This document discusses advancements in wireless power transfer (WPT) technology, focusing on optimizing performance and extractable power through improved circuit design methodologies. The proposed method involves actively controlling the load impedance and rectifier output to enhance efficiency, especially in applications like medical implants and consumer electronics. Experimental results demonstrate that the new optimization technique significantly outperforms traditional approaches in terms of efficiency and power transfer capabilities.

1. Journal for Research | Volume 02 | Issue 04 | June 2016
ISSN: 2395-7549
All rights reserved by www.journalforresearch.org 46
Advanced Optimization Circuit for Wireless
Power Transfer
Jai Prakash Sarwa Lumesh Kumar Sahu
M. Tech Student Assistant Professor
Department of Electrical Engineering Department of Electrical Engineering
Kalinga University, Raipur, Chhattisgarh, India Kalinga University, Raipur, Chhattisgarh, India
Abstract
The wi-fi energy transfer (WPT) is an emerging era with increasingly more ability packages to transfer energy from a transmitter
to a cellular receiver over a noticeably huge air gap. but, its extensive utility is hampered due to the relatively low performance of
modern wireless power switch (WPT) structures. This study gives an idea to maximize the performance in addition to to increase
the quantity of extractable electricity of a WPT system operating in resonant operation. The proposed method is primarily based
on actively modifying the equal secondary-side load impedance by controlling the section-shift of the active rectifier and its output
voltage degree. The offered hardware prototype represents an entire wireless charging machine, consisting of a dc–dc converter
that is used to price a battery at the output of the system. Experimental results are shown for the proposed concept in comparison
to a traditional synchronous rectification approach. The supplied optimization technique sincerely outperforms trendy solutions in
phrases of efficiency and extractable power.
Keywords: Wireless power transmission, electromagnetic induction
_______________________________________________________________________________________________________
I. INTRODUCTION
In today’s international of ever-increasing low-strength portable electronics, from implants to wireless accessories, powering those
devices efficiently and with no trouble is an escalating issue. The proposed solution is to wirelessly recharge these decrease-strength
transportable gadgets through a commonplace magnetic hyperlink with a higher-strength portable tool, consisting of a smart
telephone. Such a way is convenient for users, environmentally friendly, and reasonably-priced to enforce.
on the low-power stop, many medical implants depend on wireless energy to characteristic. One example is the cochlear implant,
a device with implanted electrodes that stimulate auditory nerves to sell hearing [5]. consistent with the meals and Drug
administration, as of December 2012, approximately 324,000 humans international have obtained those gadgets [10]. every implant
is coupled via a magnet to an energy transmitter out of doors the ear, which transfers milliwatts of strength wirelessly thru the skin.
Researchers also are growing retinal implants that stimulate electrodes in the attention to promote sight [4]. these medical devices
require at the order of 100 mW of wirelessly transmitted power. outside the clinical area, researchers are also investigating
structures to wirelessly fee lithium ion batteries at 10 mW charges [8].
In the center of the electricity spectrum, many industrial products are in the marketplace today that provide wi-fi strength for
famous consumer electronics such as cellular phones and pills. One instance is the Duracell Powermat, which a charging pad is
plugged into an electrical outlet that recharges well suited patron devices placed on top [6]. devices along with cell telephones may
be geared up with a special case to support wi-fi recharging.
on the excessive-electricity cease, at approximately 1 kW ranges, humans in each academia and enterprise are developing
technologies to power huge machines. At CES 2011, Fulton Innovation tested the generation to wirelessly price batteries in an
electric automobile [7]. Researchers are studying gadget designs for higher efficiency energy transfer to wafer processing machines
[9].
The proposed transportable wi-fi charging software differs from conventional charging pad based totally systems in that the
transmitter is strength restrained, so device efficiency is key. also, due to the fact each the transmitter and receiver are transportable,
loading at the transmitter changes dynamically, which affects efficiency and introduced strength
II. METHODOLOGY
The assignment is to develop efficient version for wi-fi charging circuit. in this paintings a sophisticated optimization approach for
a whole wireless charging device, which include an energetic rectifier and a DC-DC converter charging a battery, is investigated
in detail. The presented technique assumes non-resonant operation (IPT) and is based at the Qi trendy specs. while implemented
to an RPT device working exactly at resonance frequency, the reactive part of the device is inherently compensated, and
subsequently the proposed method shows the equal behavior as a synchronous rectifier. but, any deviation from the resonance
frequency, precipitated e.g. by means of parameter variations of the passive components, allows a performance increase of the
proposed idea over a synchronous rectification method. A stepped forward manipulate approach to actively adjust the resistive as
well as the reactive part of the equal load impedance is brought with a view to optimize the device overall performance. This

2. Advanced Optimization Circuit for Wireless Power Transfer
(J4R/ Volume 02 / Issue 04 / 09)
All rights reserved by www.journalforresearch.org 47
method, applicable to any IPT gadget, is used to in addition improve the machine performance and to extract more power. The
provided technique is primarily based on controlling both the segment shifts of the lively rectifier and its output voltage stage.
Fig. 1: Schematic block diagram of the overall WPT system including an inverter stage
the primary drawbacks of presently to be had WPT structures for patron applications are, amongst others, the pretty low normal
performance and the constrained strength switch functionality. This outcome in lengthy charging times which hampers the
significant application of the WPT technology. to overcome these issues numerous improvements had been counseled in literature.
design and optimization methodologies for growing the performance or the most transferable power of a WPT link were proposed
in assuming that the machine parameters are freely selectable. however, those optimization techniques aren't applicable to
commercial charging programs, where the system parameters are defined by a trendy.
III. RESULTS AND DISCUSSION
to test the efficacy of the proposed work, the device has been designed and simulated as proven beneath
Fig. 2: Simulink model of the overall WPT
The simulink model for the proposed paintings is shown inside the discern. The output of the device is given as shown in figure
3
Fig. 3: Output of the simulink model

3. Advanced Optimization Circuit for Wireless Power Transfer
(J4R/ Volume 02 / Issue 04 / 09)
All rights reserved by www.journalforresearch.org 48
After designing and enforcing of proposed technique with grid-linked solar photovoltaic system there would be a few anticipated
end result: firstly, perfect response for power transport into the gadget. Secondly resonance is acquired for optimum strength
transfer in device and performance is 86%.
IV. CONCLUSIONS
A wi-fi charging with a bifilar design for an MATLAB/SIMULINK version for wireless battery charging machine turned into
investigated, thru magnetic near discipline evaluation. It has located that the leakage flux from the uncovered coil became diverted
into the ferrite center, lowering the flux density from between 5mV to 10mV to 1.5mV to 2mV, which resulted to a discount of
about 5 instances. furthermore, a surest air hole distance in relationship to the operational frequency and load changed into
observed. change in resistance alters the resonant traits of the number one aspect. Computational simulation is utilized to improve
the performance of wireless charging.
REFERENCES
[1] Y. Lo, K. Chen, P. Gad, and W. Liu. A fully-integrated high-compliance voltage SoC for epi-retinal and neural prostheses. IEEE Transactions on Biomedical
Circuits and Systems, 7(16):761–772, December 2013.
[2] G.A. Kendir, W. Liu, G. Wang, M. Sivaprakasam, R. Bashirullah, M.S. Humayun, and J.D. Weiland. An optimal design methodology for inductive power
link with Class-E amplifier. IEEE Transactions on Circuits and Systems I, 52(5):857–866, May 2005.
[3] M.W. Baker and R. Sarpeshkar. Feedback analysis and design of RF power links for low-power bionic systems. IEEE Transactions on Biomedical Circuits
and Systems, 1(1):28–38, March 2007.
[4] G. Wang, W. Liu, M. Sivaprakasam, and G.A. Kendir. Design and analysis of an adaptive transcutaneous power telemetry for biomedical implants. IEEE
Transactions on Circuits and Systems I, 52(10):2109–2117, October 2005.
[5] P. Li and R. Bashirullah. A wireless power interface for rechargeable battery operated medical implants. IEEE Transactions on Circuits and Systems II,
54(10):912–916, October 2007.
[6] D. Kürschner and C. Rathge. Contactless energy transmission systems with improved coil positioning flexibility for high power applications. Power
Electronics Specialists Conference, pages 4326–4332, June 2008.
[7] K. Onizuka, H. Kawaguichi, M. Takamiya, T. Kuroda, and T. Sakurai. Chip-to-chip inductive wireless power transmission system for SiP applications. IEEE
Custom Integrated Circuits Conference, pages 575–578, 2006.
[8] P. Mercier and A.P. Chandrakasan. Rapid wireless capacitor charging using a multi-tapped inductively-coupled secondary coil. IEEE Transactions on Circuits
and Systems I, 60(9):2263–2272, 2013.
[9] A. S. Y. Poon, S. O’Driscoll, and T. H. Meng. Optimal frequency for wireless power transmission into dispersive tissue. IEEE Transactions on Antennas and
Propagation, 58(5):1739–1750, May 2010.
[10] M. Kiani, U. Jow, and M. Ghovanloo. Design and optimization of a 3-coil inductive link for efficient wireless power transmission. IEEE Transactions on
Biomedical Circuits and Systems, 5(6):579–591, December 2011.
[11] S. Guo and H. Lee. An efficiency-enhanced CMOS rectifier with unbalanced-biased com-parators for transcutaneous-powered high-current implants. IEEE
Journal of Solid-State Circuits, 44(6):1796–1804, June 2009.
[12] Y. Lam, W. Ki, and C. Tsui. Integrated low-loss CMOS active rectifier for wirelessly pow-ered devices. IEEE Transactions on Circuits and Systems II,
53(12):1378–1382, December 2006.
[13] G. Gosset and D. Flandre. A very high efficiency ultra-low-power 13.56 MHz voltage rectifier in 150nm SOI CMOS. IEEE International Symposium on
Radio-Frequency Integration Technology, pages 347–350, 2009.