3D integrated circuits can alleviate problems associated with increasing chip complexity by integrating multiple layers of active components vertically. This reduces interconnect length and delays, lowers power dissipation, and facilitates heterogeneous integration. 3D ICs can be constructed using different techniques like monolithic, wafer-on-wafer, die-on-wafer, and die-on-die approaches. The technology offers advantages like improved performance, reduced chip area and costs, and better noise isolation of digital and analog circuits. While thermal and reliability issues require attention, 3D ICs are expected to replace conventional chips in applications like mobile devices due to their reduced size, cost and power consumption.
2. • There is a saying in real estate; when land get
expensive, multi-storied buildings are the
alternative solution. We have a similar
situation in the chip industry.
WHY 3D ICs…..??
3. Additionally heterogeneous integration of different technologies in one single
chip is becoming increasingly desirable, for which planar (2-D) ICs may not be
suitable.
3-D ICs are an attractive chip architecture that can alleviate the interconnect
related problems such as
Delay and power dissipation and can also facilitate integration of
heterogeneous technologies in one chip.
With the Introduction of 3-D ICs, the world of chips may never
look the same again.
4. Contents
INTRODUCTION
IDEA FOR 3D IC
LIMITED PERFORMANCE OF 3D IC
3D ARCHITECTURE
MANUFACTURING TECHNOLOGY OF 3D Ics
ADVANTAGES OF 3D ARCHITECTURE
PERFORMANCE CHARACTERISTICS
CONCERN IN 3D CIRCUITS
PRESENT SENARIO IN 3D INDUSTRY
CONCLUSION
5. Introduction
• In electronics, a three-dimensional integrated circuit is a chip in which
two or more layers of active electronic components are integrated
both vertically and horizontally into a single circuit.
• In contrast , a 3D IC is a single chip in which all components on the
layers communicate using on-chip signaling, whether vertically or
horizontally.
6. IDEA FOR 3D IC
The large growth of computer and information technology industry is
depending on VLSI circuits with increasing functionality and
performance at the minimum cost and power dissipation and 2D ICs
generate various gate delays and interconnection delay.
So to reduce these delays and total power consumption ,
3D IC technology is introduced.
• Intel introduced 80 core chip in 2007 which run on the frequency of
1.4GHz.
7. LIMITED PERFORMANCE OF 2D ICs
• As we try to increase the performance and efficiency of chip, the
complexity of chip design increases and this requires more and
more transistors . So the final size of the circuit and delay increases.
• The losses increases with large interconnection because the
capacitance and resistances are generated in between the clad and
the copper.
9. 3D IC is a concept that can significantly :-
• Improve interconnect performance ,
• Increase transistor packing density,
• Reduce chip area
• Power dissipation
In 3D design structure the entire chip ‘Si’ is divided by number of
layers of oxide and metal, to form transistors.
10. MANUFACTURE TECHNOLOGY OF 3D ICs
There are four ways to build 3D ICs :-
1.Monolithic
2. Wafer on wafer
3. Die on wafer
4. Die on die
11. 1. Monolithic
Electronic components and their connections (wring) are built in layers on a single
semiconductor wafer, which is then diced into 3D ICs. There is only one substrate,
hence no need for aligning ,thinning, bonding , or through-silicon vias.
12. 2. Wafer on wafer
Electronic components are built on two or more semiconductor wafers , which are
then aligned, bonded, and diced into 3D ICs.
Each wafer may be thinned before or after bonding.
13. 3. Die on wafer
Electronic components are built on two semiconductor wafers. One wafer is diced
aligned and bonded onto die sites of the second wafer.
14. 4. Die on die
Electronic components are built on multiple dice, which are then
aligned and bonded.
One advantage of die-on-die is that each component die can be tested
first, so that one bad dies does not ruin on entire stack
15. ADVANTAGES OF 3D ARCHITECTURE
• 3D integration can reduce the wring ,thereby reducing the capacitances, power
dissipation and chip area, improves performance.
• Digital and analog circuits can be formed with better noise performance.
• It more cost effective than 2D integration.
17. 1. TIMING
• The graph shows the results of a reduction in wire length due to 3D routing.
• Reduction in the interconnect lengths reduces RC
delays and increase chip timing performance
18. 2. ENERGY PERFORMANCE
• Energy dissipation decreases with the number of layers used in the design
• The graph shows the reduction in a normalized energy consumption with number of wire layers.
19. CONCERNS IN 3D CIRCUIT
• Thermal issues in 3D-circuits
• Reliability issues
20. PRESENT SCENARIO IN 3D IC INDUSTRY
Many companies like MIT (USA), IBM are doing research on 3D IC technology and
they are doing
Research on 3D IC technology and they are going to introduce cheaper chips for
certain applications, like memory used in digital cameras, cell phones, handled
gaming devices etc.
The original cost will be 10 times lesser than the current ones.
21. CONCLUSION
3D ICs will be the first of new generation of dense, inexpensive chips
having less delay and interconnection losses that will replace the
conventional storage and recording media.