In the past few years the growing demand for electricity and serious concern
for the environment have given rise to the growth of sustainable sources like
wind, solar, tidal, biomass etc. The technological advancement in power
electronics has led to the extensive usage of solar power. Solar power output
varies with the weather conditions and under shading conditions. With the
increasing concerns of the impacts of the high penetration of Photovoltaic
(PV) systems, a technical study about their effects on the power quality of
the utility grid is required. This paper investigates the functioning of a gridtied
PV system along with maximum power point tracking (MPPT)
algorithm. The effects of varying atmospheric conditions like solar irradiance
and temperature are also taken into account. It is proposed in this work that
an Electric Vehicle (EV) can be used as an energy storage to stabilize the
power supplied to the grid from the photovoltaic resources. A coordinated
control is necessary for the EV to obtain desired outcome. The modeling of
the PV and EV system is carried out in PSCAD and the proposed idea is
verified through simulation results utilizing real field data for solar irradiance
and temperature.
Modeling, Control and Power Management Strategy of a Grid connected Hybrid En...IJECEIAES
This paper presents the detailed modeling of various components of a grid connected hybrid energy system (HES) consisting of a photovoltaic (PV) system, a solid oxide fuel cell (SOFC), an electrolyzer and a hydrogen storage tank with a power flow controller. Also, a valve controlled by the proposed controller decides how much amount of fuel is consumed by fuel cell according to the load demand. In this paper fuel cell is used instead of battery bank because fuel cell is free from pollution. The control and power management strategies are also developed. When the PV power is sufficient then it can fulfill the load demand as well as feeds the extra power to the electrolyzer. By using the electrolyzer, the hydrogen is generated from the water and stored in storage tank and this hydrogen act as a fuel to SOFC. If the availability of the power from the PV system cannot fulfill the load demand, then the fuel cell fulfills the required load demand. The SOFC takes required amount of hydrogen as fuel, which is controlled by the PID controller through a valve. Effectiveness of this technology is verified by the help of computer simulations in MATLAB/SIMULINK environment under various loading conditions and promising results are obtained.
Load frequency control of a two area hybrid system consisting of a grid conne...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
This paper describes the Grid connected solar photovoltaique system using DC-DC boost converter and the DC/AC inverter (VSC) to supplies electric power to the utility grid. The model contains a representation of the main components of the system that are two solar arrays of 100 kW, boost converter and the grid side inverter. The paper starts with a system description, in this part we have given a definition and a short overview of every component used in this system and they are taken separately. The PV cell model is easy, accurate, and takes external temperature and solar radiation into consideration. It also proposes a maximum power point tracking (MPPT) algorithm. The algorithm incorporated in a DC/DC converter is used to track the maximum power of PV cell. Finally, the DC/AC inverter (VSC) of three- level is used to regulate the ouput voltage of DC/DC converter and connects the PV cell to the grid. Simulation results show how a solar radiation’s change can affect the power output of any PV system, also they show the control performance and dynamic behavior of the grid connected photovoltaic system.
Measurement and Analysis of Power in Hybrid Systemijeei-iaes
Application with renewable energy sources such as solar cell array, wind turbines, or fuel cells have increased significantly during the past decade. To obtain the clean energy, we are using the hybrid solar-wind power generation. Consumers prefer quality power from suppliers. The quality of power can be measured by using parameters such as voltage sag, harmonic and power factor. To obtain quality power we have different topologies. In our paper we present a new possible topology which improves power quality. This paper presents modeling analysis and design of a pulse width modulation voltage source inverter (PWM-VSI) to be connected between sources, which supplies energy from a hybrid solar wind energy system to the ac grid. The objective of this paper is to show that, with an adequate control, the converter not only can transfer the dc from hybrid solar wind energy system, but also can improve the power factor and quality power of electrical system. Whenever a disturbance occurs on load side, this disturbance can be minimized using open loop and closed loop control systems.
Control for Grid Connected and Intentional Islanding of Distributed Power Gen...ijtsrd
As the demand for more reliable and secure power system with greater power quality increases, the concept of distributed generation DG have become more popular. This popularity of DG concept has developed simultaneously with the decrease in manufacturing costs associated with clean and alternative technologies like fuel cells, biomass, micro turbine and solar cell systems. Intentional islanding is the purposeful sectionalisation of the utility system during widespread disturbances to create power “islandâ€. This island can be designed to maintain a continuous supply of power during disturbances of the main distribution system. Ruchali Borkute | Nikita Malwar ""Control for Grid Connected and Intentional Islanding of Distributed Power Generation"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-4 , June 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23679.pdf
Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/23679/control-for-grid-connected-and-intentional-islanding-of-distributed-power-generation/ruchali-borkute
Modeling, Control and Power Management Strategy of a Grid connected Hybrid En...IJECEIAES
This paper presents the detailed modeling of various components of a grid connected hybrid energy system (HES) consisting of a photovoltaic (PV) system, a solid oxide fuel cell (SOFC), an electrolyzer and a hydrogen storage tank with a power flow controller. Also, a valve controlled by the proposed controller decides how much amount of fuel is consumed by fuel cell according to the load demand. In this paper fuel cell is used instead of battery bank because fuel cell is free from pollution. The control and power management strategies are also developed. When the PV power is sufficient then it can fulfill the load demand as well as feeds the extra power to the electrolyzer. By using the electrolyzer, the hydrogen is generated from the water and stored in storage tank and this hydrogen act as a fuel to SOFC. If the availability of the power from the PV system cannot fulfill the load demand, then the fuel cell fulfills the required load demand. The SOFC takes required amount of hydrogen as fuel, which is controlled by the PID controller through a valve. Effectiveness of this technology is verified by the help of computer simulations in MATLAB/SIMULINK environment under various loading conditions and promising results are obtained.
Load frequency control of a two area hybrid system consisting of a grid conne...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
This paper describes the Grid connected solar photovoltaique system using DC-DC boost converter and the DC/AC inverter (VSC) to supplies electric power to the utility grid. The model contains a representation of the main components of the system that are two solar arrays of 100 kW, boost converter and the grid side inverter. The paper starts with a system description, in this part we have given a definition and a short overview of every component used in this system and they are taken separately. The PV cell model is easy, accurate, and takes external temperature and solar radiation into consideration. It also proposes a maximum power point tracking (MPPT) algorithm. The algorithm incorporated in a DC/DC converter is used to track the maximum power of PV cell. Finally, the DC/AC inverter (VSC) of three- level is used to regulate the ouput voltage of DC/DC converter and connects the PV cell to the grid. Simulation results show how a solar radiation’s change can affect the power output of any PV system, also they show the control performance and dynamic behavior of the grid connected photovoltaic system.
Measurement and Analysis of Power in Hybrid Systemijeei-iaes
Application with renewable energy sources such as solar cell array, wind turbines, or fuel cells have increased significantly during the past decade. To obtain the clean energy, we are using the hybrid solar-wind power generation. Consumers prefer quality power from suppliers. The quality of power can be measured by using parameters such as voltage sag, harmonic and power factor. To obtain quality power we have different topologies. In our paper we present a new possible topology which improves power quality. This paper presents modeling analysis and design of a pulse width modulation voltage source inverter (PWM-VSI) to be connected between sources, which supplies energy from a hybrid solar wind energy system to the ac grid. The objective of this paper is to show that, with an adequate control, the converter not only can transfer the dc from hybrid solar wind energy system, but also can improve the power factor and quality power of electrical system. Whenever a disturbance occurs on load side, this disturbance can be minimized using open loop and closed loop control systems.
Control for Grid Connected and Intentional Islanding of Distributed Power Gen...ijtsrd
As the demand for more reliable and secure power system with greater power quality increases, the concept of distributed generation DG have become more popular. This popularity of DG concept has developed simultaneously with the decrease in manufacturing costs associated with clean and alternative technologies like fuel cells, biomass, micro turbine and solar cell systems. Intentional islanding is the purposeful sectionalisation of the utility system during widespread disturbances to create power “islandâ€. This island can be designed to maintain a continuous supply of power during disturbances of the main distribution system. Ruchali Borkute | Nikita Malwar ""Control for Grid Connected and Intentional Islanding of Distributed Power Generation"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-4 , June 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23679.pdf
Paper URL: https://www.ijtsrd.com/engineering/electrical-engineering/23679/control-for-grid-connected-and-intentional-islanding-of-distributed-power-generation/ruchali-borkute
Design and simulation of stand alone integrated renewable energy system for r...eSAT Journals
Abstract
Present day guided weapon systems, especially tactical class missiles use RF seeker, for target tracking towards terminal engagement. The seeker system including its antenna assembly will be onboard the missile. Due to the missile trajectory corrections, the seeker antenna pointing to the target may get disturbed resulting in track loss. To avoid this track loss, it becomes necessary to stabilize the antenna system in two planes. The fundamental role of stabilization loop in seeker application is to precisely follow the angular rate of the target. In order to achieve this requirement, it is essential to highly isolate the gimbaled antenna from the missile body motion due to the maneuvering of target or low frequency vibration during flight. However, the isolation ratio and stability margin of stabilization loop adopting the gimbaled platform with both low stiffness and heavy inertia are limited by mechanical characteristic such as low resonance frequency and its high magnitude. The selection of proper feedback sensors, modeling of the total system are key features of this project. In the end, the performance and the stability of designed stabilization loop are demonstrated using simulation in both frequency and time domain. The Hardware for the system is under realization by the Industry. The whole scheme is simulated in MATLAB off-line for this project.
Keywords: Missile, RF seeker, Track loss, Stabilization loop, Angular Rate Command, Bore-Sight Error, Maneuvering and Gimbaled Platform.
Control Strategy for Distributed Integration of Photovoltaic and Battery Ener...TELKOMNIKA JOURNAL
The micro-grid deployments are growing with independently, power system designers,
manufacturers and researchers for the applications where the loads are more efficient association with
extra output sources such as Battery Energy Storage System (BESS), and Photovoltaic (PV) systems.
Using renewable source as main sources for micro-grid system also can avoid from the pollution to occur.
Energy storage when combined with PV system can provide a stronger economic performance, as well as
an added benefit of backup power for critical loads. This project proposed control strategies for integration
of BESS and PV in a micro-grid. The operation enables the maximum PV and BESS utilization during
different operating condition of the micro-grid, grid connected, islanded mode or a process between these
two operations. The project will focus on analyzing the performance between photovoltaic system and
battery in the simulations of micro-grids system and validate the simulation result using
MATLAB/SIMULINK software. After the simulation was analyzed, the understanding of benefit in using
renewable energy source as main power supply with support from battery energy storage to supply the
power to the loads and power managements is realized in the different modes on micro-grid which is grid
connected or islanded states. When the power generation from PV system was not enough to
accommodate electric loads, the BESS or from secondary side of transformer will supply the insufficient
power.
In a distributed generation system, divers renewable agents are connected to the low voltage 3 phase utility grid by an inverter which is used as power condition and must assurance the higher efficiency of the renewable agent. To achieve this level of efficiency, a unitary power factor between the utility grid voltages and the inverter currents is necessary, and a synchronization algorithm is required for the perfect synchronization between the 3-phase utility grid and the renewable agent. The aim of this paper is to present the optimization of the performance of a Synchronization controller for a 3-phase photovoltaic grid-connected system, assessing its accuracy under different conditions and studying their drawbacks and advantages. A grid connected photovoltaic system with a nominal power of 5 kW is used so as to assess the behavior of the synchronization algorithm when the 3 phase utility grid is affected by some disturbances such as voltage unbalances.
Simulation of Optimal Control Strategy for a Solar Photovoltaic Power Systemijtsrd
This paper proposes a single stage PV system based on a linear quadratic regulator LQR . The system makes use of a single phase power converter connected to the grid connected system through an LCL filter. The PandO algorithm is used to generate the reference signal for the fluctuating dc bus voltage as well as to extract the maximum power from the solar panels. The proposed work has been carried out in MATLAB, and the results are presented. C. B. Sree Hara Vamsi | B. Kumar Reddy "Simulation of Optimal Control Strategy for a Solar Photovoltaic Power System" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-1 , December 2019, URL: https://www.ijtsrd.com/papers/ijtsrd29786.pdf Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/29786/simulation-of-optimal-control-strategy-for-a-solar-photovoltaic-power-system/c-b-sree-hara-vamsi
Enhancement of On-grid PV System under Irradiance and Temperature Variations ...IJECEIAES
Solar Energy is one of the key solutions to future electrical power generation. Photovoltaic Plants (PV) are fast growing to satisfy electrical power demand. Different maximum power point tracking techniques (MPPT) are used to maximize PV systems generated power. In this paper, on grid PV system model in MATLAB SIMULINK is tested under sudden irradiance and cell temperature variations. Incremental Conductance MPPT is used to maximize generated power from the PV system with the help of new adaptive controller to withstand these heavy disturbances. The new adaptive controller is tuned for optimal operation using two different optimization techniques (Invasive weed and Harmony search).Optimization results for the two techniques are compared. .A robustness test is made to check system stability to withstand different random irradiance and cell temperature patterns without failure to track the maximum power point. Finally, a brief comparison is made with a previous literature and the new adaptive controller gives better results.
Intelligent controller based power quality improvement of microgrid integrati...IJECEIAES
Now a day the power demand has a major problem for developing countries due to the growth of population, industries, IT companies and other needs. In this present situation the fossil fuel-based power generation alone does not support the consumer needs, poor power quality due to nonlinear function and very harmful for environment. The main objective of this paper is improving the power quality of grid connected photovoltaic power system through a new cascade H-bridge multilevel inverter. The proposed research work has been modelled and controlled by ANFIS intelligence in MATLAB simulation environment. The simulation results are analysed under various operating conditions for improve the performance of proposed system. Finally, the proposed system THD value of simulation results is compared with IEEE 1547 standard for prove the effectiveness of proposed research work.
Fuzzy Sliding Mode Control for Photovoltaic SystemIJPEDS-IAES
In this study, a fuzzy sliding mode control (FSMC) based maximum power point tracking strategy has been applied for photovoltaic (PV) system. The key idea of the proposed technique is to combine the performances of the fuzzy logic and the sliding mode control in order to improve the generated power for a given set of climatic conditions. Different from traditional sliding mode control, the developed FSMC integrates two parts. The first part uses a fuzzy logic controller with two inputs and 25 rules as an equivalent controller while the second part is designed for an online adjusting of the switching controller’s gain using a fuzzy tuner with one input and one output. Simulation results showed the effectiveness of the proposed approach achieving maximum power point. The fuzzy sliding mode (FSM) controller takes less time to track the maximum power point, reduced the oscillation around the operating point and also removed the chattering phenomena that could lead to decrease the efficiency of the photovoltaic system.
ENERGY MANAGEMENT SYSTEM FOR CRITICAL LOADS USING POWER ELECTRONICSrenukasningadally
The work aims at an Energy Management System (EMS) for Critical loads using Power Electronics. Here hybrid power sources (Grid and Solar cells) with battery have been used to supply the power to the critical loads at all times, suppose an end user increases his critical loads or non-critical loads this EMS system helps to maintain continuous power supply to these loads. Solar or Photovoltaic cells have been used for storing energy through battery and these batteries will discharge the stored energy at two conditions, one is when grid is shut down for short duration or for a long duration and another one is when there sudden increase in load by users
SALIENT FEATURES OF GRID-CONNECTED PHOTOVOLTAIC SYSTEM AND ITS IMPACT ON POWE...Editor IJMTER
Solar energy is available to the world for free of cost from millions of years and it is a
basic energy source to the mankind. It is also one of largest energy source to the mankind. PV
systems are a relative new technology. The operational experience with PV systems itself is at an
acceptable high level and today’s installed PV systems are of a good quality and are able to operate
without any problems for many years. The price level of the PV modules and the Balance of System
costs (inverter included) have decreased significantly. This energy is available all around the world
in large quantity. When this energy is collected by the solar PV cells it is in the small power with the
D.C. supply, which is not compatible with the existing grid in the world. There is an inverter and the
converter stage comes before this energy can used. Grid interactive PV systems can vary
substantially in size.
Performance Comparison of PID and Fuzzy Controllers in Distributed MPPTIJPEDS-IAES
With an increase of Green Technology applications, Photovoltaic have
emerged as the most appropriate solution for electricity generation purposes.
However, due to variable temperature and irradiance, under the partial or
shaded conditions Maximum Power Point Tracking is needed to determine
highest efficiency of the system. The paper describes dynamic modeling and
control of variable temperature and irradiance on solar panel in SIMULINKMATLAB
environment. The implementation of Buck Converter is used for
power switching and impedance matching on connecting the panel to the
load. The effectiveness of the model, with enhanced efficiency through
voltage stabilization, is performed using Proportional-Integral-Derivative and
Fuzzy-Logic-Controllers. A comparative study is made for PID and FLC on
the basis of outputs to deal with online set point variations. FLC gives closer
results to Standard Test Conditions when compared with PID. The Fuzzy
system developed, using tested membership functions serve as a platform for
sustainable standalone and grid-based applications using distributed MPPT.
This paper addresses the problem of controlling three-phase grid connected PV system involving a PV arrays, a voltage source inverter, a grid filter and an electric grid. This paper presents three main control objectives: i) ensuring the Maximum power point tracking (MPPT) in the side of PV panels, ii) guaranteeing a power factor unit in the side of the grid, iii) and ensuring the asymptotic stability of the closed loop system. Interestingly, the present study features the achievement of the above energetic goal without resorting to sensors of currents of the grid. To this end, an output-feedback control strategy combining a state observer and a nonlinear control laws is developed. The proposed output-feedback control strategy is backed by a formal analysis showing that all control objectives are actually achieved.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Design and simulation of stand alone integrated renewable energy system for r...eSAT Journals
Abstract
Present day guided weapon systems, especially tactical class missiles use RF seeker, for target tracking towards terminal engagement. The seeker system including its antenna assembly will be onboard the missile. Due to the missile trajectory corrections, the seeker antenna pointing to the target may get disturbed resulting in track loss. To avoid this track loss, it becomes necessary to stabilize the antenna system in two planes. The fundamental role of stabilization loop in seeker application is to precisely follow the angular rate of the target. In order to achieve this requirement, it is essential to highly isolate the gimbaled antenna from the missile body motion due to the maneuvering of target or low frequency vibration during flight. However, the isolation ratio and stability margin of stabilization loop adopting the gimbaled platform with both low stiffness and heavy inertia are limited by mechanical characteristic such as low resonance frequency and its high magnitude. The selection of proper feedback sensors, modeling of the total system are key features of this project. In the end, the performance and the stability of designed stabilization loop are demonstrated using simulation in both frequency and time domain. The Hardware for the system is under realization by the Industry. The whole scheme is simulated in MATLAB off-line for this project.
Keywords: Missile, RF seeker, Track loss, Stabilization loop, Angular Rate Command, Bore-Sight Error, Maneuvering and Gimbaled Platform.
Control Strategy for Distributed Integration of Photovoltaic and Battery Ener...TELKOMNIKA JOURNAL
The micro-grid deployments are growing with independently, power system designers,
manufacturers and researchers for the applications where the loads are more efficient association with
extra output sources such as Battery Energy Storage System (BESS), and Photovoltaic (PV) systems.
Using renewable source as main sources for micro-grid system also can avoid from the pollution to occur.
Energy storage when combined with PV system can provide a stronger economic performance, as well as
an added benefit of backup power for critical loads. This project proposed control strategies for integration
of BESS and PV in a micro-grid. The operation enables the maximum PV and BESS utilization during
different operating condition of the micro-grid, grid connected, islanded mode or a process between these
two operations. The project will focus on analyzing the performance between photovoltaic system and
battery in the simulations of micro-grids system and validate the simulation result using
MATLAB/SIMULINK software. After the simulation was analyzed, the understanding of benefit in using
renewable energy source as main power supply with support from battery energy storage to supply the
power to the loads and power managements is realized in the different modes on micro-grid which is grid
connected or islanded states. When the power generation from PV system was not enough to
accommodate electric loads, the BESS or from secondary side of transformer will supply the insufficient
power.
In a distributed generation system, divers renewable agents are connected to the low voltage 3 phase utility grid by an inverter which is used as power condition and must assurance the higher efficiency of the renewable agent. To achieve this level of efficiency, a unitary power factor between the utility grid voltages and the inverter currents is necessary, and a synchronization algorithm is required for the perfect synchronization between the 3-phase utility grid and the renewable agent. The aim of this paper is to present the optimization of the performance of a Synchronization controller for a 3-phase photovoltaic grid-connected system, assessing its accuracy under different conditions and studying their drawbacks and advantages. A grid connected photovoltaic system with a nominal power of 5 kW is used so as to assess the behavior of the synchronization algorithm when the 3 phase utility grid is affected by some disturbances such as voltage unbalances.
Simulation of Optimal Control Strategy for a Solar Photovoltaic Power Systemijtsrd
This paper proposes a single stage PV system based on a linear quadratic regulator LQR . The system makes use of a single phase power converter connected to the grid connected system through an LCL filter. The PandO algorithm is used to generate the reference signal for the fluctuating dc bus voltage as well as to extract the maximum power from the solar panels. The proposed work has been carried out in MATLAB, and the results are presented. C. B. Sree Hara Vamsi | B. Kumar Reddy "Simulation of Optimal Control Strategy for a Solar Photovoltaic Power System" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-4 | Issue-1 , December 2019, URL: https://www.ijtsrd.com/papers/ijtsrd29786.pdf Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/29786/simulation-of-optimal-control-strategy-for-a-solar-photovoltaic-power-system/c-b-sree-hara-vamsi
Enhancement of On-grid PV System under Irradiance and Temperature Variations ...IJECEIAES
Solar Energy is one of the key solutions to future electrical power generation. Photovoltaic Plants (PV) are fast growing to satisfy electrical power demand. Different maximum power point tracking techniques (MPPT) are used to maximize PV systems generated power. In this paper, on grid PV system model in MATLAB SIMULINK is tested under sudden irradiance and cell temperature variations. Incremental Conductance MPPT is used to maximize generated power from the PV system with the help of new adaptive controller to withstand these heavy disturbances. The new adaptive controller is tuned for optimal operation using two different optimization techniques (Invasive weed and Harmony search).Optimization results for the two techniques are compared. .A robustness test is made to check system stability to withstand different random irradiance and cell temperature patterns without failure to track the maximum power point. Finally, a brief comparison is made with a previous literature and the new adaptive controller gives better results.
Intelligent controller based power quality improvement of microgrid integrati...IJECEIAES
Now a day the power demand has a major problem for developing countries due to the growth of population, industries, IT companies and other needs. In this present situation the fossil fuel-based power generation alone does not support the consumer needs, poor power quality due to nonlinear function and very harmful for environment. The main objective of this paper is improving the power quality of grid connected photovoltaic power system through a new cascade H-bridge multilevel inverter. The proposed research work has been modelled and controlled by ANFIS intelligence in MATLAB simulation environment. The simulation results are analysed under various operating conditions for improve the performance of proposed system. Finally, the proposed system THD value of simulation results is compared with IEEE 1547 standard for prove the effectiveness of proposed research work.
Fuzzy Sliding Mode Control for Photovoltaic SystemIJPEDS-IAES
In this study, a fuzzy sliding mode control (FSMC) based maximum power point tracking strategy has been applied for photovoltaic (PV) system. The key idea of the proposed technique is to combine the performances of the fuzzy logic and the sliding mode control in order to improve the generated power for a given set of climatic conditions. Different from traditional sliding mode control, the developed FSMC integrates two parts. The first part uses a fuzzy logic controller with two inputs and 25 rules as an equivalent controller while the second part is designed for an online adjusting of the switching controller’s gain using a fuzzy tuner with one input and one output. Simulation results showed the effectiveness of the proposed approach achieving maximum power point. The fuzzy sliding mode (FSM) controller takes less time to track the maximum power point, reduced the oscillation around the operating point and also removed the chattering phenomena that could lead to decrease the efficiency of the photovoltaic system.
ENERGY MANAGEMENT SYSTEM FOR CRITICAL LOADS USING POWER ELECTRONICSrenukasningadally
The work aims at an Energy Management System (EMS) for Critical loads using Power Electronics. Here hybrid power sources (Grid and Solar cells) with battery have been used to supply the power to the critical loads at all times, suppose an end user increases his critical loads or non-critical loads this EMS system helps to maintain continuous power supply to these loads. Solar or Photovoltaic cells have been used for storing energy through battery and these batteries will discharge the stored energy at two conditions, one is when grid is shut down for short duration or for a long duration and another one is when there sudden increase in load by users
SALIENT FEATURES OF GRID-CONNECTED PHOTOVOLTAIC SYSTEM AND ITS IMPACT ON POWE...Editor IJMTER
Solar energy is available to the world for free of cost from millions of years and it is a
basic energy source to the mankind. It is also one of largest energy source to the mankind. PV
systems are a relative new technology. The operational experience with PV systems itself is at an
acceptable high level and today’s installed PV systems are of a good quality and are able to operate
without any problems for many years. The price level of the PV modules and the Balance of System
costs (inverter included) have decreased significantly. This energy is available all around the world
in large quantity. When this energy is collected by the solar PV cells it is in the small power with the
D.C. supply, which is not compatible with the existing grid in the world. There is an inverter and the
converter stage comes before this energy can used. Grid interactive PV systems can vary
substantially in size.
Performance Comparison of PID and Fuzzy Controllers in Distributed MPPTIJPEDS-IAES
With an increase of Green Technology applications, Photovoltaic have
emerged as the most appropriate solution for electricity generation purposes.
However, due to variable temperature and irradiance, under the partial or
shaded conditions Maximum Power Point Tracking is needed to determine
highest efficiency of the system. The paper describes dynamic modeling and
control of variable temperature and irradiance on solar panel in SIMULINKMATLAB
environment. The implementation of Buck Converter is used for
power switching and impedance matching on connecting the panel to the
load. The effectiveness of the model, with enhanced efficiency through
voltage stabilization, is performed using Proportional-Integral-Derivative and
Fuzzy-Logic-Controllers. A comparative study is made for PID and FLC on
the basis of outputs to deal with online set point variations. FLC gives closer
results to Standard Test Conditions when compared with PID. The Fuzzy
system developed, using tested membership functions serve as a platform for
sustainable standalone and grid-based applications using distributed MPPT.
This paper addresses the problem of controlling three-phase grid connected PV system involving a PV arrays, a voltage source inverter, a grid filter and an electric grid. This paper presents three main control objectives: i) ensuring the Maximum power point tracking (MPPT) in the side of PV panels, ii) guaranteeing a power factor unit in the side of the grid, iii) and ensuring the asymptotic stability of the closed loop system. Interestingly, the present study features the achievement of the above energetic goal without resorting to sensors of currents of the grid. To this end, an output-feedback control strategy combining a state observer and a nonlinear control laws is developed. The proposed output-feedback control strategy is backed by a formal analysis showing that all control objectives are actually achieved.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
The purpose of this article is to extract the maximum power point at which the photovoltaic system can operate optimally. The system considered is simulated under different irradiations (between 200 W/m2 and 1000 W/m2), it mainly includes the established models of solar PV and MPPT module, a DC/DC boost converter and a DC/AC converter. The most common MPPT techniques that will be studied are: "Perturbation and Observation" (P&O) method, "Incremental Conductance" (INC) method, and "Fuzzy Logic" (FL) control. Simulation results obtained using MATLAB/Simulink are analyzed and compared to evaluate the performance of each of the three techniques.
Design of Hybrid Solar Wind Energy System in a Microgrid with MPPT Techniques IJECEIAES
DC Microgrid is one feasible and effective solution to integrate renewable energy sources as well as to supply electricity. This paper proposes a DC microgrid with enhanced Maximum Power Point Tracking (MPPT) techniques for wind and solar energy systems. In this paper, the PV system power generation is enhanced by introducing a two-model MPPT technique that combines incremental conductance and constant voltage MPPT algorithms. Also, for the Wind Energy Conversion System (WECS) with pitch angle controlling technique, an Optimal Power Control MPPT technique is added. The Space Vector Pulse Width Modulation technique is introduced on grid side converter to improve the supply to the grid. The performance of proposed system is analyzed and the efficiency obtained with these methods is enhanced as compared with the previous methods.
Harmonic assessment on two photovoltaic inverter modes and mathematical model...IJECEIAES
Power quality is a crucial aspect of designing a large-scale photovoltaic power plant, particularly regarding harmonics caused by inverter switching. This research aimed to analyze harmonics in a system using electrical transient analyzer program (ETAP) Power Station 20.5.0 to uncover the effect of irradiance on the inverters’ power quality running at 85% and 100% power factors. We analyzed both voltage and current total harmonic distortion (THDi and THDv) from the simulation and compared them with the mathematical model. Moreover, we analyzed the effect of changes in irradiance level on harmonics and reactive power penetration, which influenced power losses in transformers and cables. Inverters at 85% power factor experienced an increase in THDi, whereas those at 100% power factor decreased. Inverters with 85% power factor experienced more frequent switching, causing more prominent distortion. The magnitude of THDv increased proportionally with the rise of irradiance level. Inverters at 85% had a higher THDv value because of the excessive reactive power compensation when irradiance rose. Irradiance level had an inverse relationship with system losses since high irradiance levels led to lower losses as less power was required through transmission lines and transformers. Moreover, losses at 85% power factor were higher since the high harmonics caused additional losses.
Fuzzy logic control of hybrid systems including renewable energy in microgrids IJECEIAES
With a growing demand for more energy from subscribers, a traditional electric grid is unable to meet new challenges, in the remote areas remains the extension of the conventional electric network very hard to do make prohibitively expensive. Therefore, a new advanced generation of traditional electrical is inevitable and indispensable to move toward an effective, economical, green, clean and self-correcting power system. The most well-known term used to define this next generation power system is micro grid (MG) based on renewable energy sources (RES). Since, the energy produced by RES are not constant at all times, a wide range of energy control techniques must be involved to provide a reliable power to consumers. To solve this problem in this paper we present a fuzzy logic control of isolated hybrid systems (HRES) including renewable energy in micro-grids to maintain a stability in voltage and frequency output especially in the standalone application. The considered HRES combine a wind turbine (WT) and photovoltaic (PV) panels as primary energy sources and an energy storage system (ESS) based on battery as a backup solution. Simulation results obtained from MATLAB/Simulink environment demonstrate the effectiveness of the proposed algorithm in decreasing the electricity bill of customer.
Performance analysis of grid-tied photovoltaic system under varying weather c...IJECEIAES
Model and simulation of the impact of the distribution grid-tied photovoltaic (PV) system feeding a variable load with its control system have been investigated in this study. Incremental Conductance (IncCond) algorithm based on maximum power point tracking (MPPT) was implemented for the PV system to extract maximum power under different weather conditions when solar irradiation varies between 250 W/m 2 and 1000 W/m 2 . The proposed system is modelled and simulated with MATLAB/Simulink tools. Under different weather conditions, the dynamic performance of the PV system is evaluated. The results obtained show the efficacy of the proposed MPPT method in response to rapid daytime weather variations. The results also show that the surplus power generated is injected into the grid when the injected power from the PV system is higher than the load demand; otherwise, the grid supplies the load.
This paper deals with an advanced design for a pump powered by solar energyto supply agricultural lands with water and also the maximum power point is used to extract the maximum value of the energy available inside the solar panels and comparing between techniques MPPT such as Incremental conductance, perturb & observe, fractional short current circuit, and fractional open voltage circuit to find the best technique among these. The solar system is designed with main parts: photovoltaic (PV) panel, direct current/direct current (DC/DC) converter, inverter, filter, and in addition, the battery is used to save energy in the event that there is an increased demand for energy and not to provide solar radiation, as well as saving energy in the case of generation more than demand. This work was done using the matrix laboratory (MATLAB) simulink program.
This work includes the establishment of a Photovoltaic system connected to the grid by means of an inverter. The fundamental goal of the work is to incorporate an advanced active power flow management scheme in order to adopt load at any weather condition along with the advantage of maximum active power flow and zero harmonics from PV inverter to the grid. The outcome of analysis and control design of grid connected PV inverter using a Proportional-Integral (PI) control technique is based on synchronous dq rotating reference frame so as to achieve maximum output voltage and record the active power. It has been observed that the model provides a better rate of stability as compared to the existing topology.
GA Based Controller for Autonomous Wind-DG Micro gridIOSRJEEE
A single renewable source of energy when integrated with other sources of energy it is termed as hybrid system. In this paper an active power control strategy has been developed such that when the wind alone is not able to meet the energy demand, without compromising the frequency a transition occurs to wind diesel mode so that the energy demand is met. This work proposes the coordination of WDG(Wind DG), VSC’s are used for two purposes one is frequency control and another is voltage control. PMBLDC generator is used as a wind power generator and the Incremental conductance method is used as MPPT along with boost converter. This output is stored into battery system (BS) and surplus is supplied to the consumer loads. Back propagation feed forward (BPFF) control scheme is used for VF control of VSC. This controller provides harmonics elimination, load leveling and reactive power compensation and also regulates the voltage at PCC. Genetic algorithm is used for the purpose of tuning PI controller of BPFF. The performance and the analysis is done in a user friendly MATLAB/Simulink environment.
Similar to Electric Vehicle as an Energy Storage for Grid Connected Solar Power System (20)
42 30 nA Comparative Study of Power Semiconductor Devices for Industrial PWM ...IAES-IJPEDS
The growing demand of energy translates into efficiency requirements of
energy conversion systems and electric drives. Both these systems are based
on Pulse Width Modulation (PWM) Inverter. In this paper we firstly present
the state of art of the main types of semiconductors devices for Industrial
PWM Inverter. In particular we examine the last generations of Silicon
Carbide (SiC) MOSFETs and Insulated Gate Bipolar Transistors (IGBTs)
and we present a comparison between these devices, obtained by SPICE
simulations, both for static characteristics at different temperatures and for
dynamic ones at different gate resistance, in order to identify the one which
makes the PWM inverter more efficient.
Modeling and State Feedback Controller Design of Tubular Linear Permanent Mag...IAES-IJPEDS
In this paper a state feedback controller for tubular linear permanent magnet
synchronous motor (TLPMSM) containing two gas springs, is presented.
The proposed TLPMSM controller is used to control reciprocating motions
of TLPMSM. The analytical plant model of TLPMSM is a multi-input
multi-output (MIMO) system which is decoupled to some sub single-input
single-output (SISO) systems, then, the sub SISO systems are converted to
sub-state space models. Indeed, the TLPMSM state space model is decoupled
to some sub-state spaces, and then, the gains of state feedback are calculated
by linear quadratic regulation (LQR) method for each sub-state space
separately. The controller decreases the distortions of the waveforms.
The simulation results indicate the validity of the controller.
Analysis of Harmonics and Ripple Current in Multi-Module Converters with Incr...IAES-IJPEDS
Controlled rectifiers are considered as the most important hardware part in
the field of HVDC systems in transmission lines and can be used for a
number of power electronics based system operation, control and utility
applications. In this paper, a brief design of a 12-pulse, 24-pulse, 36-pulse
and a 48-pulse converter connected to the grid is presented along with the
harmonic and ripple current analysis with its comparison statistics and thus
providing a justification for the suitable ones. The performance of the
12, 24, 36 and 48-pulse converters are compared for their effectiveness in
both quantitatively as well as qualitatively. Further, comparison of the
48-pulse converter on its THD and current ripple which is connected towards
the grid with simple pulse width modulation technique is also proposed. It
combines all features of the low switching concepts and DC current reinjection
techniques. Some basic topological explanation of the controlled
rectifiers and simulation results using MATLAB are also presented in this
paper in order to justify the harmonic analysis. The simulation results along
with the quantitative results shows the effectiveness of the proposed scheme
for the cancelation or the elimination of the harmonics result in maximum
harmonic mitigation, for high power utility applications, the 48-pulse
converter is most fitting to improve the conversion efficiency, low di/dt
and dv/dt and active and reactive power controllability.
Comparative Study of Various Adjustable Speed Drives during Voltage SagIAES-IJPEDS
This Paper compares the sensitivity of various adjustable speed drives to
voltage sag for the process control applications. Three phase voltage sag of
type B caused due to SLG fault is considered and four topologies of ASD’s
are compared in this paper. The comparison is done especially in speed,
voltage, current and torque of the ASDs. Diode rectifier without z source
inverter, diode rectifier with z source inverter, single phase two leg Vienna
rectifier and single phase neutral linked Vienna with z source inverter are
compared and the best one is highlighted. The circuits of various ASD’s are
simulated using Matlab /Simulink.
Modified Distribution Transformer for Enhancing Power Quality in Distribution...IAES-IJPEDS
The percentage of non-linear loads in the power distribution sector is increasing
day by day. Harmonics injected by these non-linear loads circulate in the delta
windings of the conventional distribution transformer thereby increasing the
temperature and losses. This reduces the efficiency and life of the transformers.
In a modified distribution transformer configuration proposed recently, called
star-star-delta_utilized configuration (YYD_utilized), the harmonics circulating
in the delta winding was utilized and the drainage power thus recovered was
used to power auxiliary loads. This paper presents the experimental studies
conducted on YYD_utilized distribution transformer. When compared to
conventional star-star, delta-star and star-star-delta transformers, the new
configuration of YYD_utilized transformer has shown considerable
improvement in transformer efficiency. The results obtained show that when
the power from the circulating harmonics is recovered and utilized, it not only
improves transformer efficiency but also improves the power factor
and reduces the harmonic distortions at the primary side of the transformer.
The results obtained also suggest the existence of maximum power point or an
optimum loading for the recovered harmonic power.
Modelling of Virtual Synchronous Converter for Grid-Inverter Synchronization ...IAES-IJPEDS
In this paper, virtual synchronous converter (VSCon) is been developed
which mimic the behavior of synchronous generator as in order to have fast
synchronization between the inverter with the grid. This synchronization is
important before can sent the power among inverter-grid connection. This
technique can also been applied at the distributed generated sources when are
connected to the local microgrids. Here, the frequency and voltage
synchronization also can be controlled at the same time some improvement
on synchronous generator mathematical model that is suitable to be
implemented into the inverter control. The whole unit of VSCon is operated
and simulated in Matlab/Simulink in order to observe all consequences
during synchronizing the voltage, frequency and phase-angle. It has been
verified by the simulation circuit where, the power converter can be
synchronized with the microrids without using a PLL unit for self
synchronization. This VSCon technique has proven that, by applying the
concept of the synchronous generator model in inverter control, it can cause
the inverter to behave as generator system, which does not required any
phase information from the grid in order to be synchronized.
Enhanced Crowbar Protection for Fault Ride through Capability of Wind Generat...IAES-IJPEDS
Due to increasing demand in power, the integration of renewable sources like
wind generation into power system is gaining much importance nowadays.
The heavy penetration of wind power into the power system leads to many
integration issues mainly due to the intermittent nature of the wind and the
desirability for variable speed operation of the generators. As the wind power
generation depends on the wind speed, its integration into the grid has
noticeable influence on the system stability and becomes an important issue
especially when a fault occurs on the grid. The protective disconnection of a
large amount of wind power during a fault will be an unacceptable
consequence and threatens the power system stability. With the increasing
use of wind turbines employing Doubly Fed Induction Generator (DFIG)
technology, it becomes a necessity to investigate their behavior during grid
faults and support them with fault ride through capability. This paper
presents the modeling and simulation of a doubly fed induction generator
according to grid code compatibility driven by a wind turbine connected to
the grid. This paper analyses the voltage sag due to a three-phase fault in the
wind connected grid. A control strategy including a crowbar circuit has been
developed in MATLAB/SIMULINK to bypass the rotor over currents during
grid fault to enhance the fault ride through capability and to maintain system
stability. Simulation results show the effectiveness of the proposed control
strategies in DFIG based grid connected wind turbine system.
An Improved of Multiple Harmonic Sources Identification in Distribution Syste...IAES-IJPEDS
This paper introduces an improved of multiple harmonic sources
identification that been produced by inverter loads in power system using
time-frequency distribution (TFD) analysis which is spectrogram.
The spectrogram is a very applicable method to represent signals in
time-frequency representation (TFR) and the main advantages
of spectrogram are the accuracy, speed of the algorithm and use low memory
size such that it can be computed rapidly. The identification of multiple
harmonic sources is based on the significant relationship of spectral
impedances which are the fundamental impedance (Z1) and harmonic
impedance (Zh) that extracted from TFR. To verify the accuracy of the
proposed method, MATLAB simulations carried out several unique cases
with different harmonic producing loads on IEEE 4-bus test feeder cases. It is
proven that the proposed method is superior with 100% correct identification
of multiple harmonic sources. It is envisioned that the method is very
accurate, fast and cost efficient to localize harmonic sources in distribution
system.
Performance and Energy Saving Analysis of Grid Connected Photovoltaic in West...IAES-IJPEDS
The paper presents performance and energy saving analysis of 1.25 kWp grid
connected photovoltaic system under difference weather condition in West
Sumatera. The measured data were performed during weather data that often
occur in West Sumatra i.e. sunny, overcast, raining and cloudy.
The synchronizing process successfully done even bad weather conditions
when sunlight was low automatically. Photovoltaic in average start
producing power from 7:00 AM to 6:00 PM for normal or clear sky, however
under overcast, raining and cloudy weather, the PV power decreased and
disconnected earlier before sunset. During intermittent raining, overcast and
cloud covered the PV power output show an irregular profile. The PV energy
saving performed for three residential connection cases: 1300 VA, 900 VA
with subsidized and 900 VA without subsidized. The solar PV installation
have more benefits and energy saving for 1300 VA, 900 VA without
subsidized with payback period around 8.5 years. However, the 900 VA with
subsidized take longer 20.8 years, but still in PV lifespan 25 years. In the
future, household subsidies may be reduced or eliminated, the solar energy
will be viable alternative of energy resources when it can produce electricity
at a cost equivalent to utility grid PLN rate.
An Improved Constant Voltage Based MPPT Technique for PMDC MotorIAES-IJPEDS
Stand-alone photovoltaic (SAPV) systems are being used in remote areas
and are being seen as one of the promising solution in this regard. The SAPV
system as presented in the paper consists of solar PV panel, a DC-DC
converter, a controller and a PMDC motor. The current-voltage and powervoltage
characteristics being nonlinear, the SAPV system require maximum
power point techniques (MPPT) control techniques to extract maximum
power available from the PV cell. A voltage based MPPT technique which is
capable of tracking MPP has been selected because of numerous advantages
it offers such as: simple and low cost of implementation. The limitation of
constant voltage method is that its efficiency is low as the PV panel has to be
disconnected from the load for measurement of the open circuit voltage
(Voc). In the presented paper, the authors have removed this limitation by
using a pilot PV panel for measurement of Voc. A proportional-integrator (PI)
based controller is used in implementation of constant voltage MPP
technique and the modeling is done in MATLAB®/SIMULINK simulation
environment. The simulation results are presented and discussed in the paper,
the results shows that the efficiency of the system has increased.
A Discrete PLL Based Load Frequency Control of FLC-Based PV-Wind Hybrid Power...IAES-IJPEDS
The sun and wind-based generation are considered to besource of green
power generation which can mitigate the power demand issues. As solar and
wind power advancements are entrenched and the infiltration of these
Renewable Energy Sources (RES) into to network is expanding dynamically.
So, as to outline a legitimate control and to harness power from RES the
learning of natural conditions for a specific area is fundamental. Fuzzy Logic
Controller (FLC) based Maximum Power Point Tracking (MPPT) controlled
boost converter are utilized for viable operation and to keep DC voltage
steady at desired level. The control scheme of the inverter is intended to keep
the load voltage and frequency of the AC supply at aconstant level regardless
of progress in natural conditions and burden. A Simulink model of the
proposed Hybrid system with the MPPT controlled Boost converters
and Voltage regulated Inverter for stand-alone application is developed in
MATLAB R2015a, Version 8.5.0. The ongoing information of Wind Speed
and Solar Irradiation levels are recorded at BITS-Pilani, Hyderabad Campus
the performance of the voltage regulated inverter under constant and varying
linearAC load is analyzed. The investigation shows that the magnitude of
load voltage and frequency of the load voltage is maintained at desired level
by the proposed inverter control logic.
An Adaptive Virtual Impedance Based Droop Control Scheme for Parallel Inverte...IAES-IJPEDS
This paper presents an adaptive virtual impedance based droop control
scheme for parallel inverter operation in low voltage microgrid. Because it is
essential to achieve power sharing between inverters in microgrid, various
droop control schemes have been proposed. In practice, the line impedance
between inverters and the point of common coupling (PCC) in microgrid are
not always equal. This imbalance in line impedance often results in a reactive
power mismatch among inverters. This problem has been solved by
introducing a virtual impedance loop in the conventional droop control
scheme. However, the reactive power sharing performance of this method is
still deteriorated when the line impedances change during operation. To
overcome such a problem, a new control scheme that is based on a virtual
impedance loop and an impedance estimation scheme is proposed.
To monitor the changes in line impedances, the impedance estimator is
implemented by using the output voltages and currents of inverters as well as
the voltages at the PCC. To compensate for the reactive power mismatch due
to the line impedance changes, the estimated line impedance is fed to the
virtual impedance loop in which it adjusts the virtual impedance value.
Comparative simulation results with the conventional ones verify the
effectiveness of the proposed adaptive virtual impedance based droop control
scheme.
Open-Switch Fault-Tolerant Control of Power Converters in a Grid-Connected Ph...IAES-IJPEDS
This paper presents the study of an open switch fault tolerant control of a
grid-connected photovoltaic system. The studied system is based on the
classical DC-DC boost converter and a bidirectional 6-pulse DC-AC
converter. The objective is to provide an open-switch fault detection method
and fault-tolerant control for both of boost converter and grid-side converter
(GSC) in a grid-connected photovoltaic system. A fast fault detection method
and a reliable fault-tolerant topology are required to ensure continuity of
service, and achieve a faster corrective maintenance. In this work, the mean
value of the error voltages is used as fault indicator for the GSC, while, for
the boost converter the inductor current form is used as fault indicator. The
fault-tolerant topology was achieved by adding one redundant switch to the
boost converter, and by adding one redundant leg to the GSC. The results of
the fault tolerant control are presented and discussed to validate the proposed
approach under different scenarios and different solar irradiances.
Photovoltaic System with SEPIC Converter Controlled by the Fuzzy LogicIAES-IJPEDS
In this work, a fuzzy logic controller is used to control the output voltage of a
photovoltaic system with a DC-DC converter; type Single Ended Primary
Inductor Converter (SEPIC). The system is designed for 210 W solar
photovoltaic (SCHOTT 210) panel and to feed an average demand of 78 W.
This system includes solar panels, SEPIC converter and fuzzy logic
controller. The SEPIC converter provides a constant DC bus voltage and its
duty cycle controlled by the fuzzy logic controller which is needed to
improve PV panel’s utilization efficiency. A fuzzy logic controller (FLC) is
also used to generate the PWM signal for the SEPIC converter.
An Approach to Voltage Quality Enhancement by Introduction of CWVM for Distri...IAES-IJPEDS
This paper presented with problems related with voltage flicker in power
system networks. Several international standard issued to control the voltage
flicker are briefly described and some important methods to analyse
electrical circuits with sinusoidal and non-sinusoidal waveforms are
introduced and evaluated. One of these methods-Cockcroft Walton Voltage
Multiplier (CWVM) has been used to increase the voltage of a filter, which is
also described in this paper as a practical application. The filter can
compensate for harmonic currents, power factor, and unbalance voltage.The
simulation results using Multisimare presented, showing that good dynamic
and steady-state response can be achieved with this approach.
Electric Power Converter with a Wide Input Voltage RangeIAES-IJPEDS
The electric power converter for downhole telemetry systems of oil-well
pumps include a downhole block connected to the pump that contains
electronic circuits required for the operation of the motor pump sensors
and transmission of data about their condition to the surface are described.
A few methods of electric power conversion for this purpose are considered.
The circuit contained two steps of voltage converting are proposed.
The electrical scheme of this method is considered in the article. Proposed
decisions are simulated and verified experimentally. The input high supply
voltage range (200-4200 V) without loss of efficiency (even temporary) was
obtained. The results of simulation and experimental studies have shown
very close results.
Design and Implementation of Real Time Charging Optimization for Hybrid Elect...IAES-IJPEDS
Electric vehicle (EV) has gained incredible interest from the past two decade
as one of the hopeful greenhouse gasses solution. The number of Electric
Vehicle (EV) is increasing around the world; hence that making EVs user
friendly becomes more important. The main challenge in usage of EV is the
charging time required for the batteries used in EV. As a consequence, this
subject matter has been researched in many credentials where a wide range
of solutions have been proposed. However those solutions are in nature due
to the complex hardware structure. To provide an unswerving journey
an Android application based charging optimization is proposed.
This application is aimed at giving relevant information about the EV’s
battery state of charge (SOC), accurate location of the EV, booking of the
charging slots using token system and route planner. At emergency
situations, an alternative service is provided by mobile charging stations.
Route planner indicates the temperature by which prediction of reaching the
destination can be done. In addition to that nearest places such as parks,
motels are indicated. The estimated time and distance between the electric
vehicle and the charging station is calculated by the charging station server
according to which the parking lot is allocated. Vehicle to charging station
communication is established for the time estimation of charging. This will
help the EV users to know about charge status and charging station, which
support fast charging method and availability of the station on the go
and also when to charge their EV. The Arduino UNO board has been used
for the hardware part. The hardware results are confirming the conceptual of
the proposed work.
Performance Analysis of Photovoltaic Induction Motor Drive for Agriculture Pu...IAES-IJPEDS
This paper presents water pumping system using renewable source (solar)
without the use of chemical storage batteries. In this converter-inverter
circuit is used to drive Induction motor. The Converter used here is Two
Inductor boost converter (TIBC), which consists of a resonant tank, voltage
doubler rectifier and a snubber circuit. TIBC is designed to drive the three
phase induction motor from PV energy. TIBC converter is also known as
current fed multi resonant converter having high voltage gain and low input
current ripple. Converter switches are controlled through hysteresis controller
and ZCS resonant topologies. Solar PV power fluctuates according to
irradiation level of sunlight and hence tracking of maximum power at all
time is mandatory. SPWM control with third harmonic injection is used to
trigger the IGBT’s in the inverter. The development is oriented to achieve a
more efficient, reliable, maintenance free and cheaper solution than the
standard ones, that uses DC motors or low voltage synchronous motors.
The proposed method is verified with MATLAB/SIMULINK and the system
simulation confirms the performance of the proposed system.
Comparison of Sine and Space Vector Modulated Embedded Z-Source Inverter fed ...IAES-IJPEDS
This paper deals with performance of photovoltaic powered Embedded
Z-Source Inverter (EZSI) fed Induction motor drive. The DC output from the
PV-Panel is boosted and converted into AC using Embedded Z-Source
Inverter. EZSI system based on the concept of Z-Source Inverter (ZSI),
which provides single stage power conversion. The EZSI also produce same
voltage gain as that of the ZSI based system. In EZSI the DC source is
embedded within the X-shaped LC impedance network, due to this EZSI has
the added advantage of inherent source filtering capability, this can be
achieved without any extra passive filter. EZSI can produce the AC output
voltage which is greater than the DC link voltage. EZSI system also provides
ride-through capability under voltage sags. In this paper the performance of
space vector modulated EZSI fed Induction Motor Drive is compared with
sinusoidal PWM controlled EZSI fed Drive system. The PV powered EZSI
fed three phase Induction Motor System is designed, modeled and simulated
using MAT LAB-SIMULINK and the corresponding results are presented.
This drive system has advantages like voltage boosting ability and reduced
harmonic content.
Single-Phase Multilevel Inverter with Simpler Basic Unit Cells for Photovolta...IAES-IJPEDS
This paper presents a single-phase multilevel inverter (MLI) with simpler
basic unit cells. The proposed MLI is able to operate in two modes, i.e.
charge mode to charge the batteries, and inverter mode to supply AC power
to load, and therefore, it is inherently suitable for photovoltaic (PV) power
generation applications. The proposed MLI requires lower number of power
MOSFETs and gate driver units, which will translate into higher cost saving
and better system reliability. The power MOSFETs in the basic unit cells
and H-bridge module are switched at near fundamental frequency, i.e. 100
Hz and 50 Hz, respectively, resulting in lower switching losses. For low total
harmonic distortion (THD) operation, a deep scanning method is employed
to calculate the switching angles of the MLI. The lowest THD obtained is
8.91% at modulation index of 0.82. The performance of the proposed MLI
(9-level) has been simulated and evaluated experimentally. The simulation
and experimental results are in good agreement and this confirms that the
proposed MLI is able to produce an AC output voltage with low THD.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Quality defects in TMT Bars, Possible causes and Potential Solutions.PrashantGoswami42
Maintaining high-quality standards in the production of TMT bars is crucial for ensuring structural integrity in construction. Addressing common defects through careful monitoring, standardized processes, and advanced technology can significantly improve the quality of TMT bars. Continuous training and adherence to quality control measures will also play a pivotal role in minimizing these defects.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
2. ISSN: 2088-8694
IJPEDS Vol. 6, No. 3, September 2015 : 567 – 575
568
an external energy storage [6] can be extended to a solar powered system also. In the near future the rising
penetration of PV system may also lead to important impacts on power distribution systems, particularly due
to the intermittent nature of its output caused by cloud cover [7]. Therefore, a coordinated use of solar
powered system with EVs will be a possible solution which can help to maintain a flat power profile to the
grid.
EVs can be coordinated with PV systems in many ways. For example, a dc-dc converter inserted
between an EV and the dc bus voltage of a PV system can improve grid integration of PV systems by
reducing the ramp rate of the PV inverter output power [8] [9]. To reduce the fluctuations in the grid, only
slowly changing power can be exported by the use of a high pass filter in the network, which directs rapid
power fluctuations to the EV battery [10]. Not only that, to regulate the energy imbalance in the system, the
day time solar generated power can effectively be converted into night time consumption using the vehicle to
grid and grid to vehicle concept [11]. Also as more and more PV generation is pumped into the existing
power system, the need for an energy storage which is cost effective is emphasized [12, 13, 14].
However, in order to generate more confidence on this technology, the system has to be exposed to
realistic field data. This is the most important objective of this paper, where, a grid connected combined PV
and EV system is thoroughly modeled and studied by incorporating the real field data in PSCAD/EMTDC
environment. In order to verify the performance of the PV-EV combined microgrid, field data (solar
irradiance and temperature) obtained from Centre for Wind Energy Technology (CWET), Chennai,
Tamilnadu, India has been used. The results obtained shows that this Electric Vehicle technology in
coordination with the solar PV generating unit gives a smooth power output to the grid. This paper is
organized as follows: In section II, modeling and control of grid connected PV-EV combined system is
discussed. The simulation results are shown in Section III and conclusions are drawn in Section IV.
2. PROPOSED MODEL AND CONTROL OF GRID CONNECTED PV-EV COMBINED
MICROGRID
2.1. Modeling and Control of Grid Connected PV System
The pictorial representation of a grid connected PV system is represented in Figure 1. The input to
the PV module is nothing but the solar irradiance and the temperature. The DC-DC converter is used to boost
the output of the PV module. The firing pulse of the DC-DC converter is generated through the MPPT
control logic. The output of the converter is connected to the grid through a three phase current controlled
PWM inverter.
2.1.1. Modelling of the Solar Farm
In this paper, a 100 kW solar farm is modeled in PSCAD/EMTDC platform. The parameter values
of all the passive components are obtained from the Matlab demo model of a 100 kW solar PV system. Ten
numbers of modules are connected in series and eight numbers of modules are connected in parallel. There
are 216 cells connected in series per module and eight cells in each string per module in series. The series
resistance per cell is 0.02 ohm and the shunt resistance is 1000ohm. The output voltage of the solar panel is
obtained across a capacitor (C in Figure 1).
Figure 1. Schematic diagram of the grid connected PV system
Solar Panel
Irradiation
Temperature
C
Vpv C1
L
Grid
3. IJPEDS ISSN: 2088-8694
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System(E. Sheeba Percis)
569
2.1.2. Modelling of the Boost Converter
It is also very important to extract the maximum possible power from the panel using Maximum
Power Point Tracking (MPPT) algorithm. The algorithm is embedded inside the control of the boost
converter. The implementation of MPPT based boost converter control in this paper is presented in Figure 2.
Fig. 2 shows that the output current (Ipv) and output voltage (Vpv) of the PV module are passed through first
order low pass filters. The MPPT block uses the Incremental Conductance Algorithm for tracking the
required point. The algorithm is based on the fact that the slope of the PV array power curve is zero at the
Maximum Power Point (MPP), positive on the left of the MPP, and negative on the right. The MPP can thus
be tracked by comparing the instantaneous conductance (I/V) to the incremental conductance (ΔI/ΔV).
The output of the MPPT block is the MPP voltage (Vmpp). This is the voltage at which the PV
module has to operate to extract maximum power. The algorithm decrements or increments Vmpp to track the
maximum power point when operating under varying climatic conditions and passing clouds. This voltage
(Vmpp) is then compared with the measured PV panel output voltage (Vpv) and is fed as the input to PI
controller. The output of the PI controller is used to generate the switching pulses for the boost converter.
Figure 2. MPPT and the control of boost converter
2.1.3. Control of the Inverter
The output of the DC-DC converter is connected to the inverter, which converts it into AC and then
connects it to the utility grid. The inverter is a two-level voltage source converter (VSC) using IGBT
switches along with anti-parallel diodes as shown in Figure 1. Current controlled PWM technique is used to
generate the switching order for the IGBTs. In order to explain the control of the grid-connected VSC, a
simplified diagram is shown in Figure 3. The complex phasor representation of Figure 3 is again shown in
Figure 4.
Figure 3. Schematic diagram of a grid connected
VSC
Figure 4. Complex phasor representation of grid
connected VSC
From Figure 4, it appears that
s
s
ss
v
i
ie
dt
d
LR (1)
MPPT
Control
Vpv
Ipv
Vpv_filtered
Ipv_filtered
PV
Output
+
‐
PI
Controller
Comparator
Vmpp
Switching
orderX
s
e
s
i
s
v
R L
4. ISSN: 2088-8694
IJPEDS Vol. 6, No. 3, September 2015 : 567 – 575
570
Here,
s
e is the converter voltage,
s
v is the grid voltage and
s
i is the current flowing from converter to the
grid. All these variables are represented in stationary reference frame. Converting them into synchronous (d-
q) reference frame yields
v
i
iie
v
i
iie
v
i
ie s
s
ss
)(
)}({
dt
d
jLR
dt
d
jeLeR
e
dt
d
LeRee
jj
jjjj
(2)
The PLL is used to generate the value of theta θ. This theta is used to turn on and off the IGBT’s which in
turn controls the flow of real and reactive power.
Putting qdqdqd jiijvvjee ive ,, and separating real and imaginary parts
(3)
Aligning the d-axis of the reference frame on the voltage space vector, we obtain
vdv 0qv (4)
With this new reference frame orientation we obtain complete decoupling of active and reactive power. The
power equations become
dd ivP qd ivQ (5)
Equation (3) now changes to
(6)
In equation (6), the terms and are the speed/frequency induced terms that gives raise to
the cross coupling between the two axes. These terms are considered as disturbances in the system and hence
eliminating them will yield better results. If we define our commanded converter d and q voltages as
*
de and
*
qe and commanded currents to be )(refdi and )(refqi , then with a PI type current controller along with cross-
coupling compensation, following equations hold
dqdrefd
i
pd vLiii
s
K
KLe
)( )(
*
; dqrefq
i
pq Liii
s
K
KLe
)( )(
*
(7)
Here, since di is directly proportional to active power (5), then it is reasonable to control the DC voltage by
controlling the di . Therefore, )(refdi can be generated as an output of the DC voltage controller.
)( *
)( dcdc
idc
pdcrefd vv
s
K
Ki
(8)
5. IJPEDS ISSN: 2088-8694
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System(E. Sheeba Percis)
571
The overall control of the inverter for the grid connected PV system is shown in Figure 5.
2.2. Modelling and Control of Grid Connected Electric Vehicle
The electric vehicle is modeled as a DC voltage source with a three-phase two-level inverter through
which it connects to the grid (Figure 6). The control of the electric vehicle inverter system is almost the same
as the PV inverter. The only difference between the two is that since it is connected to a constant DC voltage
source, the DC voltage control is not necessary. Instead, it can directly control the active power commanded
(
*
EVP ) from the electric vehicle. However, here the active power order comes from the coordinating
controller which controls the overall power injection (PV+EV) into the utility grid.
Figure 5. Overall control schematic of the grid connected PV inverter
2.3. Coordinated Control of the PV-EV Combined Microgrid
In order to smooth out the power fluctuations from the PV inverter and to make sure that the power
injection to the utility grid is absolutely constant, a coordinating controller is necessary. The desired power to
the utility grid is given as an input to the coordinating controller. It also tracks the output power from the PV
system. Then the difference between these two powers, which is the output of the coordinating controller, can
be used as the commanded power for the EV system. Mathematically,
**
EVPVutility PPP (10)
where, ∗
represents the desired power output of the utility grid, represents the output power from
the solar generating plant and ∗
represents the commanded power to the electric vehicle.
Figure 6. Schematic representation of grid connected EV
PLL
abcv
abc
to
dq
dv
qv v
)(refdi
refQ -1
)(refqi
abc
to
dq
abci
di
qi
PI‐
‐ PI
‐
ωL
+
+
ωL
dq
to
abc
*
abce
*
de
*
qe
PI‐
*
dcv
dcv
+
‐
Grid
Ia
Ib
Ic
6. ISSN: 2088-8694
IJPEDS Vol. 6, No. 3, September 2015 : 567 – 575
572
3. SIMULATION RESULTS AND DISCUSSION
3.1 Performance of the Solar PV System
In order to verify the performance of the PV-EV combined microgrid, field data obtained from
Centre for Wind Energy Technology (CWET), Chennai, Tamilnadu, India has been used in this paper. The
organization provides site data for both solar PV and wind systems. In this paper one minute data is taken
into consideration, as it is meaningful to interpolate the same. The inverters in the electric vehicle should be
very fast to mitigate power unbalance, but they are not supposed to work for a long time. Therefore if ten
minutes data is used then the interpolation will not be realistic. Hence the solar irradiance and temperature
data with one minute interval on 1st
January, 2013 at a site location in Chennai, Tamil Nadu is used. The site
description is shown in the below table 1.
Table 1. Site Description
Station Name/ID Chennai/1791
Latitude 12 ° 57'21.79'' N
Longitude 80°12'59.75'' E
Elevation / Altitude 1m amsl / 0 m agl
Site Address National Institute of Wind Energy, Chennai, Tamilnadu.
The data sheet specified the Sun height angle, Sun azimuth angle, Global horizontal irradiance
"W/m^2", Direct normal irradiance "W/m^2", Diffuse horizontal irradiance "W/m^2", Horizontal wind speed
(10m) "m/s", Wind direction, Air temperature "°C", Relative humidity "%", Barometric pressure "hPa",
Precipitation "mm", Dew point temperature "°C", Wet bulb temperature "°C".
All the simulations are carried out with a 100 minutes’ data set starting from 10:00 AM. However,
in PSCAD, it is quite time consuming to actually run a 100 minutes’ data set when the simulation time-step is
50 µs. Such a small time-step has to be used in order to achieve the high frequency switching of the power
electronic converters which are modeled in quite detail in this paper. In order to obtain a realistic solution to
this problem, the 100 minutes’ data set is used in the PSCAD model. All the simulation results are obtained
with respect to time (100 minutes) in the x-axis.
Figure 7 (a) shows, how the irradiance and temperature has varied during the time interval
mentioned before. Due to that variation, the output of the solar PV system changes, which is shown in Figure
7 (b). The output of the PV array varies within the range of 80 kW to 130 kW. This power is captured using
the MPPT algorithm discussed before.
Figure 7 (a) Solar irradiance and temperature
variation with time as per the field data
Figure 7 (b) Variation of PV array output power due
to the variation of irradiance and temperature
Now, in order to send this power to the utility grid, it is required to hold the DC link voltage of the
solar PV inverter to a constant value by the DC voltage controller. The performance of the DC voltage
controller in such a varying power scenario is therefore important for the correct operation of the solar PV
system. In Figure 8, the reference and the actual DC voltage of the DC link is shown. It is observed that even
in this varying power scenario, the DC link voltage is successfully maintained at the commanded value.
7. IJPEDS ISSN: 2088-8694
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System(E. Sheeba Percis)
573
Figure 8. Reference and actual DC voltage of the
inverter DC link
Figure 9. Reference and actual d-axis current of
the solar inverter
Another important component of the solar PV inverter is the current controller. The current
controller in the d-axis has to be fast enough to track the current reference generated by the DC voltage
controller. At the same time the current controller has to be able to limit the current in case of transient events
so that the converter valves does not experience high unwanted current beyond its rating. In Figure 9, the
tracking of the d-axis current controller is shown. Here Idord is the reference current and Id is the actual current
waveforms. From the reference and actual current, the successful operation of the current controller is
established.
3.2 Performance of the Electric Vehicle
In this case an electric vehicle is used in order to absorb the power variations caused due to the
variation in irradiation and temperature. In figure 7, these variations are simulated using the real time field
data obtained from Centre for Wind Energy Technology, Chennai, Tamilnadu, India. The Control circuit of
the electric vehicle tracks the Pord and the vehicle power follows the same satisfactorily. The vehicle power
varies in the range of +/- 30kW. The vehicle power tracks the reference power which is shown in figure 10.
In this model a constant dc source of 5kV is used as reference.
Figure 10 Reference and actual vehicle power
As mentioned earlier in section B, the control of the electric vehicle inverter system is similar to that
of the PV inverter. Since a constant DC source is used, DC voltage control is not required. Instead, it can
directly control the active power commanded (
*
EVP ) from the electric vehicle. However, here the active
power order comes from the coordinating controller which controls the overall power injection (PV+EV) into
the utility grid. Then, the reference current for the current controller is calculated directly from the following
equation
d
EV
EVrefd
v
P
i
*
_)(
Following the above equation, the reference current is tracked by the actual d-axis current of the
electric vehicle successfully.
8. ISSN: 2088-8694
IJPEDS Vol. 6, No. 3, September 2015 : 567 – 575
574
3.3 Performance of the PV-EV Combined Microgrid
Now, with an objective to obtain a flat power profile injected to the utility grid, a power reference of
100 kW is set in the coordinating controller. It means that, if the PV system produces more power than 100
kW, then the EV will absorb the excess power. Similarly, if the PV system produces less power than 100 kW,
the EV system will supply the deficit. Obviously, the EV system cannot supply or absorb power for
indefinitely long period. It will be determined by the available state of charge of the EV batteries which are
taking part in this V2G and G2V transactions. In this case, it was assumed that the EV system which
constitutes the PV-EV combined microgrid, is capable of supporting the PV system within a range of +/- 30
kW. Figure 11 shows that with such a simple implementation of a coordinating controller, the power fed into
the grid is maintained perfectly at the commanded value, which is 100 kW in this case. The solar power
fluctuations are completely absorbed by the EV system, which helps the combined system to maintain a flat
power profile.
Figure 11. Performance of the PV-EV combined microgrid
It is evident from the field data obtained that renewable energy sources like solar, wind etc increases
the demand for reserves and regulations in view of their intermittent nature. Asmore of these sources are
injected into the grid nowadays, the electric grid needs something to bridge the gap between altering demand
or supply and the response of the generally slow large generation units. This reserve/balancing capacity is is
termed as ‘ancillary services’. In [6, 11] the role of EV’s is specified and the number of EV’s to be deployed
in accordance to the load demand is reported but real field data has not been incorporated in these studies. In
[3] the modeling of the solar PV system is carried out but the intermittency has not been addressed. In the
present work the real field data of the solar irradiance and temperature has been used to validate the EV
technology and the results abtained clearly shows that the power output to the grid is stable.
4. CONCLUSIONS
In this paper, it is shown that a coordinated control is capable of maintaining a flat power profile
which is fed into the utility grid from a PV system by mitigating the intermittency with electric vehicles in a
PV-EV combined micrigrid. A PSCAD simulation, which uses field data for solar irradiance and
temperature, are carried out to verify this idea. The results shown in this paper are very promising to establish
the claim that electric vehicles can be used as an external energy storage to a solar PV unit in microgrid.
REFERENCES
[1] Joydeep Mitra, Niannian Cai, Mo-Yuen Chow, Sukumar Kamalasadan, Wenxin Liu, Wei Qiao, Sri Niwas Singh,
Anurag K. Srivastava, Sanjeev K. Srivastava, Ganesh K. Venayagamoorthy, Ziang Zhang. Intelligent Methods for
Smart Microgrids. Power & Energy society General Meeting. IEEE Conference. July 2011; 24-29.
9. IJPEDS ISSN: 2088-8694
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System(E. Sheeba Percis)
575
[2] Kodanda Ram R B P U S B, Venu Gopala Rao Mannam. Operation and Control of Grid Connected Hybrid AC/DC
Microgrids using RES. IJPEDS. October 2014; Vol 5 (No 2); 195-202.
[3] Mohamed Louzazni, El Hassan Aroudam, Hanane Yatimi. Modelling and Simulation of a Solar Power Source for a
Clean Energy without Pollution. August 2013; Vol 3 (No. 4); 568-576.
[4] Pinaki Mitra, Ganesh K. Venayagamoorthy. Intelligent Coordinated control of a Windfarm and Distributed Smart
Parks. Industry Applications Society Annual Meeting (IAS) IEEE. 2010.
[5] G. K. Venayagamoorthy and P. Mitra. SmartPark Shock Absorbers for Wind Farms. IEEE Transactions on Energy
Conversion. September 2011; Vol. 26 (Issue 3); 990 – 992.
[6] Zahedi, A. Electric Vehicle as distributed energy storage resource for future smart grid. Universities Power
Engineering Conference (AUPEC). Sept. 2012; 1 – 4.
[7] Aguero, J.R. Chongfuangprinya, P.; Shengnan Shao; Le Xu ; Jahanbakhsh, F.; Willis, H.L. Integration of Plug-in
Electric Vehicles and distributed energy resources on power distribution systems. Electric Vehicle Conference
(IEVC). March 2012; 1 – 7.
[8] Traube, J., Fenglong Lu, Maksimovic, D. Mossoba, J. Kromer, M.; Faill, P. Katz, S. Borowy, B. Nichols,
S. Casey, L. Mitigation of Solar Irradiance Intermittency in Photovoltaic Power Systems With Integrated Electric-
Vehicle Charging Functionality. IEEE Transactions on Power Electronics. June 2013; Vol 28 (Issue 6); 3058 –
3067.
[9] Foster, J. M., Trivino, G., Kuss, M., Karamanis, M.C. Plug-in-Electric Vehicle and voltage support for distributed
solar. Systems Journal IEEE. 2013; Vol 7 (Issue 4); 881-888.
[10] Brissette, A. Hoke, A. Traube, J. Fenglong Lu Maksimovizc, D. Study on the effect of solar irradiance
intermittency mitigation on electric vehicle battery lifetime. Technologies for Sustainability (SusTech) IEEE
Conference. Aug 2013; 262 – 267.
[11] Udawatta, L. Madawala, Muthumuni, D. Vilathgamuwa, M. Control of solar powered micro-grids using electric
vehicles. Sustainable Energy Technologies (ICSET) IEEE Conference. Sept 2012; 270 – 275.
[12] Changsong Chen, Huazhong, Wuhan, Shanxu Duan. Optimal Integration of Plug-in-Hybrid Electric Vehicles in
Microgrid. IEEE Transaction on Industrial Informatics. 2014; Vol 10 (Issue 3); 1917-1926.
[13] Patterson, M., SkySong, Scottsdale, Macia, N.F., Kannan, A.M. Hybrid Microgrid Model Based on Solar
Photovoltaic Battery Fuel Cell System for Intermittent Load Applications. IEEE Transaction on Energy
Conversion. Feb 2015; 359-366.
[14] Kumaravel, S., Ashok, S. Adapted Multilayer feedforward ANN based Power Management Control of Solar
Photovoltaic and wind Integrated Power Systems. Innovative Smart Grid Technologies - India (ISGT India) IEEE
PES. 2011; 223-228.
BIOGRAPHIES OF AUTHORS
E. Sheeba Percis obtained her B.E. from Madras University and M.E. from Anna University.
Currently she is pursuing Ph.D. in Dr. M.G.R. Educational & Research Institute. Her specialization
in PG is Power Electronics and Drives. Her research interests include Renewable Energy
Technology, Power System Simulation studies, Power Electronics, Transmission and Distribution.
She is presently working as Associate Professor of Electrical and Electronics Engineering
Department at Dr. MGR Educational and Research Institute, Chennai, TamilNadu, India.
S. Manivannan obtained his B.E. and M.E. from Madras University and PhD from Anna
University. His specialisation includes thermal and EMI management of electronic packages,
electromagnetic compatibility, Power System Simulation studies and optimisation. He is presently
working as the Deputy Dean and Professor of Electrical and Electronics Engineering at Dr. MGR
Educational and Research Institute University, Chennai, TamilNadu, India. He has published over
ten papers in referred indexed international journals and presented many papers in conferences.
A. Nalini obtained her B.E. and M.E. from Annamalai University. Currently she is pursuing Ph.D.
in Dr. M.G.R. Educational & Research Institute. Her specialization in PG is Power Systems. Her
research interests include Wide Area Monitoring and Control, Phasor Measurement Unit, Power
System Simulation studies and Optimization. She is presently working as Associate Professor of
Electrical and Electronics Engineering Department at Dr. MGR Educational and Research
Institute, Chennai, TamilNadu, India.