Irrigation development in India, necessity, scope, benefits
and ill effects of irrigation, types of irrigation systems, methods of irrigation, physical
and chemical properties of soils, soil nutrients, classification of irrigable soils, suitability
of soils for irrigation, quality of irrigation water, soil water plant relations in irrigation,
measurement of soil moisture, field capacity, wilting point, available water , hydraulic
conductivity, water movement through soils.
Irrigation involves applying water artificially to land or soil to supply moisture for plant growth. There are various methods of irrigation that depend on the available water sources and infrastructure. Surface irrigation methods include border, check basin, and furrow irrigation. Subsurface irrigation applies water below the ground surface through underground trenches. Sprinkler and drip irrigation are pressurized methods that distribute water through pipes and emitters. The choice of irrigation method impacts water usage, uniformity of application, and suitability for different soil and crop types.
Irrigation methods can be categorized as gravity or flow irrigation and lift irrigation. Gravity irrigation uses water from a higher elevation conveyed via gravity through canals. It can be further divided into perennial and inundation irrigation. Common surface irrigation methods include furrow, border strip, basin, flooding, and wild flooding. Choosing a method depends on factors like soil type, slope, and crop. Surface methods are generally less efficient than pressurized systems but have lower infrastructure costs.
This power point presentation will give a complete idea of types of irrigation, water requirement of crops, duty, delta, canal revenue etc. This presentation also contain the numerical for complete understanding the concepts.
This document provides an overview of fundamental concepts in irrigation, including definitions of key terms, factors that influence irrigation efficiency, different irrigation methods, and crop water requirements. It defines irrigation as the artificial application of water to supply moisture for plant growth. Surface irrigation, sprinkler irrigation, and drip irrigation are described as the main methods. Critical growth stages and how crop water needs vary throughout growth are also covered.
Introduction about Irrigation BY SITARAM SAINISitaramSaini11
This document provides information about irrigation. It begins by defining irrigation as the process of artificially supplying water to soil for raising crops. It then discusses various surface, subsurface, sprinkler, and drip irrigation methods. It also covers factors that affect the choice of irrigation method such as soil characteristics, topography, water supply, and crop requirements. The document concludes by discussing concepts such as duty of water, delta, base period, culturable commanded area, and factors that influence the duty of water for crops.
1. Irrigation management involves scheduling irrigation appropriately based on soil type, crop water requirements, and other factors to efficiently use water resources.
2. Common methods of surface irrigation include border irrigation, check basin irrigation, and ridges and furrows irrigation which involve dividing fields into strips or basins and flooding or furrowing the land.
3. Factors considered in irrigation scheduling include soil type, crop water needs, available water supply, and allowing sufficient drying time between irrigations based on the crop's water depletion level. Monitoring soil moisture, plant conditions, and pan evaporation can help determine irrigation timing.
This document provides an overview of irrigation engineering in India. It defines irrigation engineering and discusses the necessity of irrigation given India's diverse climate and rainfall patterns. It then summarizes the history of irrigation development in India from ancient times to post-independence. The document also covers major, medium, and minor irrigation projects; water requirements of crops; principal crops in India; methods of irrigation including surface, subsurface and sprinkler; canals; tube well irrigation; dams; and issues like waterlogging and their remedial measures.
This document discusses different irrigation methods including surface, subsurface, and sprinkler irrigation. Surface irrigation methods such as flooding, furrow, and contour farming spread water over the land surface. Controlled flooding divides land into plots using levees. Furrow irrigation channels water along grooves. Contour farming uses horizontal terraces. Subsurface drip irrigation supplies water directly to plant roots through buried tubes. Sprinkler irrigation sprays water into the air simulating rain. Drip irrigation supplies small amounts of water directly to soil through emitters. Factors such as soil, topography, water supply, and crop requirements determine the suitable irrigation method.
Irrigation involves applying water artificially to land or soil to supply moisture for plant growth. There are various methods of irrigation that depend on the available water sources and infrastructure. Surface irrigation methods include border, check basin, and furrow irrigation. Subsurface irrigation applies water below the ground surface through underground trenches. Sprinkler and drip irrigation are pressurized methods that distribute water through pipes and emitters. The choice of irrigation method impacts water usage, uniformity of application, and suitability for different soil and crop types.
Irrigation methods can be categorized as gravity or flow irrigation and lift irrigation. Gravity irrigation uses water from a higher elevation conveyed via gravity through canals. It can be further divided into perennial and inundation irrigation. Common surface irrigation methods include furrow, border strip, basin, flooding, and wild flooding. Choosing a method depends on factors like soil type, slope, and crop. Surface methods are generally less efficient than pressurized systems but have lower infrastructure costs.
This power point presentation will give a complete idea of types of irrigation, water requirement of crops, duty, delta, canal revenue etc. This presentation also contain the numerical for complete understanding the concepts.
This document provides an overview of fundamental concepts in irrigation, including definitions of key terms, factors that influence irrigation efficiency, different irrigation methods, and crop water requirements. It defines irrigation as the artificial application of water to supply moisture for plant growth. Surface irrigation, sprinkler irrigation, and drip irrigation are described as the main methods. Critical growth stages and how crop water needs vary throughout growth are also covered.
Introduction about Irrigation BY SITARAM SAINISitaramSaini11
This document provides information about irrigation. It begins by defining irrigation as the process of artificially supplying water to soil for raising crops. It then discusses various surface, subsurface, sprinkler, and drip irrigation methods. It also covers factors that affect the choice of irrigation method such as soil characteristics, topography, water supply, and crop requirements. The document concludes by discussing concepts such as duty of water, delta, base period, culturable commanded area, and factors that influence the duty of water for crops.
1. Irrigation management involves scheduling irrigation appropriately based on soil type, crop water requirements, and other factors to efficiently use water resources.
2. Common methods of surface irrigation include border irrigation, check basin irrigation, and ridges and furrows irrigation which involve dividing fields into strips or basins and flooding or furrowing the land.
3. Factors considered in irrigation scheduling include soil type, crop water needs, available water supply, and allowing sufficient drying time between irrigations based on the crop's water depletion level. Monitoring soil moisture, plant conditions, and pan evaporation can help determine irrigation timing.
This document provides an overview of irrigation engineering in India. It defines irrigation engineering and discusses the necessity of irrigation given India's diverse climate and rainfall patterns. It then summarizes the history of irrigation development in India from ancient times to post-independence. The document also covers major, medium, and minor irrigation projects; water requirements of crops; principal crops in India; methods of irrigation including surface, subsurface and sprinkler; canals; tube well irrigation; dams; and issues like waterlogging and their remedial measures.
This document discusses different irrigation methods including surface, subsurface, and sprinkler irrigation. Surface irrigation methods such as flooding, furrow, and contour farming spread water over the land surface. Controlled flooding divides land into plots using levees. Furrow irrigation channels water along grooves. Contour farming uses horizontal terraces. Subsurface drip irrigation supplies water directly to plant roots through buried tubes. Sprinkler irrigation sprays water into the air simulating rain. Drip irrigation supplies small amounts of water directly to soil through emitters. Factors such as soil, topography, water supply, and crop requirements determine the suitable irrigation method.
Alternate wetting and drying (AWD) is an irrigation practice for rice that saves water and reduces greenhouse gas emissions while maintaining yields. It involves periodically drying and re-flooding rice fields. In Bangladesh, boro rice is fully irrigated while aman rice is partly irrigated. Research shows AWD can save 15-30% of the estimated 3,000-5,000 liters of water needed to produce one kilogram of rice, without lowering yields. The practice involves irrigating until the water table is 20cm below ground, then allowing the field to partially dry before re-flooding. This technique is being validated in Bangladesh and could help conserve irrigation water and reduce environmental impacts.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Soil properties like texture and structure determine a soil's water holding capacity. Plants obtain water from the soil through transpiration and rely on available soil water between field capacity and wilting point for growth.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Specifically, it discusses types of irrigation based on water application and duration. It also defines important terms related to irrigation engineering and concepts like culturable command area, water tables, and types of groundwater.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Soil properties like texture and structure determine a soil's water holding capacity. Plants obtain water from the soil through transpiration and rely on available soil water between field capacity and wilting point for growth.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water and plant interactions, as well as irrigation system design. It then discusses the necessity of irrigation due to insufficient or uneven rainfall. Benefits include increased crop yields and economic development, while ill effects can include rising water tables and loss of land. The document classifies irrigation systems and projects in India as major, medium or minor. It also examines soil-water relationships, including water holding capacity, field capacity, and wilting point.
This document provides an overview of irrigation engineering. It discusses the necessity of irrigation, benefits and ill effects, and development of irrigation in India. It describes the course goals to introduce concepts of soil, water, plant interactions and irrigation/drainage design. Key terms are defined, such as culturable command area. Different types of irrigation systems are classified, including flow and lift systems. Soil water relationships are also examined, including classifications of soil water and how water is held in soils.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Specifically, it discusses topics such as water holding capacity, field capacity, wilting point, and available soil water as they relate to plant growth. Types of groundwater and levels of water in soils are also explained.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Specifically, it discusses topics such as water content in soil, factors that influence water holding capacity, transpiration, and the relationships between soil properties, water retention, and plant growth.
The document discusses various methods of irrigation including surface, subsurface, sprinkler, and trickle irrigation. Surface irrigation methods include uncontrolled flooding, border strip, check, basin, and furrow irrigation. Subsurface irrigation applies water directly below the soil surface. Sprinkler irrigation sprays water into the air to fall on the soil surface. Trickle irrigation uses drippers to supply water directly to the soil at low rates. The choice of irrigation method depends on factors like field size/shape, soil characteristics, water availability, crop type, costs, and farmer experience.
The document describes four main methods of irrigation: surface irrigation, subsurface irrigation, sprinkler irrigation, and drip or trickle irrigation. Surface irrigation involves applying water to the soil surface through methods like flooding, furrows, borders, or basins. Subsurface irrigation applies water underground through trenches or pipes. Sprinkler irrigation sprays water into the air through nozzles, simulating rainfall. Drip irrigation delivers water slowly to the soil through a network of valves, pipes, tubing, and emitters. Each method has advantages and suitability for different crop and soil conditions.
Irrigation is the artificial application of water to soil to assist in growing crops. It is necessary in areas with insufficient or uneven rainfall. The main types of irrigation systems are surface irrigation, sprinkler irrigation, and drip irrigation. Surface irrigation includes uncontrolled flooding, border strip flooding, and furrow irrigation. Sprinkler and drip irrigation allow for more precise water application but have higher initial costs. Water quality must meet standards to avoid harming soils, crops, or human and animal health.
Irrigation methods are classified into four main types: surface irrigation, subsurface irrigation, sprinkler irrigation, and drip irrigation. Surface irrigation includes gravity-fed methods like flood, basin, border, and furrow irrigation. Water is applied to the soil surface and distributed by gravity. Subsurface irrigation involves applying water below the soil surface using trenches or perforated pipes. Sprinkler irrigation simulates natural rainfall by spraying water into the air through nozzles above the crop. Drip irrigation applies water slowly to the soil surface near plants through a network of valves, pipes, tubing, and emitters.
Furrow irrigation involves using small channels (furrows) between crop rows to carry water down slopes and allow it to infiltrate the soil. It is suitable for row crops and soils with moderate to slow water infiltration rates. Water is applied to furrows from supply channels via pipes or temporary breaches. The length of time water flows in furrows depends on factors like soil infiltration rate and the amount of water needed to replenish the root zone. Furrow irrigation works well for most soils except sandy soils with very high infiltration.
Surface irrigation methods like furrow and border strip irrigation distribute water over soil surfaces using gravity. Furrow irrigation involves making small channels along slopes for water to flow down, while border strip irrigation uses longer borders oriented with slopes. These methods are suited for row crops but often result in non-uniform water distribution and issues like waterlogging or salinity if not properly managed through drainage and controlling water amounts. Drip and sprinkler irrigation use pipes and emitters to supply water directly to plant roots, allowing more control and efficiency. The appropriate irrigation method depends on factors like crop type, water source, and land characteristics.
This document provides information about an irrigation engineering course taught by Engr. Ghulam Murtaza. It includes details about the instructor, course contents, textbooks, and introductory lectures. The course covers topics such as irrigation systems in Pakistan, water resources, types of irrigation, techniques of water distribution, the Indus Water Treaty, and features of the major rivers including the Sutlej, Ravi, and Chenab rivers.
Ground water recharge & water logging by Nikhil PakwanneNIKHIL PAKWANNE
The document discusses various methods of artificial groundwater recharging including (1) spreading method, (2) injection well method, and (3) river bank filtration method. It also covers subsurface drainage system layouts such as natural system, grid iron system, herringbone system, and double main system. Managing groundwater is important for irrigation and preventing issues like waterlogging.
The document discusses various methods of artificial groundwater recharging including (1) spreading method, (2) injection well method, and (3) river bank filtration method. It also covers subsurface drainage system layouts such as natural system, grid iron system, herringbone system, and double main system. Measures to prevent waterlogging like drainage systems, reducing irrigation intensity, and introducing crop rotation are also summarized.
An agricultural land is said to be waterlogging when the soil pores within the roof zone of the crops are saturated to such an extent that normal circulation of air within the soil pores is totally cut off and productivity of soil is affected. Waterlogging generally occurs because of over-irrigation , high water table and the poor water management.
The yield of crop is adversely affected when the depth of water table is equal to or less then the one given below.
This document discusses the importance of drainage in irrigated agricultural areas. It defines drainage as the removal of excess water from soil. Excess water can come from heavy rainfall or over-irrigation and can cause waterlogging of soils. Waterlogging deprives plant roots of oxygen and can lead to increased soil salinity. The document outlines various causes and effects of waterlogging and describes different types of drainage systems including surface drainage, subsurface drainage, vertical drainage, well drainage, controlled drainage, bio-drainage and their characteristics and advantages. Research on the impact of subsurface drainage in reclaiming waterlogged salt-affected soils in Andhra Pradesh, India is summarized which shows that drainage reduces soil salinity and increases crop yields.
This document discusses various irrigation methods including surface, subsurface, and pressurized irrigation. Surface irrigation methods like basin, border, and furrow irrigation distribute water over the field surface through controlled flooding. Pressurized methods like sprinkler and drip irrigation apply water under pressure through pipes and emitters. The selection of an irrigation method depends on factors like soil type, slope, crop type, water availability, and climate. Land leveling is also discussed to create suitable field surfaces for water flow control.
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
More Related Content
Similar to Introduction to irrigation engineering.pptx
Alternate wetting and drying (AWD) is an irrigation practice for rice that saves water and reduces greenhouse gas emissions while maintaining yields. It involves periodically drying and re-flooding rice fields. In Bangladesh, boro rice is fully irrigated while aman rice is partly irrigated. Research shows AWD can save 15-30% of the estimated 3,000-5,000 liters of water needed to produce one kilogram of rice, without lowering yields. The practice involves irrigating until the water table is 20cm below ground, then allowing the field to partially dry before re-flooding. This technique is being validated in Bangladesh and could help conserve irrigation water and reduce environmental impacts.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Soil properties like texture and structure determine a soil's water holding capacity. Plants obtain water from the soil through transpiration and rely on available soil water between field capacity and wilting point for growth.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Specifically, it discusses types of irrigation based on water application and duration. It also defines important terms related to irrigation engineering and concepts like culturable command area, water tables, and types of groundwater.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Soil properties like texture and structure determine a soil's water holding capacity. Plants obtain water from the soil through transpiration and rely on available soil water between field capacity and wilting point for growth.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water and plant interactions, as well as irrigation system design. It then discusses the necessity of irrigation due to insufficient or uneven rainfall. Benefits include increased crop yields and economic development, while ill effects can include rising water tables and loss of land. The document classifies irrigation systems and projects in India as major, medium or minor. It also examines soil-water relationships, including water holding capacity, field capacity, and wilting point.
This document provides an overview of irrigation engineering. It discusses the necessity of irrigation, benefits and ill effects, and development of irrigation in India. It describes the course goals to introduce concepts of soil, water, plant interactions and irrigation/drainage design. Key terms are defined, such as culturable command area. Different types of irrigation systems are classified, including flow and lift systems. Soil water relationships are also examined, including classifications of soil water and how water is held in soils.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Specifically, it discusses topics such as water holding capacity, field capacity, wilting point, and available soil water as they relate to plant growth. Types of groundwater and levels of water in soils are also explained.
This document provides an overview of irrigation engineering. It begins with the course goals of introducing concepts related to soil, water, and plant interactions, as well as irrigation system design. Key concepts covered include the necessity of irrigation, types of irrigation systems, soil-water relationships, and classifications of irrigation schemes in India. Specifically, it discusses topics such as water content in soil, factors that influence water holding capacity, transpiration, and the relationships between soil properties, water retention, and plant growth.
The document discusses various methods of irrigation including surface, subsurface, sprinkler, and trickle irrigation. Surface irrigation methods include uncontrolled flooding, border strip, check, basin, and furrow irrigation. Subsurface irrigation applies water directly below the soil surface. Sprinkler irrigation sprays water into the air to fall on the soil surface. Trickle irrigation uses drippers to supply water directly to the soil at low rates. The choice of irrigation method depends on factors like field size/shape, soil characteristics, water availability, crop type, costs, and farmer experience.
The document describes four main methods of irrigation: surface irrigation, subsurface irrigation, sprinkler irrigation, and drip or trickle irrigation. Surface irrigation involves applying water to the soil surface through methods like flooding, furrows, borders, or basins. Subsurface irrigation applies water underground through trenches or pipes. Sprinkler irrigation sprays water into the air through nozzles, simulating rainfall. Drip irrigation delivers water slowly to the soil through a network of valves, pipes, tubing, and emitters. Each method has advantages and suitability for different crop and soil conditions.
Irrigation is the artificial application of water to soil to assist in growing crops. It is necessary in areas with insufficient or uneven rainfall. The main types of irrigation systems are surface irrigation, sprinkler irrigation, and drip irrigation. Surface irrigation includes uncontrolled flooding, border strip flooding, and furrow irrigation. Sprinkler and drip irrigation allow for more precise water application but have higher initial costs. Water quality must meet standards to avoid harming soils, crops, or human and animal health.
Irrigation methods are classified into four main types: surface irrigation, subsurface irrigation, sprinkler irrigation, and drip irrigation. Surface irrigation includes gravity-fed methods like flood, basin, border, and furrow irrigation. Water is applied to the soil surface and distributed by gravity. Subsurface irrigation involves applying water below the soil surface using trenches or perforated pipes. Sprinkler irrigation simulates natural rainfall by spraying water into the air through nozzles above the crop. Drip irrigation applies water slowly to the soil surface near plants through a network of valves, pipes, tubing, and emitters.
Furrow irrigation involves using small channels (furrows) between crop rows to carry water down slopes and allow it to infiltrate the soil. It is suitable for row crops and soils with moderate to slow water infiltration rates. Water is applied to furrows from supply channels via pipes or temporary breaches. The length of time water flows in furrows depends on factors like soil infiltration rate and the amount of water needed to replenish the root zone. Furrow irrigation works well for most soils except sandy soils with very high infiltration.
Surface irrigation methods like furrow and border strip irrigation distribute water over soil surfaces using gravity. Furrow irrigation involves making small channels along slopes for water to flow down, while border strip irrigation uses longer borders oriented with slopes. These methods are suited for row crops but often result in non-uniform water distribution and issues like waterlogging or salinity if not properly managed through drainage and controlling water amounts. Drip and sprinkler irrigation use pipes and emitters to supply water directly to plant roots, allowing more control and efficiency. The appropriate irrigation method depends on factors like crop type, water source, and land characteristics.
This document provides information about an irrigation engineering course taught by Engr. Ghulam Murtaza. It includes details about the instructor, course contents, textbooks, and introductory lectures. The course covers topics such as irrigation systems in Pakistan, water resources, types of irrigation, techniques of water distribution, the Indus Water Treaty, and features of the major rivers including the Sutlej, Ravi, and Chenab rivers.
Ground water recharge & water logging by Nikhil PakwanneNIKHIL PAKWANNE
The document discusses various methods of artificial groundwater recharging including (1) spreading method, (2) injection well method, and (3) river bank filtration method. It also covers subsurface drainage system layouts such as natural system, grid iron system, herringbone system, and double main system. Managing groundwater is important for irrigation and preventing issues like waterlogging.
The document discusses various methods of artificial groundwater recharging including (1) spreading method, (2) injection well method, and (3) river bank filtration method. It also covers subsurface drainage system layouts such as natural system, grid iron system, herringbone system, and double main system. Measures to prevent waterlogging like drainage systems, reducing irrigation intensity, and introducing crop rotation are also summarized.
An agricultural land is said to be waterlogging when the soil pores within the roof zone of the crops are saturated to such an extent that normal circulation of air within the soil pores is totally cut off and productivity of soil is affected. Waterlogging generally occurs because of over-irrigation , high water table and the poor water management.
The yield of crop is adversely affected when the depth of water table is equal to or less then the one given below.
This document discusses the importance of drainage in irrigated agricultural areas. It defines drainage as the removal of excess water from soil. Excess water can come from heavy rainfall or over-irrigation and can cause waterlogging of soils. Waterlogging deprives plant roots of oxygen and can lead to increased soil salinity. The document outlines various causes and effects of waterlogging and describes different types of drainage systems including surface drainage, subsurface drainage, vertical drainage, well drainage, controlled drainage, bio-drainage and their characteristics and advantages. Research on the impact of subsurface drainage in reclaiming waterlogged salt-affected soils in Andhra Pradesh, India is summarized which shows that drainage reduces soil salinity and increases crop yields.
This document discusses various irrigation methods including surface, subsurface, and pressurized irrigation. Surface irrigation methods like basin, border, and furrow irrigation distribute water over the field surface through controlled flooding. Pressurized methods like sprinkler and drip irrigation apply water under pressure through pipes and emitters. The selection of an irrigation method depends on factors like soil type, slope, crop type, water availability, and climate. Land leveling is also discussed to create suitable field surfaces for water flow control.
Similar to Introduction to irrigation engineering.pptx (20)
Embedded machine learning-based road conditions and driving behavior monitoringIJECEIAES
Car accident rates have increased in recent years, resulting in losses in human lives, properties, and other financial costs. An embedded machine learning-based system is developed to address this critical issue. The system can monitor road conditions, detect driving patterns, and identify aggressive driving behaviors. The system is based on neural networks trained on a comprehensive dataset of driving events, driving styles, and road conditions. The system effectively detects potential risks and helps mitigate the frequency and impact of accidents. The primary goal is to ensure the safety of drivers and vehicles. Collecting data involved gathering information on three key road events: normal street and normal drive, speed bumps, circular yellow speed bumps, and three aggressive driving actions: sudden start, sudden stop, and sudden entry. The gathered data is processed and analyzed using a machine learning system designed for limited power and memory devices. The developed system resulted in 91.9% accuracy, 93.6% precision, and 92% recall. The achieved inference time on an Arduino Nano 33 BLE Sense with a 32-bit CPU running at 64 MHz is 34 ms and requires 2.6 kB peak RAM and 139.9 kB program flash memory, making it suitable for resource-constrained embedded systems.
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
Harnessing WebAssembly for Real-time Stateless Streaming PipelinesChristina Lin
Traditionally, dealing with real-time data pipelines has involved significant overhead, even for straightforward tasks like data transformation or masking. However, in this talk, we’ll venture into the dynamic realm of WebAssembly (WASM) and discover how it can revolutionize the creation of stateless streaming pipelines within a Kafka (Redpanda) broker. These pipelines are adept at managing low-latency, high-data-volume scenarios.
Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapte...University of Maribor
Slides from talk presenting:
Aleš Zamuda: Presentation of IEEE Slovenia CIS (Computational Intelligence Society) Chapter and Networking.
Presentation at IcETRAN 2024 session:
"Inter-Society Networking Panel GRSS/MTT-S/CIS
Panel Session: Promoting Connection and Cooperation"
IEEE Slovenia GRSS
IEEE Serbia and Montenegro MTT-S
IEEE Slovenia CIS
11TH INTERNATIONAL CONFERENCE ON ELECTRICAL, ELECTRONIC AND COMPUTING ENGINEERING
3-6 June 2024, Niš, Serbia
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024Sinan KOZAK
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
2. Irrigation can be defined as human manipulation of the hydrologic cycle to improve
crop production and quality and to decrease economic efforts of drought.
Irrigation is the artificial application of water to plants for their growth and maturity.
Irrigation water is supplied to supplement the water available from rainfall and the
contribution of soil moisture from ground water.
Irrigation
3. Necessity of Irrigation
Improvement of Perennial Crops.
• Some of the perennial crop requires water throughout the year. But rainfall is not uniform in all
seasons of the year. These crops cannot be produced perennially without water for all the
seasons.
Development of Desert Area.
• The dry and desert areas can be converted to a beautiful cropland if irrigation water can be
supplied as per need.
Insufficient Rainfall.
• Irrigation is necessary in the areas where rainfall is insufficient for the satisfactory growth of
the crops and the plants.
Uneven or Non-Uniform Rainfall Distribution
• If the distribution of rainfall in the zone of crop area is uneven and unpredictable.
4. Advantages and Disadvantages of Irrigation
Some of the Advantages of irrigation are as follows:
Increase of food production.
Modify soil or climate environment – leaching.
Lessen risk of catastrophic damage caused by drought.
Increase income & national cash flow.
Increase labour employment.
Increase standard of living.
Increase value of land.
National security thus self sufficiency.
Improve communication and navigation facilities.
Domestic and industrial water supply.
Improve ground water storage.
Generation of hydro-electric power
5. Disadvantages of Irrigation
Water logging.
Salinity and alkalinity of land
Ill aeration of soil.
Pollution of underground water.
Results in colder and damper climate causing outbreak of diseases like malaria.
6. Benefits of irrigation
1. Increase in crop yield:
The production of almost all types of crops can be increased by providing the right amount of later at the
right time, depending on its shape of growth. Such a controlled supply of water is possible only through
irrigation.
2. Protection from famine
The availability of irrigation facilities in any region ensures protection against failure of crops or famine
due to drought.
3. Cultivation of superior crops
With assured supply of water for irrigation, farmers may think of cultivating superior variety of crops or
even other crops which yield high return.
4. Elimination of mixed cropping
In rain-fed areas, farmers have a tendency to cultivate more than one type of crop in the same field such
that even if one dies without the required amount of water, at least he would get the yield of the other.
However, this reduces the overall production of the field.
7. 5. Economic development
With assured irrigation, the farmers get higher returns by way of crop production
throughout the year.
6. Hydro power generation:
Usually, in canal system of irrigation, there are drops or differences in elevation of canal
bed level at certain places. Although the drop may not be very high, this difference in
elevation can be used successfully to generate electricity.
7. Domestic and industrial water supply
Some water from the irrigation canals may be utilized for domestic and industrial water
supply for nearby areas. Compared to the irrigation water need, the water requirement for
domestic and industrial uses is rather small and does not affect the total flow much.
8. Irrigation trends in India Since 1947
India’s irrigation covered crop area was about 22.6 million hectares in 1951, and it increased to a potential
of 90 mha at the end of 1995, inclusive of canals and groundwater wells.
However, the potential irrigation relies of reliable supply of electricity for water pumps and maintenance,
and the net irrigated land has been considerably short.
According to 2001/2002 Agriculture census, only 58.1 million hectares of land was actually irrigated in
India. The total arable land in India is 160 million hectares (395 million acres).
According to the World Bank, only about 35% of total agricultural land in India was reliably irrigated in
2010.
India's irrigation is mostly groundwater well based. At 39 million hectares (67% of its total irrigation), India
has the world's largest groundwater well equipped irrigation system (China with 19 Mha is second, USA
with 17 Mha is third).
9. The type of irrigation methods can be broadly divided as under :
1. Surface irrigation method
2. Subsurface irrigation method
3. Sprinkler irrigation system
4. Drip irrigation system
10. 1. Flow irrigation
2. Lift irrigation
Flow Irrigation: Flow irrigation is that type of in
which flow of water to crop field from the source
takes place due to component of gravity force.
Surface Irrigation Method
11. Lift Irrigation:
Lift Irrigation is the process of lifting water normally from underground sources and
sometimes from surface source by pump, i.e. mechanical power or man or animal power and
then direct this lifted water is supplied to the agricultural field.
(In remote villages, if electric energy is not available in open well, shallow and deep tube
wells.)
12. Techniques for water distribution in Farms/Field
1. Border irrigation method
Borders are usually long uniformly graded strips of land separated by earth bunds (low ridges)
as shown in Figure
The essential feature of the border irrigation
is to provide an even surface over which the
water can flow down the slope with a nearly
uniform depth.
Each strip is irrigated independently by
turning in a stream of water at the upper end
as shown in the following Figure.
13. When the advancing water reaches the lower end of the border, the stream is turned off.
For uniform advancement of water front the borders must be properly leveled. The
border shown in the figures above are called straight borders.
14. The borders are sometimes laid along the elevation contours of the topography when the
land slope is excessive. That method of border is called contour border method of
irrigation
15. 2. Basin Irrigation
Basins are flat areas of land surrounded by low bunds. The bunds prevent the
water from flowing to the adjacent fields.
The basins are filled to desired depth and the water is retained until it
infiltrates into the soil. Water may be maintained for considerable periods of
time.
Basin method of irrigation can be formally divided into two, viz; the check
basin method and the ring basin method.
16. The other form of basin irrigation is the
ring basin method which is used for
growing trees in orchards. In this method,
generally for each tree, a separate basin is
made which is usually circular in shape.
The check basin method is the most common
method of irrigation used in India. In this
method, the land to be irrigated is divided into
small plots or basins surrounded by checks,
levees (low bunds).
17. 3.Furrow Irrigation
Furrows are small channels, which carry water down the land slope between the crop rows.
Water infiltrates into the soil as it moves along the slope. The crop is usually grown on
ridges between the furrows.
Water is applied to the
furrows by letting in water
from the supply channel,
either by pipe siphons or by
making temporary breaches
in the supply channel
embankment.
18. Furrow irrigation is suitable to most soils except sandy soils that have very high infiltration
water and provide poor lateral distribution water between furrows.
As compared to the other methods of surface irrigation, the furrow method is
advantageous as:
• Water in the furrows contacts only one half to one-fifth of the land surface, thus reducing
puddling and clustering of soils and excessive evaporation of water.
• Earlier cultivation is possible Furrows may be straight laid along the land slope, if the
slope of the land is small (about 5 percent) for lands with larger slopes, the furrows can be
laid along the contours.
19. Subsurface irrigation methods
The application of water to fields in this type of irrigation system is below the ground surface
so that it is supplied directly to the root zone of the plants.
The main advantages of these types of irrigation is reduction of evaporation losses and less
hindrance to cultivation works which takes place on the surface.
There may be two ways by which irrigation water may be applied below ground and these are
termed as:
• Natural sub-surface irrigation method
• Artificial sub-surface irrigation method
20. 1. Natural Sub-surface irrigation method
Under favorable conditions of topography and soil conditions, the water table may be close
enough to the root zone of the field of crops which gets its moisture due to the upward capillary
movement of water from the water table.
The natural presence of the water table may not be able to supply the requisite water throughout
the crop growing season.
However, it may be done artificially by constructing deep channels in the field which may be
filled with water at all times to ensure the presence of water table at a desired elevation below
the root zone depth.
21. Though this method of irrigation is excellent from both water distribution and Labour saving
points of view, it is favorable mostly for the following
• The soil in the root zone should be quite permeable.
• There should be an impermeable substratum below the water table to prevent deep
percolation of water.
• There must be abundant supply of quality water that is one which is salt free, otherwise
there are chances of upward movement of these salts along with the moisture likely to lead
the conditions of salt incrustation on the surface.
22. 2. Artificial subsurface irrigation method
The concept of maintaining a suitable water table just below the root zone is obtained by
providing perforated pipes laid in a network pattern below the soil surface at a desired depth.
It will function only if the soil in the root zone has high horizontal permeability to permit free
lateral movement of water and low vertical permeability to prevent deep percolation of water.
For uniform distribution of water percolating into the soil, the pipes are required to be very
closely spaced, say at about 0.5m.
Further, in order to avoid interference with cultivation the pipes have to be buried not less than
about 0.4m below the ground surface.
This method of irrigation is not very popular because of the high expenses involved, unsuitable
distribution of subsurface moisture in many cases, and possibility of clogging of the perforation
of the pipes.
23. 3. Sprinkler Irrigation System
Sprinkler irrigation is a method of applying water which is similar to natural rainfall but
spread uniformly over the land surface just when needed and at a rate less than the infiltration
rate of the soil so as to avoid surface runoff from irrigation.
This is achieved by distributing water through a system of pipes usually by pumping which is
then sprayed into the air through sprinklers so that it breaks up into small water drops which
fall to the ground.
The system of irrigation is suitable for undulating lands no land leveling is required as with
the surface irrigation methods.
Sprinklers are, however, not suitable for soils which easily form a crust.
The water that is pumped through the pump pipe sprinkler system must be free of suspended
sediments. As otherwise there would be chances of blockage of the sprinkler nozzles.
24. A typical sprinkler irrigation system consists of the following components:
1. Pump unit
2. Mainline and sometimes
sub mainlines
3. Laterals and Sprinklers
25. 4. Drip Irrigation System
Drip Irrigation system is sometimes called trickle irrigation and involves dripping water onto
the soil at very low rates (2-20 liters per hour) from a system of small diameter plastic pipes
filled with outlets called emitters or drippers.
Water is applied close to the plants so that only part of the soil in which the roots grow is
wetted, unlike surface and sprinkler irrigation, which involves wetting the whole soil profile.
With drip irrigation water, applications are more frequent than with other methods and this
provides a very favorable high moisture level in the soil in which plants can flourish.
26. A typical drip irrigation system consists of the following components:
Pump unit
Control Head
Main and sub main lines
Laterals
Emitters and drippers
27. • Soilis a heterogeneous mass consisting of a three phase system of solid, liquid and gas.
• Mineral matter, consisting of sand, silt and clay and organic matter form the largest
fraction of soil and serves as a framework (matrix) with numerous pores of various
proportions.
• Soil serves as a storage reservoir for nutrients and water needed for plant growth.
• Soil is a complex mass of mineral and organic particles.
The important properties (physical and chemical) that classify soil according to its
relevance to making crop production are:
Soil texture
Soil structure
Depth of Soil
28. Soil Texture
Soil texture is determined by the size and type of solid particles that make up the soil. Soil
particles may be mineral or organic.
For mineral soils, the texture classification is based on the relative proportion of the particles
less than 2 millimeters (mm) or 5/64th of an inch in size. As shown in Figure 1, the largest
particles are sand, the smallest are clay, and silt is in between. The soil texture is based on the
percentage of sand, silt and clay.
29.
30. Soil Structure
Soil structure refers to the grouping of
particles of sand, silt and clay into larger
aggregates of various sizes and shapes.
The processes of root penetration, wetting
and drying cycles, freezing and thawing,
and animal activity, combined with
inorganic and organic cementing agents,
produce soil structure (Figure).
.
31. Soil Depth
Soil depth refers to the thickness of the soil materials that provide structural support, nutrients
and water for plants.
A, B and C refer to the
different soil horizons
and 11C indicates a
different parent material
(for these soil series, it is
sand and gravel).
32. Different Types of Soil
• Residual Soil
It is formed due to disintegration of natural
rocks by the action of air, moisture, frost
and vegetation.
• Alluvial Soil
This soil is formed by the deposition of silt,
sediment by the river during flood time.
This soil is available in Indo-Gangetic
plains, the Brahmaputra basin and basin of
other big rivers of India.
33. Physical Properties of Soil
The physical properties of soil with respect to crop production, are texture, structure, bulk
density, porosity, consistency, temperature, colour and resistivity.
Soil physical properties regulate the movement, retention and availability of water and
nutrients to plants, and determine the flow of heat and air into, within and out of the soil.
Water movement through a root zone is hampered by any changes to soil physical
properties including changes in texture, compaction, porosity or organic matter content.
(Physical properties of soil vary through the depth of a soil profile)
34. Soil texture
It is determined by the relative proportion of soil separates sand, silt, and clay. Soil texture
and structure (the arrangement of particles) both have a direct impact on soil porosity.
Bulk density
It is the dry soil weight per volume of soil and is a good measure of porosity and
compaction. Generally, uncompacted soils containing 50% pore space with a bulk density of
1.1-1.6 g cm3 are ideal for agricultural soils.
Soil porosity
It consists of the void part of the soil volume and is occupied by gases or water. It is a
property that reflects the number and size of pores in the soil. Porosity results from the
arrangement of soil particles into aggregates with inter- and intra-aggregate pores, as well as
from root growth and faunal activity.
35. Soil consistency is the ability of soil materials to stick together.
Soil temperature is one of the most important properties that affect crop growth. The
major source of heat is sun and specific heat of soil is 0.2 Cal/g.
• The specific heat of soil increases with increase in moisture content.
• Soil temperature has considerable influence on several aspects of growth, especially in
early stages of crop.
Soil colour, besides being useful for classifying soils, is indirectly helpful in indicating
many properties of soil.
• Like, dark brown soils indicate high organic matter and fertility, red colour shows
good aeration, white colour accumulation of salts etc.
36. Chemical Properties of Soil
The soil’s chemical properties are inherited from the processes of soil formation, during
weathering and transport of the parent material from which the soil has formed.
Thus, the chemical nature of the rocks and minerals and the intensity of the weathering
processes are fundamental in determining the chemical properties of the soil.
Soil chemical properties including pH, electrical conductivity (EC), cation exchange
capacity (CEC), exchangeable Ca, Mg and K, exchangeable Al and hydrogen (H), C/N ratio
of added amendment, and organic matter (OM) content can impact soil N supply by
influencing the activity of microorganisms and the concentrations of NH4+ and NO3− in
the soil solution.
37. The pH of a soil indicates its acidity or alkalinity. pH influences nutrient availability, soil
physical condition and plant growth. Soil with <7 pH is acidic whereas, >8.5 pH is alkaline.
Electrical conductivity is reciprocal of the electrical resistance of the extract of the soil which
is one cm long and a cross sectional area of 1cm2
Soil solution- The solubility of a materials determines its ability to move in soils. Soluble salts
are chlorides, sulphates, nitrates and some carbonates and bicarbonates of Na, K, Mg, Ca and
NH4+.
• When a material dissolved in water, they dissociate into cations and anions.
Nutrients- Carbon, hydrogen and Oxygen are mainly obtained from water and air. Rest of
plant nutrients are obtained from mostly organic matter and mineral matter.
Weathering of minerals and mineralization of organic matter make the nutrients available to
plants.
38. Nutrient Optimum pH Range
N 6.0-8.0
P 6.5-7.5
K 6.0-7.5
S 6.0 and above
Ca & Mg 7.0-8.5
Fe 6.0 and below
Mn 5.0-6.5
Bo, Cu, Zn 5.0-7.0
Mo 7.0 and above
39. Types of Soil water or Soil Moisture
• When water fills the soil surface by irrigation or by rainwater, it is absorbed by the soil. The amount
of absorption is different for different types of soil. The water absorbed by pores is called soil water
or soil moisture.
Some of the soil water are:
• Gravitational Water
It is that water which drains into the soil under the influence of gravity. After irrigation and rainfall
this water remains in the soil and saturates it preventing circulation of air and void spaces.
• Capillary Water
Below the gravitational water, a part of water held by the soil by the capillary action of surface
tension force against gravity. This part of water is absorbed by the root zone of the crop.
• Hygroscopic Water
Water attached to soil particles through loose chemical bond is termed as hygroscopic water. This
water can be removed from the soil only by application of heat. During draught situation, plant roots
can extract small fraction of this water.
40.
41. Irrigation Water Quality
The quality of some water sources is not suitable for irrigating crops. Irrigation water must
be compatible with the crops and soils to which it will be applied.
The Soil and Water Testing Laboratory in the Soil Science Department at NDSU provides
soil and water compatibility recommendations for irrigation.
The quality of water for irrigation purposes is determined by its total dissolved salt
content. An analysis of water for irrigation should include the cations (calcium,
magnesium and sodium) and the anions (bicarbonate, carbonate, sulfate and chloride).
42. Irrigation Water Classification
The two most important factors to look for in an irrigation water quality analysis are
the total dissolved solids (TDS) and the sodium adsorption ratio (SAR).
The TDS of a water sample is a measure of the concentration of soluble salts in a
water sample and commonly is referred to as the salinity of the water.
(The electrical conductivity (EC) of a water sample often is used as a proxy for TDS.)
The SAR of a water sample is the proportion of sodium relative to calcium and
magnesium. Because it is a ratio, the SAR has no units.
43. Laboratories that perform
irrigation water analysis may
provide a suitability classification
based on a system developed at
the U.S. Salinity Laboratory in
California.
This classification system
combines salinity and sodicity.
For example, a water sample
classified as C3-S2 would have a
high salinity rating and a medium
SAR rating.
44. Salinity
C1 - Low-salinity water: Can be used for irrigation with most crops on most soils with little
likelihood that soil salinity will develop.
C2 - Medium-salinity water: Can be used if a moderate amount of leaching occurs. Plants
with moderate salt tolerance can be grown in most cases without special practices for salinity
control.
C3 - High-salinity water: Cannot be used on soils with moderately slow to very slow
permeability.
C4 - Very high salinity water: Is not suitable for irrigation under ordinary conditions but may
be used occasionally under very special circumstances. (The soils must have rapid
permeability, drainage must be adequate.)
45. Sodium
S1 - Low-sodium water: Can be used for irrigation on almost all soils with little danger of the
development of harmful levels of exchangeable sodium.
S2 - Medium-sodium water: Will present an appreciable sodium hazard in fine-textured soils,
especially under low leaching conditions. This water may be used on coarse-textured soils with
moderately rapid to very rapid permeability.
S3 - High-sodium water: Will produce harmful levels of exchangeable sodium in most soils and
requires special soil management, good drainage, high leaching and high organic matter
additions.
S4 - Very high sodium water: Generally is unsatisfactory for irrigation purposes except at low
and perhaps medium salinity.
46. The Interaction Between Soil and Water
Soil is a medium that stores and moves water.
If a cubic foot of a typical silt loam topsoil were separated into its component parts, about 45 percent of the
volume would be mineral matter (soil particles), organic residue would occupy about 5 percent of the volume
and the rest would be pore space.
Water is held in soil in two ways:
As a thin coating on the outside of soil particles and in the pore spaces. Soil water in the pore spaces can be
divided into two different forms: gravitational water and capillary water.
47. The two primary ways that water is held in the soil for plants to use are capillary and
gravitational forces.
Gravitational water generally moves quickly downward in the soil due to the force of
gravity. Capillary water is the most important for crop production because it is held by soil
particles against the force of gravity.
Water Holding Capacity of Soils
The four important levels of soil moisture content reflect the availability of water in the soil.
These levels commonly are referred to as
1) saturation,
2) field capacity,
3) wilting point and
4) oven dry.
48. • When a soil is saturated, the soil pores are filled with water and nearly all of the air in the
soil has been displaced by water.
• The water held in the soil between saturation and field capacity is gravitational water.
• Field capacity is defined as the level of soil moisture left in the soil after drainage of the
gravitational water.
• Water held between field capacity and the wilting point is available for plant use.
Field capacity
• The wilting point is defined as the soil moisture content at which most plants cannot
exert enough force to remove water from small pores in the soil.
• Most crops will be damaged permanently if the soil moisture content is allowed to reach
the wilting point. In many cases, yield reductions may occur long before this point is
reached.
Wilting point
49. • Capillary water held in the soil beyond the wilting point can be removed only by
evaporation. When dried in an oven, nearly all water is removed from the soil.
• "Oven dry" moisture content is used to provide a reference for measuring the other
three soil moisture contents.
Oven dry
Available soil water content
commonly is expressed as
inches per foot of soil.
50. How Plants Get Water From Soil
• Most of the water that enters the plant roots does not stay in the plant.
• Less than 1 percent of the water withdrawn by the plant actually is used in photosynthesis
( assimilated by the plant).
• The rest of the water moves to the leaf surfaces, where it transpires (evaporates) to the
atmosphere.
• The rate at which a plant takes up water is controlled by its physical characteristics, the
atmosphere and soil environment.
As water moves from the soil into the roots, through
the stem, into the leaves and through the leaf stomata
to the air, it moves from a low water tension to a
high water tension.
51. • During the course of a growing season, plants will extract about 40 percent of their water
from the top quarter, 30 percent from the second quarter, 20 percent from the third quarter
and 10 percent from the bottom quarter of the root zone.
• Plants can extract only the soil water that is
in contact with their roots.
• The course of a growing season, plants
generally extract more water from the upper
part of their root zone than from the lower
part
Editor's Notes
In this method, the land to be irrigated is divided into small plots or basins surrounded by checks, levees (low bunds).
The length of time the water is to flow in the furrows depends on the amount of water required to replenish the root zone and the infiltration rate of the soil and the rate of lateral spread of water in the soil.