Eci
•
0 likes•228 views
This document provides instructions for an electrical circuits and instrumentation practical exam for an Electronics and Communication Engineering course. It lists 15 experiments for students to complete, including verifying Ohm's law, Kirchoff's laws, superposition theorem, Thevenin's theorem, and Norton's theorem. It also includes experiments involving series and parallel resonant circuits, calibrating ammeters and voltmeters, using a Wheatstone bridge, measuring signals with an oscilloscope, and determining characteristics of devices like LVDT, strain gauges, thermistors, and load cells. Marks are allocated for circuit diagram, connection, execution, output/result, and viva voce with a total of 75 marks.
Report
Share
Report
Share
Download to read offline
Recommended
Lab1
This document discusses different load configurations (star, delta) for a 3-phase circuit with a line-to-line voltage of 208V and line impedance of 15 ohms. It analyzes balanced and unbalanced resistive and RL loads. It also includes a theoretical verification of power calculations for a balanced delta resistive load, showing the line current and power match the theoretical values calculated.
lcr circuit implementation using matlab
This document discusses implementing RLC circuits using MATLAB. It first provides a brief overview of RLC circuits, noting they have a resistor, inductor and capacitor. It then discusses calculating effective resistance using impedance and modeling series RLC circuits using equations involving voltage, current and resistance. The document concludes by showing MATLAB code to plot the voltage of an undamped parallel RLC circuit over time by defining variables, calculating constants, and using plotting commands.
Mock test
This document contains instructions for 5 mock test questions on basic electrical circuit analysis. Question 1 asks to use source transformations to find current in a circuit if a 5 ohm resistor dissipates 15W of power. Question 2 asks to use network reduction techniques to find the current through a 10 ohm resistor. Question 3 asks to use mesh current analysis to find the value of R in a circuit. Question 4 asks to use nodal analysis to find the voltage Vx in a circuit. Question 5 asks to derive the expression for voltage discharge of a capacitor through a resistor and plot the graph.
Matlab solving rlc circuit
This document discusses solving RLC series parallel circuits using Simulink. It introduces Kirchhoff's voltage law and differentiating the voltage equations to express the RLC response in general form. It provides a Simulink model for a series RLC circuit and instructs the reader to change component values and make a parallel RLC model. It also introduces the SimPowerSystems library for modeling electrical systems in Simulink and lists some commonly used blocks with an example circuit.
Electrical characteristics of MOSFET
This document summarizes the electrical characteristics of n-channel MOSFETs. It describes the minority carrier concentration in the depletion region and how the depletion width changes with applied gate voltage. It then discusses the threshold voltage expression and how the threshold is affected by factors like bulk charge, fixed oxide charge and work function differences. Finally, it derives the drain current equation and shows how the I-V characteristics are affected by channel length modulation under different regions of operation.
Absorption coefficient of quantum well structure
The document discusses the absorption coefficient in a quantum well for intraband transitions between energy levels. It presents the formula for absorption coefficient as a function of oscillator strength between levels, doping density, and Lorentzian lineshape. It derives the oscillator strength between the two lowest consecutive states in terms of the quantum well width. The absorption coefficient is then incorporated with a Lorentzian lineshape to better fit practical experimental data.
123
This document appears to be a lab manual for basic electronics experiments. It contains 11 experiments covering topics like semiconductor diodes, rectifiers, transistors, FETs, and voltage regulators. Each experiment section includes the aim, apparatus, circuit diagram, theory, procedure, observations/results, and conclusion. The manual is intended for use by students at Samarth College of Engineering and Technology to learn practical skills in basic electronics components and circuits.
Kirchhoff’s laws
Kirchhoff's laws describe how electric current and voltage behave in circuits:
1) Kirchhoff's Current Law states that the total current entering a junction must equal the total current leaving it.
2) Kirchhoff's Voltage Law states that the sum of the voltages around any closed circuit loop is equal to zero. The voltage provided must equal the voltage used.
3) These laws allow analysis of complex circuits involving multiple batteries, cells, and circuit components by systematically tracing loops and applying the rules that voltage is positive when traveling in the direction of conventional current and negative when traveling opposite.
Recommended
Lab1
This document discusses different load configurations (star, delta) for a 3-phase circuit with a line-to-line voltage of 208V and line impedance of 15 ohms. It analyzes balanced and unbalanced resistive and RL loads. It also includes a theoretical verification of power calculations for a balanced delta resistive load, showing the line current and power match the theoretical values calculated.
lcr circuit implementation using matlab
This document discusses implementing RLC circuits using MATLAB. It first provides a brief overview of RLC circuits, noting they have a resistor, inductor and capacitor. It then discusses calculating effective resistance using impedance and modeling series RLC circuits using equations involving voltage, current and resistance. The document concludes by showing MATLAB code to plot the voltage of an undamped parallel RLC circuit over time by defining variables, calculating constants, and using plotting commands.
Mock test
This document contains instructions for 5 mock test questions on basic electrical circuit analysis. Question 1 asks to use source transformations to find current in a circuit if a 5 ohm resistor dissipates 15W of power. Question 2 asks to use network reduction techniques to find the current through a 10 ohm resistor. Question 3 asks to use mesh current analysis to find the value of R in a circuit. Question 4 asks to use nodal analysis to find the voltage Vx in a circuit. Question 5 asks to derive the expression for voltage discharge of a capacitor through a resistor and plot the graph.
Matlab solving rlc circuit
This document discusses solving RLC series parallel circuits using Simulink. It introduces Kirchhoff's voltage law and differentiating the voltage equations to express the RLC response in general form. It provides a Simulink model for a series RLC circuit and instructs the reader to change component values and make a parallel RLC model. It also introduces the SimPowerSystems library for modeling electrical systems in Simulink and lists some commonly used blocks with an example circuit.
Electrical characteristics of MOSFET
This document summarizes the electrical characteristics of n-channel MOSFETs. It describes the minority carrier concentration in the depletion region and how the depletion width changes with applied gate voltage. It then discusses the threshold voltage expression and how the threshold is affected by factors like bulk charge, fixed oxide charge and work function differences. Finally, it derives the drain current equation and shows how the I-V characteristics are affected by channel length modulation under different regions of operation.
Absorption coefficient of quantum well structure
The document discusses the absorption coefficient in a quantum well for intraband transitions between energy levels. It presents the formula for absorption coefficient as a function of oscillator strength between levels, doping density, and Lorentzian lineshape. It derives the oscillator strength between the two lowest consecutive states in terms of the quantum well width. The absorption coefficient is then incorporated with a Lorentzian lineshape to better fit practical experimental data.
123
This document appears to be a lab manual for basic electronics experiments. It contains 11 experiments covering topics like semiconductor diodes, rectifiers, transistors, FETs, and voltage regulators. Each experiment section includes the aim, apparatus, circuit diagram, theory, procedure, observations/results, and conclusion. The manual is intended for use by students at Samarth College of Engineering and Technology to learn practical skills in basic electronics components and circuits.
Kirchhoff’s laws
Kirchhoff's laws describe how electric current and voltage behave in circuits:
1) Kirchhoff's Current Law states that the total current entering a junction must equal the total current leaving it.
2) Kirchhoff's Voltage Law states that the sum of the voltages around any closed circuit loop is equal to zero. The voltage provided must equal the voltage used.
3) These laws allow analysis of complex circuits involving multiple batteries, cells, and circuit components by systematically tracing loops and applying the rules that voltage is positive when traveling in the direction of conventional current and negative when traveling opposite.
17444 power electronics
The document contains sample test papers for the subject of Power Electronics for a Diploma in Electronics Engineering program. It covers topics like rectifiers, choppers, inverters, thyristors, transistors, and power semiconductor devices. The test paper includes multiple choice and long answer questions to assess the understanding of circuit diagrams, characteristics, working principles and comparisons of various power electronic components and circuits.
Www educationsmaterials-com-2020-12-measurement-and-instrumentation-paper-html
Measurement and Instrumentation paper 2020 B.tech Department of Electronics and Communication Engineering-https://www.educationsmaterials.com/2020/12/measurement-and-instrumentation-paper.html
MATLAB SIMULATIONS OF SERIES RESONANT CIRCUIT
The document describes MATLAB simulations of a series resonant circuit. It includes functions to calculate the input impedance, input current, and output voltage of the circuit. Additional functions vary the resistor value and plot the input impedance, input current, natural response of current, and natural response of voltage for different resistances. The purpose is to better understand the operating characteristics of the series resonant circuit.
Calculations in electronics
Quick review of Series and parallel circuit behavior and intriduction of electronic measurements symbols and their units of measure.
RLC circuit
The document discusses the parallel RLC circuit and its response over time. It examines the circuit's behavior under different conditions such as being overdamped, critically damped, and underdamped. Graphs and equations are presented showing the voltage response of RLC circuits under these conditions. Examples are also provided of determining the current and voltage outputs of various RLC circuits over time.
Unipi digital integrated circuit configured to operate in the quantum hall...
Unipi digital integrated circuit configured to operate in the quantum hall...Toscana Open Research
The proposed electronic circuit exploits the quantum Hall effect and mainly aims to obtain a resistance standard, particularly for the calibration of different electronic devices.
CNTFET
The document discusses carbon nanotube field effect transistors (CNTFETs) as a potential replacement for MOSFETs. It describes some of the issues with continuously scaling down MOSFETs, and then provides details on different types of CNTFET designs and their advantages over MOSFETs, such as higher carrier mobility and transconductance. Some applications of CNTFETs are also mentioned. However, drawbacks include higher production costs and failure rates compared to traditional CMOS technology.
Quantum Electronics Lecture 7
This document is a lecture on the quantum Hall effect. It discusses how the resistance of a quantum well system becomes quantized under low temperature and high magnetic field conditions, known as the quantum Hall effect. It also provides calculations of the quantum Hall resistance, showing that it is constant and equal to h/q^2, where h is Planck's constant and q is the elementary charge. The significance is that the resistance remains constant as long as the Fermi level lies between localized states in the Landau bands formed under the magnetic field.
A10 pdc (1)
This document is a two page exam for a pulse and digital circuits course. It contains a 20 point multiple choice section and a 50 point long answer section. The long answer section asks students to answer 5 out of the 8 questions provided. The questions cover topics like RC filters, clamping circuits, multivibrators, logic gates, sampling gates, and flip flops. Students are asked to analyze circuits, derive expressions, draw waveforms, and compare different circuit types and logic families. The exam tests students' understanding of fundamental digital and pulse circuit concepts.
Lect06 handout
The document discusses Kirchhoff's laws, which describe how electric currents behave in circuits. It introduces Kirchhoff's Junction Rule, which states that the total current entering a junction equals the total current leaving it. It also introduces Kirchhoff's Loop Rule, which states that the sum of the voltage increases and decreases around any closed loop in a circuit is equal to zero. The document provides examples of how to apply these rules to solve for unknown currents in circuits. It also contains practice problems for students to work through applying Kirchhoff's laws.
ECA - Lecture 03
1) The document discusses basic circuit analysis techniques including circuit abstraction, voltage, current, resistance, nodes, branches, loops, and Kirchhoff's laws.
2) Key circuit concepts covered are open and short circuits, voltage and current division, and mesh analysis.
3) Mesh analysis involves identifying all loops in a circuit, labeling loop currents, applying Kirchhoff's laws, and solving equations to determine the currents through each component.
Tutorial 1 (review and solved porblems)
This document provides a tutorial on mass/inertia elements and solved examples of transfer functions for mechanical and electrical systems. It includes two examples of finding transfer functions for mechanical systems, one problem on a car suspension, and two examples of obtaining transfer functions and block diagrams for RC circuits.
3 nodal analysis
The document discusses the steps of nodal analysis which includes choosing a reference node, assigning voltages to nodes, applying Kirchhoff's Current Law (KCL) at each node to obtain equations relating currents and voltages, and solving the system of equations to determine node voltages. An example circuit is presented and nodal analysis is performed on it by defining node voltages, writing KCL equations, and solving to find the output voltage. Nodal analysis is a technique for analyzing electrical circuits by writing equations at nodes based on KCL.
Advanced MOSFET
This document discusses advanced MOSFET architectures and their advantages over traditional bulk MOSFETs. It describes issues with bulk MOSFETs like short channel effects and proposes solutions like multi-gate architectures and high-k dielectrics. Specifically, it examines double-gate MOSFETs, tri-gate MOSFETs, gate-all-around MOSFETs, SOI MOSFETs, FinFETs, and tunnel FETs, outlining their characteristics and benefits over other designs for low power electronics applications.
kirchoff law
This document discusses Kirchoff's laws, which are two circuit analysis laws developed by Gustav Kirchoff in 1845. The first law, known as Kirchoff's voltage law (KVL), states that the sum of the voltages around any closed loop in a circuit is equal to zero. The second law, known as Kirchoff's current law (KCL), states that the algebraic sum of the currents at any node or junction in a circuit is equal to zero. The document provides examples of applying KVL and KCL, including using mesh analysis, and contains three review questions about Kirchoff's laws and circuit analysis techniques.
Kirchh
The document discusses Kirchhoff's laws, which are two simple circuit analysis rules used to analyze electrical circuits. The junction rule states that the total current entering a junction must equal the total current leaving. The loop rule states that the algebraic sum of voltages around any closed loop in a circuit must be zero. An example of each rule is provided. The document also discusses sign conventions for applying the rules and uses of Kirchhoff's laws, such as determining currents and potential differences.
Feature iqswap
This document discusses phase shifts in digital TV signals and I/Q vectors. It explains that I/Q vectors can become inverted, swapping the in-phase and quadrature components of the signal. This causes some symbol pairs, like 10 and 01, to be reversed at the receiver. However, receivers can detect this automatically by looking for the synchronization byte which is fixed in the transport stream packets. Reversing the I/Q inversion at the receiver corrects the signal again.
Current Transformers: Ratio & Burden Testing
This presentation will give you an understanding of self contained and transformer rated current transformers. You will also discuss meter testing, CT testing, ratio & burden testing. 6/2014.
Lec4 Intro to Computer Engineering by Hsien-Hsin Sean Lee Georgia Tech -- CMOS
Lec4 Intro to Computer Engineering by Hsien-Hsin Sean Lee Georgia Tech -- CMOSHsien-Hsin Sean Lee, Ph.D.
1. The document describes CMOS inverters and how to construct CMOS networks for basic logic gates like NAND, NOR, and XOR from pull-up and pull-down networks.
2. It provides a systematic method for drawing the CMOS network from a Boolean equation by first constructing either the pull-up network or pull-down network based on the equation.
3. Examples are given to demonstrate how to apply the method to draw CMOS networks for equations with multiple variables like XOR, XNOR, and complex equations with nested terms.Calculated Values
This document contains calculations for resistances and voltages in an integrated circuit. It uses formulas to calculate the total resistance in series and parallel combinations. It then applies the voltage divider principle to determine voltages across specific resistances when a 10V source is applied. The calculations show the voltages across R1, R3, R4, and R5 are 5.15V, 4.85V, 1.58V, and 3.27V respectively.
Ee8661 ped lab set-1
This document outlines the experiments for a B.E Electrical and Electronics Engineering power electronics and drives laboratory practical exam. It lists 25 possible experiments students can choose from, related to topics like generating gate pulses, characteristics of controlled semiconductor devices, inverters, converters, and motor drives. The exam will be 3 hours and students must answer one question. Their work will be evaluated on various parameters like aim/procedure, tabulation/circuit drawing, calculations and results, and a viva voce, worth a total of 100 marks.
Power Electronics lab manual BE EEE
The manual is very useful for UG EEE students for the subject Power Electronics
By
M.MURUGANANDAM. M.E.,(Ph.D).,MIEEE.,MISTE,
Assistant Professor & Head / EIE,
Muthayammal Engineering College,
Rasipuram,
Namakkal-637 408.
Cell No: 9965768327
More Related Content
What's hot
17444 power electronics
The document contains sample test papers for the subject of Power Electronics for a Diploma in Electronics Engineering program. It covers topics like rectifiers, choppers, inverters, thyristors, transistors, and power semiconductor devices. The test paper includes multiple choice and long answer questions to assess the understanding of circuit diagrams, characteristics, working principles and comparisons of various power electronic components and circuits.
Www educationsmaterials-com-2020-12-measurement-and-instrumentation-paper-html
Measurement and Instrumentation paper 2020 B.tech Department of Electronics and Communication Engineering-https://www.educationsmaterials.com/2020/12/measurement-and-instrumentation-paper.html
MATLAB SIMULATIONS OF SERIES RESONANT CIRCUIT
The document describes MATLAB simulations of a series resonant circuit. It includes functions to calculate the input impedance, input current, and output voltage of the circuit. Additional functions vary the resistor value and plot the input impedance, input current, natural response of current, and natural response of voltage for different resistances. The purpose is to better understand the operating characteristics of the series resonant circuit.
Calculations in electronics
Quick review of Series and parallel circuit behavior and intriduction of electronic measurements symbols and their units of measure.
RLC circuit
The document discusses the parallel RLC circuit and its response over time. It examines the circuit's behavior under different conditions such as being overdamped, critically damped, and underdamped. Graphs and equations are presented showing the voltage response of RLC circuits under these conditions. Examples are also provided of determining the current and voltage outputs of various RLC circuits over time.
Unipi digital integrated circuit configured to operate in the quantum hall...
Unipi digital integrated circuit configured to operate in the quantum hall...Toscana Open Research
The proposed electronic circuit exploits the quantum Hall effect and mainly aims to obtain a resistance standard, particularly for the calibration of different electronic devices.
CNTFET
The document discusses carbon nanotube field effect transistors (CNTFETs) as a potential replacement for MOSFETs. It describes some of the issues with continuously scaling down MOSFETs, and then provides details on different types of CNTFET designs and their advantages over MOSFETs, such as higher carrier mobility and transconductance. Some applications of CNTFETs are also mentioned. However, drawbacks include higher production costs and failure rates compared to traditional CMOS technology.
Quantum Electronics Lecture 7
This document is a lecture on the quantum Hall effect. It discusses how the resistance of a quantum well system becomes quantized under low temperature and high magnetic field conditions, known as the quantum Hall effect. It also provides calculations of the quantum Hall resistance, showing that it is constant and equal to h/q^2, where h is Planck's constant and q is the elementary charge. The significance is that the resistance remains constant as long as the Fermi level lies between localized states in the Landau bands formed under the magnetic field.
A10 pdc (1)
This document is a two page exam for a pulse and digital circuits course. It contains a 20 point multiple choice section and a 50 point long answer section. The long answer section asks students to answer 5 out of the 8 questions provided. The questions cover topics like RC filters, clamping circuits, multivibrators, logic gates, sampling gates, and flip flops. Students are asked to analyze circuits, derive expressions, draw waveforms, and compare different circuit types and logic families. The exam tests students' understanding of fundamental digital and pulse circuit concepts.
Lect06 handout
The document discusses Kirchhoff's laws, which describe how electric currents behave in circuits. It introduces Kirchhoff's Junction Rule, which states that the total current entering a junction equals the total current leaving it. It also introduces Kirchhoff's Loop Rule, which states that the sum of the voltage increases and decreases around any closed loop in a circuit is equal to zero. The document provides examples of how to apply these rules to solve for unknown currents in circuits. It also contains practice problems for students to work through applying Kirchhoff's laws.
ECA - Lecture 03
1) The document discusses basic circuit analysis techniques including circuit abstraction, voltage, current, resistance, nodes, branches, loops, and Kirchhoff's laws.
2) Key circuit concepts covered are open and short circuits, voltage and current division, and mesh analysis.
3) Mesh analysis involves identifying all loops in a circuit, labeling loop currents, applying Kirchhoff's laws, and solving equations to determine the currents through each component.
Tutorial 1 (review and solved porblems)
This document provides a tutorial on mass/inertia elements and solved examples of transfer functions for mechanical and electrical systems. It includes two examples of finding transfer functions for mechanical systems, one problem on a car suspension, and two examples of obtaining transfer functions and block diagrams for RC circuits.
3 nodal analysis
The document discusses the steps of nodal analysis which includes choosing a reference node, assigning voltages to nodes, applying Kirchhoff's Current Law (KCL) at each node to obtain equations relating currents and voltages, and solving the system of equations to determine node voltages. An example circuit is presented and nodal analysis is performed on it by defining node voltages, writing KCL equations, and solving to find the output voltage. Nodal analysis is a technique for analyzing electrical circuits by writing equations at nodes based on KCL.
Advanced MOSFET
This document discusses advanced MOSFET architectures and their advantages over traditional bulk MOSFETs. It describes issues with bulk MOSFETs like short channel effects and proposes solutions like multi-gate architectures and high-k dielectrics. Specifically, it examines double-gate MOSFETs, tri-gate MOSFETs, gate-all-around MOSFETs, SOI MOSFETs, FinFETs, and tunnel FETs, outlining their characteristics and benefits over other designs for low power electronics applications.
kirchoff law
This document discusses Kirchoff's laws, which are two circuit analysis laws developed by Gustav Kirchoff in 1845. The first law, known as Kirchoff's voltage law (KVL), states that the sum of the voltages around any closed loop in a circuit is equal to zero. The second law, known as Kirchoff's current law (KCL), states that the algebraic sum of the currents at any node or junction in a circuit is equal to zero. The document provides examples of applying KVL and KCL, including using mesh analysis, and contains three review questions about Kirchoff's laws and circuit analysis techniques.
Kirchh
The document discusses Kirchhoff's laws, which are two simple circuit analysis rules used to analyze electrical circuits. The junction rule states that the total current entering a junction must equal the total current leaving. The loop rule states that the algebraic sum of voltages around any closed loop in a circuit must be zero. An example of each rule is provided. The document also discusses sign conventions for applying the rules and uses of Kirchhoff's laws, such as determining currents and potential differences.
Feature iqswap
This document discusses phase shifts in digital TV signals and I/Q vectors. It explains that I/Q vectors can become inverted, swapping the in-phase and quadrature components of the signal. This causes some symbol pairs, like 10 and 01, to be reversed at the receiver. However, receivers can detect this automatically by looking for the synchronization byte which is fixed in the transport stream packets. Reversing the I/Q inversion at the receiver corrects the signal again.
Current Transformers: Ratio & Burden Testing
This presentation will give you an understanding of self contained and transformer rated current transformers. You will also discuss meter testing, CT testing, ratio & burden testing. 6/2014.
Lec4 Intro to Computer Engineering by Hsien-Hsin Sean Lee Georgia Tech -- CMOS
Lec4 Intro to Computer Engineering by Hsien-Hsin Sean Lee Georgia Tech -- CMOSHsien-Hsin Sean Lee, Ph.D.
1. The document describes CMOS inverters and how to construct CMOS networks for basic logic gates like NAND, NOR, and XOR from pull-up and pull-down networks.
2. It provides a systematic method for drawing the CMOS network from a Boolean equation by first constructing either the pull-up network or pull-down network based on the equation.
3. Examples are given to demonstrate how to apply the method to draw CMOS networks for equations with multiple variables like XOR, XNOR, and complex equations with nested terms.Calculated Values
This document contains calculations for resistances and voltages in an integrated circuit. It uses formulas to calculate the total resistance in series and parallel combinations. It then applies the voltage divider principle to determine voltages across specific resistances when a 10V source is applied. The calculations show the voltages across R1, R3, R4, and R5 are 5.15V, 4.85V, 1.58V, and 3.27V respectively.
What's hot (20)
Www educationsmaterials-com-2020-12-measurement-and-instrumentation-paper-html
Www educationsmaterials-com-2020-12-measurement-and-instrumentation-paper-html
Unipi digital integrated circuit configured to operate in the quantum hall...
Unipi digital integrated circuit configured to operate in the quantum hall...
Lec4 Intro to Computer Engineering by Hsien-Hsin Sean Lee Georgia Tech -- CMOS
Lec4 Intro to Computer Engineering by Hsien-Hsin Sean Lee Georgia Tech -- CMOS
Similar to Eci
Ee8661 ped lab set-1
This document outlines the experiments for a B.E Electrical and Electronics Engineering power electronics and drives laboratory practical exam. It lists 25 possible experiments students can choose from, related to topics like generating gate pulses, characteristics of controlled semiconductor devices, inverters, converters, and motor drives. The exam will be 3 hours and students must answer one question. Their work will be evaluated on various parameters like aim/procedure, tabulation/circuit drawing, calculations and results, and a viva voce, worth a total of 100 marks.
Power Electronics lab manual BE EEE
The manual is very useful for UG EEE students for the subject Power Electronics
By
M.MURUGANANDAM. M.E.,(Ph.D).,MIEEE.,MISTE,
Assistant Professor & Head / EIE,
Muthayammal Engineering College,
Rasipuram,
Namakkal-637 408.
Cell No: 9965768327
CSE-I-BASIC ELECTRICALS ENGG. L1.pdf
This document outlines the syllabus for a Basic Electrical Engineering course. It includes 5 modules that cover topics such as DC circuits using Ohm's law, electromagnetism, DC machines, single and three phase AC circuits, transformers, and induction motors. The course objectives are to impart basic electrical knowledge, develop circuit analysis skills, highlight various electrical devices, and improve teamwork abilities. Kirchhoff's laws and their applications to circuit analysis are also explained.
CSE-I-BASIC ELECTRICALS ENGG. L1_2.pdf
This document outlines the syllabus for a Basic Electrical Engineering course. It includes 5 modules that cover topics such as DC circuits using Ohm's law and Kirchhoff's laws, electromagnetism, DC machines, measuring instruments, single-phase AC circuits, domestic wiring, three-phase circuits, synchronous generators, transformers, and induction motors. The objectives are to impart basic electrical knowledge, develop circuit analysis skills, highlight applications of generators, motors, and transformers, and emphasize safety. References and a detailed module-by-module breakdown are provided.
Electrical Circuit Lab
The document provides information about the electrical engineering lab manual for the third semester, including the index, syllabus, instructions, lab ethics guidelines, and experiments. It outlines 12 experiments focused on writing programs in C and PSPICE to analyze and simulate DC, AC, and transient behavior of circuits. The first experiment involves drawing circuit symbols for common electrical components.
Modeling and Simulation Lab Manual ME PED
This manual is very much useful for PG students belongs to ME Power Electronics and Drives
By
M.MURUGANANDAM. M.E.,(Ph.D).,MIEEE.,MISTE,
Assistant Professor & Head / EIE,
Muthayammal Engineering College,
Rasipuram,
Namakkal-637 408.
Cell No: 9965768327
Beee
This document provides a summary of a lecture on series RLC circuits. It begins with objectives of analyzing series RL, RC, and RLC circuits. It then derives the phasor diagrams for each circuit, showing voltage and current relationships. Key points covered include impedance, power factor, and phase angle calculations. Example questions are provided for reinforcement. The intended learning outcomes are for students to understand the concepts and phasor representations of series R, L, C circuits.
Experiment 1.1.pptx
This document provides information about an experiment to verify Kirchhoff's current law in a basic electrical and electronics engineering lab course. The objectives are to introduce Kirchhoff's current law and have students measure current and resistance in circuits to verify that the law holds true. The document outlines the required equipment, breadboard and multimeter use, the theory behind Kirchhoff's current law, an example circuit, observations that would be recorded, and expected learning outcomes.
Experiment 3.pptx
The document provides information about a lab experiment on determining the power factor of a series RL circuit. It includes the objective, apparatus required, theory, circuit diagram, calculations, observations, learning outcomes, assessment pattern and references. The objective is to demonstrate a series RL circuit and determine the power factor. The required apparatus are an AC supply, variac, wattmeter, ammeter, voltmeter, variable resistive and inductive loads. Calculations involve determining power factor using equations for power, voltage, current and phase angle. Students will learn to make series connections and measure circuit parameters to calculate impedance and power factor.
Gopi 1 lab manual
The document is a laboratory manual for an electronics lab course. It contains instructions for students and outlines 18 experiments on topics like rectifier circuits, transistor characteristics, amplifier frequency response, logic gates, and counters. The first experiment is on designing and testing full-wave rectifier circuits using a center-tapped transformer and bridge rectifier, both with and without a filter capacitor. It provides objectives, components, procedures, observations tables and calculations for determining voltage, current, ripple factor, regulation, and efficiency. Key aspects like waveforms and important concepts are also discussed.
Em waves lab assignment converted
The document provides details of 5 experiments conducted on electromagnetic waves as part of a laboratory course. Experiment 1 verifies the relationship between voltage, electric field and spacing of a parallel plate capacitor. Experiment 2 measures the capacitance and capacitance per unit length of coaxial cables of different lengths. Experiment 3 similarly measures inductance and inductance per unit length of coaxial cables. Experiment 4 determines the characteristic impedance of coaxial cables using measurements from Experiments 2 and 3. Experiment 5 verifies that the product of input impedances of a coaxial line with open and short circuits at the load end equals the characteristic impedance squared.
Expt1_Electronic Principles and Circuits Lab Manual_BEC303_18-11-2023.pptx
This document describes an experiment on bridge rectifier circuits. It contains:
1) An introduction to the BEC 303 electronics course and the objectives of experiment 1a on bridge rectifiers.
2) Details of the circuit design, components used, calculations for ripple factor, efficiency and regulation.
3) Procedures to set up the circuit in a simulator, make observations with and without a filter capacitor, and calculate performance metrics.
4) A second experiment on using a zener diode as a voltage regulator, covering the circuit, design considerations, procedure and observations.
Electrical machines-lab-i-ee0209
This document contains instructions for conducting load tests on a self-excited DC shunt generator. It outlines the apparatus needed, including ammeters, voltmeters, rheostats, and a tachometer. The procedure describes adjusting the field rheostat to vary the field current and record open circuit voltage measurements. Load is then applied in steps using a rheostatic load, and armature current, voltage, and speed are measured to plot the generator's load characteristics curves. The goal is to determine the generator's performance under no load and varying load conditions.
E&e lab manual
- The document is an electrical and electronics laboratory manual containing instructions for various experiments.
- It includes two parts - Part A contains experiments related to basic circuit theorems like superposition, reciprocity, Thevenin's, Norton's theorems. Part B includes experiments on basic electronic components like PN junction, diode characteristics.
- The given experiment is about verifying Thevenin's and Norton's theorems for a given circuit. It describes the circuit diagram, theoretical background, procedure to determine equivalent Thevenin's voltage and resistance or Norton's current and resistance.
EE6511-Control and Instrumentation Laboratory VALLIAMMAI CLG.pdf
This document contains information related to the Control and Instrumentation laboratory manual for the Department of Electrical and Electronics Engineering at Valliammai Engineering College for the 2016-2017 academic year. It includes:
1. Contact details for the laboratory instructors and assistants.
2. An index and syllabus outlining the experiments to be conducted over two cycles covering topics in control systems and instrumentation.
3. Details of the individual experiments including aims, apparatus required, theories, procedures, sample calculations and review questions.
4. Circuit diagrams related to the experiments involving bridges and other circuits.
The document provides a comprehensive overview and guidance for students regarding the laboratory curriculum, experiments, and assessments for the EE
EE6511-Control and Instrumentation Laboratory VALLIAMMAI CLG.pdf
This document contains the laboratory manual for the course EE6511 Control and Instrumentation. It includes:
1) An index listing the experiments to be performed.
2) The syllabus covering topics in control systems and instrumentation.
3) Details of two cycles of experiments to be completed.
4) Circuit diagrams and procedures for specific experiments measuring things like resistance, inductance, and capacitance using bridges.
5) Instructions for experiments involving transducers, meters, converters, and control systems.
The document provides students and instructors with comprehensive information on the experiments, objectives, procedures, and measurements for the control and instrumentation laboratory course.
Extra high voltage long ac transmission lines
From economical point of view designing of transmission line system is very important in the electricity supply system. Extra High Voltage Transmission Lines are best suited for transmission of bulk power.
TESCO Tuesday: Ratio, Burden and Admittance
This document provides an overview and agenda for an advanced training session on field CT testing. It discusses the key topics of ratio, burden, and admittance testing to evaluate the functionality and health of current transformers (CTs). The summary discusses:
- Ratio testing measures the proportional relationship between primary and secondary currents.
- Burden testing checks that CTs maintain accurate ratios with varying levels of burden on the secondary loop, up to specified limits.
- Admittance testing uses injected audio signals to evaluate the overall "health" of the CT's secondary loop in millisiemens values. Interpreting the results requires analysis to understand implications.
- Demagnetization procedures are also covered to address issues like
Verification of kirchoff current and voltage laws
This document describes an experiment to verify Kirchhoff's current law (KCL) and voltage law (KVL) in electrical circuits. It provides the circuit diagrams and component values used. For KCL, the total current measured equals the sum of individual branch currents. For KVL, the voltages around loops add up to the supplied voltage. Procedures are given to set up the circuits and measure voltages and currents to record in a table, in order to verify KCL and KVL.
Similar to Eci (20)
Expt1_Electronic Principles and Circuits Lab Manual_BEC303_18-11-2023.pptx
Expt1_Electronic Principles and Circuits Lab Manual_BEC303_18-11-2023.pptx
EE6511-Control and Instrumentation Laboratory VALLIAMMAI CLG.pdf
EE6511-Control and Instrumentation Laboratory VALLIAMMAI CLG.pdf
EE6511-Control and Instrumentation Laboratory VALLIAMMAI CLG.pdf
EE6511-Control and Instrumentation Laboratory VALLIAMMAI CLG.pdf
Recently uploaded
BÀI TẬP BỔ TRỢ TIẾNG ANH LỚP 9 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2024-2025 - ...
BÀI TẬP BỔ TRỢ TIẾNG ANH LỚP 9 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2024-2025 - ...Nguyen Thanh Tu Collection
https://app.box.com/s/tacvl9ekroe9hqupdnjruiypvm9rdanePhilippine Edukasyong Pantahanan at Pangkabuhayan (EPP) Curriculum
(𝐓𝐋𝐄 𝟏𝟎𝟎) (𝐋𝐞𝐬𝐬𝐨𝐧 𝟏)-𝐏𝐫𝐞𝐥𝐢𝐦𝐬
𝐃𝐢𝐬𝐜𝐮𝐬𝐬 𝐭𝐡𝐞 𝐄𝐏𝐏 𝐂𝐮𝐫𝐫𝐢𝐜𝐮𝐥𝐮𝐦 𝐢𝐧 𝐭𝐡𝐞 𝐏𝐡𝐢𝐥𝐢𝐩𝐩𝐢𝐧𝐞𝐬:
- Understand the goals and objectives of the Edukasyong Pantahanan at Pangkabuhayan (EPP) curriculum, recognizing its importance in fostering practical life skills and values among students. Students will also be able to identify the key components and subjects covered, such as agriculture, home economics, industrial arts, and information and communication technology.
𝐄𝐱𝐩𝐥𝐚𝐢𝐧 𝐭𝐡𝐞 𝐍𝐚𝐭𝐮𝐫𝐞 𝐚𝐧𝐝 𝐒𝐜𝐨𝐩𝐞 𝐨𝐟 𝐚𝐧 𝐄𝐧𝐭𝐫𝐞𝐩𝐫𝐞𝐧𝐞𝐮𝐫:
-Define entrepreneurship, distinguishing it from general business activities by emphasizing its focus on innovation, risk-taking, and value creation. Students will describe the characteristics and traits of successful entrepreneurs, including their roles and responsibilities, and discuss the broader economic and social impacts of entrepreneurial activities on both local and global scales.
clinical examination of hip joint (1).pdf
described clinical examination all orthopeadic conditions .
BBR 2024 Summer Sessions Interview Training
Qualitative research interview training by Professor Katrina Pritchard and Dr Helen Williams
Gender and Mental Health - Counselling and Family Therapy Applications and In...
A proprietary approach developed by bringing together the best of learning theories from Psychology, design principles from the world of visualization, and pedagogical methods from over a decade of training experience, that enables you to: Learn better, faster!
The History of Stoke Newington Street Names
Presented at the Stoke Newington Literary Festival on 9th June 2024
www.StokeNewingtonHistory.com
Wound healing PPT
This document provides an overview of wound healing, its functions, stages, mechanisms, factors affecting it, and complications.
A wound is a break in the integrity of the skin or tissues, which may be associated with disruption of the structure and function.
Healing is the body’s response to injury in an attempt to restore normal structure and functions.
Healing can occur in two ways: Regeneration and Repair
There are 4 phases of wound healing: hemostasis, inflammation, proliferation, and remodeling. This document also describes the mechanism of wound healing. Factors that affect healing include infection, uncontrolled diabetes, poor nutrition, age, anemia, the presence of foreign bodies, etc.
Complications of wound healing like infection, hyperpigmentation of scar, contractures, and keloid formation.
How to Make a Field Mandatory in Odoo 17
In Odoo, making a field required can be done through both Python code and XML views. When you set the required attribute to True in Python code, it makes the field required across all views where it's used. Conversely, when you set the required attribute in XML views, it makes the field required only in the context of that particular view.
How to Create a More Engaging and Human Online Learning Experience
How to Create a More Engaging and Human Online Learning Experience Wahiba Chair Training & Consulting
Wahiba Chair's Talk at the 2024 Learning Ideas Conference. What is Digital Literacy? A guest blog from Andy McLaughlin, University of Ab...
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Aberdeen
Walmart Business+ and Spark Good for Nonprofits.pdf
"Learn about all the ways Walmart supports nonprofit organizations.
You will hear from Liz Willett, the Head of Nonprofits, and hear about what Walmart is doing to help nonprofits, including Walmart Business and Spark Good. Walmart Business+ is a new offer for nonprofits that offers discounts and also streamlines nonprofits order and expense tracking, saving time and money.
The webinar may also give some examples on how nonprofits can best leverage Walmart Business+.
The event will cover the following::
Walmart Business + (https://business.walmart.com/plus) is a new shopping experience for nonprofits, schools, and local business customers that connects an exclusive online shopping experience to stores. Benefits include free delivery and shipping, a 'Spend Analytics” feature, special discounts, deals and tax-exempt shopping.
Special TechSoup offer for a free 180 days membership, and up to $150 in discounts on eligible orders.
Spark Good (walmart.com/sparkgood) is a charitable platform that enables nonprofits to receive donations directly from customers and associates.
Answers about how you can do more with Walmart!"
Solutons Maths Escape Room Spatial .pptx
Solutions of Puzzles of Mathematics Escape Room Game in Spatial.io
Main Java[All of the Base Concepts}.docx
This is part 1 of my Java Learning Journey. This Contains Custom methods, classes, constructors, packages, multithreading , try- catch block, finally block and more.
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...Nguyen Thanh Tu Collection
https://app.box.com/s/qhtvq32h4ybf9t49ku85x0n3xl4jhr15Temple of Asclepius in Thrace. Excavation results
The temple and the sanctuary around were dedicated to Asklepios Zmidrenus. This name has been known since 1875 when an inscription dedicated to him was discovered in Rome. The inscription is dated in 227 AD and was left by soldiers originating from the city of Philippopolis (modern Plovdiv).
Recently uploaded (20)
BÀI TẬP BỔ TRỢ TIẾNG ANH LỚP 9 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2024-2025 - ...
BÀI TẬP BỔ TRỢ TIẾNG ANH LỚP 9 CẢ NĂM - GLOBAL SUCCESS - NĂM HỌC 2024-2025 - ...
Philippine Edukasyong Pantahanan at Pangkabuhayan (EPP) Curriculum
Philippine Edukasyong Pantahanan at Pangkabuhayan (EPP) Curriculum
Gender and Mental Health - Counselling and Family Therapy Applications and In...
Gender and Mental Health - Counselling and Family Therapy Applications and In...
How to Create a More Engaging and Human Online Learning Experience
How to Create a More Engaging and Human Online Learning Experience
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Ab...
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Ab...
Walmart Business+ and Spark Good for Nonprofits.pdf
Walmart Business+ and Spark Good for Nonprofits.pdf
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...
BÀI TẬP DẠY THÊM TIẾNG ANH LỚP 7 CẢ NĂM FRIENDS PLUS SÁCH CHÂN TRỜI SÁNG TẠO ...
B. Ed Syllabus for babasaheb ambedkar education university.pdf
B. Ed Syllabus for babasaheb ambedkar education university.pdf
Eci
- 1. 34035 INSTRUMENTAION PRACTICAL DIPLOMA IN ELECTRONICS AND COMMUNICAITON CENTRALISED QUESTION BANK DIRECTORATE OF TECHNICAL EDUCATION GOVERNMENT OF TAMILNADU 4035 - ELECTRICAL CIRCUITS AND INSTRUMENTAION PRACTICAL ELECTRONICS AND COMMUNICAITON ENGINEERING CENTRALISED QUESTION BANK DIRECTORATE OF TECHNICAL EDUCATION GOVERNMENT OF TAMILNADU LECTRICAL CIRCUITS AND INSTRUMENTAION PRACTICAL ELECTRONICS AND COMMUNICAITON DIRECTORATE OF TECHNICAL EDUCATION
- 2. Course Name : Electronics and Communication Engineering Subject code : 34035 Semester : III Semester Subject title : ELECTRICAL CIRCUITS & INSTRUMENTATION PRACTICAL Note: Different component values should be given for each batch of students by the External Examiner 1. Construct a circuit to verify ohm’s law. (By varying resistance- minimum 5 values). 2. a. Construct a circuit to verify kirchoff’s voltage law. b. Construct a circuit to verify kirchoff’s current law. 3. Construct a circuit to verify Superposition theorem. 4. Construct a circuit to verify Thevenin’s Theorem. 5. Construct a circuit to verify Norton’s Theorem. 6. Construct a circuit to verify Maximum power transfer Theorem. 7. a. Construct and test the performance of series resonant circuit . b. Construct and test the performance of parallel resonant circuit. 8. Conduct the experiment to calibrate the given ammeter and voltmeter 9. Construct and test the performance of Wheatstone bridge 10. Conduct the experiment to measure the amplitude and frequency of signals using dual trace CRO 11. a. Conduct the experiment to measure the unknown frequency using CRO by Lissajous figure.(by generating minimum 4 patterns). b. Conduct the experiment to measure the unknown phase angle using CRO by Lissajous figure. 12. Conduct the experiment to test the performance of LVDT and plot its characteristics.
- 3. 13. Conduct the experiment to measure strain using strain gauge. 14. Conduct the experiment to determine the characteristics of a thermistor 15. Conduct the experiment to test the performance of a load cell ALLOCATION OF MARKS : CIRCUIT DIAGRAM 20 Marks CONNECTION 25 Marks EXECUTION 15 Marks OUTPUT / RESULT 10 Marks VIVA – VOCE 5 Marks TOTAL 75 Marks