Phased array type a block
•
0 likes•56 views
APPLICATION: Phased Array “Type A” Calibration Block is used during the initial setup and calibration of phased array Ultrasonic Unit , This Block can be used to perform task such as beam angle verification , Calibration for Wedge Delay, Sensitivity Calibration, Performing DAC/TCG AND more MATERIAL: ✓ Carbon steel, Stainless Steel, aluminum etc. INCH VERSION DIMENSIONS: ✓ 1.000” thick x 4.000” Hight x 12.00” Long ✓ 4.000” and 2.000” Radii, 19 through holes at 0.040” diameter , 1 through hole at0.080” Diameter , 4FBH at 0.80” diameter x0.080”, 0.160”, 0.235” and 0.315” deep, 4FBH at 0.157” Diameter x0.040”, 0.120”, 0.200” and 0.275” Deep, 3FBH at 0.080” Diameter x 0.120 Deep machined into the 2.000” Radious, 4EDM Notches at .004”, .008”,.012” and .016” deep x 0.20” wide x1.00” Long, METRIC VERSION DIMENSIONS: ✓ 25.0mm thick x 100.0mm Hight x 300.0mm Long ✓ 100.0mm and 50.0mm Radii, 19 through holes at 1.0mm diameter, 1Through hole at 2.0mm diameter , 4FBH AT 2.0mm diameter x2.0mm, 4.0mm, 6.0mm an d8.0mm deep, 4FBH AT 4.0mm diameter x1.0mm, 3.0mm, 5.0mm and 7.0mm deep 3FBH AT 2.0mm diameter x 3.0mmdeep machined into the 50mm radius, 4EDM Notches at 0.1mm, 0.2mm, 0.3mm and 0.4mm deep x 0.5mm wide x25.0mm long
Report
Share
Report
Share
Download to read offline
Recommended
IIW V1 Ultrasonic calibartion block
APPLICATION:
Used for Calibration of Shear and Longitudinal Transducer and Verification of shear wave exit point and refracted angel, Can also be used for resolution and sensitivity checking.
SPECIFICATIONS: ✓ ASTM E164,MIL-STD-2154, IS4904
INCH VERSION DIMENSIONS: ✓ 1.0” x 4.0” x 12.0” With 4” Radious, 2.0” and 0.060” Diameter Hole, 0.240”deep x 0.080” wide slot and 1.0” Radious slot x 0.060” deep x 0.120” wide
METRIC VERSION DIMENSIONS: ✓ 25.0mm x 100mm x 300mm (T x L x H ) With 100mm Radious, 50mm and 1.5mm Diameter Hole, 6.0mm deep x 2.0mm wide slot and 25.0mm Radious slot x 1.5mm deep x 3.0mm wide
MATERIAL: ✓ Carbon steel, Stainless Steel, Aluminum etc.
Primary Adhesive Tester
The PARAM® CZY-G Primary Adhesive Tester uses the rolling ball method to test the instant adhesive properties of specimens by observing the adhesive effect when steel balls contact adhesive tapes. It conforms to Chinese and Japanese standards. The instrument can adjust its angle of inclination to meet test requirements and determines the primary adhesive properties of various adhesives like tapes, patches, and films. It has a testable area width of 80mm and can test steel balls ranging from 1/32 inch to 1 inch in size.
Welding works in steel piping
The presentation talks about various processes, code, equipment used in welding of steel piping in City gas distribution system
Line laser imex_lx55
This document provides information about the LX55 5 Line Laser from IMEX tools. It is a self-leveling laser that projects 4 vertical and 1 horizontal line and has plumb up and down functionality. It can be used for applications like shop fitting, tiling, and construction alignment. Accessories include an optional detector for 50m outdoor use, a tripod, laser pole, glasses, target plate, and hard carry case.
Dealing with meachines
This document discusses drilling machines and their functions and safe operation. It describes different types of drilling machines from handheld power drills to bench-mounted and floor-mounted models. Drilling machines are used to cut holes in materials like metal, wood, and others. The document provides instructions on selecting and using drills properly and safely, including always wearing eye protection, securing the workpiece, and keeping hands clear of drill bits. Safety procedures are emphasized to prevent accidents and loss of time or materials.
Resto hand instrument
This document discusses different methods for sharpening dental instruments, including stationary sharpening stones, mechanical sharpeners, and handpiece stones. It describes the types of stones used like Arkansas, silicon carbide, aluminum oxide, and diamond. Key details are provided on grit sizes, stone shapes, and the basic principles of maintaining proper bevel angles and light pressure while sharpening. Mechanical sharpeners and techniques for specific instruments like chisels and knives are also outlined. The document concludes with sterilization requirements after sharpening instruments.
Destructive test
This document discusses various types of weld inspection and testing methods, including:
- Destructive tests like bend tests, tensile tests, and notch-toughness tests that involve breaking samples to evaluate weld strength and integrity.
- Nondestructive tests like visual inspections, hardness tests, pressure tests, and corrosion tests that examine weld properties without damaging the sample.
- Specific tests are used to qualify welders and procedures or inspect production parts by examining factors like weld strength, microstructure, and corrosion resistance. The results of tests are compared to specifications.
Wedge Style Tensile Grips from Tinius Olsen
Self-tightening wedge grips with spring-loaded wedges to provide the initial gripping and allow rapid loading of the sample. Gripping wedges are supplied with serrated jaw faces for gripping flat samples. Optional V profile wedges are available for gripping round sections.
Web: www.TiniusOlsen.com
Contact Us: info@TiniusOlsen.com
Recommended
IIW V1 Ultrasonic calibartion block
APPLICATION:
Used for Calibration of Shear and Longitudinal Transducer and Verification of shear wave exit point and refracted angel, Can also be used for resolution and sensitivity checking.
SPECIFICATIONS: ✓ ASTM E164,MIL-STD-2154, IS4904
INCH VERSION DIMENSIONS: ✓ 1.0” x 4.0” x 12.0” With 4” Radious, 2.0” and 0.060” Diameter Hole, 0.240”deep x 0.080” wide slot and 1.0” Radious slot x 0.060” deep x 0.120” wide
METRIC VERSION DIMENSIONS: ✓ 25.0mm x 100mm x 300mm (T x L x H ) With 100mm Radious, 50mm and 1.5mm Diameter Hole, 6.0mm deep x 2.0mm wide slot and 25.0mm Radious slot x 1.5mm deep x 3.0mm wide
MATERIAL: ✓ Carbon steel, Stainless Steel, Aluminum etc.
Primary Adhesive Tester
The PARAM® CZY-G Primary Adhesive Tester uses the rolling ball method to test the instant adhesive properties of specimens by observing the adhesive effect when steel balls contact adhesive tapes. It conforms to Chinese and Japanese standards. The instrument can adjust its angle of inclination to meet test requirements and determines the primary adhesive properties of various adhesives like tapes, patches, and films. It has a testable area width of 80mm and can test steel balls ranging from 1/32 inch to 1 inch in size.
Welding works in steel piping
The presentation talks about various processes, code, equipment used in welding of steel piping in City gas distribution system
Line laser imex_lx55
This document provides information about the LX55 5 Line Laser from IMEX tools. It is a self-leveling laser that projects 4 vertical and 1 horizontal line and has plumb up and down functionality. It can be used for applications like shop fitting, tiling, and construction alignment. Accessories include an optional detector for 50m outdoor use, a tripod, laser pole, glasses, target plate, and hard carry case.
Dealing with meachines
This document discusses drilling machines and their functions and safe operation. It describes different types of drilling machines from handheld power drills to bench-mounted and floor-mounted models. Drilling machines are used to cut holes in materials like metal, wood, and others. The document provides instructions on selecting and using drills properly and safely, including always wearing eye protection, securing the workpiece, and keeping hands clear of drill bits. Safety procedures are emphasized to prevent accidents and loss of time or materials.
Resto hand instrument
This document discusses different methods for sharpening dental instruments, including stationary sharpening stones, mechanical sharpeners, and handpiece stones. It describes the types of stones used like Arkansas, silicon carbide, aluminum oxide, and diamond. Key details are provided on grit sizes, stone shapes, and the basic principles of maintaining proper bevel angles and light pressure while sharpening. Mechanical sharpeners and techniques for specific instruments like chisels and knives are also outlined. The document concludes with sterilization requirements after sharpening instruments.
Destructive test
This document discusses various types of weld inspection and testing methods, including:
- Destructive tests like bend tests, tensile tests, and notch-toughness tests that involve breaking samples to evaluate weld strength and integrity.
- Nondestructive tests like visual inspections, hardness tests, pressure tests, and corrosion tests that examine weld properties without damaging the sample.
- Specific tests are used to qualify welders and procedures or inspect production parts by examining factors like weld strength, microstructure, and corrosion resistance. The results of tests are compared to specifications.
Wedge Style Tensile Grips from Tinius Olsen
Self-tightening wedge grips with spring-loaded wedges to provide the initial gripping and allow rapid loading of the sample. Gripping wedges are supplied with serrated jaw faces for gripping flat samples. Optional V profile wedges are available for gripping round sections.
Web: www.TiniusOlsen.com
Contact Us: info@TiniusOlsen.com
DAC Calibration blocks
This document describes ASME non-piping DAC blocks used for angle beam calibration. It provides specifications for carbon steel and stainless steel blocks in various dimensions from 1/2" to 3" thick. The blocks contain three or two side-drilled holes at varying diameters and depths located at 1/4, 1/2, and 3/4 of the thickness. They also contain two EDM notches that are 2% of the thickness deep by 1/4" wide and at least 1" long. Contact information is provided for Kirti NDT & Engineering Services.
Design for in-circuit test (vintage 1994)
This one is an oldie, so please excuse the visual style. It comes from the first year of my PhD studies, 1994. The guidelines shown may still be of use to somebody working in printed circuit board (PCB) design. IT’S PROBABLY BEST DOWNLOADED since it's meant to run as a rolling slideshow, and it achieves a crude form of animations via multiple slides...
File translation courtesy of Zamzar.com, which allowed me to salvage this very old file, and make it available. For the PhD thesis itself (1999), see http://usir.salford.ac.uk/34320/
AWS DSC Calibration Block
This document provides specifications for an AWS DSC BLOCK used to calibrate ultrasonic testing equipment. It describes the block's applications, dimensions for both inch and metric versions, materials it can be made from, and contact information for the manufacturer KIRTI NDT & ENGINEERING SERVICES.
built plans for single 18 inch subwoofer system.pdf
This document provides instructions for constructing an enclosure for the PD-H118A 18" horn-loaded subwoofer. It recommends using at least 18mm thick birch plywood and reinforced joints. Instructions are given for cutting holes, mounting drivers and crossovers, internal bracing, wiring, and acoustic treatment. Three suitable 18" drivers are listed, along with their specifications and mounting configurations. Construction details and a parts list are also included.
Pipe wizard olympus
The document describes PipeWIZARD, an automated ultrasonic inspection system for pipeline girth welds using phased array technology. It can inspect welds fast, in under 4 minutes, and complies with industry codes. Phased arrays allow electronic beam forming for flexible inspection of different pipe diameters and wall thicknesses. The system provides zone discrimination for accurate defect sizing and detection of flaws in welds. It has been used to inspect over 200,000 welds on various pipeline projects worldwide.
Wall Thickness Gauge - (Magna-Mike 8600)
The document introduces the Magna-Mike 8600 thickness gauge. Key features of the 8600 include over 20 new features and improvements compared to previous models, such as two new probe designs, expanded target and thickness measurement ranges, a larger VGA display, and the ability to display live, minimum, maximum and difference readings simultaneously. It also has new calibration kits, programmable instrument lock, and the ability to export data to micro SD cards.
S 3000 radial inserter
This document describes Shenzhen Southern Machinery Sales and Service Co., Ltd and their radial inserter machine, the S-3000. Some key details include:
- The company has developed various component inserters since 2006 and attained a high-tech certification in 2010.
- The S-3000 radial inserter offers high throughput of up to 18,000 components per hour, flexibility to handle various component sizes and spans, and low cost of ownership.
- It allows 360 degree insertion and can handle components like capacitors, transistors, diodes, and connectors for applications in industries like lighting, appliances, vehicles, and more.
Weld probe presentation- Given at COTEQ, Porto Galinhas, Brazil, June 2013
This document discusses the advantages of using eddy current technology and specialized weld probes for weld inspection. It provides background on the development of weld probes and how they work. Weld probes allow inspection of welds through coatings with minimal lift-off sensitivity. They are well-suited for difficult-access inspections and have various applications in industries like offshore, nuclear, and rail. The document also covers standardization, equipment used, and concludes that weld probes provide a good alternative to other NDT methods for weld inspection.
Kurt pmi 10 08
This document summarizes various precision measuring instruments including outside micrometers, dial calipers, test indicators, dial indicators, electronic dial indicators, magnetic bases, and height gages. It provides specifications and features for different models ranging in measurement capacities from 0-1 inches to 0-12 inches and graduation precision from 0.0001 to 0.001 inches.
B m p/ rotary endodontic courses by indian dental academy
Indian Dental Academy: will be one of the most relevant and exciting training center with best faculty and flexible training programs for dental professionals who wish to advance in their dental practice,Offers certified courses in Dental implants,Orthodontics,Endodontics,Cosmetic Dentistry, Prosthetic Dentistry, Periodontics and General Dentistry.
PCB Manufacturer, Domestic Circuit Board Production and Prototype
Saturn Electronics Corporation is a leading printed circuit board fabricator that offers high-volume production and quick-turn prototype boards. It has strong financials with no debt and fully paid buildings and equipment. It owns three fabrication facilities in the US to enhance purchasing power and safeguard production. Saturn serves industries such as aerospace, automotive, defense, medical, and telecommunications with delivery times ranging from one day to three weeks. It has attained several certifications including AS9100, ISO9000, and ISO14001.
New corporate presentation july 2010
Dynamic & Proto Circuits Inc. is a 54,000 square foot facility that produces multilayer printed circuit boards using various solder mask options and new equipment like a HASL machine. The company invests in high speed drilling and via filling equipment to improve efficiency. Technology roadmaps show plans to reduce line widths and increase layer counts by 2012. The facility offers various substrate materials like FR-4 and BT epoxy and surface finishes including ENIG and HASL.
Dr.R.Narayanasamy - Formability of Automobile grade steels
The document discusses a research project analyzing the formability and wrinkling limits of various high strength steel sheets supplied by TATA Steel. Dr. R. Narayanasamy is the principal investigator, studying properties like tensile strength, forming limit diagrams, strain distribution, fractography, and texture. Tests were conducted on interstitial free steel, dual phase steel, and other varieties in thicknesses from 0.6mm to 2.0mm. Charts of chemical composition, microstructure, tensile properties, and forming limit diagrams are presented for each steel type.
Bill Godwin #6 Irrigation Pipe & Fittings Wed Jan 27
This document provides technical specifications for PVC and CPVC Schedule 80 fittings, unions, tank adapters, expansion joints, and saddles. It includes dimensional standards from ASTM for Schedule 80 pipe and socket dimensions as well as American National Standards for taper pipe threads. Recommendations are provided for installers regarding solvent weld connections, threaded connections, and general product use.
Bill Godwin #1 Working with PVC Irrigation Wed jan 27
This document provides technical specifications for PVC and CPVC Schedule 80 fittings, including dimensions according to ASTM standards. It lists nominal pipe sizes from 1/8" to 12" along with minimum wall thicknesses, tolerances, and other dimensional details. The document also provides injection and fabricated fitting dimensions and references, as well as part numbers and weights for PVC and CPVC tee fittings.
Testing/Manufacture/Lab product catalogue
LabproductTM is an ISO 9001 certified company that manufactures world class testing equipment. It has an in-house R&D center for continuous improvement and development of equipment using latest technologies. LabproductTM offers a wide range of automatic and digital testing equipment for industries such as government, defense, and private sectors. It provides complete testing solutions, equipment, training, and consultancy services to customers worldwide.
Phased array type b block
APPLICATION: Used for beam Characterization and evaluation of system performance characteristics. Use it as baseline block to determine long-term instrument performance changes, generate DAC Curves and Evaluate linear/ Angular resolution , Focusing ability and beam steering capabilities. With a variety of targets, this small, lightweight block is also perfect for customer demonstrations of phased array ultrasonic capabilities
Datasheet - Oil And Gas
Fine Tubes’ oil and gas tubing are used in the most challenging subsea and downhole conditions in seawater and sour oil well environments. Materials used are Austenitic, Super Austenitic, Duplex, Super Duplex, Titanium and Nickel Alloys. Seamless tubes are used for hydraulic tube and instrumentation tube applications, in onshore control panels, topside processing facilities, on subsea manifolds and templates up to 2,500m below the sea’s surface. Seam welded & redrawn tubes with orbital joints are used for subsea umbilicals, subsea control lines and chemical injection tubes. We can produce straight tubes or tube coils up to 10,000 m long. Coiled tubing is also used in onshore or topside hydraulic and instrumentation systems where the longer coils result in fewer connections and can increase the integrity of the overall system. These high pressure tubes need to be able to withstand huge amounts of pressure which is why our stainless steel coils for onshore applications are rated for use up to 60,000psi.
Sierra Circuits PCB Fabrication Capabilities
The document discusses Sierra Circuits, a printed circuit board resource company. It introduces Sierra's various business units for prototype and small production volumes, high-density interconnect technology, micro-electronics, offshore manufacturing, and Midwest production. It provides an overview of Sierra's manufacturing capabilities and technologies, including multi-layer boards up to 30 layers, a variety of materials, controlled impedance, blind and buried vias, and various surface finishes. The document encourages readers to stay tuned for more acquisitions, higher technology, and research that will change everything.
Diacutex Diamond Tool Products
This document appears to be a product catalogue for concrete cutting and grinding wheels. It lists various concrete cutting blades with different diameters, segment heights and applications that are suitable for cutting concrete, asphalt, stone and tiles. It also lists grinding cup wheels in various sizes for surface grinding of concrete floors. The blades and wheels can be used with handheld saws, table saws and angle grinders.
Radiography Film Viewer
Features:
High Luminance.
Energy Saving.
Viewing Area: 12”x4”.
Adjustable Shutter for Viewing Area.
Electronic Brightness Control
Specification:
View Film Density up to 5.0 Density.
Input Voltage: 230Volt (±5%).
Power Consumption: 160W approx.
Heavy Aluminum heat sink.
Cooling Fan: 2 Nos.
Plug in Foot Switch.
Foot Switch & foot Switch Cable is shock Proof.
Mini lemo to mini lemo cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
More Related Content
Similar to Phased array type a block
DAC Calibration blocks
This document describes ASME non-piping DAC blocks used for angle beam calibration. It provides specifications for carbon steel and stainless steel blocks in various dimensions from 1/2" to 3" thick. The blocks contain three or two side-drilled holes at varying diameters and depths located at 1/4, 1/2, and 3/4 of the thickness. They also contain two EDM notches that are 2% of the thickness deep by 1/4" wide and at least 1" long. Contact information is provided for Kirti NDT & Engineering Services.
Design for in-circuit test (vintage 1994)
This one is an oldie, so please excuse the visual style. It comes from the first year of my PhD studies, 1994. The guidelines shown may still be of use to somebody working in printed circuit board (PCB) design. IT’S PROBABLY BEST DOWNLOADED since it's meant to run as a rolling slideshow, and it achieves a crude form of animations via multiple slides...
File translation courtesy of Zamzar.com, which allowed me to salvage this very old file, and make it available. For the PhD thesis itself (1999), see http://usir.salford.ac.uk/34320/
AWS DSC Calibration Block
This document provides specifications for an AWS DSC BLOCK used to calibrate ultrasonic testing equipment. It describes the block's applications, dimensions for both inch and metric versions, materials it can be made from, and contact information for the manufacturer KIRTI NDT & ENGINEERING SERVICES.
built plans for single 18 inch subwoofer system.pdf
This document provides instructions for constructing an enclosure for the PD-H118A 18" horn-loaded subwoofer. It recommends using at least 18mm thick birch plywood and reinforced joints. Instructions are given for cutting holes, mounting drivers and crossovers, internal bracing, wiring, and acoustic treatment. Three suitable 18" drivers are listed, along with their specifications and mounting configurations. Construction details and a parts list are also included.
Pipe wizard olympus
The document describes PipeWIZARD, an automated ultrasonic inspection system for pipeline girth welds using phased array technology. It can inspect welds fast, in under 4 minutes, and complies with industry codes. Phased arrays allow electronic beam forming for flexible inspection of different pipe diameters and wall thicknesses. The system provides zone discrimination for accurate defect sizing and detection of flaws in welds. It has been used to inspect over 200,000 welds on various pipeline projects worldwide.
Wall Thickness Gauge - (Magna-Mike 8600)
The document introduces the Magna-Mike 8600 thickness gauge. Key features of the 8600 include over 20 new features and improvements compared to previous models, such as two new probe designs, expanded target and thickness measurement ranges, a larger VGA display, and the ability to display live, minimum, maximum and difference readings simultaneously. It also has new calibration kits, programmable instrument lock, and the ability to export data to micro SD cards.
S 3000 radial inserter
This document describes Shenzhen Southern Machinery Sales and Service Co., Ltd and their radial inserter machine, the S-3000. Some key details include:
- The company has developed various component inserters since 2006 and attained a high-tech certification in 2010.
- The S-3000 radial inserter offers high throughput of up to 18,000 components per hour, flexibility to handle various component sizes and spans, and low cost of ownership.
- It allows 360 degree insertion and can handle components like capacitors, transistors, diodes, and connectors for applications in industries like lighting, appliances, vehicles, and more.
Weld probe presentation- Given at COTEQ, Porto Galinhas, Brazil, June 2013
This document discusses the advantages of using eddy current technology and specialized weld probes for weld inspection. It provides background on the development of weld probes and how they work. Weld probes allow inspection of welds through coatings with minimal lift-off sensitivity. They are well-suited for difficult-access inspections and have various applications in industries like offshore, nuclear, and rail. The document also covers standardization, equipment used, and concludes that weld probes provide a good alternative to other NDT methods for weld inspection.
Kurt pmi 10 08
This document summarizes various precision measuring instruments including outside micrometers, dial calipers, test indicators, dial indicators, electronic dial indicators, magnetic bases, and height gages. It provides specifications and features for different models ranging in measurement capacities from 0-1 inches to 0-12 inches and graduation precision from 0.0001 to 0.001 inches.
B m p/ rotary endodontic courses by indian dental academy
Indian Dental Academy: will be one of the most relevant and exciting training center with best faculty and flexible training programs for dental professionals who wish to advance in their dental practice,Offers certified courses in Dental implants,Orthodontics,Endodontics,Cosmetic Dentistry, Prosthetic Dentistry, Periodontics and General Dentistry.
PCB Manufacturer, Domestic Circuit Board Production and Prototype
Saturn Electronics Corporation is a leading printed circuit board fabricator that offers high-volume production and quick-turn prototype boards. It has strong financials with no debt and fully paid buildings and equipment. It owns three fabrication facilities in the US to enhance purchasing power and safeguard production. Saturn serves industries such as aerospace, automotive, defense, medical, and telecommunications with delivery times ranging from one day to three weeks. It has attained several certifications including AS9100, ISO9000, and ISO14001.
New corporate presentation july 2010
Dynamic & Proto Circuits Inc. is a 54,000 square foot facility that produces multilayer printed circuit boards using various solder mask options and new equipment like a HASL machine. The company invests in high speed drilling and via filling equipment to improve efficiency. Technology roadmaps show plans to reduce line widths and increase layer counts by 2012. The facility offers various substrate materials like FR-4 and BT epoxy and surface finishes including ENIG and HASL.
Dr.R.Narayanasamy - Formability of Automobile grade steels
The document discusses a research project analyzing the formability and wrinkling limits of various high strength steel sheets supplied by TATA Steel. Dr. R. Narayanasamy is the principal investigator, studying properties like tensile strength, forming limit diagrams, strain distribution, fractography, and texture. Tests were conducted on interstitial free steel, dual phase steel, and other varieties in thicknesses from 0.6mm to 2.0mm. Charts of chemical composition, microstructure, tensile properties, and forming limit diagrams are presented for each steel type.
Bill Godwin #6 Irrigation Pipe & Fittings Wed Jan 27
This document provides technical specifications for PVC and CPVC Schedule 80 fittings, unions, tank adapters, expansion joints, and saddles. It includes dimensional standards from ASTM for Schedule 80 pipe and socket dimensions as well as American National Standards for taper pipe threads. Recommendations are provided for installers regarding solvent weld connections, threaded connections, and general product use.
Bill Godwin #1 Working with PVC Irrigation Wed jan 27
This document provides technical specifications for PVC and CPVC Schedule 80 fittings, including dimensions according to ASTM standards. It lists nominal pipe sizes from 1/8" to 12" along with minimum wall thicknesses, tolerances, and other dimensional details. The document also provides injection and fabricated fitting dimensions and references, as well as part numbers and weights for PVC and CPVC tee fittings.
Testing/Manufacture/Lab product catalogue
LabproductTM is an ISO 9001 certified company that manufactures world class testing equipment. It has an in-house R&D center for continuous improvement and development of equipment using latest technologies. LabproductTM offers a wide range of automatic and digital testing equipment for industries such as government, defense, and private sectors. It provides complete testing solutions, equipment, training, and consultancy services to customers worldwide.
Phased array type b block
APPLICATION: Used for beam Characterization and evaluation of system performance characteristics. Use it as baseline block to determine long-term instrument performance changes, generate DAC Curves and Evaluate linear/ Angular resolution , Focusing ability and beam steering capabilities. With a variety of targets, this small, lightweight block is also perfect for customer demonstrations of phased array ultrasonic capabilities
Datasheet - Oil And Gas
Fine Tubes’ oil and gas tubing are used in the most challenging subsea and downhole conditions in seawater and sour oil well environments. Materials used are Austenitic, Super Austenitic, Duplex, Super Duplex, Titanium and Nickel Alloys. Seamless tubes are used for hydraulic tube and instrumentation tube applications, in onshore control panels, topside processing facilities, on subsea manifolds and templates up to 2,500m below the sea’s surface. Seam welded & redrawn tubes with orbital joints are used for subsea umbilicals, subsea control lines and chemical injection tubes. We can produce straight tubes or tube coils up to 10,000 m long. Coiled tubing is also used in onshore or topside hydraulic and instrumentation systems where the longer coils result in fewer connections and can increase the integrity of the overall system. These high pressure tubes need to be able to withstand huge amounts of pressure which is why our stainless steel coils for onshore applications are rated for use up to 60,000psi.
Sierra Circuits PCB Fabrication Capabilities
The document discusses Sierra Circuits, a printed circuit board resource company. It introduces Sierra's various business units for prototype and small production volumes, high-density interconnect technology, micro-electronics, offshore manufacturing, and Midwest production. It provides an overview of Sierra's manufacturing capabilities and technologies, including multi-layer boards up to 30 layers, a variety of materials, controlled impedance, blind and buried vias, and various surface finishes. The document encourages readers to stay tuned for more acquisitions, higher technology, and research that will change everything.
Diacutex Diamond Tool Products
This document appears to be a product catalogue for concrete cutting and grinding wheels. It lists various concrete cutting blades with different diameters, segment heights and applications that are suitable for cutting concrete, asphalt, stone and tiles. It also lists grinding cup wheels in various sizes for surface grinding of concrete floors. The blades and wheels can be used with handheld saws, table saws and angle grinders.
Similar to Phased array type a block (20)
built plans for single 18 inch subwoofer system.pdf
built plans for single 18 inch subwoofer system.pdf
Weld probe presentation- Given at COTEQ, Porto Galinhas, Brazil, June 2013
Weld probe presentation- Given at COTEQ, Porto Galinhas, Brazil, June 2013
B m p/ rotary endodontic courses by indian dental academy
B m p/ rotary endodontic courses by indian dental academy
PCB Manufacturer, Domestic Circuit Board Production and Prototype
PCB Manufacturer, Domestic Circuit Board Production and Prototype
Dr.R.Narayanasamy - Formability of Automobile grade steels
Dr.R.Narayanasamy - Formability of Automobile grade steels
Bill Godwin #6 Irrigation Pipe & Fittings Wed Jan 27
Bill Godwin #6 Irrigation Pipe & Fittings Wed Jan 27
Bill Godwin #1 Working with PVC Irrigation Wed jan 27
Bill Godwin #1 Working with PVC Irrigation Wed jan 27
More from Kirti NDT
Radiography Film Viewer
Features:
High Luminance.
Energy Saving.
Viewing Area: 12”x4”.
Adjustable Shutter for Viewing Area.
Electronic Brightness Control
Specification:
View Film Density up to 5.0 Density.
Input Voltage: 230Volt (±5%).
Power Consumption: 160W approx.
Heavy Aluminum heat sink.
Cooling Fan: 2 Nos.
Plug in Foot Switch.
Foot Switch & foot Switch Cable is shock Proof.
Mini lemo to mini lemo cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
Mini lemo to microdot cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
Lemo to mini lemo cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
Microdot to lemo Cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
Lemo to lemo cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
Bnc to mini lemo cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
BNC to Microdot Cable
We manufactures various types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
BNC to LEMO Cable
Lemo to BNC Cable is types of cables required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
BNC to BNC CABLE
BNC to BNC cable is Cable required for connecting transducers to the Flaw Detector. Standard cables are supplied for normal usage. They are available in various connector types and in various lengths.
Dual Cables with two connectors at each end to fit dual crystal transducer are also available.
Generally all cables are with 2 meters length.
Step wedge calibration block
APPLICATION: Used for Calibration of Ultrasonic Thickness Gauge, Straight Beam Thickness and Linearity Calibration etc.
SPECIFICATIONS: ✓ ASTM E797
AWS DS Calibration block
This document provides specifications for an AWS-DS calibration block used for straight beam distance, horizontal linearity, and sensitivity calibration. The block is 6 inches by 4 inches by 2 inches made of materials like carbon steel, stainless steel, or aluminum. It can be used for both inch and metric calibration requirements as the AWS standard does not specify a separate metric version.
AWS sensitivity block
APPLICATION: Sensitivity Block is AWS Type block also called SC Block used for sensitivity Calibration,
SPECIFICATIONS: ✓ ASTM E164, AWS-D1.1
INCH VERSION DIMENSIONS: ✓ 3.00” x 1.25” x 0.905” (L x W x H), 0.0625”Hole
METRIC VERSION DIMENSIONS: ✓ 75mm x 32mm x 22.6 (T x L x H), 1.6mm Hole
MATERIAL: ✓ Carbon steel, Stainless Steel, aluminum etc
Ball head telescopic gauge
Features: ➢ Used with an outside micrometer for measuring inside diameter of bores. ➢ Extra long for gaging deep and shallow holes, slots and similar work pieces. ➢ Gaging surface is fully hardened to insure long tool life. ➢ 4 sizes of gages are supplied in a fitted case. ➢ Spherical measuring faces hardened, Tool adjustment shaft Satin chrome finish ➢ Measuring Range 3-13mm (1/8"-1/2")
Instructions: ➢ A spring piston that telescopes in the bore enables internal diameter detection, which is measured with a micrometer or caliper. (Knurled locking device at the end.)
Using method: ➢ 1 Loosen the inner hole gauge and place it in the object to be measured. ➢ 2. Tighten clockwise and make one rotation to ensure tightening. ➢ 3. After the measurement is correct, tighten the lock clockwise. ➢ 4. After locking, measure the inner diameter data with a caliper.
Type A B C D ➢ Measuring range (Inch) :1/8"-1/5“, 1/5"-3/10" , 3/10" -2/5" , 2/5"-1/2" ➢ Measuring range (mm) : 3-5mm ,5-7.5mm, 7.5-10mm ,10-13mm ➢ Head diameter: 5mm, 5mm, 5mm, 5mm. ➢ Ball diameter: 3mm, 5mm, 7.5mm, 10mm. ➢ Length: 76mm, 79mm, 88mm, 92mm.
http
Drill gauge
Features: ➢ IDENTIFIES DRILL BITS SIZES- Helpful when working with older, unmarked drill bits and bits too small to fit diameter markings ➢ 29 MEASURING HOLES- Identified drill bits from 1/16 Inch to 1/2 Inch in 1/64th increments ➢ ETCHED MARKINGS- Black graduations to give high contrast and will not wear off ➢ NO MATH- Shows drill sizes in both inches and decimal equivalents ➢ DURABLE- Made from heavy duty, rustproof stainless steel ➢ 2-3/8" x 6-3/4" overall
http
Feeler gauge
The document describes a 32-blade feeler gauge set made of stainless steel. The feeler gauge blades measure thicknesses and gaps in both metric and imperial units, ranging from 0.0015 inches to 0.035 inches and 0.04 mm to 0.88 mm. The sizes are etched onto the blades for easy identification. The feeler gauge set can be used to measure gap widths and thicknesses for applications like machinery maintenance and repair.
Screw pitch gauge
Features: ➢ Fit for : Whitworth 55-Degree Threads & Metric 60-Degree Threads ➢ Material : Stainless Steel ➢ Size(Closed) : ~2 5/8 x 1/2 x 11/16inch(LWH) ➢ 52 folding leaves The leaves are individually stamped with accurately formed thread profiles Measures screw thread pitches between 0.25 6.0mm and 4 - 62 BSW(British Standard Whitworth) ➢ Package Content : 1 x Screw Pitch Gauge
Inch 55 ° specifications:
➢ 4G,4-1/2G, 5G, 6G, 7G, 8G, 9G, 10G, 11G, 12G, 13G, 14G, 16G, 18G, 19G, 20G, 22G, 24G, 25G, 26G, 28G , 30G, 32G, 36G, 40G, 48G, 60G, 62G
Metric 60 ° specifications:
➢ 0.25,0.3,0.35,0.4,0.45,0.5,0.6,0.7,0.75,0.8,0.9,1.0,1.25,1.5,1.75,2.0, 2.5,3.0,3.5,4.0,4.5,5.0,5.5 6.0
Telescopic gauge
Features: ➢ Spring loaded with locking knurled knob. Range: 5/16" - 6" (8mm to 150mm). ➢ Stainless Steel Construction, Titanium coating finish. ➢ Constant spring tension gives uniform contact pressure. ➢ Double action rigid handle with self centering feature for quick checking of holes, slots and recess up to 6" deep. ➢ Contact points are hardened tool steel and precision ground in the end measuring radius. ➢ Gage expands in a hole to be measured (locks in place and then removed to determine final hole size using a micrometer or calipers).
Tyre depth gauge
Tyre tread is the raised rubber of the Tyre which contacts the road. It is handy tool for passenger car , commercial vehicles as well as light commercial vehicles as timely checking of Tyre wear helps in minimizing errors and maximizing Tyre life Worn rubber can dramatically reduce stopping distances, as well as affecting steering and cornering ability.
Pocket fillet weld gauge
Kirti NDT Manufacture and Supply Pocket Fillet Weld Gauge,
Features: ➢ Pocket Size- Measures 8 Size Fillets ➢ Check Leg Length, Throat Size, Plus allowable Convexity ➢ All Increments Permanently Engraved ➢ Each Welder Can Carry a set for pre-Inspection ➢ Handy Key Chain Hold Set Together
More from Kirti NDT (20)
Recently uploaded
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
UNLOCKING HEALTHCARE 4.0: NAVIGATING CRITICAL SUCCESS FACTORS FOR EFFECTIVE I...
The Fourth Industrial Revolution is transforming industries, including healthcare, by integrating digital,
physical, and biological technologies. This study examines the integration of 4.0 technologies into
healthcare, identifying success factors and challenges through interviews with 70 stakeholders from 33
countries. Healthcare is evolving significantly, with varied objectives across nations aiming to improve
population health. The study explores stakeholders' perceptions on critical success factors, identifying
challenges such as insufficiently trained personnel, organizational silos, and structural barriers to data
exchange. Facilitators for integration include cost reduction initiatives and interoperability policies.
Technologies like IoT, Big Data, AI, Machine Learning, and robotics enhance diagnostics, treatment
precision, and real-time monitoring, reducing errors and optimizing resource utilization. Automation
improves employee satisfaction and patient care, while Blockchain and telemedicine drive cost reductions.
Successful integration requires skilled professionals and supportive policies, promising efficient resource
use, lower error rates, and accelerated processes, leading to optimized global healthcare outcomes.
官方认证美国密歇根州立大学毕业证学位证书原版一模一样
原版一模一样【微信：741003700 】【美国密歇根州立大学毕业证学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Advanced control scheme of doubly fed induction generator for wind turbine us...
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
Embedded machine learning-based road conditions and driving behavior monitoring
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building
Casting-Defect-inSlab continuous casting.pdf
Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting. Casting-Defect-inSlab continuous casting
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECT
The rivalry between prominent international actors for dominance over Central Asia's hydrocarbon
reserves and the ancient silk trade route, along with China's diplomatic endeavours in the area, has been
referred to as the "New Great Game." This research centres on the power struggle, considering
geopolitical, geostrategic, and geoeconomic variables. Topics including trade, political hegemony, oil
politics, and conventional and nontraditional security are all explored and explained by the researcher.
Using Mackinder's Heartland, Spykman Rimland, and Hegemonic Stability theories, examines China's role
in Central Asia. This study adheres to the empirical epistemological method and has taken care of
objectivity. This study analyze primary and secondary research documents critically to elaborate role of
china’s geo economic outreach in central Asian countries and its future prospect. China is thriving in trade,
pipeline politics, and winning states, according to this study, thanks to important instruments like the
Shanghai Cooperation Organisation and the Belt and Road Economic Initiative. According to this study,
China is seeing significant success in commerce, pipeline politics, and gaining influence on other
governments. This success may be attributed to the effective utilisation of key tools such as the Shanghai
Cooperation Organisation and the Belt and Road Economic Initiative.
NATURAL DEEP EUTECTIC SOLVENTS AS ANTI-FREEZING AGENT
NATURAL DEEP EUTECTIC SOLVENTS AS ANTI-FREEZING AGENT
Recently uploaded (20)
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODEL
UNLOCKING HEALTHCARE 4.0: NAVIGATING CRITICAL SUCCESS FACTORS FOR EFFECTIVE I...
UNLOCKING HEALTHCARE 4.0: NAVIGATING CRITICAL SUCCESS FACTORS FOR EFFECTIVE I...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Advanced control scheme of doubly fed induction generator for wind turbine us...
Generative AI leverages algorithms to create various forms of content
Generative AI leverages algorithms to create various forms of content
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressions
Engineering Drawings Lecture Detail Drawings 2014.pdf
Engineering Drawings Lecture Detail Drawings 2014.pdf
Embedded machine learning-based road conditions and driving behavior monitoring
Embedded machine learning-based road conditions and driving behavior monitoring
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECT
CHINA’S GEO-ECONOMIC OUTREACH IN CENTRAL ASIAN COUNTRIES AND FUTURE PROSPECT
NATURAL DEEP EUTECTIC SOLVENTS AS ANTI-FREEZING AGENT
NATURAL DEEP EUTECTIC SOLVENTS AS ANTI-FREEZING AGENT
gray level transformation unit 3(image processing))
gray level transformation unit 3(image processing))
Manufacturing Process of molasses based distillery ppt.pptx
Manufacturing Process of molasses based distillery ppt.pptx
Phased array type a block
- 1. KIRTI NDT & ENGINEERING SERVICES PHASED ARRAY TYPE A BLOCK http://www.kirtindt.in 1 PHASEDARRAYTYPEABLOCK APPLICATION: Phased Array “Type A” Calibration Block is used during the initial setup and calibration of phased array Ultrasonic Unit , This Block can be used to perform task such as beam angle verification , Calibration for Wedge Delay, Sensitivity Calibration, Performing DAC/TCG AND more MATERIAL: ✓ Carbon steel, Stainless Steel, aluminum etc. INCH VERSION DIMENSIONS: ✓ 1.000” thick x 4.000” Hight x 12.00” Long ✓ 4.000” and 2.000” Radii, 19 through holes at 0.040” diameter , 1 through hole at0.080” Diameter , 4FBH at 0.80” diameter x0.080”, 0.160”, 0.235” and 0.315” deep, 4FBH at 0.157” Diameter x0.040”, 0.120”, 0.200” and 0.275” Deep, 3FBH at 0.080” Diameter x 0.120 Deep machined into the 2.000” Radious, 4EDM Notches at .004”, .008”,.012” and .016” deep x 0.20” wide x1.00” Long, METRIC VERSION DIMENSIONS: ✓ 25.0mm thick x 100.0mm Hight x 300.0mm Long ✓ 100.0mm and 50.0mm Radii, 19 through holes at 1.0mm diameter, 1Through hole at 2.0mm diameter , 4FBH AT 2.0mm diameter x2.0mm, 4.0mm, 6.0mm an d8.0mm deep, 4FBH AT 4.0mm diameter x1.0mm, 3.0mm, 5.0mm and 7.0mm deep 3FBH AT 2.0mm diameter x 3.0mmdeep machined into the 50mm radius, 4EDM Notches at 0.1mm, 0.2mm, 0.3mm and 0.4mm deep x 0.5mm wide x25.0mm long
- 2. KIRTI NDT & ENGINEERING SERVICES Add: 707/B-Wing, Shree Sai Raj Park, Rajaji Path Road, Dombivali East, Thane, Maharashtra India-421201 Tel: +918779246578, +917718917422 What Sapp:+918779246578 Email: kirtindt@yahoo.in, kirti@kirtindt.in Website: www.kirtindt.in