This document reviews the stir casting process for producing aluminum metal matrix composites reinforced with ceramic particles. It discusses key parameters of the stir casting process that must be controlled, including stirrer design and speed, stirring temperature and time, reinforcement feed rate, and pouring temperature. The document summarizes several studies that used stir casting to fabricate aluminum composites with ceramic particles like silicon carbide and found they could achieve homogeneous dispersion of particles in the aluminum matrix when properly controlling the various stir casting parameters. Increasing the ceramic particle content was found to improve properties up to a point but higher levels led to more porosity and clustering of particles.
Fabrication and Wear Behavior of Particulate Reinforced Metal Matrix Composit...IOSRJMCE
The composites refer to the material consisting of two or more individual constituents, in that the reinforcing particulates are embedded to the base matrix to form composite materials by improving the mechanical and tribological properties. Different types of composite materials are available and these are increasing because of their good enhanced properties, among these Metal Matrix Composites (MMCs) finds its applications in various aspects like aerospace, automotive, defense, and marine etc. These improved properties are obtained from different form of particulates which are different in their aspect ratio are mixed with base material to provide good bonding and strength between them. To obtain these enhanced properties different manufacturing techniques are followed to prepare the composites. This paper presents an overview of types of composites, different fabrication techniques available to prepare the composites and also wear behavior of particulates reinforced MMC’s by studying different types of wear mechanism.
Development of Aluminium Metal Matrix Composite Using Stir Casting Methodtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
Evaluation of Mechanical Properties of Aluminum Alloy-Alumina-Boron Carbide M...Premier Publishers
The importance of composites as engineering materials is considered by the fact that out of over 1600 engineering materials available in the market today consists of 200 composites. These composites initially are Cast Iron and Bronze alloys but owing to their poor wear and seizure resistance, they were subjected to many experiments and the wear behavior of these composites were traversed to a maximum extent and were reported by number of research scholars for the past 25 years. In the present study based on the literature review, the effect of Boron Carbide on Stir Cast Aluminum Metal Matrix Composites is discussed. aluminum hybrid composites are a new generation of metal matrix composites that have the potentials of satisfying the demands of advanced engineering applications such as in aerospace, automobile, space, underwater and transportation applications. This is mainly due to upgraded mechanical and tribological properties like stiff, strong, abrasion and impact resistant and is not easily corroded. This paper attempts to review the different combination and configuration of reinforcing materials used in processing of hybrid aluminum matrix composites and how it effects the mechanical, corrosion and wear performance of the materials.
Fabrication, charecterization and development of high damping materials for n...eSAT Journals
Abstract Aluminum matrix composites are early inventions during 60’s. Presently these are used as railroad equipment and aerospace components. Their application has shown no further growth during the last decade due to lack of toughness. The non-compatibility between the matrix and the reinforcement and lack of good interface among these led to the reduced ductility levels. The limited solubility leads to the alloy formation passing solid solution strengthening while the un dissolved particles help achieving dispersion strengthening. Instead of taking ceramic particulates as reinforcements, metallic reinforcements were dispersed in aluminium matrix. Damping characteristics were calculated for the alloy and composites. Suitable heat treatment enhances the properties of the composite further. The expected mechanical properties will be higher than the regular alloys, which can be useful for various components in naval applications where high damping is required. Keywords: Dispersion Strengthening, Damping.
Fabrication and Wear Behavior of Particulate Reinforced Metal Matrix Composit...IOSRJMCE
The composites refer to the material consisting of two or more individual constituents, in that the reinforcing particulates are embedded to the base matrix to form composite materials by improving the mechanical and tribological properties. Different types of composite materials are available and these are increasing because of their good enhanced properties, among these Metal Matrix Composites (MMCs) finds its applications in various aspects like aerospace, automotive, defense, and marine etc. These improved properties are obtained from different form of particulates which are different in their aspect ratio are mixed with base material to provide good bonding and strength between them. To obtain these enhanced properties different manufacturing techniques are followed to prepare the composites. This paper presents an overview of types of composites, different fabrication techniques available to prepare the composites and also wear behavior of particulates reinforced MMC’s by studying different types of wear mechanism.
Development of Aluminium Metal Matrix Composite Using Stir Casting Methodtheijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
Evaluation of Mechanical Properties of Aluminum Alloy-Alumina-Boron Carbide M...Premier Publishers
The importance of composites as engineering materials is considered by the fact that out of over 1600 engineering materials available in the market today consists of 200 composites. These composites initially are Cast Iron and Bronze alloys but owing to their poor wear and seizure resistance, they were subjected to many experiments and the wear behavior of these composites were traversed to a maximum extent and were reported by number of research scholars for the past 25 years. In the present study based on the literature review, the effect of Boron Carbide on Stir Cast Aluminum Metal Matrix Composites is discussed. aluminum hybrid composites are a new generation of metal matrix composites that have the potentials of satisfying the demands of advanced engineering applications such as in aerospace, automobile, space, underwater and transportation applications. This is mainly due to upgraded mechanical and tribological properties like stiff, strong, abrasion and impact resistant and is not easily corroded. This paper attempts to review the different combination and configuration of reinforcing materials used in processing of hybrid aluminum matrix composites and how it effects the mechanical, corrosion and wear performance of the materials.
Fabrication, charecterization and development of high damping materials for n...eSAT Journals
Abstract Aluminum matrix composites are early inventions during 60’s. Presently these are used as railroad equipment and aerospace components. Their application has shown no further growth during the last decade due to lack of toughness. The non-compatibility between the matrix and the reinforcement and lack of good interface among these led to the reduced ductility levels. The limited solubility leads to the alloy formation passing solid solution strengthening while the un dissolved particles help achieving dispersion strengthening. Instead of taking ceramic particulates as reinforcements, metallic reinforcements were dispersed in aluminium matrix. Damping characteristics were calculated for the alloy and composites. Suitable heat treatment enhances the properties of the composite further. The expected mechanical properties will be higher than the regular alloys, which can be useful for various components in naval applications where high damping is required. Keywords: Dispersion Strengthening, Damping.
MECHANICAL BEHAVIOUR OF COMPOSITE MATERIALS IN METALIAEME Publication
Composite materials have gained traction in the world today and are becoming of common use in industrial and specialized applications in general due to their flexible nature that involves mixing through layers or matrixes the components of various substances and therefore, a percentage of each substance’s physical properties. In recent years there has been an increasing concern for industries to use cost effective reinforcement for metal materials like aluminum which is abundant cheap, with various desirable properties like its lightness, but lacks the strength for various applications – ceramic materials such as SiC and aluminum oxide are used generally for reinforcing the aluminum MMC. There is a good probability, backed up by tests for certain materials, that reinforcing metals with composites can increase failure displacement, fatigue life, ultimate failure load and energy absorption capacity, amongst many others by substantial amounts.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Aluminium Matrix Composites (AMC’s) are widely used in aerospace, automotive,
structural and marine applications due to their high strength to weight ratio, corrosion
resistance. In AMC one of constituent is aluminium or its alloy which forms a network
called as matrix phase and other constituent is embedded in matrix made of harder material
generally ceramic or non metallic material called as reinforcement. Various processing
techniques are available for manufacturing of AMC’s. Stir casting is one of the economical
and extensively used methods to enhance attractive properties of AMC’s. This paper
presents an overview of stir casing process, process parameter and preparation of AMC
using aluminium alloy as matrix phase and alumina (Al2O3) as reinforcement by varying
their proportion.
Evaluation of Mechanical properties of Aluminium based MMCBishal Bhandari
The aluminum 6061 MMC with Graphite,Fly ash and Magnesium used as reinforcement has got the higher value of hardness, toughness,less wear rate and less ductility compared to pure aluminium. Hence this composite can be deployed to make an piston rods,bush,aircraft body and automotive body parts.
Experimental Study of Wear Rate Coefficient of Aluminium Hybrid Composites Ma...AM Publications
In current decade, demand in material characteristics like light weight, superior strength to weight ratio, improved surface properties and enhanced wear resistance for complex engineering applications like automobile, aerospace and nuclear are researcher’s interest. However, performance of hybrid composites depends on right combination of reinforcements. Silicon carbide, silicon nitride, boron nitride and titanium carbide are few reinforcements available at present. In this work, Al356 is reinforced with SiC and B4C to enhance the mechanical properties, surface hardness and wear resistance. This hybrid composite is prepared by stir casting technique and the morphology of composite is studied using optical microscope to investigate the dispersion of reinforcements. In the present study, the wear and friction characteristics of hybrid composites are investigated using pin on disc dry wear tests by varying the load and speed and the results are tabulated for load vs mass loss, load vs wear rate and load vs wear coefficient. The results report that wear rate of hybrid composites are lower than that of binary composites. Mechanical properties, surface hardness and wear characteristics of aluminium hybrid composites are compared with that of aluminium binary composites available at present.
An Overview on Different Processing Parameters in Particulate Reinforced Meta...IJERA Editor
In the past few years the global need for reduced weight, low cost, high wear resistance and good quality materials has caused a shift in research from monolithic to composite materials. Metal Matrix Composites (MMCs) have evoked a keen interest in recent times for potential applications in marine, aerospace and automotive industries owing to their superior strength to weight ratio and high temperature resistance. Driving force for the utilization of AMCs include performance, economic and environmental benefits. The widespread adoption of particulate metal matrix composites for engineering applications has been hindered by the high cost of producing components. Achieving a uniform distribution of reinforcement within the matrix is one such challenge which impacts directly on the properties and quality of the composite material. In the case of particle reinforced metal matrix composites, the distribution of the reinforcement particles in the matrix alloy is influenced by several factors during casting. These include the rheological behaviour of the matrix melt, the particle incorporation method, interactions of the particles and the matrix before, during and after mixing, and the changing particle distribution during solidification. In this paper, research relevant to these factors which influences the particle distribution is reviewed and discussed in order to achieve a good distribution of reinforcement particles in a cast metal matrix composite (MMC).
APPLICATION OF ALUMINIUM HYBRID COMPOSITES IN AUTOMOTIVE INDUSTRYBlaza Stojanovic
Strict requirements that are put on mechanical constructions from the aspect of increase of exploitation periods and reduction of their weights, therefore of their prices as well, implicate developments and applications of new composite materials with matrices of lightweight metals. Composite materials with metal matrices are used for engine cylinders, pistons, disc and drum brakes, Cardan shafts and for other elements in automotive and aviation industry. The most important type of metallic materials is composite materials with matrices of aluminium alloys due to a set of their beneficial properties. Improvement of mechanical, especially tribological properties of hybrid composites were provided by the use of certain reinforce materials such as SiC, Al2O3 and graphite in defined weight or volumetric share. New developed hybrid composites with aluminium matrices have significantly higher resistance to wear, higher specific stiffness and higher resistance to fatigue. By the increase of quantities of produced elements made of hybrid composites, decrease of their prices is induced that even further enlarge their applications. The applications of aluminium hybrid composites are considered from the aspect and with the focus on automotive industry.
REVIEW ON EFFECT OF VARIOUS REINFORCEMENTS ON THE THERMAL PROPERTIES OF LM-25...IAEME Publication
For thermal management in applications like automobiles, aviation, marine etc. we need materials with high thermal conductivity, low coefficient of thermal expansion and at the same time the materials should have high strength, high corrosion resistance and low density. Aluminum alloys are excellent choices as the alloys possess all these properties. In order to improve the properties of the alloys further to make them more suitable for the applications, alloys are reinforced with different materials. This review focuses on influence on thermal properties of LM25 and some common light metal alloys reinforced with different materials, effect of heat and solution treatments on LM25/SiC MMC, effect of aging treatment on thermal fatigue of LM-25 alloy and the most common synthesis technique used
Aggregates sustainability through preparation of bituminous mixes at combined...eSAT Journals
Abstract Aggregates have to primarily bear load stresses and resist abrasive action of traffic movement under dry and wet conditions, when used in the surface course of the pavement. The aggregate gradation plays a vital role in securing desirable properties of resulting bituminous mixes. Different types of mixes are used under different conditions. Generally, the mixes are designed adopting midpoint gradation from the respective gradation tables. Often, the desired mix properties are not completely satisfied and needs some reworking of gradation. Sometimes the required quantity of aggregates may not be available in nearby areas so as to design a required type of mix. To overcome this, the desired aggregates may have to be brought from far off places, leading to time and cost escalation. This further aggravates the already prevailing scarcity of aggregates. Alternatively, if aggregates are available and satisfies the graduation requirements of two different type of mixes, attempt may be made to design a mix combining the gradation of two types of mixes. Possibly, the resulting mix could still satisfy the specified requirements. If so, the available aggregates could be used economically, without compromising on the quality of mixes. This would result in aggregate sustainability. With this objective, two types of bituminous mixes namely SDBC and BC were prepared at midpoint gradation of the specified ranges, as per MoRTH gradation tables and subsequently by combining the above two gradations taking average of the two midpoint gradations. The Marshall mix properties were compared and found that the mix requirements are largely satisfied at the combined gradation as well. Keywords: Aggregate, sustainability, bituminous mixes, midpoint gradation, combined gradation
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
MECHANICAL BEHAVIOUR OF COMPOSITE MATERIALS IN METALIAEME Publication
Composite materials have gained traction in the world today and are becoming of common use in industrial and specialized applications in general due to their flexible nature that involves mixing through layers or matrixes the components of various substances and therefore, a percentage of each substance’s physical properties. In recent years there has been an increasing concern for industries to use cost effective reinforcement for metal materials like aluminum which is abundant cheap, with various desirable properties like its lightness, but lacks the strength for various applications – ceramic materials such as SiC and aluminum oxide are used generally for reinforcing the aluminum MMC. There is a good probability, backed up by tests for certain materials, that reinforcing metals with composites can increase failure displacement, fatigue life, ultimate failure load and energy absorption capacity, amongst many others by substantial amounts.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Aluminium Matrix Composites (AMC’s) are widely used in aerospace, automotive,
structural and marine applications due to their high strength to weight ratio, corrosion
resistance. In AMC one of constituent is aluminium or its alloy which forms a network
called as matrix phase and other constituent is embedded in matrix made of harder material
generally ceramic or non metallic material called as reinforcement. Various processing
techniques are available for manufacturing of AMC’s. Stir casting is one of the economical
and extensively used methods to enhance attractive properties of AMC’s. This paper
presents an overview of stir casing process, process parameter and preparation of AMC
using aluminium alloy as matrix phase and alumina (Al2O3) as reinforcement by varying
their proportion.
Evaluation of Mechanical properties of Aluminium based MMCBishal Bhandari
The aluminum 6061 MMC with Graphite,Fly ash and Magnesium used as reinforcement has got the higher value of hardness, toughness,less wear rate and less ductility compared to pure aluminium. Hence this composite can be deployed to make an piston rods,bush,aircraft body and automotive body parts.
Experimental Study of Wear Rate Coefficient of Aluminium Hybrid Composites Ma...AM Publications
In current decade, demand in material characteristics like light weight, superior strength to weight ratio, improved surface properties and enhanced wear resistance for complex engineering applications like automobile, aerospace and nuclear are researcher’s interest. However, performance of hybrid composites depends on right combination of reinforcements. Silicon carbide, silicon nitride, boron nitride and titanium carbide are few reinforcements available at present. In this work, Al356 is reinforced with SiC and B4C to enhance the mechanical properties, surface hardness and wear resistance. This hybrid composite is prepared by stir casting technique and the morphology of composite is studied using optical microscope to investigate the dispersion of reinforcements. In the present study, the wear and friction characteristics of hybrid composites are investigated using pin on disc dry wear tests by varying the load and speed and the results are tabulated for load vs mass loss, load vs wear rate and load vs wear coefficient. The results report that wear rate of hybrid composites are lower than that of binary composites. Mechanical properties, surface hardness and wear characteristics of aluminium hybrid composites are compared with that of aluminium binary composites available at present.
An Overview on Different Processing Parameters in Particulate Reinforced Meta...IJERA Editor
In the past few years the global need for reduced weight, low cost, high wear resistance and good quality materials has caused a shift in research from monolithic to composite materials. Metal Matrix Composites (MMCs) have evoked a keen interest in recent times for potential applications in marine, aerospace and automotive industries owing to their superior strength to weight ratio and high temperature resistance. Driving force for the utilization of AMCs include performance, economic and environmental benefits. The widespread adoption of particulate metal matrix composites for engineering applications has been hindered by the high cost of producing components. Achieving a uniform distribution of reinforcement within the matrix is one such challenge which impacts directly on the properties and quality of the composite material. In the case of particle reinforced metal matrix composites, the distribution of the reinforcement particles in the matrix alloy is influenced by several factors during casting. These include the rheological behaviour of the matrix melt, the particle incorporation method, interactions of the particles and the matrix before, during and after mixing, and the changing particle distribution during solidification. In this paper, research relevant to these factors which influences the particle distribution is reviewed and discussed in order to achieve a good distribution of reinforcement particles in a cast metal matrix composite (MMC).
APPLICATION OF ALUMINIUM HYBRID COMPOSITES IN AUTOMOTIVE INDUSTRYBlaza Stojanovic
Strict requirements that are put on mechanical constructions from the aspect of increase of exploitation periods and reduction of their weights, therefore of their prices as well, implicate developments and applications of new composite materials with matrices of lightweight metals. Composite materials with metal matrices are used for engine cylinders, pistons, disc and drum brakes, Cardan shafts and for other elements in automotive and aviation industry. The most important type of metallic materials is composite materials with matrices of aluminium alloys due to a set of their beneficial properties. Improvement of mechanical, especially tribological properties of hybrid composites were provided by the use of certain reinforce materials such as SiC, Al2O3 and graphite in defined weight or volumetric share. New developed hybrid composites with aluminium matrices have significantly higher resistance to wear, higher specific stiffness and higher resistance to fatigue. By the increase of quantities of produced elements made of hybrid composites, decrease of their prices is induced that even further enlarge their applications. The applications of aluminium hybrid composites are considered from the aspect and with the focus on automotive industry.
REVIEW ON EFFECT OF VARIOUS REINFORCEMENTS ON THE THERMAL PROPERTIES OF LM-25...IAEME Publication
For thermal management in applications like automobiles, aviation, marine etc. we need materials with high thermal conductivity, low coefficient of thermal expansion and at the same time the materials should have high strength, high corrosion resistance and low density. Aluminum alloys are excellent choices as the alloys possess all these properties. In order to improve the properties of the alloys further to make them more suitable for the applications, alloys are reinforced with different materials. This review focuses on influence on thermal properties of LM25 and some common light metal alloys reinforced with different materials, effect of heat and solution treatments on LM25/SiC MMC, effect of aging treatment on thermal fatigue of LM-25 alloy and the most common synthesis technique used
Aggregates sustainability through preparation of bituminous mixes at combined...eSAT Journals
Abstract Aggregates have to primarily bear load stresses and resist abrasive action of traffic movement under dry and wet conditions, when used in the surface course of the pavement. The aggregate gradation plays a vital role in securing desirable properties of resulting bituminous mixes. Different types of mixes are used under different conditions. Generally, the mixes are designed adopting midpoint gradation from the respective gradation tables. Often, the desired mix properties are not completely satisfied and needs some reworking of gradation. Sometimes the required quantity of aggregates may not be available in nearby areas so as to design a required type of mix. To overcome this, the desired aggregates may have to be brought from far off places, leading to time and cost escalation. This further aggravates the already prevailing scarcity of aggregates. Alternatively, if aggregates are available and satisfies the graduation requirements of two different type of mixes, attempt may be made to design a mix combining the gradation of two types of mixes. Possibly, the resulting mix could still satisfy the specified requirements. If so, the available aggregates could be used economically, without compromising on the quality of mixes. This would result in aggregate sustainability. With this objective, two types of bituminous mixes namely SDBC and BC were prepared at midpoint gradation of the specified ranges, as per MoRTH gradation tables and subsequently by combining the above two gradations taking average of the two midpoint gradations. The Marshall mix properties were compared and found that the mix requirements are largely satisfied at the combined gradation as well. Keywords: Aggregate, sustainability, bituminous mixes, midpoint gradation, combined gradation
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IMPACT OF AL-COMPOSITES IN THE MANUFACTURING INDUSTRY: A NECCESSITYIAEME Publication
In the engineering sector today, the need to substitute for orthodox materials like
wood, aluminium, steel and concrete, has led to the invention of raw materials that
meet specific needs like hardiness-to-mass ratio, i.e. increased strength and light
weight, increased strength of impact, dimensional constancy and resistance to
corrosion. These materials are called composites. In this paper, we have assessed
several articles by a number of researchers on the impact of composites in the
manufacturing industry, making aluminium composites our focus. This review studied
the properties, behaviours, applications, advantages and setbacks, of aluminium
composites. From this study, it was observed that the automotive industry makes the
most use of aluminium composites, for the manufacture of parts like pistons and
connecting rods. However, processing of Al-dependent MMC’s is costlier than other
raw materials. And this is a major setback in the use of aluminium composites in the
manufacturing industry
IMPACT OF AL-COMPOSITES IN THE MANUFACTURING INDUSTRY: A NECCESSITYIAEME Publication
In the engineering sector today, the need to substitute for orthodox materials like wood, aluminium, steel and concrete, has led to the invention of raw materials that meet specific needs like hardiness-to-mass ratio, i.e. increased strength and light weight, increased strength of impact, dimensional constancy and resistance to corrosion. These materials are called composites. In this paper, we have assessed several articles by a number of researchers on the impact of composites in the manufacturing industry, making aluminium composites our focus. This review studied the properties, behaviours, applications, advantages and setbacks, of aluminium composites. From this study, it was observed that the automotive industry makes the most use of aluminium composites, for the manufacture of parts like pistons and connecting rods. However, processing of Al-dependent MMC’s is costlier than other raw materials. And this is a major setback in the use of aluminium composites in the manufacturing industry.
International Journal of Engineering and Science Invention (IJESI) is an international journal intended for professionals and researchers in all fields of computer science and electronics. IJESI publishes research articles and reviews within the whole field Engineering Science and Technology, new teaching methods, assessment, validation and the impact of new technologies and it will continue to provide information on the latest trends and developments in this ever-expanding subject. The publications of papers are selected through double peer reviewed to ensure originality, relevance, and readability. The articles published in our journal can be accessed online.
MANUFACTURING AND FORCE DETERMINATION OF COMPOSITE DISC BRAKEIAEME Publication
This paper deals with design and analysis of disc brake rotor using composite material. Thecomposite material used is Aluminum Metallic Medium Composite it is a the combination of
aluminum and silicon carbide length ways With a small percentage of other materials likemagnesium, aluminum oxide, graphite .These additional materials are added in accurate quantity
to increase the chemical, mechanical and thermal properties ofmaterial. The manufacturing
process is carried ready in organized location. Magnitude die casting process is used tomanufacture the disc brake using the composite material. In this paper the composite disc brakeismodeled in CATIA .The forces acting on the disc brake model are calculated using ADAMSsoftware.
Analysis of Mechanical and Metallurgical properties of Al-SiCp Composite by S...IJRES Journal
Composites are one of the recent trends of interest in present material innovations. Mostly metal matrix composites (MMCs) have found its applications in aerospace and automobile industries. This is because of its highly attractive properties like low density, high strength, high temperature resistance, higher strength to weight ratio. Even though it has superior properties it faces several hurdles like high cost of production, poor dispersion of reinforcement material on the matrix. A study has been made to solve this problem by forming a metal matrix composite which has Aluminium (Al-97.47% C.P) has been the matrix material and Silicon Carbide (SiC- 31.5-32μm) been a reinforcement material. A new technique, Squeeze-Cum-Stir Casting, a method used to solve the problems faced in today‘s MMC production process. The experiments have been made by varying the volume fraction of SiC (5%, 15%, and 25%), while keeping all other parameters constant. Parameters like hardness, impact strength, and ultimate tensile strength were analyzed and observed and Scanning Electron Microscopy (SEM) analysis was performed.
ANALYSIS OF MECHANICAL AND MICRO STRUCTURAL BEHAVIOUR OF AL BASED METAL MATRI...IAEME Publication
In recent years Metal matrix composites have been considered as one of the most important materials which offer excellent wear resistance and stiffness, low weight, economic and high
strength to weight ratio. Metal matrix composites (MMCs) reinforced with ball milled nano particles ,also called metal matrix –nano composite, are spreading rapidly in worldwide due to their various demands in the field of engineering and science like automobiles, aerospace, energy, defence,materials, electronics and bio technology.
Experimental evaluations and performance of the aluminum silicon carbide par...IAEME Publication
Stresses induced due to thermal mismatch between the metal matrix and the ceramic reinforcement in metal matrix composite may impart plastic deformation to the matrix there by
resulting in a reduction of the residual stresses. Thermal mismatch strains also may quite often crack
the matrix resulting in a relaxation of the residual stresses. The interface in MMCs is a porous, noncrystalline portion in comparison with the matrix or the reinforcement (metal matrix and ceramic reinforcement in this case).
A Overview on Effect of Reinforcement and Process Parameters on Properties of...IJRES Journal
Aluminum alloys are widely used in aerospace and automobile industries due totheir low density and good mechanical properties,bettercorrosionresistanceandwear resistance,lowthermalcoefficientof expansion as comparedto conventionalmetals and alloys. Theexcellent mechanicalpropertiesofthesematerialsandrelativelylowproductioncostmakethema very attractive candidate for a variety of applications both from scientific and technological viewpoints. Inthispaperanattempt hasbeenmadetoprovide a literaturereviewon theoverallperformanceofreinforcedcompositesfabricatedbystircasting method and effect of process parameters on properties of Aluminium based MMC.Theliteraturereviewframework inthispaper providesa clearoverviewthat the process parameters play important role for optimum properties of Aluminium based Metal Matrix Composites.
Neuro-symbolic is not enough, we need neuro-*semantic*Frank van Harmelen
Neuro-symbolic (NeSy) AI is on the rise. However, simply machine learning on just any symbolic structure is not sufficient to really harvest the gains of NeSy. These will only be gained when the symbolic structures have an actual semantics. I give an operational definition of semantics as “predictable inference”.
All of this illustrated with link prediction over knowledge graphs, but the argument is general.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Accelerate your Kubernetes clusters with Varnish CachingThijs Feryn
A presentation about the usage and availability of Varnish on Kubernetes. This talk explores the capabilities of Varnish caching and shows how to use the Varnish Helm chart to deploy it to Kubernetes.
This presentation was delivered at K8SUG Singapore. See https://feryn.eu/presentations/accelerate-your-kubernetes-clusters-with-varnish-caching-k8sug-singapore-28-2024 for more details.
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
Slack (or Teams) Automation for Bonterra Impact Management (fka Social Soluti...Jeffrey Haguewood
Sidekick Solutions uses Bonterra Impact Management (fka Social Solutions Apricot) and automation solutions to integrate data for business workflows.
We believe integration and automation are essential to user experience and the promise of efficient work through technology. Automation is the critical ingredient to realizing that full vision. We develop integration products and services for Bonterra Case Management software to support the deployment of automations for a variety of use cases.
This video focuses on the notifications, alerts, and approval requests using Slack for Bonterra Impact Management. The solutions covered in this webinar can also be deployed for Microsoft Teams.
Interested in deploying notification automations for Bonterra Impact Management? Contact us at sales@sidekicksolutionsllc.com to discuss next steps.
GDG Cloud Southlake #33: Boule & Rebala: Effective AppSec in SDLC using Deplo...James Anderson
Effective Application Security in Software Delivery lifecycle using Deployment Firewall and DBOM
The modern software delivery process (or the CI/CD process) includes many tools, distributed teams, open-source code, and cloud platforms. Constant focus on speed to release software to market, along with the traditional slow and manual security checks has caused gaps in continuous security as an important piece in the software supply chain. Today organizations feel more susceptible to external and internal cyber threats due to the vast attack surface in their applications supply chain and the lack of end-to-end governance and risk management.
The software team must secure its software delivery process to avoid vulnerability and security breaches. This needs to be achieved with existing tool chains and without extensive rework of the delivery processes. This talk will present strategies and techniques for providing visibility into the true risk of the existing vulnerabilities, preventing the introduction of security issues in the software, resolving vulnerabilities in production environments quickly, and capturing the deployment bill of materials (DBOM).
Speakers:
Bob Boule
Robert Boule is a technology enthusiast with PASSION for technology and making things work along with a knack for helping others understand how things work. He comes with around 20 years of solution engineering experience in application security, software continuous delivery, and SaaS platforms. He is known for his dynamic presentations in CI/CD and application security integrated in software delivery lifecycle.
Gopinath Rebala
Gopinath Rebala is the CTO of OpsMx, where he has overall responsibility for the machine learning and data processing architectures for Secure Software Delivery. Gopi also has a strong connection with our customers, leading design and architecture for strategic implementations. Gopi is a frequent speaker and well-known leader in continuous delivery and integrating security into software delivery.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Knowledge engineering: from people to machines and back
D012642240
1. IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE)
e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 6 Ver. IV (Nov. - Dec. 2015), PP 22-40
www.iosrjournals.org
DOI: 10.9790/1684-12642240 www.iosrjournals.org 22 | Page
Review of Effective Parameters of Stir Casting Process on
Metallurgical Properties of Ceramics Particulate Al Composites
Khalid Almadhoni*, Sabah Khan**
*(Ph. D. Student, Department of Mechanical Engineering, Faculty of Engineering and Technology, JMI, Jamia
Nagar, New Delhi-110025 (India),
**(Dr. Assistant Prof., Department of Mechanical Engineering, Faculty of Engineering and Technology, JMI,
Jamia Nagar, New Delhi-110025 (India),
Abstract: The low density, environment resistance and adequate mechanical and physical properties of
aluminium metal matrix composites (AMMC’s) make them one of the most interesting material alternatives for
the manufacture of lightweight parts for many types of modern engineering equipments. Fabrication of
aluminum and it’s alloys based casting composite materials via stir casting is one of the prominent and
economical technique for development and processing of metal matrix composites materials. The major
challenges of this technique are to achieve sufficient wetting of particles by liquid metal, to get ahomogeneous
dispersion of ceramic particles and to reduce porosity in the cast metal matrix composite.This article is just a
review of stir casting for production of aluminum metal matrix composites, various process parameters of stir
casting process, such as stirrer design, stirrer speed, stirring temperature, stirring time (holding time), preheat
temperature of reinforcement, preheated temperature of mould, reinforcement feed rate, wettability-promoting
agent and pouring of melt, and difficulties encountered in successful fabrication of AMMC’s via stir casting
technique. There were various articles accessed, however not all were completely relevant and as a result not
included in this review.
Keywords:Aluminum metal matrix composites, Ceramic reinforcements, Stir casting process.
I. Introduction
The importance of the use of aluminum metal matrix composites (AMMCs) reinforced with ceramic
particles in modern engineering applications lies in the combined and unique characteristics that distinguish
them from the rest of the engineering materials, such as light weight, environment resistance and adequate
mechanical and physical properties [1]. Various techniques are used for manufacturing of MMC’s, they can be
classified into two main groups:
I. Liquid state processes, such as casting, melt stirring and in-situ and infiltration.
II. Solid state processes, such aspowder metallurgy, diffusion bonding and physical vapour deposition.
Melt stirring method has a good potential in all-purpose applications as it is a low cost MMCs
production method [2-3]. Stir casting is a liquid state method of composite materials fabrication, in which a
dispersedphase (ceramic particles, short fibers) is mixed with a molten matrix metal by means of mechanical
stirring. The liquid composite material is then cast by conventional casting methods and may also be processed
by conventional Metal forming technologies [4]. In preparing metal matrix composites by stir casting process,
some of the factors that need considerable attention, which are [5]:
To achieve uniform distribution of the reinforcement material.
To obtain sufficient wettability between the two main substances.
To reduce porosity in the cast metal matrix composite.
Various process parameters of stir casting should be properly controlled to obtain good metallurgical properties
of AMMC’s [6-7]:
1. Stirrer design.
2. Stirrer speed.
3. Stirring temperature.
4. Stirring time (Holding time).
5. Preheat temperature of reinforcement.
6. Preheated Temperature of Mould.
7. Reinforcement Feed Rate.
8. Wettability-promoting agent.
9. Pouring of melt.
The simplest and economical technique to fabricate MMC’s is simply mixing the solid reinforcement
in the liquid metal and then allowing the mixture to solidify in a suitable mold. The mixture can be continuously
agitated while the reinforcement is progressively added. In principle, this can be performed using conventional
2. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 23 | Page
processing equipment on a continuous or semicontinuous basis. Though the technique seems simple, there are
difficulties in this technique. Some of the problems are increased viscosity because of addition of reinforcement,
inhomogeneous microstructure and adverse chemical reactions.Commonly particulate reinforcements are used
in this technique due to the difficulty in casting with fibrous forms. A mixture of particles and molten matrix
material is cast into ingots and a secondary mechanical process, such as extrusion or rolling is commonly
applied to the composite to remove casting defects. Casting of MMCs needs some modifications to the existing
casting technique, which are [8]:
- The viscosity should be kept within the allowed limit.
- Alloys with minimum reactivity to the reinforcement must be used.
- Covering the melt with an inert gas atmosphere to reduce the oxidation.
- Stirring of the melt to minimize the settling of particles due to density difference.
The stirring action should be slow to prevent the formation of vortex at the surface of the melt, and care
must be taken not to break the surface too often, which could contaminate the bath with dross. Use of a slowly
rotating, propeller like mechanical stirrer is preferred by some foundries. In fact, results of laboratory studies
indicate that the mechanical property of the casting are maximized by continuous stirring versus intermittent
(hand) stirring. When induction melting, the furnace’s natural eddy current stirring action usually is sufficient to
disperse the particles, although supplementary hand stirring (with the power off) also is recommended to ensure
that no particles have congregated in potential “dead” zones [9].
II. Metal Matrix Composites
There are several perspectives used for classification of engineering materials, but the most common
perspective stipulates that the engineering materialsare classified into the following broad groups: metals,
ceramics, polymers and various types of composites of these.
Fig. 2.1: Classification of engineering materials [10]
Composites are two or more chemically discrete materials (constituents) which when combined have
enhanced properties over the individual constituents. One of the constituents is called the reinforcing phase, is in
the form of fibers, sheets, or particles, and is embedded in the other constituent called the matrix (continuous
phase). These type of materials could be natural or synthetic. Composite materials are classifiedby matrix into
metal matrix composites (MMC’s), ceramic matrix composites (CMC”s) and polymer matrix composites
(PMC”s), They can also be classified by filler type into particle reinforced composites,fiber reinforced
composites andstructural composites.
Fig. 2:2: classification scheme for the types of composites[11]
The fabricationtechnique used to synthesis a composite structure is dependent upon material
performance requirements, structure configuration, and production rates [12].A metal matrix composite (MMC)
3. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 24 | Page
is generally designated simply by at least twoconstituent parts, one being a metal necessarily and is called
matrix, the other material may be a different metal or another material, such as a ceramic or organic compound
and called reinforcement.MMC’s differ from other composites in several ways. Some of these general
distinctions are:
1. The matrix phase of MMC is either a pure or alloy metal.
2. MMCs exhibitlower ductility and toughness than their respective unreinforced metal matrix alloys, but they
have higher ductility and toughness than CMCs.
3. The role of the reinforcement in MMCs is to increase strength and modulus.
4. MMCs are characterized by a temperature capability higher than polymers and polymer composites but less
than ceramics and ceramic composites.
5. Low to moderately reinforced MMCs can be formed by processes normally associated with
unreinforcedmetals.Generally, properties of produced metal matrix composites reinforced with ceramic particles
depend on the properties of ceramic reinforcements such as type, size, geometry and distribution of
reinforcements, also the reinforcement volume ratio (RVR) [13-14].
Fig. 2.3: Schematic presentation of three shapes of metal matrix composite materials [15]
2.1. Aluminium metal matrix composites (AMMC’s)
Different kinds of composite materials can bemanufactured via different techniques. Metal matrix
composite (MMC’s) is one of these kinds. Aluminum and its alloys are the most commonly used matrix
materials in the production of MMC’s because of their preferred advantages. The major advantages of AMMCs
compared to unreinforced materials include: high strength, good stiffness, low density (weight), controlled
thermal expansion coefficient, thermal/heat management, enhanced and tailored electrical performance,
improved abrasion and wear resistance, control of mass (especially in reciprocating applications), good
environmental resistance and improved damping capabilities. The combination of these properties have made
aluminum and its alloys to be the most commonly used matrix materials in the production of (AMMCs), thus to
make them the more popular composites. Furthermore, aluminum is characterized by high melting point high
enough to satisfy many application requirements [1-16].
2.1.1. AMMC’s reinforced with ceramic particles
Different types of ceramics such as SiC, CuO, Fe2O3, Fe3O4 SiO2, Al2O3, MgO, ZnO, BeO, MnO2,
TiO2, TiC, etc. can be used as reinforcing phases and embedded in the metal matrix to fabricate MMC’s.
Ceramics are characterized by superior properties such as refractoriness, high compressive strength and
hardness, excellent wear resistance, etc. These properties make them appropriate for use as reinforcement in
MMCs [17-18-19].
III. Stir Casting Technique To Fabricate AMMC’s
Stir Casting method is a liquid metallurgy technique in which the second phase materials
(reinforcements) are introduced into the molten matrix and allowing the mixture to solidify. Here, the critical
thing is to create good wetting between the reinforcements and the moltenaluminium or aluminium alloy, this is
the simplest and most commercially used technique and known as vortex technique or stir-casting technique.
The vortex technique involves. To reduce gravitational segregation in the crucible, the vortex technique is
developed to involve the introduction of pre-treated ceramic particles into the vortex of molten aluminium alloy
created by the rotating impeller [1-20].
4. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 25 | Page
Fig. 3.1: Conventional stir-casting setup for the compositing of aluminum MMC material. This is the most
common commercial method. [21]
In case of some molten metal like aluminum, inert gas such as nitrogen and argon can also be used to
remove hydrogen, this method involvesintroducing bubbled inert gas into the liquid aluminum. The hydrogen is
drawn to the inert gas bubbles, then carried up through the aluminum and released on the surface. In recent
development, the composite is stirred while the molds are filled by pouring the melt through the bottom of the
crucible [20].
Fig. 3.2: Stir casting machine (equipped with inert gas source and pour molten system[22]
Choose theappropriatemethod and material are the most important and effective criterion toproduce
MMCs. In case of MMC’s manufacturing via melt stirring technique, increased reinforcement volume ratio
(RVR) and decreased particle size resulted more difficult production process and increased porosity and particle
agglomeration.This technique is attractivebecause of simplicity, flexibility and most economical for largesized
components to be fabricated [23-24].
IV. Investigative Review On Ceramic Particulate Al Composites Fabricated
Using Stir Casting
Aluminum LM25 as matrix material and silicon carbide (SiC) with various RVR as reinforcement
material were selected to fabricate aluminum metal composites using stir casting method. SiC particles were
preheated up to 800 o
C and added to the Al matrix in semi-solid state.
5. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 26 | Page
Stir Casting Apparatus
The results showed that the stir casting technique can be considered as an effective liquid based
technique for making the aluminium metal matrix composites [25].
AMMCs using AA 356 alloy as matrix andmilled alpha alumina as reinforcement are manufactured via
stir casting method. A combined route of stirring at semi-solid state followed by stirring at liquid state was
proposed to conduct a quantitative analysis of the mechanical stir casting . The effect and interactions of factors,
such as time, rotation, initial fraction and particle size on the incorporated fraction were investigated. Other
factors, such as matrix and reinforcement composition, crucible and propeller blade geometry, reinforcement
treatment and mould material, were kept constant. It was found that the best incorporations were obtained with
all factors at high levels and the time factor does not show any significant influence on the incorporation
process. The particle size and rotation are the factors of greater influence. Particle wetting occurs during stirring
at semisolid state because of interactions among the particles themselves, between particles and solid aluminium
and between particles and the remaining liquid phase. Addition of Mg as a wettability-promoting agent
enhanced the wettability between the particles and aluminum [26].
A. Mazahery and M. Shabani studied the microstructure of nano composites based on the A356
aluminum alloy reinforced with nanoSiC particles fabricated via stir casting. The results showed that the nano-
sized SiC particles are successfully incorporated into the aluminum matrix and the composites contain little
porosity and the amount of porosity increases with increasing volume fraction of SiC which can be attributed to
the increased surface area of the nanoSiC particles. It was also observed a reasonably uniform distribution of
SiCnano particles in the Al matrix. [27].
M. Prakash and M.Jaswin used SiC and B4Cparticles as reinforcements and Al6061 as matrix to
produce a composites by stir casting process. The composites were producedby varying the particulate addition
by weight fraction of Al (90%), SiC (5%, 6.5% and 8%) and B4C(5%, 3.5% and 2%). Al rods were preheated at
850 o
C for 3 to 4 hours before melting and mixing the SiC and B4C particles were preheated at 840 o
C for 1 to 3
hours to make their surfaces oxidized. The furnace temperature was first raised above the liquids to melt the Al
alloy completely and was then cooled down just below the liquidus to keep the slurry ina semisolid state.Manual
mixingwas used because it was very difficult to mix using automatic device when the alloy was in a semisolid
state. Aftersufficient manual mixing was done, the composite slurry was reheated to a fully liquid state and then
automaticmechanical mixing was carried out for about 10 minutes at a normal stirring rate of 600 rpm.
6. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 27 | Page
Experimental setup used for stir casting
Results showed that the dispersion of theSiC and B4C particles are equal in all over the composites and
also shown in the images. It was noted that an increase the particles cluster corresponding to an increase in the
processing temperatures [28].
AMMCs were developed using AL6063 as matrix material and SiC particles with various RVR
(between 10% and 50% at 10% intervals) as reinforcement. Composites were produced using stir casting
technique and the homogeneous mixture obtained cast into cylindrical blanks. The results indicated that the
produced composites possess superior metallurgical properties. It was also found that an increase in the quantity
of SiC reinforcement positively effects on the metallurgical properties only up to a 40%wt SiC beyond this,
increased clustering of the reinforcements [29].
A conventional low cost technique (Stir casting) was developed to produce aluminum based silicon
carbide particulate Metal Matrix Composites (MMCs) type (Al+4%Cu+5%SiC) were fabricated with
homogenous dispersion of ceramic material. The balanced aluminium with 4% Cu was meltedin a graphite
crucible in an open hearth furnace. Al-4%Cu alloys where preheated at 450o
C for 3 hours and the SiC
particleswere preheated at 1100°C for 2 hours.After stirring for 3 minutes at 600 rpm, composites were poured
with pouring temperature 700 o
C, 725 o
C and 750 o
C respectively.
Schematic View of Experimental Set Up
Results indicated that Al-4%Cu alloy reinforced with 5% SiC composites were prepared successfully
via liquid metallurgy technique ( stir casting). It was found that the pouring temperature at 725°C which gave
the bestoptimum value of hardness, impact strength and ultimatetensile strength. When the pouring rate kept
constant at 2.5cm/s for all composites [30].
Aluminum alloy (Al-11Si-Mg) matrix composites reinforced with silicon carbide (SiC) particles with
average size of 40 μm were fabricated by different processing temperatures with different holding time to
evaluate the effect of process parameters on the distribution of particle in the matrix. The matrix was melted in a
graphite crucible at different temperature level (700°C, 750°C, 800°C, 850°C and 900°C). The
7. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 28 | Page
SiCreinforcement was preheated at 1000°C for two hours before added in the matrix melt. The 10% by volume
of preheated SiC powder was added in the liquid melt and the slurry was consciously stirred using a stirring.
The four blade stirrer was designed in order to produce the adequate homogenous particle distribution
throughout the matrix material.
Stirrer blade setup
Results showed that the particles were distributed uniformly in the processing temperature 750°C and
800°C. Particles agglomerations were found in the processing temperature of 700°C, 850°C and 900°C because
of the changes of viscosity in liquid Al matrix.The viscosity of Al matrix decreases with increased processing
temperatures. It is revealed that holding time influences the viscosity of liquid metal, particles distribution and
also induces some chemical reaction between matrix and reinforcement.The hardness values increases more or
less linearly with increasing of processing temperatures from 750°C to 800°C at 20 minutes holding time [31].
L.Saravanan and T. Senthilvelan fabricated aluminum composite with nano‐ Al2O3 using a three
stepmixing stir casting process. Its dispersion was investigated andcompared with the characteristics of
thenano‐composite fabricated usingconventional method as well as the basematrix alloy. The three step mixing
method includes the following:
1. Heat treatment of reinforcement particles at 1100 o
C for 10 minutes in an inert atmosphere.
2. Injection of heat‐treated particles within the melt by inert argon gas.
3. Stirring of the melt 10 minutes before and after incorporation of particles at the speed of 300 rpm.
Experimental setup used for thefabrication of nanocomposite
The results showed homogeneousdistribution of the nanoparticles inthe case of the three step
mixingmethod, whereas poor incorporationof the particles and particle clusteringwere observed in the case of
nanocomposite fabricated usingconventional stir casting method [32].
Aluminium siliconcarbide mica a hybrid metal matrix composite was manufactured by stir casting
method. Three different compositions were taken with various percentage of mica as 1%, 2% and 3%. Al 6061
was used as matrix, it was melted at a temperature of 850°C. The required quantity of reinforcement materials
were weighed and kept inside the furnace, in order toincrease the intermolecular bonding with Al.The dies were
preheated to a temperature of 500°C. 1% Pure Mg powder was added to the molten metal to compensate for the
loss during heating and also toincrease the wettability. Degasser powder was added to remove the impurities in
the molten metal and coverall was sprinkled over the Al to prevent oxidization.The reinforcement materials
8. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 29 | Page
were added with the molten Aland were manually stirred.It is then again kept inside the furnace to obtain a
temperature of 850°C. Stirrer was introduced inside the furnace which rotates at 300 rpm. The stirring was done
keeping the temperature constant and was carried out for approximately 10minutes.Then the molten metal
matrix composite obtained was poured into preheated die and was set to cool off for threehours. This procedure
was repeated for the 3 different compositionsand the specimens required for the vibration analysis are thus
obtained.
stir casting equipment
It is observed that the AMMCs can be fabricated using stir casting technique. SEM photos revealed that
the reinforcements were uniformly distributed in all the three compositions [33].
Aluminum cast Alloy (6063) as matrix and alumina (Al2O3) powder with various volume ratio as
reinforcement were used to producemetal matrix composite by the stir casting technique.
Stir Casting
Aluminum Alloy 6061 was melted in acrucible by heating it in a muffle furnace at 800°Cfor three to
four hours. Al2O3particles were preheated at 1000 ºC and 900 o
C respectively for oneto three hours. The
temperature was first raised about 750 o
C, above the liquidus temperature of aluminum alloy, to melt it
completely and was then cooleddown just below the liquidus to keep the slurry insemi solid state. Stirrer was
carried out for about 10minutes at stirring rate of 290 RPM. At this stage,the preheated Alumina particles were
addedmanually to the vortex. In the final mixing processesthe furnace temperature was controlled within 700
±10ºC. After stirring process the mixture was pour inthe other mould to get desired shape of specimen. Results
showed that aluminum matrix composites were successfully fabricated by stir casting process with fairly
uniform distribution of alumina particles [34].
R. Adat, S. Kulkarni and S. Kulkarni manufactured a metal matrix composite by reinforcing alloy
Al356 with Al2O3 and fly ash particles with difference RVR (2,4 and 6% each) using stir casting process. After
cleaning A356 alloy ingots, they were cut to proper sizes, weighed in requisite quantities and charged into a cast
iron crucible placed in the furnace at 400 o
C.1% pure Mg was added into the charge at 600 o
C after confirming
the semisolid state to improve wettability. Then material was hold for about an hour until its temperature gain
9. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 30 | Page
reached 800 o
C. The scum powder (0.05% of Al356) was added into the melt which resulted into accumulation
of impurities at the surface of liquid melt. Then the scum was removed. Degasification tables of
Hexachloroethane (0.05% of Al356) were added for removal of gases from the molten alloy.The combination of
reinforcement was preheated to 300 o
C – 400 o
C for 1 hour before pouring in to the melt of Al356. Al2O3 were
poured centrally into the vortex at 0.5 g/s feed rate.
Stir Casting Setup (Schematic)Stirring processStirrer Blades
The stirrer was moved down slowly, from top to bottom by maintaining a sufficient clearance from the
bottom. The stirrer was then pushed back slowly to its initial position. The pouring temperature of the liquid was
kept around 800 o
C. Liquid Composite was poured in the MS permanent mould with uniform pouring rate,
keeping pouring distance constant, to maintain the fluidity of melt. Mould also was preheated at 300 o
C – 400 o
C
for 1 hour. Results showed that AMMCs were successfully manufactured by stir casting technique with fairly
uniform distribution of fly ash and Al2O3 particles.Stir casting is very efficient, simple and cost effective method
of manufacturing of AMMCs and also it is most suitable for mass production. Processing parameters such as
holding temperature, stirring speed and time, blade design of the stirrer and preheating process are among the
important factors to be considered in the production of cast AMMCs as these have an impact on quality and
properties of casting.It was observed that preheating the mould improves the soundness of the casting, shown by
a decrease in the porosity level. The wettability between matrix and reinforcement was improved by addition of
Mg in melt.The fabricated AMMC is isotropic in nature due to fairly uniform distribution of
reinforcement [35].
LM 26 Al, rice husk ash and red mud (LM 26 Al/RHA/RM) hybrid composites were prepared via stir
casting. Taguchi’s L9 orthogonal array was used for experimental design. Overall performance of the stir
casting method was improved significantly by combining the experimental and analytical concepts and the most
important parameter was determined on the result response. Threedifferent parameters, stirring time, stirring
speed, and weightfraction of the reinforcement particles were used for optimization of the tensile strength and
hardness. Red mud was maintained constant at 5wt% and rice husk ash was varied at 5, 10 and 15 wt% for
fabricated the composites. LM 26 aluminium alloy was taken into agraphite crucible and melted. RHA and RM
powder was preheated at1500o
C for 20 minutes and then added to the melt. The melt was stirred inside the
furnace at different speed andtimes to make a vortex in order to disperse the particles. The melt temperature was
controlled around 7000o
C and poured into steel die.
Stir casting equipment
10. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 31 | Page
The results showed that the hybrid composites prepared with 15% weight fraction particles, 12 minutes
stirring time and 100 rpm stirring speed have optimum good tensile strength, hybrid composites prepared with
15% weight fraction particles, 12 minutes stirring time and 200 rpm stirring speed have optimum level of
hardness. It can be concluded that Taguchi method has proved its success in prediction the optimum casting
parameters to reach the best properties [36].
Pure Al as matrix material and Al2O3as reinforcement were used for the preparation ofcomposite by
stircasting route. Particle sizes of Al2O3 (75, 105 and 150 micron), wt. % of reinforcement (3%, 6% and 9%) and
stirring time (15, 20 and 25 minute) were used to fabricate different sample of AMMCs. Each parameter has
three different levels. L9 orthogonal array table used to made different specimen. The effect of these input
process parameter on the output response were analyzed using analysis of variance (ANOVA). The contribution
of each process parameters on the hardness, impact strength and tensile strength was analyzed by using
ANOVA. Al was melted at 800 o
C, Al2O3 was preheated at 300 o
C for 1 hr. The temperature was cooled down
just below the liquidustemperature near about 700ºC to form the slurry in the semisolid state. The stirrer also
placed in the furnacefor preheating purpose. Now the molten Al was stirred for 10 minutes at stirring rateof 300
RPM. Preheated alumina particles were embedded inthe molten by three steps mixing of melt. At every
stagebefore and after introduction of reinforcement, mechanicalstirring is carried out for a period of 5 min.
Similarly remainedreinforcement particles were added. In the final mixingprocess the furnace temperature were
controlled within700±10ºC. The stirrer position was such that 35% of materialshould be below the stirrer and
65% of material should be above the stirrer. After the complete addition of particles,the melt was stirred for a
defined time. The melt was poured inthe preheated mould (300ºC) to get a desired shape ofcomposite. The
mixture was allowed to solidify for a desiredtime.
Stir casting setup
Results indicated that all composites were successfullysynthesized by stir casting technique.It was
revealed that the hardness of composite increased with increasing the weight percentageof Al2O3 particles,
stirring time but decrease withincrease in particle size.The tensile strength of the manufactured compositewas
higher in composite. Impact strength was higher in case of composites ascompared to the pure Al.The Signal-to-
noise ratio showed the effect of eachparameter at each level on the hardness, impactstrength and tensile strength
of composite.Analysis of variance determined the contribution ofeach parameter in the hardness, impact strength
andtensile strength of the prepared composite.All these mechanical properties showed increasing trend with
increase in wt.%, stirring time anddecrease in particle size of the reinforcement [37].
Manufacturing of composite material by reinforcing Al alloy as matrix and SiC, Al2O3 and graphite
particles using stir casting process was studied. The fabricated composite was tested for its mechanical,
metallurgical andtribological properties. At first heatertemperature is set to 500°C and then it is gradually
increased up to 900°C. Aluminium alloy was cleaned, weighed and then kept in the cruciblefor
melting. Nitrogen gas was used as inert gas to avoidoxidation. 4 blades were welded to the shaft at 45°C.. Pure
Mg powder was used 1% by weightas wetting agent. Required quantities of reinforcementpowder and
magnesium powder were weighed thoroughlymixed for 24 hour.Reinforcements were preheated for 1/2 hour
and attemperature of 500°C. When matrix was in the fullymolten condition, stirring is started after 2 minutes.
Stirrerrpm was started at slow rate of 30 rpm and increasesslowly in between 300 to 600 rpm with speed
controller. Temperature of the heater is set to640°C which is below the melting temperature of thematrix. A
uniform semisolid stage of the molten matrixwas achieved by stirring it at 640°C. Preheatedreinforcements were
11. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 32 | Page
poured at the semisolid stage. Reinforcement particles were fed in constant rate to avoid coagulation and
segregation of the particles.The flow rate of reinforcements measured was 0.5 g/s. Dispersion time was taken as
5minutes. After stirring 5 minutes at semisolid stage slurrywas reheated and hold at a temperature 900°C to
make sure slurry was fully liquid. Composite slurrywas poured in the metallic mould, which was preheated at
temperature500°C.
Stir cast apparatus
Results included that for uniform dispersion of material blade angle shouldbe 45° or 60 ° and number
of blade should be 4.For good wettability, operatingtemperature should be kept at semisolid stage i.e. 630 for Al
(6061). Atfull liquid condition it was difficult uniform distributionof the reinforcement in the molten metal.
Porosity was reduced by preheating of mould [38].
LM25 aluminum alloy reinforced with micro and nano-sized 10 wt.% Al2O3 was successfully produced
via stir casting method.LM25 Al alloy was charged into the crucible and heated to 750 o
C. The mixer was
lowered into the melt slowly to stir the molten metal. The micro and Nano Al2O3 particles were preheated before
being mixed with the Al alloy melt. After the completion of particle feeding, the mixing was continued for a
further 7 min. The molten mixture was poured in the preheated mold positioned below the furnace. The furnace
had a provision for bottom tapping and this permitted heating as well as stirring to be continued even during
tapping of the melt.
Stir casting furnace setup
12. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 33 | Page
The results revealed that stir casting could be an economical route for the production of nano
composites. Scanning electron microscopic observations of the microstructures revealed that the dispersion of
the micron size particles where more uniform while nanoparticles led to agglomeration of the particles.By
proper optimization of the process parameters, stir casting can be a promising and economically viable route for
the production of nano particle reinforced MMCs [23].
Al-MgO reinforced metal matrix composites (MMCs) of 5%, 10% and 15% RVR were produced by
melt stirring. EN AW 1050A aluminum alloy as the matrix and MgO powders with particle size of –105 μm
were used as the reinforcement were used to produce the composites. Matrix material Al was put in the crucible,
melting process was started and continued until the temperature of liquid matrix increased to 750 °C. Stirring
apparatus was immersed in liquid metal and stirring was started. Stirring speed was gradually increased until
500 rev/min and MgO powder determined on the basis of RVR was added in liquid metal by a funnel during
stirring process. After the addition of reinforcement element MgO in liquid matrix Al, the mixture was stirred
about 4 minutes at 500 rev/min in order to allow homogenous distribution of MgO particles in the mixture.
Subsequent to the completion of stirring, the crucible was taken out of the furnace, the liquid melt was poured in
steel containers.
Melt stirring test apparatus (For the production of composite specimens
Results showed that in the MMCs production by the melt stirring technique, theMgO with the particle
size of –105 μm was homogeneouslydistributed inside the liquid Al at all RVR. It was noted a little difficulty in
wetting because of increasingthe amount of MgO reinforcement in liquid matrix.It can be stated that 750 °C
liquid Al temperature,500 rev/min, the mixing speed and mixing time of 4 minutes were sufficient in
experiments. However, to obtain morehomogeneous distribution of reinforcement within thematrix MgO and to
improve the wetting these values canbe increased.Depending on the increasing MgO reinforcement ratio,the
porosities increased in the composites [39].
Metal matrix composites containing analuminium alloy C355 as base material and 5 wt.%SiC as
reinforcement material were produced by stir casting method.
Aluminum alloy C355 was heated to above its liquidtemperature in muffle furnace. The
temperaturewas700°C to 790 °C. The 5 wt.% SiC particles withan average size of 50 micrometer were added on
the surface of the molten liquid before preheating. The SiC particledisperses into the melt material.
C355+5%SiC MMCstirred about 200 to 600 seconds and the stirring speed ofmelt material was 140 to 240 rpm.
Experimental setup of mechanical stir casting
13. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 34 | Page
Results revealed that the mechanical stir casting process was successfullyutilized for casting
(C355+5%SiC) matrix composites. It was found that the SiC particles are properly distributed withmatrix C355
[40].
S. Nair and N. Joshi fabricated aluminium matrix composite (AMC) using stir casting technique, where
Al 6061 was the base metal and 10 wt.% silicon carbide (SiC)in powder form with 320 mesh size was the
reinforcement material. Al 6061 was melted in a graphite crucible at around 650º C.Into the molten matrix, 10
wt.%SiC powder of 100 mesh size was added. 1% Magnesium powder wasalso added in order to improve the
wettability and decrease the porosity. Stirrer was made out of graphite rod of 100mm length and 25mm diameter
for stirring. Externalthreading was done on the stirrer . An internally threaded 3 feet long stainless steel rod was
fitted overthis stirrerThe mixture was mechanically stirred using a motor of around 250 RPM for 10 minutes
before pouring into themould.The AMC mixture was poured into the mould and allowed to solidify for some
time.
Graphite StirrerStirring of Al+ SiC mixture using motorPouring of molten Al into mould
Results indicated that the SEM micrographs show good distributionof SiC particles. The magnesium
powder on adding reduced the porosity and improved wettability. Stir castingmethod is the simplest and most
economical method to produce good quality aluminium metal matrix composites [41].
Aluminum-magnesium matrix composites reinforced with silicon carbide were produced using
modified stir casting technique. The usual solid shaft stirrer was replaced by a hollow spindle stirring
mechanism through the additions of particulate silicon carbide and magnesium turnings were introduced in
small cylindrical capsules
Aluminum were cut from Al-ingot and was melted in a cast iron cylindrical crucible at 800 o
C. Then
the capsule / bullet charged with pieces of Mg-chips or Silicon carbide particulates. The mixer was turned on
and set to the predetermined speed of 500 rpm. Then previously prepared silicon carbide particulate (10 wt %)
bullet charges were introduced one after the other into the Al-Mg alloy melt. Then crucible was lifted and the
melt waspoured into previously readied mould made of fire bricks joined by fire clay.
Perforated steel capsule welded to plunger rod
The results showed that the modified stir casting process can address some of the problems of
producing cast metal matrix composites. The method is suitable for eliminating the fading effect of inoculation
and simultaneous addition of alloying element and reinforcement. The process can be easily adopted for
production in industrial scale [42].
Al-base 2024 alloycomposites reinforced with SiC nanoparticles were fabricated using stir casting
method.
Two different master powders (pure Aland pure Cu powders with a mean size of 60μm, and each
containing 1wt.% SiCnano-powder with 50 nmparticles size)were produced by mechanical milling and used as a
reinforcement. Mechanical milling wasperformed for 1 h at the rotational speed of 900 RPM with steel balls
with 10 mmdiameter.Each charge consisted of 450 g commercial Al-2024 alloy inwhich 18 g of master powders
were added. These master powders were separatelyadded to the melt, and in two separate molds for each
composite. The temperature of the melt was 750ºC and the stirring process began at 512 RPM for 6 minutes. All
castingprocesses were held under inert atmosphere. Melt was poured to a cylindrical steel mold.
14. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 35 | Page
Schematic drawing of the utilized rheocaster device
Results revealed that Alcoated particles have higher wettability and better dispersion in the matrix
because of their lower melting point and also this dispersion induces particles to act asgrain refiner of the melt.
Hence, grains become finer. Furthermore, high nucleation rate inmelt which is result of great temperature
difference between powder and melt which produces a spherical and rosette-shaped grains, so this phenomena
can reduce theviscosity of melt during casting process [43].
AMMCs reinforced with AlN were produced using stir casting technique. Al-Si alloy and AlN with
purity of >98% and average size of <10 μmwere chosen as matrix and reinforcement material, respectively.
The metal matrix composites prepared contained 2, 5 and 10 wt% of AlN. The Al alloy was cleaned with
acetone in ultrasonic bath prior to melting, then heated in a graphite crucible under controlled argon
environment. Less than 0.5% Mg was added into the crucible which acted as wetting agent. A furnace heating
temperature was increased to 750ºC, hold for 30 minutes until Al alloy melted completely. Aluminum dross then
removed from the surface of the molten metal. Small amounts particulate aluminum nitride preheated to 750º
were added continuously to the molten metal through the side of vortex created by mechanical stirring by the
stir impeller.The impeller and stirring rod was coated with liquid alumina so as to avoid any metals
contamination to the molten metal. The optimum stirring speed was determined at 450 rpm. The composite melt
was stirred for 5 minutes then immediately cast into a permanent mould by bottom pour technique.
Schematic diagram experimental stir cast set-up
Results showed that a stir casting process which was set at 750ºC was successfully utilized for casting
Al-Si matrix composites reinforced with AlN particles. Lack of porosity exhibited in the microstructure of Al-Si
matrix composite indicates there is a rather good particulate-matrix interface bonding [44].
A. Anis, M. Nagarajan and N. Balaji developed the metal matrix composite Al-10%MoO3 by stir
casting method. They used MoO3 is used as reinforcement and aluminium (98.41%) as matrix. Aluminium
powder was heated at 900 o
C.This metal-matrix composite is then pouredinto the graphite crucible winded with
resistive heatingcoil at 760°C. 10% of reinforcement was added and stirred the composite byusing the stir
casting machine. The stirrer is exactly plus sign blade having zigzag angle 90° of each side. Automatic stirring
was carried out for 10 minutes with normal 400 rpm of stirring rate.
15. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 36 | Page
Experimental diagram
Results revealed that the prepared composite have the better properties than the purealuminium, this
suggests that the composite characterizes by good metallurgical properties [45].
A. Jailania and S. Tajuddin selected SiC particlereinforced aluminum alloy to produce metal matrix
composites (MMC) using different of parameters blade angle and stirring speed, also different composition of
SiC reinforcement. After the experimental settling up the aluminium alloy was heated in the induction furnace
until it melt, the impeller was set at the angle of 30° and the stirring speed was 50 rpm to mix the SiC
reinforcement. The SiC reinforced aluminum alloys is stirred for 15 to 20 minutes. Then the mixture is poured
into the mould to prepare some specimens.
Schematic diagram for stir casting technique used
The result of the experiment showed that the composite with 10 wt.% SiC at blade angle of 30o
andstirring speed of 100 rpm gave has metallurgical properties. Results revealed that during lower speed and
lower stir time particle clustering occurred in some places, and some places were identified without SiC
inclusion. It was found that by increasing the stirring speed and stirring time better homogeneous distribution of
SiC in the Al matrix. Better distributions of SiC were found at blade angle of 30o
, stirring speed of 100 rpm and
10% SiC [46].
A2218 Aluminum alloy reinforced with alumina (Al2O3) particles in size range < 53 microns was
selected to produce metal matrix composite. The composite was investigated to find out the effect of stirring
speed on retention of ceramic dispersions. The process parameters varied are speed of stirrerin steps 180, 250,
400 and 1400 rpm. Particle wt% is also varied as 10 and 20% respectively. The effect of stirring speedand
particle content on microstructure and mechanical properties of the composites. The alloy was placed in the
graphite crucible at superheatedtemperature of 750°C to 850°C in the electrical resistancefurnace until it melted
completely. When this molten alloy was achieved, the additive (Al2O3) was added in it after preheatingthem at
the temperature about 700°C.
16. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 37 | Page
Schematic representation of stir casting set-up
Results indicated that with the increase in stirring speed, the distributionof the particles in the matrix
became uniform andtheir segregation reduced. This may be due to the additional energy applied by the stirrer at
higherrpm [47].
The effect of stirring speed and pouring temperature on mechanical, microstructure and machining
properties of Al6061-Cu reinforced SiC MMC was investigated. The composite was fabricated using stir casting
technique.Billet of aluminium and copper were preheated at 450 o
C for 40 minutes before melting and the SiC
particles were preheated at 1100 o
C for 2 hours to make their surfaces oxidized. The furnace temperature was
first raised above the liquidus to melt the feed stock completely and was then cooled down just below the
liquidus to keep the slurry in a semi-solid state. At this stage the preheated SiC particles were added and mixed
manually. After sufficient manual mixing, the composite slurry was reheated to a fully liquid state and then
automatic mechanical mixing was carried out for about 10 minutes at five different stirring speed. In the final
mixing process, the furnace temperature was within 800 o
C and the composite slurry was poured in a sand
mould designed to get standard specimens.
Schematic view of Experimental setup and stirrer
Results showed that an increase in stirring speed increases the impact strengthand hardness of material
up to a certain limit after that theseproperties decrease drastically. It was observed from an SEM study that at
stirring speed400 rpm better homogeneity can be obtained compared to200 and 600 rpm [48].
K. Paul and M.Sijo investigated the effect of stirrer parameter on aluminium alloy (LM6) reinforced
SiC MMC produced by stir casting method. Aluminium was preheated for 3 to 4 hours at 450°C andsilicon
carbide also with 900°C. At first heater temperature is set to 500o
C and then it was gradually increased up to
900o
C. Temperature of the heater was set to 620o
C which is below the melting temperature of the matrix. An
electrical resistance furnace assembled with stainless steel impeller with 2 blade, 4 blade and 5 blade used as
stirrer was used for stirring purpose. A uniform semisolid stage of the molten matrix was achieved by stirring it
at 600 rpm. Pouring of preheated reinforcement at the semisolid stage of the matrix enhance the wettability of
17. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 38 | Page
reinforcement, reduces the particle settling at the bottom of the crucible. After stirring for 10 minutes at
semisolid stage slurry was reheated and hold at a temperature 900o
C to make slurry in liquid state. Stirrer rpm
was then gradually lowered to the zero. The molten composite slurry was then poured in to the metallic mould
which is preheated at temperature 500o
C this makes sure that the slurry is in molten condition throughout the
pouring.
Stirrer Blade preparation
Results indicated that composite fabricated using four blade stirrer shows better properties than two
blade and five blade [49].
V. Conclusion
After review of various literature on stir casting for production of aluminum metal matrix composites,
various process parameters of stir casting processand difficulties encountered in successful fabrication of
AMMC’s via stir casting technique, the following conclusions were made:
1. Stir casting method is the simplest and most economical method to produce good quality aluminium metal
matrix composites.
2. AMMC’s with larger particle size exhibit more homogeneous and uniform distribution in the matrix than
small particles.
3. Possibility of clustering of the reinforcements increases with increasing volume fraction of particles.
4. The nano-sized ceramic particles can be successfully incorporated into the aluminum matrix with a
reasonably uniform distribution, but the amount of porosity increases with increasing volume fraction of
nanoparticles, which can be attributed to the increased surface area of the nanoparticles.
5. In a combined route of stirring at semi-solid state followed by stirring at liquid state, the particle size and
rotation are the factors of greater influence on the incorporation of particles into the matrix, whereas the time
factor does not show any significant influence on the incorporation process.
6. Processing temperature, holding time influence on the viscosity of liquid metal and particles distribution, also
induce some chemical reaction between matrix and reinforcements, this varies depending on the type of
constituents. For good wettability, operating temperature should be kept at semisolid stage.
7. Wetting of ceramic particles occur during stirring at semisolid state because of interactions among the
particles themselves, between particles and solid aluminium and between particles and the remaining liquid
phase. Addition of a wettability-promoting agent,such as Mg, enhances the wettability between the particles and
aluminium.
8. Aluminium coated particles have higher wettability and better dispersion in the matrix because of their lower
melting point. This dispersion induces particles act as grain refiner of the melt. Furthermore, high nucleation
rate in melt which is result of great temperature difference between powder and melt which produces a spherical
and rosette-shaped grains, so this phenomena can reduce the viscosity of melt during casting process.
9. The impeller and stirring rod can be coated with liquid oxide such as alumina or zirconia so as to avoid any
metals contamination to the molten metal. For an optimized stirrer position, about 1/3 of material should be
below the stirrer and 2/3 of material should be above the stirrer.The stirring should be continued for few minutes
before, during and after feeding the reinforcement, also during the filling of the molten through the bottom of
the crucible. In case of using conventional stir casting, the stirring should be continued after the feeding the
reinforcement till just before the pouring. Hollow spindle stirring mechanism can be replaced the usual solid
shaft stirrer through the additions of ceramic particles turnings were introduced in small cylindrical capsules.
The method is suitable for eliminating the fading effect of inoculation and simultaneous addition of
reinforcements.
10. Blade design of the stirrer and preheating process are among the important factors to be considered in the
production of cast AMMC’s as these have an impact on quality and properties of casting. Toprevent or reduce
the formation of vortex at the surface of the melt as much as possible for the purpose ofuniform dispersion of
18. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 39 | Page
material,results of laboratory studies indicated that the blade angle should be 30°, 45°, 60° or 90°, and number
of blade should be 4.
11. Pouring temperature and pouring rate have significant impact on the metallurgical properties of composites
prepared using stir casting rout, depending on the type of composites.
12. Degasification tables of Hexachloroethane can be added into the melt instead of use of inert gas for removal
of gases from the molten alloy.The scum powder can be added into the melt which resulted into accumulation of
impurities at the surface of liquid melt.
13. Preheating the mould improves the soundness of the casting, shown by a decrease in the porosity level
14. Three step mixing method revealed an effective impact on the distribution of the nanoparticles. It showed
good incorporation of the particles and particles clustering, whereas poor incorporation of the particles and
particles clustering were observed in the case of nanocomposite fabricated using conventional stir casting
method.
15. Taguchi method has proved its success in prediction the optimum casting parameters to reach the best
metallurgical properties.
References
[1] J. Wiley & Sons, "Technology & Engineering – Handbook of Composite Reinforcements ", P 344-355, 30-Nov-1992.
[2] R. Calin, M. Pul and Z. Pehlivanli, The Effect of Reinforcement Volume Ratio on Porosity and Thermal Conductivity in Al-Mgo
Composites, Materials Research, 2012; 15(6): 1057-1063.
[3] N. Jit, A. Tyagi and N. Singh, Al-Cu-Si - (Al2O3)p composites using A 384.1 Al Alloys, Asian Journal of Chemistry Vol. 21, No. 10
(2009), S066-071.
[4] B. Kandpal, J. Kumar and H. Singh, Production Technologies of Metal Matrix Composite: A Review, IJRMET Vol. 4, Issue 2, Spl -
2 May - October 2014.
[5] S. Kulkarni, J. Meghnani and A. Lal, Effect of Fly Ash Hybrid Reinforcement on Mechanical Property and Porosity of Aluminium
356 alloy, Elsevier, Procedia Materials Science 5 (2014) 746-754.
[6] S. Shinde, Manufacturing of Aluminum Matrix Composite Using Stir Casting Method, IJIERT, Vol. 2, Issue 5, May-2015.
[7] P. Sharma, Production of AMC by stir casting – An Overview, International Journal of Contemporary Practices, ISSN: 2231-5608,
Vol.2, Issue 1.
[8] M. Balasubramanian, Composite Materials and Processing - Technology & Engineering, Handbook,P 276, 2013.
[9] J. Davis, Aluminum and Aluminum Alloys, Technology & Engineering, Handbook, P 164, 1993.
[10] W. Callister and Wiley, Material Science and Engineering, 9th Addition, 2011.
[11] N. Singh, S. Rai and S. Agarwal, Polymer Nanocomposites and Cr(VI) Removal from Water, Symbiosis, NB Singh, Research and
technology development centre, sharda university, Jan. 29, 2014.
[12] ASM International Handbook Committee: Composite, Engineered Materials Handbook, Volume 1, Third Printing, August 1989.
[13] Department of Defense USA, 2002, Composite Materials Handbook, Vol. 4, Metal Matrix Composites,
[14] Department of Defense USA, 2002, Composite Materials Handbook, Vol. 5, Ceramic Matrix Composites,
[15] K. Kainer, Metal Matrix Composites - Custom-made Materials for Automotive and Aerospace Engineering, 2006, ISBN: 3-527-
31360-5.
[16] K. Surappa, Aluminium matrix composites: Challenges and opportunities, Sadhana Vol. 28, Parts 1&2, February/April 2003, pp.
319–334.
[17] A. Khedera, G. Marahleh and ,D. Al-Jamea, Strengthening of Aluminum by SiC, Al2O3 and MgO. Jordan Journal of Mechanical
and Industrial Engineering, Volume 5, Number 6, Dec. 2011.
[18] D. Ramesh, R. Swamy and T. Chandrashekar, Effect of Weight Percentage on Mechanical Properties of Frit Particulate Reinforced
Al6061 Composite., ARPN Journal of Engineering and Applied Sciences, Vol. 5, No. 1, January 2010.
[19] W. Callister and Jr, Materials Science and Engineering, Department of Metallurgical Engineering, The University of Utah, seventh
edition, 2007.
[20] N. Cheremiisinoff, Handbook of ceramics and composites, synthesis and properties, Vol. 1, Marcel Dekker, New York-Basel 1990.
[21] D. Herling, G. Grant and others, Low-cost aluminum metal matrix composites, Advanced materials & processes, July 2001.
[22] V. Suong and Hoa, Handbook of science and engineering of composite materials, Vol. 21, Issue 4, Sep 2014.
[23] S. Suresh, D. Mishra and others, Production and characterization of micro and nano Al2O3 particle-reinforced LM25 Aluminum
alloy composites, Journal of Engineering and Applied Sciences, Vol. 6, No. 6, June 2011.
[24] T. Hashmi,Liquid state methods of Producing metal matrix composites: A Review, International journal of research in mechanical
engineering & technology, Vol. 5, Issue 1, Nov. 2014 – Apr. 2015.
[25] D. Roystan, Satyanarayen and others, A Study on mechanical properties of aluminum LM25- Sic composites fabricated using stir
casting, IJARTET, Vol. II, Special issue XXII, February 2015.
[26] K. Ranieria, C. Kiyana and others, Analysis of semi-solid processing for metal matrix composite synthesis using factorial design,
Materials research. 2012; 15(1): 144-150.
[27] A. Mazahery and M. Shabani, Characterization of cast A356 alloy reinforced with nanoSiC composites, Elsevier, Nonferrous met.
soc. China 22(2012) 275−280.
[28] M. Prakash and M. Jaswin, Microstructural analysis of aluminum hybrid metal matrix composites developed using stir casting
process, Int. J. Adv. Eng., 2015, 1(3), 333-339.
[29] M. Hassan, T. Ofor and others, Development of aluminum metal matrix composite using stir casting method, The international
journal of engineering and science (IJES) ,Vol. 3, Issue 8, P.36-39, 2014.
[30] S. Mathur and A. Barnawal, Effect of process parameter of stir casting on metal matrix composites, International journal of science
and research (IJSR), Vol. 2 Issue 12, Dec 2013.
19. Review of Effective Parameters of Stir Casting Process on Metallurgical Properties of Ceramics…
DOI: 10.9790/1684-12642240 www.iosrjournals.org 40 | Page
[31] G. Sozhamannan, S. Prabu and others, Effect of processingparameters on metal matrix composites: Stir casting process, Journal of
surface engineered materials and advanced technology, 2012, 2, 11-15.
[32] L. Saravanan and T. Senthilvelan, Fabrication and characterization of AL‐AL2O3nano composite, IJCESR, Vol. 2, Issue 1,2015.
[33] R.Raghuram, Investigation of vibration properties of aluminum, silicon carbide, Mica a hybrid metal matrix composite, IJLTET,
Vol. 5 Issue 2 March 2015.
[34] A. Singh, L. Kumar and others, Manufacturing of AMMC’s using stir casting process and testing it’s mechanical properties,
International journal of advanced engineering technology, July-Sept.,2013/26-29.
[35] R. Adat, S. Kulkarni and S. Kulkarni, Manufacturing of particulate reinforced aluminum metal matrix composites using stir casting
process, International journal of current engineering and technology, Vol.5, No.4, Aug 2015.
[36] A. Kumar, B. Naik and others, Optimization of casting parameters for casting of AL/RHA/RM hybrid composites using taugchi
method, IJETT, Vol. 4, Issue 8, August 2013.
[37] L. Singh, B. Ram and A. Singh, Optimization process parameter for stir casted aluminum metal matrix composite using taugghi
method, IJRET, Vol. 2, Issue 08, Aug-2013.
[38] R. Bhandare and P. Sonawane, Preparation of aluminum matrix composite by using stir casting method, International Journal of
Engineering and Advanced Technology, IJEAT, Vol. 3, Issue 2, Dec 2013.
[39] R. Calin, M. Pul and Z. Pehlivanli, The effect of reinforcement volume ratio on porosity and thermal conductivity in Al-Mgo
composites, Materials research, 2012, 15(6), 1057-1063.
[40] S. Dwivedi, B. Gupta and D. Chaudhary, The effect of process parameters on mechanical stir casting process, Journal of
engineering & technology, Vol. 1, Issue 2, 2013.
[41] S. Nair and N. Joshi, Preparation of Al 6061/ SiC metal matrix composite (MMC) using stir casting technique, IJARIIE, ISSN(O),
2395-4396, Vol. 1, Issue 3, 2015.
[42] B. Samal, S. Panigrahi and B. Sarangi, Use of modified stir casting technique to produce metal matrixcomposites, IJETR, ISSN:
2321- 0869, Vol. 1, Issue 9, Nov 2013.
[43] P. Melali, A. Mashayekhi and M. Shahmiri, Fabrication of high strength OF AL-base alloy composites reinforced with SiC
nanoparticles coated with Al and Cu, Association of Metallurgical Engineers of Serbia (AMES), Metall. mater. eng., Vol. 21 (2)
2015, p. 73-78.
[44] M. Wahab, A. Daud and M. Ghazali, Preparation and characterization of stir cast-aluminum metal matrix composites, International
Journal of Mechanical and Materials Engineering, Vol. 4, (2009), No. 2, 115-117.
[45] A. Micheal, A. Visu and others, Mechanical and corrosion properties of Al5034-Moo3 metal matrix composite, International Journal
of Innovative Research in Science, Engineering and Technology, Vol. 3, Special Issue 3, Mar 2014.
[46] A. Jailania and S. Tajuddin, Mechanical properties of stirred SiC reinforced aluminum alloy: stir casting with different composition
of SiC, blade angle and stirring speed. Advanced materials research, Vols. 622-623 (2013) pp 1335-1339.
[47] P. Kumar and V. Tirth, Effect of stirring speed on retention of particles in AA2218-Al2O3 MMC’s processed by stir casting, MIT,
International journal of mechanical engineering, Vol. 3, No. 2, Aug. 2013, pp. 123–128.
[48] S. Haque, A. Ansari and P. Bharti, Effect of pouring temperature and stirring speed on mechanical microstructure of AL6061- CU
reinforced SiCP metal matrix composites, IJRET, Vol. 03 Special Issue 10, Jun 2014.
[49] K. Paul and S. MT, Effect of stirrer parameter of stir casting on mechanical properties of aluminum silicon carbide composite,
IJMER, ISSN: 2249–6645, Vol. 5, Iss. 8, Aug. 2015.