CMP PX2K Cable Glands (Barrier Glands Exd Flameproof with ATEX Certification for Hazardous Areas)
Cable Gland Size 63 (M63) 2.1/2" NPT Entry Thread Standard, 3" NPT Optional
Cable Gland Suits Cable Diameters 54.6mm-65.9mm
CMP PX2K barrier cable glands are ATEX certified and suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2, Zone 21 and Zone 22. Flameproof compound filled barrier glands for cable terminations within ATEX areas are supplied with a "universal" reversible armour ring to suit all types of armoured cables - this includes steel wire armoured (SWA), steel tape armoured (STA) and wire braided cables for installation within hazardous areas. Barrier cable glands provide a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath. The CMP PX2K cable gland provides a mechanical cable retention and electrical continuity via the cable armour termination. A combined detachable armour cone and compound tube, together with AnyWay universal cable clamping ring arrangement allows the cable to be easily disconnected from the electrical equipment and easily re-connected. This cable gland feature facilitates remote make off procedures when the cable termination is to be conducted in confined spaces or in areas of restricted access.
Cable Glands are suitable for following cable types - Wire Braid Armour, Single Steel Wire Armour (SWA), Screened Flexible Wire Braid (eg CY or SY), Steel Tape Armour (STA), Pliable Wire Armour (PWA)
Cable Sealing Area - Inner Compound Barrier and Cable Outer Sheath
CMP PX2K cable glands with offshore and marine approvals including Lloyds, DNV and ABS are available - LSF cable gland shrouds available for low smoke and fume cable terminations.
1. CABLE GLAND AND CABLE CONNECTION SPECIALISTS
CMP
CMP HAZARDOUS AREA PRODUCTS
The CMP PX2K cable gland is suitable for use with all forms of equipment protection permitted in Zone 1, Zone 2,
Zone 21 & Zone 22 provided always that the prevailing code of practice for selection and installation is observed, e.g.
IEC 60079-14.
The PX2K is supplied in kit form inclusive of two detachable armour cones. Stepped Cone is suitable for SWA cables,
Grooved Cone is suitable for all other approved armoured cables.
C
TECHNICAL DATA
A
PX2K
BS 6121:Part 1:1989, EN 50262:1999
SIRA06ATEX1097X
Code of Protection Category
II 2 GD Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66 - Equipment
ATEX
Zone 1, Zone 2, Zone 21, & Zone 22 - Gas Groups IIA, IIB, IIC
Cable Type
Armour Clamping
Sealing Technique
Sealing Area(s)
Optional Accessories
Cable Gland Selection Table
Available Entry Threads ‘C’
Cable
Gland
Size
Standard
Option
Metric
20S/16
20S
20
25S
25
32
40
50S
50
63S
63
75S
75
90
NPT
NPT
M20
M20
M20
M25
M25
M32
M40
M50
M50
M63
M63
M75
M75
M90
1/2”
1/2”
1/2”
3/4”
3/4”
1”
1-1/4”
1-1/2”
2”
2”
2-1/2”
2-1/2”
3”
3”
3/4”
3/4”
3/4”
1”
1”
1-1/4”
1-1/2”
2”
2-1/2”
2-1/2”
3”
3”
3-1/2”
3-1/2”
F
B
D
05
U
GOST R Certificate Number
Code of Protection Category
Compliance Standards
GGTN Permit Number
GOST K Certificate Number
RoK Permit for Use Number
Lloyds Approval Number
DNV Approval Number
ABS Approval Number
Continuous Operating Temperature
Ingress Protection Rating
Ingress Protection Document
Deluge Protection Compliance
Deluge Protection Document
Cable Gland Material
Seal Material
U
Compliance Standards
E
LL
IECEx Approval Number
Code of Protection Category
EN 60079-0:2004, EN 60079-1:2004, EN 60079-7:2003, EN 60079-15:2003,
EN 61241-0:2004, EN 61241-1:2004
IECEx SIR 06.0044X
Ex d IIC, Ex e II, Ex nR II, Ex tD A21 IP66
IEC 60079-0:2004, IEC 60079-1:2003, IEC 60079-7:2001,
IEC 60079-15:2005, IEC 61241-0:2004, IEC 61241-1:2004
POCC GB.
05.B01912
Ex d IIC U, Ex e II U
OCT P 52350.0-2005, OCT P 52350.1-2005, OCT P 52350.7-2005
PPC 00-18262
KZ7500052.05.01.00063
08-067693
01/00172
E-6157
01-LD 234401-PDA
-60°C to +100°C
IP66, IP67, IP68
5046 C549G
DTS01 : 91
5046 C549G-D
Brass, Electroless Nickelplated Brass, Stainless Steel, Aluminium
CMP SOLO LSF Thermoplastic Elastomer / Epoxy Resin Barrier Compound
Wire Braid Armour, Single Wire Armour (SWA), Screened Flexible Wire Braid
(e.g. CY / SY), Steel Tape Armour (STA) Pliable Wire Armour (PWA)
Detachable Compound Tube / Cone & AnyWay Universal Clamping Ring
Unique CMP "LRS" ™ Outer Seal (Load Retention Seal)
Inner Compound Barrier & Cable Outer Sheath
Locknut, Shroud, Entry Thread Seal, Serrated Washer, Earth Tag,
Adaptor/Reducer
L
Compliance Standards
L
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK
Type
Design Specification
ATEX Cetification
L
THORNE & DERRICK UK
CMP Type PX2K Triple Certified Flameproof (Type ‘d’), Increased Safety (Type ‘e’) and Restricted Breathing (Type ‘nR’)
cable gland for use in Zone 1, Zone 2, Zone 21 and Zone 22 Hazardous Areas with all types of armoured cable
providing a compound barrier seal around the cable conductors and an environmental seal on the cable outer sheath.
The cable gland provides mechanical cable retention and electrical continuity via armour termination. A combined
detachable armour cone and compound tube, together with AnyWay universal clamping ring arrangement allows the
cable to be easily disconnected from the equipment, for maintenance and change out etc., and re-connected with the
same consummate ease. This feature also facilitates remote make off procedures when the termination is to be
conducted in confined spaces or in areas of restricted access.
LL
WWW.CABLEJOINTS.CO.UK
PX2K Flameproof Ex d, Increased Safety Ex e, Restricted
Breathing Ex nR Compound Barrier Cable Gland
PX2K CABLE GLAND
Note: Dedicated version for Steel Wire Armour type is PX2KW.
Dedicated version for all other Armour types is PX2KX
Note: This standard design concept is also available with
bi-code approvals, suitable for installation in systems
complying with NEC wiring code rules.
Armour Range †
Diameter Number Overall
Ordering
Cable
Across Across Nominal
Over
Cable
PVC
Minimum
of
Gland
Flats Corners Protrusion Reference
Conductors
Diameter Grooved Stepped
Thread
Shroud
Cores
‘D’
Cone
Cone
Weight
Length (Brass Metric)
‘A’
‘B’
‘D’
Length ‘E’
Reference*
(Kgs)
‘F’
#
Max
Max Min Max Min Max Min Max Max
Max
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
12.6
12.6
12.6
17.5
17.5
23.6
30.0
36.6
41.0
47.9
53.7
59.8
64.3
75.3
15
15
15
29
29
51
80
122
149
205
259
320
364
500
6.1
9.5
12.5
14.0
18.2
23.7
27.9
35.2
40.4
45.6
54.6
59.0
66.7
76.2
11.5
15.9
20.9
22.0
26.2
33.9
40.4
46.7
53.1
59.4
65.9
72.1
78.5
90.4
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
1.0 0.9 1.25 24.0
1.0 0.9 1.25 24.0
1.0 0.9 1.25 30.5
1.0 1.25 1.6 37.5
1.0 1.25 1.6 37.5
1.0 1.6 2.0 46.0
1.0 1.6 2.0 55.0
1.0 2.0 2.5 60.0
1.0 2.0 2.5 70.0
1.0 2.0 2.5 75.0
1.0 2.0 2.5 80.0
1.0 2.0 2.5 89.0
1.0 2.0 2.5 99.0
1.6 3.15 3.15 114.0
26.6
26.6
33.3
40.5
40.5
51.0
61.0
66.5
78.6
83.2
89.0
101.6
111.1
128.6
58.5
58.5
60.5
67.5
67.5
69.5
78.0
75.5
80.5
91.5
92.0
99.0
102.0
120.0
20S16PX2K1RA
20SPX2K1RA
20PX2K1RA
25SPX2K1RA
25PX2K1RA
32PX2K1RA
40PX2K1RA
50SPX2K1RA
50PX2K1RA
63SPX2K1RA
63PX2K1RA
75SPX2K1RA
75PX2K1RA
90PX2K1RA
PVC04
PVC04
PVC06
PVC09
PVC09
PVC11
PVC15
PVC18
PVC21
PVC23
PVC25
PVC28
PVC30
PVC32
0.200
0.200
0.230
0.330
0.330
0.510
0.720
0.825
0.860
1.450
1.600
2.300
3.050
5.000
All dimensions in millimetres
Note: *LSF Shrouds also available on request. †Alternative armour clamping range available for non-standard armour sizes. Marine approvals including Lloyds, DNV & ABS are also available from CMP Products.
# Other thread forms are available
131
www.cmp-products.com