Công ty TNHH Hạo Phương Chuyên phân phối các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới. www.haophuong.com

2. Contents
3
4
6
18
Overview - Actuators
Product Selection Actuators
Non-Spring return Damper Actuators 5Nm, 10Nm, 20Nm, 34Nm
Spring return Damper Actuators 5Nm, 10Nm, 20Nm
22
Fire and Smoke Damper Actuators

3. Overview - Actuators
Damper actuator advantage
High reliability
Accurate runtime
Same rating torque,
actual output torque
higher
Easy wiring
Feature
MCU control,
no limitswitch
needed
Motor overheated is
prevented;
Product service
life long
The motor speed is
real-time adjusted
Actual output torque
is 1.3 times
the rating one
Actuator and wiring
box are separate,
and terminal block
is incorporated
in wiring box
Function
Accurate positioning
control, runtime
not varied with load
Smaller-sized
actuator is equivalent
to the bigger one
from competitor’s
Saving wiring time
No insulation tape
needed
Benefit
Non Spring Return
(CN series)
Fire and Smoke Damper Actuator
(MS Series)
Spring Return
(CS series)
5Nm
CN4605
CN6105
CN7505
10Nm
CN4610
CN6110
CN7510
20Nm
CN4620
CN6120
CN7220
34Nm
CN4634
CN6134
CN7234
5Nm
CS4105
CS7505
CS8105
10Nm
CS4110
CS7510
CS8110
20Nm
CS4120
CS7520
CS8120
510
0
Spring return direct coupled actuators
(DCA) for on/off damper control. The
actuator accepts an on/off signal
from a single-pole, singlethrow
(SPST) controller. They are designed
to operate reliably in smoke control
systems requiring Underwriters
Laboratories Inc. UL555S ratings up
to 350 F.
3

4. Product Selection - Actuators
4
NON - SPRING RETURN Power
Supply
Control Input/Output Price List
Number
(without whips)
Running
Time
(50Hz)
24
VAC/
DC
220
VAC
On/Off
Two
position
Floating
0/2-10 VDC
Modulating
Feedback
(0/2-10
VDC)
SPDT
Auxiliary
Switches
(USD)
CN05 Series (5 Nm, 44 lb-in)
CN4605A1001 110 • • 0 148.64
CN4605A1201 110 • • 2 (*)
CN4605A2001 110 • • • 0 (*)
CN4605A2201 110 • • • 2 (*)
CN6105A1011 90 • • • 0 153.91
CN6105A1201 90 • • • 2 (*)
CN6105A2001 90 • • • • 0 (*)
CN6105A2201 90 • • • • 2 (*)
CN7505A1001 110 • • • • 0 (*)
CN7505A1201 110 • • • • 2 (*)
CN7505A2001 110 • • • • • 0 166.37
CN7505A2201 110 • • • • • 2 (*)
CN10 Series (10 Nm, 88 lb-in)
CN4610A1001 110 • • 0 158.85
CN4610A1201 110 • • 2 (*)
CN4610A2001 110 • • • 0 (*)
CN4610A2201 110 • • • 2 (*)
CN6110A1003 90 • • • 0 159.41
CN6110A1201 90 • • • 2 239.68
CN6110A2001 90 • • • • 0 (*)
CN6110A2201 90 • • • • 2 (*)
CN7510A1001 110 • • • • 0 (*)
CN7510A1201 110 • • • • 2 (*)
CN7510A2001 110 • • • • • 0 (*)
CN7510A2201 110 • • • • • 2 (*)
CN20 Series (20 Nm, 177 lb-in)
CN4620A1007 110 • • 0 (*)
CN4620A1207 110 • • 2 (*)
CN4620A2007 110 • • • 0 (*)
CN4620A2207 110 • • • 2 (*)
CN6120A1006 110 • • • 0 301.98
CN6120A1207 110 • • • 2 (*)
CN6120A2007 110 • • • • 0 (*)
CN6120A2207 110 • • • • 2 (*)
CN7220A1007 110 • • • • 0 (*)
CN7220A1207 110 • • • • 2 (*)
CN7220A2007 110 • • • • • 0 353.74
CN7220A2207 110 • • • • • 2 (*)
CN34 Series (34 Nm, 300 lb-in)
CN4634A1003 110 • • 0 401.01
CN4634A1208 110 • • 2 (*)
CN4634A2008 110 • • • 0 (*)
CN4634A2208 110 • • • 2 (*)
CN6134A1003 110 • • • 0 401.01
CN6134A1208 110 • • • 2 (*)
CN6134A2008 110 • • • • 0 (*)
CN6134A2208 110 • • • • 2 (*)
CN7234A1008 110 • • • • 0 (*)
CN7234A1208 110 • • • • 2 (*)
CN7234A2008 110 • • • • • 0 390.71
CN7234A2208 110 • • • • • 2 (*)
CN46
CN46
CN61
CN61
CN61
CN61
CN75
CN75

5. Product Selection - Actuators
SPRING RETURN Running Time
Power
Supply
Control Input/Output
Auxiliary
Knob
Price List
Number
(without whips)
Drive
(sec)
Spring
Return
(sec)
24 VAC/
DC
100-
250
VAC
On/Off
Two
position
Modulating
and Floating
Feedback
(0/2-10
VDC)
SPDT
Auxiliary
Switches
(USD)
CS05 Series (5 Nm, 44 lb-in)
CS4105A1002 90 <20 • • 0 305.28
CS4105A1102 90 <20 • • 0 (*)
CS8105A1008 90 <20 • • 0 276.34
CS8105A1102 90 <20 • • 0 (*)
CS7505A2008 90 <20 • • 0 334.09
CS7505A2202 90 <20 • • • 2 (*)
CS10 Series (10 Nm, 88 lb-in)
CS4110A1002 90 <20 • • 0 302.01
CS4110A1200 90 <20 • • 0 396.06
CS8110A1008 90 <20 • • 0 272.56
CS8110A1206 90 <20 • • 0 363.01
CS7510A2008 90 <20 • • 0 357.75
CS7510A2206 90 <20 • • • 2 416.26
CS20 Series (20 Nm, 175 lb-in)
CS4120A1001 90 <20 • • 0 318.63
CS4120A1209 90 <20 • • 0 414.69
CS8120A1007 90 <20 • • 0 286.83
CS8120A1205 90 <20 • • 0 381.19
CS7520A2007 90 <20 • • 0 356.09
CS7520A2205 90 <20 • • • 2 439.81
FIRE AND SMOKE
SPRING RETURN
Running Time Power Supply Control Input/Output
Auxiliary
Knob
Price List
Fast acting, two
position spring
return. Rating
up to 350o
F
Number
(without whips)
Drive
(sec)
Spring
Return
(sec)
24 VAC
120
VAC
230
VAC
On/ Off Two
position
Feedback
(0/2-10
VDC)
SPDT
Auxiliary
Switches
(USD)
MS04 Series (4 Nm, 44 lb-in)
MS4104F1010 15 <15 • • 0 (*)
MS4104F1210 15 <15 • • 2 (*)
MS4604F1010 15 <15 • • 0 (*)
MS4604F1210 15 <15 • • 2 (*)
MS8104F1010 15 <15 • • 0 (*)
MS8104F1210 15 <15 • • 2 (*)
MS09 Series (9 Nm, 80 lb-in)
MS4109F1010 15 <15 • • 0 (*)
MS4109F1210 15 <15 • • 2 (*)
MS4609F1010 15 <15 • • 0 523.50
MS4609F1210 15 <15 • • 2 257.50
MS8109F1010 15 <15 • • 0 (*)
MS8109F1210 15 <15 • • 2 (*)
M
M
M
M
M
M
CS7
CS1
CS4
CS4
CS8
CS8
CS7
CS7

6. CN05, CN10 SERIES
NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS
FOR FLOATING AND TWO-POSITION CONTROL
PRODUCT DATA
GENERAL
This non-spring return direct-coupled damper actuator
provides floating and two-position control for:
• air dampers,
• VAV units,
• air handlers,
• ventilation flaps,
• louvers, and
• reliable control for air damper applications with up to 10
sq ft / 44 lb-in. (5 Nm) and 20 sq ft / 88 lb-in. (10 Nm)
(seal- less damper blades; air friction-dependent).
FEATURES
• Declutch for manual adjustment
• Adjustable mechanical end limits
• Removable access cover for direct wiring
• Mountable in any orientation
• Rotation direction and service/OFF switch
SPECIFICATIONS
Supply voltage
CN6105/CN6110 24 Vac/dc -15%/+20%, 50/60 Hz
CN4605/CN4610 230 Vac -15%/+20%, 50/60 Hz
Nominal voltage
CN6105/CN6110 24 Vac/dc, 50/60 Hz
CN4605/CN4610 230Vac, 50/60 Hz
All values stated hereinafter apply to operation under
nominal voltage conditions.
Power consumption
CN6105/CN6110 5 VA / 2 W
CN4605 22 VA / 2 W at 50 Hz
CN4610 25 VA / 2 W at 60 Hz
Ambient limits
Ambient operating limits -5...+140 °F (20...+60 °C)
Ambient storage limits -22...+176 °F (-30...+80 °C)
Relative humidity 5...95%, non-condensing
Safety
Protection standard IP54
Protection class II as per EN 60730-1
Overvoltage category II
Lifetime
Full strokes 60000
Repositions 1.5 million
Mounting
Round damper shaft 3/8 in…5/8 in.
Square damper shaft 1/4 in…1/2 in.; 45° steps
Shaft length min. 1-5/8 in.
End switches (when included)
Rating Class II
Triggering points 5° / 85°
Torque rating 44 lb-in. (5Nm) / 88 lb-in. (10 Nm)
Runtime for 90°
CN6105 90 sec (dc / 60 Hz ac)
CN6110 90 sec (dc / 50 Hz ac)
CN4605 65…110 s (60/50 Hz)
CN4610 65…140 s (60/50 Hz)
Rotation stroke 95° + 3°
Dimensions see “Dimensions” on page 11
Weight (without cables) 1 lbs.
Noise rating 35 dB(A) max. at 1 m
40 dB(A) for 230 Vac at
65 sec runtime
Certification
CN6105/CN6110 CE & UL
CN4605/CN4610 CE
C
6

7. PRODUCT IDENTIFICATION SYSTEM
C-Electrical Motor
N-Fail Safe Function (Non-Spring Return)
61-24V Floating Control + ON/OFF
75-24V Modulating Control + Floating + ON/OFF
46-230V ON/OFF
05-44 lb-in. (5 Nm)
10-88 lb-in. (10 Nm)
A-Standard Model
1-No Feedback
2-Voltage Feedback Signal
0-No Internal Auxiliary Switches
2-Two Internal Auxiliary Switches
XX-System Controlled Numbers
C N 75 10 A 2 0 XX
BASIC FEATURES
Fig. 1. Setting units and control elements
Legend for Fig. 1:
1) Universal shaft adapter
2) Mechanical end limits (manually adjustable)
3) Declutch button
4) Function selection switch
5) Removable access cover
6) Anti-rotation bracket
Contents of Package
The delivery package includes the actuator, parts 1 through 6
(see Fig. 1), plus two cable grommets and a spare cable
grommet.
RUN MODES
The function selection switch (see Fig. 2) can be used to place
the actuator into any one of two different modes:
• Service/Off; or
• the floating/2-position run mode (“Dir” for CCW-closing
dampers or “Rev” for CW-closing dampers).
Fig. 2. Function selection switch
Power-Off Behavior
If power is removed, the shaft adapter remains in position.
Service/Off
If the function selection switch is set to the “Service/Off”
position, then all rotary movement is cancelled, and all
control signals are ignored, thus allowing the actuator to be
manually operated safely.
Model Description
CN6105A1011
5Nm, 24Vac/Vdc, floating control, non-spring
return, no feedback and without aux. Switch
CN4605A1001
5Nm, 230Vac, floating control, non-spring
return, no feedback and without aux. Switch
CN6110A1003
10Nm, 24Vac/Vdc, floating control, non-spring
return, no feedback and without aux. Switch
CN6110A1201
10Nm, 24Vac/Vdc, floating control, non-spring
return, no feedback and with aux. Switch
CN4610A1001
10Nm, 230Vac, floating control, non-spring
return, no feedback and without aux. Switch
CN05,CN10 SERIES DAMPER ACTUATORS FOR FLOATING/2-POSITON CONTROL
7

8. Floating/2-Position Run Mode
If the function selection switch has been set to one of the two
floating/2-position control settings—and if the actuator is wired
correspondingly (see Fig. 7, Fig. 8, and Fig. 9)—then as soon as
operating power is applied, the shaft adapter will run according to
the control signals applied.
Table 1 describes the behavior (“stops,” rotates “CCW,” or
rotates “CW”) of the CN6105/CN6110 in dependence upon the
control signals (switch “open” or “24 Vac/dc”) applied to terminals
3 and 4, the function selection switch setting, and the manner in
which the actuator is wired (either for floating mode: see Fig. 7;
or for 2-position mode: see Fig. 8).
Table 1. Behavior of CN6105/CN6110
wiring control signal at switch setting
term 3 term 4 Dir Service/ Off Rev
float. open open stops stops stops
open 24Vac/dc CCW stops CW
24Vac/dc open CW stops CCW
2-pos. 24Vac/dc open CW stops CCW
24Vac/dc 24Vac/dc CCW stops CW
Table 2 describes the behavior (“stops,” rotates “CCW,” or
rotates “CW”) of the CN4605/CN4610 in dependence upon the
control signals (switch “open” or “230 Vac”) applied to terminals 1
and 3 and the function selection switch setting: only one manner
of wiring is permitted (see Fig. 9).
Table 2. Behavior of CN4605/CN4610
control signal at switch setting
term 1 term 3 Dir Service/ Off Rev
open open stops stops stops
open 230 Vac stops stops stops
230 Vac open CW stops CCW
230 Vac 230 Vac CCW stops CW
MANUAL ADJUSTMENT
IMPORTANT
To prevent equipment damage, before manual
adjustment, you must remove power or set the func-
tion selection switch to the “Service/Off” position.
After removing power or setting the function selection switch to
the “Service/Off” position, the gear train can be disengaged using
the declutch button, permitting the shaft adapter to be manually
rotated to any position.
Limitation of Rotation Stroke
Two adjustable mechanical end limits are provided to limit the
angle of rotation as desired (see Fig. 3). The mechanical end
limits must be securely fastened in place.
Fig.3. Mechanical end limits
To ensure tight closing of the dampers, the shaft adapter has a
total rotation stroke of 95°.
INTERNAL END SWITCHES
The internal end switches “A” and “B” are changeover switches
which are activated when the shaft adapter moves past a position
of 5° and 85°, respectively (see also Table 5).
Fig.4. Internal end switch triggering points
CN05,CN10 SERIES DAMPER ACTUATORS FOR FLOATING/2-POSITON CONTROL
8

9. CN05,CN10 SERIES DAMPER ACTUATORS FOR FLOATING/2-POSITON CONTROL
9
INSTALLATION
To avoid personal injury (electrical shock) and to
prevent equipment damage, before installation, you
must remove power.
These actuators are designed for single-point mounting.
Mounting Instructions
All information and steps are included in the Installation
Instructions supplied with each actuator.
Mounting Position
The actuators can be mounted in any position (IP54 is dependent
upon orientation; see Fig. 5). Choose a mounting pKosition
permitting easy access to cables and controls.
Fig. 5. Mounting for IP54
NOTE: Further, in order to guarantee IP54, only original
Honeywell grommets may be used.
Anti-Rotation Bracket and Screws
If the actuator is to be mounted directly on a damper shaft, use
the anti-rotation bracket and screws included in the delivery
package. The min. distance between the center of the damper
shaft and the middle of the anti-rotation bracket is 3.35 in.; a
max. of 4.25 in. is allowed (see also Fig 11).
Depending upon the specifics of your mounting site, the actuator
may shift in position slightly while tightening the screws at the top
of the shaft adapter. The anti-rotation bracket features a T-piece
with a 5-mm-long shank to accommodate for this movement. It is
important to ensure that this play is not impeded.
Universal Shaft Adapter
The universal shaft adapter can be used for shafts of various
diameters and shapes (round: 3/8...5/8 in. and square:
1/4...1/2 in.).
WIRING
To avoid personal injury (electrical shock) and to
prevent equipment damage, before wiring, you
must remove power.
Access Cover
IMPORTANT
Once the access cover has been removed, please
take care to avoid damaging any of the parts now
accessible.
The access cover can be unscrewed and removed in order to
gain access to the terminal block(s) and perform wiring.
Fig. 6. Access Cover
Wiring Diagrams
Fig. 7. CN6105/CN6110 (floating mode)
! CAUTION

10. Fig. 8. CN6105/CN6110 (2-position mode)
CCW
CW
230V~
3
1
2
5
4
NL
230V ~
> 3 mm!
Fig. 9. CN4605/CN4610 (2-position mode)
Fig. 10. End switches
NOTE: Both internal end switches must be connected to the
same power source.
Tables 3,4 and 5 summarize the information presented in the
preceding wiring diagrams.
Table 3. Signals at terminals for CN6105/CN6110
ter-
minal
signal in floating signal in 2-pos. mode
2 common ~/- common ~/-
3 24 V ~/+
(control signal)
24 V ~/+
(control/ power signal)
4 24 V ~/+
(control signal)
24 V ~/+
(control signal/power)
NOTE: All cables connected to these terminals must be
equipped with spark suppression.
Table 4. Signals at terminals for CN4605/CN4610
terminal signal
1 L (230 V ~)
2 N (230 V ~)
3 control signal
NOTE: All cables connected to these terminals must be
equipped with spark suppression.
Table 5. Internal end switches (SSW2)
terminal type of switch
S1 common lead for switches A and B
S2 / S3
change-over switch A (S1/S2 opens and
S1/S3 closes when shaft adapter moves CW
past 5°; reverts to original state when shaft
adapter moves CCW past 5°).
S5 / S6
change-over switch B (S1/S5 opens and
S1/S6 closes when shaft adapter moves CW
past 85°; reverts to original state when shaft
adapter moves CCW past 85°).
CN05,CN10 SERIES DAMPER ACTUATORS FOR FLOATING/2-POSITON CONTROL
10

11. DIMENSIONS
Fig. 11. Dimensions (in in.)
CN05,CN10 SERIES DAMPER ACTUATORS FOR FLOATING/2-POSITON CONTROL
11

12. CN20, CN34 SERIES
NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS
FOR FLOATING / 2-POSITION CONTROL
PRODUCT DATA
GENERAL
These direct-coupled damper actuators provide two-position
and floating control for:
air dampers,
VAV units,
air handlers,
ventilation flaps,
louvers, and
reliable control for air damper applications with up to
4.6 m2
/ 50 sq.ft. (20 Nm / 177 lb-in) or 7.8 m
2
/ 85 sq. ft.
(34 Nm / 300 lb-in) (seal-less dampers; air friction-
dependent).
FEATURES
Self-centering shaft adapter
Access cover to facilitate connectivity
Service/off for safe & easy servicing
Rotation direction selectable by switch
Declutch for manual adjustment
Mechanical end limits
Field-installable auxiliary switches
Mountable in any orientation (no IP54 if upside down)
Mechanical position indicator
CE and UL certified (230V models with CE only)
SPECIFICATIONS
Supply voltage
CN6120/CN6134 24 Vac/dc 15%, 50/60 Hz
CN4620/CN4634 230 Vac 15%, 50/60 Hz
Nominal voltage
CN6120/CN6134 24 Vac/dc, 50/60 Hz
CN4620/CN4634 230 Vac, 50/60 Hz
All values stated hereinafter apply to operation under
nominal voltage conditions.
Power consumption
CN6120 6 VA / 3 W
CN4620 8 VA / 3 W
CN6134 6 VA / 3 W
CN4634 10 VA / 4 W
Ambient limits
Ambient operating limits -20...+60 C (-5...+140 °F)
Ambient storage limits -40...+80 C (-40...+175 °F)
Relative humidity 5...95%, non-condensing
Safety
Protection standard IP54 as per EN 60529
Protection class II as per EN 60730-1
Overvoltage category III
Lifetime
Full strokes 60000
Repositions 1.5 million
Mounting
Round damper shaft 10...27 mm (3/8...1-1/16")
Square damper shaft 10...18 mm (3/8...11/16");
spets°54
Shaft length min. 22 mm (7/8")
End switches (when included)
Rating 5 A (resistive) / 3 A (inductive)
Triggering points 5 / 85
Torque rating
CN6120 / CN4620 20 Nm (177 lb-in)
CN6134 / CN4634 34 Nm (300 lb-in)
Runtime 95 sec (60 Hz) / 110 sec (50 Hz
or DC supply)
Rotation stroke 95 3
Dimensions see "Dimensions" on page 17
Weight (without cables) 1.35 kg (3 lbs.)
Noise rating 40 dBA max. at 1 m
Certification CE CN6120 / CN6134
CN4620 / CN4634
UL CN6120 / CN6134
12
C

13. CN20, CN34 SERIES DAMPER ACTUATOR FOR FLOATING AND 2-POS CONTROL
MODELS
Description#Model
CN6120A1002 20Nm,24Vac/Vdc, Floating/2-position control, Non-Spring Return, No feedback and without aux. Switch
CN4620A1001 20Nm,230V,Floating/2-position control, Non-Spring Return, No feedback and without aux. Switch
CN6134A1003 34Nm,24Vac/Vdc, Floating/2-position control, Non-Spring Return, No feedback and without aux. Switch
CN4634A1001 34Nm,230Vac, Floating control/2-position, Non-Spring Return, No feedback and without aux. Switch
Product Identification System
C – Direct Coupled Actuator
N – Fail Safe Function (Non-Spring Return)
61 – 24V Floating/2-position Control
72 – 24V Modulating and Floating/2-position Control
46 – 230V Floating/2-position Control
20 – 20 Nm (177 lb-in)
34 – 34 Nm (300 lb-in)
A – Standard Model
1 – No Feedback
2 – Voltage Feedback Signal
0 – No Internal Auxiliary Switches
2 – Two Internal Auxiliary Switches
XX – System Controlled Numbers
C N 61 20 A 1 0 XX
Fig. 1. Product Identification System
OPERATION / FUNCTIONS
Fig. 2. Setting units and control elements
Legend for Fig. 2:
1 Self-centering shaft adapter
2 Retainer clip
3 Rotational angle scales (0...90° / 90...0°)
4 Mechanical end limits
5 Declutch button
6 Anti-rotation bracket
7 Function selection switch
8 Access cover
Contents of Package
The delivery package includes the actuator itself, parts 1
through 8 (see Fig.2), the anti-rotation bracket screws, and
installation instruction.
RUN MODES
The function selection switch (see Fig. 3) can be used to
place the actuator into any one of three different modes:
Dir, floating/2-position control, cw run.
Service/Off, actuator stop running.
Rev, floating/2-position control, ccw run.
1
2
3
4
5
6
87
13

14. CN20, CN34 SERIES DAMPER ACTUATOR FOR FLOATING AND 2-POS CONTROL
Fig. 3. Function selection switch
Power-Off Behavior
If power is removed, the actuator retains its position.
Service/Off
If the function selection switch is set to the "Service/Off"
position, all rotary movement is cancelled, and all control
signals are ignored, thus allowing the actuator to be safely
manually operated.
Floating/2-Position Run Mode
If the function selection switch has been set to one of the two
floating/2-position control settings (Dir or Rev) and the
actuator is wired correspondingly (see A1 and A2) as soon as
the operating power is applied, the actuator will run according
to the power applied
Table 1 describes the behavior (stops, rotates CCW, or
rotates CW) of the CN6120/CN6134 in relation to the control
signals (switch "open" or "24Vac/dc") applied to terminals 3
and 4, the function selection switch setting, and the manner in
which the actuator is wired (either for floating mode: see A1,
or for 2-position mode: see A2).
Table 1. Behavior of CN6120/CN6134
Control signal at Function selection switchWiring
term. 3 term. 4 Dir Service/Off Rev
open open stops stops stops
open 24Vac/dc CCW stops CWFloat.
24Vac/dc open CW stops CCW
24Vac/dc open CW stops CCW
2-pos.
24Vac/dc 24Vac/dc CCW stops CW
Table 2 shows the same actuator behavior as Table 1, but for
CN4620/CN4634 (230Vac models).
Table 2. Behavior of CN4620/CN4634
Control signal at Function selection switchWiring
term. 3 term. 4 Dir Service/Off Rev
open open stops stops stops
open 230Vac CCW stops CWFloat.
230Vac open CW stops CCW
230Vac open CW stops CCW
2-pos.
230Vac 230Vac CCW stops CW
Sleep Mode
When actuator reaches end stop or any obstacles blocking its
running, it will fall into sleep mode automatically. Actuator will
periodically start up and try to resume running, which will save
energy significantly through whole service life.
Position Indication
The hub adapter indicates the rotation angle position by
means of the rotational angle scales (0...90° / 90...0°)
provided in the actuator plate (see Fig. 4).
Fig. 4. Position indication
Manual Adjustment
IMPORTANT
To prevent equipment damage, you must remove
power or set the rotation direction switch to the
"Service/Off" position before manual adjustment.
After removing power or setting the rotation direction switch to
the "Service/Off" position, the gear train can be disengaged
using the declutch button, permitting the actuator shaft to be
manually rotated to any position.
Limitation of Rotation Stroke
Two adjustable mechanical end limits (adjustable in 5°
increments) are provided to limit the angle of rotation as
desired (see Fig. 5).
Fig. 5. Mechanical end limits
The mechanical end limits must be securely fastened in place.
It is important that they properly mesh with the rotational
angle scales when the screws are tightened.
Internal End Switches
NOTE: Applicable to models with internal switches only.
14
!

15. CN20, CN34 SERIES DAMPER ACTUATOR FOR FLOATING AND 2-POS CONTROL
The internal end switches are set to switch from "common" to
"normally open" at angles of 5° and 85°, respectively, from the
totally counterclockwise position.
-2.5
85 80 5 590 092.5 51015
CCW internal
end switch
CW internal
end switch
actuator scale: clockwise
end switch scale
actuator scale: counterclockwise
Fig. 6. Internal end switch triggering points
INSTALLATION
These actuators are designed for single-point mounting.
In order to prevent equipment damage, you must
remove power or set the rotation direction switch to the
"Service/Off" position before manual operation.
Mounting Instructions
All information and steps are included in the installation
instructions supplied with the actuator.
Mounting Position
The actuators can be mounted in any position (no IP54 if
mounted upside down; see Fig. 7). Choose a mounting posi-
tion permitting easy access to the actuator's cables and
controls.
IP54 IP54IP54 IP54
Fig. 7. Mounting for IP54
Mounting Bracket and Screws
If the actuator is to be mounted directly on a damper shaft,
use the mounting bracket and screws included in the delivery
package.
Self-Centering Shaft Adapter
The self-centering shaft adapter can be used for shafts
having various diameters (10...27 mm [3/8...1-1/16"]) and
shapes (square or round).
In the case of short shafts, the shaft adapter may be reversed
and mounted on the duct side.
Stroke Limitation with Mechanical End Limits
The mechanical end limits enable the stroke to be limited
from 0...90° in increments of 5°.
Wiring
Connecting to the Power Supply
In order to comply with protection class II, the power source of
24 V actuators must be reliably separated from the network
power supply circuits as per DIN VDE 0106, part 101.
Access Cover
To facilitate wiring the actuator to the controller, the access
cover can be detached from the actuator.
Remove power before detaching the access cover.
Once the access cover has been removed, please
take care to avoid damaging any of the parts now
accessible.
Fig. 8. Access cover (models with internal switches)
Depending upon the model, the access cover may have one
or two terminal strips, including a layout with a description for
each of the terminals.
Fig. 9. Actuator with access cover removed
(models with internal switches)
15
IMPORTANT!
IMPORTANT!

16. CN20, CN34 SERIES DAMPER ACTUATOR FOR FLOATING AND 2-POS CONTROL
Wiring diagrams
A1 CN6120,CN4620
CN6134,CN4634 FLOATING
A2 CN6120,CN4620
CN6134,CN4634 2-POS
A3 END SWITCHS
(models with switch only)
NOTE: Internal end switches S1 and S4 must be connected to the same power source.
Below 2 tables summarize the information presented in the preceding wiring diagrams.
Wiring
Models Terminal
Floating 2-position
2 common / common /
3 24V ~/+ (clockwise) 24V ~/+
CN6120,CN6134
supply and signal lines
(must be equipped with spark suppressors) 4 24V ~/+ (counterclockwise) 24V ~/+ control signal
2 common / common /
3 230Vac (clockwise) 230Vac
CN4620,CN4634
supply and signal lines
(must be equipped with spark suppressors) 4 230Vac (counterclockwise) 230Vac control signal
Connecting cable Terminal Description
S1 common
S2 normally closedCCW (left) 5°
S3 normally open
S4 common
S5 normally closed
end switches
(models with internal
switches only)
CW (right) 85°
S6 normally open
OPTIONAL ACCESSORIES
The following optional accessories can be ordered separately.
Auxiliary Switch Kit
Order no.: SW2
S1
S2
S3A
B
S4
S5
S6 C
D45
0
90
90
0
A
B
C
D
The auxiliary switches are field-installable parts providing
two SPDT freely-adjustable switches.
SPARE PARTS
Spare Parts Kit
Order no.: A7209.2071
The spare parts kit contains the following items:
Anti-rotation bracket and screws
Access cover screw
Plastic protective cap for protection standard IP54
Mechanical end limit screw and retainer
Anti-Rotation Bracket Kit
Order no.: A7209.2073
The anti-rotation bracket kit can be ordered separately.
Contains:
10 anti-rotation brackets
20 screws
16

17. CN20, CN34 SERIES DAMPER ACTUATOR FOR FLOATING AND 2-POS CONTROL
DIMENSIONS
17

18. CS05, CS10, CS20 Series
Spring Return Direct Coupled Actuators
CS4105, CS4110, CS4120, CS7505, CS7510, CS7520, CS8105,
CS8110, CS8120
PRODUCT DATA
FEATURES
APPLICATION
CS41XX, CS75XX, CS81XX Spring Return Direct Coupled
Actuators (DCA) are used within heating, ventilating, and air-
conditioning (HVAC) systems. They can drive a variety of
quarter-turn, final control elements requiring spring return fail-
safe operation.
Applications include:
• Volume control dampers, mounted directly to the drive
shaft or remotely (with the use of accessory hardware).
• Quarter-turn rotary valves, such as ball or butterfly valves
mounted directly to the drive shaft.
• Linear stroke globe or cage valves mounted with linkages
to provide linear actuation.
• Brushless DC submotor with electronic stall protection
for floating/modulating models.
• Brush DC submotor with electronic stall protection for
2-position models.
• Self-centering shaft adapter (shaft coupling) for wide
range of shaft sizes.
• Models available with three torque ratings:
44 lb-in. (5 N•m), 88 lb-in. (10 N•m),
and 175 lb-in. (20 N•m).
• Models available for use with two-position, single pole
single throw (spst), line-voltage or low-voltage
controls.
• Models available for use with floating or switched
single-pole, double-throw (spdt) controls.
• Models available for use with proportional current or
voltage controls.
• Models available with combined floating/modulating
control in a single device.
• Models available with adjustable zero and span.
• Models available with line-voltage internal and
switches.
• Access cover to facilitate connectivity.
• Metal housing with built-in mechanical end limits.
• Spring return direction field-selectable.
• Shaft position indicator and scale.
• Manual winding capability with locking function.
• UL (cUL) listed and CE compliant.
• All Models are plenum-rated per UL873.
18
C

19. M20952
SPECIFICATIONS
Models: See Tables 2, 3 and 4.
Dimensions: See Fig. 1.
Device Weight: 7 lb (3.2 kg).
Timing (At Rated Torque and Voltage):
Drive Open (typical):
Floating, Modulating Models: 90 seconds.
Two-Position Models: 45 seconds ±5 seconds.
Spring Close: 20 seconds typical.
3-15/16 (100)
Temperature Ratings: 1-9/16 1-9/16
Ambient: -40°F to 140°F (-40°C to 60°C).
Shipping and Storage: -40°F to 158°F (-40°C to 70°C).
Humidity Ratings: 5% to 95% RH noncondensing.
Electrical Connections:
Field wiring 14 to 22 AWG (2.0 to 0.344 mm sq) to screw
terminals, located under the removable access cover.
(40) (40)
1-9/16
(40)
2-1/2
(64)
MIN.
3(76)
MIN.
FROM
SHAFT
END
Electrical Ratings: See Table 1.
End Switches (Two SPDT):
Settings (fixed): 7° nominal stroke, 85° nominal stroke.
Ratings (maximum load):
Low-Voltage Models: 250 VAC, 5A resistive, 3A inductive.
Line-Voltage Models: 250 VAC, 5A resistive.
Mounting: Self-centering shaft adapter (shaft coupling).
Round Damper Shafts: 0.375 to 1.06 in. (10 to 27 mm).
Square Damper Shafts: 1/2 to 3/4 in. (13 to 19 mm).
Actuator can be mounted with shaft in any position.
NOTE: For 175 lb-in. (20 N•m) models: 3/4 in. or greater
shaft diameter recommended.
Minimum Damper Shaft Length: 1 in. (25 mm); 3 in.
(76 mm) recommended.
1/4 (6)
9-3/4
(247)
6-1/8
(156)
3 (76)
MIN.
2-15/16 (75)
Fig. 1. Dimensional drawing of actuator in in. (mm).
Table 1. Electrical Ratings.
Power Input Power Consumption (VA)
44 lb-in. (5 N•m) 88 lb-in. (10 N•m) 175 lb-in. (20 N•m)
Model(s) Voltage Frequency Driving Holding Driving Holding Driving Holding
Floating, Modulating 24 VAC±20% (Class 2), 24 VDC 50/60 Hz. 13 5 14 5 16 5
Two-Position, Low-voltage 24 VAC±20% (Class 2), 24 VDC 50/60 Hz. 25 8 30 8 40 8
Two-Position, Line-voltage 100-250 VAC 50/60 Hz. 45 13 45 13 60 13
ORDERING INFORMATION
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory).
2. Honeywell ECC Customer Care
35F., Tower A, City Center 100 Zun Yi Road
Shanghai 200051 China Tel: (86-21) 5257 4568
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Finland, France, Germany,
Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, P.R.C.
19
CS05, CS10,CS20 SERIES SPRING RETURN DIRECT COUPLED ACTUATORS

20. Model Description
CS4105A1002 100-250 VAC Two-Position Control; Reversible Mount;
5N•m; Standard U.S Model; No Feedback; No End
Switches;
CS4110A1002 100-250 VAC Two-Position Control; Reversible Mount;
10N•m; Standard U.S Model; No Feedback; No End
Switches;
CS4110A1200 100-250 VAC Two-Position Control; Reversible Mount;
10N•m; Standard U.S Model; No Feedback; Two End
Switches;
CS4120A1001 100-250 VAC Two-Position Control; Reversible Mount;
20N•m; Standard U.S Model; No Feedback; No End
Switches;
CS4120A1209 100-250 VAC Two-Position Control; Reversible Mount;
20N•m; Standard U.S Model; No Feedback; Two End
Switches;
CS7505A2008 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 5N•m; Standard U.S Model; Voltage Feedback
Signal; No End Switches;
CS7510A2008 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 10N•m; Standard U.S Model; Voltage Feedback
Signal; No End Switches;
CS7510A2206 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 10N•m; Standard U.S Model; Voltage Feedback
Signal; Two End Switches;
CS7510H2209 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 10N•m; Selectable control signal; Adjustable zero
and span; Includes service and atuo-adapt modes; Voltage
Feedback Signal; Two End Switches;
CS7520A2007 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 20N•m; Standard U.S Model; Voltage Feedback
Signal; No End Switches;
CS7520A2205 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 20N•m; Standard U.S Model; Voltage Feedback
Signal; Two End Switches;
CS7520H2208 24 VAC/VDC Modulating and Floating Control; Reversible
Mount; 20N•m; Selectable control signal; Adjustable zero
and span; Includes service and atuo-adapt modes; Voltage
Feedback Signal; Two End Switches;
CS8105A1008 24 VAC/VDC Two-Position Control; Reversible Mount;
5N•m; Standard U.S Model; No Feedback; No End
Switches;
CS8110A1008 24 VAC/VDC Two-Position Control; Reversible Mount;
10N•m; Standard U.S Model; No Feedback; No End
Switches;
CS8110A1206 24 VAC/VDC Two-Position Control; Reversible Mount;
10N•m; Standard U.S Model; No Feedback; Two End
Switches;
CS8120A1007 24 VAC/VDC Two-Position Control; Reversible Mount;
20N•m; Standard U.S Model; No Feedback; No End
Switches;
CS8120A1205 24 VAC/VDC Two-Position Control; Reversible Mount;
20N•m; Standard U.S Model; No Feedback; Two End
Switches;
Table 2. O.S. Number Selection (see Table 3 also).
C Motorized Actuator
S Fail Safe Function (Spring Return)
41 100-250 VAC Two-Position Control; Reversible Mount
75 24 VAC/VDC Modulating and Floating Control; Reversible Mount
81 24 VAC/VDC Two-Position Control; Reversible Mount
05 44 lb-in. (5 N•m)
10 88 lb-in. (10 N•m)
20 175 lb-in. (20 N•m)
Aa Standard U.S. Model
Bb Standard European Model
Eb
Ha
Selectable control signal; Adjustable zero and span;
Includes service and auto-adapt modes
1 No Feedback
2 Voltage Feedback Signal
0 No End Switches
2 Two End Switches
X X System Controlled Numbers
C S 7
a
Model manufactured for sale in the United States.
b
Model manufactured for sale in Europe.
Table 4. Available Model
Table 3. Actuator Catalog Numbering (see Table 2 also).
S Spring Return Fail Safe Mode
N Non-Spring Return Fail Safe Mode
05 44 lb-in. (5 N•m); Spring Return Only
10 88 lb-in. (10 N•m); Spring Return Only
20 175 lb-in. (20 N•m)
34 300 lb-in. (34 N•m); Non-Spring Return Only
24 24 VAC/VDC Floating Control
24-2POS 24 VAC/VDC Two-Position Control
120-2POS 120 VAC Two-Position Control
230-2POS 230 VAC Two-Position Control
010 24 VAC/VDC Modulating and Floating Control
Fixed Zero/Span, No End Switches
-SW2 Internal End Switches
-SERa Enhanced Modulating; Adjustable Zero/Span
S 10 24-2POS -SW2
a
Enhanced models include two internal end switches.
20
CS05, CS10,CS20 SERIES SPRING RETURN DIRECT COUPLED ACTUATORS

21. Stroke: 95° ±3°, mechanically limited.
Design Life (at Rated Voltage):
Two-position models: 50,000 full stroke cycles;
50,000 full stroke spring returns.
Floating and Modulating models: 60,000 full stroke cycles;
1,500,000 repositions; 60,000 full stroke spring returns.
Controller Type:
S05, S10, S20: See Table 3.
S05, S10, S20: Modulating or Floating; controlled by selector
switch.
Input Impedance: 95K ohms minimum.
Feedback Signal: 0-10 VDC or 2-10 VDC;
Driving current is 3 mA minimum.
Torque Ratings:
Typical Holding, Driving, Spring Return:
S05: 44 lb-in. (5 N•m).
S10: 88 lb-in. (10 N•m).
S20: 175 lb-in. (20 N•m).
Stall Maximum (fully open at 24°C):
S05: 100 lb-in. (11.3 N•m).
S10: 200 lb-in. (22.6 N•m).
S20: 350 lb-in. (39.6 N•m).
Noise Rating at 1m (Maximum):
Holding: 20 dBA (no audible noise).
Two-position models:
Driving: 50 dBA.
Spring Return: 65 dBA.
Floating and Modulating models:
Driving: 40 dBA.
Spring Return: 50 dBA.
Environmental Protection Ratings:
NEMA2 (US Models) or IP54 (European Models) when
mounted on a horizontal shaft with access cover below the
shaft.
Approvals: See Table 5.
Table 5. Approvals.
UL/cUL
UL873 Plenum Rating,
File No. E4436; Guide No. XAPX.
CE
C-TICK
Accessories:
32004254-002 Self-Centering Shaft Adapter (supplied with
actuator).
50030966-001 Anti-Rotation Bracket (supplied with actuator).
6174215 Extension Screw (supplied with actuator).
27518 Balljoint (5/16 in.).
103598 Balljoint (1/4 in.).
205860 Electronic Minimum Position Potentiometer.
27520A-E,G,H-L,Q Pushrod (5/16 in. diameter).
5450074 Water-tight Cable Gland/Strain-relief Fitting
(supplied with actuator).
32003036-001 Weather Enclosure.
50001194-001 Foot Mount Kit.
50005859-001 NEMA4/4X Enclosure.
SW2-US Auxiliary Switch Package.
See also Form 63-2620.
Sizing
Required Torque
In lieu of data from a Specification Engineer or Manufacturer,
required torque for a given damper load can be determined
using the following method:
Where:
— TR = Required torque for the damper load.
— TD = Damper torque rating from the manufacturer,
expressed in either (lb-in.)/(sq ft) or (N•m)/(sq m). the
damper load.
— AD = Damper area expressed in either sq ft or sq m.
Actuators Required
In lieu of data from a Specification Engineer or Manufacturer,
the number of required actuators for a given damper load
can be determined using the following method:
Where:
N = Number of actuators.
— TR = Required torque for the damper load. (See above.)
— TA = Actuator torque rating.
— SF = Safety factor.
NOTE: The safety factor accounts for variables such as
mis- alignments, aging of the damper, etc. 0.8 is a
typical safety factor.
T FS
T
N
A
R
DDR ATT
21
CS05, CS10,CS20 SERIES SPRING RETURN DIRECT COUPLED ACTUATORS

22. PRODUCT DATA
APPLICATION
The MS4104, MS4109, MS4604, MS4609, MS8104, MS8109
Fast-Acting, Two-Position Actuators are spring return direct
coupled actuators (DCA) with an integral junction box for on/
o damper control. The actuator accepts an on/o signal from
a single-pole, single-throw (spst) controller. Reversible
mounting allows actuator to be used for either clockwise (cw)
or counterclockwise (ccw) spring return and are designed to
operate reliably in smoke control systems requiring
FEATURES
• 30 lb-in. (3.4 N•m) or 80 lb-in. (9 N•m) minimum driving
torque at 350 °F (176 °C).
• Reversible mounting facilitates use in either clockwise
(cw) or counterclockwise (ccw) spring rotation.
• Integral spring return ensures level of return torque.
• Stainless steel internal spring.
• Fifteen-second spring return timing.
• No special cycling required during long-term holding.
• No audible noise during holding.
• Patent pending design eliminates need for limit
switches to reduce power consumption.
• Models available for 24, 120 and 230 Vac.
• N degree angle of rotation.
• Actuator holds rated torque at reduced power level.
• Die-cast aluminum housing.
• Housing design allows ush mounting to damper.
• Designed to operated reliably in smoke control
systems requiring Underwriter's Laboratories Inc.
UL555S rating up to 350F.
• Models available with SPST position-indicating
switches (7°, 85° stroke).
Fire and Smoke Damper Actuator
MS4104, MS4109, MS4604, MS4609, MS8104, MS8109
Fast-Acting, Two-Position Actuators FOR FIRE/SMOKE CONTROL APPLICATIONS
Wiring:
Fig. 1. Typical 24 Vac wiring.
Fig. 2. Typical 120 Vac wiring.
M34624
24 VAC
BLACK
RED
L1 ( )
L2 ( )
YELLOW
YELLOW
BLUE
7° AUXILIARY
SWITCH
85° AUXILIARY
SWITCH
BLUE
WHITE
BLACK
GREEN
L1 ( )
L2 ( )
YELLOW
YELLOW
BLUE
BLUE
7° AUXILIARY
SWITCH
85° AUXILIARY
SWITCH
120 VAC
M34625
Fig. 3. Typical 230 Vac wiring.
Dimensions:
M34626
BLUE
BROWN
GREEN
230 VAC
L1 ( )
L2 ( )
YELLOW
YELLOW
BLUE
BLUE
7° AUXILIARY
SWITCH
85° AUXILIARY
SWITCH
M34622
2 (51)
1 (25)
90°
0°
11/16
(17)
6-3/8
(161)
8-15/16
(227)
4 (102)
2 (51) 1/16
(2)
3-1/4 (83)
5-1/8 (130)
9/16 (14)
22
N314

23. MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 FAST-ACTING, TWO-POSITION ACTUATORS
Model
Voltage
(Vac)
Internal
Auxiliary
Switches
Torque
in lb-in.
(N•m)
MS4104F1010
120
120 30 (3.4)None
None
None
None
None
None
MS4104F1210 2 SPST
a
2 SPST
a
2 SPST
a
2 SPST
a
2 SPST
a
2 SPST
a
30 (3.4)
120
120
320
320
80 (9)
80 (9)
30 (3.4)
30 (3.4)
320 80 (9)
320 80 (9)
24 30 (3.4)
24 30 (3.4)
24 80 (9)
24 80 (9)
MS4109F1010
MS4109F1210
MS4604F1010
MS4604F1210
MS4609F1010
MS4609F1210
MS8104F1010
MS8104F1210
MS8109F1010
MS8109F1210
SPECIFICATIONS
Models:
a
Internal switches are designed to pass UL555S
requirements (at 350 °F for 30 minutes) and are intended for
use as position indication.
Electrical Ratings:
Power Input:
MS4104F, MS4109F: 120 Vac ±10%, 60 Hz.
MS4604F, MS4609F: 230 Vac ±10%, 50/60 Hz.
MS8104F, MS8109F: 24 Vac +20%, -10%, 50/60 Hz.
Power Consumption:
MS4104F: Running: 0.18A, 18W. Holding: 0.11A, 9W
MS4109F: Running: 0.25A, 23W. Holding: 0.13A, 7W
MS4604F: Running: 0.13A, 18W. Holding: 0.10A, 11W
MS4609F: Running: 0.13A, 23W. Holding: 0.09A, 7W
MS8104F: Running: 16VA. Holding: 8 VA
MS8109F: Running: 23VA. Holding: 7 VA
Electrical Connections:
Power Lead Wires:
MS410xF and MS460xF: 32 inches (0.8m), 18 AWG
MS810xF: 39 inches (1m), 18 AWG
Switch Lead Wires: 18 inches, 18 AWG, 2 color coded leads.
Controller Type:
MS4104, MS4109: Line voltage (120 Vac), two-position, spst
(Series 40).
MS4604, MS4609: Line voltage (230 Vac), two-position, spst
(Series 40).
MS8104, MS8109: Low voltage (24 Vac), two-position, spst
(Series 80).
Device Weight:
5 lb (2.3 kg).
Noise Rating (Maximum):
Driving Open: 75 dBA at 1m.
Holding: 20 dBA at 1m (no audible noise).
Temperature Ratings:
Ambient: 0°F to 130°F (-18°C to 55°C).
Shipping and Storage: -40°F to 140°F (-40°C to 60°C).
IMPORTANT
The actuator is designed to meet UL555S standards
at 350°F (176°C). The actuator must be tested with
the damper to achieve this rating.
Humidity Ratings:
5% to 95% RH noncondensing.
Stroke:
95° ± 3°, mechanically limited.
Torque Rating (at rated voltage):
Spring Return:
MS4104F, MS4604F, MS8104F: 30 lb-in. (3.4 N•m).
MS4109F, MS4609F, MS8109: 80 lb-in. (9 N•m).
Stall Maximum:
MS4104F, MS4604F, MS8104F: 150 lb-in. (17 N•m).
MS4109F, MS4609F, MS8109: 240 lb-in. (27 N•m).
350°F Driving:
MS4104F, MS4604F, MS8104F: 30 lb-in. (3.4 N•m).
MS4109F, MS4609F, MS8109: 80 lb-in. (9 N•m).
Timing (At Rated Torque and Voltage):
Drive Open: 15 seconds typical.
Spring Close: 15 seconds typical.
Design Life (at Rated Voltage):
30,000 full stroke cycles.
Cycling Requirements:
The actuator and the internal spring are designed to require
no special cycling during long-term holding.
Honeywell recommends following all local, state and national
codes for periodic testing of the entire smoke control sys-
tem. Refer to National Fire Protection Association (NFPA)
National Fire Codes®: NFPA90A, NFPA92A and NFPA92B
for your application.
NFPA recommends periodic examination of each fire/smoke
damper (semi-annually or annually) to ensure proper per-
formance.
Minimum Damper Shaft Length:
2 in. (51 mm).
Mounting:
Round 1/2 inch shaft adapter with 1/4 inch set screws.
Threads: ¼-20 UNC-2A
Material: Alloy Steel hardened to HRC 45-53
Thread Lock: Nylon Patch
IMPORTANT
Honeywell does not recommend using linkages with
these actuators because si de-loading of the output
hub reduces actuator life.
Environmental Protection Ratings:
NEMA, IP40.
Accessories:
205649 Mounting Bracket (not supplied with actuator).
Approvals:
MS4104F,
MS4109F
MS4604F,
MS4609F
MS8104F,
MS8109F
UL/cUL X X X
UL60730 X X X
CE X X X
C-Tick X X X
23

24. H A O P H U O N G - T H I N K T O G E T H E R
Head office:
Address: 7/31 Song Than Business
Center, Di An, Binh Duong, Vietnam.
Tel: 84-650-3737-619
Fax: 84-650-3737-620
Ha Noi office:
Address: 16/6/102 Nguy Nhu Kon Tum
Nhan Chinh, Thanh Xuan, Hanoi.
Tel: 84-4-3568-3740
Fax: 84-4-3568-3741
Cambodia office:
Address: Office S2 Second Floor Left. Blue
Green Service Office Space & Apartment.
13A, St 81 (Wat Koh) Boeung Raing, PP.
Tel: 855-2322-3635 - Fax: 855-2322-3645