Event-Driven Architecture Masterclass: Integrating Distributed Data Stores Ac...
LISUN Flexing test-apparatus WQ-2
1. Brochure
Flexing Test Apparatus
(WQ-2)
Chapter 1 Summarize
(大标题,居中小三加粗,尽量在新一页,用 Chapter 区分)
1. Operating instruction (一级标题,左对齐小四加粗)
According to the requirements of CIE, IESNA and the National’s standard, this
system is a multi-measurement mode spectrophotometer system which can realize
B-β, A-α and C-γ etc through rotating lamps and lanterns.
It test Spatial, light intensity distribution curves on any cross section (can be shown
under the rectangular coordinate system or polar coordinate system), spatial
System configuration:
UV-263LS UV aging test Chamber
Global Office of Lisun Electronics Inc.
http://www.Lisungroup.com
Lisun Group (Hong Kong) Limited
Add: Room C, 15/F Hua Chiao Commercial Center, 678 Nathan Road, Mongkok,
Kowloon, Hong Kong
Tel: 00852-68852050 Fax: 00852-30785638
Email: SalesHK@Lisungroup.com
Lisun Electronics (Shanghai) Co., Ltd
Add: 113-114, No. 1 Building, Nanxiang Zhidi Industry Park, No. 1101, Huyi Road, Jiading
District, Shanghai, 201802, China
Tel: +86(21)5108 3341 Fax: +86(21)5108 3342
Email: SalesSH@Lisungroup.com
Lisun Electronics Inc. (USA)
Add: 445 S. Figueroa Street, Los Angeless, CA 90071, U.S.A.
Email: Sales@Lisungroup.com
Lisun China Factory
Add: NO. 37, Xiangyuan Road, Hangzhou City, Zhejiang Province, China
Tel: +86-189-1799-6096
Email: Engineering@Lisungroup.com
Lead in CFL & LED Test Instruments
Rev. 1/17/2019
2. Lisun Electronics Inc. Sales@Lisungroup.com www.Lisungroup.com
-Page 1 -
1. Test Objective
This machine is a special equipment for testing the bending fatigue strength of AC
and DC power cord. It can be automatic counting. When sample bending fold to
break causes no power, it can automatically stop operation. (standard type with
speed display)
2. Referring to standards
GB2099.1-2008< Household and Similar Use Plug Socket Part 1: General
Requirements> 23.4 soft cable and connecting requirements, as shown in figure 21
GB4706.1-2005<Household and Similar Use Household Appliance Part 1: General
Requirements>25.14 requirements, as shown in figure 8
GB/T5023.2-2008<Rated Voltage Equal to or Less Than 450/750 PVC Insulated
Cables Part 2: Test methods> Testing: Flexing Test, as shown in figure 2.Through
the conductor of electric current is about 0.1 A according to test requirement
Factory Inspection Site Representative Witness Test Guidelines Swing Testing(Cord
Sets and Power Supply Cord)
General requirements IEC60335-1
3. Technical Parameters
Fixture: 6 groups
Power supply: AC220V ±10% 5A
Motor power: 90W/220V AC
Angle Bending: Left or right 30、45、60、90 adjustable(0°-180°adjustable
continuously)(Weights can be changed according to customer’s needs)
3. Lisun Electronics Inc. Sales@Lisungroup.com www.Lisungroup.com
-Page 2 -
Bending Speed: Can be directly display, Header display
Counter: Six good parts counter, a preset counter
Weight: 50g,100g,113g,200g,284g,300g,500g(select)
Volume: 845×400×945MM
Failure judgment: When there is a broken line to be measured, the
corresponding LED lights are not bright, the corresponding good counter to stop
counting.
The show value is the times of bending about the tested power line. The
machine stops running when all lines to be measured are broken.
Qualified judgment: When the test line is set to achieve the number of tests, the
detection device automatically stops, and shows good count.