This document provides an overview of principles of removable partial dentures, with a focus on supporting remaining teeth. It discusses indications for RPDs, principles of design, stress considerations, forces acting on partial dentures including levers and fulcrums. It covers biomechanical considerations of individual components like rests, major/minor connectors, direct retainers, and indirect retainers. Clasp designs are discussed as well as strategic clasp positioning to control stresses. The document emphasizes supporting remaining teeth and distributing stresses across components of the partial denture.
This seminar is of postgraduate level, which will be helpful for students. The presenter has added the information from various sources and the references are quoted in the last few slides of the seminar to gather more information about the seminar.
Failures in Fixed Partial Denture
(Prosthodontics FPD- Dental science)
Various types of failures in the fabrication of fixed partial denture
Dr.Sachin Sunny Otta
St.Gregorios Dental College,Kothamangalam,Ernakulam
This seminar is of postgraduate level, which will be helpful for students. The presenter has added the information from various sources and the references are quoted in the last few slides of the seminar to gather more information about the seminar.
Failures in Fixed Partial Denture
(Prosthodontics FPD- Dental science)
Various types of failures in the fabrication of fixed partial denture
Dr.Sachin Sunny Otta
St.Gregorios Dental College,Kothamangalam,Ernakulam
I will discuss various reference points for face bow.....
Thanks for watching......
If you like to watch my youtube channel..
please click for my channel....... Dr Aaryas Vlogs
https://youtu.be/myAENzQlHjE
One of the best seminar of the author. Covered in detail regarding the increasing vertical dimension, centric relation, methods to record centric relation, philosophies of occlusion and in detail everything about full mouth rehabilitation.
The following presentation is a compilation of RPD designing data from Mccraken and Stewart. it also includes data from evidence-based literature and recent practices
I will discuss various reference points for face bow.....
Thanks for watching......
If you like to watch my youtube channel..
please click for my channel....... Dr Aaryas Vlogs
https://youtu.be/myAENzQlHjE
One of the best seminar of the author. Covered in detail regarding the increasing vertical dimension, centric relation, methods to record centric relation, philosophies of occlusion and in detail everything about full mouth rehabilitation.
The following presentation is a compilation of RPD designing data from Mccraken and Stewart. it also includes data from evidence-based literature and recent practices
Stress exerted against the teeth and their attachment apparatus by occlusal forces may be within the adaptive capacities of the tissues or else the tissues may not be capable of compensation and adaptation and the result is tissue destruction
The scope of fixed prosthodontics treatment can range from the restoration of a single tooth to the rehabilitation of the entire occlusion. Single teeth can be restored to full function, and improvement in
esthetics can be achieved. Missing teeth can be replaced with fixed prostheses that will improve patient comfort and masticatory ability, maintain the health and integrity of the dental arches, and, in many instances, elevate the patient’s self-image.
differences between natural tooth periodontium and implant bone connection, biomechanics of implants, implant protected occlusion , occlusal principles for single tooth implant prosthetics and implant supported prosthesis on edentulous arch, shortened arch concept, therapeutic occlusion
A new version of designing partial denture in terms of Bio-kinetic. Actually this chapter consists a lot of information, however, it was edited in time limits. Thanks to Primary authors.
Retention and support in removable partial denture kalpanaKumari Kalpana
Retention of a removable prosthesis is a unique concern when compared with other prosthesis. Forces acting to displace the prosthesis from the tissue can consist of gravity acting against a maxillary prosthesis, the action of adherent foods acting to displace the prosthesis on opening of the mouth in chewing, or functional forces acting across a fulcrum to unseat the prosthesis.
2- b. Basic principles for designing Kennedy class II, III and IV Removable P...AmalKaddah1
1-a. Basic principles for designing the removable partial denture (class I partial denture design)
Introduction.
Objectives and Functions of RPD.
Factors that affect RPD design.
Basic principles for designing Kennedy class I partial denture.
2- b. Basic principles for designing Kennedy class II, III and IV Removable Partial Denture(RPD)
Description about mandibular movements, bennett movement, posselt's envelope of motion, sears axiom, concepts and schemes of complete denture occlusion. Detailed description of balanced occlusion, monoplane occlusion and lingualized occlusion. Selective grinding for both monoplane and semianatomic teeth. Added references for further readings.
Similar to 2. principles of designing rpd with special emphsis on support and perio (20)
Embracing GenAI - A Strategic ImperativePeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
2024.06.01 Introducing a competency framework for languag learning materials ...Sandy Millin
http://sandymillin.wordpress.com/iateflwebinar2024
Published classroom materials form the basis of syllabuses, drive teacher professional development, and have a potentially huge influence on learners, teachers and education systems. All teachers also create their own materials, whether a few sentences on a blackboard, a highly-structured fully-realised online course, or anything in between. Despite this, the knowledge and skills needed to create effective language learning materials are rarely part of teacher training, and are mostly learnt by trial and error.
Knowledge and skills frameworks, generally called competency frameworks, for ELT teachers, trainers and managers have existed for a few years now. However, until I created one for my MA dissertation, there wasn’t one drawing together what we need to know and do to be able to effectively produce language learning materials.
This webinar will introduce you to my framework, highlighting the key competencies I identified from my research. It will also show how anybody involved in language teaching (any language, not just English!), teacher training, managing schools or developing language learning materials can benefit from using the framework.
Safalta Digital marketing institute in Noida, provide complete applications that encompass a huge range of virtual advertising and marketing additives, which includes search engine optimization, virtual communication advertising, pay-per-click on marketing, content material advertising, internet analytics, and greater. These university courses are designed for students who possess a comprehensive understanding of virtual marketing strategies and attributes.Safalta Digital Marketing Institute in Noida is a first choice for young individuals or students who are looking to start their careers in the field of digital advertising. The institute gives specialized courses designed and certification.
for beginners, providing thorough training in areas such as SEO, digital communication marketing, and PPC training in Noida. After finishing the program, students receive the certifications recognised by top different universitie, setting a strong foundation for a successful career in digital marketing.
A Strategic Approach: GenAI in EducationPeter Windle
Artificial Intelligence (AI) technologies such as Generative AI, Image Generators and Large Language Models have had a dramatic impact on teaching, learning and assessment over the past 18 months. The most immediate threat AI posed was to Academic Integrity with Higher Education Institutes (HEIs) focusing their efforts on combating the use of GenAI in assessment. Guidelines were developed for staff and students, policies put in place too. Innovative educators have forged paths in the use of Generative AI for teaching, learning and assessments leading to pockets of transformation springing up across HEIs, often with little or no top-down guidance, support or direction.
This Gasta posits a strategic approach to integrating AI into HEIs to prepare staff, students and the curriculum for an evolving world and workplace. We will highlight the advantages of working with these technologies beyond the realm of teaching, learning and assessment by considering prompt engineering skills, industry impact, curriculum changes, and the need for staff upskilling. In contrast, not engaging strategically with Generative AI poses risks, including falling behind peers, missed opportunities and failing to ensure our graduates remain employable. The rapid evolution of AI technologies necessitates a proactive and strategic approach if we are to remain relevant.
Normal Labour/ Stages of Labour/ Mechanism of LabourWasim Ak
Normal labor is also termed spontaneous labor, defined as the natural physiological process through which the fetus, placenta, and membranes are expelled from the uterus through the birth canal at term (37 to 42 weeks
Francesca Gottschalk - How can education support child empowerment.pptxEduSkills OECD
Francesca Gottschalk from the OECD’s Centre for Educational Research and Innovation presents at the Ask an Expert Webinar: How can education support child empowerment?
June 3, 2024 Anti-Semitism Letter Sent to MIT President Kornbluth and MIT Cor...Levi Shapiro
Letter from the Congress of the United States regarding Anti-Semitism sent June 3rd to MIT President Sally Kornbluth, MIT Corp Chair, Mark Gorenberg
Dear Dr. Kornbluth and Mr. Gorenberg,
The US House of Representatives is deeply concerned by ongoing and pervasive acts of antisemitic
harassment and intimidation at the Massachusetts Institute of Technology (MIT). Failing to act decisively to ensure a safe learning environment for all students would be a grave dereliction of your responsibilities as President of MIT and Chair of the MIT Corporation.
This Congress will not stand idly by and allow an environment hostile to Jewish students to persist. The House believes that your institution is in violation of Title VI of the Civil Rights Act, and the inability or
unwillingness to rectify this violation through action requires accountability.
Postsecondary education is a unique opportunity for students to learn and have their ideas and beliefs challenged. However, universities receiving hundreds of millions of federal funds annually have denied
students that opportunity and have been hijacked to become venues for the promotion of terrorism, antisemitic harassment and intimidation, unlawful encampments, and in some cases, assaults and riots.
The House of Representatives will not countenance the use of federal funds to indoctrinate students into hateful, antisemitic, anti-American supporters of terrorism. Investigations into campus antisemitism by the Committee on Education and the Workforce and the Committee on Ways and Means have been expanded into a Congress-wide probe across all relevant jurisdictions to address this national crisis. The undersigned Committees will conduct oversight into the use of federal funds at MIT and its learning environment under authorities granted to each Committee.
• The Committee on Education and the Workforce has been investigating your institution since December 7, 2023. The Committee has broad jurisdiction over postsecondary education, including its compliance with Title VI of the Civil Rights Act, campus safety concerns over disruptions to the learning environment, and the awarding of federal student aid under the Higher Education Act.
• The Committee on Oversight and Accountability is investigating the sources of funding and other support flowing to groups espousing pro-Hamas propaganda and engaged in antisemitic harassment and intimidation of students. The Committee on Oversight and Accountability is the principal oversight committee of the US House of Representatives and has broad authority to investigate “any matter” at “any time” under House Rule X.
• The Committee on Ways and Means has been investigating several universities since November 15, 2023, when the Committee held a hearing entitled From Ivory Towers to Dark Corners: Investigating the Nexus Between Antisemitism, Tax-Exempt Universities, and Terror Financing. The Committee followed the hearing with letters to those institutions on January 10, 202
6. INDICATION FOR REMOVABLE PARTIAL
DENTURES
Stewart’s Clinical removable partial Prosthodontics 4th edition pg-8
1.Long standing edentulous area
2.No abutment tooth posterior
to the edentulous space
3.Reduced periodontal support
for remaining teeth
4.Need for cross ach stablization
7. INDICATION FOR REMOVABLE PARTIAL
DENTURES continued
Stewart’s Clinical removable partail prosthodontics 4th edition pg-8
5.Excessive bone loss within
the residual ridge
6.Physical or emotional
problem exhibited by the
patient
8. INDICATION FOR REMOVABLE PARTIAL
DENTURES continued
8) Immediate need to
replace extracted teeth
9) Patient desire
10)Unfavourable
maxillomandibular
relation.
Stewart’s Clinical removable partail prosthodontics 4th edition pg-8
9. PRINCIPLES OF DESIGN
• 1953,Dr.A.H.Schmidt gave the basic principles
of designing
1.Dentist should have thorough knowledge
2.Treatment plan must be based on complete
examination and diagnosis of individual patient.
10. 3.Dentist must correlate the pertinent factors and
determine a proper treatment plan
4.RPD should restore the function without injury to
remaining oral strutures
5.It is a form of treatment and not a cure.
11. STRESS CONSIDERATION IN A PARTIAL
DENTURE
The stresses can be divided as:
Vertical
Horizontal
Torsional
Displacing stresses
Dislodging stresses
14. HORIZONTAL STRESS
They originate as a component of rhythmic chewing
stroke. These forces are effective in mesio-distal
and buccolingual direction.
These lateral stresses are most damaging.
15. TORSIONAL STRESS
It is a twisting rotational type of force. It’s a
combination of vertical and horizontal force
17. McCracken’s Removable Partial Prosthodontics 11th edition
Is a rigid bar supported
somewhere along its
length..
The point where the bar is
supported is called the
fulcrum
Three classes of levers
(based on location of
fulcrum, resistance and
direction of effort (force).
Class I
Class II
Class III
LEVER
18. CLASS I LEVER
Fulcrum lies in the centre,
Resistance is at one
end and force at the other.
McCracken’s Removable Partial Prosthodontics 11th edition
19. CLASS II LEVER
Fulcrum is at one end effort
at the opposite end and
resistance in the centre.
McCracken’s Removable Partial Prosthodontics 11th edition
20. CLASS III LEVER
Fulcrum is at one end,
resistance at opposite
end and effort is in the centre.
McCracken’s Removable Partial Prosthodontics 11th edition
21. INCLINED PLANE
• Forces against an inclined plane may result in
deflection of that which is applying the forces or
may result in movement to the inclined plane,
neither of these is desirable
.
Stewart’s clinical Removable Posthodontics 4th edition
22. FULCRUM ON HORIZONTAL PLANE:
• Extends through the rest of principle abutments.
• Rotational movement of the denture in the sagittal plane.
Stewart’s clinical Removable Posthodontics 4th edition
23. DENTURE BASE MOVES AWAY FROM
SUPPORTING TISSUES:
Counteracted by:
Direct retainer
and
Indirect retainer
McCracken’s Removable Partial Prosthodontics 11th edition
24. DENTURE BASE MOVES TOWARDS THE
SUPPORTING TISSUES:
Counteracted by:
1) Occlusal rest.
2) Tissues of
supporting
ridge
McCracken’s Removable Partial Prosthodontics 11th edition
25. FULCRUM ON THE SAGITTAL PLANE
Extends through the occlusal rest on the terminal
abutment and along the crest of the ridge.
Movement is in the frontal plane
Stewart’s clinical Removable Posthodontics 4th edition
26. Counteracted by:
• Rigidity of major and
minor connector and
their ability to resist
torque.
• Close adaptation of the
denture base along the
lateral slopes and the
buccal slopes of the
palate and ridge.
• Direct retainer design McCracken’s Removable Partial Prosthodontics 11th edition
27. FULCRUM LOCATED IN MIDLINE JUST
LINGUAL TO THE ANTERIOR TEETH
(FULCRUM IS VERTICAL)
Rotational movement of denture in horizontal plane
or
flat circular movements of the denture
Stewart’s clinical Removable Posthodontics 4th edition
28. Counteracted by :
• Stabilizing components
(reciprocal arm and
minor connector)
• Rigid major connector
• Close adaptation of
denture base
McCracken’s Removable Partial Prosthodontics 11th edition
29. FACTORS INFLUENCING MAGNITUDE
OF STRESSES TRANSMITTED TO
ABUTMENT TEETH
1. Quality of support of ridge
Form of residual ridge
type of mucosal covering
2. Length of span
3. Clasp factor
design
length
material
amount of tooth contact
Stewart’s clinical Removable Posthodontics 4th edition
30. 4. Occlusion
Type of teeth
Harmony of occlusion
5. Areas of the base to which load is applied
Stewart’s clinical Removable Posthodontics 4th edition
31. 1. QUALITY OF SUPPORT OF RIDGE
• Better support by ridge less stress on abutment
teeth
• Large well formed ridges absorb greater stress
less stress on abutment
• Broad ridges with parallel
sides longer flanges on
the denture base stabilize
the denture against lateral
forces.
Stewart’s clinical Removable Posthodontics 4th edition
32. b. TYPE OF MUCOSA
• Influences magnitude of stresses transmitted to abutment
teeth.
• Healthy mucosa capable
of bearing greater functional
loads than thin atrophic
mucosa
• Soft, flabby, displaceable mucosa
Contribute little to vertical support of denture allows
excessive movement of denture stress transmitted to
abutment teeth
Stewart’s clinical Removable Posthodontics 4th edition
33. 2. LENGTH OF SPAN
• Longer edentulous span
longer denture base
greater force transmitted to
abutment teeth
• Every effort be made to retain a posterior abutment to
avoid class I and class II situation.
Stewart’s clinical Removable Posthodontics 4th edition
34. 3. CLASPAS A FACTOR IN STRESS
• More flexible the retentive arm of claspless
stress to abutment tooth
• But, flexible clasp arm provides less
stability against horizontal forces increase
stress on residual ridge.
• Decision should be made whether abutment
or ridge requires more protection
Stewart’s clinical Removable Posthodontics 4th edition
35. In examination phase decide whether ridge or abutment
tooth require more protection
If periodontal
support good
less flexible clasp
like vertical
projection clasp
If periodontal support
weak
use more flexible
clasp like
combination clasp
36. TYPE ABUTMENT TOOTH SURFACE
• Surface if gold crown offers more frictional
resistance to clasp arm movement than does
enamel surface of tooth.
• Greater stress exerted on tooth restored with
crown than with intact enamel.
Stewart’s clinical Removable Posthodontics 4th edition
37. AMOUNT OF CLASP SURFACE IN CONTACT
WITH TOOTH
Greater the area of tooth to metal contact between
clasp and tooth
more will be stress exerted on the tooth.
Stewart’s clinical Removable Posthodontics 4th edition
38. OCCLUSION AS A FACTOR
Disharmonious occlusion
generate horizontal stresses
when magnified by factor of leverage
can transmit destructive forces to both
abutment teeth and residual ridge.
Stewart’s clinical Removable Posthodontics 4th edition
39. TYPE OF OPPOSING OCCLUSION
• Play important role in determining amount of stress
generated by occlusion
• Natural teeth can exert closing force upto 300
pounds/inch square, whereas, complete denture upto 30
pounds/inch square.
• Therefore RPD constructed against removable prosthesis
is subjected to much less occlusal stress than one
opposed by natural dentition.
Stewart’s clinical Removable Posthodontics 4th edition
40. • AREA OF DENTURE BASE TO WHICH LOAD
IS APPLIED
• Less movement of base if load applied adjacent to the
abutment tooth than if it is applied to the distal end of
the base.
• movement may be 4 times greater at distal end of base
than next to the clasp.
42. REST
Two basic
types
Primary rest
Secondary rest
DIFERENT TYPES OF RESTS
1) Occlusal rest
2) Extended occlusal rest
3) Incisal ,lingaul or cingulum rest
4) Rest on restoration
5) Rest on cast restorations
43. REST
FUNCTIONS
• Provide vertical support for the partial denture.
• Maintains components in planned positions.
• Maintains established occlusal relations by preventing
settling of the denture base.
• Prevents impingement of soft tissue.
• Directs and distributes occlusal loads to abutment
teeth.
McCracken’s Removable Partial Prosthodontics 11th edition
45. If angle greater than 90 degrees
Forces not along long axis
but will create an inclined
plane effect
Slippage of prosthesis away
from the abutment
Orthodontic like forces McCracken’s Removable Partial Prosthodontics 11th edition
46. CINGULUM REST VS INCISAL REST
Cingulum rest nearer to center
of rotation
less tipping of tooth
Incisal rest
Longer minor connector required
magnifies the forces being transferred to the
abutment tooth
48. Kratochvil et al (JPD 1963:13;114)
• Suggested using mesial occlusal rest so that the force
delivered to the mesial aspect of the abutment tooth
• That would tend to tip that tooth forward maintaining a
tight contact with the tooth immediately anterior to it
and gaining stabilization and support from the remaining
anterior teeth.
• They suggested that occlusal rest be moved anterior to
better use the residual ridge for support.
.Kratochvil et al influence of occlusal rest position and clasp design on movement of abutment teeth J Prosthet Dent
1963:13;114
49. John W. Mc Cartney (JPD 1980;43:15)
Did a study on the effect of location of occlusal rest
on abutment tooth movement and concluded that
the mesial rest placement caused less abutment
movement than distal rest placement.
John W.McCartney Effect of location of rest and movement of abutment tooth J Prosthet Dent 1980:43:15
50. A major connector is the
component of the partial
denture that connects the
parts of the prosthesis
located on one side of the
arch with those on the
opposite side.
it also provides cross arch
stability to help resist
displacement stresses
MAJOR CONNECTOR
McCracken’s Removable Partial Prosthodontics 11th edition
51. DESIRABLE CHARACTERISTICS OF MAJOR
CONNECTORS
1.Should be rigid
2.Provide vertical support and protect the soft tissue.
3.Provide means of obtaining indirect retention where
indicated
4.Provide an opportunity of positioning denture bases
where needed
5.Maintain patient comfort
McCracken’s Removable Partial Prosthodontics 11th edition
52. MINOR CONNECTOR
1.Primary function is to join
other units of the prosthesis
such as clasp,rests,indirect
retainers and denture bases to
major connector
2.Distribution of stresses
McCracken’s Removable Partial Prosthodontics 11th edition
53. DESIGN CONSIDERATIONS
1.Should have sufficient bulk to be rigid
2. Should be made thick buccolingually and thin
mesiodistally
3.Should be in triangular form in embrassure
4. Should form a right angle with the major connector
5. Sharp angles should be avoided and spaces should not
exist for trapping of food debris.
Miller E.L. : “Text book of Removable Partial Prosthodontics”.
54. Any unit of
removable dental
prosthesis that engages
an abutment tooth in
such a manner as to
resist displacement of
the prosthesis away
from basal seat tissue.
DIRECT RETAINER
McCracken’s Removable Partial Prosthodontics 11th edition
55. • Prothero Cone theory as basis
of clasp retention
• Described shape of crowns of
premolar and molar teeth as 2
cones sharing a common base .
Line where they meet height
of contour. (represents the
greatest bulge).
• Suprabulge
• Infrabulge
McCracken’s Removable Partial Prosthodontics 11th edition
56. • Height of contour of tooth changes as the vertical
position of tooth changes.
• Surface is retentive if it is cervical to its height of
contour.
McCracken’s Removable Partial Prosthodontics 11th edition
57. • Clasp tip in infrabulge area resist the
movement in occlusal direction because to
release from tooth it has to undergo
deformation.
• Degree of resistance to deformation
determines the amount of clasp retention.
• Retention varied by:
depth of undercut
Flexibility of clasp arm positioned in undercut
Stewart’s Clinical removable partial Prosthodontics 4th edition
58. STRATEGIC CLASP POSITIONING AS A
MEANS OF STRESS CONTROL
• Leverages can be controlled to a large extent
by means of clasps, if there are sufficient
abutment teeth and they are strategically
distributed in the dental arch.
• If number and location of potential abutments
is less than ideal harmful effects can be
decreased by strategic placement of clasps.
Stewart’s Clinical removable partial Prosthodontics 4th edition
59. • Indicated most often in class III arches (with
modification space on opposite side)
QUADRILATERAL CONFIGURATION
McCracken’s Removable Partial Prosthodontics 11th edition
60. TRIPOD CONFIGURATION
Class II situations
Distal abutment on one
side of arch missing
leverage controlled to
some extent by creating
tripod configuration
of clasp placement.
McCracken’s Removable Partial Prosthodontics 11th edition
61. BILATERAL CONFIGURATION
For class I situations
Not considered ideal, but best
option available
Stress must be controlled by
other means.
McCracken’s Removable Partial Prosthodontics 11th edition
62. REQUIREMENTS OF CLASP
DESIGN
:
• Retention:provided by retentive terminal
• Support:mainly by rest
• Stability:all the component except the
retentive terminal
• Reciprocation:reciprocal arm
• Encirclement:must be designed more than
half of the circumference
• Passivity:engages only when dislodging forces
are applied
McCracken’s Removable Partial Prosthodontics 11th edition
67. Function: 1. to prevent the DEB
from moving away from its seat
because of cheek and tongue
forces, sticky food.
It uses mechanical advantage
of leverage by moving the
fulcrum line farther from the
force
McCracken’s Removable Partial Prosthodontics 11th edition
68. 2. Contributes to support and stability of the partial
denture counteracts horizontal forces applied to the
denture.
69. Effectiveness of indirect retainer depends
upon:
1) Its distance from the fulcrum line
greater the distance between fulcrum line
and IR more effective
70. 2) Effectiveness of direct retainer
Direct retainer must be effective if the
indirect retainer is to function when the
denture rotates
otherwise the partial
denture will be
dislodged.
71. Frank and Nicholls (JPD 1977:38;494)11
-did a study on the effectiveness of indirect retainer and
concluded that use of a mesial rest instead of a distal rest
on the terminal abutment tooth does not decrease
indirect retention.
Thus the choice of indirect retainer location should be
made mostly on the basis of abutment tooth support, a
crown form favoring adequate rest seat preparation, and
the patients esthetic desires.
72. Frechette et al (JPD 1956;6:195-212)
demonstrated that removal of the indirect retainers
from a RPD results in the application of more
pressure to the direct abutment teeth. The indirect
retainer probably is effective in distributing forces to
teeth other than direct abutments, and in preventing
denture base lifting.
73. PHILOSOPHIES OF DESIGN
• There are three basic design philosophies:
• Stress Equalization
• Physiologic Basing
• Broad stress distribution
74. ESSENTIALS OF PARTIAL DENTURE
DESIGN
• Should be systematically developed on the
diagnostic cast based on the following.
1) Where is the prosthesis supported.
2) How the support is connected.
3) How the prosthesis is retained.
4) How the retention and support are connected.
5) How the edentulous base support is connected
McCracken’s Removable Partial Prosthodontics 11th edition
75. WHERE IS THE PROSTHESIS SUPPORTED.
Tooth supported
Tooth - tissue supported:
76. TOOTH SUPPORTED
1) The most ideal support units are the RESTS.
2) The abutment selected for the support has to be
evaluated for
• Periodontal health.
• Crown- root ratio.
• Crown –root morphology
• Location of the tooth in the arch
• The opposing dentition
77. TOOTH- TISSUE SUPPORTED
Depends on 6 factors:-
1) Quality of residual ridge
2) The extent to which the ridge will be covered by mucosa
3) The accuracy and type of impression registration
4) The design chracteristics
5) The occlusal load applied
78. STRESS EQUALIZATION
• The resiliency of the tooth supported by periodontal ligament in
an apical direction is not comparable to the greater resiliency
and displacement of the mucosa covering the dentulous ridge.
• It is the belief of this school of thought that the rigid connection
between the denture base and the direct retainer on the
abutment teeth is damaging
79. • Thus some form of stress director or stress equalizer is
essential to protect the abutment teeth.
• The most commonly used ones are composed of a hinge
device interposed between the minor connector of the
abutment tooth and the denture base.
80. PHYSIOLOGIC BASING
The belief is that the equalization can best and most simply
be accomplished by some form of physiologic basing.
• The physiologic basing is produced either by
• Displacing or depressing the ridge mucosa during the
impression making procedure
• Relining the denture base after it has been constructed.
81. Displacing the mucosa during the impression procedure
records it in its functioning and not the anatomic form.
This denture base formed over displaced tissue, will adapt
more readily to the depressed tissue when occlusal force
acts and will be better able to withstand the force that is
generated
82. BROAD STRESS DISTRIBUTION
distributing the forces of
occlusion over as many teeth
and as much of the available
soft tissue area as possible.
This is accomplished by the
use of additional rests,
indirect retainers, clasps and
broad coverage denture
bases
83. STEP BY STEP DESIGNING
Diagnostic cast area of recontouring
Black-mark survey lines desired undercut is measured
87. REFERENCES
1) McCracken’s removable partial Prosthodontics 11th
edition.
2) Stewart’s Removable partial Prosthodontics 4th
edition.
3) David M Watt; A Roy Macgregar :Designing
partial dentures.
4) Miller E.L. : “Text book of Removable Partial
Prosthodontics”. St. Louis, CV Mosby Co.
88. 5) Kratochvil et al influence of occlusal rest position and
clasp design on movement of abutment teeth J Prosthet
Dent 1963:13;114
6) John W.McCartney effect of location of rest and
movement of abutment tooth J Prosthet Dent 1980:43:15
7) David N Firtell reaction of anterior abutment of kennedy
classII removable partial denture to various clasp arm
designs J Prosthet Dent 1985:53;77
8) Richard P Frank direct retainers for distal extension
removable partial dentures J Prosthet dent 1986:56;562
89. 9) Frank and Nicholis an investigation of effectiveness
of indirect retainer J Prosthet dent 1977:38;494
10)Frechette et al the influence of partial denture design
on distribution of force to abutment teeth J Prosthet
Dent 1956:6;195
11)A.H.Schmidt Planning and designing removable
partial denture J Prosthet Dent 1953:3;783
These are the 7 wonders of the world. Wt is common among all of them????? They are all man made structures that where build with so much pesicion and planning till date people don’t forget. Similar a rpd also has to be palnned in such a way tha I remains life long in the patients.
Those forces which are the result of downward
stresses along
the long axis of
the teeth in a crown
to apex direction and
the relatively vertical
stresses on the ridge
mucosa.
These are the forces which tend to lift the partial
denture from it’s rest position. Reciprocal dislodging action occurs when
wide edentulous spaces
are interrupted by few
teeth thus inviting an
antero-posterior or
lateral tilt of prosthesis.
They originate as a component of rhythmic chewing stroke. These forces are effective in
mesio-distal and
buccolingual direction.
These lateral stresses
are most damaging.
It is a twisting rotational type of force. It’s a combination of vertical and horizontal force.
Torsion is noted most
frequently where a
long segment acts
upon the first abutment
it engages. Where the
ridge mucosa has higher
resiliency torque is higher. Torque applies rotation about a fixed point.
A lever amplifies an input force to provide a greater output force, which is said to provide leverage. The ratio of the output force to the input force is the ideal mechanical advantage of the lever.The bar can only move about the fulcrum
Lever should be avoided in the design
Althought he movement of the denture will be minimal the lever that I imposed onto the abutment is great and is detramental.
Resulting forces on abutment tooth from rotation in sagital plane is usually in mesioapical or distoapical direction with the greatest magnitude in apical direction..
The denture movement occurs towars or away from the denture base
Hence wrought retentive clasp was rcommended for cla 1 2
35
Any component that of a partial denture on a tooth surface that provides vertical support is called rest.
They serve to transmit vertical forces to the abutment and direct those forces along the long axix of the tooth
Any component that of a partial denture on a tooth surface that provides vertical support is called rest.
They serve to transmit vertical forces to the abutment and direct those forces along the long axix of the tooth
The outline has to be rounded tringular shape, with apex towards the centre
It should be as long as its witdht
The rest seat should be around 2.5mm
Margins have to be smmoth
Reduction of the marginal ridge should be 1.5mm so as to give bulk to the material
Floor has to be concave,spoon shaped.
In such case a secondary rest have to be given
First requirment is ridity…this allows stresses that are applied to any portion of the partial denture to be effectively distributed over the entire area of support,including abutment teeth,other teeth included in design,underlying bone and soft tissue….perhaps the greatest damage to a partial denture produce is that which results from the flexible major connector..
2.The major connector should never terminate on the free gingival margine because the marginal gingiva is highly vascular and susceptible to injury from pressure..it should be atleast 6mm from gingival crevice….and in mandibular arch it should be at least 3mm from gingival margin…
Minor connectors can be defined as the connecting link between the major connector or base of a removable partial denture to other units of a prosthesis such as clasp assembly,indirect retainers,rests etc
The ability of the direct retianer to fucntion is greatly depending upon the stabilit and support provided by the major minor connector and the rest and tissue surface
When 4 abutment teeth available for clasping and partial denture confined within 4 clasps all leverages neutralized.
Ideal (for support and leverage control)
It has to be noted that all the factors are interdependent on each other
Of the various philosophies relating to RPD design, none is backed by scientific research or statistics.
This is not to say that none of the various methods of design has proved to be clinically acceptable.
On the contrary, all have produced excellent clinical results if attention to detail has been observed.
Prepared on the occlusal, incisal, cingulaum surfaces
Primarily comes from the overlying soft tissue.
Underlying alveolar bone.
This design philosophy agrees to some extent to the first school about the relative lack of movement of the abutment teeth in an apical direction
But denies the necessity of using stress directors to equalize the disparity of vertical movement between the tooth and mucosa.
Color coding:
Red: placement of tripod marks areas of recontoured rest seats (solid rest)
Black: survey lines information on base of the cast
Blue :portions to be made of acrylic
Brown: To outline the metallic part all the
component