Hunan Guanglian Photoelectricity Technologies Co., Ltd is a leading global manufacturer of fiber optic cables. It has over 300 equipment for manufacturing various cables and over 100 testing equipment. It produces cables for outdoor, indoor, submarine, and other applications. Customers can be assured that working with GL Technology will lead to a successful fiber optic cable solution and experience.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Euromold elbow connectors, Euromold tee connectors, Euromold bushings (oil insulated) and Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series, 400TB 440TB Features :
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
T&D UK with the support of Nexans provide installation training and certification for experienced high voltage cable jointers up to 33kV.
400 Series Interface B Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface B bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
SEB Cable Laying & Cable Pulling Equipment enables the installation of LV-HV power, fibre optic, telecoms, subsea cables and umbilicals into cable duct or cable trench.
T&D service utilities, power, construction, rail, mining, street lighting, subsea, offshore, oil, gas and petrochemical industries with global market leading SEB Cable Laying & Cable Pulling Equipment.
T&D distribute the complete range of SEB Cable Pulling and Cable Laying Equipment for low and high voltage (LV-HV) power cable installations into underground trench or cable duct - this includes XLPE, PILC, EPR, waveform, service cables, triplex, 11kV, 33kV, EHV, fibre optic, telecoms and street lighting cables. We supply cable rollers, cable socks, cable jacks, drum trailers, cable pulling lubricant, underground cable protection (Stokbord & Tape Tile Cable Covers) and conduit duct rod - we service the utility cable laying contractor, electrical contractor and export markets.
SEB Cable Laying Solutions for Renewable Energy Projects
A comprehensive cable laying package includes cable rollers (straight and corner), cable drum jacks, cable winches and cable socks including stainless steel socks for pulling large diameter, high voltage subsea power cables and umbilicals up to 400kV.
200 Series Interface A Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface A bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Euromold elbow connectors, Euromold tee connectors, Euromold bushings (oil insulated) and Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series, 400TB 440TB Features :
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
T&D UK with the support of Nexans provide installation training and certification for experienced high voltage cable jointers up to 33kV.
400 Series Interface B Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface B bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
SEB Cable Laying & Cable Pulling Equipment enables the installation of LV-HV power, fibre optic, telecoms, subsea cables and umbilicals into cable duct or cable trench.
T&D service utilities, power, construction, rail, mining, street lighting, subsea, offshore, oil, gas and petrochemical industries with global market leading SEB Cable Laying & Cable Pulling Equipment.
T&D distribute the complete range of SEB Cable Pulling and Cable Laying Equipment for low and high voltage (LV-HV) power cable installations into underground trench or cable duct - this includes XLPE, PILC, EPR, waveform, service cables, triplex, 11kV, 33kV, EHV, fibre optic, telecoms and street lighting cables. We supply cable rollers, cable socks, cable jacks, drum trailers, cable pulling lubricant, underground cable protection (Stokbord & Tape Tile Cable Covers) and conduit duct rod - we service the utility cable laying contractor, electrical contractor and export markets.
SEB Cable Laying Solutions for Renewable Energy Projects
A comprehensive cable laying package includes cable rollers (straight and corner), cable drum jacks, cable winches and cable socks including stainless steel socks for pulling large diameter, high voltage subsea power cables and umbilicals up to 400kV.
200 Series Interface A Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface A bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded, high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold separable elbow connectors are designed to terminate high voltage polymeric (XLPE EPR) screened (copper wire or copper tape) cables to CENELEC Interface Type B (400amp) bushings with 14mm plug-in pins, up to 33kV.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold straight plug connectors, Nexans Euromold bushings (air, oil and gas insulated switchgear) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Euromold Connectors 400 Series Interface Type B Bushing
* Connector Type : 14mm Plug-In Pin Contact
* Voltage Range : 11/12kV-33/36kV
* Current Rating : 400amps
* Specification : CENELEC EN50180 & EN50181
Euromold 400LR Elbow Connectors are used with 400 Series Interface B Bushing.
700 Series Interface E Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface E bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables. 700 Series Interface E, Elastimold Bushings * Bushing Voltage Range 33kV-36kV * Bushing Current Rating 800Amps & 1250Amps * Bushing Type 5/8" Bolted Aluminium Insert Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 700 Series Connectors - 750LR Tee Connectors & 775LR Tee Connectors 800-1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the Elastimold high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination. HV High Voltage Cable Connectors, Specification - Elastimold dead-break separable cable connectors suit all international high voltage bushing interfaces for the termination of HV cable into switchgear, transformers and motors. Elastimold cable connectors terminate high voltage power cables (typically 11kV, 15kV, 24kV, 33kV, 36kV up to 52kV) into SF6 GIS gas insulated switchgear including Schneider, ABB, Areva and Siemens. Elastimold cable connectors meet the requirements of ANSI/IEEE 386 & 404 and CENELEC EN50180 & EN50181 for high voltage "dead-break" cable connection, i..e connectors installed and terminated onto un-energised high voltage power cable. US specification "load-break" cable connectors for high voltage energised cable termination are available. High Voltage Cable Connectors - Elastimold cable connectors (elbow and straight types) are specified to terminate XLPE or EPR insulated high voltage power cables with copper tape or copper wire screens up to 52kV. Elastimold cable connectors are available to suit and terminate lead covered HV cables for hydro-carbon industries (oil, gas, petrochemicals) with ATEX certification for hazardous area Zones 1 and Zones 2.
The Nexans Euromold compact version screened separable connector is suitable for high voltage HV cable termination up to 33kV. Interface Type C Euromold M16 bolted tee connectors up to 33kV are designed to connect and terminate polymeric (XLPE EPR) cables to M16 bolted 400 series equipment bushings. Nexans Euromold connectors are supplied in sets of three phases.
Nexans Euromold Kit Contents: 3 x connector housings, 3 x size sensitive cable reducers, 3 x conductor contact lug, 3 x clamping screws and 3 x insulating plugs & caps.
Catalog busbar ls 06. busduct presentation e series rev 2Dien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Underground Cable Accessories
Elastimold® offers the industry's most complete package for managing underground cable connections.
Broad Product Range..
Elastimold accessories, available from 5kV to 138kV, connect, ground, splice, terminate and protect underground cable.
Elastimold Innovation
Elastimold’s long, innovative history includes pioneering such products as extended and repair elbows, jacket seal elbows, and shrink-fit joints.
Do công ty LS Cable sản xuất tại Hàn Quốc. Sản phẩm này thuộc nhóm sản phẩm chất lượng cao cấp nhất trên thế giới (dùng lớp cách điện Epoxy theo công nghệ nhúng của Mỹ), và chất lượng ngang hàng với các nhà sản xuất Mỹ / EU. Sản phẩm này cung cấp cho Sân bay Changi Singapore là công trình lớn nhất S.E.A, và công trình Keangnam Landmark Hà nội ( là công trình lớn nhất tại Việt nam). Hiện tại sản phẩm này đang được bán đại trà trên toàn thế giới, và thuộc top 5 nhà sản xuất hàng đầu thế giới. Đây cũng là sản phẩm cao cấp nhất được cung cấp tại Việt Nam với thời gian bảo hành lên đến 2 năm kể từ ngày đóng điện an toàn. Hiện LS Cable đã cung cấp hơn 50 công trình tại VN, trong đó có những công trình tiêu biểu như : Royal City, Time City, Crowne Plaza HN, Petroland Tower HCM, Petrovietnam Power Landmark, Crescent Mall HCM, Bệnh viện Đại Học Y Dược, Bệnh Viện Đa Khoa Hoàn Mỹ, Bệnh Viện Miền Đông, Diamond Island HCM, Kenton Residence HCM, Dargon Hill Residence, Riverside Residence Phú Mỹ Hưng, River Park Phú Mỹ Hưng, Saigon Airport Plaza, Khách sạn Grand, Khách sạn 5 sao Le Meriden, Royal City HN, Sail Tower ….Sản phẩm này cũng chiếm thị phần số 1 tại Singapore hiện nay.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded, high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold separable elbow connectors are designed to terminate high voltage polymeric (XLPE EPR) screened (copper wire or copper tape) cables to CENELEC Interface Type B (400amp) bushings with 14mm plug-in pins, up to 33kV.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold straight plug connectors, Nexans Euromold bushings (air, oil and gas insulated switchgear) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Euromold Connectors 400 Series Interface Type B Bushing
* Connector Type : 14mm Plug-In Pin Contact
* Voltage Range : 11/12kV-33/36kV
* Current Rating : 400amps
* Specification : CENELEC EN50180 & EN50181
Euromold 400LR Elbow Connectors are used with 400 Series Interface B Bushing.
700 Series Interface E Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface E bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables. 700 Series Interface E, Elastimold Bushings * Bushing Voltage Range 33kV-36kV * Bushing Current Rating 800Amps & 1250Amps * Bushing Type 5/8" Bolted Aluminium Insert Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 700 Series Connectors - 750LR Tee Connectors & 775LR Tee Connectors 800-1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the Elastimold high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination. HV High Voltage Cable Connectors, Specification - Elastimold dead-break separable cable connectors suit all international high voltage bushing interfaces for the termination of HV cable into switchgear, transformers and motors. Elastimold cable connectors terminate high voltage power cables (typically 11kV, 15kV, 24kV, 33kV, 36kV up to 52kV) into SF6 GIS gas insulated switchgear including Schneider, ABB, Areva and Siemens. Elastimold cable connectors meet the requirements of ANSI/IEEE 386 & 404 and CENELEC EN50180 & EN50181 for high voltage "dead-break" cable connection, i..e connectors installed and terminated onto un-energised high voltage power cable. US specification "load-break" cable connectors for high voltage energised cable termination are available. High Voltage Cable Connectors - Elastimold cable connectors (elbow and straight types) are specified to terminate XLPE or EPR insulated high voltage power cables with copper tape or copper wire screens up to 52kV. Elastimold cable connectors are available to suit and terminate lead covered HV cables for hydro-carbon industries (oil, gas, petrochemicals) with ATEX certification for hazardous area Zones 1 and Zones 2.
The Nexans Euromold compact version screened separable connector is suitable for high voltage HV cable termination up to 33kV. Interface Type C Euromold M16 bolted tee connectors up to 33kV are designed to connect and terminate polymeric (XLPE EPR) cables to M16 bolted 400 series equipment bushings. Nexans Euromold connectors are supplied in sets of three phases.
Nexans Euromold Kit Contents: 3 x connector housings, 3 x size sensitive cable reducers, 3 x conductor contact lug, 3 x clamping screws and 3 x insulating plugs & caps.
Catalog busbar ls 06. busduct presentation e series rev 2Dien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Underground Cable Accessories
Elastimold® offers the industry's most complete package for managing underground cable connections.
Broad Product Range..
Elastimold accessories, available from 5kV to 138kV, connect, ground, splice, terminate and protect underground cable.
Elastimold Innovation
Elastimold’s long, innovative history includes pioneering such products as extended and repair elbows, jacket seal elbows, and shrink-fit joints.
Do công ty LS Cable sản xuất tại Hàn Quốc. Sản phẩm này thuộc nhóm sản phẩm chất lượng cao cấp nhất trên thế giới (dùng lớp cách điện Epoxy theo công nghệ nhúng của Mỹ), và chất lượng ngang hàng với các nhà sản xuất Mỹ / EU. Sản phẩm này cung cấp cho Sân bay Changi Singapore là công trình lớn nhất S.E.A, và công trình Keangnam Landmark Hà nội ( là công trình lớn nhất tại Việt nam). Hiện tại sản phẩm này đang được bán đại trà trên toàn thế giới, và thuộc top 5 nhà sản xuất hàng đầu thế giới. Đây cũng là sản phẩm cao cấp nhất được cung cấp tại Việt Nam với thời gian bảo hành lên đến 2 năm kể từ ngày đóng điện an toàn. Hiện LS Cable đã cung cấp hơn 50 công trình tại VN, trong đó có những công trình tiêu biểu như : Royal City, Time City, Crowne Plaza HN, Petroland Tower HCM, Petrovietnam Power Landmark, Crescent Mall HCM, Bệnh viện Đại Học Y Dược, Bệnh Viện Đa Khoa Hoàn Mỹ, Bệnh Viện Miền Đông, Diamond Island HCM, Kenton Residence HCM, Dargon Hill Residence, Riverside Residence Phú Mỹ Hưng, River Park Phú Mỹ Hưng, Saigon Airport Plaza, Khách sạn Grand, Khách sạn 5 sao Le Meriden, Royal City HN, Sail Tower ….Sản phẩm này cũng chiếm thị phần số 1 tại Singapore hiện nay.
400 Series Interface C Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
RAYCHEM SAUDI ARABIA LTD. (TYCO ELECTRONICS) |AKBAR TRADING EST. SAUDI ARABIA...AKBAR TRADING
te connectivity saudi arabia
TYCO TERMINATION KIT IN ALL VOLTAGE
Raychem terminations for polymeric and MIND
paper insulated cables from 7.2 kV up to 36 kV
System Designer
케이블 종단-거-瑞侃工具包电缆终端-阿克巴交易
ชุด การเลิกจ้าง
RAYCHEM SAUDI ARABIA LTD. (TYCO ELECTRONICS)
11kV-33kV Medium Voltage Heat Shrink Cable Joints & Cable Terminations
11kV and 33kV heat shrink cable joints and cable terminations for medium voltage power cables - SPS heat shrink cable joints and cable terminations are suitable for installation at indoors and outdoors in the Middle East countries, this includes salt laden and dusty atmospheres associated with the Middle East oil, gas and petrochemical industries. Cable terminations and cable joints are suitable for XLPE and paper insulated single core and three 3 core cables of 11kV and 33kV voltages, 3 phase, 50HZ type electrical systems with highest system voltages of 12kV and 36kV. Cable joints are suitable for connecting two XLPE insulated cables of same size or dissimilar sizes and for transition between XLPE and paper insulated lead covered (PILC) medium voltage cables.
Yamuna Infra & Technology Pvt. Ltd. is an India based leading manufacturer and exporter of high-quality heat shrinkable power cable jointing kits, heat shrinkable power cable termination kits and power cable accessories upto 36kV. Established in 1996, we have been supplying many of the leading power and telecom industries all over the world. We manufacture and market our products under 'US-SEAL' brand/trademark, which itself speak about million acknowledgements for their performance. We are one of the leading companies focused on manufacturing high-quality heat shrinkable moulded components such as cable breakout boots, cable end sealing caps and other electric cable accessories.
For more information visit www.yamunainfra.com
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 20S (M20) 1/2" NPT Entry Thread Standard, 3/4" NPT Optional
Cable Gland Suits Cable Diameters 9.5mm-15.9mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Barrier Cable Glands (ATEX Certified) for Hazardous Areas
Zone 1, Zone 2, Zone 21, Zone 22 (Flameproof Exd) Cable Termination
CMP PX2K Triple Certified Flameproof (Type ‘d’), Increased Safety (Type ‘e’) and Restricted Breathing (Type ‘nR’) barrier gland for use in Zone 1, Zone 2, Zone 21 and Zone 22 hazardous areas - suitable with all types of armoured cable providing a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath.
CMP PX2K barrier cable glands are ATEX certified for use with equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound barrier glands for cable terminations within ATEX hazardous areas areas are supplied with a "universal" reversible armour clamp to suit all types of armoured cable termination - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas.
CMP PXSS2K barrier cable glands are Class I Division 2 ABCD approved for use with non-armoured marine and tray cable (type TC) providing a compound barrier seal around the cable conductors and an environmental seal on the cable outer jacket - the PXSS2K barrier glands are IP68 rated.
CMP PX2K and PXSS2K barrier cable glands provide mechanical cable retention - a combined detachable spacer and compound tube allows the cable to be easily disconnected from the equipment for maintenance. This feature also facilitates remote make off procedures when the barrier termination is to be conducted in confined spaces.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 40 (M40) 1.1/4" NPT Entry Thread Standard, 1.1/2" NPT Optional
Cable Gland Suits Cable Diameters 27.9mm-40.4mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 20S/16 (M20) 1/2" NPT Entry Thread Standard, 3/4" NPT Optional
Cable Gland Suits Cable Diameters 6.1mm-11.5mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 20 (M20) 1/2" NPT Entry Thread Standard, 3/4" NPT Optional
Cable Gland Suits Cable Diameters 12.5mm-20.9mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 63 (M63) 2.1/2" NPT Entry Thread Standard, 3" NPT Optional
Cable Gland Suits Cable Diameters 54.6mm-65.9mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 75S (M75) 2.1/2" NPT Entry Thread Standard, 3" NPT Optional
Cable Gland Suits Cable Diameters 59.0mm-72.1mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
Explosion proof barrier glands provide a flameproof compound seal, outer sheath seal and universal armour clamp for steel wire armoured (SWA) and galvanised steel braided (GSWB) cable termination. A barrier gland is an Ex d cable gland incorporating a compound filled chamber sealing around the individual cores of the cable to maintain the flameproof integrity of the electrical equipment. A barrier gland must be used where the standard method of cable glanding (elastomeric seals) an Ex cable entry is considered unlikely to maintain the integrity of flameproof electrical equipment and contain an explosion within the electrical enclosures due either to cable construction or degree of explosion risk.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 90 (M90) 3" NPT Entry Thread Standard, 3.1/2" NPT Optional
Cable Gland Suits Cable Diameters 76.2mm-90.4mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 32 (M32) 1" NPT Entry Thread Standard, 1.1/4" NPT Optional
Cable Gland Suits Cable Diameters 23.7mm-33.9mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 25S (M25) 3/4" NPT Entry Thread Standard, 1" NPT Optional
Cable Gland Suits Cable Diameters 14.0mm-22.0mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
1. Company Profile
Hunan Guanglian Photoelectricity Technologies Co., Ltd(GL Technology) is a leading global
manufacturer of fiber optic cable. GL Technology offers its customers a complete range of outdoor fiber
optic / aerial fiber optic cable / duct fiber optic cable /directly buried fiber optical cable /ADSS,OPGW and
OPPC for power system transmission in China.
GL Technology have over 300 equipment for manufacturing various cables and optical cables and over
100 testing equipment. The production lines include Austria MS Coloring Machines, Color Circling
Machine, Switzerland Swiss Cable Secondary Coating Line, France Delachaux stainless steel tube
welding line, European first-class steel tube laser welding line for submarine and OPGW fiber optical
cables, fluro-plastic high temperature lines of US Davis company, three-layer simultaneously extruded
cross linking lines, CCV Catenary production lines of Troester Company, Germany, GJB-complied military
cable production lines and so on.
Over 200.00km of fiber optic cables installed, with sold over the world more than 30 countries. GL
Technology have been used in various fields over the world. In GL Technology, We supply a full system
and providing fiber optic cable system solutions and technical assistance for you. Customers who choose
the GL Technology can be sure that their decision will lead to a successful experience.
3. Optical Fibers Characteristics
ITU-TG652
Cladding diameter 125±0.7um
Mode field diameter
At 1310nm From 9.2±0.4um
Attenuation
At 1310nm 0.36dB/km max.
At 1550nm 0.22dB/km max.
Chromatic dispersion
At 1310nm 2.8ps/nm.km)
From 1285 to 1330nm 3.5ps/nm.km)
At 1550nm 18ps/nm.km)
From 1525 to 1575nm 20ps/nm.km)
PMD(Polarisation mode dispersion) ≦0.2ps/√km
ITU-T G655
Cladding diameter 125±1.0um
Mode field diameter
At 1550nm From 9.2±10.0um
Attenuation
At 1550nm 0.25dB/km max.
At 1625nm 0.27dB/km max.
Chromatic dispersion
From 1530to 1565nm From 2.0 to 6.15ps/NM.km)
From 1565to 1625nm From 4.5 to 12.4ps/NM.km)
PMD(Polarisation mode dispersion) ≦0.5ps/√km
Noted:: Various kind of Single mode fiber or multimode fiber is available upon customer request.
4. www.gl-fibercable.com1
Typical Designs of Central Stainless Steel Tube OPGW
Description
The central stainless steel tube is surrounded by single or double layers of aluminum clad steel
wires(ACS) or mix ACS wires and aluminum alloy wires. are the most widely used cables ,their design is
fully adapted to the most common electric line needs.
Characteristic:
1. High quality standards for designing, testing and producing with grade A materials available to ensure
long-term reliability .
2. Engineering support supervising and providing its own line of accessories hardware .
3.Seal stainless steel tube superior protection to the fiber optical to moisture and extreme environmental
conditions such as lightening
4. To construct OPGW must cut power, resulting in greater loss, thus OPGW must be used in constructing
high pressure line over 110kv;
5. Apply to the transformation of old lines.
Standards:
ITU-TG.652 Characteristics of a single mode optical fiber
ITU-TG.655 Characteristics of a non-zero dispersion -shifted single mode fibers optical
EIA/TIA598 B Col code of fiber optic cables
IEC 60794-4-10 Aerial optical cables along electrical power lines-family specification for OPGW
IEC 60794-1-2 Optical fiber cables -part test procedures
IEEE1138-2009 IEEE Standard for testing and performance for optical ground wire for use on
electric utility power lines
IEC 61232 Aluminum -Clad steel wire for electrical purposes
IEC60104 Aluminum magnesium silicon alloy wire for overhead line conductors
IEC 61089 Round wire concentric lay overhead electrical stranded conductors .
Aluminum Clad Steel or / Aluminum Alloy Wires
Optical Fiber
Sealed Stainless Steel tube
5. www.gl-fibercable.com2
Typical design for Single Layer:
Specification Fiber Count
Diameter
(mm)
Weight
(kg/km)
RTS(KN) Short Circuit (KA2s)
OPGW-32(40.6;4.7) 12 7.8 243 40.6 4.7
OPGW-42(54.0;8.4) 24 9 313 54 8.4
OPGW-42(43.5;10.6) 24 9 284 43.5 10.6
OPGW-54(55.9;17.5) 36 10.2 394 67.8 13.9
OPGW-61(73.7;175) 48 10.8 438 73.7 17.5
OPGW-61(55.1;24.5) 48 10.8 358 55.1 24.5
OPGW-68(80.8;21.7) 54 11.4 485 80.8 21.7
OPGW-75(54.5;41.7) 60 12 459 63 36.3
OPGW-76(54.5;41.7) 60 12 385 54.5 41.7
Note:
1. Only a part of OPGW cables are listed in the table. Cables with other specifications can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
Typical design for Double Layer:
Specification Fiber Count Diameter(mm)
Weight
(kg/km)
RTS(KN) Short Circuit (KA2s)
OPGW-96[121.7;42.2] 12 13 671 121.7 42.2
OPGW-127[141.0;87.9] 24 15 825 141 87.9
OPGW-127[77.8;128.0] 24 15 547 77.8 128
OPGW-145(121.0;132.2) 28 16 857 121 132.2
OPGW-163(138.2;183.6) 36 17 910 138.2 186.3
OPGW-163(99.9;213.7) 36 17 694 99.9 213.7
OPGW-183(109.7;268.7) 48 18 775 109.7 268.7
OPGW-183(118.4;261.6) 48 18 895 118.4 261.6
Note:
1. Only a part of OPGW cables are listed in the table. Cables with other specifications can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
6. www.gl-fibercable.com3
Typical Designs of Stranded Stainless Steel Tube OPGW
Description:
The stainless steel tube is stranded by double or three layers of aluminum clad steel wires(ACS) or
mix ACS wires and aluminum alloy wires.
Characteristic:
1.High quality standards for designing, testing and producing with grade A materials available to ensure
long-term reliability .
2 Engineering support supervising and providing its own line of accessories hardware .
3.larger tensile strength and fault current capacity to reach a better balance of electrical and mechanical
performance.
Typical design for Double Layer:
Specification
Fiber
Count
Diameter(mm)
Weight
(kg/km)
RTS(KN)
Short Circuit
(KA2s)
OPGW-89[55.4;62.9] 24 12.6 381 55.4 62.9
OPGW-110[90.0;86.9] 24 14 600 90 86.9
OPGW-104[64.6;85.6] 28 13.6 441 64.6 85.6
OPGW-127[79.0;129.5] 36 15 537 79 129.5
OPGW-137[85.0;148.5] 36 15.6 575 85 148.5
OPGW-145[98.6;162.3] 48 16 719 98.6 162.3
Typical design for Three Layer:
Specification
Fiber
Count
Diameter(mm)
Weight
(kg/km)
RTS(KN) Short Circuit (KA2s)
OPGW-232[343.0;191.4] 28 20.15 1696 343 191.4
OPGW-254[116.5;554.6] 36 21 889 116.5 554.6
OPGW-347[366.9;687.7] 48 24.7 2157 366.9 687.7
OPGW-282[358.7;372.1] 96 22.5 1938 358.7 372.1
Noted:The above just the some parts of design more can be produce as required .
Aluminum Clad Steel or / Aluminum Alloy Wires
Aluminum Clad Steel
Optical Fiber
Sealed Stainless Steel tube
7. www.gl-fibercable.com4
Typical Designs of Central AL-covered Stainless Steel Tube OPGW
Description:
The central Al-covered steel tube is surrounded by single or double layers of aluminum clad steel
wires(ACS) or mix ACS wires and aluminum alloy wires. Al-covered Stainless Steel tube design increases
the cross section of AL, to reach a better fault current and lightning resistance performance. Apply to the
transmission line which requires small diameter and large fault current.
Typical Design for Single Layer
Specification
Fiber
Count
Diameter(mm)
Weight
(kg/km)
RTS(KN) Short Circuit(KA2s)
OPGW-80(82.3;46.8) 24 11.9 504 82.3 46.8
OPGW-70(54.0;8.4) 24 11 432 70.1 33.9
OPGW-80(84.6;46.7) 48 12.1 514 84.6 46.7
Typical Design for Double Layer
.
Specification
Fiber
Count
Diameter(mm)
Weight
(kg/km)
RTS(KN) Short Circuit (KA2s)
OPGW-143(87.9;176.9) 36 15.9 617 87.9 176.9
Noted:The above just the some parts of design more can be produce as required.
Aluminum Clad Steel Wires / Aluminum Alloy Wires
AL-Covered SUS Tube
Aluminum Clad Steel Wires / Aluminum Alloy Wires
Stainless Steel tube
Optical Fiber
AL-Covered SUS Tube
8. www.gl-fibercable.com5
Typical Designs of Aluminum Tube OPGW
Description:
The Aluminum tube is surrounded by single or double layers of aluminum clad steel wires(ACS) or mix
ACS wires and aluminum alloy wires.Good anti-corrosion performance.Material and structure are uniform,
good resistance to vibration fatigue
.
Application:
The Aluminum tube is surrounded by single or
double layers of aluminum clad steel wires(ACS) or mix ACS wires and aluminum alloy wires.Good
anti-corrosion performance.Material and structure are uniform, good resistance to vibration fatigue
Characteristic:
1. Good anti-corrosion performance.
2. Material and structure are uniform, good resistance to vibration fatigue.
3. Short circuit current has small effect on the optical fiber transmission properties.
4. Good anti-lightning performance.
Typical Design:
Specification
Fiber
Count
Diameter(mm)
Weight
(kg/km)
RTS(KN) Short Circuit(KA2s)
OPGW-113(87.9;176.9) 48 14.8 600 70.1 33.9
OPGW-70(81;41) 24 12 500 81 41
OPGW-66(79;36) 36 11.8 484 79 36
OPGW-77(72;36) 36 12.7 503 72 67
Note:
1. Only a part of OPGW cables are listed in the table. Cables with other specifications can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
Aluminum Clad Steel Wires / Aluminum Alloy Wires
Optical Fiber
FRP Central member
AL-Covered SUS Tube
PBT Loose Buffer Tube
9. www.gl-fibercable.com6
Typical Designs of OPPC
Description:
The Aluminum tube is surrounded by single or double layers of aluminum clad steel wires(ACS) or mix
ACS wires and aluminum alloy wires Aluminum wires / Aluminum alloy wires Optical fibers.
Aluminum.OPPC cables have the dual functions performance functions of phase
conductors with communication capabilities.
Characteristic:
1. Replacing one or several wires of the traditional conductor with stainless steel tube and strand the tube
with AS/steel wires and AL/AA wires.
2. Replacing one of the three phase conductors with OPPC, thus to form a transmission line which
consists of one OPPC and two phase conductors.
3. OPPC can meet durative high temperature resistant which verified by Temperature Cycling test and
Short Current test.
4. OPPC is applied to middle & high voltage power lines without ground wires such as 10kV, 35kV, 66kV
and so on.
5. Telecommunications for middle & high voltage power lines in urban and rural areas; Providing optical
cables for building distribution automation station.
Typical Design:
Specification
Fiber
Count
Diameter(mm)
Weight
(kg/km)
RTS(KN)
Ampacity
(40℃-70℃)
Ampacity
(40℃-90℃)
Ampacity
(40℃-90℃)
OPPC-240/30 16 21.7 890 76.6 445A 639A 639A
OPPC-70/10 16 17.4 598 52.8 351A 495A 495A
OPPC-120/25 24 15.9 523 49 308 432A 432A
OPPC-150/35 24 17.6 641 64.5 348 492A 492A
Note:
1. Only a part of OPGW cables are listed in the table. Cables with other specifications can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
Optical fibers
Aluminum clad steel wires
Aluminum wires / Aluminum alloy wires
10. www.gl-fibercable.com7
Accessories Hardware
1. Suspension Clamp
Assembly with reinforced suspension clamp and neoprene inner covering ,especially designed for OPGW
cables includes grounding clamps for tower connection .
Suspension clamp(Single) Suspension clamp(Double)
Structure
> straight shackle --( Galvanized forged steel
> Parallel connection clamp ---(Aluminum)
> Armour grid suspension clamp--(Aluminum)
> Preformed rods ---(Aluminum Alloy)
> Grounding clamp ---(Aluminum )
2. Dampers
The dampers are used to absorb the cable vibrations , The number of dampers is determined by the
environmental conditions, the distance between towers, the type of OPGW cable and the installation
parameters
Structure
> Securing clamp (Aluminum alloy )
> Messenger cable --(Galvanized steel wire)
> Counter weights--( Galvanized forged steel)
Vibration damper
11. www.gl-fibercable.com8
Down-lead Clamp
The down-lead clamp clamps are used to fix the cable to the tower in the down lead to the joint box
Structure
1. Clamp--(Aluminum )
2. M-12-rod-(Galvanized steel )
3. Support body --(Galvanized steel )
4. Lock screw---( stainless steel )
Tension Assembly
Preformed tension especially designed for OPGW cable Includes grounding clamps for tower
connection ,when the distance between two anchor towers is greater than maximum length of OPGW
cable drums, there are special tension assemblies for installation in suspension towers,allowing a cable
joint to be included.
Structure
1. Straight shackle -( Galvanized fogged steel)
2. Extension Link( Galvanized laminated steel )
3. Dead end --(Compression aluminum clad steel)
4. Thimble ---(Cast galvanized steel)
5. Protection Splice--(Compression aluminum clad steel)
6. Ground clamp --(Aluminum)
Configuration
There are three types of assemblies for installation in
tension towers :
1) Passing tension assembly : for intermediate towers
2) Splicing tension assembly : for towers with joint boxes
3) Final tension assembly : for final towers
Noted:More Hardware accessories are available on customer’s request.
Dead-end fitting( Single)
Wire Clamp for tower Wire Clamp for pole
12. www.gl-fibercable.com9
All-dielectric Self-supporting Aerial Installation Cable —ADSS
Description:
GL Mini Span ADSS Fiber optic cable is idea for installation in distribution as well as transmission
environments, even when live -line installations are required As its name indicates,there is no support or
messenger wire required,so installation is achieved in a single pass.
Application: Self-support Aerial installation
Characteristic:
1. Suitable for use on distribution and high
voltage transmission lines with mini spans or
self supporting installation for
telecommunication .
2. Track -Resistant outer jacket available for
the high voltage line where space potentials
up to 35kv.
3. Gel-Filled buffer tubes are S-Z stranded
4. Instead of Aramid yarn or glass yarn,there is no
support or messenger wire required. Aramid yarn
is used as the strength member to assure the tensile
and strain Performance
5. For mini span (100-200) the fiber counts
from 4-24 fibers
Typical Technical Parameter:
Span (meter) Weight(kg/km) Diameter(mm) Initial Tension (N)
Unload Load
12fibers
50 110 12.2 892 1479
100 110 12.2 1338 2043
150 110 12.2 2232 3286
200 110 12.2 3280 4800
24fibers
50 115 12.2 904 1486
150 115 12.2 2261 3304
200 115 12.2 3322 4826
Note:
1. Only a part of ADSS cables are listed in the table. More can be produce as required .
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
Out sheath
Kevlar
Water-blocking line
Loose Tube
Optical Fiber
Tube Filling Compound
Central Strength Member
Fillers
13. www.gl-fibercable.com10
Standard All-dielectric Self-supporting Fiber Optic Cable—ADSS
Description:
Aramid yarn is used as the strength member to assure the tensile and strain Performance. Mainly
installed at existing 220kV or lower voltage power lines . Two Jacket and stranded loose tube design .
Characteristic:
1.Two Jacket and stranded loose tube design .
.Stable performance and compatibility with all
common fiber types
2. Instead of Aramid yarn or glass yarn,there is no
support or messenger wire required. Aramid yarn is
used as the strength member to assure the tensile
and strain Performance
3. Mainly installed at existing 220kV or lower
voltage power lines .
Technical Parameter:
Span (meter) Weight(kg/km) Diameter(mm) Initial Tension (N)
Unload Load
8fibers
100 132 12.2 6000 6280
200 134 12.4 6900 71020
300 138 12.6 8200 84520
400 144 13.00 11500 12020
500 148 13.30 12200 12400
600 162 13.60 17500 17852
700 173 13.90 21600 22200
800 178 14.20 24200 24320
12fibers
100 132 12.2 6000 6280
200 134 12.4 6900 71020
300 138 12.6 8200 84520
400 144 13.00 11500 12020
500 148 13.30 12200 12400
600 162 13.60 17500 17852
700 173 13.90 21600 22200
800 178 14.20 24200 24320
Note:
1. Only a part of ADSS cables are listed in the table. ADSS cables with other spans can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
Out sheath
Kevlar
Inner Sheath
Loose Tube
FRP Strength member
Optical Fiber
Water-blocking system
Tube Filling Compound
14. www.gl-fibercable.com11
Tactical Fiber Optic Cable
Description:
The Simplex cable uses single 900µm tight buffered fiber as fiber optic transmission medium, covered
with aramid yarn as strength member, then extruded with thermoplastic polyurethane sheath.
Application :
1. Military communication system
2. Coal, oil, natural gas, geological
exploration
3. Broadcast television, temporary
communication
Temperature Range:
Operating :-20℃ to 60℃
Storage :-20℃ to 60℃
Characteristic:
1. Flexibility ,easy to storage and operation
2. Polyurethane sheath provide Wear resistant, oil resistant, low temperature flexibility
3. Aramid yarn strength with stable tension .
4. High tensile and high pressure to prevent rat bite, cutting, bending.
5. Cable soft, good toughness, installation, maintenance convenient.
Standards
Comply with standard YD/T1258.2-2003 and IEC 60794-2-10/11
Technical Specification
Fiber
counts
Cable
diameter
(mm)
Weight
(kg/km)
Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
2~4 5 10 600 400 200 300 60 30
6~7 5.2 11.5 600 400 200 300 60 30
10~12 6 12.8 600 400 200 300 60 30
Note:
1. Only a part of cables are listed in the table. Cables with other specifications can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
TPU Jacket
Second Coating
Optical Fiber
Tight buffer
Kevlar
15. www.gl-fibercable.com12
Tactical Fiber Optic Cable with Helical Armored
Description:
The Simplex fiber optic cable uses single 900µm tight buffered Tube structure as fiber optic transmission
medium, covered with aramid yarn as strength member, then extruded with thermoplastic polyurethane
sheath.
Application :
1. Military communication system
2. Coal, oil, natural gas, geological exploration
3. Broadcast television, temporary communication
Temperature Range:
Operating :-20℃ to 60℃
Storage :-20℃ to 60℃
Characteristic:
1. Flexibility ,easy to storage and operation.
2. Stainless steel armored protection for fiber.
3. Polyurethane sheath provide Wear resistant, oil resistant, low temperature flexibility
4. Aramid yarn strength with stable tension .
5. High tensile and high pressure to prevent rat bite, cutting, bending.
6. Cable soft, good toughness, installation, maintenance convenient.
Standards:
Comply with standard YD/T1258.3-2003 and IEC 60794-2-10/11
Technical Specification
Fiber
counts
Cable
diameter
(mm)
Weight
(kg/km)
Tensile strength(N) Crush Resistance
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
2~4 5 12 1400 2200 4000 3000 60 30
6~8 7 13.5 1400 2200 4000 3000 60 30
10~12 9 15 1400 2200 4000 3000 60 30
Note:
1. Only a part of cables are listed in the table. Cables with other specifications can be inquired.
2. Cables can be supplied with a range of single mode or multimode fibers.
3. Specially designed Cable structure is available on request.
Kevlar
Helical Metal Tube
Optical Fiber
TPU Jacket
16. www.gl-fibercable.com13
Hybrid Fiber Optic Cable with Steel Tape
Description:
In the hybrid fiber optic cable, single-mode/multimode fibers are positioned in loose tubes, which are
made of high modulus plastics and filled with water-blocking materials. Loose tubes and required
insulated copper wires are stranded around the metallic central strength member into a compact and
circular cable core. For certain high fiber count cables, the strength member would be covered with
polyethylene (PE). The PSP is longitudinally applied around the cable core, before a PE sheath is
extruded over it.
Application:
1. Suitable the filed where needs to transmit light
signal and electric signal.
2.Mobile operators deploying an RRU architecture
to standardize the RRU
Characteristic:
1.The composite cable provides the equipment
electricity and signal transmission, and Improves
central monitoring and maintenance for equipment
power
2.To reduce the coordination and maintenance
of power supply
3.Combines optical fiber (multimode or single mode )
and copper conductor for DC power in a single light
weight aluminum corrugated cable.
Technical Specification
Cable Type
Fiber
counts
Cable
Diameter
(mm)
Weight
(kg/km) Tensile Strength(N)
Crush
Resistance(N/100mm
Long
-Term
Short
-Term
Long
-Term
Short
-Term
GDTS-2~24 2×1.5 2-24 11.2 132 600 1500 300 1000
GDTS-2~24 2×2.5 2-24 12.3 164 600 1500 300 1000
GDTS-2-24 2×4.0 2-24 13.4 212 600 1500 300 1000
GDTS-2~24 2×5.0 2-24 14.6 258 600 1500 300 1000
GDTS-2~24 2×6.0 2-24 15.4 287 600 1500 300 1000
GDTS-2~24 2×8.0 2-24 16.5 350 600 1500 300 1000
Note:
1.2*1.5/2*2.5/2*4.0/2*6.0 is the number of specification of the conductor.
2.Different conductor specification can be make as required.
3.Different Fiber specification can be make as required.
Optical Fiber
PE Sheath
PSP
Loose Tube
Rip Cord
Strength Member
Insulated Conductor
Cable Filling Compound
17. www.gl-fibercable.com14
Submarine optical fiber cable
Description:
Stranded Loose Tube Cable with Aluminum and Steel Tape plus Steel Wire Armor GYTA53+33 or
GYTA53+333. Steel wire used as the central strength member.Special tube filling compound ensure a
critical protection of fiber. Crush resistance and flexibility
Application :
Submarine water and vertical shaft
Characteristic:
1.Excellent mechanical and temperature performance
2.Better tensile strength performance with steel Wires
Technical Specification
Cable
Type
Fiber
Count
Cable Diameter
mm
Cable Weight
Kg/km
Tensile Strength
Long/Short Term N
GYTA53+33 2~36 19.2 580 4000/10000
GYTA53+33 38~60 20.4 650 4000/10000
GYTA53+33 60~72 21.2 670 4000/10000
GYTA53+33 74~96 23.0 780 4000/10000
GYTA53+33 98~120 24.2 840 4000/10000
GYTA53+33 122~140 26.0 950 4000/10000
GYTA53+333 2~36 25.2 1640 20000/40000
GYTA53+333 38~60 26.4 1740 20000/40000
GYTA53+333 60~72 27.0 1780 20000/40000
GYTA53+333 74~96 29.0 1980 20000/40000
GYTA53+333 98~120 30.2 2170 20000/40000
GYTA53+333 122~140 32.2 2300 20000/40000
Optical FIber
Tube Filling Compound
Cable Filling Compound
APL
PE Inner Sheath
Water-blocking Material
PSP
PE Middle Sheath
Strength Member
Steel Wire armored
PE Out sheath
PE Outer Sheath
Steel Wire Armored
PE Middle sheath
PE Inner Sheath
Strength Member
Water-blocking Material
PSP
Optical Fiber
APL
Loose Tube
Tube Filling Compound
Cable Filling CompoundGYTA53+333GYTA53+33
18. www.gl-fibercable.com15
Uni-tube Light-armored Cable (GYXTW)
Description
In the GYXTW cable, single-mode/multimode fibers are positioned in the loose tube, which is made of
high modulus plastic materials and filled with filling compound. PSP is longitudinally applied around the
loose tube, and water-blocking materials are distributed into interstices between them to guarantee the
compactness and longitudinal water-blocking performance. Two parallel steel wires are placed at both
sides of the cable core while PE sheath is extruded over it.
Application : Aerial/ Duct
Temperature Rage:
Storing temperature:-40℃ to +70℃
Operating temperature:-40℃ to +70℃
Characteristics:
●Excellent mechanical and temperature performance
guaranteed by the accurate excess fiber length.
●Critical protection to fibers, based on the excellent
hydrolysis resistance and strength performance of tube material
and special filling compound filled in the tube.
●Special compact structure to avoid the loose tube shrinkage.
●Excellent crush resistance and flexibility.
●PSP enhances the cable crush-resistance, impact-resistance
and moisture-proof.
●Two parallel steel wires ensure tensile strength.
Small diameter, light weight and installation friendliness with
long delivery length.
● Excellent ultraviolet prevention with PE sheath.
● Small diameter, light weight and installation friendliness
Standards
Comply with standard YD/T 769-2010
Technical Parameters
Cable Type
(increased by
2fibers)
Fiber
Count
Cable
Diameter mm
Cable
Weight
kg/km
Tensile Strength
Long/Short Term
N
Crush Resistance
Long/Short Term
N/100mm
Bending Radius
Static/Dynamic
mm
GYXTW 2 ~12 2 ~ 12 8.2 78 600/1500 300/1000 10D/20D
Note:
1. Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Optical Fiber
Tube Filling Compound
Loose Tube
Water-blocking Material
PSP
Steel Wire Strength Member
PE Jacket
19. www.gl-fibercable.com16
Stranded Loose Tube Cable with Aluminum Tape/Steel Tape (GYTA/GYTS)
Description
In the GYTA cable, single-mode/multimode fibers are positioned in the loose tubes, the tubes are filled
with water blocking filling compound.Tubes and fillers are stranded around the strength member into a
circular cable core. An APL/PSP is applied around the core. Which is filled with the filling compound to
protect it. Then the cable is completed with a PE sheath.
Application: Duct/Aerial
Temperature Range:
Storing temperature:-40℃ to +70℃
Operating temperature:-40℃ to +70℃
Characteristics
●Excellent mechanical and temperature
performance guaranteed by the accurate excess Fiber length
●Critical protection to fibers
●The following measures are taken to ensure the
water blocking performance of the cable.
- Single steel wire used as the central strength member
- Special water-blocking filling compound in the loose tube.
- 100% cable core filling
Standards
Comply with standard YD/T 901-2009 as well as IEC 60794-1
Technical Parameters
Cable Type
(increased by
2fibers)
Fiber Count
Tubes+
Fillers
Cable
Diameter
mm
Cable
Weight
kg/km
Tensile
Strength
Long/Short
Term N
Crush
Resistance
Long/Short Term
N/100mm
Bending Radius
Static/Dynamic
mm
GYTA /S2 ~ 30 2 ~ 30 5 9.5 80 600/1500 300/1000 10D/20D
GYTA/S 32 ~ 36 32 ~ 36 6 9.7 97 600/1500 300/1000 10D/20D
GYTA/S 38 ~60 38 ~60 5 10.5 109 600/1500 300/1000 10D/20D
GYTA /S62 ~72 62 ~72 6 11.5 126 600/1500 300/1000 10D/20D
GYTA /S74 ~96 74 ~96 8 13.2 153 600/1500 300/1000 10D/20D
GYTA /S98 ~120 98 ~120 10 14.6 182 600/2000 300/1000 10D/20D
GYTA /S122 ~ 144 122 ~ 144 12 16.5 221 600/2500 300/1000 10D/20D
GYTA/S 146 ~ 216 146 ~ 288 18 16.5 221 600/2500 300/1000 10D/20D
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Fiber
Tube Filling Compound
Loose Tube
Cable Filling Compound
APL/PSP Armored
PE Sheath
Steel Wire Strength Member
20. www.gl-fibercable.com17
Stranded Loose Tube Cable with Aluminum Tape and Steel Tape
(Double Sheaths) (GYTA53)
Description
In the GYTA53 cable, single-mode/multimode fibers are positioned in the loose tubes, the tubes are filled
with water blocking filling compound.Tubes and fillers are stranded around the strength member into a
circular cable core. An Aluminum Polyethylene Laminate(APL) is applied around the core. Which is filled
with the filling compound to protect it. Then the cable is completed with a thin PE sheath. After PSP is
applied over the inner sheath, the cable is completed with a PE outer sheath.
Application: Direct buried
Temperature Range:
Storing temperature:-40℃ to +70℃
Operating temperature:-40℃ to +70℃
Characteristics
●Excellent mechanical and temperature.
●Critical protection to fibers.
●The following measures are taken to ensure the
water blocking performance of the cable:
- Single steel wire used as the central strength Member
- Special water-blocking filling compound in the loose tube
- 100% cable core filling
- APL and PSP moisture barrier
Standards
Comply with stand YD/T 901-2009 as well as IEC 60794-1
Technical Parameters
Cable Type
(increased by
2fibers)
Fiber
Count
Tubes
+Fillers
Cable
Diameter
mm
Cable
Weight
kg/km
Tensile Strength
Long/Short
Term N
Crush
Resistance
Long/Short Term
N/100mm
Bending
Radius
Static/Dynamic
mm
GYTA53 2 ~ 36 2 ~ 36 6 13.7 190 1000/3000 1000/3000 10D/20D
GYTA53 38 ~ 72 38 ~ 72 6 15.3 229 1000/3000 1000/3000 10D/20D
GYTA53 74~96 74~96 8 15.9 244 1000/3000 1000/3000 10D/20D
GYTA53 98 ~120 98 ~120 10 18.0 288 1000/3000 1000/3000 10D/20D
GYTA53 122 ~144 122 ~144 12 19.2 325 1000/3000 1000/3000 10D/20D
GYTA53 146~288 146~288 18 20.9 373 1000/3000 1000/3000 10D/20D
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Tube Filling Compound
Optical Fiber
Loose Tube
Cable Filling Compound
PE Inner Sheath
Water-blocking Tape and APL
PSP Armored
PE Outer sheath
Steel Wire Strength Member
21. www.gl-fibercable.com18
Stranded Loose Tube Cable with Steel Tape (Double Sheaths) (GYTY53)
Description
In the GYTY53 cable, single-mode/multimode fibers are positioned in the loose tubes, the tubes are filled
with water blocking filling compound.Tubes and fillers are stranded around the strength member into a
circular cable core. Then the cable is completed with a PE sheath. Which is filled with the filling compound
to protect it. After PSP is applied over the inner sheath, the cable is completed with a PE outer sheath.
Application: Direct buried
Temperature Range
Storing temperature:-40℃ to +70℃
Operating temperature:-40℃ to +70℃
Characteristics
●Excellent mechanical and temperature
performance guaranteed by the accurate
excess fiber length
●Critical protection to fibers,
●Excellent crush resistance and flexibility
●The following measures are taken to
ensure the water blocking performance of the cable:
- Single steel wire used as the central strength member
- Special water-blocking filling compound in the loose tube.
PSP moisture barrier
- 100% cable core filling and water-blocking material
Standards
Comply with stand YD/T 901-2009 as well as IEC 60794-1
Technical Parameters
Cable Type
(Increased by 2
fibers)
Fiber
Count
Tubes
+
Fillers
Fiber in
Tube
Cable
Diameter
mm
Cable
Weight
kg/km
Tensile Strength
Long/Short Term
N
Crush Resistance
Long/Short Term
N/100mm
GYTY53 2 ~36 2 ~36 6 6 12.6 184 1000/3000 1000/3000
GYTY53 38 ~ 72 38 ~ 72 6 12 14.0 216 1000/3000 1000/3000
GYTY53 74 ~ 96 74 ~ 96 8 12 15.7 260 1000/3000 1000/3000
GYTY53 98 ~ 120 98 ~ 120 10 12 17.4 301 1000/3000 1000/3000
GYTY53 122 ~ 144 122 ~ 144 12 12 19.0 354 1000/3000 1000/3000
GYTY53 144 ~ 288 144 ~ 288 18 12 19.0 350 1000/3000 1000/3000
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Optical Fiber
Tube Filling Compound
Loose Tube
Cable Filling Compound
PE Inner Sheath
Water-blocking Tape
PSP Armored
PE Outer sheath
Steel Wire Strength Member
Fillers
22. www.gl-fibercable.com19
Stranded Loose Tube Cable with Non-metallic Central Strength Member(GYFTY)
Description
In the GYFTY cable, single-mode/multimode fibers are positioned in the loose tubes, while the loose
tubes strand together around non-metallic central strength member (FRP) into a compact and circular
cable core. the strength member would be covered with polyethylene (PE). The water-blocking materials
are distributed into the interstices of the cable core.Then the cable is completed with a PE sheath.
Application: Duct/Aerial
Temperature Range:
Storing temperature:-40℃ to +70℃
Characteristics
●Excellent mechanical and temperature
Performance. Critical protection to fibers.
●Excellent ultraviolet prevention with PE sheath
●Excellent crush resistance and flexibility
●The following measures are taken to ensure the
water blocking performance of the cable:
- FRP used as the central strength member
- Special water-blocking filling compound in the loose tube
- 100% cable core filling
Standards
Comply with stand YD/T 901-2009 as well as IEC 60794-1
Technicial Parameters
Cable Type
(Increased by
2fibers)
Fiber
Count
Tubes Fillers
Cable
Diameter
mm
Cable
Weight
kg/km
Tensile
Strength
Long/Short
Term N
Crush
Resistance
Long/Short
Term N/100mm
Bending
Radius
Static/Dyna
mic mm
GYFTY 2 ~ 6 2 ~ 6 1 6 11.0 97 600/1500 300/1000 10D/20D
GYFTY 8 ~ 12 8 ~ 12 2 5 11.0 97 600/1500 300/1000 10D/20D
GYFTY 14 ~18 14 ~18 3 4 11.0 97 600/1500 300/1000 10D/20D
GYFTY 20 ~ 24 20 ~ 24 4 3 11.0 97 600/1500 300/1000 10D/20D
GYFTY 26 ~ 30 26 ~ 30 5 2 11.0 97 600/1500 300/1000 10D/20D
GYFTY 32 ~ 36 32 ~ 36 6 1 11.0 97 600/1500 300/1000 10D/20D
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Optical Fiber
Tube Filling Compound
Loose Tube
Cable Filling Compound
Water-blocking tape
PE Sheath
Steel Wire Strength Member
Filler
23. www.gl-fibercable.com20
Figure-8 Cable with Steel Tape/Aluminum (GYTC8S/GYTC8A)
Description
In the GYTC8S/GYTC8A cable, single-mode/multimode fibers are positioned in the loose tubes, while the
loose tubes strand together around metallic central strength member into a compact and circular cable
core, and the water-blocking materials are distributed into interstices of it. After a PSP/APL is applied
around the cable core, this part of cable accompanied with the stranded wires as the supporting part are
completed with a PE sheath to be a figure-8 structure.
Application: Self supporting Aerial
Temperature Range
Storing temperature:-40℃ to +70℃
Operating temperature:-40℃ to +70℃
Characteristics
●Excellent mechanical and temperature performance
●Critical protection to fibers,
●The following measures are taken to ensure the
water blocking performance of the cable:
- Single steel wire used as the central strength member
- Special water-blocking filling compound in the loose tube
- 100% cable core filling
Standards
Comply with stand YD/T 901-2009 as well as IEC 60794-1
Technical Parameters
Cable Type
(Increased by 2
fibers)
Fiber Count
Cable
Diameter
mm
Cable
Weight
kg/km
Tensile Strength
Long/Short Term
N
Crush Resistance
Long/Short Term
N/100mm
GYTC8S/A 2 ~ 30 2 ~ 30 9.6 x 21 270.0 3000/8000 300/ 1000
GYTC8S/A 32 ~ 36 32 ~ 36 10.2 x 21.6 285.0 3000/8000 300/ 1000
GYTC8S/A 38 ~ 60 38 ~ 60 11.6 x 23 320.0 3000/8000 300/ 1000
GYTC8S/A 62 ~ 72 62 ~ 72 12 x 23.4 340.0 3000/8000 300/ 1000
GYTC8S/A 74 ~ 96 74 ~ 96 14.2 x 25.6 390.0 3000/8000 300/ 1000
GYTC8S/A 98~ 120 98~ 120 16.0 x 27.4 430.0 3000/8000 300/ 1000
GYTC8S/A 122~ 144 122~ 144 17.7 x 29.1 480.0 3000/8000 300/ 1000
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Messenger Wire
Web
Loose Tube
Optical Fiber
Filling gel
Filling Compound
Steel wire Strength Member
Fillers
PSP or APL armored
PE Sheath
24. www.gl-fibercable.com21
Figure-8 Cable with Steel Tape(GYXTC8S)
Description
In the GYXTC8S cable,single-mode/multimode fibers are positioned in the loose tube, which is made of
high modulus plastic materials and filled with filling compound.PSP is longitudinally applied around the
loose tube, and water-blocking materials are distributed into interstices of it.Then.this part of cable
accompanied with the stranded wires as the supporting part are completed with a PE sheath to be a
figure-8 structure
Application: Self supporting Aerial
Temperature Range
Storing temperature:-40℃ to +70℃
Operating temperature:-40℃ to +70℃
Characteristics
●Being used full section water retardant structure it possesses
good water retardant and dampproof property.
●Special factice is filled into inside of loosing jacket and takes key
protection to optical fiber.
●Vertical wrapped steel strip strengthens resisting lateral
pressure ability
●figure 8 self supporting type structure possesses
high tensile
strength and is convenient for aerial installation and its installation
cost is cheap.
●The service life of the products will be more 30 years.
Standards
Comply with stand YD/T 1155-2001 as well as IEC60794-1.
Technical Parameters
Cable Type
(Increased by 2fibers)
Fiber
Count
Max.Fibers in
Tubes
Cable
Weight
kg/km
Cable
Diameter
mm
Tensile Strength
Long/Short Term
N
Crush Resistance
Long/Short Term
N/100mm
GYXTC8S 2 ~ 8 2 ~ 8 8 117.0 8.1 x 16.9 2000/6000 300/1000
GYXTC8S 10 ~ 12 10 ~ 12 12 121.0 8.3 x 17.0 2000/6000 300/1000
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Messenger Wire
Web
Loose Tube
Optical Fiber
Filling gel
Filling Compound
PSP Armored
PE Sheath
25. www.gl-fibercable.com22
Small Figure 8 Fiber Optic Cable(GYAXTC8Y)
Description
In the small figure 8 cable, this cable consist of the loose tube with single mode or multimode fibers and
steel wire as the messenger wire, which are formed like “Figure 8”. After aramid yarn is applied over the
inner sheath, the cable is completed with a PE outer sheath.
Application:
Self supporting Aeria for FTTH Solution.l
Temperature Range
Storing temperature:-40℃ to +70℃
Operating temperature:-30℃ to +70℃
Characteristics
●Accurate optical fiber excess length ensures good mechanical and
temperature performance.
●High strength loose tube that is hydrolysis resistant and special tube
filling compound ensure a critical protection of
optical fiber.
●Crush resistance and flexibility.
●Figure 8 self supporting type structure possesses high
tensile strength and is convenient for aerial installation and
its installation cost is cheap.
●The service life of the products will be more 30 years.
●Light, flexible, easy for the laying and it is used for
FTTH solution.
Standards
Comply with stand YD/T 1155-2001 as well as IEC60794-1.
Technical Parameters
Cable Type
(Increased by 2fibers)
Fiber
Count
Max.Fiber
s in Tubes
Cable Weight
kg/km
Cable
Diameter mm
Tensile
Strength N
Crush Resistance
N/100mm
GYAXTC8Y2 ~ 12 2 ~ 12 12 47.0 5.4 x 9.5 500 700
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 3000m/reel: other lengths available on request.
Messenger Wire
PE Sheath
Loose Tube
Tube Filling Compound
Optical FIber
Aramid Yarn
26. www.gl-fibercable.com23
Indoor Simplex Fiber Optic Cable(GJFJV-Single fiber)
Description:
The Simplex cable uses single 900µm or 600µm tight buffered fiber as fiber optic transmission medium,
covered with aramid yarn as strength member, then extruded with a PVC sheath. Othersheath materials,
like LSZH and TPU, are available on request
Application :
1. Terminated with various types of connectors
2. As pigtail of communication equipment
3. Suitable for communication equipment served
Temperature Range:
Operating :-20℃ to 60℃
Storage :-20℃ to 60℃
Characteristic:
1. Excellent strippability with tight buffered fiber
2. Excellent flame retardant properties
3. High tensile strength due to aramid strength member
4. Excellent corrosion resistant, waterproof, flame retardant and
5. environmental- friendly properties of the outer sheath
Standards
Comply with standard YD/T1258.2-2003 and IEC 60794-2-10/11
Technical Parameter
Cable
Diamter
(mm)
Tight
Buffer
diameter
(mm)
Weight
(kg/km)
Tensile strength(N) Crush Resistance
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
1.6±0.2 0.6 2.5 100 60 100 500 60 30
1.8±0.2 0.6 3.5 100 60 100 500 60 30
3.0±0.2 0.9 8 100 60 100 500 60 30
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Outer Sheath
Kevlar
Optical Fiber
Tight Buffer
27. www.gl-fibercable.com24
Indoor Zip-cord Interconnect Fiber Optic Cable(GJFJV)
Description:
The zip-cord interconnect cable uses two 900μm or 600μm tight buffered fibers as fiber optic transmission
medium, covered with aramid yarn as strength member, then extruded with a PVC sheath. Other sheath
materials, like LSZH and TPU, are available on request.
Application :
1. Duplex fiber flexible connection jumper or pigtail
2. Indoor riser level and plenum level cabling
3. Instruments communication equipment interconnection
Temperature Range:
Operating :-20℃ to 60℃
Storage :-20℃ to 60℃
Characteristic:
1. Excellent stripability with tight buffered fiber
2. Excellent flame retardant properties
3. High tensile strength due to aramid strength member
4. Excellent corrosion resistant, waterproof, flame retardant and
5. environmental- friendly properties of the outer sheath
Standards:
Comply with standard YD/T1258.3-2003 and IEC 60794-2-10/11
Technical Parameter
Cable
Diamter(mm)
Tight Buffer
diameter
(mm)
Weight
(kg/km)
Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
1.6*3.3 0.6 4.8 150 80 500 100 60 30
1.6*3.7 0.6 0.6 150 80 500 100 60 30
2.0*4.1 0.9 0.9 150 80 500 100 60 30
2.4*5.0 0.9 0.9 150 80 500 100 60 30
2.8*5.8 0.9 0.9 150 80 500 100 60 30
3.0*6.2 0.9 0.9 150 80 500 100 60 30
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Outer Sheath
Kevlar
Optical Fiber
Tight Buffer
28. www.gl-fibercable.com25
Indoor Duplex Flat Fiber Optic Cable(GJFJBV)
Description:
The duplex flat cable uses two 900μm or 600μm tight buffered fibers as fiber optic transmission medium,
covered with Kevlar aramid yarn as strength member while each fibre extruded with a PVC inner sheath,
then extruded with a flat PVC outer sheath. Other sheath materials, like LSZH and TPU, are available on
request.
Application :
1. Duplex optical fiber flexible connection jumper or pigtail
2. Indoor riser level and plenum level cabling
3.Instruments communication
equipment interconnection
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Characteristic:
1. Excellent strippability with tight buffered fiber
2. Excellent flame retardant properties
3. High tensile strength due to aramid strength member
4. Excellent corrosion resistant, waterproof, flame
retardant and environmental- friendly properties of
the outer sheath
Standards:
Comply with standard YD/T1258.3-2003 and IEC 60794-2-10/11
Technical Parameter
Cable
Diameter(mm)
Inner Jacket
diameter(mm)
Weight(kg/km) Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm))
Short-term Long-term Short-term Long-term Static Dynamic
3.0*5.0 1.8 56 300 800 1000 500 60 30
3.2*5.6 2 65 300 800 1000 500 60 30
4.0*7.0 3 88 300 800 1000 500 60 30
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Outer Sheath
Inner Sheath
Kevlar
Tight Buffer Optical Fiber
29. www.gl-fibercable.com26
Indoor Multi Purpose Break-out FIber Optic Cable I(GJBFJV)
Description:
The multi-core branch cable I takes several simplex cables (900μm tight buffered fibre with aramid yarn
strength member) as the sub-units which are stranded around the central strength member to form the
cable core, then extruded with a PVC sheath. Other sheath materials, like TPU or LSZH, are available on
request.
Application :
1. Connection lines between communication equipment
2. Indoor cabling
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Characteristic:
1. Excellent strippability with tight buffered fiber
2. High tensile strength due to aramid strength member
3. Excellent corrosion resistant, waterproof, flame retardant
and environmental- friendly properties of the outer sheath
Standards:
Comply with standard YD/T1258.4-2005 and IEC 60794-2-20/21
Technical Parameter
Fiber
Counts
Cable
Diameter(mm)
Weight Tensile strength(N)
Crush Resistance
(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
4 7.2±0.4 45.5 200 660 1000 300 10D 20D
6 9.0±0.4 63 200 660 1000 300 10D 20D
8 10.0±0.4 84 200 660 1000 300 10D 20D
12 12.5±0.4 148 200 660 1000 300 10D 20D
24 12.5±0.4 202 400 1320 1000 300 10D 20D
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Optical Fiber
Tight buffer
2.0mm or 3.0mm
Subunit
Aramid Yarn
FRP Strength Member
PVC or LSZH Jacket
30. www.gl-fibercable.com27
Indoor Multi Purpose Distribution Fiber Optic Cable I(GJFJV)
Description:
The multi purpose distribution cable uses several 900μm or 600μm tight buffered fibers as fiber optic
transmission medium, covered with aramid yarn as strength member, then extruded with a PVC sheath.
Other sheath materials, like LSZH, PVC and TPU, are available on request.
Application :
1. Multi-core fiber flexible connector
2. Indoor cabling
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Characteristic:
1. Excellent strippability with tight buffered fiber.
2. High tensile strength due to aramid strength member
3. Excellent corrosion resistant, waterproof, flame retardant and
environmental- friendly properties of the outer sheath
Standards:
Comply with standard YD/T1258.4-2005 and IEC 60794-2-20/21
Technical Parameter
Fiber
Counts
Cable
Diamter(mm)
Weight Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
4 5.2±0.4 16.2 130 440 1000 300 60 30
6 5.5±0.4 20 130 440 1000 300 60 30
8 6.2±0.4 26 130 440 1000 300 60 30
12 6.5±0.4 31.5 200 660 1000 300 60 30
24 8.2±0.4 50.5 200 660 1000 300 60 30
36 9.0±0.4 70.5 200 660 1000 300 60 30
48 10.5±0.4 88.5 200 660 1000 300 60 30
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Tight Buffer Optical Fiber
Aramid Yarn
PVC or LSZH Jacket
31. www.gl-fibercable.com28
Indoor Multi Purpose Distribution Fiber Optic CableⅡ(GJPFJV)
Description:
GJPFJV multi purpose distribution cable use 6-fiber sub-units(900μm tight buffer, aramid yarn as strength
member). A fiber reinforced plastic(FRP) locates in the center of core as a non-metallic strength member.
The sub-units are stranded around the cable core. The cable is completed with a LSZH or PVC jacket.
Application :
1. Backbone distribution cable in building
2. Indoor cabling
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Characteristic:
1. Excellent strippability with tight buffered fiber
2. High tensile strength due to aramid strength
member.
3. Excellent corrosion resistant,waterproof,flame
retardant and environmental- friendly properties of
the outer sheath
Standards:
Comply with standard YD/T1258.4-2005 and IEC 60794-2-20/21
Technical Parameter
Fiber
Counts
Cable
Diamter(mm)
Weight Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
24 15.5±0.4 205 1500 500 1500 600 10D 20D
36 17.5±0.4 255 1500 500 1500 600 10D 20D
48 17.5±0.4 255 1500 500 1500 600 10D 20D
72 19.5±0.4 320 1500 500 1500 600 10D 20D
96 22.0±0.4 395 1500 500 1500 600 10D 20D
144 28.0±0.4 579 1500 500 1500 600 10D 20D
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Tight Buffer Cable
Aramid Yarn
FRP Strength Member
Sub-unit Jacket
PVC or LSZH Jacket
32. www.gl-fibercable.com29
Indoor Flat Fiber Ribbon Fiber Optic Cable (GJDFBV)
Description:
GJDFBV flat ribbon cable uses fiber ribbon as optical transmission medium, covered with aramid yarn as
strength member, then extruded with a PVC sheath. Other sheath materials, like LSZH and TPU, are
available on request.
Application :
1. Ribbon fibre flexible connection jumper
2. Various indoor cabling solutions. Especially used in good laying conditions.
3. Interconnection between apparatuses
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Installation: -5℃ to 50℃
Characteristic:
1. Excellent strippability with tight buffered fiber
2. High tensile strength due to aramid strength member
3. Excellent corrosion resistant,waterproof,flame retardant and environmental- friendly properties of the
outer sheath
Standards:
Comply with standard YD/T1258.4-2005 and IEC 60794-2-20/21
Technical Parameter
Fiber
Counts
Cable
Diamter(mm)
Weight
(kg/km)
Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
2 2.5*3.5 7.3 200 80 500 200 30 50
4 2.5*3.5 7.4 200 80 500 200 30 50
6 2.5*4.0 8.2 200 80 500 200 30 50
8 2.5*4.5 9.3 200 80 500 200 30 50
12 2.5*5.0 10 200 80 500 200 30 50
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Optical Fiber
Fiber Ribbon
Aramid Yarn
Jacket
33. www.gl-fibercable.com30
FTTH Bow-type Drop Cable
Description:
The typical bow-type drop optical cable includes central optical fibers with 2 parallel KFRPs or steel wire
as the strength members placed on both sides, a LSZH or PVC sheath is extruded outside.
Application :
1. All types of fiber cables with different structures
2. High performance optical network operating
3. High speed optical routes in buildings (FTTX)
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Characteristic:
1. Simple structure, light weight, high tensile strength
2. Novel groove design, easily strip and splice,simplified installation and maintenance
3. Low smoke, zero halogen and flame retardant sheath,
environment-friendly, good safety
Standards:
Comply with standard YD/T1997-2009
Technical Parameter
Cable
Type
Cable
Diamter(mm)
Weight
(kg/km)
Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
GJXFH-1 2.0*3.0 8 60 30 1000 300 15 30
GJXFH-2 2.0*3.0 8.5 60 30 1000 300 15 30
GJXFH-4 2.0*4.0 10 60 30 1000 300 15 30
GJXH-1 2.0*3.0 9 60 30 1000 300 15 30
GJXH-2 2.0*3.0 9.5 60 30 1000 300 15 30
GJXH-4 2.0*4.0 10 60 30 1000 300 15 30
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Steel wire or FRP
Optical Fiber
Outer Jacket
34. www.gl-fibercable.com31
FTTH Self-supporting Bow-type Drop Cable
Description:
The typical self-supporting bow-type drop fiber optic cable consists of GJXFH/GJXH cable and an
additional strength member (steel wire or stranded steel wire).
Application :
1. All types of fiber cables with different structures
2. High performance optical network operating
3. High speed optical routes in buildings (FTTX)
Temperature Range:
Operating :-20℃ to 60℃
Storage: -20℃ to 60℃
Characteristic:
1. Novel groove design, easily strip and splice, simplified
installation and maintenance, higher tensile strength
2. Suitable as cable extending from outdoor (as aerial cable)
to indoor
3. Low smoke, zero halogen and flame retardant sheath,
environment-friendly, good safety
Standards:
Comply with standard YD/T1997-2009
Technical Parameter:
Cable Type
Cable
Diamter
(mm)
Weight
(kg/km)
Tensile strength(N)
Crush
Resistance(N/100mm)
Minimum bending
radius (mm)
Short-term Long-term Short-term Long-term Static Dynamic
GJXFH-1 2.0*5.0 21 60 30 1000 300 15 30
GJXFH-2 2.0*5.0 21 60 30 1000 300 15 30
GJXFH-4 2.0*5.6 21.5 60 30 1000 300 15 30
GJXH-1 2.0*5.0 21 60 30 1000 300 15 30
GJXH-2 2.0*5.0 21 60 30 1000 300 15 30
GJXH-4 2.0*5.6 21.5 60 30 1000 300 15 30
Note:
1.Cables can be supplied with a range of single mode or multimode fibers.
2. The dimensions and raw materials can be designed according to the demand of the customers.
3. Standard Reel Length: 2000m/reel: other lengths available on request.
Messenger Wire
FRP or Steel Wire
Optical Fiber
Outer Jacket
35. www.gl-fibercable.com32
Standard Optical Fiber Patch Cord
Description:
A patch cord is optical cable used to connect ("patch-in") one electronic or optical device to another for
signal routing.
Applications
1. Gigabit Ethernet
2. Telecommunication Networks
3. Active Device Termination
4. Video, Industrial, Multimedia,Military
5. Premise Installations
Characteristics:
1. Simplex and duplex connector available
2. High precision of mechanical dimensions.
3. Good exchange ability and good durability;
4. Low Insertion Loss, High temperature Stability and Good exchangeability.
5 Fan-out Available, Pigtail Available, Various
Boot(cable) Size Available
Specification
Single Mode Multimode
Insertion Loss ≤0.2dB
Return Loss ≥50dB(PC); ≥65dB(APC)
Repeat-ability ≤0.1
Durability ≤0.2dB typical change 1000matings
Interchangeability ≤0.2dB
Operating Temperature - 40℃ to +85℃ - 40℃ to +85℃
Ordering Options
Connector SC, FC, ST, LC, E2000, DIN, MU,MTRJ, etc.
Finish UPC, APC,PC; for MTRJ, Female, Male
Cable Type Simplex, Duplex Straight, Duplex Reverse
Fiber SM(G652), 62.5/125um, 50/125um, OM2, OM3,SM(G655)
Cable Jacket Riser, Plenum, LSZH
Cable Diameter Ø3.0mm, Ø2.0mm, Ø0.9mm, etc.
Cable Length Length in meter
Noted: Specially design is acceptable upon customer request.
36. Sales Contact (Tim Tan)
Tel : +86 731 85501765
Fax: +86 731 89722708
E-mail: timoptic@gyt888.com
Skype: opticfiber.tim
Twitter: @opticfiber_tim
Website: www.gl-fibercable.com
Head office:
No.318, Wanjiali Road, Yuhua District, Changsha, Hunan, P.R.China, 410007
Facilities address in Jiangsu:
No.139,Xindong Road,Yangxiang town,Yixing,Jiangsu, P.R.China.214254
Facilities address in Wuhan:
Road Shenglong,Economic and technological development zone.Wuhan, P.R.China.
430056