2. What is VLSI?
Acronym of VLSI
– Very-Large-Scale Integration
A VLSI contains more than a million or so
switching devices or logic gates
Early in the first decade of the 21st century, the
actual number of transistors has exceeded 100
million
3. Why should Make Ics?
Integration improves
– size
– speed
– power
Integration reduce manufacturing costs
– (almost) no manual assembly
4. Integrated Circuits Trends
An entire circuit is manufactured in a single piece of silicon,
first appeared around 1960
At that time only a few simple gates offering primitive logic
functions such as not, nand, nor etc. could be accommodated
(SSI)
By 1970 MSI circuits with about a thousand transistors
appeared
By 1980 LSI circuits of approximately one hundred
thousand devices were possible
5. IC Evolution
SSI – Small Scale Integration (early 1970s)
– contained 1 – 10 logic gates
MSI – Medium Scale Integration
– logic functions, counters
LSI – Large Scale Integration
– first microprocessors on the chip
VLSI – Very Large Scale Integration
– now offers 64-bit microprocessors,
complete with cache memory (L1 and often L2),
floating-point arithmetic unit(s), etc.
7. Why need Choice of Technology?
Two distinct types of technology are fabricated in silicon based upon
– BJT (Bipolar Junction Transistor)
– MOS (Metallic Oxide Semiconductor)
Since processing of these technologies is very different, it is impractical
to mix them up within a chip.
MOS logic occupies much smaller area of silicon than the equivalent
BJT logic.
MOS technology has a much higher potential packing density.
A MOS logic circuit requires appreciably less current and hence less
power than its bipolar counter part.
However, bipolar circuits operate faster than MOS circuits
8. Choice of MOS and BJT
Even so, the speed-power product for MOS logic compares favorably
with that of BJT logic.
The structure of an MOS transistor is much simpler than that of bipolar
devices and this makes manufacturing process easier
This in turn should result in fewer faults occurring in fabrication (high
yield)
Dynamic logic circuits cannot be implemented in bipolar technology
Thus in terms of area, power dissipated, yield and flexibility MOS
technology is superior to BJT
9. Moore’s Law
Gordon Moore cofounder of Intel Corporation
visualized in the 1970’s that chip building
technology would improve very quickly
He projected that the number of transistors on a chip
would double about every 18 months
10. EVIDENCE OF MOORE’S LAW
ACCORDING TO GORDEN MOORE -
(in millions)
1996 MID 1997 1999
YEAR
5 10 20 40
MID 2001
Pentium-I Came In 1996 Transistor Count – 5 Million
Pentium-IV Came In 2001 Transistor Count – 43 Million
11. Design Methodology
Top-down design
- Realizing the desired complex behavior of a H/W by
partioing it into an interconnect of simpler subbehavior
- Create lower levels of abstraction from upper levels.
Bottom-up design
-Aims at realizing the desired complex behavior by suitable
selection and interconnection of parts/components from an
available set of parts/components with known behavior.
- Creates abstractions from low-level behavior.
Good design needs both top-down and bottom-up efforts.
14. Structured Design Principles
Hierarchy:
“Divide and conquer” technique involves dividing a module into sub-
modules and then repeating this operation on the sub-modules until the
complexity of the smaller parts becomes manageable.
Regularity:
The hierarchical decomposition of a large system should result in not
only simple, but also similar blocks, as much as possible.
Regularity usually reduces the number of different modules that need to
be designed and verified, at all levels of abstraction.
15. Structured Design Principles
Modularity:
The various functional blocks which make up the larger system must
have well-defined functions and interfaces.
Locality:
Internal details remain at the local level. The concept of locality also
ensures that connections are mostly between neighboring modules,
avoiding long-distance connections as much as possible.
16. VLSI design process
Major levels of abstraction:
– specification;
– architecture;
– logic design;
– circuit design;
– layout.
18. VLSI Design Cycle
System Specification
Specification of the size, speed, power and functionality of the VLSI
system.
Architectural Design
Decisions on the architecture, e.g., RISC/CISC, # of ALU’s, pipeline
structure, cache size, etc. Such decisions can provide an accurate
estimation of the system performance, die size, power consumption, etc.
19. VLSI Design Cycle
Functional Design
Identify main functional units and their interconnections. No details of
implementation.
20. VLSI Design Cycle
Logic Design
Design the logic, e.g., boolean expressions, control flow, word width,
register allocation, etc. The outcome is called an RTL (Register Transfer
Level) description. RTL is expressed in a HDL (Hardware Description
Language), e.g., VHDL and Verilog.
X = (AB+CD)(E+F)
Y= (A(B+C) + Z + D)
21. VLSI Design Cycle
Circuit Design
Design the circuit including gates, transistors, interconnections, etc. The
outcome is called a netlist.
22. VLSI Design Cycle
Physical Design
Convert the netlist into a geometric representation. The outcome is called
a layout.
23. VLSI Design Cycle
Fabrication
Process includes lithography, polishing, deposition, diffusion, etc., to
produce a chip.
Packaging
Put together the chips on a PCB (Printed Circuit Board) or an MCM
(Multi-Chip Module)
24. VLSI Design Cycle
System Specification
Architectural
Specification
RTL in HDL
Netlist
Layout
Timing & relationship
between functional units
Chips
Packaged and
tested chips
Architectural
Design
Functional
Design
Logic
Design
Physical
Design
Fabrication
Packaging
Circuit Design
or
Logic Synthesis
26. Physical Design Cycle (2/6)
Circuit Partitioning
Partition a large circuit into sub-circuits (called blocks). Factors like
#blocks, block sizes, interconnection between blocks, etc., are
considered.
27. Physical Design Cycle (3/6)
Floorplanning
Set up a plan for a good layout. Place the modules (modules can be
blocks, functional units, etc.) at an early stage when details like shape,
area, I/O pin positions of the modules, …, are not yet fixed.
Deadspace
28. Physical Design Cycle (4/6)
Placement – Exact placement of the modules (modules can be
gates, standard cells, etc.) when details of the module design are known.
The goal is to minimize the delay, total area and interconnect cost.
v
Feedthrough
Standard cell type 1
Standard cell type 2
29. Physical Design Cycle (5/6)
Routing – Complete the interconnections between modules. Factors
like critical path, clock skew, wire spacing, etc., are considered. Include
global routing and detailed routing.
v
Feedthrough
Type 1 standard cel1
Type 2 standard cell
30. Physical Design Cycle (6/6)
Compaction – Compress the layout from all directions to minimize the
total chip area.
Verification – Check the correctness of the layout. Include DRC (Design
Rule Checking), circuit extraction (generate a circuit from the layout to
compare with the original netlist), performance verification (extract
geometric information to compute resistance, capacitance, delay, etc.)
31. Design Style(1/3)
Physical design is an extremely complex process , even after breaking
the entire process into several easier steps.
Each step is computationally very hard .
Market requirements demand quick time-to-market and high yield.
As a result, restricted models and design styles are used to reduce the
complexity of physical design.
32. Design Styles (2/3)
Broadly DS can be classified as
Full-Custom ASICs
– Some (possibly all) logic cells are customized and all mask layers are
customized .
Semicustom ASICs
– All logic cells are predesigned (defined in cell library) and some (possibly
all) of the mask layers are customized
– Types:
Standard-cell based and Gate-array-based ASICs
33. Design Styles (3/3)
Programmable ASICs
– All logic cells are predesigned and none of the mask layers are customized
– Types: PLD (Programmable Logic Device) and
FPGA (Field Programmable Gate Array)
Selection of DS depends on factors like
1) type of chip
2) cost
3) time to market, etc.
34. Full-custom ASICs (1/3)
Engineers design some or all of the logic cells, circuits, or layout
specifically for one ASIC
– Full-custom ICs are the most expensive to manufacture and to design
– Manufacturing lead time (the time it takes just to make an IC – not
including design time) is typically 8 weeks
35. Full-custom ASICs (2/3)
When does it make sense?
– there are no suitable existing cell libraries available
– existing logic cells are not fast enough
– logic cells are not small enough
– logic cells consume too much power
Trends: fewer and fewer full-custom ICs are being designed (excluding mixed
analog/digital ASICs)
37. Standard-Cell-Based ASICs (1/3)
Cell-Based ASIC (CBIC) uses predesigned cells (AND, OR gates, multiplexers,
flip-flops, ...)
Standard-cell areas are built of rows of standard cells
Standard-cell areas can be used in combination with larger predesigned cells
(microcontrollers, or even microprocessors), known as megacells
A cell-based ASIC
(CBIC) die with a
single standard-cell
area combined with 4
fixed blocks
38. Standard-Cell-Based ASICs(2/2)
Characteristics
– custom blocks can be embedded;
ASIC designer defines only the placement of the standard cells and the
interconnect in a CBIC
– standard cells can be placed anywhere on a silicon =>
all mask layers of a CBIC are customized
– manufacturing lead time is 8 weeks
39. Standard-Cell-Based ASICs (3/3)
Advantages
– designers save time, money, and reduce risks using a predesigned,
pretested, and precharacterized standard-cell library
– standard cells in the library are constructed using full-custom;
each standard cell can be optimized individually
(for example, to maximize speed, minimize area, etc);
Disadvantages
– time or expense of designing or buying the standard-cell library
– time needed to fabricate all layers of the ASIC for each new design
40. Gate-Array-Based ASICs
In gate-array-based ASIC transistors are predefined on the
silicon wafer
– Base cell – the smallest element that is replicated to make
the base array.
– Base array – the predefined pattern of transistors on a
gate array.
Masked Gate Array (MGA): Only layers which define the
interconnect between transistors are defined by the designer
using custom masks.
41. Gate-Array-Based ASICs (1/4)
Since only metal interconnections are unique for MGA,we can use
prefabricated wafers (with completed transistor layers)
– the turnaround time is reduced to a few days or at most a couple of
weeks
– the costs for all the initial prefabrication steps for MGA are shared
for each consumer => the cost of an MGA is reduced compared to
FC and CBIC
Types: Channeled, Channelless, and Structured Gate Array
42. Gate-Array-Based ASICs (2/4)
Channeled gate array
– we leave space between the rows of transistors for wiring
Characteristics
– only interconnect is customized
– the interconnect uses predefined spaces between rows
– manufacturing lead time is between 2 days and 2 weeks
43. Gate-Array-Based ASICs (3/4)
Channelless gate array (sea-of-gates or SOG)
– there are no predefined areas set aside for routing between cells
– we customize the contact layer that defines the connections between
metal1 and transistors
Characteristics
– only some (the top few) mask layers
are customized – the interconnect
– manufacturing lead time is
between 2 days and 2 weeks
44. Gate-Array-Based ASICs (4/4)
Structured gate array or embedded gate array:
Combines features of CBIC and MGA motivation:
MGA has only fixed gate-array base cell;difficult and inefficient
implementation of memory we set aside some IC area and dedicate it to a
specific function(contain different cells, more suitable for building
memory cells, for example, or complete block, such as a microcontroller)
Characteristics:
- Only some (the top few) mask layers
are customized – the interconnect
- Custom blocks can be embedded
- Manufacturing lead time is
between 2 days and 2 weeks
Problem: embedded function is fixed
45. Programmable Logic Devices(1/2)
PLDs
– standard ICs, available in standard configurations
– sold in high volume to many different customers
– PLDs may be configured or programmed to create
a part customized to specific application
Characteristics
– no customized mask layers or logic cells
– fast design turnaround
– a single large block of programmable interconnect
– a matrix of logic macrocells that usually consists of programmable
array logic followed by a flip-flop or latch
46. Programmable Logic Devices(2/2)
Types of PLDs
PROM: Uses metal fuse that can be blown permanently
EPROM: Used programmable MOS transistors whose characteristics are altering by
applying a high voltage.
PAL : Programmable Array Logic programmable AND logic array or AND plane,
and fixed OR plane
PLA : Programmable Logic Array programmable AND plane
followed by programmable OR plane
Depending on how the PLD is programmed
erasable PLD (EPLD) mask-programmed PLD
47. Field-Programmable Gate Arrays
(FPGA)
FPGA
– a step above the PLD in complexity;
it is usually larger and more complex than a PLD
– rapidly growing in importance
Characteristics
– none of mask layers are customized
– a method for programming basic cells
and the interconnect
– the core is regular array
of programmable basic logic cells
(combinational + sequential)
– a matrix of programmable interconnect
that surrounds the basic cells
– programmable I/O cells around the core
– design turnaround is a few hours
48. Comparison
The choice of design style depends on the intended functionality of
the chip, time to market and total number of chips to be
manufactured.
Full custom DS is used for microprocessors and other complex
volume applications.
While FPGA may be used for simple and low volume applications.
Mixed style may be used.
For large circuits, it is common to partition the circuit into smaller
subcircuits which are designed using different team.
Each team may use different DS.
49. Comparison
Style
Full-custom Standard cell Gate Array FPGA
Cell size Var. Fixed height Fixed Fixed
Cell type Var. Var. Fixed Programmable
Cell placement Var. In row Fixed Fixed
Interconnections Var. Var. Var. Programmable
Design cost High Medium Medium low
50. Comparison
Style
Full-custom Standard cell Gate Array FPGA
Area Compact Compact to
moderate
Moderate Large
Performance High High to
moderate
Moderate Low
Fabrication All layers All layers Routing
layers only
No layers
51. Conclusion
Introducing VLSI Era
Types of VLSI design flow
Various Implementation Choices
VLSI Physical Design
