workover
•Download as DOCX, PDF•
1 like•580 views
1. The document provides calculations to determine well performance parameters like maximum production rate (Qmax), productivity index (PI), and pressure profiles from reservoir and well data. 2. An example calculation is shown to determine Qmax of 11,930 BFPD for well KB#059 using the Vogel equation and data provided. 3. The productivity index equation is derived from the original equation, showing that PI units are BPD/psi. 4. Another example calculates the Qmax of well KB#059 to be 17,834 BFPD using a different set of input data.
Report
Share
Report
Share
Recommended
Bit calculations
This document provides formulas for calculating various metrics related to diamond drill bits used in drilling operations. It includes formulas to calculate the pressure drop and nozzle velocity across the bit based on flow rate and mud weight. It also provides formulas to calculate the total nozzle area, impact force of jet nozzles on the hole bottom, cross flow velocity under the bit, and mechanical specific energy using coefficients of friction and drill bit torque measurements.
Fc025 w5 seminar_solutions_2
1. The document provides solutions to 13 fluid mechanics questions involving calculations of weight, pressure, force, flow rate, and other fluid properties.
2. Key concepts covered include relationships between pressure, density, height, volume, force, weight, and flow measurements.
3. Various conversion factors are provided and used in the calculations such as between psi and kPa or ft and m.
13 venting requirements
The document discusses the venting requirements for an oil storage tank according to API 2000 standards. It calculates the required venting capacities for outbreathing and inbreathing based on the tank size, filling rate, and other parameters. For outbreathing, the total required venting capacity is 81.95 Nm3/h. For inbreathing, the total required is 114.25 Nm3/h. It then verifies that the provided 300mm vent with an area of 706.86 cm2 is sufficient to meet both the outbreathing and inbreathing requirements.
สมการโคไค
This document provides numerous pharmacokinetic equations for modeling drug behavior in the body. It includes equations for calculating elimination rate constants, half-lives, plasma concentrations over time for single and multiple intravenous bolus doses, intravenous infusions, and oral administrations. It also includes equations related to volume of distribution, clearance, and using creatinine clearance to estimate kidney function.
Hvac formulas
The document contains formulas and information related to HVAC systems. It defines key terms like tons of refrigeration, horsepower, voltage, amperage, resistance, watts, capacitance, gas laws, and geometric formulas. It also includes formulas for calculating areas, volumes, BTUs, airflow, efficiency, and sizing components like ducts, grilles, burners, and nozzles.
Equations
This document contains equations and rules of thumb for HVAC systems. It includes equations for cooling and heating load calculations, ductwork sizing, fan and pump laws, expansion tank sizing, air balancing, efficiencies, cooling towers, moisture condensation, and electricity. The equations are presented along with brief explanations of the variables.
Offshore well intermediate
This document provides calculations for the capacities, volumes, and weights of components in an offshore well. It includes:
1) Calculations of internal string volumes, annular volumes, and wellbore volumes based on tubular dimensions.
2) Calculations of displacement volumes for individual components and the total string based on wall thicknesses, diameters, and lengths.
3) Calculations of component and total string weights in mud based on tubular dimensions, material density, and a buoyancy factor.
The document contains input data for tubular dimensions and properties, and outputs detailed volumetric and mass calculations for well design and drilling fluid management.
Bit calculations
This document provides equations to calculate various drilling parameters such as bit pressure drop, nozzle velocity, hydraulic horsepower, impact force, torque, and mechanical specific energy based on inputs like flow rate, mud weight, bit diameter, weight on bit, and rotation speed. The equations can be used to determine values for nozzle area and velocity from flow rate or pressure drop, as well as calculate impact force, cross flow velocity, specific energy, coefficient of friction, and minimum flow rate.
Recommended
Bit calculations
This document provides formulas for calculating various metrics related to diamond drill bits used in drilling operations. It includes formulas to calculate the pressure drop and nozzle velocity across the bit based on flow rate and mud weight. It also provides formulas to calculate the total nozzle area, impact force of jet nozzles on the hole bottom, cross flow velocity under the bit, and mechanical specific energy using coefficients of friction and drill bit torque measurements.
Fc025 w5 seminar_solutions_2
1. The document provides solutions to 13 fluid mechanics questions involving calculations of weight, pressure, force, flow rate, and other fluid properties.
2. Key concepts covered include relationships between pressure, density, height, volume, force, weight, and flow measurements.
3. Various conversion factors are provided and used in the calculations such as between psi and kPa or ft and m.
13 venting requirements
The document discusses the venting requirements for an oil storage tank according to API 2000 standards. It calculates the required venting capacities for outbreathing and inbreathing based on the tank size, filling rate, and other parameters. For outbreathing, the total required venting capacity is 81.95 Nm3/h. For inbreathing, the total required is 114.25 Nm3/h. It then verifies that the provided 300mm vent with an area of 706.86 cm2 is sufficient to meet both the outbreathing and inbreathing requirements.
สมการโคไค
This document provides numerous pharmacokinetic equations for modeling drug behavior in the body. It includes equations for calculating elimination rate constants, half-lives, plasma concentrations over time for single and multiple intravenous bolus doses, intravenous infusions, and oral administrations. It also includes equations related to volume of distribution, clearance, and using creatinine clearance to estimate kidney function.
Hvac formulas
The document contains formulas and information related to HVAC systems. It defines key terms like tons of refrigeration, horsepower, voltage, amperage, resistance, watts, capacitance, gas laws, and geometric formulas. It also includes formulas for calculating areas, volumes, BTUs, airflow, efficiency, and sizing components like ducts, grilles, burners, and nozzles.
Equations
This document contains equations and rules of thumb for HVAC systems. It includes equations for cooling and heating load calculations, ductwork sizing, fan and pump laws, expansion tank sizing, air balancing, efficiencies, cooling towers, moisture condensation, and electricity. The equations are presented along with brief explanations of the variables.
Offshore well intermediate
This document provides calculations for the capacities, volumes, and weights of components in an offshore well. It includes:
1) Calculations of internal string volumes, annular volumes, and wellbore volumes based on tubular dimensions.
2) Calculations of displacement volumes for individual components and the total string based on wall thicknesses, diameters, and lengths.
3) Calculations of component and total string weights in mud based on tubular dimensions, material density, and a buoyancy factor.
The document contains input data for tubular dimensions and properties, and outputs detailed volumetric and mass calculations for well design and drilling fluid management.
Bit calculations
This document provides equations to calculate various drilling parameters such as bit pressure drop, nozzle velocity, hydraulic horsepower, impact force, torque, and mechanical specific energy based on inputs like flow rate, mud weight, bit diameter, weight on bit, and rotation speed. The equations can be used to determine values for nozzle area and velocity from flow rate or pressure drop, as well as calculate impact force, cross flow velocity, specific energy, coefficient of friction, and minimum flow rate.
Smoke fan sizing
This document outlines calculations for a mechanical smoke ventilation system for a basement floor with a store. It determines the heat release rate and smoke mass flow rate based on the fire area and assumptions. It then calculates the required air flow rate, duct size, and fan specifications. The system will include two exhaust fans of 18,500 CFM each and two fresh air intake fans of 10,500 CFM each, all located on the roof. The ducts will be sized to accommodate the required air flow rates. The entrance areas are determined to provide sufficient fresh air intake.
Ejercicio de mecanica
This document presents the solution to a physics problem involving forces and torques. It provides known values for mass and gravitational acceleration. The solution involves setting up and solving two equations for the unknown torque (Dx) and normal force (Wc). This allows calculating the torque value, then substituting back into the first equation to find the applied force (P). The applied force is calculated to be 2237.3 Newtons.
In vitro canister life of cos absorber prepacks with different fresh gas flow...
In vitro canister life of cos absorber prepacks with different fresh gas flow...Meditech Equipment Co.,Ltd
This document presents the results of a study measuring the in vitro canister life of different CO2 absorber prepacks across a range of fresh gas flows. The study found that the fractional canister usage, or amount of each canister used per hour, increased linearly as the fresh gas flow increased for each brand. The canister life was longest for the SpiraLith brand, which is lithium-based and produces no compound A or CO. Of the calcium hydroxide-based brands, Amsorb and LoFloSorb, which do not contain sodium hydroxide, were less efficient but also do not produce compound A or CO.Setting of concrete
The document outlines the 8 steps for achieving a concrete mix design: 1) choosing slump, 2) choosing aggregate size, 3) estimating water and air content, 4) selecting water-cement ratio, 5) calculating cement content, 6) estimating aggregate content, 7) estimating fine aggregate content, and 8) conducting a laboratory trial batch. It then provides an example of designing a mix for a volume of 1.54 m3 using a ratio of 1:2:4 for cement, fine aggregate, and coarse aggregate respectively.
Wait and weight vs. driller
This document provides an example problem and solution for calculating pressures during well control using the driller's method and wait and weight method. It gives step-by-step calculations for determining pressures at various points when a gas kick occurs at the casing seat or at the surface. The example involves a well with a depth of 10,000 feet, and calculations are shown for determining pressures at 4,000 feet and at the surface when circulating kicks with the initial mud or a heavier kill mud.
BH6(2m)
The document reports the results of pressuremeter tests conducted at depths between 2 to 6.5 meters at three borehole locations. For each test, it provides the probe type used, initial volume, test depth, soil properties, pressure-volume data, and calculated pressuremeter parameters including Menard modulus, limit pressure, and elastic line slope.
Problem 3.1
The document provides calculations to determine the pressure of nitrogen in a tank and the minimum required wall thickness. It uses the ideal gas law to calculate the pressure as 3520 lbf/in2. It then sets up a force balance equation considering one hemisphere of the tank to determine the minimum wall thickness is 0.880 inches.
Kill sheet
This document discusses the key calculations involved in a kill sheet for plugging and abandoning an oil well. It explains that a kill sheet is used to determine well parameters like volume, strokes, time, mud weights, and circulating pressures. It provides step-by-step worked examples of calculating strokes, times, kill mud weight, initial and final circulating pressures, and a step down chart. The calculations allow operators to safely pump heavy kill mud into the well to displace the drilling fluid before cementing and abandoning the well.
Solutions manual for thermodynamics an interactive approach 1st edition by bh...
Solutions Manual for Thermodynamics An Interactive Approach 1st Edition by Bhattacharjee IBSN 9780133807974
Download at:
http://downloadlink.org/p/solutions-manual-for-thermodynamics-an-interactive-approach-1st-edition-by-bhattacharjee-ibsn-9780133807974/
thermodynamics an interactive approach bhattacharjee pdf
thermodynamics an interactive approach pdf
thermodynamics an interactive approach solutions manual pdf
thermodynamics bhattacharjee solutions
Solutions manual for fluid mechanics 1st edition by hibbeler ibsn 9780133770001
The document provides solutions to problems involving fluid mechanics. It includes solutions for problems about Pascal's law, pressure measurements at various depths, pressures in tanks and pipes, and determining pressures using fluid properties like density. For example, it calculates that the maximum pressure in a storage tank filled with oil reaching a level of 8 feet is 3.98 psi occurring at the base of the tank. It also finds that carbon tetrachloride will stop flowing from a tank when the pressure at the valve reaches the atmospheric pressure of 14.7 psi, which occurs at a height of 4.5 feet.
Selectionmec6 (1)
This document contains solutions to 6 fluid mechanics problems involving concepts like Bernoulli's equation, dynamic pressure, and flow rate calculations. Problem 6.70 asks the reader to express the mass flow rate through a nozzle in terms of the pressure difference ∆p between the inlet and exit, the inlet temperature T1, and the diameters D1 and D2 of the inlet and exit. The solution uses Bernoulli's equation between the inlet and exit, along with the relationship between flow velocity and pipe diameter, to derive an expression for the exit velocity V2 in terms of these parameters.
Kuzey soğutma kulesi̇ basinç kaybi
This document provides calculations to determine pressure losses between points in a piping system. It includes formulas for determining friction factor and Reynolds number. Pressure losses are calculated between each segment using the friction factor and flow properties. The total pressure loss calculated across the entire system is 1.414 bar. Key variables considered include pipe diameter, flow rate, fluid properties, and fittings. Friction factors are estimated based on pipe size from 0.0115 to 0.0135.
Troponin_T_monitoring_BIEN 167 MINI PROJECT 2
- Troponin T detection strips work by having blood flow through a paper strip with sensor and control bands. At least 0.18 ug/L of troponin T is needed in the blood sample for a positive reading.
- COMSOL was used to simulate the diffusion and flow of troponin T through the paper strip at different pressures.
- Calculations were done to determine the minimum pressure needed to drive flow through the strip based on parameters like strip dimensions, diffusion rate, and viscosity.
A non-Iterative way for preliminary designing Plate & Frame Exchanger
This document summarizes the calculation of heat transfer coefficients and overall heat transfer coefficient for a heat exchanger using the Timmerhaus method. It provides properties for methanol and water streams, calculates individual heat transfer coefficients accounting for fouling, and determines the number of transfer units (NTU), overall heat transfer coefficient, flow velocities and heat transfer rates.
Theoretical Hazardous Site Remediation Project
This memo style report analyzes an approach to the reduction of ground toxins in an urban environment using counter-current immiscible extraction technology. It emphasizes the applications of chemical engineering separations in real world situations. This report was created as part of a course observing advanced chemical separation processes at Worcester Polytechnic Institute.
Fluid ans t_2
This document contains 11 multi-step physics problems involving fluid mechanics concepts like pressure, viscosity, density, and fluid flow. The problems are solved with relevant equations for ideal gases, compressible fluids, laminar flow, and viscometry. Key values are calculated, such as mass, pressure, shear stress, drag force, velocity, and viscosity.
Group8 presentation
1) The document presents the process and mechanical design of a packed bed extractor to extract 96% of benzene from a feed mixture of 78% 1-hexene and 22% benzene using tetra-methylene sulphone as the solvent.
2) Key steps in the process design include determining the equilibrium curve, mass flow rates, minimum solvent rate, dispersed and continuous phase properties, flooding velocity, column diameter, mass transfer coefficient, number of transfer units, and column height.
3) Key steps in the mechanical design include determining the shell and head thickness, stresses from various loads, internal packing support, and distributor specifications. Lessing rings are identified as the optimum packing material.
final press-rev-Linkedin
This document summarizes the results of a simulation analyzing pool boiling over microstructures. The simulation used a volume of fluid (VOF) model to model bubble growth and departure. Key findings include:
1) The simulation matched experimental data on bubble shape and diameter with a maximum error of 9%. It predicted a departure diameter of 4.6 mm at 43 ms, consistent with the experimental period of 52 ms between departures.
2) Shear stress analysis found higher stress during necking and departure, identifying the influence region on the heated wall close to 2 times the departure diameter.
3) Heat transfer coefficients increased near the departing bubble, demonstrating microconvection effects during bubble growth and departure.
Dryers
A rotary dryer is used to dry sand with the following specifications:
- Wet sand at 30°C with 7% moisture is dried to 0.5% moisture at 115°C.
- 20 metric tons of dried sand is produced per hour.
- Bunker oil at 41870 kJ/kg HHV is used as fuel with an efficiency of 60%.
Calculating the heat requirements and fuel consumption rate, 204 kg/hr of bunker oil is needed, equivalent to 227 liters/hr.
Chapter2
1) The document discusses water passing through a pressure-reducing valve and separating tank, including its state and amount that leaves as vapor.
2) It also discusses heat transfer calculations for air heated in an exchanger and flow rate measurement using a venturi meter.
3) Heat transfer principles and equations are reviewed for various processes, including perfect gas behavior, convection coefficients, radiation from a human body, and insensible evaporation heat loss.
01 why do_we_need_artificial_lift
This document discusses artificial lift and well performance. It begins by explaining that as reservoir pressure declines, artificial lift is needed to produce fluids from the well. It then provides background on Darcy's law, which describes the relationship between flow rate and pressure differences for fluid flow through porous media. The document discusses how Darcy's law is applied to model radial flow into a wellbore, and how the productivity index (PI) is calculated. It also covers factors that affect well performance, such as water cut, gas interference, skin damage, pressure depletion over time, and tubing size.
VLP AND WORKING CHART LECTURE #2.pdf
This document discusses vertical lift relationships and working charts used to determine production parameters like PWF given other known values. It provides an example of using a working chart for a 1.5" tubing to calculate a PWF of 1600 psi given a PTH of 200 psi, flow rate of 500 bbl/day, well depth of 5000 ft, and GLR of 200 scf/bbl. It also demonstrates using vertical flow performance curves and an IPR curve to determine an allowable flow rate of 820 bbl/day at a PWF of 1450 psi.
More Related Content
What's hot
Smoke fan sizing
This document outlines calculations for a mechanical smoke ventilation system for a basement floor with a store. It determines the heat release rate and smoke mass flow rate based on the fire area and assumptions. It then calculates the required air flow rate, duct size, and fan specifications. The system will include two exhaust fans of 18,500 CFM each and two fresh air intake fans of 10,500 CFM each, all located on the roof. The ducts will be sized to accommodate the required air flow rates. The entrance areas are determined to provide sufficient fresh air intake.
Ejercicio de mecanica
This document presents the solution to a physics problem involving forces and torques. It provides known values for mass and gravitational acceleration. The solution involves setting up and solving two equations for the unknown torque (Dx) and normal force (Wc). This allows calculating the torque value, then substituting back into the first equation to find the applied force (P). The applied force is calculated to be 2237.3 Newtons.
In vitro canister life of cos absorber prepacks with different fresh gas flow...
In vitro canister life of cos absorber prepacks with different fresh gas flow...Meditech Equipment Co.,Ltd
This document presents the results of a study measuring the in vitro canister life of different CO2 absorber prepacks across a range of fresh gas flows. The study found that the fractional canister usage, or amount of each canister used per hour, increased linearly as the fresh gas flow increased for each brand. The canister life was longest for the SpiraLith brand, which is lithium-based and produces no compound A or CO. Of the calcium hydroxide-based brands, Amsorb and LoFloSorb, which do not contain sodium hydroxide, were less efficient but also do not produce compound A or CO.Setting of concrete
The document outlines the 8 steps for achieving a concrete mix design: 1) choosing slump, 2) choosing aggregate size, 3) estimating water and air content, 4) selecting water-cement ratio, 5) calculating cement content, 6) estimating aggregate content, 7) estimating fine aggregate content, and 8) conducting a laboratory trial batch. It then provides an example of designing a mix for a volume of 1.54 m3 using a ratio of 1:2:4 for cement, fine aggregate, and coarse aggregate respectively.
Wait and weight vs. driller
This document provides an example problem and solution for calculating pressures during well control using the driller's method and wait and weight method. It gives step-by-step calculations for determining pressures at various points when a gas kick occurs at the casing seat or at the surface. The example involves a well with a depth of 10,000 feet, and calculations are shown for determining pressures at 4,000 feet and at the surface when circulating kicks with the initial mud or a heavier kill mud.
BH6(2m)
The document reports the results of pressuremeter tests conducted at depths between 2 to 6.5 meters at three borehole locations. For each test, it provides the probe type used, initial volume, test depth, soil properties, pressure-volume data, and calculated pressuremeter parameters including Menard modulus, limit pressure, and elastic line slope.
Problem 3.1
The document provides calculations to determine the pressure of nitrogen in a tank and the minimum required wall thickness. It uses the ideal gas law to calculate the pressure as 3520 lbf/in2. It then sets up a force balance equation considering one hemisphere of the tank to determine the minimum wall thickness is 0.880 inches.
Kill sheet
This document discusses the key calculations involved in a kill sheet for plugging and abandoning an oil well. It explains that a kill sheet is used to determine well parameters like volume, strokes, time, mud weights, and circulating pressures. It provides step-by-step worked examples of calculating strokes, times, kill mud weight, initial and final circulating pressures, and a step down chart. The calculations allow operators to safely pump heavy kill mud into the well to displace the drilling fluid before cementing and abandoning the well.
Solutions manual for thermodynamics an interactive approach 1st edition by bh...
Solutions Manual for Thermodynamics An Interactive Approach 1st Edition by Bhattacharjee IBSN 9780133807974
Download at:
http://downloadlink.org/p/solutions-manual-for-thermodynamics-an-interactive-approach-1st-edition-by-bhattacharjee-ibsn-9780133807974/
thermodynamics an interactive approach bhattacharjee pdf
thermodynamics an interactive approach pdf
thermodynamics an interactive approach solutions manual pdf
thermodynamics bhattacharjee solutions
Solutions manual for fluid mechanics 1st edition by hibbeler ibsn 9780133770001
The document provides solutions to problems involving fluid mechanics. It includes solutions for problems about Pascal's law, pressure measurements at various depths, pressures in tanks and pipes, and determining pressures using fluid properties like density. For example, it calculates that the maximum pressure in a storage tank filled with oil reaching a level of 8 feet is 3.98 psi occurring at the base of the tank. It also finds that carbon tetrachloride will stop flowing from a tank when the pressure at the valve reaches the atmospheric pressure of 14.7 psi, which occurs at a height of 4.5 feet.
Selectionmec6 (1)
This document contains solutions to 6 fluid mechanics problems involving concepts like Bernoulli's equation, dynamic pressure, and flow rate calculations. Problem 6.70 asks the reader to express the mass flow rate through a nozzle in terms of the pressure difference ∆p between the inlet and exit, the inlet temperature T1, and the diameters D1 and D2 of the inlet and exit. The solution uses Bernoulli's equation between the inlet and exit, along with the relationship between flow velocity and pipe diameter, to derive an expression for the exit velocity V2 in terms of these parameters.
Kuzey soğutma kulesi̇ basinç kaybi
This document provides calculations to determine pressure losses between points in a piping system. It includes formulas for determining friction factor and Reynolds number. Pressure losses are calculated between each segment using the friction factor and flow properties. The total pressure loss calculated across the entire system is 1.414 bar. Key variables considered include pipe diameter, flow rate, fluid properties, and fittings. Friction factors are estimated based on pipe size from 0.0115 to 0.0135.
Troponin_T_monitoring_BIEN 167 MINI PROJECT 2
- Troponin T detection strips work by having blood flow through a paper strip with sensor and control bands. At least 0.18 ug/L of troponin T is needed in the blood sample for a positive reading.
- COMSOL was used to simulate the diffusion and flow of troponin T through the paper strip at different pressures.
- Calculations were done to determine the minimum pressure needed to drive flow through the strip based on parameters like strip dimensions, diffusion rate, and viscosity.
A non-Iterative way for preliminary designing Plate & Frame Exchanger
This document summarizes the calculation of heat transfer coefficients and overall heat transfer coefficient for a heat exchanger using the Timmerhaus method. It provides properties for methanol and water streams, calculates individual heat transfer coefficients accounting for fouling, and determines the number of transfer units (NTU), overall heat transfer coefficient, flow velocities and heat transfer rates.
Theoretical Hazardous Site Remediation Project
This memo style report analyzes an approach to the reduction of ground toxins in an urban environment using counter-current immiscible extraction technology. It emphasizes the applications of chemical engineering separations in real world situations. This report was created as part of a course observing advanced chemical separation processes at Worcester Polytechnic Institute.
Fluid ans t_2
This document contains 11 multi-step physics problems involving fluid mechanics concepts like pressure, viscosity, density, and fluid flow. The problems are solved with relevant equations for ideal gases, compressible fluids, laminar flow, and viscometry. Key values are calculated, such as mass, pressure, shear stress, drag force, velocity, and viscosity.
Group8 presentation
1) The document presents the process and mechanical design of a packed bed extractor to extract 96% of benzene from a feed mixture of 78% 1-hexene and 22% benzene using tetra-methylene sulphone as the solvent.
2) Key steps in the process design include determining the equilibrium curve, mass flow rates, minimum solvent rate, dispersed and continuous phase properties, flooding velocity, column diameter, mass transfer coefficient, number of transfer units, and column height.
3) Key steps in the mechanical design include determining the shell and head thickness, stresses from various loads, internal packing support, and distributor specifications. Lessing rings are identified as the optimum packing material.
final press-rev-Linkedin
This document summarizes the results of a simulation analyzing pool boiling over microstructures. The simulation used a volume of fluid (VOF) model to model bubble growth and departure. Key findings include:
1) The simulation matched experimental data on bubble shape and diameter with a maximum error of 9%. It predicted a departure diameter of 4.6 mm at 43 ms, consistent with the experimental period of 52 ms between departures.
2) Shear stress analysis found higher stress during necking and departure, identifying the influence region on the heated wall close to 2 times the departure diameter.
3) Heat transfer coefficients increased near the departing bubble, demonstrating microconvection effects during bubble growth and departure.
Dryers
A rotary dryer is used to dry sand with the following specifications:
- Wet sand at 30°C with 7% moisture is dried to 0.5% moisture at 115°C.
- 20 metric tons of dried sand is produced per hour.
- Bunker oil at 41870 kJ/kg HHV is used as fuel with an efficiency of 60%.
Calculating the heat requirements and fuel consumption rate, 204 kg/hr of bunker oil is needed, equivalent to 227 liters/hr.
Chapter2
1) The document discusses water passing through a pressure-reducing valve and separating tank, including its state and amount that leaves as vapor.
2) It also discusses heat transfer calculations for air heated in an exchanger and flow rate measurement using a venturi meter.
3) Heat transfer principles and equations are reviewed for various processes, including perfect gas behavior, convection coefficients, radiation from a human body, and insensible evaporation heat loss.
What's hot (20)
In vitro canister life of cos absorber prepacks with different fresh gas flow...
In vitro canister life of cos absorber prepacks with different fresh gas flow...
Solutions manual for thermodynamics an interactive approach 1st edition by bh...
Solutions manual for thermodynamics an interactive approach 1st edition by bh...
Solutions manual for fluid mechanics 1st edition by hibbeler ibsn 9780133770001
Solutions manual for fluid mechanics 1st edition by hibbeler ibsn 9780133770001
A non-Iterative way for preliminary designing Plate & Frame Exchanger
A non-Iterative way for preliminary designing Plate & Frame Exchanger
Similar to workover
01 why do_we_need_artificial_lift
This document discusses artificial lift and well performance. It begins by explaining that as reservoir pressure declines, artificial lift is needed to produce fluids from the well. It then provides background on Darcy's law, which describes the relationship between flow rate and pressure differences for fluid flow through porous media. The document discusses how Darcy's law is applied to model radial flow into a wellbore, and how the productivity index (PI) is calculated. It also covers factors that affect well performance, such as water cut, gas interference, skin damage, pressure depletion over time, and tubing size.
VLP AND WORKING CHART LECTURE #2.pdf
This document discusses vertical lift relationships and working charts used to determine production parameters like PWF given other known values. It provides an example of using a working chart for a 1.5" tubing to calculate a PWF of 1600 psi given a PTH of 200 psi, flow rate of 500 bbl/day, well depth of 5000 ft, and GLR of 200 scf/bbl. It also demonstrates using vertical flow performance curves and an IPR curve to determine an allowable flow rate of 820 bbl/day at a PWF of 1450 psi.
4_5861695641012407552 (1).pdf
This document contains solutions to practice well control questions from an IWCF student exercise book. It covers topics like calculating mud weight to balance formation pressure, circulating pressure calculations, well control principles like maintaining bottom hole pressure, and recognizing and responding to well kicks. Several questions involve calculating pressures using formation pressure gradients, mud weights, and well geometry. The document demonstrates how to apply well control equations to analyze drilling operations and well control situations.
1590701599PTE_526-Natural_Gas_Engineering (1).pptx
This course is all about Natural gas engineering from the Federal University of Technology owerri, it has concise explanations about the different topics in it
Sugar mill evaporator and Batch pan designing and control
The document discusses the design of multiple effect evaporators and sugar boiling pans. It provides information on:
1. The objectives and functions of multiple effect evaporators, which use multiple effects to concentrate juice with minimum energy usage.
2. Design considerations for different components of evaporators like tubes, tube plates, down takes, and catchalls.
3. Calculations for determining dimensions of these components based on factors like heating surface, circulation ratio, and vapour flow rates.
4. Similar design aspects and parameters for sugar boiling pans used for final boiling, including tube specifications, graining volume, and hydrostatic head.
Pelton turbine (1)
This document describes the design process for a Pelton turbine. It begins with the key dimensions and equations for Pelton turbines. It then provides an example of dimensioning a Pelton turbine with the given parameters of flow rate, head, and power output. The process involves choosing values for variables like number of nozzles and buckets, then calculating dimensions like jet diameter, runner diameter, and speed based on the design equations.
Numerical Simulation of a 3-D Reservoir
Three (3) dimensional one-phase fluid (oil) reservoir simulator using a partially implicit method with lagging coefficients. Skin damage after drilling the production well was expected; the impact of the skin damage and the necessity of well stimulation was assessed
Numerical Simulation of a 3-D Subsurface Reservoir
Three (3) dimensional one-phase fluid (oil) reservoir simulator using a partially implicit method with lagging coefficients. Skin damage after drilling the production well was expected; the impact of the skin damage and the necessity of well stimulation was assessed
Hvac formulas
The document provides formulas and definitions for various HVAC concepts. Some key formulas include: the ton of refrigeration which is equal to 288,000 BTU/24 hr or 12,000 BTU/hr; one horsepower equals 33,000 ft-lb of work in one minute or 746 Watts; converting between BTUs, KWs and Watts for heating and cooling equipment. Common gas laws and formulas for area, perimeter, volume and capacitance are also listed.
TPM.pptx
This document describes developing a program to calculate absolute permeability (k) from input parameters more quickly than existing methods. The program uses an equation relating k, mean pressure (pm), and air permeability (kg) to iteratively calculate k. Users input kg, initial k guess (ki), pm, and error tolerance. Clicking "Calculate" runs the calculation and displays the final k and iteration count. The program was created with a graphical user interface for usability.
Precast driven pile 450 x450
This document provides the design and analysis of precast driven piles for a proposed 2x660MW thermal power project in Rampal, Bangladesh. It evaluates the pile for stresses during driving and lifting/pitching, and checks the axial, uplift, lateral and flexural capacities of the pile section. The analysis considers a 450mm x 450mm square precast pile with 26m length. It determines the pile can safely resist all assessed stresses and loads with the proposed reinforcement details.
Numerical Simulation of 2-D Subsurface Reservoir
This document provides a detailed summary of a reservoir simulation project, including:
- The properties of the rectangular oil reservoir being modeled, including dimensions, porosity, permeability, and fluid properties.
- The discretization of the reservoir into 165 grid blocks for simulation.
- The partial differential equations and initial/boundary conditions used in the reservoir simulation.
- How well production is incorporated and calculated using Peaceman's method.
- Details on running a "leakproof test" to validate that pressures and saturations remain constant with no well flow.
Pile Foundationsvjhvjvgyujgvuyjgiugiug.pptx
1) Meyerhof's method estimates skin friction (QS) by calculating the unit friction (f) between the pile and soil, which increases linearly with depth up to a critical depth (L') and then remains constant. L' is typically 15 times the pile diameter (D).
2) Coyle and Castello's method estimates QS using field test data, with QS equal to the lateral earth pressure coefficient (K) times the average effective overburden pressure times the soil-pile friction angle times the pile perimeter length.
3) In sand, QS can be correlated to standard penetration test (SPT) N-values, with higher N-values giving higher skin friction. QS is calculated by multiplying the
Rectangular tank example_latest
The document provides design details for a rectangular concrete tank with three chambers. It discusses load combinations and factors used by the Portland Cement Association (PCA) that differ slightly from American Concrete Institute (ACI) specifications. An interior wall and short exterior wall of the tank are then designed. The interior wall is designed for both vertical and horizontal bending using #8 bars spaced at 6 inches and 8 inches, respectively. The short exterior wall uses a 14 inch thickness with #6 bars at 8 inches for vertical bending to resist a moment of 28,672 lb-ft/ft.
Solution Manual for Physical Chemistry – Robert Alberty
https://www.book4me.xyz/solution-manual-physical-chemistry-alberty/
Solution Manual for Physical Chemistry - 6th Edition
Author(s) : Robert A. Alberty
This solution manual include all chapters of textbook (1 to 21).
Welhead and Flowlines.pdf111111111111111
This document discusses wellhead and surface gathering systems. It covers flow through chokes, which experience pressure drops, and provides equations to calculate single-phase liquid and gas-liquid flow rates through chokes. It also discusses flow through flowlines and provides pressure gradient correlations for calculating flow through pipelines. Finally, it mentions gathering systems and gathering manifolds.
90 mm pipe 45 deg
1. This document analyzes the thrust block parameters for a 90mm diameter pipe bent at 45 degrees. It calculates thrust values, soil and concrete weights, buoyancy forces, and passive soil resistance.
2. Stability is evaluated for overturning, sliding, and buoyancy at the design pressure of 450 kN/m2 and hydrostatic test pressure of 675 kN/m2. Factors of safety are above 1.5, indicating the thrust block design is safe.
3. The key parameters of the 90mm diameter pipe bent at 45 degrees are summarized, including the design and hydrostatic test pressures used in the stability evaluations.
Numerical Simulation Study of a 1-D Subsurface Reservoir
The document describes a reservoir simulation study involving the discretization of a rectangular oil reservoir into 21 simulation cells. Equations describing fluid flow are presented for cells with and without wells. A system of implicit equations is developed by applying the block-centered grid discretization technique to each cell. The equations account for the presence of 5 wells - 2 production wells and 3 injection wells. Boundary and initial conditions are also specified. Discretized equations are written out for each cell to set up the system of equations to be solved.
6._Bearing_Capacity_from_other_methods.pdf
This document discusses methods for estimating bearing capacity based on in-situ and laboratory tests. The most common in-situ tests are the Standard Penetration Test (SPT) and Cone Penetration Test (CPT). The SPT involves dropping a weight to penetrate a split spoon sampler and counting the number of blows, which is used to estimate bearing capacity based on empirical correlations. The CPT provides a continuous profile by measuring cone resistance, which can also be empirically correlated to bearing capacity. The document also discusses estimating bearing capacity from vane shear tests and plate load tests.
Engineering formula sheet
This document contains formulas and definitions for engineering concepts related to probability, statistics, geometry, trigonometry, mechanics, electricity, thermodynamics, materials properties, and structural analysis. Some key formulas included are for binomial probability, mean, standard deviation, circle area and circumference, trigonometric ratios, force, work, power, heat transfer, stress, strain, modulus of elasticity, centroid location, and beam reactions and deflections. SI prefixes and unit conversions are also provided.
Similar to workover (20)
1590701599PTE_526-Natural_Gas_Engineering (1).pptx
1590701599PTE_526-Natural_Gas_Engineering (1).pptx
Sugar mill evaporator and Batch pan designing and control
Sugar mill evaporator and Batch pan designing and control
Numerical Simulation of a 3-D Subsurface Reservoir
Numerical Simulation of a 3-D Subsurface Reservoir
Solution Manual for Physical Chemistry – Robert Alberty
Solution Manual for Physical Chemistry – Robert Alberty
Numerical Simulation Study of a 1-D Subsurface Reservoir
Numerical Simulation Study of a 1-D Subsurface Reservoir
Recently uploaded
原版一比一多伦多大学毕业证(UofT毕业证书)如何办理
原版制作【微信:41543339】【多伦多大学毕业证(UofT毕业证书)】【微信:41543339】《成绩单、外壳、雅思、offer、真实留信官方学历认证（永久存档/真实可查）》采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【我们承诺采用的是学校原版纸张（纸质、底色、纹路）我们拥有全套进口原装设备，特殊工艺都是采用不同机器制作，仿真度基本可以达到100%，所有工艺效果都可提前给客户展示，不满意可以根据客户要求进行调整，直到满意为止！】
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信41543339】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信41543339】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
留信网服务项目：
1、留学生专业人才库服务（留信分析）
2、国（境）学习人员提供就业推荐信服务
3、留学人员区块链存储服务
【关于价格问题（保证一手价格）】
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：客户在留信官方认证查询网站查询到认证通过结果后付款，不成功不收费！
一比一原版(Unimelb毕业证书)墨尔本大学毕业证如何办理
原版制作【微信:41543339】【(Unimelb毕业证书)墨尔本大学毕业证】【微信:41543339】《成绩单、外壳、雅思、offer、留信学历认证（永久存档/真实可查）》采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【我们承诺采用的是学校原版纸张（纸质、底色、纹路），我们拥有全套进口原装设备，特殊工艺都是采用不同进口机器一比一制作，仿真度基本可以达到100%，所有工艺效果都可提前给客户展示，不满意可以根据客户要求进行调整，直到满意为止！】
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信41543339】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信41543339】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
留信网服务项目：
1、留学生专业人才库服务（留信分析）
2、国（境）学习人员提供就业推荐信服务
3、留学人员区块链存储服务
【关于价格问题（保证一手价格）】
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：客户在留信官方认证查询网站查询到认证通过结果后付款，不成功不收费！
End-to-end pipeline agility - Berlin Buzzwords 2024
We describe how we achieve high change agility in data engineering by eliminating the fear of breaking downstream data pipelines through end-to-end pipeline testing, and by using schema metaprogramming to safely eliminate boilerplate involved in changes that affect whole pipelines.
A quick poll on agility in changing pipelines from end to end indicated a huge span in capabilities. For the question "How long time does it take for all downstream pipelines to be adapted to an upstream change," the median response was 6 months, but some respondents could do it in less than a day. When quantitative data engineering differences between the best and worst are measured, the span is often 100x-1000x, sometimes even more.
A long time ago, we suffered at Spotify from fear of changing pipelines due to not knowing what the impact might be downstream. We made plans for a technical solution to test pipelines end-to-end to mitigate that fear, but the effort failed for cultural reasons. We eventually solved this challenge, but in a different context. In this presentation we will describe how we test full pipelines effectively by manipulating workflow orchestration, which enables us to make changes in pipelines without fear of breaking downstream.
Making schema changes that affect many jobs also involves a lot of toil and boilerplate. Using schema-on-read mitigates some of it, but has drawbacks since it makes it more difficult to detect errors early. We will describe how we have rejected this tradeoff by applying schema metaprogramming, eliminating boilerplate but keeping the protection of static typing, thereby further improving agility to quickly modify data pipelines without fear.
The Ipsos - AI - Monitor 2024 Report.pdf
According to Ipsos AI Monitor's 2024 report, 65% Indians said that products and services using AI have profoundly changed their daily life in the past 3-5 years.
一比一原版(UCSF文凭证书)旧金山分校毕业证如何办理
毕业原版【微信:176555708】【(UCSF毕业证书)旧金山分校毕业证】【微信:176555708】成绩单、外壳、offer、留信学历认证（永久存档真实可查）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【我们承诺采用的是学校原版纸张（纸质、底色、纹路），我们拥有全套进口原装设备，特殊工艺都是采用不同机器制作，仿真度基本可以达到100%，所有工艺效果都可提前给客户展示，不满意可以根据客户要求进行调整，直到满意为止！】
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信176555708】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信176555708】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
留信网服务项目：
1、留学生专业人才库服务（留信分析）
2、国（境）学习人员提供就业推荐信服务
3、留学人员区块链存储服务
→ 【关于价格问题（保证一手价格）】
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：客户在留信官方认证查询网站查询到认证通过结果后付款，不成功不收费！
Intelligence supported media monitoring in veterinary medicine
Media monitoring in veterinary medicien
一比一原版兰加拉学院毕业证(Langara毕业证书)学历如何办理
原版办【微信号:BYZS866】【兰加拉学院毕业证(Langara毕业证书)】【微信号:BYZS866】《成绩单、外壳、雅思、offer、真实留信官方学历认证（永久存档/真实可查）》采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【我们承诺采用的是学校原版纸张（纸质、底色、纹路）我们拥有全套进口原装设备，特殊工艺都是采用不同机器制作，仿真度基本可以达到100%，所有工艺效果都可提前给客户展示，不满意可以根据客户要求进行调整，直到满意为止！】
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信号BYZS866】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信号BYZS866】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
留信网服务项目：
1、留学生专业人才库服务（留信分析）
2、国（境）学习人员提供就业推荐信服务
3、留学人员区块链存储服务
【关于价格问题（保证一手价格）】
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：客户在留信官方认证查询网站查询到认证通过结果后付款，不成功不收费！
Build applications with generative AI on Google Cloud
We will explore Vertex AI - Model Garden powered experiences, we are going to learn more about the integration of these generative AI APIs. We are going to see in action what the Gemini family of generative models are for developers to build and deploy AI-driven applications. Vertex AI includes a suite of foundation models, these are referred to as the PaLM and Gemini family of generative ai models, and they come in different versions. We are going to cover how to use via API to: - execute prompts in text and chat - cover multimodal use cases with image prompts. - finetune and distill to improve knowledge domains - run function calls with foundation models to optimize them for specific tasks. At the end of the session, developers will understand how to innovate with generative AI and develop apps using the generative ai industry trends.
Beyond the Basics of A/B Tests: Highly Innovative Experimentation Tactics You...
This webinar will explore cutting-edge, less familiar but powerful experimentation methodologies which address well-known limitations of standard A/B Testing. Designed for data and product leaders, this session aims to inspire the embrace of innovative approaches and provide insights into the frontiers of experimentation!
Orchestrating the Future: Navigating Today's Data Workflow Challenges with Ai...
Navigating today's data landscape isn't just about managing workflows; it's about strategically propelling your business forward. Apache Airflow has stood out as the benchmark in this arena, driving data orchestration forward since its early days. As we dive into the complexities of our current data-rich environment, where the sheer volume of information and its timely, accurate processing are crucial for AI and ML applications, the role of Airflow has never been more critical.
In my journey as the Senior Engineering Director and a pivotal member of Apache Airflow's Project Management Committee (PMC), I've witnessed Airflow transform data handling, making agility and insight the norm in an ever-evolving digital space. At Astronomer, our collaboration with leading AI & ML teams worldwide has not only tested but also proven Airflow's mettle in delivering data reliably and efficiently—data that now powers not just insights but core business functions.
This session is a deep dive into the essence of Airflow's success. We'll trace its evolution from a budding project to the backbone of data orchestration it is today, constantly adapting to meet the next wave of data challenges, including those brought on by Generative AI. It's this forward-thinking adaptability that keeps Airflow at the forefront of innovation, ready for whatever comes next.
The ever-growing demands of AI and ML applications have ushered in an era where sophisticated data management isn't a luxury—it's a necessity. Airflow's innate flexibility and scalability are what makes it indispensable in managing the intricate workflows of today, especially those involving Large Language Models (LLMs).
This talk isn't just a rundown of Airflow's features; it's about harnessing these capabilities to turn your data workflows into a strategic asset. Together, we'll explore how Airflow remains at the cutting edge of data orchestration, ensuring your organization is not just keeping pace but setting the pace in a data-driven future.
Session in https://budapestdata.hu/2024/04/kaxil-naik-astronomer-io/ | https://dataml24.sessionize.com/session/667627
DSSML24_tspann_CodelessGenerativeAIPipelines
Codeless Generative AI Pipelines
(GenAI with Milvus)
https://ml.dssconf.pl/user.html#!/lecture/DSSML24-041a/rate
Discover the potential of real-time streaming in the context of GenAI as we delve into the intricacies of Apache NiFi and its capabilities. Learn how this tool can significantly simplify the data engineering workflow for GenAI applications, allowing you to focus on the creative aspects rather than the technical complexities. I will guide you through practical examples and use cases, showing the impact of automation on prompt building. From data ingestion to transformation and delivery, witness how Apache NiFi streamlines the entire pipeline, ensuring a smooth and hassle-free experience.
Timothy Spann
https://www.youtube.com/@FLaNK-Stack
https://medium.com/@tspann
https://www.datainmotion.dev/
milvus, unstructured data, vector database, zilliz, cloud, vectors, python, deep learning, generative ai, genai, nifi, kafka, flink, streaming, iot, edge
Population Growth in Bataan: The effects of population growth around rural pl...
A population analysis specific to Bataan.
办(uts毕业证书)悉尼科技大学毕业证学历证书原版一模一样
原版一模一样【微信：741003700 】【(uts毕业证书)悉尼科技大学毕业证学历证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
UofT毕业证如何办理
原件一模一样【微信：95270640】【多伦多大学毕业证UofT学位证成绩单】【微信：95270640】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：95270640】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：95270640】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份【微信：95270640】
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
办理多伦多大学毕业证硕士毕业证成绩单UofT学位证【微信：95270640 】外观非常精致，由特殊纸质材料制成，上面印有校徽、校名、毕业生姓名、专业等信息。
办理多伦多大学毕业证UofT学位证硕士毕业证成绩单【微信：95270640 】格式相对统一，各专业都有相应的模板。通常包括以下部分：
校徽：象征着学校的荣誉和传承。
校名:学校英文全称
授予学位：本部分将注明获得的具体学位名称。
毕业生姓名：这是最重要的信息之一，标志着该证书是由特定人员获得的。
颁发日期：这是毕业正式生效的时间，也代表着毕业生学业的结束。
其他信息：根据不同的专业和学位，可能会有一些特定的信息或章节。
办理多伦多大学毕业证硕士毕业证成绩单UofT学位证【微信：95270640 】价值很高，需要妥善保管。一般来说，应放置在安全、干燥、防潮的地方，避免长时间暴露在阳光下。如需使用，最好使用复印件而不是原件，以免丢失。
综上所述，办理多伦多大学毕业证硕士毕业证成绩单UofT学位证【微信：95270640 】是证明身份和学历的高价值文件。外观简单庄重，格式统一，包括重要的个人信息和发布日期。对持有人来说，妥善保管是非常重要的。
STATATHON: Unleashing the Power of Statistics in a 48-Hour Knowledge Extravag...
"Join us for STATATHON, a dynamic 2-day event dedicated to exploring statistical knowledge and its real-world applications. From theory to practice, participants engage in intensive learning sessions, workshops, and challenges, fostering a deeper understanding of statistical methodologies and their significance in various fields."
Recently uploaded (20)
Monthly Management report for the Month of May 2024
Monthly Management report for the Month of May 2024
Challenges of Nation Building-1.pptx with more important
Challenges of Nation Building-1.pptx with more important
End-to-end pipeline agility - Berlin Buzzwords 2024
End-to-end pipeline agility - Berlin Buzzwords 2024
DATA COMMS-NETWORKS YR2 lecture 08 NAT & CLOUD.docx
DATA COMMS-NETWORKS YR2 lecture 08 NAT & CLOUD.docx
Intelligence supported media monitoring in veterinary medicine
Intelligence supported media monitoring in veterinary medicine
Build applications with generative AI on Google Cloud
Build applications with generative AI on Google Cloud
Beyond the Basics of A/B Tests: Highly Innovative Experimentation Tactics You...
Beyond the Basics of A/B Tests: Highly Innovative Experimentation Tactics You...
Orchestrating the Future: Navigating Today's Data Workflow Challenges with Ai...
Orchestrating the Future: Navigating Today's Data Workflow Challenges with Ai...
A presentation that explain the Power BI Licensing
A presentation that explain the Power BI Licensing
Population Growth in Bataan: The effects of population growth around rural pl...
Population Growth in Bataan: The effects of population growth around rural pl...
STATATHON: Unleashing the Power of Statistics in a 48-Hour Knowledge Extravag...
STATATHON: Unleashing the Power of Statistics in a 48-Hour Knowledge Extravag...
workover
- 1. KERJA ULANG SUMUR TUGAS (SOAL DAN JAWABAN) DOSEN PEMBIMBING: IDHAM KHALID, ST.MT OLEH: ILHAM RABIKHI 123210575 KELAS B JURUSAN PERMINYAKAN FAKULTAS TEKNIK UNIVERSITAS ISLAM RIAU PEKANBARU 2015
- 2. SOAL DAN JAWABAN 1. Dari data di bawahini, buatlahkurva IPR menggunakanrumus Vogel, asumsikanpenurunanPwf setiap 500 psi: Porosity ∅ = 0.19 Effective horizontal permeability k = 8.2 md Pay zone thickness h = 53 ft Reservoir pressure P = 5,651 psia Bubble point pressure Pb = 5,651 psia Fluid formation volume factor Bo = 1.1 Fluyid viscosity μo = 1.7 cp Total compressibility ct = 0.0000129 psi−1 Drainage area A = 640 acres, re = 2,980 ft Wellbore radius rw = 0.328 ft Skin factor S = 0 Penyelesaian: Rumus Vogel: Qo Qmaks = 1 − 0.2 ( Pwf Ps ) − 0.8 ( Pwf Ps ) 2 Pwf Pwf/Pr Qo/Qmaks 5661 1.017982377 -0.032626972 5161 0.928070491 0.125334033 4661 0.838158605 0.270360402 4161 0.748246718 0.402452135 3661 0.658334832 0.521609233 3161 0.568422946 0.627831695 2661 0.478511059 0.721119521 2161 0.388599173 0.801472712 1661 0.298687286 0.868891267 1161 0.2087754 0.923375186 661 0.118863514 0.964924469 161 0.028951627 0.993539117 0 0 1
- 3. 2. Berapakahkemampuanlajualirmaksimum(Qmax) dari well KB#059 (5 Juli 2005): Total fluid proud = 3000BFPD 300 BOPD⁄ SFL = 400 ft WFL = 1500 ft Perforation depth = 4800 ft Oil = 33°API SGwater = 1.02 Penyelesaian: 𝑆𝐺 𝐹𝑙𝑢𝑖𝑑 = (1 − 𝑤𝑐) 𝑥𝑆𝐺 𝑂𝑖𝑙 + 𝑤𝑐 𝑥 𝑆𝐺 𝑤𝑎𝑡𝑒𝑟 𝑆𝐺 𝐹𝑙𝑢𝑖𝑑 = (1 − 0) 𝑥 33 + 0 𝑥 1.02 = 33 𝐺𝑟𝑎𝑑𝑖𝑒𝑛𝑡 𝑓𝑙𝑢𝑖𝑑 = 0,433 𝑥 33 0 0.2 0.4 0.6 0.8 1 1.2 -0.2 0 0.2 0.4 0.6 0.8 1 1.2 Pwf/Pr Qo/Qmaks IPR VOGEL IPR
- 4. = 0,143 𝑃𝑟 = (ℎ – 𝑆𝐹𝐿) 𝑥 𝑔𝑟𝑎𝑑𝑖𝑒𝑛𝑡 𝑓𝑙𝑢𝑖𝑑 = ( 4800 – 400 ) 𝑥 0,143 = 6,29 𝑥 102 = 629 𝑃𝑤𝑓 = (ℎ − 𝑊𝐹𝐿) 𝑥 𝑔𝑓 = ( 4800 – 1500 ) 𝑥 0,143 = 471 𝑃𝐼 = 𝑄 / (𝑃𝑟 – 𝑃𝑤𝑓) = 3000 ( 629−471 ) = 18,89 𝑄𝑚𝑎𝑥 = 𝑃𝐼 𝑥 ( 𝑃𝑟 – 0 ) = 18,98 𝑥 ( 629 – 0 ) = 11, 93 𝐵𝑃𝐹𝐷 3. Turunkan persamaan rumus PI di bawah ini dari persamaan awalnya, PI = Q (Pr − Pwf)⁄ ! PI = Q (WFL − SFL)⁄ PI = BPD psi⁄ Penyelesaian: Penurunan Rumus 𝑃𝐼 = 𝑄 (Pr −𝑃𝑤𝑓) 𝐵𝑃𝐷 𝐹𝑡⁄ 𝑃𝐼 = 𝑄 (Pr −𝑃𝑤𝑓) 𝑃𝐼 = 𝐵𝑃𝐷 𝑃𝑠𝑖 𝑃𝐼 = 𝑄 𝑊𝐹𝐿−𝑆𝐹𝐿 𝑃𝐼 = 𝑄 𝑊𝐹𝐿 − 𝑆𝐹𝐿 = 𝐵𝑃𝐷 𝐹𝑡 Makasatuan PI adalahBPD ft⁄ 𝑄 𝐵𝑃𝐷 Pr −𝑃𝑤𝑓 𝑃𝑠𝑖 𝑃𝑟 = ( ℎ – 𝑆𝐹𝐿 ) × 𝐺𝑟 = ( 𝐹𝑡 – 𝐹𝑡 ) × 𝑝𝑠𝑖 𝑓𝑡 = 𝐹𝑡 × 𝑝𝑠𝑖 𝑓𝑡 𝑃𝑟 = 𝑃𝑠𝑖 𝑃𝑟 = ( ℎ – 𝑆𝐹𝐿 ) × 𝑔𝑟 ( ℎ – 𝑆𝐹𝐿 ) = 𝑃𝑟 𝑔𝑓 𝑓𝑡 = 𝑝𝑠𝑖 𝑝𝑠𝑖 𝑓𝑡⁄ 𝑓𝑡 = 𝑓𝑡
- 5. 4. Berapakahkemampuanlajualirmaksimumdari well KB#059? Total fluid proud = 2742BFPD 137 BOPD⁄ WC = 95% SFL = 403 ft WFL = 1452 ft Perforation depth = 4807 ft Oil = 33°API SGwater = 1.02 Penyelesaian: 𝑆𝐺 𝐹𝑙𝑢𝑖𝑑 = (1 − 𝑤𝑐) 𝑥𝑆𝐺 𝑂𝑖𝑙 + 𝑤𝑐 𝑥 𝑆𝐺 𝑤𝑎𝑡𝑒𝑟 𝑆𝐺 𝐹𝑙𝑢𝑖𝑑 = (1 − 0,95 ) 𝑥 33+ 0,93 𝑥 1.02 = 2,6 𝐺𝑟𝑎𝑑𝑖𝑒𝑛𝑡 𝑓𝑙𝑢𝑖𝑑 = 0,433 𝑥 𝑆𝐺 𝑓𝑙𝑢𝑖𝑑 = 0,433 𝑥 2,6 = 1,125 𝑝𝑠𝑖 𝑓𝑡⁄ 𝑃𝑟 = (ℎ – 𝑆𝐹𝐿) 𝑥 𝑔𝑟𝑎𝑑𝑖𝑒𝑛𝑡 𝑓𝑙𝑢𝑖𝑑 = ( 4807 – 403 )𝑥 1,125 = 6,29 𝑥 102 = 4954 𝑝𝑠𝑖 𝑃𝑤𝑓 = (ℎ − 𝑊𝐹𝐿) 𝑥 𝑔𝑓 = ( 4807 – 1452 )𝑥 1,125 = 4193 𝑝𝑠𝑖 𝑃𝐼 = 𝑄 / (𝑃𝑟 – 𝑃𝑤𝑓) = 2742 ( 4954 −4193 ) = 3,6 𝑄𝑚𝑎𝑥 = 𝑃𝐼 𝑥 ( 𝑃𝑟 – 0 ) = 3,6 𝑥 ( 4954 – 0 ) = 17,834 𝐵𝑃𝐹𝐷 PI = Q Pr − Pwf = 2742 1929.83 − 1470.1608 = 5.9651 Qmaks = PI × (Pr − Pwf) = 5.9651 × (1929.83− 1470.1608) = 2742 BPD