05_04R201_1_C200 Hardware Configuration.ppt

1
1
April 9, 2023
Describe the Configuration of C200
Hardware and I/O
C 200 Hardware configuration
Describe the Configuration of C200 Hardware and I/O
ExperionPKS Control Execution Environment EXP04R201

Honeywell
2
April 9, 2023
• Objectives:
– Identify Hardware, Slot Numbers and Addressing for the C200
Controller and Rack Components
– Use Control Builder to Build and Download Hardware
Configurations
Configure C200 Hardware

Honeywell
3
April 9, 2023
10 slot chassis
Power supply
ControlNet Interface (CNI)
or FTE Bridge
Control Processor (C200)
IO Link Interface Module
Fieldbus Interface Module
Redundancy Module
CNI to Remote I/O
Below is an example C200 rack configured with:
1
2
3
4
5
6
7
8
5 6 7 8
4
3
2
1

Honeywell
4
April 9, 2023
Finding the location of hardware in your chassis
• To determine the IOM Slot Number you must:
– Start counting at zero (do not count the Power Supply)
– Count from left to right
– Count both spaces if the module occupies two spaces
Determining Slot Numbers
Power Supply 1
2
3
4
5
6
7
8
0
9

Honeywell
5
April 9, 2023
Follow these steps to add a new
Controller (CPM) from the pull-down
menus

Honeywell
6
April 9, 2023
Configuring a Control Processor Module (CPM)
MAC ID of CNI
card connected
to the Server
ControlNet or Ethernet driver
CNI Slot #
Slot number of the CPM
(Control Processor)
Check for redundant controller
and then enter its name
Data entry details
will be provided in
the Lab exercise

Honeywell
7
April 9, 2023
History parameters, Control Level required to operate this CPM, and the
Area to which this Controller belongs are defined on the Server History tab.

Honeywell
8
April 9, 2023
Point, Group, Trend and
Associated Displays (which
reside on the Server) are
defined on the Server
Displays tab.
Select “OK” to close and
save the new controller

Honeywell
9
April 9, 2023
• Double-click or right click the CEE
to open the configuration form
shown on the next page
• Click the + sign to expand the
CPM in the Project tab
CEE0101
Configuring a Control Execution Environment (CEE)

Honeywell
10
April 9, 2023
Configuring a Control Execution Environment (CEE)
Data entry details
will be provided in
the Lab exercise

Honeywell
11
April 9, 2023
Fault Tolerant Ethernet Bridge (FTEB)
• Fault Tolerant Ethernet Bridge (FTEB)
– Single wide chassis module
– Connects to FTE cable A and B
– Supports chassis redundancy
– Can only be used for Supervisory
Control Network connection
– ControlNet and downlink CNI’s
required for all IO communications
including p2p to AB devices
– Rotary switch for FTE Node Number (1to99)

Honeywell
12
April 9, 2023
Fault Tolerant Ethernet Bridge (FTEB)
• Fault Tolerant Ethernet Bridge (FTEB)
– The FTEB can be used for FIM only connections to the Supervisory
network
– In the Project and Monitoring tabs in control builder you will now see
the FTEB as the Root for the CPM!!!!
– You will be setting the FTEB up using IP addresses! An FTE
community can only have 99 FTEB’s so, you are limited to 49
Redundant pairs and 99 single in one community.
– The FTE connection to the FTEB is 10Mbps. 10Mbps is only
supported in FTE for connection from FTEB to a switch, nowhere
else.

Honeywell
13
April 9, 2023
FTEB Confiuration

Honeywell
14
April 9, 2023
The Control Processor Module (CPM) and its Control Execution
Environment (CEE) have now been configured - but not yet
downloaded.
CEE0101

Honeywell
15
April 9, 2023
Configuring Input/Output Modules (IOMs)
Menu Method

Honeywell
16
April 9, 2023
 Select the Library tab from the tree view to
display a list of devices
– SYSTEM (containers for function
blocks)
• Control Module
• SCM (Sequential Control Modules)
– IOMODULE
• All available Rack I/O Modules
– PMIO
• All available PM type IO modules
– Rail IO Non-Hazardous
Environments
– Rail IO Hazardous Environments
From the Library Tab

Honeywell
17
April 9, 2023
Control Builder
automatically
names the IOM
1 2

Honeywell
18
April 9, 2023
This Modules Slot Number
MAC Address of the Remote
Rack’s CNI Card
Slot Number of the CNI in
the Processor Rack that this card
will Communicate Through

Honeywell
19
April 9, 2023
Assigning Input/Output Modules (IOMs)
2
1
3
Assigned
to CEE

Honeywell
20
April 9, 2023
Loading the Controller, CEE and IOMs
Not yet
loaded

Honeywell
21
April 9, 2023
Loading the Controller, CEE and IOMs
Verify that the
items to load
are checked
Note:
You can decide to
have the modules
go to the active
state automatically
by clicking this
checkbox with the
Post Load State
selected to be
“Active”

Honeywell
22
April 9, 2023
Activating a Control
Strategy
Right-click CEE
Blue: The object is not running or Inactive
Green: The object is running or Active

23
23
April 9, 2023
Describe the Import/Export Procedure in
Control Builder
Describe the Import/Export Procedure in Control Builder

Honeywell
24
April 9, 2023
• Objectives:
• Understand Control Builder’s Import Function
• Understand Control Builder’s Export Function
Control Builder - Import/Export

Honeywell
25
April 9, 2023
Control Builder
(Server 1)
Control Builder
(Server 2)
Control
Strategy
Configuration
Project
Tree
Control
Strategy
Configuration
Project
Tree
Ixport Directory
Export
Data
Import
Data
Control Builder - Import/Export
CM’s and SCM’s and Hardware configuration can be moved between
servers using Import/Export

Honeywell
26
April 9, 2023
The Export function lets you
export all or a portion of the
ERDB viewed in the Project
Tree to the Ixport folder or a
user-defined location.
The exported portions or all of the ERDB are
stored in the Ixport folder at directory location
C:Program FilesHoneywellExperion
PKSEngineering Tools by default.
Control Builder - Export

Honeywell
27
April 9, 2023
In Control Builder, select File > Export to call up the dialog box shown:
All items in
current project
ImportExport
text files target
location
Select to start
Export
Use Selection
buttons (or use
<Ctl> + mouse
select or
<Shift> +
mouse select to
export specific
CMs from the
Point window)
List of items to
Export based
on selections
from window
(Export.sl)

Honeywell
28
April 9, 2023
Exporting Data Dialog Box

Honeywell
29
April 9, 2023
In Control Builder, select File > Import to call up the dialog box shown:
All items in current
Import/Export text
files location
ImportExport text
files target location
Import and Assign
Select to start Import
When enabled,
your own list of
items to Import
(Filename.sl)
Use Selection
buttons (or use
<Ctl> + mouse
select or <Shift> +
mouse select to
import specific
CMs from the
Point window)
List of items to
Import based on
selections from
window (Import.sl)
Control Builder - Import

Honeywell
30
April 9, 2023
This page intentionally left blank

05_04R201_1_C200 Hardware Configuration.ppt

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Similar to 05_04R201_1_C200 Hardware Configuration.ppt

Similar to 05_04R201_1_C200 Hardware Configuration.ppt (20)

Recently uploaded

Recently uploaded (20)

05_04R201_1_C200 Hardware Configuration.ppt

Editor's Notes