respective HCV values are:
C + O2 CO2 + 8080 kcal/kg
H2+1/2O2 H2O + 34500 kcal/kg
S+O2 SO2 + 2240 kcal/kg
Oxygen present in the fuel is assumed to be present as water and which also prevents some part of hydrogen
available for combustion
H2+ 1/2O2 H2O + 34500 kcal/kg
2g 16g 18g
1 8 9
11
12. Dulong's formula
So, Available hydrogen for combustion = Total hydrogen – Fixed hydrogen in the form of H2O
= Total hydrogen – 1/8 (mass of oxygen in fuel)
So if C, H, O and S percentages of carbon, hydrogen, oxygen and sulphur, respectively are known then,
⇒ 𝐻𝐶𝑉 = [8080 ×
𝐶
100
+
34500
100
𝐻 −
𝑂
8
+ 2240 ×
𝑆
100
] 𝑘𝑐𝑎𝑙/𝑘𝑔
or, 𝐇𝐂𝐕 =
𝟏
𝟏𝟎𝟎
[𝟖𝟎𝟖𝟎𝐂 + 𝟑𝟒𝟓𝟎𝟎 𝐇 −
𝐎
𝟖
+ 𝟐𝟐𝟒𝟎𝐒 ] 𝐤𝐜𝐚𝐥/𝐤𝐠
and, 𝐋𝐂𝐕 = 𝐇𝐂𝐕 − 𝟎. 𝟎𝟗𝐇 × 𝟓𝟖𝟕 𝐤𝐜𝐚𝐥/𝐤𝐠
as 1 part of H by mass gives 9 parts of H2O, and latent heat of steam is 587 kcal/kg
12
13. Exercise
Que: Calculate the gross and net calorific value of coal having the following composition
C 85 %
H 8 %
S 1 %
N 2 %
ash 4 %
Latent heat of steam = 587 cal/g
13
14. Determination of Calorific Value
3. BOY’S GAS CALORIMETER
Used for measuring the calorific value of
gaseous and liquid fuels
A known volume of gas is burnt at a uniform rate
Around the burner there is a chimney containing
coils wherein water is passed with a constant rate
Separate thermometer are used to measure the
incoming and outgoing water temperatures (t1
and t2)
Fig. 2: Boy’s Gas Calorimeter
14
15. Boy’s Gas Calorimeter
CALCULATION
Let V = volume of gas burning
W = mass of cooling water used in time t
t1 and t2 = incoming and outgoing water temperatures respectively
m = mass of steam condensed in time t
Total heat liberated = V x HCV
Total heat absorbed = W x (t2 - t1)
So, we get 𝐇𝐂𝐕 =
𝐖 ×(𝐭𝟐
−𝐭𝟏)
𝐕
Also mass of water condensed per m3 of gas = m/V kg
So latent heat of steam per m3 of gas =
𝑚 ×587
𝑉
kcal
So, 𝐍𝐂𝐕 = 𝐇𝐂𝐕 −
𝐦 ×𝟓𝟖𝟕
𝐕
𝐤𝐜𝐚𝐥/𝐦𝟑
15
16. Liquid Fuels
16
The important liquid fuels are petroleum, petroleum products, tar, alcohols.
These are naturally found under the sea surface.
Liquid fuels are also obtained synthetically from' hydrogenation of coat. Liquid fuels find extensive
use in domestic and industrial fields.
The important liquid fuels are petroleum, petroleum products, tar, alcohols. These are naturally
found under the sea surface. Liquid fuels are also obtained synthetically from' hydrogenation of
coat. Liquid fuels find extensive use in domestic and industrial fields.
Petroleum (petra = rock; oleum = oil)
Petroleum or crude oil is a dark greenish brown or black colored viscous oil found deep in earth's
crust.
The oil is usually floating over a brine solution and above the oil, natural gas is present. Crude oil
containing mixture of paraffinic, olefinic and aromatic hydrocarbons with minor amounts of organic
compounds like N, 0 and S.
The average composition of crude oil is C =80 - 87 %, H =11-15%, S = 0.1 -3.5%, (N +O) =0.1-
0.5%.
17. Petroleum
17
Classification of petroleum
Petroleum is classified into three types based on variation of chemical nature of crude oil found in the
earth.
• Paraffinic-base type crude oil: It contains saturated hydrocarbons from CH4 to C35H72 and little
amount of naphthalenes and aromatics.
• Asphaltic-base type crude oil: It contains mainly cycloparaffins or naphthalenes with smaller
amount of paraffins and aromatic hydrocarbons. Hydrocarbons from C18H38 to C35H72 are called
waxes.
• Mixed-base type crude oil : It contains both paraffinic and asphaltic hydrocarbons and are
generally in the form of semi-solid waxes.
(Naphthalene) (Methyl naphthalene)
18. Petroleum
18
Origin of petroleum
Resulted from the partial decomposition of marine animals and vegetable organisms of pre-historic
forests
These materials had buried by changes in earth (like earthquake, volcano etc.) and subjected to high
pressure and temperature during the ages of time
Then influenced by either radioactive elements or bacterial decomposition under anaerobic
conditions to get converted to various hydrocarbons
19. Mining of Petroleum
19
Done by drilling holes in the earth crust and sinking pipes upto the oil-bearing porous rocks
Oil usually gushes out itself due to hydrostatic pressure of natural gas.
Then it may be mechanically pumped up by using either lift pump or air-lift pump.
Mining of crude oil and use of air-lift pump
20. Refining of Petroleum
20
The crude oil obtained from the earth crust contains water, sulphur and some unwanted impurities.
After removal of water, sulphur and these impurities, the crude oil is separated into various useful fractions by fractional
distillation and finally converted into desired specific products having different boiling points. The process is called
"Refining of Petroleum" and the refining plants are called "Oil refineries". The process of refining involves the following
steps.
Step -I: Separation of water (Cottrell's process)
The crude oil from the oil well is an extremely stable emulsion of oil and salt water. The crude oil is allowed to flow
between two highly charged electrodes, where colloidal water droplets coalesce to form large drops, which is then separated
out from the oil.
Step - II: Removal of harmful impurities
(a) The presence of NaCI and MgCI in the crude oil can corrode the refining equipment, hence these salts are removed by
electrical desalting and dehydration methods.
(b) The sulphur compounds present in the crude oil is removed by treating oil with copper oxide, which results in the
formation of copper sulphide (solid), which is then removed by filtration.
21. Fractional distillation
21
Step - III: Fractional distillation
The crude oil is then heated to about 400°C in an iron retort,
whereby all volatile substances (except asphalt or coke) are
evaporated. The hot vapors are then passed up a fractionating
column, which is a tall cylindrical tower containing a number
of horizontal stainless steel trays at short distances. Each tray
is provided with small chimney covered with a loose cap.
When the vapours of the oil go up in the fractionating
column, they become gradually cooler and get condensed at
different heights of column. The fractions having higher
boiling points condense at lower trays whereas the fractions
having lower boiling points condense at higher trays. The
gasoline obtained by the fractional distillation is called
straight --run gasoline. Various fractions obtained at different
trays are given in table.
22. Fractional distillation
22
Sn. Name of the fractions
Boiling
range (OC)
Composition
of Hydrocarbons
.
Uses
1. Uncondensed gases Below 30°C C1 to C4
As domestic and
industrial fuel under
the name LPG
2. Petroleum ether 30 70 °C C5 to C7
As a solvent.
3.
Gasoline (or) petrol. 40 - 120 °C
C5 to C9
As motor fuel, solvent and in
dry cleaning.
4.
Naphtha ( or}solvent spirit
.
120. - 180 °C C9 to C10
As solvent and in dry
cleaning.
5. Kerosene oil. 180 - 250 °C C10 to CI6
As fuel for jet engines
and an illuminant.
6. Diesel oil (or) gas oil 250 320 °C C10 to CI8
As Diesel engine fuel.
7. Heavy oil. 320 - 400 °C C17 to C30
Production of gasoline by
cracking
process.
23. Fractional distillation of Heavy Oil
23
Sn. Name of the fractions
Boiling
range (OC)
Composition
of Hydrocarbons
.
Uses
1. Lubricating oil - C17 to C20
Used as lubricants
2. Petroleum jelly (Vaseline) - -
Used in medicines and cosmetics
3.
Paraffin wax -
C20 to C28
Used in candles, wax paper, boot
polish, etc
4. Grease - - Used as lubricants.
5. Asphalt or bitumen Above 400°C C30 and above
Used for making roads, water
proof roofing, etc
24. Cracking
24
Cracking
The decomposition of bigger hydrocarbon molecules into simpler, low boiling hydrocarbons of lower molecular
weight is called Cracking.
The gasoline obtained from the fractional distillation of petroleum, has the highest demand as a motor fuel, but the
yield of this fractions is only 20-30% (Crude oil) and also quality as straight-run gasoline which is not good and
hence is used only after proper blending. To overcome these difficulties, the higher boiling fractions (e.g. fuel oil
and gas oil) are converted into lower boiling fractions gasoline (petrol) by cracking process.
The cracked gasoline gives better engine performance i.e., they are suitable for spark-ignition engines of
automobiles. In cracking process, higher saturated hydrocarbon molecules are converted into simpler molecules
such as paraffinic and olefinic hydrocarbons.
Cracking
C10H22 C5H12 + C5H10
Decane n-pentane pentene
B.P. = 174 °C B.P. = 36 °C
25. Types of Cracking: Thermal Cracking
25
There are two methods of cracking in use
1. Thermal cracking 2. Catalytic cracking
Thermal cracking
In this process, the heavy oil is subjected to high temperature and pressure, when the bigger hydrocarbon molecules
break down to give smaller molecules of the paraffins, olefins and hydrogen.
The cracked products are then separated by fractional distillation.
This process is carried out in liquid phase at a temperature of 475 - 530° C and under pressure of 100 kg/cm2 is called
Liquid-phase thermal cracking
or at a temperature of 600-650°C (heavy oil is vapourised) and under a low pressure of 10-20 kg/cm2, such process is
called Vapour-phase thermal cracking.
Petrol obtained from vapor phase cracking has better anti-knock properties but poor stability than petrol from liquid
phase cracking.
26. Catalytic Cracking
26
Catalytic Cracking
In this process, cracking is carried out in presence of a catalyst at lower temperature (300° C to 450° C) and pressures (l
to 5 kg/cm2). The catalyst like aluminum silicate [Al2(SiO3)] or alumina [A12O3] used in cracking gives higher yield and
better quality of gasoline. There are two types of catalytic cracking in use
Advantages
i. No external fuel is required. Heat required is derived from coal, embedded in the catalyst.
ii. Low pressure is required (1-5 kg/cm2)
iii. Product contain very less amount of Sulphur (major part escapes out as H2S gas)
iv. Catalytic cracking yields a higher quantity of branched-chain, unsaturated, aromatic hydrocarbons as compared to
thermal cracking and hence have better anti-knock characteristics
There are two types of catalytic cracking in use
i) Fixed-bed catalytic cracking
ii) Fluid (Moving)-bed catalytic cracking
27. Fixed-bed catalytic cracking
27
The heavy oil is passed through the heater, where the oil is vapourised and heated to 400 to 500°C and then forced through
a catalytic champers containing the catalyst of silica alumina gel (SiO2, Al2O3) or bauxite, is mixed with clay and
zirconium oxide maintained at 400 to 500°C and 1.5 kg/cm2 pressure. During their passage through the tower, cracking
takes place about 30-40% of the charge is converted into gasoline and about 2- 4% carbon is formed which gets deposited
on the catalytic bed.
The vapours produced are then passed through a fractionating column, where heavy oil fractions condensed. The vapours
are then admitted into a cooler, where some of the gaseous products are condensed along with gasoline and uncondensed
gases move on. The gasoline containing some dissolved gases is then sent to a stabilizer, where the dissolved gases are
removed and pure gasoline is obtained.
When substantial amount of carbon is deposited on the catalyst bed, during cracking, the catalyst stops functioning. It is
reactivated by burning off the deposited carbon in a stream of hot air. During the reactivation of catalyst, the vapours are
diverted through another catalyst chamber.
29. Fluid (Moving)-bed catalytic cracking
29
In this process, solid catalyst is finely powdered, so that it behaves almost as a fluid, which can be circulated in gas
stream.
The vapours of cracking stock (gas oil, heavy oil, etc.,) mixed with fluidized catalyst is forced up into a large reactor
bed in which cracking of the heavier molecules into lighter molecules occurs at a temperature of 530°C and pressure
of about 3 to 5 kg/cm2.
The top of the reactor, there is a centrifugal separator, which, allows the low boiling lighter molecules move up to the
top of the reactor and enter into the fractionating column but retains all the catalyst powder in the reactor itself.
The carbon deposited on the catalyst powder are burnt off in the regenerator and the temperature rises to about 590°C
or more.
The cracked gases and gasoline are removed from the top of the fractionating column and sent to a cooler, where
gasoline is condensed. It is then sent to a stabilizer to recover pure gasoline.
The product contains a higher proportion of aromatics and iso-paraffins.
32. Polymerization
32
Gases obtained as a by-product from cracking of heavy oils, etc., contains olefins (like ethylene, propene
and butenes) and alkanes (such as methane, ethane, propane and butane).
This gaseous mixture when subjected to high pressure and high temperature with or without catalyst, it
polymerize to form bigger hydrocarbons called polymer gasoline.
Types of polymerization
Thermal Polymerization: at temperature 500-600°C and 70-350 kg/cm2. Product is gasoline and gas oil
mixture
Catalytic Polymerization: at 150-200°C and in presence of catalyst like phosphoric acid. Products are
gasoline and unpolymerized gas which is separated and recycled for polymerization
33. Fishcher-Tropsch method
33
In this process, coal is first converted into coke. Then water gas (CO + H2) is produced by the action of steam over
red hot coke.
The gas is purified by passing through Fe2O3 (to remove H2S) and then into a mixture of Fe2O3.Na2CO3 (to remove
organic Sulphur compounds).
The purified gas is compressed to 5 to 25 atm and then led through a converter (containing a catalyst, consisting of a
mixture of 100 parts cobalt, 5 parts thoria, 8 parts magnesia and 200 parts kieselguhr earth) maintained at ~200-
300°C.
Reaction is exothermic, so outcoming hot mixture is led to a cooler, where a liquid is resembling crude oil is
obtained
Crude oil then fractionated to get gasoline and high boiling point heavy oil
Heavy oil then recycled for cracking to get more gasoline.
35. Bergius Process
35
This method was developed by Bergius in Germany during the First World War.
The low ash coal is finely powdered and made into a paste with heavy oil and then a catalyst (composed of tin or nickel
oleate) is incorporated.
The whole is heated with hydrogen at 450°C and under a pressure 200-250 atm for about 1.5 hours, during which
hydrogen combines with coal to form saturated hydrocarbons, which decompose at prevailing high temperature and
pressure to yield low-boiling liquid hydrocarbons.
The issuing gases (from the reaction vessel) are led to condenser, where a liquid resembling crude oil is obtained, which
is then fractionated to get: (i) gasoline, (ii) middle oil, and (iii) heavy oil.
The latter is used again for making paste with fresh coal dust. The middle oil is hydrogenated in vapour-phase in
presence of a solid catalyst to yields more gasoline. The yields of gasoline in about 60% of the coal dust used.
37. Refining of Gasoline
37
Gasoline obtained from fractionation of crude petroleum contains some undesirable unsaturated straight chain
hydrocarbons and Sulphur compounds
These hydrocarbons gets oxidized and polymerized to form gum and sludge on storing
Also Sulphur compounds lead to corrosion of internal combustion engine
Characteristics of an ideal gasoline
1. It must be cheap and readily available
2. It must burn clean and produce no corrosion , etc., on combustion
3. It should mix readily with air and afford uniform manifold distribution, i.e., it should easily vaporize
4. It must be knock resistant
5. It should not pre-ignite easily
6. It should not tend to decrease the volumetric efficiency of the engine
7. It must have high calorific value
38. Refining
38
The sulphur compounds are, generally, removed by treating gasoline with an alkaline solution of sodium plumbite
with controlled addition of S. This refining process (called 'sweetening') converts sulphur compounds into
disulphides (Doctor's process).
PbS is removed by filtration
Disulphides are extracted with a suitable solvents
After the refining of gasoline, some inhibitors are added. These retard the oxidation reactions, thereby improving
storing qualities of gasoline.
39. Reforming
39
Reforming is a process of bringing about structural modifications in the components of straight run gasoline (prepared
by the fractional distillation of the crude oil), with the primary object of imtproving its anti-knock characteristics.
Thermal Reforming:
Catalytic Reforming:
40. Knocking
40
Knocking is a kind of explosion due to rapid pressure rise occurring in an IC engine
In a petrol engine, a mixture of gasoline vapour and air at 1: 17 ratio is used as fuel. This mixture is compressed and ignited
by an electric spark. The products of oxidation reaction (combustion) increases the pressure and pushes the piston down the
cylinder. If the combustion proceeds in a regular way, there is no problem in knocking. But in some cases, the rate of
combustion (oxidation) will not be uniform due to unwanted chemical constituents of gasoline. The rate of ignition of the fuel
gradually increases and the final portion of the fuel-air mixture gets ignited instantaneously producing an explosive sound
known as "Knocking". Knocking property of the fuel reduces the efficiency of engine. So a good gasoline should resist
knocking.
Chemical structure and knocking
The knocking tendency of fuel hydrocarbons mainly depends on their chemical structures. The knocking tendency
decreases in the following order.
Straight chain paraffins> Branched chain paraffins> Cycloparaffins > Olefins > Aromatics.
Improvement of antiknock characteristics
The octane number of fuel can be improved by
(i) blending petrol of high octane number with petrol of low octane number, so that the octane number of the latter can be
improved.
(ii) the addition of anti-knock agents like Tetra-Ethyl Lead (TEL).
41. Octane rating
41
Octane rating (introduced by Edger in 1872)
It has been found that n-heptane knocks very badly and hence, its anti-knock value has arbitrarily been given zero
On the other hand, isooctane (2,2,4-trimethyl pentane)is having very good anti-knocking properties. Thus octane number is
given 100.
In this way, “80-octane” fuel is one which has the same combustion characteristics as a 80:20 mixture of isooctane and n-
heptane.
42. Anti-Knocking agent
42
LEADED PETROL (ANTI-KNOCK AGENT)
The anti-knock properties of a gasoline can be improved by the addition of suitable additives. Tetraethyl lead (TEL) or
Pb(C2H5)4 is an important additive added to petrol. Thus the petrol containing tetra ethyl lead is called leaded petrol.
TEL reduces the knocking tendency of hydrocarbon.
Knocking follows a free radical mechanism, leading to a chain growth which results in an explosion. If the chains are
terminated before their growth, knocking will cease.
TEL decomposes thermally to form ethyl free radicals which combine with the growing free radicals of knocking process
and thus the chain growth is stopped.
43. Anti-Knocking agent
43
Disadvantages of using TEL
I. When the leaded petrol is used as a fuel, the TEL is converted to lead oxide and metallic lead. This lead deposits on the
spark plug and on cylinder walls which is harmful to engine life. To avoid this, small amount of ethylene dibromide is
added along with TEL. This ethylene dibromide reacts with Pb and PbO to give volatile lead bromide, which goes out
along with exhaust gases.
II. But this creates atmospheric pollution. So nowadays aromatic phosphates are used instead of TEL
III. Nowadays aromatic phosphates are used as antiknock agent because it avoids lead pollution.
44. Unleaded Petrol
44
Octane rating of petrol is in leaded petrol is increased by adding tetra ethyl lead or tetramethyl lead
However, combustion of lead petrol leads to formation of litharge (PbO), which deposition the inner wall of cylinder and
jams the piston.
Also leaded petrol cannot be used in automobiles equipped cost catalytic converter, because lead present in exhaust gas
poisons the catalyst, thereby destroying the active sites
Alternative method of increasing octane number of petrol is to add high octane compounds like isopentane, isooctane,
ethyl benzene, isopropyl benzene, methyl tertiary butyl ether (MTBE). Out of these MTBE is preferred, because it contains
oxygen in the form of ether group and supplies oxygen for the combustion of petrol in internal combustion engines,
thereby reducing the extent of peroxy compound formation
"Unleaded petrol’’ is one where in the enhancement of octane rating is accomplished without the addition of lead
compounds
major advantage of unleaded petrol is that it permits the use of catalytic converter attached to the exhaust in automobiles.
A catalytic converter contains a catalyst (rhodium), which converts the toxic gases (CO and NO) to harmless gases (CO,
and N, respectively). Moreover, it oxidizes unburnt hydrocarbon into CO, and H2O.
46. Fullerene
46
A Fullerene is any molecule composed entirely of carbon, in the form of a hollow sphere, ellipsoid, or tube.
Spherical fullerenes are also called buckyballs, and cylindrical ones are called carbon nanotubes or buckytubes
47. History
47
The existence of C60 was predicted by Eiji Osawa of Toyohashi University of Technology in a Japanese magazine in
1970
With mass spectrometry, discrete peaks were observed corresponding to molecules with the exact mass of sixty or
seventy or more carbon atoms. In 1985, James R. Heath, Robert Curl and Richard Smalley, from Rice University
discovered C60, and shortly thereafter came to discover the fullerenes.
Kroto, Curl, and Smalley were awarded the 1996 Nobel Prize in Chemistry for their roles in the discovery of this
class of compounds.
Minute quantities of the fullerenes, in the form of C60, C70, C76, and C84 molecules, are produced in nature,
hidden in soot and formed by lightning discharges in the atmosphere.
The Icosahedral Fullerene C540
C84 Fullerene
48. Naming
48
Buckminsterfullerene (C60) was named after Richard Buckminster Fuller, a noted architectural modeler
who popularized the geodesic dome.
The shortened name 'fullerene' is used to refer to the family of fullerenes.
The suffix “ene” indicates that each C atom is covalently bonded to three others.
The Montreal Biosphère by Buckminster Fuller, 1967
49. Types of Fullerenes
49
BUCKYBALL CLUSTERS: smallest member is C20 (unsaturated version of dodecahedrane) and the most
common is C60.
NANOTUBES: hollow tubes of very small dimensions, having single or multiple walls; potential applications in
electronics industry.
MEGATUBES: larger in diameter than nanotubes and prepared with walls of different thickness; potentially used for
the transport of a variety of molecules of different sizes.
POLYMERS: chain, two-dimensional and three-dimensional polymers are formed under high-pressure high-
temperature conditions; single-strand polymers are formed using the Atom Transfer Radical Addition Polymerization
(ATRAP) route.
NANO"ONIONS": spherical particles based on multiple carbon layers surrounding a buckyball core; proposed for
lubricants.
LINKED "BALL-AND-CHAIN" DIMERS: two buckyballs linked by a carbon chain.
50. Synthesis of C60
50
The experimental set-up used to discover C60.
The graphite disk is evaporated with a Nd:YAG laser and the evaporated carbon plasma is cooled by a stream of
helium coming from a pulsed valve.
The clusters of carbon are produced in the integration cup and are expanded into vacuum. The ions are detected by
time of flight mass spectrometry
Arc Discharge Method
51. Properties of Fullerene
51
AROMATICITY
Researchers have been able to increase the reactivity of fullerenes by attaching active groups to their
surfaces.
Buckminsterfullerene does not exhibit "superaromaticity": that is, the electrons in the hexagonal rings do
not delocalize over the whole molecule.
CHEMISTRY
• Fullerenes are stable, but not totally unreactive.
• Other atoms can be trapped inside fullerenes to form inclusion compounds known as endohedral
fullerenes.
52. Application of Fullerene
52
The few of the applications of fullerenes are-
A. Artificial photosynthesis
B. Non-linear optics
C. In cosmetics.
D. In surface coatings
E. Bio logical applications
53. Application of Fullerene
53
The few of the applications of fullerenes are-
A. Artificial photosynthesis
B. Non-linear optics
C. In cosmetics.
D. In surface coatings
E. Bio logical applications
54. Application of Fullerene
54
It is a powerful antioxidant, reacting readily and at a high rate with free radicals, which are often the cause
of cell damage or death.
It behaves like a "radical sponge," as it can sponge-up and neutralize 20 or more free radicals per fullerene
molecule.
It possess a novel ability of selectively entering oxidation-damaged cerebral endothelial cells rather than
normal endothelial cells and then protecting them from apoptosis.
55. Polymers
55
Polymers are known to have good insulating properties. (they are used in electrical and electronic
applications as insulators)
Polymers are one of the most used materials in the modern world. Their uses and application range from
containers to clothing.
They are used to coat metal wires to prevent electric shocks.
56. Properties and uses of Polymers
56
Properties
Lightness
Strength
Flexibility
Resistance to Corrosion and chemical attack
Elasticity
Mouldability
Ease of handling
Uses
In space
Aeronautics
Electronics
Non-linear Optics
57. What is conductivity?
57
Conductivity is the ability of a material to pass an electric current.
In a metal the outer electrons are free to carry charge and
the impedance to flow of charge is mainly due to the electrons
"bumping" in to each other.
58. Conducting Polymer: History
58
Alan J. Heeger, Alan G. MacDiarmid and Hideki Shirakawa have changed this view with their discovery
that a polymer, polyacetylene (PA), can be made conductive almost like a metal.
They found that organic conjugated polymers, exhibits dramatic increase in electrical conductivity on
treatment with oxidizing (electron-accepting) or reducing (electron donating) agents.
These oxidation and reduction reactions, which induce high conductivity in PA are termed as p-doping
and n-doping.
59. Instability of PA in air
59
The discovery of highly conducting PA led to sudden research activity directed towards the study of new
conducting polymeric systems as PA was found to be less stable in air
PA get oxidized in presence of air forming new covalent bonds in the form of O2 and CO2 interrupting
double bond conjugation.
Hence less conjugation leads to lowering in conductivity.
61. Conditions for Electrical Conductivity
61
All the previous examples share many structural features like
i. Conjugated backbones
ii. Planarity
iii. Large anisotropy Ratio (i.e. intrachain conductivity is much larger than that of interchain conductivity)
While the enhanced conductivity can be related to the
i. The alignment of polymer chains
ii. The conjugation length
iii. The doping percentage
iv. The purity of sample
62. Conditions for Electrical Conductivity
62
All the previous examples share many structural features like
i. Conjugated backbones
ii. Planarity
iii. Large anisotropy Ratio (i.e. intrachain conductivity is much larger than that of interchain conductivity)
While the enhanced conductivity can be related to the
i. The alignment of polymer chains
ii. The conjugation length
iii. The doping percentage
iv. The purity of sample
63. Conditions for Electrical Conductivity
63
(1) The polymer consists of alternating single and double bonds, called conjugated double bonds.
In conjugation, the bonds between the carbon atoms are alternately single and double. Every bond contains a
localised “sigma” (σ) bond which forms a strong chemical bond. In addition, every double bond also
contains a less strongly localised “pi” (π) bond which is weaker.
64. Conditions for Electrical Conductivity
64
(2) Polymer has to be disturbed - either by removing electrons from (oxidation), or inserting them into
(reduction), the material. (Doping; the role of the dopant is either to remove or to add electrons to the
polymer.)
There are two types of doping:
Oxidation with halogen
Polymer + X (polymer)n+ + Xn-
Reduction with alkali metal
Polymer + M (polymer)n- + Mn+
X= I2, Br2, AsF5……. M = Na, Li……….
65. Doping Process
65
The iodine molecule attracts an electron from the polyacetylene chain and becomes I3-. The
polyacetylene molecule, now positively charged, is termed a radical cation, or polaron.
The lonely electron of the double bond, from which an electron was removed, can move easily. As a
consequence, the double bond successively moves along the molecule. This movement of charge is
what is actually responsible for electrical conductivity.
The positive charge, on the other hand, is fixed by electrostatic attraction to the iodide ion, which does
not move so readily.
66. Conductivity Responsible Species
66
Earlier increase in conductivity observed was initially thought to result from the formation of unfilled
electronic bands.
But this assumption was challenged as in PA and PPP, conductivity is associated with spinless charge
carriers not unpaired electrons
After doping, these polymers are associated with formnation of self-localized excitations such as
solitons, polarons, bypolarons as they move throughout the material freely.
As a result of doping, strong electron-phonon interactions present in these quasi- one dimensional
polymers.
67. Engineering of small band gap polymers
67
The process of doping enhance conductivity but it leads to chemical instability and poor processibility in
them.
So achieving small band gap without using dopant is a challenging process but can be done by applying
following strategies
1. Substitution/Fusion
2. Ladder polymerization
3. Topological methods
4. Copolymerization
5. Donor-Acceptor polymerization
69. Conductivity of typical materials
69
Doped polyacetylene is, e.g., comparable to good conductors such as copper and silver, whereas in its
original form it is a semiconductor.
71. Applications of conductive Polymers
71
Conducting Polymers have many uses. The most documented are as follows:
anti-static substances for photographic film
Corrosion Inhibitors
Compact Capacitors
Anti Static Coating
Electromagnetic shielding for computers "Smart Windows"
Transistors
Light Emitting Diodes (LEDs)
Lasers used in flat televisions
Solar cells
Displays in mobile telephones and mini-format television screens