PERT CPM ON A 2 STOREY RESIDENTIAL BUILDING
•
0 likes•1,963 views
The document appears to be a performance evaluation for a construction project containing scores in different categories including submittal on time, content, assigned task, and presentation with totals for three individuals: Mariano Matt, Gerald R. and Shiela Kuizon. It also references the owner, project title, designer, and team number for a construction project.
Report
Share
Report
Share
Download to read offline
Recommended
Construction Project Schedule Example- Residential Building
The document provides an example construction project schedule for building a residential building. It discusses planning the schedule by defining the project scope, stakeholders, and work breakdown structure. It then describes developing the schedule by defining activities, sequencing them, determining durations, and identifying the critical path. The example schedule is for a G+1 residential building and includes activities, durations, and relationships for structural works and finishing works.
Problems on bearing capacity of soil
This document provides 10 examples of problems related to bearing capacity of foundations. The examples calculate bearing capacity using Terzaghi's analysis for different soil and foundation conditions, including cohesionless and cohesive soils, square and strip footings, and considering the water table depth. One example compares results to field plate load tests. The solutions show calculations for determining soil shear strength parameters, factor of safety, and safe bearing capacity.
Numerical problem on bearing capacity is code terzaghi water table (usefulsea...
Numerical problem on bearing capacity is code terzaghi water table (usefulsearch.org) (useful search)
Compression member
The document discusses the design of compression members according to IS 800:2007. It defines compression members as structural members subjected to axial compression/compressive forces. Their design is governed by strength and buckling. The two main types are columns and struts. Common cross-section shapes used include channels, angles, and hollow sections. The effective length of a member depends on its end conditions. Slenderness ratio is a parameter that affects the load carrying capacity, with higher ratios resulting in lower capacity. Design involves checking the member for short or long classification, buckling curve classification, and calculating the design compressive strength. Examples are included to demonstrate the design process.
Solution Manual for Structural Analysis 6th SI by Aslam Kassimali
https://www.unihelp.xyz/solution-manual-structural-analysis-kassimali/
Solution Manual for Structural Analysis - 6th Edition SI Edition
Author(s): Aslam Kassimali
Solution Manual for 6th SI Edition (above Image) is provided officially. It include all chapters of textbook (chapters 2 to 17) plus appendixes B, C, D.
Design and analasys of a g+2 residential building
Design and analasys of a g+2 residential building => No nEEd FoH WoRk , Um gOod cOnsUMer oF PArentx MOnEy
This document summarizes the design of a one-way slab for a multi-story building. Key steps include:
1) Determining the effective span is 3.125m based on the room dimensions and support thickness.
2) Calculating the factored bending moment of 5.722 kNm/m based on the loads and effective span.
3) Checking that the provided depth of 150mm is greater than the required depth of 45.53mm.
4) Sizing the main reinforcement as 130mm^2 based on the factored moment and concrete properties.
5) Specifying 10mm diameter bars spaced at 300mm centers along the shorter span.NSCP 2010 , Volume 1
This document is the sixth edition of the National Structural Code of the Philippines (NSCP) Volume I, which provides requirements for designing buildings, towers, and other vertical structures. It was published in 2010 by the Association of Structural Engineers of the Philippines. The code contains chapters on minimum design loads, materials, and other topics to guide structural design in compliance with the latest standards. The foreword expresses pride in the publication and updates to the code to regulate structural design for safety.
Truss for indeterminacy Check
This document introduces different parts of a truss including joints, members, and reactions. It then provides the essential formulas for determining the stability and determinacy of trusses based on the number of joints (j), members (b), and reactive components (r). The remainder of the document works through examples of truss structures, calculating values for b, r, and j, and determining in each case whether the truss is stable/unstable and determinate/indeterminate based on the formulas.
Recommended
Construction Project Schedule Example- Residential Building
The document provides an example construction project schedule for building a residential building. It discusses planning the schedule by defining the project scope, stakeholders, and work breakdown structure. It then describes developing the schedule by defining activities, sequencing them, determining durations, and identifying the critical path. The example schedule is for a G+1 residential building and includes activities, durations, and relationships for structural works and finishing works.
Problems on bearing capacity of soil
This document provides 10 examples of problems related to bearing capacity of foundations. The examples calculate bearing capacity using Terzaghi's analysis for different soil and foundation conditions, including cohesionless and cohesive soils, square and strip footings, and considering the water table depth. One example compares results to field plate load tests. The solutions show calculations for determining soil shear strength parameters, factor of safety, and safe bearing capacity.
Numerical problem on bearing capacity is code terzaghi water table (usefulsea...
Numerical problem on bearing capacity is code terzaghi water table (usefulsearch.org) (useful search)
Compression member
The document discusses the design of compression members according to IS 800:2007. It defines compression members as structural members subjected to axial compression/compressive forces. Their design is governed by strength and buckling. The two main types are columns and struts. Common cross-section shapes used include channels, angles, and hollow sections. The effective length of a member depends on its end conditions. Slenderness ratio is a parameter that affects the load carrying capacity, with higher ratios resulting in lower capacity. Design involves checking the member for short or long classification, buckling curve classification, and calculating the design compressive strength. Examples are included to demonstrate the design process.
Solution Manual for Structural Analysis 6th SI by Aslam Kassimali
https://www.unihelp.xyz/solution-manual-structural-analysis-kassimali/
Solution Manual for Structural Analysis - 6th Edition SI Edition
Author(s): Aslam Kassimali
Solution Manual for 6th SI Edition (above Image) is provided officially. It include all chapters of textbook (chapters 2 to 17) plus appendixes B, C, D.
Design and analasys of a g+2 residential building
Design and analasys of a g+2 residential building => No nEEd FoH WoRk , Um gOod cOnsUMer oF PArentx MOnEy
This document summarizes the design of a one-way slab for a multi-story building. Key steps include:
1) Determining the effective span is 3.125m based on the room dimensions and support thickness.
2) Calculating the factored bending moment of 5.722 kNm/m based on the loads and effective span.
3) Checking that the provided depth of 150mm is greater than the required depth of 45.53mm.
4) Sizing the main reinforcement as 130mm^2 based on the factored moment and concrete properties.
5) Specifying 10mm diameter bars spaced at 300mm centers along the shorter span.NSCP 2010 , Volume 1
This document is the sixth edition of the National Structural Code of the Philippines (NSCP) Volume I, which provides requirements for designing buildings, towers, and other vertical structures. It was published in 2010 by the Association of Structural Engineers of the Philippines. The code contains chapters on minimum design loads, materials, and other topics to guide structural design in compliance with the latest standards. The foreword expresses pride in the publication and updates to the code to regulate structural design for safety.
Truss for indeterminacy Check
This document introduces different parts of a truss including joints, members, and reactions. It then provides the essential formulas for determining the stability and determinacy of trusses based on the number of joints (j), members (b), and reactive components (r). The remainder of the document works through examples of truss structures, calculating values for b, r, and j, and determining in each case whether the truss is stable/unstable and determinate/indeterminate based on the formulas.
MAX FAJARDO ESTIMATE.pdf
The document discusses concrete mixing and proportioning. It describes the components of concrete including cement, aggregates, and water. It provides proportions for different classes of concrete mixtures using volumetric measurements of cement, sand, gravel, and water. Guidelines are given for ensuring workability, strength, durability, and economy in concrete mixes. Conversion tables from inches to meters are also included.
Geo Technical Engineering (computing lateral earth pressure)
The document contains 10 examples involving calculation of earth pressures on retaining structures using Rankine's and Coulomb's theories. Example 1 calculates active earth pressure on a retaining wall with and without groundwater. Example 2 determines thrust on a wall with the water table rising. Example 3 finds active pressure, point of zero pressure and center of pressure for a cohesive soil. The remaining examples involve calculating earth pressures considering various soil properties and conditions.
Homework 1 (solution )
This document outlines homework problems related to soil properties. It includes 6 problems calculating various properties like water content, unit weight, void ratio, porosity, degree of saturation, and dry unit weight given information like the weight of moist soil, specific gravity, degree of saturation, and air content. The problems are solved showing the calculations and steps to arrive at the requested properties.
Problems on piles and deep footing
A group of 16 square piles extends 12 m into stiff clay soil, underlain by rock at 24 m depth. Pile dimensions are 0.3 m x 0.3 m. Undrained shear strength of clay increases linearly from 50 kPa at surface to 150 kPa at rock. Factor of safety for group capacity is 2.5. Determine group capacity and individual pile capacity.
The group capacity is calculated to be 1600 kN. The individual pile capacity is determined to be 100 kN. The factor of safety of 2.5 is then applied to determine the safe load capacity.
BT 1: Concrete and Admixtures
The document discusses the history and composition of concrete. It explains that modern concrete has greater compressive and tensile strength than ancient Roman concrete due to the use of Portland cement and steel reinforcement. The document also outlines different concrete mixtures based on proportion ratios and their recommended uses. It provides methods for calculating concrete needs and differentiates between concrete, cement, grout, and plaster.
Standard proctor test
This document summarizes a standard Proctor compaction test conducted on a soil sample. The test involves compacting the soil at different moisture contents in layers using a standardized hammer and measuring the dry unit weight. The maximum dry unit weight of 1.74 g/cm3 was found at an optimum moisture content of 13.7% based on the graph, however one data point exceeded the theoretical zero-air void curve, invalidating the test. The test will need to be redone to get accurate and dependable results.
Examples on total consolidation
1. The document provides examples of calculating consolidation parameters such as void ratio, coefficient of consolidation, and primary consolidation settlement from given soil testing data.
2. Parameters like initial void ratio, applied pressure, and thickness of soil layers are used to determine the change in stress and void ratio to then calculate settlement.
3. Several methods are presented to calculate the average effective stress and stress change at different points to then determine the consolidation settlement under different boundary conditions, stress histories, and soil properties.
Proctor Compaction Test
Determination of water content-dry density relation using light compaction. (Standard Proctor Test)
1. Maximum dry density (MDD) = 1.72 g/cm³
2. Optimum Moisture Content (OMC) = 18.3 %
3. Max. Saturation = 92.17 %
4. Min. Void Ratio = 0.549
The "acceptable zone" represents the zone of acceptable water content vs dry unit weight combinations based on typical current practice. The designer will usually require that the dry unit weight γd of the compacted soil be greater than or equal to a percentage P of the maximum dry unit weight Γd, max from a laboratory compaction test.
Out of four samples, in Delhi Silt highest value of max. dry density = 1.86 g/cc was achieved at a moisture content of 13% as compared to 1.72 g/cc for Dhanauri clay at 18.3%. It is seen that as the proportion of clay is increased in the soil mix the Optimum Moisture Increases and the Maximum Dry Density Decreases.
Structural Analysis, Hibbeler, 8th ed Textbook
This document provides tables and equations for analyzing beam deflections and slopes for various types of beams. It includes equations to determine the deflection (u), slope (v), maximum deflection (umax), and maximum slope (vmax) at different locations along beams subjected to a combination of loads, including concentrated forces (P), uniformly distributed loads (w), and moments (M). It also provides equations for determining deflections and slopes of beams with variable cross sections.
Tension members
Tension members are structural elements subjected to direct tensile loads. Their strength depends on factors like length of connection, size and spacing of fasteners, cross-sectional area, fabrication type, connection eccentricity, and shear lag. Failure can occur through gross section yielding, net section rupture, or block shear. Design involves selecting a member with sufficient gross area to resist factored loads in yielding, then checking strength considering net section rupture and block shear failure modes.
Lecture 4 classification of soil
This document provides an overview of soil classification systems, focusing on the Unified Soil Classification System (USCS) and the American Association of State Highway and Transportation Officials (AASHTO) system. It defines key aspects of each system such as grouping soils by grain size and plasticity. Examples are provided to demonstrate how to classify soils using index properties and test results based on the criteria of each system.
Estimating and-costing
This document provides an introduction to the subject of estimating and costing for the 2nd year intermediate vocational course in construction technology. It discusses key definitions like estimating, costing, and procedures for estimating. The importance of estimation and costing is explained. The data required for preparing an estimate like drawings, specifications, and rates is described. The document also discusses complete estimates, lump sum items, and work charged establishment. Measurement units for different construction items like earthwork, concrete, masonry, woodwork, and finishing works are listed with the applicable unit of measurement and payment.
Lecture 2 bearing capacity
This lecture discusses the bearing capacity of foundations. It introduces Terzaghi's bearing capacity theory, which evaluates the ultimate bearing capacity of shallow foundations based on a failure surface geometry. Terzaghi's equation for ultimate bearing capacity is presented. Meyerhof's and Hansen's theories are also introduced, which improved on Terzaghi's theory. Hansen's theory provides a more general bearing capacity equation that can be applied to both shallow and deep foundations. Safety factors are applied to the ultimate bearing capacity to determine allowable bearing capacity for foundation design. Settlement criteria may also control and limit the allowable bearing capacity in some cases.
Compaction characteristics of soil
Compaction, Its definition, uses, Factors affecting compaction
Field compaction methods and equipments. Solved Numerical and graphical representation of compaction curve and Zero air void line to obtain Optimum moistute content and Maximum dry density.
_lateral_earth_pressure_(foundation engineering)
The document outlines a course plan for a foundation engineering course. It includes 9 units that will be covered: introduction and site investigation, earth pressure, shallow foundations, pile foundations, well foundations, slope stability, retaining walls, and soil stabilization. It provides details on the number of lectures for each unit and the topics that will be covered in each lecture. Some key topics include shallow foundation design methods, pile load testing, earth pressure theories, and slope stability analysis techniques. References for the course are also provided.
Borrow pit-volumes
The document discusses soil phase relationships and concepts related to borrow pit volumes. It defines key terms like specific gravity, moisture content, void ratio, porosity, unit weights, and explores relationships between these terms. It also covers volume change factors related to excavation, loading and shrinkage. The borrow pit method for calculating soil volumes is described, involving taking elevation measurements at grid points to determine cut volumes. Example problems demonstrate calculations for cut volumes, hauled soil volumes, and volumes remaining in borrow pits.
Influence lines (structural analysis theories)
1. Influence lines represent the variation of reaction, shear, or moment at a specific point on a structural member as a concentrated load moves along the member. They are useful for analyzing the effects of moving loads.
2. To construct an influence line, a unit load is placed at different points along the member and the reaction, shear, or moment is calculated at the point of interest using statics. The values are plotted to show the influence of the load.
3. Influence lines allow engineers to determine the maximum value of a response (reaction, shear, moment) caused by a moving load and locate where on the structure that maximum occurs.
Schedule of Rates
A comprehensive presentation about:- What is S.O.R ? Do know different rates of Labors , Workers and machinery in Construction Field.
Flexural design of beam...PRC-I
Prepared by madam rafia firdous. She is a lecturer and instructor in subject of Plain and Reinforcement concrete at University of South Asia LAHORE,PAKISTAN.
Lec.3 General rules in quantitative survey. Quantity measuring. Rate analysis
Analysis of rates for various types of construction works provides very useful information for effective planning, control, organization and management.
AI assisted telemedicine KIOSK for Rural India.pptx
It gives the overall description of SIH problem statement " AI assisted telemedicine KIOSK for Rural India".
More Related Content
What's hot
MAX FAJARDO ESTIMATE.pdf
The document discusses concrete mixing and proportioning. It describes the components of concrete including cement, aggregates, and water. It provides proportions for different classes of concrete mixtures using volumetric measurements of cement, sand, gravel, and water. Guidelines are given for ensuring workability, strength, durability, and economy in concrete mixes. Conversion tables from inches to meters are also included.
Geo Technical Engineering (computing lateral earth pressure)
The document contains 10 examples involving calculation of earth pressures on retaining structures using Rankine's and Coulomb's theories. Example 1 calculates active earth pressure on a retaining wall with and without groundwater. Example 2 determines thrust on a wall with the water table rising. Example 3 finds active pressure, point of zero pressure and center of pressure for a cohesive soil. The remaining examples involve calculating earth pressures considering various soil properties and conditions.
Homework 1 (solution )
This document outlines homework problems related to soil properties. It includes 6 problems calculating various properties like water content, unit weight, void ratio, porosity, degree of saturation, and dry unit weight given information like the weight of moist soil, specific gravity, degree of saturation, and air content. The problems are solved showing the calculations and steps to arrive at the requested properties.
Problems on piles and deep footing
A group of 16 square piles extends 12 m into stiff clay soil, underlain by rock at 24 m depth. Pile dimensions are 0.3 m x 0.3 m. Undrained shear strength of clay increases linearly from 50 kPa at surface to 150 kPa at rock. Factor of safety for group capacity is 2.5. Determine group capacity and individual pile capacity.
The group capacity is calculated to be 1600 kN. The individual pile capacity is determined to be 100 kN. The factor of safety of 2.5 is then applied to determine the safe load capacity.
BT 1: Concrete and Admixtures
The document discusses the history and composition of concrete. It explains that modern concrete has greater compressive and tensile strength than ancient Roman concrete due to the use of Portland cement and steel reinforcement. The document also outlines different concrete mixtures based on proportion ratios and their recommended uses. It provides methods for calculating concrete needs and differentiates between concrete, cement, grout, and plaster.
Standard proctor test
This document summarizes a standard Proctor compaction test conducted on a soil sample. The test involves compacting the soil at different moisture contents in layers using a standardized hammer and measuring the dry unit weight. The maximum dry unit weight of 1.74 g/cm3 was found at an optimum moisture content of 13.7% based on the graph, however one data point exceeded the theoretical zero-air void curve, invalidating the test. The test will need to be redone to get accurate and dependable results.
Examples on total consolidation
1. The document provides examples of calculating consolidation parameters such as void ratio, coefficient of consolidation, and primary consolidation settlement from given soil testing data.
2. Parameters like initial void ratio, applied pressure, and thickness of soil layers are used to determine the change in stress and void ratio to then calculate settlement.
3. Several methods are presented to calculate the average effective stress and stress change at different points to then determine the consolidation settlement under different boundary conditions, stress histories, and soil properties.
Proctor Compaction Test
Determination of water content-dry density relation using light compaction. (Standard Proctor Test)
1. Maximum dry density (MDD) = 1.72 g/cm³
2. Optimum Moisture Content (OMC) = 18.3 %
3. Max. Saturation = 92.17 %
4. Min. Void Ratio = 0.549
The "acceptable zone" represents the zone of acceptable water content vs dry unit weight combinations based on typical current practice. The designer will usually require that the dry unit weight γd of the compacted soil be greater than or equal to a percentage P of the maximum dry unit weight Γd, max from a laboratory compaction test.
Out of four samples, in Delhi Silt highest value of max. dry density = 1.86 g/cc was achieved at a moisture content of 13% as compared to 1.72 g/cc for Dhanauri clay at 18.3%. It is seen that as the proportion of clay is increased in the soil mix the Optimum Moisture Increases and the Maximum Dry Density Decreases.
Structural Analysis, Hibbeler, 8th ed Textbook
This document provides tables and equations for analyzing beam deflections and slopes for various types of beams. It includes equations to determine the deflection (u), slope (v), maximum deflection (umax), and maximum slope (vmax) at different locations along beams subjected to a combination of loads, including concentrated forces (P), uniformly distributed loads (w), and moments (M). It also provides equations for determining deflections and slopes of beams with variable cross sections.
Tension members
Tension members are structural elements subjected to direct tensile loads. Their strength depends on factors like length of connection, size and spacing of fasteners, cross-sectional area, fabrication type, connection eccentricity, and shear lag. Failure can occur through gross section yielding, net section rupture, or block shear. Design involves selecting a member with sufficient gross area to resist factored loads in yielding, then checking strength considering net section rupture and block shear failure modes.
Lecture 4 classification of soil
This document provides an overview of soil classification systems, focusing on the Unified Soil Classification System (USCS) and the American Association of State Highway and Transportation Officials (AASHTO) system. It defines key aspects of each system such as grouping soils by grain size and plasticity. Examples are provided to demonstrate how to classify soils using index properties and test results based on the criteria of each system.
Estimating and-costing
This document provides an introduction to the subject of estimating and costing for the 2nd year intermediate vocational course in construction technology. It discusses key definitions like estimating, costing, and procedures for estimating. The importance of estimation and costing is explained. The data required for preparing an estimate like drawings, specifications, and rates is described. The document also discusses complete estimates, lump sum items, and work charged establishment. Measurement units for different construction items like earthwork, concrete, masonry, woodwork, and finishing works are listed with the applicable unit of measurement and payment.
Lecture 2 bearing capacity
This lecture discusses the bearing capacity of foundations. It introduces Terzaghi's bearing capacity theory, which evaluates the ultimate bearing capacity of shallow foundations based on a failure surface geometry. Terzaghi's equation for ultimate bearing capacity is presented. Meyerhof's and Hansen's theories are also introduced, which improved on Terzaghi's theory. Hansen's theory provides a more general bearing capacity equation that can be applied to both shallow and deep foundations. Safety factors are applied to the ultimate bearing capacity to determine allowable bearing capacity for foundation design. Settlement criteria may also control and limit the allowable bearing capacity in some cases.
Compaction characteristics of soil
Compaction, Its definition, uses, Factors affecting compaction
Field compaction methods and equipments. Solved Numerical and graphical representation of compaction curve and Zero air void line to obtain Optimum moistute content and Maximum dry density.
_lateral_earth_pressure_(foundation engineering)
The document outlines a course plan for a foundation engineering course. It includes 9 units that will be covered: introduction and site investigation, earth pressure, shallow foundations, pile foundations, well foundations, slope stability, retaining walls, and soil stabilization. It provides details on the number of lectures for each unit and the topics that will be covered in each lecture. Some key topics include shallow foundation design methods, pile load testing, earth pressure theories, and slope stability analysis techniques. References for the course are also provided.
Borrow pit-volumes
The document discusses soil phase relationships and concepts related to borrow pit volumes. It defines key terms like specific gravity, moisture content, void ratio, porosity, unit weights, and explores relationships between these terms. It also covers volume change factors related to excavation, loading and shrinkage. The borrow pit method for calculating soil volumes is described, involving taking elevation measurements at grid points to determine cut volumes. Example problems demonstrate calculations for cut volumes, hauled soil volumes, and volumes remaining in borrow pits.
Influence lines (structural analysis theories)
1. Influence lines represent the variation of reaction, shear, or moment at a specific point on a structural member as a concentrated load moves along the member. They are useful for analyzing the effects of moving loads.
2. To construct an influence line, a unit load is placed at different points along the member and the reaction, shear, or moment is calculated at the point of interest using statics. The values are plotted to show the influence of the load.
3. Influence lines allow engineers to determine the maximum value of a response (reaction, shear, moment) caused by a moving load and locate where on the structure that maximum occurs.
Schedule of Rates
A comprehensive presentation about:- What is S.O.R ? Do know different rates of Labors , Workers and machinery in Construction Field.
Flexural design of beam...PRC-I
Prepared by madam rafia firdous. She is a lecturer and instructor in subject of Plain and Reinforcement concrete at University of South Asia LAHORE,PAKISTAN.
Lec.3 General rules in quantitative survey. Quantity measuring. Rate analysis
Analysis of rates for various types of construction works provides very useful information for effective planning, control, organization and management.
What's hot (20)
Geo Technical Engineering (computing lateral earth pressure)
Geo Technical Engineering (computing lateral earth pressure)
Lec.3 General rules in quantitative survey. Quantity measuring. Rate analysis
Lec.3 General rules in quantitative survey. Quantity measuring. Rate analysis
Recently uploaded
AI assisted telemedicine KIOSK for Rural India.pptx
It gives the overall description of SIH problem statement " AI assisted telemedicine KIOSK for Rural India".
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
Slides for the 4th Presentation on LLM Fine-Tuning with QLoRA Presented by Anant, featuring DataStax Astra
Data Driven Maintenance | UReason Webinar
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
artificial intelligence and data science contents.pptx
What is artificial intelligence? Artificial intelligence is the ability of a computer or computer-controlled robot to perform tasks that are commonly associated with the intellectual processes characteristic of humans, such as the ability to reason.
› ...
Artificial intelligence (AI) | Definitio
Unit-III-ELECTROCHEMICAL STORAGE DEVICES.ppt
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
cnn.pptx Convolutional neural network used for image classication
Convolutional Neural Network used for image classification
Computational Engineering IITH Presentation
This Presentation will give you a brief idea about what Computational Engineering at IIT Hyderabad has to offer.
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Climate change's impact on the planet forced the United Nations and governments to promote green energies and electric transportation. The deployments of photovoltaic (PV) and electric vehicle (EV) systems gained stronger momentum due to their numerous advantages over fossil fuel types. The advantages go beyond sustainability to reach financial support and stability. The work in this paper introduces the hybrid system between PV and EV to support industrial and commercial plants. This paper covers the theoretical framework of the proposed hybrid system including the required equation to complete the cost analysis when PV and EV are present. In addition, the proposed design diagram which sets the priorities and requirements of the system is presented. The proposed approach allows setup to advance their power stability, especially during power outages. The presented information supports researchers and plant owners to complete the necessary analysis while promoting the deployment of clean energy. The result of a case study that represents a dairy milk farmer supports the theoretical works and highlights its advanced benefits to existing plants. The short return on investment of the proposed approach supports the paper's novelty approach for the sustainable electrical system. In addition, the proposed system allows for an isolated power setup without the need for a transmission line which enhances the safety of the electrical network
Software Engineering and Project Management - Introduction, Modeling Concepts...
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
Recently uploaded (20)
AI assisted telemedicine KIOSK for Rural India.pptx
AI assisted telemedicine KIOSK for Rural India.pptx
Data Control Language.pptx Data Control Language.pptx
Data Control Language.pptx Data Control Language.pptx
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
LLM Fine Tuning with QLoRA Cassandra Lunch 4, presented by Anant
artificial intelligence and data science contents.pptx
artificial intelligence and data science contents.pptx
Manufacturing Process of molasses based distillery ppt.pptx
Manufacturing Process of molasses based distillery ppt.pptx
Generative AI leverages algorithms to create various forms of content
Generative AI leverages algorithms to create various forms of content
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
4. Mosca vol I -Fisica-Tipler-5ta-Edicion-Vol-1.pdf
cnn.pptx Convolutional neural network used for image classication
cnn.pptx Convolutional neural network used for image classication
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Electric vehicle and photovoltaic advanced roles in enhancing the financial p...
Software Engineering and Project Management - Introduction, Modeling Concepts...
Software Engineering and Project Management - Introduction, Modeling Concepts...
Engineering Drawings Lecture Detail Drawings 2014.pdf
Engineering Drawings Lecture Detail Drawings 2014.pdf
PERT CPM ON A 2 STOREY RESIDENTIAL BUILDING
- 1. OFFICE OF THE BUILDING OFFICIAL LAND USE AND ZONING LINE AND GRADE CIVIL/ STRUCTURAL MECHANICAL SANITARY PLUMBING ARCHITECTURAL ELECTRICAL ELECTRONICS GEODETIC ENGINEER SHEET NO.: CHECKED BY: OWNER:PROJECT TITLE: DESIGNER:TEAM NO.: PERFORMANCE EVALUATION SUBMITTED ON TIME (20) CONTENT (50) ASSIGNED TASK (10) PRESENTATION (10) TOTAL (100) Mariano Matt Gerald R. Shiela kuizon . Construction Project Activities ACUNIN IF 4 1