2. With over 13,000 MW of combustion turbine generation
experience, you can say we get fired up over power.
13,000+ MW
3. Your gas
turbines drive
your business
We believe your gas turbine projects should serve your business objectives from
the even before they’re activated. We structure our design and delivery services
to ensure our gas turbine systems are designed for the project’s requirements,
and to suit your business needs throughout their development.
With over 13,000 MW of gas turbine experience, we’ve provided EPCM services
for gas turbine projects up to over 1,000 MW in size, supplying industrial plant
station service loads, peaking and base load power applications, utility power
sales, and provided process steam. Our experience ranges from major capital
projects to small equipment installations, providing controls upgrades, gas fired
systems, and steam turbine generators.
Our flexibility means we can tailor the project’s delivery to best suit your needs.
Our experience delivering projects in a variety of execution approaches means
we can help you determine the best delivery method for your project.
4. Project Development
• Site selection and permitting
• Environmental site assessment
• Environmental and
regulatory approvals
• Air quality management
and modeling
• Greenhouse gas management
• Hazard identification
• Energy audits
• Feasibility studies
• Risk assessment
• Modeling
• Risk analysis
• Life cycle analysis
• Emissions inventory
• Conceptual feasibility studies
Services to develop
your assets, and
advance your business
From initial planning and feasibility studies through to
final commissioning and turn-over, we develop more
than a project, we develop your business assets.
Detailed Engineering
and Design
• Civil/structural
• Mechanical
• Geotechnical
• Piping
• Electrical
• Instrumentation and controls
• Process
• Water treatment and waste system
design including zero wastewater
system design
• Procurement
Project and
Construction
Management
• Scheduling
• Cost Controls
Start-up, Commissioning,
and Testing
• System turnover and
checkout functions
• Equipment, system, and plant testing
Asset Management
• Repowering
• Retrofitting
• Decommissioning
5.
6. El Furrial Power Plant
Monagas, Venezuela
We provided engineering and construction management
services for the 240 MW simple-cycle El Furrial Power Plant.
The facility consists of four Phase III Rolls Royce Trent 60
Combustion Turbine Generators capable of operation on natural
gas, evaporator cooling, a gas compression system, and a water
injection system. Our work on the El Furrial plant required
we provide the engineering and design for the installation of
the turbines as well as balance of plant equipment including
evaporative cooling of the turbine inlet air, balance of plant
equipment, and the engineering and design of a supporting
115kV substation. We were also involved in the project’s
construction, providing construction management services.
Client: Pro Energy
Olinda Landfill Gas to Energy
Olinda, California
We were involved with the 32 MW combined cycle Olinda
Landfill Gas to Energy Project from its design and permitting
through start-up and commissioning.
Once conditioned, the landfill gas is distributed to the four
on-site Solar Taurus combustion gas turbine generators,
heat recovery steam generators, and a single steam turbine
generator. All of the major equipment components were
manufactured in the United States, including the four
combustion turbine generators.
The project received funding by the U.S. Department of
Energy’s Industrial Technologies Program (ITP). Our scope of
work for this project included onsite and offsite civil engineer
design, environmental permitting support, detail engineering
and design services, construction permitting, and start-up and
commissioning of the power plant.
Client: DCO Energy
Eastex Cogeneration Plant
Lonview, Texas
We were actively involved throughout the development of
this 430 MW combined cycle cogeneration facility. We first
acted as the Owner’s Engineer on the project, which utilizes
two GE Frame 7FA combustion turbines, each exhausting
into an off gas duct fired heat recovery steam generator
and supplying steam to a condensing extraction steam
turbine. The facility supplies electrical power to Eastman
Dispatchers, and both high and intermediate pressure
steam to Eastman Chemical Company.
We also provided post construction engineering services,
during start-up and operation, including:
• Pipe Stress Analysis
• Heat Balances
• Piping Modifications
• DCS & Controls
• HP Pressure Reduction Stations
• Water Treatment System Analysis
Client: CSW Energy Inc.
With over 6,500 MW of repowering
experience, we know how to develop
your asset’s potential
6,500+ MW
7.
8.
9. Riverbay Cogeneration
Bronx, New York
We provided engineering and design, and procurement
support for this 40 MW repowering of the existing Riverbay
thermal facility. Two Siemens combustion turbines coupled
to once through steam generators, a Siemens steam turbine
generator, and HP packaged boiler supply process steam
to the Riverbay facility. We provided our engineering and
design services to Fresh Meadow Mechanical Corporation
of Queens, NY, the EPC Contractor.
Client: Fresh Meadow Mechanical Corp.
L’Energia Energy Center
Lowell, Massachusetts
We provided engineering, design, and project management
and procurement services for the repowering of the L’Energia
Energy Center 80 MW capacity combined cycle power plant.
Repowering of the facility required the installation of a new
Rolls Royce Trent 60 dual fuel WLE generator set to replace
the existing Siemens V64.3 combustion turbine generator, and
modifying the existing Deltak HRSG to improve performance
and add an SCR and CO catalyst to reduce emissions.
Our work also involved the installation of an inlet air absorption
chiller, packaged cooling tower, water pumps, balance of plant
control system upgrade, gas compressor and other necessary
equipment and auxiliaries, including:
• DCS upgrade
• Fuel Gas compressors and FG system design
• Building addition and retrofit
• Cable bus
• Switchgear/MCC evaluation and addition
• Station Service Transformer
• CEMS upgrade
• STG Controls
Client: Montgomery L’Energia Power LLC
Hunlock Power Station
Repowering Project
Hunlock Creek, Pennsylvania
Our services ranged from conceptual design through
commissioning of this conversion of the former 45 MW
coal-fired power plant to a clean-burning, efficient natural
gas combined cycle power plant with 125 MW of capacity. We
provided engineering and design, procurement support, and
construction management services for the project, keeping
the project contained within the plant’s original footprint
Details of the project include:
• Two new dual fuel General Electric LM6000 combustion
turbine generators
• Two heat recovery steam generators
• Existing 44 MW steam turbine generator
• Existing condenser
• Auxiliary boiler
• Mechanical chiller system
Client: UGI Development Company
10. Valleyview Cogeneration
Valleyview, Alberta
We provided engineering, procurement, and construction
management services for the installation of a 1 x 45 MW
LM-6000 PC, sprint gas turbines with provision for future
conversion to combined cycle operation, and synchronous
condenser. These units contained water injection for power
augmentation and NOx control. The scope of work included
conceptual engineering, permit application support,
regulatory approvals, detailed and construction engineering,
and commissioning.
Client: ATCO
Rathdrum Power Project
Rathdrum, Idaho
We provided engineering and design, procurement,
assistance, and startup support for this 270 MW natural
gas fired combined cycle power plant.
The 1x1 configured indoor facility is water cooled using a
multi-cell cooling tower. Our design of this plant included
major power equipment consisting of:
• One GE 7FA combustion turbine
• A three pressure heat recovery steam generator with
a selective catalytic reduction system and carbon
monoxide catalyst
• One GE reheat, condensing steam turbine
In addition, the design included a two staged cooling, zero
discharge system for the on-site disposal of all process
wastewater, and a 230 kV switchyard.
Client: Cogentrix /Avista
Pasco Cogeneration
Optimization Study
Dade City, Florida
We executed a performance optimization study to prepare the
Pasco Cogeneration Facility for operation under the plant’s
new Power Purchase Agreement.
This natural gas fired combined cycle cogeneration
plant was designed to deliver process steam and power.
The facility consists of two General Electric LM6000
combustion turbines with water injection, each with a heat
recovery steam generator. Steam is fed to a nominal 26.5
MW condensing steam turbine generator.
The facility was originally designed for base loaded
operation and up to 200,000 lb/hr of export steam.
Currently, the facility operates with daily cycling and will no
longer have an export steam host.
The main goals of this study were to maximize output,
optimize heat rate and ensure that the facility can start up
within the time constraints established in the PPA.
Our services included:
• Heat Rate optimization
• Long term cycling and increased cold start effects on all
plant equipment and systems
• Steam usage optimization
• Identified opportunities to reduce operator interfaces
• Operational concerns for the dump condenser
• Circulating Water System efficiency and tube
failure concerns
• Zero Water Discharge system efficiency
and solids concerns
Client: Pasco Cogeneration LTD.
11.
12. Design with community in mind
We’re active members of the communities we serve. That’s why at Stantec, we always
design with community in mind.
The Stantec community unites more than 13,000 employees working in over 200 locations.
We collaborate across disciplines and industries to bring buildings, energy and resource, and
infrastructure projects to life. Our work—professional consulting in planning, engineering,
architecture, interior design, landscape architecture, surveying, environmental sciences,
project management, and project economics—begins at the intersection of community,
creativity, and client relationships.
Since 1954, our local strength, knowledge, and relationships, coupled with our world-class
expertise, have allowed us to go anywhere to meet our clients’ needs in more creative and
personalized ways. With a long-term commitment to the people and places we serve, Stantec
has the unique ability to connect to projects on a personal level and advance the quality of life
in communities across the globe. Stantec trades on the TSX and the NYSE under the symbol STN.
first.last@stantec.com
(999) 999-9999
Location
Position/Title
Name
