Pipe and joints by jawad ali
•Download as PPTX, PDF•
11 likes•3,004 views
This document discusses different types of pipe joints used to connect pipes for transporting fluids like water, steam, and gases. It outlines five main types of pipe joints: 1) Union Joints, 2) Nipple Joint, 3) Expansion Joint, 4) Spigot And Socket Joints, and 5) Flange Joint. The pipe joints allow pipes to be connected together to extend their length and overcome limitations on pipe size.
Report
Share
Report
Share
Recommended
Pipe fittings 1429085774768
Pipe fittings are used to connect pipes and allow changes in direction and diameter. Common fittings include elbows, tees, couplings, reducers, bushings, and unions. Materials used for pipes include metal, cement, plastic, cast iron, steel, copper, and PVC. Factors like strength, cost, ease of installation, and health aspects must be considered when selecting pipe materials. Proper pipe selection and installation is important for effective water distribution with minimal contamination and leakage.
PIPES , PIPE FITTINGS,PIPE JOINTS & LAYING OF PIPELINES
installation part of water supply system. in this ppt you will also get the detail about laying of pipe lines into ground. this one is our college report
Types of plumbing and pipe fittings
This document describes and defines various types of plumbing pipe fittings. It discusses adaptors, barbs, couplings, crosses, double tapped bushings, elbows, mechanical sleeves, nipples, plugs and caps, reducers, tees, unions, valves, wyes. Each type of fitting serves a different purpose in plumbing systems, such as connecting pipes of different materials or diameters, changing the direction of water flow, or allowing access for maintenance and repairs.
Silambarasan
Pipe fittings come in various shapes and types to allow pipes to change direction or diameter. Common fittings include elbows, tees, couplings, reducers, bushings, and caps. Elbows are used to change the direction of pipes and come in 90 and 45 degree angles. Tee fittings allow branch lines. Valves such as gate valves, check valves, and globe valves are used to control fluid flow. PVC, copper, and other pipe materials each have their own fitting types that are suited to joining those materials.
Laying, jointing and testing of pipes
This document discusses various types of pipe joints used in water supply systems. It describes bell and spigot joints, expansion joints, flanged joints, mechanical joints, flexible joints, screwed joints, collar joints, and A.C. pipe joints. For each type of joint it provides details on the purpose, construction, and materials used. The document also covers topics like pipe laying works, testing of pipe lines, hydraulic design of pipe networks, and appurtenances in pipe lines.
Pipes, fittings-fixtures and appliance
types of pipes and its installation methods and fittings associated with it (with explanatory figure), fixtures and hot water appliance.
Pipes and pipe joints
The document discusses the design of pipes and pipe joints. It covers topics such as stresses in pipes, wall thickness calculations, types of pipe joints like flanged joints, and design considerations for circular, oval and square flanged pipe joints. Design examples are provided for calculating stresses in pipes, pipe dimensions, and dimensions of different flanged pipe joints based on internal fluid pressure and material properties. Standard dimensions for steam pipe flanges according to Indian boiler regulations are also mentioned. Hydraulic pipe joints for high pressures use heavier oval or square flanges secured by multiple bolts to withstand pressures up to 47.5 N/mm2.
pipes fittings &valves
Seamless pipe is formed by piercing a solid steel rod with a mandrel to produce a seamless pipe. Butt-welded pipe is formed by rolling hot steel plate into a hollow shape and fusing the ends together. There are various types of pipes, fittings, and joints used in pipe systems, including elbows, tees, flanges, and valves, which connect pipes and regulate or direct fluid flow. Proper selection of pipe material, size, wall thickness, and fittings depends on the application parameters like pressure, temperature, and fluid properties.
Recommended
Pipe fittings 1429085774768
Pipe fittings are used to connect pipes and allow changes in direction and diameter. Common fittings include elbows, tees, couplings, reducers, bushings, and unions. Materials used for pipes include metal, cement, plastic, cast iron, steel, copper, and PVC. Factors like strength, cost, ease of installation, and health aspects must be considered when selecting pipe materials. Proper pipe selection and installation is important for effective water distribution with minimal contamination and leakage.
PIPES , PIPE FITTINGS,PIPE JOINTS & LAYING OF PIPELINES
installation part of water supply system. in this ppt you will also get the detail about laying of pipe lines into ground. this one is our college report
Types of plumbing and pipe fittings
This document describes and defines various types of plumbing pipe fittings. It discusses adaptors, barbs, couplings, crosses, double tapped bushings, elbows, mechanical sleeves, nipples, plugs and caps, reducers, tees, unions, valves, wyes. Each type of fitting serves a different purpose in plumbing systems, such as connecting pipes of different materials or diameters, changing the direction of water flow, or allowing access for maintenance and repairs.
Silambarasan
Pipe fittings come in various shapes and types to allow pipes to change direction or diameter. Common fittings include elbows, tees, couplings, reducers, bushings, and caps. Elbows are used to change the direction of pipes and come in 90 and 45 degree angles. Tee fittings allow branch lines. Valves such as gate valves, check valves, and globe valves are used to control fluid flow. PVC, copper, and other pipe materials each have their own fitting types that are suited to joining those materials.
Laying, jointing and testing of pipes
This document discusses various types of pipe joints used in water supply systems. It describes bell and spigot joints, expansion joints, flanged joints, mechanical joints, flexible joints, screwed joints, collar joints, and A.C. pipe joints. For each type of joint it provides details on the purpose, construction, and materials used. The document also covers topics like pipe laying works, testing of pipe lines, hydraulic design of pipe networks, and appurtenances in pipe lines.
Pipes, fittings-fixtures and appliance
types of pipes and its installation methods and fittings associated with it (with explanatory figure), fixtures and hot water appliance.
Pipes and pipe joints
The document discusses the design of pipes and pipe joints. It covers topics such as stresses in pipes, wall thickness calculations, types of pipe joints like flanged joints, and design considerations for circular, oval and square flanged pipe joints. Design examples are provided for calculating stresses in pipes, pipe dimensions, and dimensions of different flanged pipe joints based on internal fluid pressure and material properties. Standard dimensions for steam pipe flanges according to Indian boiler regulations are also mentioned. Hydraulic pipe joints for high pressures use heavier oval or square flanges secured by multiple bolts to withstand pressures up to 47.5 N/mm2.
pipes fittings &valves
Seamless pipe is formed by piercing a solid steel rod with a mandrel to produce a seamless pipe. Butt-welded pipe is formed by rolling hot steel plate into a hollow shape and fusing the ends together. There are various types of pipes, fittings, and joints used in pipe systems, including elbows, tees, flanges, and valves, which connect pipes and regulate or direct fluid flow. Proper selection of pipe material, size, wall thickness, and fittings depends on the application parameters like pressure, temperature, and fluid properties.
Fitting and fixtures
This document provides information on piping, fittings, and fixtures used in water supply systems. It discusses various types of pipes used such as galvanized iron, PVC, steel, copper pipes and their characteristics. It also describes common pipe fittings like elbows, tees, reducers, couplings, unions, plugs and end caps. Valves used to regulate water flow such as gate valves, globe valves, ball valves, butterfly valves and check valves are also outlined. The document provides a comprehensive overview of key components for building water supply systems.
Pipe fittings
This document provides information on common pipe fittings used in piping systems. It describes fittings that change the direction of pipe runs such as elbows, tees, reducers, and crosses. It also discusses couplings, swage nipples, olets, stub-ins, plugs, and caps. Elbows come in 90 degree, 45 degree, long radius, short radius, reducing, and mitered varieties. Tees can be equal or reducing. Reducers allow changes in pipe size. Bends and returns are made by bending pipe. Crosses have three outlets from one inlet. Couplings join two pipes. Swage nipples connect butt welded and socket welded pipes. O
Various types of pressure pipes
This document discusses various types of pressure pipes used in water supply systems. The main types discussed are cast iron pipes, steel pipes, reinforced cement concrete pipes, hume steel pipes, vitrified clay pipes, and asbestos cement pipes. For each type, the document outlines the material properties, sizes available, joining methods, advantages, and disadvantages. Cast iron pipes are described as moderately priced and durable but heavy. Steel pipes are presented as strong but corrosive. Reinforced cement concrete pipes have a long lifespan but are difficult to repair.
Sewer joint
1. The document discusses various types of sewer pipe joints, including bandage joints, spigot and socket joints, collar joints, flush joints, mechanical joints, and filled joints.
2. Spigot and socket joints can be rigid, flexible, or semi-flexible and involve a rubber ring to form a water-tight seal. Collar joints are either rigid or semi-flexible.
3. Flush joints are internal or external and are used when sewer pipes pass below culverts. They form a self-centering joint that is flush on the inside and outside.
4. Mechanical joints use devices like flanged rings and bolts to join metallic sewer pipes.
Chapter 7 conveyance of water
This document discusses different types of pipes used for water conveyance, including their materials, advantages, disadvantages, and suitability. The main pipes discussed are cast iron, wrought iron, steel, galvanized iron, concrete, asbestos cement, plastic, and lead/copper pipes. Plastic pipes are now most commonly used due to being lightweight, corrosion resistant, electrically insulating, and economical. Proper laying of pipes involves preparing maps, locating the alignment, dewatering trenches, joining pipes, testing, and disinfection before use.
Pipe fitting and fixtures
Pipe fittings and fixtures are required to join pipes together, change pipe directions, and connect pipes to other systems. They must be durable, easy to install and repair, and made from standardized components. Common types of pipe fittings include bends, tees, crosses, reducers, elbows, couplings, nipples, and valves. Fixtures include items like showers, pillar cocks, and unions that interface directly with the piping system. Proper selection of pipe fittings and fixtures allows for effective distribution of fluids throughout a piping network.
MEASURING, CUTTING, AND JOINING PIPES
This document provides information on measuring, cutting, and joining different types of pipes used in plumbing. It discusses cast iron pipes, galvanized steel pipes, copper pipes, and plastic pipes. For each type, it outlines the recommended uses, considerations for working with the pipes, procedures for cutting and joining, and includes tables with additional technical specifications.
Pipe materials and types of joints [autosaved]
Types of pipes and types of joints. Different types of pipes used for transporting water from reservoir or treatment plant for water supply in environmental engineering
Pipe water distribution system2
This document discusses different types of pipes and valves used in water supply systems. It describes common pipe materials like cast iron, steel, concrete, plastic and their properties. It also explains different valves - stop valves control water flow, check valves allow one-way flow, air relief valves remove trapped air, drain valves empty lines, and pressure relief valves release excess pressure. Pipes and valves are essential to control and distribute water while minimizing losses.
Tube expansion
This document discusses tube expansion, which is defined as eliminating diameter differences between two pipe ends to be joined with welding. The key steps of the tube expansion process include preparing the tube sheet, properly expanding the tubes using a tube expander, and ensuring the expansion is within limits. Tube expansion creates tension between the tube and tube sheet to form a leak-proof joint and can minimize buckling or bending in the tubes.
Plumbing work in construction
The document discusses different types of pipes used in plumbing construction including PVC, RCC, stainless steel, copper, galvanized, and plastic pipes. It describes the features and uses of each pipe type. The document also covers common pipe joints like couplings, elbows, bends, tees, and nipples. Additionally, it examines valves, tapes, and important plumbing equipment like spanners, wrenches, and cutters.
Pipe fittings ffo microproject
The document discusses various pipe fittings, joints, and valves used in plumbing systems. It describes common pipe fittings like elbows, tees, reducers, and collars that are used to connect pipes or change the pipe direction. Different types of joints are also covered, such as threaded, welded, brazed, soldered, grooved, and flanged joints. Finally, the document outlines various valves including sluice valves, scour valves, air valves, and gate valves that are used to control or stop water flow. Proper selection and installation of fittings, joints, and valves ensures smooth functioning and cost-effectiveness of plumbing systems.
Cast Iron and Galvanized Iron Pipes
This presentation contains basic information about cast iron and galvanized iron pipes, with their sizes, manufacturing method and types available in market.
All the information has been taken and compiled from various sources only for educational purpose
Types of fittings and materials in plumbing
This slide is about types of pipes, fittings and materials in plumbing. I get this source in the internet. especially in https://en.wikipedia.org/wiki/Piping_and_plumbing_fitting,https://theconstructor.org/building/types-of-pipe-fittings-in-plumbing/12541/, https://www.hunker.com/13401338/types-of-fittings
Valve and fittings
This is the presentation file including topics of Valve, Fittings, Public standpost, Break Pressure Tank, and Maintenance of water supply scheme. It is done as assignment and study purpose in Pulchowk Campus, Civil Department(074bceGH). The pictures and resources associated with these slides are taken from internet and from our text book by Prof Dr, Bhagwan Ratna Kansakar. The relevant sources site are listed and we are very thankful for all the pictures and other resources. It is study material and free to use.
We would like to thank our teacher Prof. Shukra Paudel for his encouragement and guidelines. I also like to thank my friends. Thank You. Yogesh SN
Plumbing fittings & fixtures
The document discusses the installation of basic sanitary fittings and fixtures. It begins by defining plumbing fixtures as items connected to a plumbing system that carry water, such as bathtubs, sinks, and toilets. Plumbing fittings are used to join or regulate pipes. Common fittings include elbows, tees, reducers, unions, and traps. The document then provides details on various types of fittings and fixtures, describing materials, uses, and diagrams. It emphasizes the importance of properly installing fixtures according to plumbing drawings and codes to ensure access, backflow prevention, and alignment of fixtures.
Conveyance of-water
This document provides an overview of conveying water through pipelines. It discusses different types of pipe materials like cast iron, ductile iron, steel, concrete, galvanized iron and plastic pipes. The key requirements of good pipe materials are described as structural strength, durability, corrosion resistance, imperviousness, smoothness and cost. Different pipe joining methods like socket and spigot, flanged, screwed and expansion joints are also outlined. Finally, the major steps involved in laying pipes like setting out and trench excavation are briefly mentioned.
Interior services unit 3
PLUMBING - Common hand tools used for plumbing and their description and uses, Joints for various types of pipes, Sanitary fitting standards for public conveniences
Different types of pipes and accessories for water supply, controlling fixtures like valves, taps, etc. Fittings and Choice of materials for piping: cast iron, steel, wrought iron, galvanized lead, copper, cement concrete and asbestos pipes, PVC pipes
Sizes of pipes and taps for house drainage, Testing drainage pipes for leakage - smoke test, water test etc, CI pipes for soil disposal and rain water drainage, Wrought iron, steel and brass pipes.
Rain water disposal drainage pipes spouts, sizes of rainwater pipes
04 plumbing fixtures II
This document discusses various types of plumbing fixtures and pipe fittings used in building services. It describes different types of taps including pillar cocks, self-closing taps, and swan neck taps. It also discusses common pipe fittings like elbows, tees, couplings and unions. Different types of pipe joints are explained such as spigot and socket joints, flanged joints, expansion joints, flexible joints, and collar joints. Special joints for concrete and asbestos cement pipes are also covered.
Training material heat exchangers
Shell and tube heat exchangers are widely used in industrial processes to transfer heat. They can efficiently transfer large amounts of heat while taking up relatively little space. There are two main types - smaller designs under 12 inches in diameter made of welded steel with copper tubing, and larger designs from 10-100 inches made to TEMA standards using steel pipe or plate. Key components include tubes, tube sheets to attach tubes, baffles to direct flow, and inlet/outlet ports in the shell. Tube materials and configurations can vary to suit different applications and pressures.
Types of pipes
The document discusses different types of pipes used for water supply, including their materials, sizes, joining methods, advantages and disadvantages. It covers galvanized iron pipes, PVC/plastic pipes, steel pipes, cast iron pipes, PPR pipes. For each type, the document provides details on installation, fittings available, and joining methods like screwed joints, welded joints, etc. It includes diagrams to illustrate pipe connections and joining.
Different Types of Water Pipes And Their Uses
In this checklist we will show you different types of water pipe and their uses. If you want water pipes in bulk, you can visit our site.
More Related Content
What's hot
Fitting and fixtures
This document provides information on piping, fittings, and fixtures used in water supply systems. It discusses various types of pipes used such as galvanized iron, PVC, steel, copper pipes and their characteristics. It also describes common pipe fittings like elbows, tees, reducers, couplings, unions, plugs and end caps. Valves used to regulate water flow such as gate valves, globe valves, ball valves, butterfly valves and check valves are also outlined. The document provides a comprehensive overview of key components for building water supply systems.
Pipe fittings
This document provides information on common pipe fittings used in piping systems. It describes fittings that change the direction of pipe runs such as elbows, tees, reducers, and crosses. It also discusses couplings, swage nipples, olets, stub-ins, plugs, and caps. Elbows come in 90 degree, 45 degree, long radius, short radius, reducing, and mitered varieties. Tees can be equal or reducing. Reducers allow changes in pipe size. Bends and returns are made by bending pipe. Crosses have three outlets from one inlet. Couplings join two pipes. Swage nipples connect butt welded and socket welded pipes. O
Various types of pressure pipes
This document discusses various types of pressure pipes used in water supply systems. The main types discussed are cast iron pipes, steel pipes, reinforced cement concrete pipes, hume steel pipes, vitrified clay pipes, and asbestos cement pipes. For each type, the document outlines the material properties, sizes available, joining methods, advantages, and disadvantages. Cast iron pipes are described as moderately priced and durable but heavy. Steel pipes are presented as strong but corrosive. Reinforced cement concrete pipes have a long lifespan but are difficult to repair.
Sewer joint
1. The document discusses various types of sewer pipe joints, including bandage joints, spigot and socket joints, collar joints, flush joints, mechanical joints, and filled joints.
2. Spigot and socket joints can be rigid, flexible, or semi-flexible and involve a rubber ring to form a water-tight seal. Collar joints are either rigid or semi-flexible.
3. Flush joints are internal or external and are used when sewer pipes pass below culverts. They form a self-centering joint that is flush on the inside and outside.
4. Mechanical joints use devices like flanged rings and bolts to join metallic sewer pipes.
Chapter 7 conveyance of water
This document discusses different types of pipes used for water conveyance, including their materials, advantages, disadvantages, and suitability. The main pipes discussed are cast iron, wrought iron, steel, galvanized iron, concrete, asbestos cement, plastic, and lead/copper pipes. Plastic pipes are now most commonly used due to being lightweight, corrosion resistant, electrically insulating, and economical. Proper laying of pipes involves preparing maps, locating the alignment, dewatering trenches, joining pipes, testing, and disinfection before use.
Pipe fitting and fixtures
Pipe fittings and fixtures are required to join pipes together, change pipe directions, and connect pipes to other systems. They must be durable, easy to install and repair, and made from standardized components. Common types of pipe fittings include bends, tees, crosses, reducers, elbows, couplings, nipples, and valves. Fixtures include items like showers, pillar cocks, and unions that interface directly with the piping system. Proper selection of pipe fittings and fixtures allows for effective distribution of fluids throughout a piping network.
MEASURING, CUTTING, AND JOINING PIPES
This document provides information on measuring, cutting, and joining different types of pipes used in plumbing. It discusses cast iron pipes, galvanized steel pipes, copper pipes, and plastic pipes. For each type, it outlines the recommended uses, considerations for working with the pipes, procedures for cutting and joining, and includes tables with additional technical specifications.
Pipe materials and types of joints [autosaved]
Types of pipes and types of joints. Different types of pipes used for transporting water from reservoir or treatment plant for water supply in environmental engineering
Pipe water distribution system2
This document discusses different types of pipes and valves used in water supply systems. It describes common pipe materials like cast iron, steel, concrete, plastic and their properties. It also explains different valves - stop valves control water flow, check valves allow one-way flow, air relief valves remove trapped air, drain valves empty lines, and pressure relief valves release excess pressure. Pipes and valves are essential to control and distribute water while minimizing losses.
Tube expansion
This document discusses tube expansion, which is defined as eliminating diameter differences between two pipe ends to be joined with welding. The key steps of the tube expansion process include preparing the tube sheet, properly expanding the tubes using a tube expander, and ensuring the expansion is within limits. Tube expansion creates tension between the tube and tube sheet to form a leak-proof joint and can minimize buckling or bending in the tubes.
Plumbing work in construction
The document discusses different types of pipes used in plumbing construction including PVC, RCC, stainless steel, copper, galvanized, and plastic pipes. It describes the features and uses of each pipe type. The document also covers common pipe joints like couplings, elbows, bends, tees, and nipples. Additionally, it examines valves, tapes, and important plumbing equipment like spanners, wrenches, and cutters.
Pipe fittings ffo microproject
The document discusses various pipe fittings, joints, and valves used in plumbing systems. It describes common pipe fittings like elbows, tees, reducers, and collars that are used to connect pipes or change the pipe direction. Different types of joints are also covered, such as threaded, welded, brazed, soldered, grooved, and flanged joints. Finally, the document outlines various valves including sluice valves, scour valves, air valves, and gate valves that are used to control or stop water flow. Proper selection and installation of fittings, joints, and valves ensures smooth functioning and cost-effectiveness of plumbing systems.
Cast Iron and Galvanized Iron Pipes
This presentation contains basic information about cast iron and galvanized iron pipes, with their sizes, manufacturing method and types available in market.
All the information has been taken and compiled from various sources only for educational purpose
Types of fittings and materials in plumbing
This slide is about types of pipes, fittings and materials in plumbing. I get this source in the internet. especially in https://en.wikipedia.org/wiki/Piping_and_plumbing_fitting,https://theconstructor.org/building/types-of-pipe-fittings-in-plumbing/12541/, https://www.hunker.com/13401338/types-of-fittings
Valve and fittings
This is the presentation file including topics of Valve, Fittings, Public standpost, Break Pressure Tank, and Maintenance of water supply scheme. It is done as assignment and study purpose in Pulchowk Campus, Civil Department(074bceGH). The pictures and resources associated with these slides are taken from internet and from our text book by Prof Dr, Bhagwan Ratna Kansakar. The relevant sources site are listed and we are very thankful for all the pictures and other resources. It is study material and free to use.
We would like to thank our teacher Prof. Shukra Paudel for his encouragement and guidelines. I also like to thank my friends. Thank You. Yogesh SN
Plumbing fittings & fixtures
The document discusses the installation of basic sanitary fittings and fixtures. It begins by defining plumbing fixtures as items connected to a plumbing system that carry water, such as bathtubs, sinks, and toilets. Plumbing fittings are used to join or regulate pipes. Common fittings include elbows, tees, reducers, unions, and traps. The document then provides details on various types of fittings and fixtures, describing materials, uses, and diagrams. It emphasizes the importance of properly installing fixtures according to plumbing drawings and codes to ensure access, backflow prevention, and alignment of fixtures.
Conveyance of-water
This document provides an overview of conveying water through pipelines. It discusses different types of pipe materials like cast iron, ductile iron, steel, concrete, galvanized iron and plastic pipes. The key requirements of good pipe materials are described as structural strength, durability, corrosion resistance, imperviousness, smoothness and cost. Different pipe joining methods like socket and spigot, flanged, screwed and expansion joints are also outlined. Finally, the major steps involved in laying pipes like setting out and trench excavation are briefly mentioned.
Interior services unit 3
PLUMBING - Common hand tools used for plumbing and their description and uses, Joints for various types of pipes, Sanitary fitting standards for public conveniences
Different types of pipes and accessories for water supply, controlling fixtures like valves, taps, etc. Fittings and Choice of materials for piping: cast iron, steel, wrought iron, galvanized lead, copper, cement concrete and asbestos pipes, PVC pipes
Sizes of pipes and taps for house drainage, Testing drainage pipes for leakage - smoke test, water test etc, CI pipes for soil disposal and rain water drainage, Wrought iron, steel and brass pipes.
Rain water disposal drainage pipes spouts, sizes of rainwater pipes
04 plumbing fixtures II
This document discusses various types of plumbing fixtures and pipe fittings used in building services. It describes different types of taps including pillar cocks, self-closing taps, and swan neck taps. It also discusses common pipe fittings like elbows, tees, couplings and unions. Different types of pipe joints are explained such as spigot and socket joints, flanged joints, expansion joints, flexible joints, and collar joints. Special joints for concrete and asbestos cement pipes are also covered.
Training material heat exchangers
Shell and tube heat exchangers are widely used in industrial processes to transfer heat. They can efficiently transfer large amounts of heat while taking up relatively little space. There are two main types - smaller designs under 12 inches in diameter made of welded steel with copper tubing, and larger designs from 10-100 inches made to TEMA standards using steel pipe or plate. Key components include tubes, tube sheets to attach tubes, baffles to direct flow, and inlet/outlet ports in the shell. Tube materials and configurations can vary to suit different applications and pressures.
What's hot (20)
Viewers also liked
Types of pipes
The document discusses different types of pipes used for water supply, including their materials, sizes, joining methods, advantages and disadvantages. It covers galvanized iron pipes, PVC/plastic pipes, steel pipes, cast iron pipes, PPR pipes. For each type, the document provides details on installation, fittings available, and joining methods like screwed joints, welded joints, etc. It includes diagrams to illustrate pipe connections and joining.
Different Types of Water Pipes And Their Uses
In this checklist we will show you different types of water pipe and their uses. If you want water pipes in bulk, you can visit our site.
types of pipes
Water supply pipes come in various materials and sizes to distribute water in buildings, homes, and factories. The document outlines the main types of water supply pipes as metallic (steel, galvanized iron, cast iron), cement (concrete, asbestos), and plastic (polyethylene, PVC). It also mentions how sewerage connects to city sewerage pipes and lists efforts to prevent environmental harm such as tree planting, using eco-friendly materials, solar power, and conserving resources.
P.P.T on water distribution system by Manish Pandey
The document discusses different types of distribution networks and pipes used in water distribution systems. It describes dead end, radial, grid iron and ring networks. PVC, CPVC, PEX and copper pipes are discussed. Distribution reservoirs help maintain water pressure and quality by absorbing demand fluctuations. Elevated and surface reservoirs are used. Joints like end caps, tees, strainers and reducers connect pipes. The purpose of distribution systems is to deliver water to consumers with appropriate quality, quantity and pressure.
Sanitary and water supply
The document discusses water distribution systems and sanitary systems. It describes the main components of water distribution systems including pipes, valves, fittings and motors. It also discusses the components of sanitary systems such as traps, pipes, fittings and different plumbing systems. Plumbing systems discussed include single stack, fully ventilated stack, one pipe and dual pipe systems.
Water distribution system
Layout of distribution networks, methods of water distribution, storage
capacity of ESR, and underground service reservoir.
Pumps and types of pumps in detail
The document discusses different types of pumps used in fluid transport systems. It describes positive displacement pumps which use a fixed volume cavity to trap and transport fluid with each cycle. Dynamic pumps are also discussed, which add momentum to fluid without a fixed volume. Centrifugal pumps are described in detail, with their construction, working principle, performance parameters and efficiency calculations explained. The key aspects covered are the use of impellers to impart energy and velocity to fluid which is then converted to pressure by the volute casing.
Pipe Fittings and Valves for Marine Use
Pipe Fittings and Valves for Marine Use by Mohd. Hanif Dewan, Senior Engg. Lecturer, International Maritime Academy, Bangladesh
plumbing
This document provides an overview of plumbing components and materials. It discusses different types of pipes like PEX, copper, PVC, galvanized, and brass. It also describes common pipe fittings such as couplings, reducers, elbows, unions, tees, crosses, caps, and barbs. Finally, it summarizes various valves like ball valves, gate valves, butterfly valves, diaphragm valves, globe valves, check valves, pressure balanced valves, and zone valves.
Water supply system
Only 3% of the world's water is fresh water, which is found as surface water, in rivers underground, frozen in glaciers and ice caps, or as groundwater. The water cycle ensures the continuous movement of water on, above, and below the surface of the Earth. Globally, an estimated 69% of fresh water is used for agriculture, 22% for industry, 8% for domestic purposes, and a very small percentage for recreation. Water is treated and stored before being distributed to homes and buildings through a network of pipes and storage systems.
Piping Training course-How to be an Expert in Pipe & Fittings for Oil & Gas c...
Course Description
Piping a must know skill to work in Oil & Gas and similar Process Industries.
Oil and Gas industry is become a very competitive in the current time. Getting right mentor and right exposer within industry is difficult. With limited training budget spent by company on employee training, it is difficult to acquire the knowledge to success.
Knowing cross-functional skill give you an edge over others in your career success.
This course design based on years of field experience to ensure student will comprehend technical details easily and enjoy overall journey.
Learn in detail every aspect of Pipe & Pipe Fittings used in process industry
•Different types of Pipe, Pipe fittings (Elbow, Tee, reducers, Caps etc.), Flanges, Gaskets, Branch Connection, Bolting materials
•Materials (Metal-Carbon Steel, Stainless Steel, Alloy Steel etc. Non-Metal- PVC/VCM, HDPE, GRE-GRP etc.)
•Manufacturing methods
•Heat treatment requirements
•Inspection and Testing requirements (Non Destructive Testing, Mechanical & Chemical testing)
•Dimensions & Markings requirements
•Code & Standard used in piping
Content and Overview
With 2 hours of content including 30 lectures & 8 Quizzes, this course cover every aspect of Pipe, Pipe fittings, flanges, gaskets, branch connections and bolting material used in Process Piping.
This Course is divided in three parts.
1st part of the course covers fundamental of process industries. In this Part, you will learn about fundamental process piping. You will also learn about Code, Standard & Specification used in process industries.
2nd part cover various types of material used in process industries. In this part, you will learn about Metallic and Non-Metallic material used to manufacture pipe and other piping components.
3rd parts covers in detail about pipe and piping components used in Process piping. In this part we will learn about Industry terminology of Piping components, types of industrial material grade used in manufacturing and entire manufacturing process of these components. You will learn about different manufacturing methods, Heat treatment requirements, Destructive and Non-destructive testing, Visual & Dimensional inspection and Product marking requirements.
Upon completion, you will be able to use this knowledge direct on your Job and you can easily answer any interview question on pipe & fittings.
Valves presentation
The document discusses fundamentals of valves including:
1. Definitions of valves and their basic functions of regulating fluid flow.
2. Common classifications of valves based on their motion types like linear, rotary, and quarter turn.
3. Explanations of common valve types like gate valves, globe valves, ball valves and their basic designs and purposes.
VALVES AND THEIR TYPES
This document provides information on different types of valves used in industrial processes. It defines what a valve is and discusses the importance of valve selection for plant economics and operations. It then classifies and describes common types of valves such as gate valves, ball valves, plug valves, butterfly valves, globe valves, check valves, and diaphragm valves. It also covers valve components, materials of construction, end connections, operators, and control valves. In summary, the document provides a comprehensive overview of valves, their functions, classifications and key design aspects.
pumps and its types-ppt
This document discusses different types of pumps, including their classifications, characteristics, applications, and performance. It describes hydrodynamic/non-positive displacement pumps, which use flow to transfer fluid at relatively low pressure and are generally used for low pressure, high volume applications. It also describes hydrostatic/positive displacement pumps, which have close-fitting components and can create high pressures, making them self-priming. Specific positive displacement pump types like gear, vane, piston and centrifugal pumps are examined in terms of their applications and operating principles. Pump efficiencies including volumetric, mechanical and overall efficiency are also covered.
Presentation plumbing
The document provides an overview of plumbing systems and utilities. It discusses the history and practice of plumbing in the Philippines, components of plumbing systems including water supply and distribution. It also covers water sources, treatment and purification methods, wells and pumps. Storage tanks, valves and controls are also summarized.
Piping ppt1
This document provides an overview of piping systems and components. It discusses that piping is used to convey liquids, gases, or materials through a tubular system. Key piping components include pipes, fittings, flanges, valves, and strainers. Common piping materials include carbon steel, alloy steels, and stainless steels. The document also discusses piping design considerations like material selection, insulation, supports, flexibility analysis, and piping and instrumentation diagrams (P&IDs). Piping stress analysis is conducted to ensure stresses from pressures, temperatures, and other loads do not exceed design limits.
Cold Water Supply Distribution In Building
The document discusses the operating principle of air pressure water distribution systems. It begins by explaining that air is compressible while water is not, allowing air pressure in a tank to reach 15 psi and lift water up to 10.5 meters. It notes the ideal pressure range is 20-40 psi. Automatic controls regulate air compressors to maintain adequate pressure. Advantages include low cost while disadvantages include electricity dependence. The document also examines direct upfeed and triplex pump systems as well as factors affecting water pressure and sizing water pipes.
Pumps and types of pumps
the presentation includes basic ideas about water pumps, various terminology generally used for the pumps, classification of pumps and ideas about the types its construction and working
Marine piping systems
The document discusses various piping systems on ships including bilge, ballast, air/sounding, firefighting, fuel oil, lubricating oil, cooling water, compressed air, domestic water, steam, and cargo systems. Key details provided include requirements for pump capacities, pipe sizing formulas, tank arrangements, safety features such as quick closing valves and alarms, and material considerations for high pressure/temperature applications.
PUMPS
Pumps are devices that use mechanical energy to increase the velocity, pressure, or elevation of liquids and gases. There are two main types of pumps: positive displacement pumps and dynamic pumps. Positive displacement pumps apply direct pressure on a liquid using a reciprocating piston or rotating components. Dynamic pumps use centrifugal force to generate high rotational velocities and convert the kinetic energy of liquids into pressure energy. Common positive displacement pump types include piston pumps, plunger pumps, and diaphragm pumps. Common dynamic pump types include centrifugal pumps which contain an impeller and casing. Proper consideration of factors like net positive suction head are important for pump selection and operation.
Viewers also liked (20)
P.P.T on water distribution system by Manish Pandey
P.P.T on water distribution system by Manish Pandey
Piping Training course-How to be an Expert in Pipe & Fittings for Oil & Gas c...
Piping Training course-How to be an Expert in Pipe & Fittings for Oil & Gas c...
Pipe and joints by jawad ali
- 1. Jawad ali BSMT-01133100 MC-04 Submitted to Engr.Sir Emran
- 2. Introduction: Pipe Joints: The pipe are used for transporting various fluids like a water ,steam ,and other different types of gasses and chemicals from one place to an other with or with out pressure. so there is a on limitations of a pipe size. so the joint are used .so the joints are explain bellow some types:
- 7. 4.Spigot And Socket Joints:
- 9. THE END