Stability enhancement of wind power system by using energy capacitor system
•Download as DOCX, PDF•
0 likes•204 views
This paper presents Permanent Magnet Synchronous generator (PMSG) based a variable speed wind turbine systems including energy capacitor system (ECS). The ECS is the combination of electric double layer capacitor (EDLC) known as super capacitor and power electronic devices for wind power application with its detailed modeling and control strategy which can supply smooth electrical power to the power grid and makes the system better stable and reliable. As generated power from wind fluctuates randomly, the objective of this control system is to select a line power reference level and to follow the reference level by absorbing or providing active power to or from ECS to smooth output power fluctuation penetrated to the grid and to keep the wind farm terminal voltage at a desired level by supplying necessary reactive power. The performance of the proposed system is investigated by simulation analysis using PSCAD/EMTDC software.
Report
Share
Report
Share
Recommended
Solar wind hybrid system
it is very important to upgrade the knowledge so that people will update them selves to gather the knowledge to about the solar hybrid system
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
Solar pv charging station for electric vehicles
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Solar Wind Hybrid Generation System Integration with Grid
Wind and solar energy are becoming popular owing to the abundance, availability and ease of harnessing the energy for electrical power generation. This paper focuses on an integrated hybrid renewable energy system consisting of wind and solar energies. Grid tied power generation systems make use of solar PV or wind turbines to produce electricity and supply the load by connecting to the grid. In this study, the HOMER Hybrid Optimization Model for Electric Renewable MATLAB modeling has been used to model the power system, its physical behavior and its life cycle cost. Through the use of simulations, the installation of ten 2 MW wind turbines and 2.5 MW solar PV was evaluated. Shahid Ahmad Malik | Muhammad Shahid "Solar-Wind Hybrid Generation System Integration with Grid" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-2 , February 2021, URL: https://www.ijtsrd.com/papers/ijtsrd38452.pdf Paper Url: https://www.ijtsrd.com/engineering/electrical-engineering/38452/solarwind-hybrid-generation-system-integration-with-grid/shahid-ahmad-malik
Volume weight cost comparison of a 1 mva 10 kv 400v solid state against a con...
Solid-State Transformers (SSTs) are an emergent topic in the context of the Smart Grid paradigm, where SSTs could replace conventional passive transformers to add flexibility and controllability, such as power routing capabilities or reactive power compensation, to the grid. This paper presents a comparison of a 1000 kVA three-phase, low-frequency distribution transformer (LFT) and an equally rated SST, with respect to volume, weight, losses, and material costs, where the corresponding data of the SST is partly based on a full-scale prototype design. It is found that the SST’s costs are at least five times and its losses about three times higher, its weight similar but its volume reduced to less than 80 %. In addition, an AC/DC application is also considered, where the comparison turns out in favor of the SST-based concept, since its losses are only about half compared to the LFT-based system, and the volume and the weight are reduced to about one third, whereas the material costs advantage of the LFT is much less pronounced.
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
Recommended
Solar wind hybrid system
it is very important to upgrade the knowledge so that people will update them selves to gather the knowledge to about the solar hybrid system
Generation of Higher Number of Voltage Levels by Stacking Inverters of Lower ...
This paper proposes a new method of generating higher number of levels in the voltage waveform by stacking multilevel converters with lower voltage space vector structures. An important feature of this stacked structure is the use of low voltage devices while attaining higher number of levels. This will find extensive applications in electric vehicles since direct battery drive is possible. The voltages of all the capacitors in the structure can be controlled within a switching cycle using the switching state redundancies (pole voltage redundancies). This helps in reducing the capacitor size. Also, the capacitor voltages can be balanced irrespective of modulation index and load power factor. To verify the concept experimentally, a 9-level inverter is developed by stacking two 5-level inverters and an induction motor is run using V/f control scheme. Both steady state and transient results are presented.
Solar pv charging station for electric vehicles
Of late, electric vehicles (EVs) have attracted much attention owing to their use of clean energy. Large progress in lithium-ion battery has propelled the development of EVs.However, the challenge is that growing number of EVs leads to huge demand in electric power, which will aggravate the power grid load. This leads to an exploration for alternative and clean sources of energy to charge EVs. This project implements solar energy system to erect a charging station for EV application. The charging station employs multi-port charging by providing a constant voltage DC bus. The charging controllers are operated based on the concept of power balance, and constant current/constant voltage charging. Performance of the charging system is validated with simulation and experimental results.
Solar Wind Hybrid Generation System Integration with Grid
Wind and solar energy are becoming popular owing to the abundance, availability and ease of harnessing the energy for electrical power generation. This paper focuses on an integrated hybrid renewable energy system consisting of wind and solar energies. Grid tied power generation systems make use of solar PV or wind turbines to produce electricity and supply the load by connecting to the grid. In this study, the HOMER Hybrid Optimization Model for Electric Renewable MATLAB modeling has been used to model the power system, its physical behavior and its life cycle cost. Through the use of simulations, the installation of ten 2 MW wind turbines and 2.5 MW solar PV was evaluated. Shahid Ahmad Malik | Muhammad Shahid "Solar-Wind Hybrid Generation System Integration with Grid" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-2 , February 2021, URL: https://www.ijtsrd.com/papers/ijtsrd38452.pdf Paper Url: https://www.ijtsrd.com/engineering/electrical-engineering/38452/solarwind-hybrid-generation-system-integration-with-grid/shahid-ahmad-malik
Volume weight cost comparison of a 1 mva 10 kv 400v solid state against a con...
Solid-State Transformers (SSTs) are an emergent topic in the context of the Smart Grid paradigm, where SSTs could replace conventional passive transformers to add flexibility and controllability, such as power routing capabilities or reactive power compensation, to the grid. This paper presents a comparison of a 1000 kVA three-phase, low-frequency distribution transformer (LFT) and an equally rated SST, with respect to volume, weight, losses, and material costs, where the corresponding data of the SST is partly based on a full-scale prototype design. It is found that the SST’s costs are at least five times and its losses about three times higher, its weight similar but its volume reduced to less than 80 %. In addition, an AC/DC application is also considered, where the comparison turns out in favor of the SST-based concept, since its losses are only about half compared to the LFT-based system, and the volume and the weight are reduced to about one third, whereas the material costs advantage of the LFT is much less pronounced.
Development of wind and solar based ac microgrid with power quality improveme...
This work proposes a microgrid (μ-grid) integrating wind and solar photovoltaic (PV) resources, along with the battery energy storage (BES) to the three phase grid feeding the nonlinear load. The μ-grid disconcerted by probabilistic nonlinear time dependent parameters and their effects are compensated by cohesive controllers used for utility grid side voltage source converter (GVSC) and machine side VSC (MVSC). The switching controls and the reconfigurability of the μ-grid are addressed on imperative aspects of improving power quality (PQ), power reliability, nonlinear load compensation and economic utilization of resources. The nonlinear load compensation and PQ enhancement are achieved by executing modified version of the adaptive filtering technique including “momentum” based least mean square (MLMS) control technique, utilized for providing the switching control signals to the GVSC. It utilizes two preceding gradient weights for obtaining updated weight thereby improving the convergence rate and overcoming the limitation of conventional control of the same family. The MVSC acquires its switching signals from conventional vector control scheme and the encoderless estimation of speed and rotor position of the synchronous generator (SG) driven by wind turbine through back electromotive force control technique. The external environmental disturbances are overcome by utilizing perturb and observe (P&O) maximum power point (MPP) for wind optimal power extraction and adaptive P&O with variable perturbation step size for solar MPP estimation. Test results are obtained from the laboratory prototype under steady state and dynamic conditions including altering wind speed, intermittent solar insolation and variable load conditions. The PQ issues are addressed and investigated successfully.
High frequency ac-link pv inverter
In this paper, a high-frequency ac-link photovoltaic (PV) inverter is proposed. The proposed inverter overcomes most of the problems associated with currently available PV inverters. In this inverter, a single-stage power-conversion unit fulfills all the system requirements, i.e., inverting dc voltage to proper ac, stepping up or down the input voltage, maximum power point tracking, generating low-harmonic ac at the output, and input/output isolation. This inverter is, in fact, a partial resonant ac-link converter in which the link is formed by a parallel inductor/capacitor (LC) pair having alternating current and voltage. Among the significant merits of the proposed inverter are the zero-voltage turn-on and soft turn-off of the switches which result in negligible switching losses and minimum voltage stress on the switches. Hence, the frequency of the link can be as high as permitted by the switches and the processor. The high frequency of operation makes the proposed inverter very compact. The other significant advantage of the proposed inverter is that no bulky electrolytic capacitor exists at the link. Electrolytic capacitors are cited as the most unreliable component in PV inverters, and they are responsible for most of the inverters’ failures, particularly at high temperature. Therefore, substituting dc electrolytic capacitors with ac LC pairs will significantly increase the reliability of PV inverters. A 30-kW prototype was fabricated and tested. The principle of operation and detailed design procedure of the proposed inverter along with the simulation and experimental results are included in this paper. To evaluate the long-term performance of the proposed inverter, three of these inverters were installed at three different commercial facilities in Texas, USA, to support the PV systems. These inverters have been working for several months now.
An efficient modified cuk converter with fuzzy based maximum power point trac...
To improve the performance of photovoltaic system a modified cuk converter with Maximum Power Point Tracker (MPPT) that uses a fuzzy logic control algorithm is presented in this research work. In the proposed cuk converter, the conduction losses and switching losses are reduced by means of replacing the passive elements with switched capacitors. These switched capacitors are used to provide smooth transition of voltage and current. So, the conversion efficiency of the converter is improved and the efficiency of the PV system is increased. The PV systems use a MPPT to continuously extract the highest possible power and deliver it to the load. MPPT consists of a dc-dc converter used to find and maintain operation at the maximum power point using a tracking algorithm. The simulated results indicate that a considerable amount of additional power can be extracted from photovoltaic module using a proposed converter with fuzzy logic controller based MPPT
Design a Highly Efficient Push-Pull converter for Photovoltaic Applications
Design a schematic to extract maximum obtainable solar power from a PV module and use the energy for a DC application. This project investigates in detail the concept of Maximum Power Point Tracking (MPPT) which significantly increases the efficiency of the solar photovoltaic system.
Integration of Supercapacitor in Photovoltaic Energy Storage: Modelling and C...
Due to the variable characteristics of photovoltaic energy production or the variation of the load, batteries used in storage systems renewable power can undergo many irregular cycles of charge 1 discharge. In turn, this can also have a detrimental effect on the life of the battery and can increase project costs. This paper presents an embedded energy share method between the energy storage system (battery) and the auxiliary energy storage system such as supercapacitors (SC). Supercapacitors are used to improve batteries life and reduce their stresses by providing or absorbing peaks currents as demanded by the load. The photovoltaic cells are connected to DC bus with boost converter and controlled with MPPT algorithm, Supercapacitors and batteries are linked to the DC bus through the buck-boost converter. The inductive load is connected to the DC bus by a DC-AC converter. The static converters associated with batteries and supercapacitors are controlled by current. The components of the systems are supervised through a block of energy management. The complete model of the system is implemented in MATLAB/Simulink environment. Simulation results are given to show the performance of the proposed control strategy, for the overall system.
An integrated boost resonant converter for photovoltaic applications
Effective photovoltaic power conditioning requires efficient power conversion and accurate maximum power point tracking to counteract the effects of panel mismatch, shading, and general variance in power output during a daily cycle. In this paper, the authors propose an integrated boost resonant converter with low component count, galvanic isolation, simple control, as well as
high efficiency across a wide input and load range. Provided is a discussion of the converter synthesis, key operational features, converter design procedure, and loss analysis, as well as experimental verification by way of a 250-W prototype with a California Energy Commission efficiency of 96.8%.
Modified cascaded h bridge multilevel inverter for hybrid renewable energy ap...
Renewable energy sources and technologies have the potential to provide solutions to the longstanding energy problems being faced by developing countries. The renewable energy sources like wind energy, solar energy, geothermal energy, ocean energy, biomass energy and fuel cell technology can be used to overcome energy shortage in India. This paper proposes a modified multi-level inverter (MLI) topology for Hybrid Renewable Energy Sources (HRES) and a design of hybrid solar-wind power generation model with 9-level, 13-level and 17-level inverter topologies. A HRES connected to a modified Cascaded H-Bridge Multi Level Inverter (CHB-MLI) is developed, whose switches are controlled using Artificial Neural Network (ANN) model. The proposed hybrid energy system model consists of 10 Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) that intend to give 17 levels of output voltage. The proposed topology performs effectively with reduced number of components and reduced Total Harmonic Distortion (THD). The performance of the proposed system is analyzed by designing the model in MATLAB/SIMULINK environment. The simulation results of the proposed inverter for the HRES application are compared with the results of the existing topologies to show the effectiveness of the proposed model.
New ac dc power factor correction architecture suitable for high frequency op...
This paper presents a novel ac-dc power factor correction (PFC) power conversion architecture for single-phase grid interface. The proposed architecture has significant advantages for achieving high efficiency, good power factor, and converter miniaturization, especially in low-to-medium power applications. The architecture enables twice-line-frequency energy to be buffered at high voltage with a large voltage swing, enabling reduction in the energy buffer capacitor size, and elimination of electrolytic capacitors. While this architecture can be beneficial with a variety of converter topologies, it is especially suited for system miniaturization by enabling designs that operate at high frequency (HF, 3 – 30 MHz). Moreover, we introduce circuit implementations that provide efficient operation in this range. The proposed approach is demonstrated for an LED driver converter operating at a (variable) HF switching frequency (3 – 10 MHz) from 120Vac, and supplying a 35Vdc output at up to 30W. The prototype converter achieves high efficiency (92 %) and power factor (0.89), and maintains good performance over a wide load range. Owing to architecture and HF operation, the prototype achieves a high ‘box’ power density of 50W/ in3 (‘displacement’ power density of 130W/ in3), with miniaturized inductors, ceramic energy buffer capacitors, and a small-volume EMI filter.
Power management strategy for a multi hybrid fuel cell energy storage power ...
This paper depicts a new configuration for modular hybrid power conversion systems, namely, multi-hybrid generation system (MHGS), and parallel connection at the output, such that the converter of each unit shares the load current equally. This is a significant step towards realizing a modular power conversion system architecture, where smaller units can be connected in any series/parallel grouping to realize any required unit specifications. The supercapacitor (SC) as a complementary source is used to compensate for the slow transient response of the fuel cell (FC) as a main power source. It assists the Fe to meet the grid power demand in order to achieve a better performance and dynamic behavior. Reliable control of the proposed MHGS with multiple units is also a challenging issue. In this paper, a simple control method to achieve active sharing of load current among MHGS modules is proposed. The simulation results verify the performance of the proposed structure and control scheme.
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
Control strategy for power flow management in a pv system supplying dc loads
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
ECE ROLE OF SOLAR FARM IN POWER FACTOR IMPROVEMENT OF GRID CONNECTED SYSTEM
Role of solar farm in power factor improvement of grid connected system.
introduction
how do solar panels work what is power factor with example
and conclusion.
A Simple Active and Reactive Power Control for Applications of Single-Phase E...
Aiming at effective power management in microgrids with high penetration of renewable energy sources (RESs), the paper proposes a simple power control for the so-called second-generation, single-phase electric springs (ES-2), that overcomes the shortcomings of the existing ES control methods. By the proposed control, the unpredictable power generated from RESs is divided into two parts, i.e. the one absorbed by the ES-2 that still varies and the other injected into the grid that turns to be controllable, by a simple and accurate signal manipulation that works both at steady-state and during RES transients. It is believed that such a control is suitable for the distributed power generation, especially at domestic homes.
In the paper, the proposed control is supported by a theoretical background. Its effectiveness is at first validated by simulations and then by experiments. To this purpose, a typical RES application is considered, and an experimental setup is arranged, built up around an ES-2 implementing the proposed control. Testing of the setup is carried out in three steps and proves not only the smooth operation of the ES-2 itself, but also its capability in running the application properly.
Dynamic modeling of microgrid for grid connected intentional islanding operat...
Microgrid is defined as the cluster of multiple distributed generators (DGs) such as renewable energy sources that supply electrical energy. The connection of microgrid is in parallel with the main grid. When microgrid is isolated from remainder of the utility system, it is said to be in intentional islanding mode. In this mode, DG inverter system operates in voltage control mode to provide constant voltage to the local load. During grid connected mode, the Microgrid operates in constant current control mode to supply preset power to the main grid. The main contribution of this paper is summarized as
1) Design of a network based control scheme for inverter based sources, which provides proper current control during grid connected mode and voltage control during islanding mode.
2) Development of an algorithm for intentional islanding detection and synchronization controller required during grid reconnection.
3) Dynamic modeling and simulation are conducted to show system behavior under proposed method using SIMULINK.
From the simulation results using Simulink dynamic models, it can be shown that these controllers provide the microgrid with a deterministic and reliable connection to the grid.
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
In this paper, by using a modular hybrid structure, a new topology for symmetric multilevel inverters (MLI) with a small number of semiconductors and low voltage stress across switches is proposed. Despite many other topologies, this topology can inherently produce negative levels and zero levels without using the H-bridge. The voltage stress across a particular switch of the proposed MLI is inversely proportional to the number of the switching of that switch in a voltage period. The proposed structure is based on two types of module, that is, the f-module and the e-module. The e-module uses a capacitive voltage divider to double the number of non-zero levels. The voltages of the capacitors are approximately balanced without complex control methods. The basic structure of the proposed topology is formed by connecting the f-module and the e-module in series with each other, and the cascaded topology is developed by cascading multiple f-modules with an e-module. To investigate the proposed topology and proving its practicability, simulation results with MATLAB/Simulink, investigation of the capacitor voltages, loss calculations and experimental results are presented. A comparative study is also performed to show the merit of the new multilevel inverter over other topologies.
Power flow control of hybrid micro grids using modified uipc
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
A Hybrid AC/DC Micro grid and Its Coordination Control
The microgrid concept introduces the reduction of multiple conversions in an individual AC or DC grid and also facilitates connections to variable renewable AC and DC sources and loads to power system.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
In this paper, a novel algorithm, based on dc link voltage, is proposed for effective energy management of a standalone permanent magnet synchronous generator (PMSG)-based variable speed wind energy conversion system consisting of battery, fuel cell, and dump load (i.e., electrolyzer). Moreover, by maintaining the dc link voltage at its reference value, the output ac voltage of the inverter can be kept constant irrespective of variations in the wind speed and load. An effective control technique for the inverter, based on the pulse width modulation (PWM) scheme, has been developed to make the line voltages at the point of common coupling (PCC) balanced when the load is unbalanced. Similarly, a proper control of battery current through dc–dc converter has been carried out to reduce the electrical torque pulsation of the PMSG under an unbalanced load scenario. Based on extensive simulation results using MATLAB/SIMULINK, it has been established that the performance of the controllers both in transient as well as in steady state is quite satisfactory and it can also maintain maximum power point tracking.
More Related Content
What's hot
High frequency ac-link pv inverter
In this paper, a high-frequency ac-link photovoltaic (PV) inverter is proposed. The proposed inverter overcomes most of the problems associated with currently available PV inverters. In this inverter, a single-stage power-conversion unit fulfills all the system requirements, i.e., inverting dc voltage to proper ac, stepping up or down the input voltage, maximum power point tracking, generating low-harmonic ac at the output, and input/output isolation. This inverter is, in fact, a partial resonant ac-link converter in which the link is formed by a parallel inductor/capacitor (LC) pair having alternating current and voltage. Among the significant merits of the proposed inverter are the zero-voltage turn-on and soft turn-off of the switches which result in negligible switching losses and minimum voltage stress on the switches. Hence, the frequency of the link can be as high as permitted by the switches and the processor. The high frequency of operation makes the proposed inverter very compact. The other significant advantage of the proposed inverter is that no bulky electrolytic capacitor exists at the link. Electrolytic capacitors are cited as the most unreliable component in PV inverters, and they are responsible for most of the inverters’ failures, particularly at high temperature. Therefore, substituting dc electrolytic capacitors with ac LC pairs will significantly increase the reliability of PV inverters. A 30-kW prototype was fabricated and tested. The principle of operation and detailed design procedure of the proposed inverter along with the simulation and experimental results are included in this paper. To evaluate the long-term performance of the proposed inverter, three of these inverters were installed at three different commercial facilities in Texas, USA, to support the PV systems. These inverters have been working for several months now.
An efficient modified cuk converter with fuzzy based maximum power point trac...
To improve the performance of photovoltaic system a modified cuk converter with Maximum Power Point Tracker (MPPT) that uses a fuzzy logic control algorithm is presented in this research work. In the proposed cuk converter, the conduction losses and switching losses are reduced by means of replacing the passive elements with switched capacitors. These switched capacitors are used to provide smooth transition of voltage and current. So, the conversion efficiency of the converter is improved and the efficiency of the PV system is increased. The PV systems use a MPPT to continuously extract the highest possible power and deliver it to the load. MPPT consists of a dc-dc converter used to find and maintain operation at the maximum power point using a tracking algorithm. The simulated results indicate that a considerable amount of additional power can be extracted from photovoltaic module using a proposed converter with fuzzy logic controller based MPPT
Design a Highly Efficient Push-Pull converter for Photovoltaic Applications
Design a schematic to extract maximum obtainable solar power from a PV module and use the energy for a DC application. This project investigates in detail the concept of Maximum Power Point Tracking (MPPT) which significantly increases the efficiency of the solar photovoltaic system.
Integration of Supercapacitor in Photovoltaic Energy Storage: Modelling and C...
Due to the variable characteristics of photovoltaic energy production or the variation of the load, batteries used in storage systems renewable power can undergo many irregular cycles of charge 1 discharge. In turn, this can also have a detrimental effect on the life of the battery and can increase project costs. This paper presents an embedded energy share method between the energy storage system (battery) and the auxiliary energy storage system such as supercapacitors (SC). Supercapacitors are used to improve batteries life and reduce their stresses by providing or absorbing peaks currents as demanded by the load. The photovoltaic cells are connected to DC bus with boost converter and controlled with MPPT algorithm, Supercapacitors and batteries are linked to the DC bus through the buck-boost converter. The inductive load is connected to the DC bus by a DC-AC converter. The static converters associated with batteries and supercapacitors are controlled by current. The components of the systems are supervised through a block of energy management. The complete model of the system is implemented in MATLAB/Simulink environment. Simulation results are given to show the performance of the proposed control strategy, for the overall system.
An integrated boost resonant converter for photovoltaic applications
Effective photovoltaic power conditioning requires efficient power conversion and accurate maximum power point tracking to counteract the effects of panel mismatch, shading, and general variance in power output during a daily cycle. In this paper, the authors propose an integrated boost resonant converter with low component count, galvanic isolation, simple control, as well as
high efficiency across a wide input and load range. Provided is a discussion of the converter synthesis, key operational features, converter design procedure, and loss analysis, as well as experimental verification by way of a 250-W prototype with a California Energy Commission efficiency of 96.8%.
Modified cascaded h bridge multilevel inverter for hybrid renewable energy ap...
Renewable energy sources and technologies have the potential to provide solutions to the longstanding energy problems being faced by developing countries. The renewable energy sources like wind energy, solar energy, geothermal energy, ocean energy, biomass energy and fuel cell technology can be used to overcome energy shortage in India. This paper proposes a modified multi-level inverter (MLI) topology for Hybrid Renewable Energy Sources (HRES) and a design of hybrid solar-wind power generation model with 9-level, 13-level and 17-level inverter topologies. A HRES connected to a modified Cascaded H-Bridge Multi Level Inverter (CHB-MLI) is developed, whose switches are controlled using Artificial Neural Network (ANN) model. The proposed hybrid energy system model consists of 10 Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) that intend to give 17 levels of output voltage. The proposed topology performs effectively with reduced number of components and reduced Total Harmonic Distortion (THD). The performance of the proposed system is analyzed by designing the model in MATLAB/SIMULINK environment. The simulation results of the proposed inverter for the HRES application are compared with the results of the existing topologies to show the effectiveness of the proposed model.
New ac dc power factor correction architecture suitable for high frequency op...
This paper presents a novel ac-dc power factor correction (PFC) power conversion architecture for single-phase grid interface. The proposed architecture has significant advantages for achieving high efficiency, good power factor, and converter miniaturization, especially in low-to-medium power applications. The architecture enables twice-line-frequency energy to be buffered at high voltage with a large voltage swing, enabling reduction in the energy buffer capacitor size, and elimination of electrolytic capacitors. While this architecture can be beneficial with a variety of converter topologies, it is especially suited for system miniaturization by enabling designs that operate at high frequency (HF, 3 – 30 MHz). Moreover, we introduce circuit implementations that provide efficient operation in this range. The proposed approach is demonstrated for an LED driver converter operating at a (variable) HF switching frequency (3 – 10 MHz) from 120Vac, and supplying a 35Vdc output at up to 30W. The prototype converter achieves high efficiency (92 %) and power factor (0.89), and maintains good performance over a wide load range. Owing to architecture and HF operation, the prototype achieves a high ‘box’ power density of 50W/ in3 (‘displacement’ power density of 130W/ in3), with miniaturized inductors, ceramic energy buffer capacitors, and a small-volume EMI filter.
Power management strategy for a multi hybrid fuel cell energy storage power ...
This paper depicts a new configuration for modular hybrid power conversion systems, namely, multi-hybrid generation system (MHGS), and parallel connection at the output, such that the converter of each unit shares the load current equally. This is a significant step towards realizing a modular power conversion system architecture, where smaller units can be connected in any series/parallel grouping to realize any required unit specifications. The supercapacitor (SC) as a complementary source is used to compensate for the slow transient response of the fuel cell (FC) as a main power source. It assists the Fe to meet the grid power demand in order to achieve a better performance and dynamic behavior. Reliable control of the proposed MHGS with multiple units is also a challenging issue. In this paper, a simple control method to achieve active sharing of load current among MHGS modules is proposed. The simulation results verify the performance of the proposed structure and control scheme.
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
The presence of harmonics in solar Photo Voltaic (PV) energy conversion system results in deterioration of power quality. To address such issue, this paper aims to investigate the elimination of harmonics in a solar fed cascaded fifteen level inverter with aid of Proportional Integral (PI), Artificial Neural Network (ANN) and Fuzzy Logic (FL) based controllers. Unlike other techniques, the proposed FLC based approach helps in obtaining reduced harmonic distortions that intend to an enhancement in power quality. In addition to the power quality improvement, this paper also proposed to provide output voltage regulation in terms of maintaining voltage and frequency at the inverter output end in compatible with the grid connection requirements. The simulations are performed in the MATLAB / Simulink environment for solar fed cascaded 15 level inverter incorporating PI, ANN and FL based controllers. To exhibit the proposed technique, a 3 kWp photovoltaic plant coupled to multilevel inverter is designed and hardware is demonstrated. All the three techniques are experimentally investigated with the measurement of power quality metrics along with establishing output voltage regulation.
Control strategy for power flow management in a pv system supplying dc loads
The growing concern for energy saving has increased the usage of LED-based street lights, electronic chokes, compact fluorescent lamps, and inverter-fed drives. Hence, the load profile seen by the electrical grid is undergoing a notable change as these devices have to operate from a dc source. Photovoltaics (PV) being a major energy source, the aforementioned loads can be connected directly to the dc bus. A grid-connected PV system involves a power source (PV array), a power sink (load), and two power sources/sink (utility and battery), and hence, a power
flow management system is required to balance the power flow among these sources. One such system is developed for selecting the operating mode of the bidirectional converter by sensing the battery voltage. The viability of the scheme has been ascertained by performing experimental studies on a laboratory prototype. The control strategy is digitally implemented on an Altera Cyclone II Field Programmable Gate Array (FPGA) board, and the algorithm is verified for different modes of operation by varying the load. Experimental results are presented to bring out
the usefulness of the control strategy.
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
Battery storage is usually employed in Photovoltaic (PV) system to mitigate the power fluctuations due to the characteristics of PV panels and solar irradiance. Control schemes for PV-battery systems must be able to stabilize the bus voltages as well as to control the power flows flexibly. This paper proposes a comprehensive control and power management system (CAPMS) for PV-battery-based hybrid microgrids with both AC and DC buses, for both grid-connected and islanded modes. The proposed CAPMS is successful in regulating the DC and AC bus voltages and frequency stably, controlling the voltage and power of each unit flexibly, and balancing the power flows in the systems automatically under different operating circumstances, regardless of disturbances from switching operating modes, fluctuations of irradiance and temperature, and change of loads. Both simulation and experimental case studies are carried out to verify the performance of the proposed method.
ECE ROLE OF SOLAR FARM IN POWER FACTOR IMPROVEMENT OF GRID CONNECTED SYSTEM
Role of solar farm in power factor improvement of grid connected system.
introduction
how do solar panels work what is power factor with example
and conclusion.
A Simple Active and Reactive Power Control for Applications of Single-Phase E...
Aiming at effective power management in microgrids with high penetration of renewable energy sources (RESs), the paper proposes a simple power control for the so-called second-generation, single-phase electric springs (ES-2), that overcomes the shortcomings of the existing ES control methods. By the proposed control, the unpredictable power generated from RESs is divided into two parts, i.e. the one absorbed by the ES-2 that still varies and the other injected into the grid that turns to be controllable, by a simple and accurate signal manipulation that works both at steady-state and during RES transients. It is believed that such a control is suitable for the distributed power generation, especially at domestic homes.
In the paper, the proposed control is supported by a theoretical background. Its effectiveness is at first validated by simulations and then by experiments. To this purpose, a typical RES application is considered, and an experimental setup is arranged, built up around an ES-2 implementing the proposed control. Testing of the setup is carried out in three steps and proves not only the smooth operation of the ES-2 itself, but also its capability in running the application properly.
Dynamic modeling of microgrid for grid connected intentional islanding operat...
Microgrid is defined as the cluster of multiple distributed generators (DGs) such as renewable energy sources that supply electrical energy. The connection of microgrid is in parallel with the main grid. When microgrid is isolated from remainder of the utility system, it is said to be in intentional islanding mode. In this mode, DG inverter system operates in voltage control mode to provide constant voltage to the local load. During grid connected mode, the Microgrid operates in constant current control mode to supply preset power to the main grid. The main contribution of this paper is summarized as
1) Design of a network based control scheme for inverter based sources, which provides proper current control during grid connected mode and voltage control during islanding mode.
2) Development of an algorithm for intentional islanding detection and synchronization controller required during grid reconnection.
3) Dynamic modeling and simulation are conducted to show system behavior under proposed method using SIMULINK.
From the simulation results using Simulink dynamic models, it can be shown that these controllers provide the microgrid with a deterministic and reliable connection to the grid.
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
A new topology of a hybrid distributed generator based on photovoltaic and wind-driven permanent magnet synchronous generator is proposed. In this generator, the sources are connected together to the grid with the help of only a single boost converter followed by an inverter. Thus, compared to earlier schemes, the proposed scheme has fewer power converters. A model of the proposed scheme in the d − q-axis reference frame is developed. Two low-cost controllers are also proposed for the new hybrid scheme to separately trigger the dc–dc converter and the inverter for tracking the maximum power from both sources. The integrated operations of both proposed controllers for different conditions are demonstrated through simulation and experimentation. The steady-state performance of the system and the transient response of the controllers are also presented to demonstrate the successful operation of the new hybrid system. Comparisons of experimental and simulation results are given to validate the simulation model.
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
In this paper, by using a modular hybrid structure, a new topology for symmetric multilevel inverters (MLI) with a small number of semiconductors and low voltage stress across switches is proposed. Despite many other topologies, this topology can inherently produce negative levels and zero levels without using the H-bridge. The voltage stress across a particular switch of the proposed MLI is inversely proportional to the number of the switching of that switch in a voltage period. The proposed structure is based on two types of module, that is, the f-module and the e-module. The e-module uses a capacitive voltage divider to double the number of non-zero levels. The voltages of the capacitors are approximately balanced without complex control methods. The basic structure of the proposed topology is formed by connecting the f-module and the e-module in series with each other, and the cascaded topology is developed by cascading multiple f-modules with an e-module. To investigate the proposed topology and proving its practicability, simulation results with MATLAB/Simulink, investigation of the capacitor voltages, loss calculations and experimental results are presented. A comparative study is also performed to show the merit of the new multilevel inverter over other topologies.
Power flow control of hybrid micro grids using modified uipc
Neuro Fuzzy Inference System (ANFIS) controlled modified Unified Inter-Phase Power Controller (UIPC). For study, a classic hybrid micro-grid connected to grid comprising of a AC micro-grid and a DC micro-grid is taken into account. These micro-grids are interconnected employing a modified UIPC, rather than using the power converters connected in parallel. As the first input of this paper is the standard structure of UIPC, which used three power converters in every phase. It was then modified such as number of power converters is used less and implemented for the control of the exchange of power between AC-DC microgrids. In every phase there is one power electronic converter in the improved structure. It is called as Line Power Converter (LPC). Also there is Bus Power Converter (BPC) to regulate the voltage of the DC bus. The Line Power Converters links the AC micro-grid to the main grid. The DC buses are also linked with them. It can be operated in Inductance Mode (IM) as well as Capacitance Mode (CM). The control structure of LPCs has an Adaptive Fuzzy Logic Controller in it. For hybrid micro-grids, the capability of the suggested power flow control strategy is confirmed by the MATLAB simulation results.
A Hybrid AC/DC Micro grid and Its Coordination Control
The microgrid concept introduces the reduction of multiple conversions in an individual AC or DC grid and also facilitates connections to variable renewable AC and DC sources and loads to power system.
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Electricity generation from the wind and solar photovoltaic (PV) systems are highly dependent upon weather conditions. Their intermittent nature leads to fluctuations in their output. Therefore, the need for rapid compensation for energy transmission and distribution systems is increasingly important. Static Synchronous Compensator (STATCOM) can be adopted for reactive power compensation and for decreasing the voltage fluctuation caused by the system and renewable energy sources. This study presents modelling of a Solar PV-Wind Hybrid Micro-grid and the increase of the stable operating limit of the system in case of the incorporation of STATCOM is examined. The major contribution of this paper is the optimization of gain parameters of four PI controllers in STATCOM control circuit based on genetic algorithms (GA) and Bacteria Foraging Algorithm (BFA) and therefore obtaining better responses and voltage stability in terms of nonlinear nature of solar-wind hybrid micro-grid. The Simulink models of the system architecture include a wind turbine model, a solar PV power system model and a STATCOM. It is certified that the voltage fluctuation at the end of the bus bar is reduced by 8% using conventional PI controller, by 10% for GA-based PI controller, and by 15% for BFA based PI controller under variable load. The results obtained by GA and BFA-based optimization of PI controllers are compared with that of the conventional controller and better results attained.
What's hot (20)
An efficient modified cuk converter with fuzzy based maximum power point trac...
An efficient modified cuk converter with fuzzy based maximum power point trac...
Design a Highly Efficient Push-Pull converter for Photovoltaic Applications
Design a Highly Efficient Push-Pull converter for Photovoltaic Applications
Integration of Supercapacitor in Photovoltaic Energy Storage: Modelling and C...
Integration of Supercapacitor in Photovoltaic Energy Storage: Modelling and C...
An integrated boost resonant converter for photovoltaic applications
An integrated boost resonant converter for photovoltaic applications
Modified cascaded h bridge multilevel inverter for hybrid renewable energy ap...
Modified cascaded h bridge multilevel inverter for hybrid renewable energy ap...
New ac dc power factor correction architecture suitable for high frequency op...
New ac dc power factor correction architecture suitable for high frequency op...
Power management strategy for a multi hybrid fuel cell energy storage power ...
Power management strategy for a multi hybrid fuel cell energy storage power ...
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Power Quality Improvement in Solar Fed Cascaded Multilevel Inverter with Outp...
Control strategy for power flow management in a pv system supplying dc loads
Control strategy for power flow management in a pv system supplying dc loads
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
A Unified Control and Power Management Scheme for PV-Battery-Based Hybrid Mic...
ECE ROLE OF SOLAR FARM IN POWER FACTOR IMPROVEMENT OF GRID CONNECTED SYSTEM
ECE ROLE OF SOLAR FARM IN POWER FACTOR IMPROVEMENT OF GRID CONNECTED SYSTEM
A Simple Active and Reactive Power Control for Applications of Single-Phase E...
A Simple Active and Reactive Power Control for Applications of Single-Phase E...
Dynamic modeling of microgrid for grid connected intentional islanding operat...
Dynamic modeling of microgrid for grid connected intentional islanding operat...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Mppt with single dc–dc converter and inverter for grid connected hybrid wind-...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
Novel symmetric modular hybrid multilevel inverter with reduced number of sem...
Power flow control of hybrid micro grids using modified uipc
Power flow control of hybrid micro grids using modified uipc
A Hybrid AC/DC Micro grid and Its Coordination Control
A Hybrid AC/DC Micro grid and Its Coordination Control
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Modelling and voltage control of the solar wind hybrid micro-grid with optimi...
Similar to Stability enhancement of wind power system by using energy capacitor system
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
This paper proposes a novel 3- stand-alone solar PV system configuration that uses high gain, high efficiency (96%) dc-dc converters both in the forward power stage as well as the bidirectional battery interface. The high voltage gain converters enable the use of low voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. Also, the proposed configuration facilitates "required power tracking (RPT)" of the PV source as per the load requirements eliminating the use of expensive and 'difficult to manage' dump loads. High performance inverter operation is achieved through abc to dq reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulse width modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation and experimental results of this work are presented.
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
In this paper, a novel algorithm, based on dc link voltage, is proposed for effective energy management of a standalone permanent magnet synchronous generator (PMSG)-based variable speed wind energy conversion system consisting of battery, fuel cell, and dump load (i.e., electrolyzer). Moreover, by maintaining the dc link voltage at its reference value, the output ac voltage of the inverter can be kept constant irrespective of variations in the wind speed and load. An effective control technique for the inverter, based on the pulse width modulation (PWM) scheme, has been developed to make the line voltages at the point of common coupling (PCC) balanced when the load is unbalanced. Similarly, a proper control of battery current through dc–dc converter has been carried out to reduce the electrical torque pulsation of the PMSG under an unbalanced load scenario. Based on extensive simulation results using MATLAB/SIMULINK, it has been established that the performance of the controllers both in transient as well as in steady state is quite satisfactory and it can also maintain maximum power point tracking.
Simulation and analysis of perturb and observe mppt algorithm for array using...
This paper presents the comparative analysis between constant duty cycle and Perturb & Observe (P&O) algorithm for extracting the power from Photovoltaic Array (PVA). Because of nonlinear characteristics of PV cell, the maximum power can be extract under particular voltage condition. Therefore, Maximum Power Point Tracking (MPPT) algorithms are used in PVA to maximize the output power. In this paper the MPPT algorithm is implemented using Ćuk converter. The dynamics of PVA is simulated at different solar irradiance and cell temperature. The P&O MPPT technique is a direct control method enables ease to implement and less complexity.
Single-phase solar PV system with battery and exchange of power in grid-conne...
A grid tied photovoltaic (PV) power conversion topology is presented in this study with a novel scheme of resynchronization to the grid. This scheme serves the purpose of supplying continuous power to the load along with feeding power to the grid. The control approach helps in mitigation of harmonics and improving the power quality while extracting the optimum power from the PV array. Depending on the availability of grid voltage, the proposed configuration is controlled using three approaches, defined as grid current control, Point of Common Coupling (PCC) voltage control and intentional islanding with re-synchronisation. A simple proportional integral controller manages the grid current, load voltage, battery current and DC Direct Current (DC) link voltage within these modes. Moreover, a control scheme for quick and smooth transitions among the modes is described. The robustness of the system under erratic behaviour of solar insolation, load power and disturbances in grid supply makes it a suitable choice for a residential application. The control, design and simulation results are presented to demonstrate the satisfactory operation of the proposed system.
A Management of power flow for DC Microgrid with Solar and Wind Energy Sources
Today there is a rapid proliferation of DC loads into the market and DC micro grid with renewable energy sources is emerging as a possible solution to meet growing energy demand. As different energy sources like solar, wind, fuel cell, and diesel generators can be integrated into the DC grid, Management of power flow among the sources is essential. In this paper, a control strategy for Management of power flow in DC micro grid with solar and wind energy sources is presented. As the regulation of voltage profile is important in a standalone system, a dedicated converter is to be employed for maintaining the DC link voltage. DC link voltage is regulated by the battery circuit while maximum power is extracted from Solar and Wind to feed the loads connected at the DC bus. A power flow algorithm is developed to control among three sources in the DC Microgrid. The algorithm is tested for various load conditions and for fluctuations in solar and wind power in MATLAB/SIMULINK environment.
An advanced multilevel converter topology with Reduced switching elements
Smart grid applications, renewable energy utilization and electric vehicles (EVs) are attracting researchers due to their importance nowadays as well as in the future. An efficient power electronic converter is a main and common topic for research in this area. In this paper, a prototype of the electrical part of a power-train for EVs using an advanced multilevel converter topology is introduced, discussed and analysed. A comparison between the advanced converter, two-level and conventional multilevel converter topology is discussed as well. A switch function model is derived and discussed for the proposed converter. A mathematical model for the converter supplied by a fuel-cell (FC) and boost-converter (BC) is implemented with Matlab/Simulink. The simulation results are analysed to evaluate the converter. The evaluation is based on the harmonic analysis and power loss calculations. The converters are tested at different switching frequencies to show the effect of this variable on the converter loss. The results indicate that the proposed converter is 1.32% more efficient compared to conventional five-level DCC. Moreover, the lowest harmonic content, for all of the studied converters, is the proposed one
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
This paper deals with a three-phase two-stage grid tied SPV (solar photo-voltaic) system. The first stage is a boost converter, which serves the purpose of MPPT (maximum power point tracking) and feeding the extracted solar energy to the DC link of the PV inverter, whereas the second stage is a two-level VSC (voltage source converter) serving as PV inverter which feeds power from a boost converter into the grid. The proposed system uses an adaptive DC link voltage which is made adaptive by adjusting reference DC link voltage according to CPI (common point of interconnection) voltage. The adaptive DC link voltage control helps in the reduction of switching power losses. A feed forward term for solar contribution is used to improve the dynamic response. The system is tested considering realistic grid voltage variations for under voltage and over voltage. The performance improvement is verified experimentally. The proposed system is advantageous not only in cases of frequent and sustained under voltage (as in the cases of far radial ends of Indian grid) but also in case of normal voltages at CPI. The THD (total harmonics distortion) of grid current has been found well under the limit of an IEEE-519 standard.
A 5-level High Efficiency Low Cost Hybrid Neutral Point Clamped Transformerle...
With the increase in the level of solar energy integration into the power grid, there arises a need for highly efficient multilevel transformerless grid connected inverter which is able to inject more power into the grid. In this paper, a novel 5-level Hybrid Neutral Point Clamped transformerless inverter topology is proposed which has no inherent ground leakage current. The proposed inverter is analyzed in detail and its switching pattern to generate multilevel output is discussed. The proposed inverter is compared with some popular transformerless inverter topologies. Simulations and experiments results confirm the feasibility and good performance of the proposed inverter.
Electric Springs A New Smart Grid Technology
The scientific principle of “mechanical springs” was described by the British physicist Robert
Hooke in the 1660’s. Since then, there has not been any further development of the Hooke’s law
in the electric regime. In this paper, this technological gap is filled by the development of
“electric springs.” The scientific principle, the operating modes, the limitations, and the practical
realization of the electric springs are reported. It is discovered that such novel concept has huge
potential in stabilizing future power systems with substantial penetration of intermittent
renewable energy sources. This concept has been successfully demonstrated in a practical power
system setup fed by an ac power source with a fluctuating wind energy source. The electric
spring is found to be effective in regulating the mains voltage despite the fluctuation caused by
the intermittent nature of wind power. Electric appliances with the electric springs embedded can
be turned into a new generation of smart loads, which have their power demand following the
power generation profile. It is envisaged that electric springs, when distributed over the power
grid, will offer a new form of power system stability solution that is independent of information
and communication technology.
Statcom for improved dynamic performance of wind farms in power grid
Application of FACTS controller called Static Synchronous Compensator STATCOM to improve the performance of power grid with Wind Farms is investigated .The essential feature of the STATCOM is that it has the ability to absorb or inject fastly the reactive power with power grid . Therefore the voltage regulation of the power grid with STATCOM FACTS device is achieved. Moreover restoring the stability of the power system having wind farm after occurring
severe disturbance such as faults or wind farm mechanical power variation is obtained with STATCOM controller . The dynamic model of the power system having wind farm controlled by
proposed STATCOM is developed . To Validate the powerful of the STATCOM FACTS controller , the studied power system is simulated and subjected to different severe disturbances . The results prove the effectiveness of the proposed STATCOM controller in terms of fast damping the power system oscillations and restoring the power system stability .
Modeling, Control, and Performance Evaluation of Grid-Tied Hybrid PV/Wind Pow...
The potential for utilizing clean energy technologies in Egypt is excellent given the abundant
solar irradiation and wind resources. This paper provides detailed design, control strategy, and performance evaluation of a grid-connected large-scale PV/wind hybrid power system in Gabel El-Zeit region located along the coast of the Red Sea, Egypt. The proposed hybrid power system consists of 50 MW PV station and 200 MW wind farm and interconnected with the electrical grid through the main Point of Common Coupling (PCC) busbar to enhance the system performance. The hybrid power system is controlled to operate at the unity power factor and also the Maximum Power Point Tracking (MPPT) technique is applied to extract the maximum power during the climatic conditions changes. Modeling and simulation of the hybrid power system have been performed using MATLAB/SIMULINK environment. Moreover, the paper presented a comprehensive case study about the realistic monthly variations of solar irradiance and wind speed in the study region to validate the effectiveness of the proposed MPPT techniques and the used control strategy. The simulation results illustrate that the total annual electricity generation from the hybrid power system is 1509.85 GWh/year, where 118.15 GWh/year (7.83 %) generates from the PV station and 1391.7 GWh/year (92.17%) comes from the wind farm. Furthermore, the hybrid power system successfully operates at the unity power factor since the injected reactive power is kept at zero.
Maximum power extraction from wind energy system based on fuzzy logic control
This paper proposes a variable speed control scheme for grid-connected wind energy conversion system (WECS) using permanent magnet synchronous generator (PMSG). The control algorithm tracks the maximum power for wind speeds below rated speed of wind turbines and ensures the power will not go over the rated power for wind speeds over the rated value. The control algorithm employs fuzzy logic controller (FLC) to effectively do this target. The wind turbine is connected to the grid via back-to-back PWM-VSC. Two effective computer simulation packages (PSIM and Simulink) are used to carry out the simulation effectively. The control system has two controllers for generator side and grid side converters. The main function of the generator side controller is to track the maximum power through controlling the rotational speed of the wind turbine using FLC. In the grid side converter, active and reactive power control has been achieved by controlling q-axis and d-axis current components, respectively. The d-axis current is set at zero for unity power factor and the q-axis current is controlled to deliver the power flowing from the dc-link to the electric utility grid.
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
In this paper wind energy conservation system (WECS) with shunt active power filter (SAPF) is proposed for harmonics elimination, power factor correction, reactive power compensation and grid current balancing. Adaptive neuro fuzzy inference system (ANFIS) based controller is implemented at WECS side to control the boost converter to achieve MPP and at SAPF sides to minimize voltage variations and enhance power quality. Here, synchronous reference frame (SRF) theory based reference current generation technique is employed in SAPF. The proposed scheme is implemented in MATLAB/Simulink. The results confirm that this method has better performance and can maintain total harmonic distortion (THD) level of the system within the IEEE standard 519.
Modeling, Control, and Performance Evaluation of Grid-Tied Hybrid PV/Wind Pow...
The potential for utilizing clean energy technologies in Egypt is excellent given the abundant solar irradiation and wind resources. This paper provides detailed design, control strategy, and performance evaluation of a grid-connected large-scale PV/wind hybrid power system in Gabel El-Zeit region located along the coast of the Red Sea, Egypt. The proposed hybrid power system consists of 50 MW PV station and 200 MW wind farm and interconnected with the electrical grid through the main Point of Common Coupling (PCC) busbar to enhance the system performance. The hybrid power system is controlled to operate at the unity power factor and also the Maximum Power Point Tracking (MPPT) technique is applied to extract the maximum power during the climatic conditions changes. Modeling and simulation of the hybrid power system have been performed using MATLAB/SIMULINK environment. Moreover, the paper presented a comprehensive case study about the realistic monthly variations of solar irradiance and wind speed in the study region to validate the effectiveness of the proposed MPPT techniques and the used control strategy. The simulation results illustrate that the total annual electricity generation from the hybrid power system is 1509.85 GWh/year, where 118.15 GWh/year (7.83 %) generates from the PV station and 1391.7 GWh/year (92.17%) comes from the wind farm. Furthermore, the hybrid power system successfully operates at the unity power factor since the injected reactive power is kept at zero.
Control of a Three-Phase Hybrid Converter for a PV Charging Station
Hybrid boost converter (HBC) has been proposed to replace a dc/dc boost converter and a dc/ac converter to reduce conversion stages and switching loss. In this paper, control of a three-phase HBC in a PV charging station is designed and tested. This HBC interfaces a PV system, a dc system with hybrid plugin electrical vehicles (HPEVs) and a three-phase ac grid. The control of the HBC is designed to realize maximum power point tracking (MPPT) for PV, dc bus voltage regulation, and ac voltage or reactive power regulation. A test bed with power electronics switching details is built in MATLAB/SimPowersystems for validation. Simulation results demonstrate the feasibility of the designed control architecture. Finally, lab experimental testing is conducted to demonstrate HBC’s control performance.
Dual-function PV-ECS integrated to 3P4W distribution grid using 3M-PLL contro...
This study proposes a single-stage solar photovoltaic energy conversion system (PV-ECS) integrated to a three phase four-wire (3P4W) distribution grid with dual-function capabilities, i.e. active power transfer and power quality (PQ) enhancement at the point of interaction (PoI). The PV-ECS system comprises of a solar photovoltaic array and a voltage source inverter (VSI), supplying active power (during daytime) to the distribution grid and connected single-phase and three-phase loads. Apart from transfer of power, the system also improves the PQ at the PoI by compensating reactive power and neutral current, attenuating harmonics, correcting power factor and balancing grid currents. During night, the VSI acts as a shunt active power filter mitigating PQ issues, thereby increasing the device utilisation factor. A three-phase magnitude-phase locked loop (3M-PLL) method is utilised to extract and estimate fundamental term of load currents and an incremental conductance algorithm is applied for maximum power point tracking. To demonstrate its effectiveness, the system is modelled and its performance is simulated on MATLAB and experiments are performed on a developed prototype in the laboratory.
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System
In the past few years the growing demand for electricity and serious concern
for the environment have given rise to the growth of sustainable sources like
wind, solar, tidal, biomass etc. The technological advancement in power
electronics has led to the extensive usage of solar power. Solar power output
varies with the weather conditions and under shading conditions. With the
increasing concerns of the impacts of the high penetration of Photovoltaic
(PV) systems, a technical study about their effects on the power quality of
the utility grid is required. This paper investigates the functioning of a gridtied
PV system along with maximum power point tracking (MPPT)
algorithm. The effects of varying atmospheric conditions like solar irradiance
and temperature are also taken into account. It is proposed in this work that
an Electric Vehicle (EV) can be used as an energy storage to stabilize the
power supplied to the grid from the photovoltaic resources. A coordinated
control is necessary for the EV to obtain desired outcome. The modeling of
the PV and EV system is carried out in PSCAD and the proposed idea is
verified through simulation results utilizing real field data for solar irradiance
and temperature.
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
Transformerless grid-connected inverters have been extensively popular in renewable energy-based applications owing to some interesting features like higher efficiency, reasonable cost and acceptable power density. The major concern of such converters is the leakage current problem and also the step-down feature of the output voltage which causes a costly operation for a single stage energy conversion system. A new five-level transformerless inverter topology is presented in this study, which is able to boost the value of the input voltage and can remove the leakage current problem through a common-grounded architecture. Here, providing the five-level of the output voltage with only six power switches is facilitated through the series-parallel switching of a switched-capacitor module. Regarding this switching conversion, the self- voltage balancing of the integrated capacitors over a full cycle of the grid’s frequency can be acquired. Additionally, to inject a tightly controlled current to the local grid, a peak current controller-based technique is employed, which can regulate both the active and reactive power support modes. Theoretical analyses besides some experimental results are also given to corroborate the correct performance of the proposed topology.
Single phase grid connected photovoltaic inverter
This article proposes a topology for single-phase two stage grid connected solar photovoltaic (PV) inverter for residential applications. Our proposed grid-connected power converter consists of a switch mode DC-DC boost converter and a H-bridge inverter. The switching strategy of proposed inverter consists with a combination of sinusoidal pulse width modulation (SPWM) and square wave along with grid synchronization condition. The performance of the proposed inverter is simulated under grid-connected scenario via PSIM. Furthermore, the intelligent PV module system is implemented using a simple maximum power point tracking (MPPT) method utilizing power balance is also employed in order to increase the systems efficiency.
Similar to Stability enhancement of wind power system by using energy capacitor system (20)
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
Novel High Performance Stand Alone Solar PV System with High Gain, High Effic...
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
Permanent Magnet Synchronous Generator-Based Standalone Wind Energy Supply Sy...
Simulation and analysis of perturb and observe mppt algorithm for array using...
Simulation and analysis of perturb and observe mppt algorithm for array using...
Single-phase solar PV system with battery and exchange of power in grid-conne...
Single-phase solar PV system with battery and exchange of power in grid-conne...
A Management of power flow for DC Microgrid with Solar and Wind Energy Sources
A Management of power flow for DC Microgrid with Solar and Wind Energy Sources
A HYBRID AC/DC SOLAR POWERED STANDALONE SYSTEM WITHOUT INVERTER BASED ON LOAD...
A HYBRID AC/DC SOLAR POWERED STANDALONE SYSTEM WITHOUT INVERTER BASED ON LOAD...
An advanced multilevel converter topology with Reduced switching elements
An advanced multilevel converter topology with Reduced switching elements
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
A three phase grid tied spv system with adaptive dc link voltage for cpi volt...
A 5-level High Efficiency Low Cost Hybrid Neutral Point Clamped Transformerle...
A 5-level High Efficiency Low Cost Hybrid Neutral Point Clamped Transformerle...
Statcom for improved dynamic performance of wind farms in power grid
Statcom for improved dynamic performance of wind farms in power grid
Modeling, Control, and Performance Evaluation of Grid-Tied Hybrid PV/Wind Pow...
Modeling, Control, and Performance Evaluation of Grid-Tied Hybrid PV/Wind Pow...
Maximum power extraction from wind energy system based on fuzzy logic control
Maximum power extraction from wind energy system based on fuzzy logic control
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
Design and Control of Wind integrated Shunt Active Power Filter to Improve Po...
Modeling, Control, and Performance Evaluation of Grid-Tied Hybrid PV/Wind Pow...
Modeling, Control, and Performance Evaluation of Grid-Tied Hybrid PV/Wind Pow...
Control of a Three-Phase Hybrid Converter for a PV Charging Station
Control of a Three-Phase Hybrid Converter for a PV Charging Station
Dual-function PV-ECS integrated to 3P4W distribution grid using 3M-PLL contro...
Dual-function PV-ECS integrated to 3P4W distribution grid using 3M-PLL contro...
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System
Electric Vehicle as an Energy Storage for Grid Connected Solar Power System
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
A New Switched-Capacitor Five-Level Inverter Suitable for Transformerless Gri...
More from Asoka Technologies
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
In this paper; a variable dc link based novel multilevel inverter (MLI) topology is proposed. This proposed topology comprises two variable dc links and a modified H-bridge unit. This new single-phase topology offers advantages such as reduction in count of switches; gate drivers and dc sources while simultaneously improving the power quality. The proposed topology has been analyzed for both symmetric and asymmetric modes of operation. A comparative study of the proposed topology with some recent MLI topologies has been presented. The comparative study indicates that the proposed topology requires less number of dc sources; switches and driver circuits as compared to other topologies. The proposed topology has been simulated for 31- level asymmetric configuration in MATLAB/SIMULINK environment to verify the proper operation of proposed topology. Harmonic analysis was also performed for 31-level inverter which showed significant reduction in the total harmonic distortion (THD) for phase voltage and current waveforms. The proposed topology is suitable for low voltage applications such as standalone photovoltaic (PV) systems and hybrid electric vehicles (HEVs).
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A simplified space vector pulse-width modulation (SVPWM) for three-phase cascaded H-bridge (CHB) inverters is presented in this paper. Treating each unit as a three-level inverter and adopting serial calculation mode, a CHB inverter is modulated unit by unit using three-level SVPWM. Duty cycles of real sector are obtained by mapping duty cycles of sector 1, in which the calculation of three-level SVPWM is done. The process to implement multilevel SVPWM is simplified to the process to implement three-level SVPWM. By reusing FPGA chip resource which is used for the calculation of three-level SVPWM, the presented SVPWM can be easily adopted to a CHB inverter with different number of units, while the FPGA chip resource utilization is reduced significantly. In addition, the presented SVPWM provides an effective switching frequency higher than the switching frequency of IGBTs. Simulation and experimental results are provided to verify the feasibility of the presented SVPWM.
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
In the low voltage based renewable systems like PV and Fuel cell applications, the step-up of the output voltage to drive the loads is essential. For this, the integration of switched-capacitor (SC) units with the dc-ac converters will have the potential advantages like improved efficiency, optimal switching devices, small size of passive elements (L and C) as compared with traditional two-stage conversion system (dc/dc converter and dc/ac converter). This paper focuses on a new family of step-up multilevel inverter topologies with switched capacitor integration with dual input voltage sources. With the flexibility of 2 dc sources and switching capacitor circuits, four different topologies have been suggested in this paper with features of high voltage gain, reduced component count, reduced voltage stress and self-voltage balancing of the capacitor while achieving a higher number of levels. A detailed analysis of proposed multilevel inverters has been analyzed with the symmetrical and asymmetrical mode of operations and the associated gain, the number of levels, and other performance indices are presented. An in-depth study of all the topologies has been accomplished in this paper with several comparative studies in terms of components count, voltage gain and cost. The effectiveness and practicability of the suggested topology with 13 level output voltage has been explained by the experimental results obtained from a scale down prototype.
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi-cell hybrid 21-Level multilevel inverter is proposed in this paper. The proposed topology includes two-unit; an H-bridge is cascaded with a modified K-type unit to generate an output voltage waveform with 21 levels based only on two unequal DC suppliers. The proposed topology's advantage lies in the fine and clear output voltage waveforms with high output efficiency. Meanwhile, the high number of output voltage waveform levels generates a low level of distortion and reduces the level of an electromagnetic interface (EMI). Moreover, it reduces the voltage stress on the switching devices and gives it a long lifetime. Also, the reduction in the number of components has a noticeable role in saving size and cost. Regarding the capacitors charging, the proposed topology presents an online method for charging and balancing the capacitor's voltage without any auxiliary circuits. The proposed topology can upgrade to a high number of output steps through the cascading connection. Undoubtedly this cascading will increase the power level to medium and high levels and reduce the harmonics content to a neglectable rate. The proposed system has been tested through the simulation results, and an experimental prototype based on the controller dSPACE (DS-1103) hardware unit used to support the simulation results.
A generalized multilevel inverter topology with reduction of total standing v...
This paper presents a new multilevel inverter topology with reduced active switches and total standing voltage. The proposed topology can generate a high number of voltage levels in the symmetric configuration. This topology intuitively generates positive and negative cycles without an additional H-bridge unit, which considerably reduces the total standing voltage of the inverter. A cascaded structure is developed from the proposed topology to create higher voltage levels. To show the novelty of the proposed topology, a thorough comparison between the available and the proposed topologies in terms of the number of switches, standing voltages, and dc-sources is presented. Furthermore, the power loss analysis is carried out for various load values. The feasibility of the proposed nine-level inverter is verified with simulation and experimental results.
Residential Community Load Management based on Optimal Design of Standalone H...
Microgrids being an important entity in the distribution system, and to get their full advantages
by incorporating maximum distributed generation, standalone hybrid renewable energy systems (HRESs), being environmentally-safe and economically-efficient, are considered as the promising solution to electrify remote areas where the grid power is not available. In this work, a techno-economic investigation with an optimal design of HRES is presented to fulfill the domestic electricity need for a residential area of the Sherani district in the Province of Baluchistan, Pakistan. Nine case studies based on PV/wind/diesel/battery are analyzed based on net present cost (NPC), cost of energy (COE), and emission to decide the feasible solution. HOMER tool is utilized to accomplish modeling and simulation for economic analysis and optimal sizing. Simulation results demonstrated that HRES with PV-wind-battery is the most viable option for the specified area, and the optimal sizing of components are also obtained with $ 28,620 NPC and 0.311 $/kWh COE which shows 81.65% reduction in cost and 100% preserving in toxic emission while fulfilling 100% energy demand with 67.3% of excess energy. Furthermore, MATLAB/Simulink modeling for the optimally designed system is built for technical analysis while its effectiveness is proved by keeping dc and ac buses voltage constant, safe operating range of battery state of charge (SOC) with active power balance between HRES components, as well as efficient ac voltage quality, regardless of generation disturbances and load fluctuations. The output signal has total harmonic distortion (THD) of 0.30% as compared to 5.44% with the conventional control scheme. The novelty lies in the sequential application of both HOMER and MATLAB simulations of the proposed HRES model and validation of the proposition for the studied area; by using and implementing model predictive control (MPC) of a reconfigurable inverter.
Reliability evaluation of MPPT based interleaved boost converter for PV system
The demand for power supply and depletion of the conventional energy sources are increasing drastically. So to overcome this problem, the best alternative power generation for conventional fossil fuel is Photovoltaic solar cell based system because of its advantage of pollution free and its availability in abundance with free of cost. In the MPPT based PV system the converters are the most sensitive part. Therefore to provide uninterrupted power supply without compromising the quality of power, reliability evaluation of interleaved boost converter becomes necessary. MATLAB/Simulink is used for the simulation studies and to determine the power losses of various components of the converter which is used in calculating the failure rates and reliability of the interleaved boost converter. Reliability studies of IBC have not been studied much. However there exists few literature in which reliability expression has been developed using Markov technique which is a more complex method as compare to Reliability Block Diagram (RBD). Therefore this paper proposes reliability modeling and reliability evaluation of Interleaved boost converter in MPPT based photo-voltaic system by using simple RBD method.
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Voltage-source inverter has been used widely in traditional photovoltaic systems which have limitations. To overcome, Z-source inverter has been introduced. In spite of all the features introduced in Z-source inverter, its configuration has been improved over the years, like trans-Z-source inverter which has added advantages compared to traditional inverters, namely buck–boost feature, lesser passive elements, and higher voltage boost gain. In this paper, photovoltaic arrays are connected to the grid via the trans-Z-source inverter with the aim of improving its power quality. Moreover, the shoot through duty ratio is kept constant in the switching control method to add features like lower voltage stress (higher reliability), lower total harmonic distortion (lower maintenance cost), and higher voltage boost ratio. To evaluate the precision of the proposed system, the photovoltaic system is simulated on a standard grid and under partial shading condition which brings about voltage sag, and hence, a dynamic voltage restorer is used to mitigate voltage sag. Simulation results are presented to verify the validation of the proposed photovoltaic system in terms of voltage and current THD reducing 78.2% and 19.7%, respectively.
Power optimisation scheme of induction motor using FLC for electric vehicle
In electric vehicles (EVs) and hybrid EVs, energy efficiency is essential where the energy storage is limited. Adding to its high stability and low cost, the induction motor efficiency improves with loss minimisation. Also, it can consume more power than the actual need to perform its working when it is operating in less than full load condition. This study proposes a control strategy based on the fuzzy logic control (FLC) for EV applications. FLC controller can improve the starting current amplitude and saves more power. Through the MATLAB/SIMULINK software package, the performance of this control was verified through simulation. As compared with the conventional proportional integral derivative controller, the simulation schemes show good, high-performance results in time-domain response and rapid rejection of system-affected disturbance. Therefore, the core losses of the induction motor are greatly reduced, and in this way improves the efficiency of the driving system. Finally, the suggested control system is validated by the experimental results obtained in the authors’ laboratory, which are in good agreement with the simulation results.
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
This paper introduces a new approach for power flow control of interconnected AC-DC microgrids in grid-connected hybrid microgrids based on implementing a modified unified interphase power controller (UIPC). A typical grid-connected hybrid microgrid including one AC microgrid and one DC microgrid is considered as studied system. Instead of using the parallel-connected power converters, these microgrids are interconnected using a modified UIPC. As the first contribution of this paper, the conventional structure of UIPC, which uses three power converters in each phase, is modified so that a reduced number of power converters is implemented for power exchange control between AC-DC microgrids. The modified structure includes one power converter in each phase, named as line power converter (LPC), and a power converter which regulates the DC bus voltage, named as bus power converter (BPC) here. The AC microgrid is connected to the main grid through the LPCs which their DC buses are linked and can operate in capacitance mode (CM) or inductance mode (IM). A fuzzy logic controller is used in the control structure of the LPCs. The fuzzy inference system is optimized based on H∞ filtering method to reduce the errors in membership functions design. Through the BPC, the DC voltage of LPCs is supplied by the DC microgrid. However, since the DC microgrid voltage is provided here by a PV system, the DC link voltage of the LPCs is fluctuating. Thus, as the second contribution, to stabilize the DC link fluctuations, a new nonlinear disturbance observer based robust multiple-surface sliding mode control (NDO-MS-SMC) strategy is presented for DC side control of the BPC. The simulation results confirm the effectiveness of the proposed power flow control strategy of the improved UIPC for hybrid microgrids.
Multifunctional grid tied pv system using modified klms control
This paper deals with the modified kernel least mean square (KLMS) control strategy in double-stage, solar photovoltaic (PV) grid tied system to enhance the power quality at common coupling point (CCP). This proposed control algorithm has less oscillations, fast convergence, fast dynamic response and good steady state performance. A control strategy is used to extract the fundamental active current component of load and generates reference grid current for a DC-AC converter. The proposed modified KLMS control mitigates multiple power quality concerns such as harmonics reduction, unity power factor and load balancing. The dynamic performance of proposed system is confirmed into the MATLAB\Simulink environment. Test results on hardware implementation are presented at varying solar irradiation levels and load unbalancing. Test results are found satisfactory and total harmonic distortion (THD) of the grid currents are observed well within the IEEE-519 standard.
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
The strive for efficient and cost-effective photovoltaic systems motivated the power electronic design developed here. The work resulted in a DC-DC converter for module integration and distributed maximum power point tracking (MPPT) with a novel adaptive control scheme. The latter is essential for the combined features of high energy efficiency and high power quality over a wide range of operating conditions. The switching frequency is optimally modulated as a function of solar irradiance for power conversion efficiency maximization. With the rise of irradiance, the frequency is reduced to reach the conversion efficiency target. A search algorithm is developed to determine the optimal switching frequency step. Reducing the switching frequency may, however, compromise MPPT efficiency. Furthermore, it leads to increased ripple content. Therefore, to achieve a uniform high power quality at all conditions, interleaved converter cells are adaptively activated. The overall cost is kept low by selecting components that allow for implementing the functions at low cost. Simulation results show the high value of the module integrated converter for DC standalone and microgrid applications. A 400 W prototype was implemented at 0.14 Euro/W. Testing showed efficiencies above 95% taking into account all losses from power conversion, MPPT, and measurement and control circuitry.
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Linear droop control can realize power sharing among generators in DC microgrid without relying on critical communication links. However, the droop relationship between output power and voltage magnitude of renewable power generate system is nonlinear with uncertainties and disturbances from renewable sources and loads in practical DC microgrid. A novel droop scheme is proposed for an isolated DC microgrid to solve the nonlinear problem. The control strategy is proposed by using the Takagi-Sugeno (T-S) fuzzy model and sliding mode algorithm. The nonlinear droop characteristics can be represented by T-S model through taking advantage of locally measured output variables. The sliding mode droop controller is designed for compensating the uncertainties and disturbances to derive accurate power sharing based on T-S fuzzy model. The proposed scheme is proved to be effective under variable operating conditions through PSIM/Matlab simulation.
Implementation of solar pv battery and diesel generator based electric vehic...
In this paper, a solar PV (Photovoltaic) array, a battery energy storage (BES), a diesel generator (DG) set and grid based EV charging station (CS) is utilized to provide the incessant charging in islanded, grid connected and DG set connected modes. The charging station is primarily designed to use the solar photovoltaic PV array and a BES to charge the electric vehicle (EV) battery. However, in case of exhausted storage battery and unavailable solar PV array generation, the charging station intelligently takes power from the grid or DG (Diesel Generator) set. However, the power from DG set is drawn in a manner that, it always operates at 80-85% loading to achieve maximum fuel efficiency under all loading conditions. Moreover, in coordination with the storage battery, the charging station regulates the generator voltage and frequency without a mechanical speed governor. It also ensures that the power drawn from the grid or the DG set is at unity power factor (UPF) even at nonlinear loading. Moreover, the PCC (Point of Common Coupling) voltage is synchronized to the grid/ generator voltage to obtain the ceaseless charging. The charging station also performs the vehicle to grid active/reactive power transfer, vehicle to home and vehicle to vehicle power transfer for increasing the operational efficiency of the charging station. The operation of the charging station is experimentally validated using the prototype developed in the laboratory.
High step up quasi-z source dc-dc converter
In this paper, a high step-up Quasi-Z Source (QZS) DC-DC converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS DC-DC converter while keeping its main advantages such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch isn’t increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based DC-DC converters is provided which confirms the superiority of the proposed converter. Simulations are done in PSCAD/EMTDC in order to investigate the MPPT capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype.
Fuel cell integrated unified power quality conditioner for voltage and curren...
Electrical and electronic devices when exposed to one or more power quality problems are prone to failure. This paper aims to enhance the quality of power in three-phase four-wire distribution grid using Fuel Cell Integrated Unified Power Quality Conditioner (FCI-UPQC). The proposed FCI-UPQC has four-leg converter on the shunt side and three-leg converter on the series side. A combination of a synchronous reference frame (SRF) and Instantaneous Reactive Power (IRP) theories are utilized to generate reference signals of the FCI-UPQC. Also, this paper proposes Adaptive Neuro-Fuzzy Inference System controller to maintain DC link voltage in the FCI-UPQC. The Adaptive Neuro-Fuzzy Inference System controller is designed like a sugeno fuzzy architecture and trained offline using data from the Proportional Integral (PI) controller. The obtained results proved that the proposed FCI-UPQC compensated power quality problems such as voltage sag, swell, harmonics, neutral current, source current imbalance in three-phase four-wire distribution grid. The presence of fuel cell in this work makes more effectiveness of the proposed system by providing real power support during supply interruption on the grid side.
Distributed incremental adaptive filter controlled grid interactive residenti...
In this paper, a distributed incremental adaptive filter (DIAF) controlled utility interfaced photovoltaic (PV) - battery microgrid system is presented with power quality features. From protection aspects, grid tied solar inverters are required to shut down at loss of the utility. However, the multi-purpose PV-battery system is developed to provide energy to the critical loads, even at loss of distribution network. The bidirectional controlled converter with a battery also mitigates the intermittency of a PV array under rapid variations in the weather. The extracted maximum power is supplied to the voltage source converter (VSC), which is transferred to the nonlinear loads and the utility. The distributed incremental adaptive filter is used to control the VSC with contribution of PV power and the battery. In addition, the DIAF control provides harmonics mitigation, load balancing and power factor improvement functionalities in order to deal with system connected with nonlinear loads. A PV power feed-forward (PVFF) term is incorporated in the current control for injection of active power to the utility as well as to improve the dynamic operation of residential PV-battery microgrid. The battery energy storage (BES) reduces the fuel bills and it is also utilized to provide smoothing attributes to the microgrid. The effectiveness of PV-battery microgrid is validated experimentally developed in the laboratory.
Application of Artificial Neural Networks for Shunt APF Control
Artificial Neural Network (ANN) is becoming an attractive estimation and regression technique in many control applications due to its parallel computing nature and high learning capability. There has been a lot of effort in employing the ANN in shunt active power filter (APF) control applications. Adaptive Linear Neuron (ADALINE) and feed-forward Multilayer Neural Network (MNN) are the most commonly used ANN techniques to extract fundamental and/or harmonic components present in the non-linear currents. This paper aims to provide an in-depth understanding on realizing ADALINE and feed-forward MNN based control algorithms for shunt APF. A step-by-step procedure to implement these ANN based techniques, in Matlab/ Simulink environment, is provided. Furthermore, a detailed analysis on the performance, limitation and advantages of both methods is presented in the paper. The study is supported by conducting both simulation and experimental validations.
Control strategy of pmsg based wind energy conversion system under strong win...
This paper presents a control approach for the Permanent Magnet Synchronous Generator (PMSG) based Wind Energy Conversion Systems (WECS) under a wide range of wind speeds. Generally, most of the wind turbines are turned-off and disconnected from the power grid, in case wind velocity is gone over 25 m/s. It may cause wind power supply shortage from wind farms. This research introduces a pitch angle controller as well as a rotational speed control system so that the PMSG based WECS can generate power if the wind speeds are above 25 m/s. The proposed method reduces the mechanical stress of the wind turbine by preferential reducing of the rotational speed rather than the mechanical torque during strong wind condition. As a result, the chance of turning-off the is reduced compared to the conventional control system because the PMSG based WECS can temporarily tolerate the wind speed up to 35 m/s. A 2 MW WECS with the electrical and mechanical characteristics is modeled in the MATLAB/Sim Power Systems® to verify the proposed research.
Control and energy management of a large scale grid connected pv system
Power quality is highlighted as an important parameter in modern power systems. Moreover, grid-connected photovoltaic power plants are increasing significantly in size and capacity. Elsewhere, due to the progressive integration of nonlinear loads in the grid, the principal role of a Solar Energy Conversion System (SECS) is not only to capture the maximum power from solar but, also to ensure some ancillary services and improve the quality of power. This paper presents a novel strategy dedicated to improve the management of active power generation, reactive power compensation and power quality of a SECS, while guaranteeing the possibility of exploiting the full capacity of the Power Conditioning System (PCS) and the PhotoVoltaic System (PVS). The proposed control algorithm is applied to a large scale PVS connected to the grid through a cascade of a DC-DC converter and a PWM inverter. This control strategy manages the SECS function’s priorities, between main active power generation, reactive power compensation and active filtering in such a way to guarantee a smooth and stable DC voltage and ensure a sinusoidal grid current. Top priority is given to the active power production over power quality improvement. Then, priority is given to reactive power compensation over mitigation of current harmonics absorbed by the non-linear load connected to the Point of Common Coupling (PCC). Moreover, the whole system upper limits of active and reactive powers have been determined in the (PQ) power plane on the basis of PVS available power, converters rated power and DC bus voltage smoothness and stability. Finally, a control procedure dedicated to the calculation of the inverter current commands is proposed in order to exploit the full capacity of the SECS and respect the determined power limits. Simulation results confirm the effectiveness and the performance of this control strategy and prove that the SECS can operate at its full power whilst the power quality can be improved by reactive power compensation and active filtering.
More from Asoka Technologies (20)
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Variable DC Link based Novel Multilevel Inverter Topology for Low Voltage A...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A Simplified Space Vector Pulse-Width Modulation Scheme for Three-Phase Casca...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A New Family of Step-up Hybrid Switched- Capacitor Integrated Multilevel Inve...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A multi cell 21-level hybrid multilevel inverter synthesizes a reduced number...
A generalized multilevel inverter topology with reduction of total standing v...
A generalized multilevel inverter topology with reduction of total standing v...
Residential Community Load Management based on Optimal Design of Standalone H...
Residential Community Load Management based on Optimal Design of Standalone H...
Reliability evaluation of MPPT based interleaved boost converter for PV system
Reliability evaluation of MPPT based interleaved boost converter for PV system
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power Quality Improvement of Grid-Connected Photovoltaic Systems Using Trans-...
Power optimisation scheme of induction motor using FLC for electric vehicle
Power optimisation scheme of induction motor using FLC for electric vehicle
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Power Flow Control of Interconnected AC-DC Microgrids in Grid-Connected Hybri...
Multifunctional grid tied pv system using modified klms control
Multifunctional grid tied pv system using modified klms control
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Irradiance-adaptive PV Module Integrated Converter for High Efficiency and Po...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Intelligent Power Sharing of DC Isolated Microgrid Based on Fuzzy Sliding Mod...
Implementation of solar pv battery and diesel generator based electric vehic...
Implementation of solar pv battery and diesel generator based electric vehic...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Fuel cell integrated unified power quality conditioner for voltage and curren...
Distributed incremental adaptive filter controlled grid interactive residenti...
Distributed incremental adaptive filter controlled grid interactive residenti...
Application of Artificial Neural Networks for Shunt APF Control
Application of Artificial Neural Networks for Shunt APF Control
Control strategy of pmsg based wind energy conversion system under strong win...
Control strategy of pmsg based wind energy conversion system under strong win...
Control and energy management of a large scale grid connected pv system
Control and energy management of a large scale grid connected pv system
Recently uploaded
Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.
Thank me later.
samsarthak31@gmail.com
Hierarchical Digital Twin of a Naval Power System
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
J.Yang, ICLR 2024, MLILAB, KAIST AI.pdf
Language-Interfaced Tabular Oversampling Via Progressive Imputation And Self Autentication
Architectural Portfolio Sean Lockwood
This portfolio contains selected projects I completed during my undergraduate studies. 2018 - 2023
Runway Orientation Based on the Wind Rose Diagram.pptx
Runway Orientation Based on the Wind Rose Diagram
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
HYDROPOWER - Hydroelectric power generation
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
The Benefits and Techniques of Trenchless Pipe Repair.pdf
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Dynamic Programming
Backtracking
Techniques for Graphs
Branch and Bound
WATER CRISIS and its solutions-pptx 1234
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Immunizing Image Classifiers Against Localized Adversary Attacks
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Governing Equations for Fundamental Aerodynamics_Anderson2010.pdf
Governing Equations for Fundamental Aerodynamics
一比一原版(SFU毕业证)西蒙菲莎大学毕业证成绩单如何办理
SFU毕业证原版定制【微信：176555708】【西蒙菲莎大学毕业证成绩单-学位证】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
◆◆◆◆◆ — — — — — — — — 【留学教育】留学归国服务中心 — — — — — -◆◆◆◆◆
【主营项目】
一.毕业证【微信：176555708】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微信：176555708】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
学历顾问：微信：176555708
Recently uploaded (20)
Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf
Top 10 Oil and Gas Projects in Saudi Arabia 2024.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf
Runway Orientation Based on the Wind Rose Diagram.pptx
Runway Orientation Based on the Wind Rose Diagram.pptx
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
The Benefits and Techniques of Trenchless Pipe Repair.pdf
The Benefits and Techniques of Trenchless Pipe Repair.pdf
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Design and Analysis of Algorithms-DP,Backtracking,Graphs,B&B
Immunizing Image Classifiers Against Localized Adversary Attacks
Immunizing Image Classifiers Against Localized Adversary Attacks
block diagram and signal flow graph representation
block diagram and signal flow graph representation
Governing Equations for Fundamental Aerodynamics_Anderson2010.pdf
Governing Equations for Fundamental Aerodynamics_Anderson2010.pdf
Stability enhancement of wind power system by using energy capacitor system
- 1. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Stability Enhancement of Wind Power System by using Energy Capacitor System ABSTRACT: This paper presents Permanent Magnet Synchronous generator (PMSG) based a variable speed wind turbine systems including energy capacitor system (ECS). The ECS is the combination of electric double layer capacitor (EDLC) known as super capacitor and power electronic devices for wind power application with its detailed modeling and control strategy which can supply smooth electrical power to the power grid and makes the system better stable and reliable. As generated power from wind fluctuates randomly, the objective of this control system is to select a line power reference level and to follow the reference level by absorbing or providing active power to or from ECS to smooth output power fluctuation penetrated to the grid and to keep the wind farm terminal voltage at a desired level by supplying necessary reactive power. The performance of the proposed system is investigated by simulation analysis using PSCAD/EMTDC software. KEYWORDS: 1. Variable speed wind generator 2. Permanent Magnet Synchronous generator (PMSG) 3. Energy Capacitor System (ECS) SOFTWARE:MATLAB/SIMULINK
- 2. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 BLOCK DIAGRAM: Fig. 1. Model System
- 3. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 EXPECTED SIMULATION RESULTS: Fig. 2. Response of real wind speed data [case-I] Fig. 3. Response of PMSG generated Active Power [case-I]
- 4. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 4. Grid terminal voltage without & with ECS [case-I] Fig. 5. Grid Power with/without EDLC and EDLC power [case-I]
- 5. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 6. Grid Active Power without and with EDLC [case-I] Fig. 7. EDLC active Power [case-I] Fig. 8. EDLC energy [case-I]
- 6. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 9. Comparison with SMA and ECS Fig. 10. Response of Wind speed [case-II]
- 7. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 11. PMSG generated Active Power [MW] [case-II] Fig. 12. Grid Active Power without and with EDLC [case-II] Fig. 13. EDLC active power [case-II]
- 8. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 Fig. 14. EDLC energy [case-II] Fig. 15. Grid terminal voltage without & with ECS [case-II]. Fig. 16. Frequency deviation of SMA, ECS & without ECS [case-I].
- 9. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 CONCLUSION: The simulation results show that the quality of the terminal voltage and output power penetrated to the grid is not good but continuously varying without ECS system. Besides, when we used ECS system, the terminal voltage and grid power is almost constant and quality of voltage and power is excellent. So, using ECS system smoothed power can be supplied to the grid by charging and discharging of EDLC. By using low pass filter to calculate line power reference instead of SMA, EMA makes the system very simple, compact and cost effective. Therefore, it can be concluded that this proposed system can be applied effectively in power systems to generate high quality electrical power from the natural fluctuating wind. REFERENCES: [1] G. annual report, 2014; world wind energy association. [2] Niu Jiangang, Baotou, “Investigation on the properties of fly ash concrete attacked by a Pseudo-capacitance Faradaic electrochemical storage with electron charge-transfer, achieved by redox reactions, intercalation or electrosorption. Rain,” IEEE, Conference, ICETCE, Lushan, DOI. 10, pp. 2335 – 2339, 22-24 April 2011. [3] Harden F, Bleijis JAM, Jones R, Bromely P, Ruddell AJ, “Application of power-controlled flywheel drive for wind power conditioning in a wind /diesel power system,” Ninth international conference on Electrical Machines and Drives, Canterbury, paper no. 468, pp. 65-70. [4] Senjyu T., Sakamoto R., Urasaki N., Funabashi T. Fujita H., SekineH.,“Output power leveling of wind turbine Generator for all operating regions by pitch angle control,” Energy Conversion, IEEE Transactions, Vol. 21, pp. 467 - 475, 2006.
- 10. ELECTRICAL PROJECTS USING MATLAB/SIMULINK Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 For Simulation Results of the project Contact Us Gmail: asokatechnologies@gmail.com, Website: http://www.asokatechnologies.in 0-9347143789/9949240245 [5] Ali MH, Murata T, Tamura J, “Minimization of fluctuations of line power and terminal voltage of wind generator by fuzzy logiccontrolled SMES,” international review of Electrical engineering, vol. 1, pp. 559-566, 2006.