gpon alu training

1. Turn Up Procedure

2. 2
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Objective
• After this section, you’ll be able to:
- Configure and turn-up a new ISAM
- Configure the ISAM’s IP-address
- Configure the network port, management VLAN and interface
- Set-up the SNMP management between 5520AMS and ISAM

3. 3
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Table of Contents
1. Standard Procedure
2. Alternative Scenario’s

4. 4
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Management communication
IHUB IP@
external MGT IHUB
Internal
VLAN 4094
External
VLAN
Internal management communication
- IC via VLAN4094.
External management
- Mgmt VLAN
IP addresses configurable by operator

5. 5
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure
Log on to the ISAM for the first time via Full CLI
- Connect via RS232 port on NANT-D, DCE RJ45 interface
ASCII coding no parity
9600 bps 1 stop bit
8 bits No flow control
- Choose CLI <C>
- First time login to the Full CLI
Login: isadmin
Password: i$@mad- (first time login)
New password: xxxxx
Confirm new password : xxxxx

6. 6
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Standard procedure
1

7. 7
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure using an access port: L1/L2 configuration
• Network port configuration
configure port nt-a:xfp:1 no shutdown
• Management V-VPLS configuration
configure service vpls 4080 customer 1 v-vpls vlan 4080 no shutdown
configure service vpls 4080 sap nt-a:xfp:1:4080

8. 8
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Basic concepts: Virtual Port
• ISAM supports interfaces on VLANs
• VLAN on IHUB are represented by V-VPLS
• Solution: IP interfaces are associated with v-VPLS via “virtual port”
L2
L3
IES
SAP
IP
SAPv-VPLS nt-a:xfp:1:4080

9. 9
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure using an access port: L3 configuration
• Management interface configuration
configure service ies 2 customer 1 create
configure service ies 2 interface "OAM" create
configure service ies 2 interface "OAM" address 172.24.27.183/24
configure service ies 2 interface "OAM" sap nt:vp:1:4080 create
configure service ies 2 no shutdown
• Default route configuration
configure router static-route 0.0.0.0/0 next-hop 172.24.27.1

10. 10
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Turn up procedure: SNMP
Make ISAM manageable from the AMS
configure system security snmp community public host-address <ipaddr/netmaskbits of AMS>
context nt ( on IACM)
configure system security snmp community NETMAN host-address <ipaddr/netmaskbits of
AMS> context ihub ( on IHUB)
Now you can create & supervise the ISAM on the AMS

11. 11
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Saving the management configuration
• When immediate reboot is needed after turn up
admin save
• To also save the management configuration in protected storage
admin software-mngt ihub database save-protected
• When re-activation with default db, the management config is restored
admin software-mngt oswp [1…2] activate with-default-db
• When re-activation with clear db, no management config is restored
admin software-mngt oswp [1…2] activate clear-db

12. 12
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Manage NE in AMS 5520
• Once turn-up procedure finished you need to manage the ISAM in the AMS (see
chapter on AMS Introduction)
• From the beginning, some basic decisions need to be taken to avoid unnecessary
reboots or other service disruption later during operation:
- Whether you are going to use NT-B and NTIO slot as universal slot instead (see equipment
configuration)
- xfp direction (up or down), if used for expansion (see equipment configuration)
- QoS basic setting (port of VLAN based, see QoS in Part 2)
- Creation of LAGs (see alternative scenario’s)

13. 13
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative scenario’s
2

14. 14
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 1: LAG – Link Aggregation Group
- All ports in a LAG must share the same characteristics, auto-negotiation must be
switched off.
- Changes can only be made to the primary port configuration, and changes to the
primary port configuration are automatically made to the non-primary ports.
One of the
links is
randomly
selected as
PRIMARY

15. 15
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 1: using an access port: L1/L2 configuration
with LAG• Network port configuration + LAG
configure port nt-a:xfp:1 no shutdown
configure port nt-a:xfp:1 ethernet no autonegociate
• LAG configuration
configure lag 10
configure lag 10
port nt-a:xfp:1
no shutdown

16. 16
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 1: using an access port: L1/L2 configuration with LAG
• Management V-VPLS configuration
configure service vpls 4080 customer 1 v-vpls vlan 4080 no shutdown
configure service vpls 4080 sap lag-10:4080
After these commands, you need to also do the L3 configuration and SNMP
configuration (cfr pag 8 and 9)

17. 17
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Alternative 2: Turn up procedure using a network port (from R4.1
onwards)
• Network port configuration
configure port nt-a:xfp:1 ethernet mode network
configure port nt-a:xfp:1 no shutdown

18. 18
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
7302/5520 Hands-on
Resetting the Alcatel 7302-7330 ISAM

19. 19
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
Hands-on
• Hidden Slide, see Notes Page
• Exercises
- Resetting the Alcatel 7302 ISAM

20. 20
COPYRIGHT © 2013 ALCATEL-LUCENT. ALL RIGHTS RESERVED.
www.alcatel-lucent.comwww.alcatel-lucent.com