This document describes an embedded home security system that uses various sensors and components. The system uses an AT89S52 microcontroller along with an IR sensor, LCD display, GSM module, LEDs and other components. The IR sensor detects intruders and the GSM module sends alerts. It provides automated security monitoring and user authentication to prevent break-ins. The system is designed to be effective, practical and reasonably priced for home security.
Home security system is needed for convenience and safety. This system invented to keep home safe from intruder. In this work, we present the design and implementation of a GSM & PIR sensor based home security system using ARDUINO-UNO board. Which take a very less power. The system is a arduino-uno based home security system which contains a GSM modem and PIR sensor with servo-motor and a camera which provides a better security. The system can response rapidly as intruder enters into the trigged zone, PIR sensor sense the object and GSM module will send a notification as a SMS to the registered number of the home owner, and can also give a snapshot of that object. This security system for alerting a house owner wherever he will. In this system as a object enters into the zone GSM module produce a signal through a public telecom network and sends a message or redirect a call that that tells about your home update or predefined message which is embedded in arduino-uno board. Suspected activities are conveyed to remote user through SMS or Call using GSM technology.
This presentation consisting of home automation using bluetooth controol on the basis of Arduino UNO. Arduino is a rapid proto type , that's why we are using this arduino board. This Arduino UNO consisting of a microcontroller namely ATMEGA328. It has both analog and digital I/O pins inorder to communicate with the external peripherals.
Home security system is needed for convenience and safety. This system invented to keep home safe from intruder. In this work, we present the design and implementation of a GSM & PIR sensor based home security system using ARDUINO-UNO board. Which take a very less power. The system is a arduino-uno based home security system which contains a GSM modem and PIR sensor with servo-motor and a camera which provides a better security. The system can response rapidly as intruder enters into the trigged zone, PIR sensor sense the object and GSM module will send a notification as a SMS to the registered number of the home owner, and can also give a snapshot of that object. This security system for alerting a house owner wherever he will. In this system as a object enters into the zone GSM module produce a signal through a public telecom network and sends a message or redirect a call that that tells about your home update or predefined message which is embedded in arduino-uno board. Suspected activities are conveyed to remote user through SMS or Call using GSM technology.
This presentation consisting of home automation using bluetooth controol on the basis of Arduino UNO. Arduino is a rapid proto type , that's why we are using this arduino board. This Arduino UNO consisting of a microcontroller namely ATMEGA328. It has both analog and digital I/O pins inorder to communicate with the external peripherals.
Vehicle anti theft tracking system based on internet of things Jyothsna Sridhar
As the number of urban vehicles are growing rapidly vehicle theft has become an important concern for all vehicle owners.
However present anti theft system lacks the tracking and monitoring system.
The vehicle anti theft tracking System based on Internet of things is proposed which can provide all round service to car owners.
This was one of my Diploma in Engineering Projects.
It's a Voice controlled Home Automation System which works with the Internet. Which means you can control your home appliances from anywhere.
I did the Presentation for the Home Automation System. I was also one of the core team members who made it happen.
Here are the complete powerpoint slides.
Thank You
Arduino based automatic temperature controlled fan speed regulatorEdgefxkits & Solutions
Using an analog temperature LM35 interfaced to the built in ADC of a programmed Arduino to develop varying duty cycle of PWM output for a driver IC to run a DC motor automatically according to the sensed temperature at different speed based on the temperature sensed.
IR BASED HOME AUTOMATION USING ARDUINO UNOMln Phaneendra
In this work, a remote controlled device is used to control 1 - 6 different single phase loads like Fans, Tube Lights and etc.,
This Automation can be operated up to a 30 feet of distance . Our work is based on Infra-Red(IR) technology and a simple Arduino Board(AB) using Printed Circuit Board(PCB).
The new designed circuit is more advantageous as it is portable, easy to carry and use.
Vehicle anti theft tracking system based on internet of things Jyothsna Sridhar
As the number of urban vehicles are growing rapidly vehicle theft has become an important concern for all vehicle owners.
However present anti theft system lacks the tracking and monitoring system.
The vehicle anti theft tracking System based on Internet of things is proposed which can provide all round service to car owners.
This was one of my Diploma in Engineering Projects.
It's a Voice controlled Home Automation System which works with the Internet. Which means you can control your home appliances from anywhere.
I did the Presentation for the Home Automation System. I was also one of the core team members who made it happen.
Here are the complete powerpoint slides.
Thank You
Arduino based automatic temperature controlled fan speed regulatorEdgefxkits & Solutions
Using an analog temperature LM35 interfaced to the built in ADC of a programmed Arduino to develop varying duty cycle of PWM output for a driver IC to run a DC motor automatically according to the sensed temperature at different speed based on the temperature sensed.
IR BASED HOME AUTOMATION USING ARDUINO UNOMln Phaneendra
In this work, a remote controlled device is used to control 1 - 6 different single phase loads like Fans, Tube Lights and etc.,
This Automation can be operated up to a 30 feet of distance . Our work is based on Infra-Red(IR) technology and a simple Arduino Board(AB) using Printed Circuit Board(PCB).
The new designed circuit is more advantageous as it is portable, easy to carry and use.
My Final Year Project - Individual Control Home Automation SystemMichael Olafusi
This project involves the design and construction of an individual control home
automation system using RS232, GSM technology and a microcontroller.
Home automation is the automatic or semi-automatic control and monitoring of
household appliances and residential house features like doors, gate and even the windows.
This project is a demonstration of how to design and build a multi purpose remotely
controlled system that can switch OFF and ON any electrical household appliance (including the security light), by dialling a phone already interfaced via RS232 to a microcontroller that controls a relay for the automatic switching on and off of the appliance and the phone will send a feedback short message service text indicating the new state of the appliance, whether switched ON or OFF.
The results of this project show that a microcontroller is a very powerful device for
building smart electronic devices that can automatically control electrical appliances, with little circuitry complexities and components.
The Home Automation & Security system is a basic model created using Arduino, Raspberry Pi and Relays to Automate the house. It is very basic in nature and is completed as a part of my internship project
Wireless energy meter monitoring with automated tariff calculationUdayalakshmi JK
Electricity billing has become a difficult task. The board has to make regular visit to the consumers house to make the reading. Also it can cause manual error. Now here we are monitoring the energy meter with modern techniques. The total energy consumed by the consumer and the consumption cost is known to the consumer and to the board by means of a hand held device.
Design Efficient Wireless Monitoring Platform for Recycling Point SpotsIJMTST Journal
There is a growing demand for low cost, very low power and reduced size monitoring systems with
wireless communications, to be used in different kinds of industrial environments. In several countries waste
separation and recycling is a major issue. Consequently, the number of recycling spots has been steadily
increasing. In order to ensure that recycle bins are properly maintained, several monitoring solutions have
been proposed. These still have several limitations, such as requiring wires for power and/or communications
and not being able to fit in all existing types of bins. This paper presents WECO, a wireless embedded solution
for monitoring the level of the bins located in recycling spots. The proposed system automatically alerts a
remote central station when a bin reaches a programmable filling level, thus avoiding the need to spot check
if the bin is full and ensuring that the recycling spot is kept clean. The developed prototype required
hardware-software co-design and aimed to meet the above mentioned requirements, resorting to the IEEE
802.15.4 protocol for wireless communications between all nodes in the network, each based on a
System-On-Chip CC2530 from Texas Instruments. Due to its wireless nature, the architecture requires a
battery for power supplying the nodes, with a life time of at least six years. The filling level readings of each
bin in a recycling spot are made using an ultrasonic sensor. The data collected by the monitoring platform is
then sent to the remote central station that processes it in order to optimize routes and establish a scheduled
collection of the recycling spots.
Tracking police man using rf proximity cardAlbert Jose
Security is the important cause in the modern world. Now a day so many schemes have
announced by the banks which very attractive and the people are saving money in banks. At this
point protecting the banks is the main duty of police. Hence police are appointed securities to the
banks and make them to patrol during nights. . They have to go to every banks and streets and
sign the books kept in their places .But some police people forgot their duty and will sleep in a
vacant place and in the morning they get up and in a hurry go to these banks and put a fake time
and date and the signature .To avoid this and to provide more security our proposed system is
giving solution for tracking police man using RF proximity card. A RF proximity card reader with a
microcontroller will be designed and will be placed in every bank. During the patrol time, when a
police man swipe the card it will read the card number and will store it with date and time. The
data can be retrieved by connecting the machine to PC and giving appropriate commands.
Tracking police man using RF proximity card embedded system project explains about
new method for bank officials for checking their security of the bank by implementing accurate
method to control police officials. In present scenario banks are playing important role in providing
security for people for saving their money, gold..Etc. So banks are taking serious steps to
maintain security like hiring police officials at night time for patrolling banks, but there are chances
in irregularity of police officials so this method will provide card system for every police official
who should scratch his card. Data and time is stored inside system which can connect to
computer and analyze details of his attendance
Rotary RFID Parking Management Solution Controlled By MicrocontrollerIJSRD
This paper led emphasis over the automatic parking system. The reason behind this research work is to eradicate the traffic problem arise during the rush hours in day time. Implementation of intelligent parking also helpful in security purpose this research paper is based on RFID based technology along with IR communication. The main governing body is microcontroller. RFID means radio frequency identification, this technology has been used for since last two decades, reason behind this technology is quite straight as it is capable of providing new services and convenience in retail environment. This technology is very reliable as well as very user friendly. This also ease the security purpose, this also reduced time consumption of user. This research involved following components (a) IR based communication, (b) RFID Module, (c) Microcontroller ATmega328.
Rotary RFID Parking Management Solution Controlled By MicrocontrollerIJSRD
This paper led emphasis over the automatic parking system. The reason behind this research work is to eradicate the traffic problem arise during the rush hours in day time. Implementation of intelligent parking also helpful in security purpose this research paper is based on RFID based technology along with IR communication. The main governing body is microcontroller. RFID means radio frequency identification, this technology has been used for since last two decades, reason behind this technology is quite straight as it is capable of providing new services and convenience in retail environment. This technology is very reliable as well as very user friendly. This also ease the security purpose, this also reduced time consumption of user. This research involved following components (a) IR based communication, (b) RFID Module, (c) Microcontroller ATmega328.
Interfacing Of PIC 18F252 Microcontroller with Real Time Clock via I2C ProtocolIJERA Editor
This paper describes a microcontroller based digital clock which can be used in real time systems. The system is constructed using PIC18F252 (microcontroller), DS1307 (real time clock IC) and its software program is written with C programming language. A 3v battery backup is provided to real time clock IC. Communication between PIC microcontroller and DS1307 takes place through I²C Bus protocol
1. 1 | P a g e
NATIONAL INSTITUTE OF TECHNOLOGY
SRINAGAR
A
Seminar Report
On
“EMBEDDED BASED HOME SECURITY SYSTEM”
By
Jitendra Kumar
416/11
dhaka.jiten@gmail.com
DEPARTMENT OF
ELECTRONICS &COMMUNICATION ENGINEERING
2. 2 | P a g e
CONTENTS
Introduction
General Architecture
Various Components
Working
Applications
Advantages
Future Scope
Conclusion
References
3. 3 | P a g e
INTRODUCTION
When we talk about the security the one thing come in mind that whether our home is
secure or not. Our home has always important documents, money and other precious things,
that need to be protected from the intruders or thieves.
In today’s age of digital technology and intelligent systems, home automation has
become one of the fastest developing application-based technologies in the world. The idea of
comfortable living in home has since changed for the past decade as digital, vision and
wireless technologies are integrated into it. Intelligent homes, in simple terms, can be
described as homes that are fully automated in terms of carrying out a predetermined task,
providing feedback to the users, and responding accordingly to situations. In other words, it
simply allows many aspects of the home system such as temperature and lighting control,
network and communications, entertainment system, emergency response and security
monitoring systems to be automated and controlled, both near and at a distance. Automated
security systems play an important role of providing an extra layer of security through user
authentication to prevent break-ins at entry points and also to track illegal intrusions or
unsolicited activities within the vicinity of the home (indoor sand outdoors).
There has been much research done in the design of various types of automated security
systems. Many security systems are based on only a single system. In an event of system
failure or intrusion of the user authentication, there is no backup system to monitor the home
continually. Thus, a feasible system should be effective, practical and reasonable in cost. In
this report, we proposed an integrated based home security system, consisting an IR sensor
and GSM Module.
4. 4 | P a g e
GENERAL ARCHITECTURE
The proposed general architecture incorporates subsystems IR sensors, GSM module
into a single automated architecture for practical implementation in intelligent home
environments. The figure shows a simple architecture diagram of the proposed system and
its setup and connectivity. The modules work independently and parallel but share
computational resources.
Figure-1 Simple Architecture of GSM home security system
5. 5 | P a g e
Overview of Components Used in Architecture
AT89S52 Microcontroller
LCD Display
IR Sensor
GSM Module
LED
MAX232 IC
6. 6 | P a g e
AT89S52 Microcontroller
The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K
bytes of in-system programmable Flash memory. The device is manufactured using Atmel’s
high density non-volatile memory technology and is compatible with the industry standard
80C51 instruction set and pinout. The on-chip Flash allows the program memory to be
reprogrammed in-system or by a conventional non-volatile memory programmer. The Atmel
AT89S52 is a powerful microcontroller which provides a highly-flexible and cost-effective
solution to many embedded control applications. The AT89S52 provides the following
standard features:
Features
8K bytes of Flash,
256 bytes of RAM,
32 I/O lines, Watchdog timer,
2 data pointers,
Three 16-bit timer/counters,
A six-vector two-level interrupt architecture,
A full duplex serial port,
On-chip oscillator,
4.0V to 5.5V Operating Range
7. 7 | P a g e
Pin Diagram
The 8051 microcontroller consists of 40 pins. These pins are well represented by the pin
diagram below.
Figure- 2 Pin Diagram of 8052 Microcontroller
8. 8 | P a g e
Pin Description
Pin No Function Name
1 External count input to Timer/Counter 2, clock-out T2 P1.0
Timer/Counter 2 capture/reload trigger and direction
2
control
T2 EX P1.1
3
8 bit input/output port (P1) pins
P1.2
4 P1.3
5 P1.4
6 P1.5
7 P1.6
8 P1.7
9 Reset pin; Active high Reset
10
Input (receiver) for serial
communication
RxD
8 bit input/output
port (P3) pins
P3.0
11
Output (transmitter) for serial
communication
TxD P3.1
12 External interrupt 1 Int0 P3.2
13 External interrupt 2 Int1 P3.3
14 Timer1 external input T0 P3.4
15 Timer2 external input T1 P3.5
16 Write to external data memory Write P3.6
17 Read from external data memory Read P3.7
18
Quartz crystal oscillator (up to 24 MHz)
Crystal 2
19 Crystal 1
20 Ground (0V) Ground
21
8 bit input/output port (P2) pins
/
High-order address bits when interfacing with external memory
P2.0/ A8
22 P2.1/ A9
23 P2.2/ A10
24 P2.3/ A11
25 P2.4/ A12
26 P2.5/ A13
27 P2.6/ A14
28 P2.7/ A15
29 Program store enable; Read from external program memory PSEN
30
Address Latch Enable ALE
Program pulse input during Flash programming Prog
31
External Access Enable; Vcc for internal program executions EA
Programming enable voltage; 12V (during Flash programming) Vpp
32
8 bit input/output port (P0) pins
Low-order address bits when interfacing with external memory
P0.7/ AD7
33 P0.6/ AD6
34 P0.5/ AD5
35 P0.4/ AD4
36 P0.3/ AD3
37 P0.2/ AD2
38 P0.1/ AD1
39 P0.0/ AD0
40 Supply voltage; 5V (up to 6.6V) Vcc
9. 9 | P a g e
Internal Block Diagram of 8051 Microcontroller
Figure-3 Internal block diagram of 8051 Microcontroller
Memory Architecture
The 8051 has two types of memory and these are Program Memory and Data Memory. All
8051 microcontrollers have a 16-bit addressing bus and are capable of addressing 64 kb
memory.
Program Memory: - Program Memory (ROM) is used to permanently save the program
being executed
Data Memory: - Data Memory is used for temporarily storing data and intermediate results
created and used during the operation of the microcontroller
10. 10 | P a g e
Figure-4 Memory Banks in 8051 Microcontroller
Special Function Registers (SFRs)
Special Function Registers (SFRs) are a sort of control table used for running and monitoring
the operation of the microcontroller.
A Register (Accumulator)
A register is a general-purpose register used for storing intermediate results obtained during
operation. Data to be moved from one register to another must go through the
accumulator. In other words, the A register is the most commonly used register and it is
impossible to imagine a microcontroller without it.
B Register
Multiplication and division can be performed only upon numbers stored in the A and B
registers. All other instructions in the program can use this register as a spare accumulator.
11. 11 | P a g e
Liquid Crystal Display (LCD)
A liquid crystal display (LCD) is a thin, flat electronic visual display that uses the light
modulating properties of liquid crystals (LCs). They are used in a wide range of applications,
including computer monitors, television, instrument panels, aircraft cockpit displays etc.
They are common in consumer devices such as video players, gaming devices, clocks,
watches, calculators, and telephones. LCDs have displaced cathode ray tube (CRT) displays
in most applications. They are usually more compact, lightweight, portable, less expensive,
more reliable, and easier on the eyes. They are available in a wider range of screen sizes
than CRT. LCDs are more energy efficient and offer safer disposal than CRTs. Its low
electrical power consumption enables it to be used in battery powered electronic
equipment.
Figure-5 LCD
12. 12 | P a g e
Infra-Red Sensor (IR Sensor)
The basic principle of IR sensor is based on an IR emitter and an IR receiver. IR emitter
will emit infrared continuously when power is supplied to it. On the other hand, the IR
receiver will be connected and perform the task of a voltage divider. IR receiver can be
imagined as a transistor with its base current determined by the intensity of IR light
received. The lower the intensity of IR light cause higher resistance between collector-emitter
terminals of transistor, and limiting current from collector to emitter. This change of
resistance will further change the voltage at the output of voltage divider. In others word,
the greater the intensity of IR light hitting IR receiver, the lower the resistance of IR receiver
and hence the output voltage of voltage divider will decreased. The further distance away
between emitter and receiver decrease the amount of infrared light hitting the receiver if
the distance between the sensor and a reflective surface is fixed.
Figure- 6 infrared sensor
Infrared radiation is the portion of electromagnetic spectrum having wavelengths longer
than visible light wavelengths, but smaller than microwaves, i.e., the region roughly from
0.75μm to 1000 μm is the infrared region. Infrared waves are invisible to human eyes. The
wavelength region of 0.75μm to 3 μm is called near infrared, the region from 3 μm to 6 μm
is called mid infrared and the region higher than 6 μm is called far infrared. (The
demarcations are not rigid; regions are defined differently by many).
13. 13 | P a g e
Voltage Regulator
A Voltage Regulator is an electrical regulator designed to automatically maintain a
constant voltage level. Depending on the design, it may be used to regulate one or more AC
or DC voltages. A basic voltage regulator LM7805 has three legs, converts varying input
voltage and produces a constant regulated output voltage.
Figure-7 Voltage Regulator
14. 14 | P a g e
Light Emitting Diodes (LED’s)
LEDs present many advantages over incandescent light sources including lower energy
consumption, longer lifetime, improved robustness, smaller size, faster switching, and
greater durability and reliability. LEDs powerful enough for room lighting are relatively
expensive and require more precise current and heat management than compact
fluorescent lamp sources of comparable output.
.
Figure-8 Light-Emitting Diodes (LED‟s)
15. 15 | P a g e
GSM Module
GSM (Global System for Mobile) / GPRS (General Packet Radio Service) TTL –Modem is
SIM900 Quad-band GSM / GPRS device, works on frequencies 850 MHZ, 900 MHZ, 1800
MHZ and 1900 MHZ. It is very compact in size and easy to use as plug in GSM Modem. The
Modem is designed with 3V3 and 5V DC. TTL interfacing circuitry, which allows User to
directly interface with 5V Microcontrollers (PIC, AVR, Arduino, 8051, etc.) as well as 3V3
Microcontrollers (ARM, ARM Cortex XX, etc.). The baud rate can be configurable from 9600-
115200 bps through AT (Attention) commands. This GSM/GPRS TTL Modem has internal
TCP/IP stack to enable User to connect with internet through GPRS feature. It is suitable for
SMS as well as DATA transfer application in mobile phone to mobile phone interface. The
modem can be interfaced with a Microcontroller using USART (Universal Synchronous
Asynchronous Receiver and Transmitter) feature (serial communication).
Figure-9 GSM Module
16. 16 | P a g e
Features
Quad Band GSM/GPRS : 850 / 900 / 1800 / 1900 MHz
Built in RS232 to TTL or vice versa Logic Converter (MAX232)
Configurable Baud Rate
Built in Network Status LED
Input Voltage : 5V to 12V D
MAX232 IC
The MAX232 is an integrated circuit that converts signals from an RS-232 serial port to
signals suitable for use in TTL compatible digital logic circuits, so that devices works on TTL
logic can share the data with devices connected through Serial port.
Figure-10 MAX232 IC
Serial port / DB9 connector:
User just needs to attach RS232 cable here so that it can be connected to devices which
have Serial port / DB9 Connector.
17. 17 | P a g e
SIM (Subscriber Identity Module) Card Slot:
This on board SIM card slot provides User functionality of insert a SIM (GSM only)
card of any service provider. Process of inserting and locking SIM card into SIM card slot is
given in this manual. While inserting in and removing out SIM card from SIM card slot, User
needs to take precaution that power supply should be OFF so that after making Power supply
ON it will be easy to reinitialize with SIM for this module.
Figure-11 SIM Slot
18. 18 | P a g e
Circuitry in proper way
Figure- 12 GSM Based Home Security System
19. 19 | P a g e
WORKING
Working of GSM Home Security System
Home/ Bank/ Office security has been a major issue where crime is increasing and
everybody wants to take proper measures to prevent intrusion. In addition there was a need to
automate home so that user can take advantage of the technological advancement in such a
way that a person getting off the office does not get melted with the hot climate.
Detecting Obstacle with IR (Infrared) Sensor
The basic concept of IR (infrared) obstacle detection is to transmit the IR signal
(radiation) in a direction and a signal is received at the IR receiver when the IR radiation
bounces back from a surface of the object.
Figure- 13 IR Sensor Detection Process
Here in the figure the object can be anything which has certain shape and size, the IR
LED transmits the IR signal on to the object and the signal is reflected back from the surface
of the object. The reflected signals are received by an IR receiver. The IR receiver can be a
photodiode /photo transistor or a readymade module which decodes the signal. In order to
implement the IR obstacle detection, we need to understand the following.
We need to understand how to transmit IR signal using commercially available
electronic components.
Same way we also need to understand the IR receiver.
20. 20 | P a g e
IR Transmitter
In general, the basic building block of any IR transmitter is modulation of the
information signal with carrier signal, because the receiver modules which are available off-the-
shelf are made for a particular carrier frequency. So it is clear that when you chose a
particular IR receiver module, you also need to transmit the modulated wave with the same
carrier frequency of that of an IR receiver module.
IR Receiver
It is quite simple to construct an IR receiver with readily available off-the-shelf
modules. These modules are nothing but the IC packages, referred as TSOP (Thin small-outline
package). In this document, the receiver is designed for 38 kHz carrier signal; hence
the IC selected should work for the same frequency. The IC TSOP4838 will serve as a
receiver module, which is compatible with both TTL and CMOS logic. This means that we
can directly get digital signal from the receiver module and then connect it to the
microcontroller.
Once the transmitter and receiver is complete, both should be placed at a certain angle,
so that the obstacle detection happens in a proper way. This angle is nothing but the
directivity of the sensor, which is generally +/- 45 degrees.
Figure -14 IR Directivity
21. 21 | P a g e
Also remember, that a thick enclosure is necessary for both IR transmitter and IR
receiver, because the IR radiation may bounce back from the surrounding objects which may
not help when you want to detect obstacle in one direction. Sometimes, if you don’t have a
thick enclosure then the signal may directly reach the receiver even without having an
obstacle.
Working of GSM Module
The GSM modem is slightly different from the conventional modem. This utilizes the
GSM standard for cellular technology. Here, one end being a wired connection, receives and
transmits data. The other end is connected to a RF antenna. The GSM modem acts like a
cellular phone and transmits text and voice data. It communicates with the GSM network via
the SIM (Subscriber’s Identity Module) card. The Global System for Mobile
Communications (GSM: originally from Grouper Special Mobile) is the most popular
standard for mobile phones in the world. GSM differs significantly from its predecessors in
that both signalling and speech channels are Digital call quality, which means that it is
considered a second generation (2G) mobile phone system. This fact has also meant that data
communication was built into the system from the 3rd Generation Partnership Project
(3GPP).
When any object is detected by IR sensor then it sends the command to the
microcontroller and now microcontroller send the command to the GSM module .GSM
module have a SIM card, with the help of SIM card GSM module send the SMS on give
mobile number which is already programmed in the microcontroller
22. 22 | P a g e
Application
The applications of SMS/GSM Based security system are quite diverse. There are
many real life situations that require control of different devices remotely and to provide
security. There will be instances where a wired connection between a remote
appliance/device and the control unit might not be feasible due to structural problems. Major
areas where it is used as
Anti-Theft Reporting
When someone break in , Home-Guard uses GSM network to report automatically to 5
pre-set numbers: short message for control centre, short message for 3 pre-stored mobile
phone, and 1 voice call. The owner can monitor or talk to the thief.
It has 8 security region codes. We can choose some certain regions to arm or disarm.
Emergency Reporting
Under emergency situation, the house member can press SOS key on the RF remote or on
wireless Door/ Window sensor. Home-Guard also uses GSM network to report to 5 pre stored
numbers: short message for control centre, short message for 3 pre-stored mobile phone, and
1 voice call for monitoring or talking phone.
Arm/Disarm By SMS
In addition to use the RF Remote, the system allows the users to arm and disarm the
alarm system via SMS message from mobile phone. Users can also check the alarm status
anytime by simply sending an inquiry SMS message to the main unit.
Power Failure Reporting
When the main power gets cut off, Home-Guard can report to the pre-set phone numbers
immediately.
23. 23 | P a g e
Advantages
Worldwide Roaming: - The user can get alerts anywhere through the GSM
technology thus making the system location independent.
The system contains low cost components easily available which cuts down the
overall system cost.
The ease of deployment is due to wireless mode of communication.
GSM technology provides the benefit that the system is accessible in remote areas as
well.
The system integration is simple and is also scalable and extensible. However, the
system functionality is based on GSM technology so the techno-logical constraints
must be kept in mind
FUTURE SCOPE
In future the system will be small box combining the PC and GSM modem. The
hardware will be self-contained and cannot be prone to electric failure. This appliance will
have its own encapsulated UPS and charging system.
24. 24 | P a g e
CONCLUSION
Low cost, secure, ubiquitously accessible, auto-configurable, remotely controlled
solution for automation of homes has been introduced. GSM technology capable solution has
proved to be controlled remotely, provide home security and is cost-effective as compared to
the previously existing systems. The basic level of home appliance control and remote
monitoring has been implemented.
25. 25 | P a g e
REFERENCES
Mazidi, “The 8051 Microcontroller and Embedded Systems.
http://www.gsm-modem.de/gsm-module.html
http://www.gsm-modem.de/gsm-module.html
http://www.atmel.com/devices/at89s52.aspx