fuel-consumption-measurement-system.pptx
•Download as PPTX, PDF•
0 likes•81 views
Fuel Consumption measurement System(FCS) is a self-contained SKID housing Fuel Tank, Tank Weighing System (TWS) of Mettler Toledo (Model No. IND 570), Fuel Tank Filling Pumps/Flame Proof Motor, Temperature Sensors (RTD), Shell & Tube Type Heat Exchangers for cooling of Fuel and a Control Panel (CP) for user to interact with the system. All electronic/software controls & communication interaction with the FCS SKID is through this CP.
Report
Share
Report
Share
Recommended
DAQ System For Filter.pptx
This PC based Data Acquisition & Control Software is meant for conducting collapse test of Test Filter. It provides the facility to monitor the input/ output parameters such as Differential Pressure, Flow Rate etc. The solution involves a Data Acquisition, Feedback & Control system that interfaces with Pressure, Temperature, Flow Sensors, Solenoid Valves, Level Sensors & the AC drive.
ABC of BMS.pdf
Basic concepts of Building Management Systems, HVAC control Systems, Building Automation System
Test Rig for 130LPM Pump of LCA- Neometrix
The Test Rig is self-contained, Electro Hydraulic Test Rig. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump. The brief spec and tests of this pump is given below as:
The brief specs of the pump-
Rated Pressure = 270 bars
Rated Flow = 130 LPM at 270 bar
Rated Speed = 6000 RPM
Application
The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump.
Key features
Drive System with Gear Box Lube Oil System
High Pressure System for Pressure Proof Testing
Low Pressure System for Functional Test
Control and Indicator Panel
Data Acquisition System.
The test rig is design to work up to 120°C.
Two moog make servo valves have been provided in Rig for Cyclic Test.
Cooling System: We are using water as the medium for the cooling purpose, with the help of Heat Exchanger. Total three heat exchanger has been provided in system.
Filtration: Proper filtration has been provided and the filters have electronic clogging indicators.
The rig is developed for Hydraulic Oil (MIL-H- 5606E) or equivalent.
Three SS 304 Reservoirs of oil capacity 90, 225 and 50 liters have been provided with all related fittings.
Safety Interlocks
The Pump will not start in case the Reservoir oil level is low/ high.
The Pump will stop/ will not start, in case the oil temperature goes beyond a set limit.
There would be alarm and indication, in case any abnormality happens.
In case any of the filters are clogged, there would be alarm; Indication and the Test rig will stop.
It is also independent of the Computer automation system.
Computer: The Rig Diagnostics/ Monitoring & Recording are implemented Through the National Instruments data acquisition System and PC. The customized Software is implemented in Lab View.
Recirculating-Chiller
Recirculating Chiller is high performance circulating water pump with 0 to 1.5 bar pump capacity pressure. Its
temperature ranges from 5˚C to 40˚C and offers PT100 temperature sensor. Designed with TECUMSEH compressor in order
to ensure cooling efficiency and reduce noise with PID temperature controlling technology. Equipped with
Over-temperature protection, auto-alarm function and Color LCD screen display for more running data and dynamic
identifier.
Recommended
DAQ System For Filter.pptx
This PC based Data Acquisition & Control Software is meant for conducting collapse test of Test Filter. It provides the facility to monitor the input/ output parameters such as Differential Pressure, Flow Rate etc. The solution involves a Data Acquisition, Feedback & Control system that interfaces with Pressure, Temperature, Flow Sensors, Solenoid Valves, Level Sensors & the AC drive.
ABC of BMS.pdf
Basic concepts of Building Management Systems, HVAC control Systems, Building Automation System
Test Rig for 130LPM Pump of LCA- Neometrix
The Test Rig is self-contained, Electro Hydraulic Test Rig. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump. The brief spec and tests of this pump is given below as:
The brief specs of the pump-
Rated Pressure = 270 bars
Rated Flow = 130 LPM at 270 bar
Rated Speed = 6000 RPM
Application
The Test Rig provided has been designed to address all the requirements testing of 130 LPM Pump.
Key features
Drive System with Gear Box Lube Oil System
High Pressure System for Pressure Proof Testing
Low Pressure System for Functional Test
Control and Indicator Panel
Data Acquisition System.
The test rig is design to work up to 120°C.
Two moog make servo valves have been provided in Rig for Cyclic Test.
Cooling System: We are using water as the medium for the cooling purpose, with the help of Heat Exchanger. Total three heat exchanger has been provided in system.
Filtration: Proper filtration has been provided and the filters have electronic clogging indicators.
The rig is developed for Hydraulic Oil (MIL-H- 5606E) or equivalent.
Three SS 304 Reservoirs of oil capacity 90, 225 and 50 liters have been provided with all related fittings.
Safety Interlocks
The Pump will not start in case the Reservoir oil level is low/ high.
The Pump will stop/ will not start, in case the oil temperature goes beyond a set limit.
There would be alarm and indication, in case any abnormality happens.
In case any of the filters are clogged, there would be alarm; Indication and the Test rig will stop.
It is also independent of the Computer automation system.
Computer: The Rig Diagnostics/ Monitoring & Recording are implemented Through the National Instruments data acquisition System and PC. The customized Software is implemented in Lab View.
Recirculating-Chiller
Recirculating Chiller is high performance circulating water pump with 0 to 1.5 bar pump capacity pressure. Its
temperature ranges from 5˚C to 40˚C and offers PT100 temperature sensor. Designed with TECUMSEH compressor in order
to ensure cooling efficiency and reduce noise with PID temperature controlling technology. Equipped with
Over-temperature protection, auto-alarm function and Color LCD screen display for more running data and dynamic
identifier.
Continuous boiling point distillation analyser
The ATAC Boilar continuously measures the percent recovered temperatures of petroleum products from 5% to 95% within the distillation temperature range 50°C to 400°C. The Boilar provides fast, continuous, reliable data and is simple to operate and easy to maintain.
Toshniwal - Thermal mass flow meters and controller
THERMAL MASS FLOW METERS AND CONTROLLER
The range of Thermal Mass Flow Meters from Bronkhorst address high accuracy in low flow rate scenarios like those seen in laboratory and Pilot plant usages. With a housing designed for laboratory and clean processing conditions, the instruments are truly unique in their capability to measure and control flow ranges between 0,014…0,7 mln/min and 8…1670 ln/min with pressure rating between vacuum and 400 bar – all in one range of instruments.
FEATURES
Rangeability in digital mode up to 1:150
High accuracy (standard 0,5% Rd plus 0,1% FS)
Pressure ratings 64 / 100 bar
Highly resistant to mechanical shocks and pressure fluctuations
Large range of Input/output options to choose from
Extremely fast and dynamic response
User configurable control characteristics
Applications
Analytical/environmental equipment
Gas flow monitoring in food, chemical and petrochemical industries
Gas consumption measurement in gas distribution systems for internal accounting purposes
Detection of gas leakage through objects
Semiconductor manufacturing
Surface treatment installations
Process Control Fundamentals and How to read P&IDs
Types of Process Control, Feedback control, feed-forward control loops, ratio control loop, split range control. How to read Piping and Instrumentation Diagram for Process Engineers
Instrumentation and process control fundamentals
Basic course covers:
-Basic understanding of process control
-Important process control terminology
-Major components of a process loop
-Instrumentation P&ID symbols
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
RUGGED MONITORING’s R501 is the most versatile and advanced multi-channel monitoring solution. Designed to seamlessly integrate into diverse industries, the R501 stands as a testament to our commitment to innovation and reliability in electrical asset monitoring.
HVAC, Heating Ventilation Air Conditioning BMS
The main purpose of HVAC is to provide the people working inside the building with “CONDITIONED AIR” so that they will have a comfortable and safe work environment.
A BMS system collects the operating information required for intelligent building management.
It analyses the operation of the building systems by viewing all important temperatures, humidities and equipment status.
To:
Ensures energy savings
Improves building operations
Improves building operations allowing remote control/over-ride where necessary
Improves building management by means reporting and traceability
Improves building management by means reporting and traceability
Improves building management by having a faster reaction time to problems
Digital Temperature Controllers
The materials included in this compilation are for the use of Dwyer Instruments, Inc. potential customers and current employees as a resource only. They may not be reproduced, published, or transmitted electronically for commercial purposes. Furthermore, the Company’s name, likeness, product names, and logos, included within these compilations may not be used without specific, written prior permission from Dwyer Instruments, Inc. ©Copyright 2014 Dwyer Instruments, Inc.
Siemens Terminal Box Controller (APOGEE Automation System )
In This PPT we are discussed about complete details of that product (Use,Operation, Technical details, Dimensions, Wiring, and etc..)
Please Support us and Follow our other Sites
https://www.instagram.com/controlsandsystems.offical
https://twitter.com/ControlsSystems
https://automationtechplc2.blogspot.com
https://humidificationcontrol.blogspot.com
https://controlsandsystems.business.site
www.controls.systemsdm@gmail.com
If you enjoyed this article, share it with your friends and colleagues
Emergency Shutdown System, ESD System - Worldwide Oilfield Machine
WOM’s Emergency Shutdown System (ESD) provides a fast acting functional safety shutdown in case of a hydrocarbon escape or other safety issues.
Advanced Control Systems - Worldwide Oilfield Machine
WOM's Advanced Control System software is equipped with intelligence that allows mechanization of the well control manifolds.
Standard Reomte Control Interface - Neometrix
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Integrated Test Rig For HTFE-25 - Neometrix
The purpose of Integrated Test Rig is to assess performance of Fuel Cooled Oil Cooler (FCOC), HP Pump & Oil Pump prior to fitment on Aero Engine. The design of rig is such that it can cater to individual testing of individual LRU or integrated testing of all the LRU’s installed together (in combination). The pumps under test shall be mounted directly on the high-speed electric motor flange through adapter quill shaft assembly. Variable speed drives shall be provided for all the pumps under testing. The rig shall cater for real time monitoring and recording of performance parameters.
KEY FEATURES
Key features of this Rig are as follows: -
1. It has separate power packs for both the fluids i.e. ATF Power pack for ATF Fluid, OX Power Pack for OX-27 Oil.
2. This Rig is designed for high temperature Application. It works on 200 deg. Celsius.
3. Two Dedicated heating systems have been integrated with this Rig to raise the temperature of OX-27 Oil.
4. In both Power Packs insulated tanks are being used, which is good for safe operation and safety of operator.
5. This rig is designed in such a way, that it’s OX power pack is in its left side, ATF Power pack is in right Side and test bed is in Centre.
6. A big Test bed have been provided for smooth testing of UUT’s.
7. All piping is being insulated for safe operation and maintenance.
8. It comprises with DAQ System.
9. This rig can test several components at a time, together or separately.
Application
All the UUT’s are mounted on HTFE-25 Engine after successful performance testing of those. Application of this Rig are as follows: -
1. One of its application is to test LP Pump of HTFE-25. It is designed for functional testing of LP Pump.
a. Free Flow Test
b. Load Test
2. It is used to test HP Pump of HTFE-25. It is designed for functional testing of HP Pump.
a. Free Flow Test
b. Load Test
3. It is used to test Oil Pump of HTFE-25. It is designed for functional testing of Oil Pump.
4. It is used to test FCOC of HTFE-25.
More Related Content
Similar to fuel-consumption-measurement-system.pptx
Continuous boiling point distillation analyser
The ATAC Boilar continuously measures the percent recovered temperatures of petroleum products from 5% to 95% within the distillation temperature range 50°C to 400°C. The Boilar provides fast, continuous, reliable data and is simple to operate and easy to maintain.
Toshniwal - Thermal mass flow meters and controller
THERMAL MASS FLOW METERS AND CONTROLLER
The range of Thermal Mass Flow Meters from Bronkhorst address high accuracy in low flow rate scenarios like those seen in laboratory and Pilot plant usages. With a housing designed for laboratory and clean processing conditions, the instruments are truly unique in their capability to measure and control flow ranges between 0,014…0,7 mln/min and 8…1670 ln/min with pressure rating between vacuum and 400 bar – all in one range of instruments.
FEATURES
Rangeability in digital mode up to 1:150
High accuracy (standard 0,5% Rd plus 0,1% FS)
Pressure ratings 64 / 100 bar
Highly resistant to mechanical shocks and pressure fluctuations
Large range of Input/output options to choose from
Extremely fast and dynamic response
User configurable control characteristics
Applications
Analytical/environmental equipment
Gas flow monitoring in food, chemical and petrochemical industries
Gas consumption measurement in gas distribution systems for internal accounting purposes
Detection of gas leakage through objects
Semiconductor manufacturing
Surface treatment installations
Process Control Fundamentals and How to read P&IDs
Types of Process Control, Feedback control, feed-forward control loops, ratio control loop, split range control. How to read Piping and Instrumentation Diagram for Process Engineers
Instrumentation and process control fundamentals
Basic course covers:
-Basic understanding of process control
-Important process control terminology
-Major components of a process loop
-Instrumentation P&ID symbols
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
RUGGED MONITORING’s R501 is the most versatile and advanced multi-channel monitoring solution. Designed to seamlessly integrate into diverse industries, the R501 stands as a testament to our commitment to innovation and reliability in electrical asset monitoring.
HVAC, Heating Ventilation Air Conditioning BMS
The main purpose of HVAC is to provide the people working inside the building with “CONDITIONED AIR” so that they will have a comfortable and safe work environment.
A BMS system collects the operating information required for intelligent building management.
It analyses the operation of the building systems by viewing all important temperatures, humidities and equipment status.
To:
Ensures energy savings
Improves building operations
Improves building operations allowing remote control/over-ride where necessary
Improves building management by means reporting and traceability
Improves building management by means reporting and traceability
Improves building management by having a faster reaction time to problems
Digital Temperature Controllers
The materials included in this compilation are for the use of Dwyer Instruments, Inc. potential customers and current employees as a resource only. They may not be reproduced, published, or transmitted electronically for commercial purposes. Furthermore, the Company’s name, likeness, product names, and logos, included within these compilations may not be used without specific, written prior permission from Dwyer Instruments, Inc. ©Copyright 2014 Dwyer Instruments, Inc.
Siemens Terminal Box Controller (APOGEE Automation System )
In This PPT we are discussed about complete details of that product (Use,Operation, Technical details, Dimensions, Wiring, and etc..)
Please Support us and Follow our other Sites
https://www.instagram.com/controlsandsystems.offical
https://twitter.com/ControlsSystems
https://automationtechplc2.blogspot.com
https://humidificationcontrol.blogspot.com
https://controlsandsystems.business.site
www.controls.systemsdm@gmail.com
If you enjoyed this article, share it with your friends and colleagues
Emergency Shutdown System, ESD System - Worldwide Oilfield Machine
WOM’s Emergency Shutdown System (ESD) provides a fast acting functional safety shutdown in case of a hydrocarbon escape or other safety issues.
Advanced Control Systems - Worldwide Oilfield Machine
WOM's Advanced Control System software is equipped with intelligence that allows mechanization of the well control manifolds.
Similar to fuel-consumption-measurement-system.pptx (20)
Toshniwal - Thermal mass flow meters and controller
Toshniwal - Thermal mass flow meters and controller
Process Control Fundamentals and How to read P&IDs
Process Control Fundamentals and How to read P&IDs
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
R501 ADVANCED TRANSFORMER MONITOR | Rugged Monitoring
Siemens Terminal Box Controller (APOGEE Automation System )
Siemens Terminal Box Controller (APOGEE Automation System )
Emergency Shutdown System, ESD System - Worldwide Oilfield Machine
Emergency Shutdown System, ESD System - Worldwide Oilfield Machine
Advanced Control Systems - Worldwide Oilfield Machine
Advanced Control Systems - Worldwide Oilfield Machine
More from Neometrix_Engineering_Pvt_Ltd
Standard Reomte Control Interface - Neometrix
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Integrated Test Rig For HTFE-25 - Neometrix
The purpose of Integrated Test Rig is to assess performance of Fuel Cooled Oil Cooler (FCOC), HP Pump & Oil Pump prior to fitment on Aero Engine. The design of rig is such that it can cater to individual testing of individual LRU or integrated testing of all the LRU’s installed together (in combination). The pumps under test shall be mounted directly on the high-speed electric motor flange through adapter quill shaft assembly. Variable speed drives shall be provided for all the pumps under testing. The rig shall cater for real time monitoring and recording of performance parameters.
KEY FEATURES
Key features of this Rig are as follows: -
1. It has separate power packs for both the fluids i.e. ATF Power pack for ATF Fluid, OX Power Pack for OX-27 Oil.
2. This Rig is designed for high temperature Application. It works on 200 deg. Celsius.
3. Two Dedicated heating systems have been integrated with this Rig to raise the temperature of OX-27 Oil.
4. In both Power Packs insulated tanks are being used, which is good for safe operation and safety of operator.
5. This rig is designed in such a way, that it’s OX power pack is in its left side, ATF Power pack is in right Side and test bed is in Centre.
6. A big Test bed have been provided for smooth testing of UUT’s.
7. All piping is being insulated for safe operation and maintenance.
8. It comprises with DAQ System.
9. This rig can test several components at a time, together or separately.
Application
All the UUT’s are mounted on HTFE-25 Engine after successful performance testing of those. Application of this Rig are as follows: -
1. One of its application is to test LP Pump of HTFE-25. It is designed for functional testing of LP Pump.
a. Free Flow Test
b. Load Test
2. It is used to test HP Pump of HTFE-25. It is designed for functional testing of HP Pump.
a. Free Flow Test
b. Load Test
3. It is used to test Oil Pump of HTFE-25. It is designed for functional testing of Oil Pump.
4. It is used to test FCOC of HTFE-25.
Neometrix Optical Balloon Theodolite.pptx
Neometrix Optical Balloon Theodolite
• In common with other land based balloon theodolites the Neometrix theodolite OT-NEA3060 has a telescope with a bent optical axis. A secondary wide-angle telescope using the same eyepiece is selectable with a mirror. There are two pins on the tip of this instrument that serve as contacts to an attachable battery case. The Photo shows the theodolite with the battery case attached.
• In the photo above you can see the bubble level directly under the two switches. The switches control illumination of the reticule and the circles.
• You can see the accessories for this instrument, filters for the eye piece, the key to the case, lens shade, lens cap and a plumb bob. Also note the hook for hanging a stopwatch and the magnifying glass to assist reading the circles.
• Distinguishing features of the OT-NE-A3060 theodolite are the use of a Pentagonal Prism in the bent axis telescope, which allows for better stability of the optical alignment, a closed circle design for durability, two levels of magnification offering wide and narrow fields of view (accomplished with a switchable finder scope using the same eyepiece with two objectives) and a lined gradicule supporting the tail method of altitude determination. The placement of the azimuth and elevation circles directly above each other as well as the use of Micrometer drums facilitates rapid determination of Azimuth and elevation directly to the 10th of a degree.
Dynamometer Engine Test Rig for engines parameters RPM
An Eddy current dynamometer is an electromechanical energy conversion device, which converts mechanical energy to electrical energy. It fundamentally uses Faraday’s Law of electromagnetic induction as its working principle.
In this system we test different ranges of engines RPM, Torque in N-m, and Power. And parameters will be shown in panel.
Power- up to 200 KW
Torque- 1780 N-m
Engine for testing with a range of 1500- 2000 rated rpm.
Engine monitoring system: Control panel with digital meters, oil pressure, lube oil temperature, water temperature, Engine RPM.
Engine parameter recording: A computer based data logger to record engine control parameters. A printer to be provided for printout report of all engines parameter.
And parallel we can record engines parameter like Lube oil pressure, Engine temperature, water temperature etc.
Mechanical Dimensions:-
• Overall Size: 2000 mm x 850mm x 1350 mm
• Centre Height: 900 mm
• Inlet Piping: 2”
• Outlet Piping: 2”
• Calibration Arm Length from centre: 1000 mm
• Cooling Water Requirement (Dynamometer Inlet) Pressure: 1.0-2.0 bars
• Temperature: Less than 40°C.
• Cooling Water Flow (Dynamometer Inlet): 12500 LPH
• Type of Lubrication: Grease (Inner earing), Oil (Outer Bearing)
Electrical:
• Supply Voltage:240 volts ± 10% AC, 50 Hz
• Separate Earth should be given to the system.
• Maximum Excitation: Internally set in the instrument depending on the capacity of Eddy current dynamometer. Generally, 3 To 5 Amps D.C.
• RPM: This is displayed by a 4 digit display. This displays Motor/dynamometer rpm.
• Accuracy: ± 1 rpm.
Environmental:
i) Temperature: 5 to 550C maximum
ii) Humidity: R.H. 95% maximum
Application:
Dynamometer system will test the engines parameters RPM, Torque, Power, Lube oil pressure, temperature, water temperature and result will be shown in control panel with digital meters.
Portable Digital Barometer for Indian Air force
Portable Barometer uses a silicon resonant pressure sensor DPS 8100 producing a pressure reading in pressure measurement units and pressure altitude. It also has a Comptek 10.1" tablet, mounted on an Aluminum enclosure. It can be used as a hand-held indicator tablet or instrument. The instrument can also communicate through a USB connector to extract out logged data. This USB port should be strictly used for App-related data transfer only. The instrument has an in-built tablet which should be used only for the TERPS App. The tablet is provided with a compatible charging adapter. This should be used only to charge the instrument. The instrument should be used within the operating and maximum safe working pressure conditions. Refer to the specification section in this manual for the details.
Sensor Port:
Keep the sensor port clean all the time. Protect the sensor against moisture, water, dirt and dust particles.
Do not block the sensor with any object as it may result in inaccurate reading output.
For better and accurate readings, keep the sensor port away from continuous pressure changing areas (for example, should not be close to AC, Fans, table fans etc.).
During pressure measurement, the device should be placed on the table or held in the orientation.
In case of hand-held application, hold the instrument as shown in Figure 3. While holding the unit, ensure that the hand does not block the sensor port.
USB Port:
This USB Port is specifically for extracting the exported data from the TERPS App. Do not use this port for any other activity. Use this port only for App-related data transfer. When not in use, close the USB port using the rubber cap.
TEST RIG FOR HYDRAULIC FLUID (A3987) - NEOMETRIX DEFENCE
PROJECT: TEST RIG FOR HYDRAULIC FLUID (A3987)
The test rig is used to test the anti-wear properties and the aging
behaviour of hydraulic fluids under defined and reproducible
conditions. For this purpose, a vane pump Vickers 35VQ25A-11*20
for ASTM D6973-2014 and a Bent Axis type axial piston pump
A2F10 for JCMAS P 045 are used as test objects. The subsequent
investigation of the wear inserts and oil condition then allows
conclusions about the performance of the tested fluids, especially
their ability to avoid wear and resist oxidation. The modern and
ergonomically designed test rig meets all the specifications of the
European Machinery Directive 2006/42/EG to a high standard or
equivalent Indian Standard. The test rig is used to determine the
wear characteristics and oxidation/ aging of non-petroleum and
petroleum hydraulic fluids. For this purpose, a rotary vane pump
generates a test pressure under specific boundary conditions. The
result obtained is the total mass loss from the cam ring and the ten
vanes (ASTM D6973-2014) after the test. For indicating oxidation
stability or aging behaviour of hydraulic fluids this test bench, uses a
bent axis pump A2FO10 and a pressure relief valve DBDS 10
K1X/400V as load at high temperatures. The test takes place under
the influence of air and a copper catalyst. This procedure allows for
an accelerated aging rate using a real hydraulic component. The test
rig parameters meet the specifications according to ASTM D6973-
2014 and JCMAS P 045. Additionally, it is capable of carrying out the
evaluation of hydraulic fluid for frictional characteristics and energy
efficiency performance under indigenously developed and
industrially simulated test methods by varying load, speed,
temperature, pressure, flow rate etc.
Hydraulic Loading System - Neometrix Defence
Hydraulic Loading System Serves the following purpose during engine run::
Loads the Engine mounted Hydraulic Pump by Varying the Outlet restriction to achieve specific Flow Rates at specified Pressure Range.
Carry out Cyclic Load Testing of the Hydraulic Pump.
There are six different module which after assembly become complete system.
Modules are following:
Oil tank module
Air Regulation module
Inlet module
Outlet module
Drain module
Loading valve module
Heat exchanger module
Portable oil filling module
KEY FEATURES
Design Pressure : 340 kg/cm2
Working Pressure : 270-295 kh/cm2
Working Flow : 20-210 LPM
Hydraulic Oil : MIL=H-5606/FH-51
Viscosity : 15CST @ 40°C
Density : 0.8735 AT 15.6°C
Tank Capacity : 175 Liters
Tank Max. Pressure : 10 kg/cm2
Max. Temp. at Pump Outlet : 100°C
Max. Temp. at Pump Intel : 80°C
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
The Test Rig is Pneumatic Hydraulic. Safety & user Friendliness are the key features of the provided Test Rig. The Test Rig has been designed to address all the requirements of the Design Document.
With this Test Rig, Operator can work independently.
The entire Test as specified can be done on this Test Rig.
Lock Loading Test Rig (ERU119 & ERU120) .pptx
This rig is designed for testing Ejection Release Units (ERU119 & ERU120) which are tested for Hook Proving Loads. These units are tested for load deformation and the test results will automatically come out as OK/NG on the basis of pre-fed Deformation & Load settings in the system. A self-contained Test Bench is provided to test both types of units.
Mechanical System:
Independent Bench for ERU119 & ERU120 is provided.
Horizontal Loading Facility for the units is provided.
Custom made fixture for holding the units, and unit profile will be accommodated in the fixture so that the unit is not damaged during testing.
LVDT with magnetic contact is provided for displacement measurement.
Both systems have Load Cells with in-situ calibration facility. In- situ calibration will be done automatically.
starter-generator-test-bench-Catalog.pptx
The Following Test Bench is for Testing Parameters of Starter Generator of
Advanced Light Helicopter (ALH).
The Test bench has following four tests :-
1) Generator Mode Load and no Load Test.
2) Starter Mode Load Test.
3) Vibration Measurement Test.
4) Concentricity And Bar to Bar Difference Measurement Test.
Test Bench Description:
This test will have a Combination of AC Motor of 5000 RPM rigidly Coupled with the Dual Output Gear Box having Ratio of 1:3 to give maximum speed of 15000 RPM at output . The output is to accommodate the shaft of 6KW Starter Generator With Suitable Clamping On the Common Flange.
Resistive Load Bank with good Cooling Facility provides load to the Starter Generator in steps of 0,50,100,150 and 200 Amp with additional loads of 300A , 375A and 450 Amp .Load is selected from the control panel through selectable switches.
A.C. Drive ABB make is also provided for this Test with Control signals
From control panel.
45 KVA Ground Power Unit for Raphael .pptx
Ground Power Unit(GPU) is used to give the power to the aircraft which is in the ground during the maintenance and repair work the GPU is used to power up the system externally, This GPU is having Dual output one is 45Kva AC power that consist of L-L 200V and L-N 115V ,150A and 400HZ four wire system another one will be DC 28.5 V 800A two wire system and it will deliver the two output simultaneously up to maximum range of 45 KVA, the following components are used to design the GPU.
Overview: A diesel engine/electric motor coupled with highly reliable alternator provides a perfect output to your aircrafts. With a touchscreen control panel and interactive GUI, this GPU is easy to operate and effortless to maintain. Our AC Ground Power Unit can be supplied with additional 28.5V DC module for obtaining commercial power voltage for tools, appliances. etc. during aircraft maintenance. it is a feature-rich software built for remote operations of GSE with parameter details, fault alarms, alerts and periodic maintenance schedule.
Application
GPU is used to support the aircrafts in ground to maintain and trouble shoot its basic testing with out start up their engine, This will be designed on the required power of aircraft and this whole system is operated by diesel engine , The system is mounted on the portable moving trolley to provide the easy accessibility all over the ground which is towable with necessary braking system.
Printed Circuit Boards (PCBs) PCB-thermal-test-bench.pptx
Printed Circuit Boards (PCBs) need to go through a series of extensive tests and inspections at each step of the manufacturing process to assure the products meets or exceed specifications.
Reliability decreases exponentially in electronic components due to heat problems. Thermal Air series of thermal testing cycling test systems helps manufacturers design ICs, chips, and PCBs for superior thermal performance.
Specifications
Neometrix Thermal Tester is Temperature Forcing Systems and environmental test chambers provide quality assurance through temperature cycling testing. We have used standard highly reliable FLIR camera for thermal scanning.
Thermal Tester is a mobile thermal testing solution capable of environmental stress testing throughout the semiconductor design, manufacturing, and back-end test processes.
Application
Printed Circuit Boards (PCBs) need to go through a series of extensive tests and inspections at each step of the manufacturing process to assure the products meets or exceed specifications.
Reliability decreases exponentially in electronic components due to heat problems. Thermal Air series of thermal testing cycling test systems helps manufacturers design ICs, chips, and PCBs for superior thermal performance.
Key features
Thermal Tester is having following major features:
(a) Wide angle (min 50 degree horizontal) Infrared imaging camera with 640X480 pixels resolution or better.
(b) Thermal analysis software for hotspot and other faults detection.
(c) Automated enclosure with PCB test fixture for testing of PCB of dimension 16X16 inch or better.
(d) Power supply module with minimum eight relay to provide 230VAC/3A/50Hz and 28VDC/5A or better.
(e) Temperatures measurement range: -20 to 200 degrees Celsius.
Optical-test-bench-for-pcb-and-optic-testing.pptx
Optical test equipment or optical measurement equipment are used to measure and characterize the physical properties of light. The insatiable demand for higher capacity in communication networks has fueled the need for highly precise optical test solutions. In addition, precision optical measurements are essential to optical research applications for Defence communication, mobile communication, environmental sensing, and consumer products.
R&D engineers, academic researchers, manufacturing engineers, and field service personnel depend on precision optical test equipment to ensure design and performance specifications, production quality, and network health. For more than 10 years, Neometrix has delivered quality, consistency, ease of use, and market leadership for optical test applications.
Printed circuit board (PCB) FUNCATIONAL TEST BENCH.pptx
Printed circuit board (PCB) functional tester performs critical validation process performed on manufactured PCBs to verify the board’s functionality meets the original design requirements and specifications. Thorough functional testing helps ensure the reliability and performance of PCBs before deployment.
Testing coverage-
Validate continuity and isolation: Verify electrical connectivity and isolation between traces using in-circuit testing (ICT) and flying probe testing to check for opens and shorts.
Confirm impedance: Match measured impedance of traces and interconnects to design values to prevent signal degradation.
Verify power integrity: Check PCB operation under different power conditions to avoid errors from insufficient power delivery.
Assess signal integrity: Examine signal quality under high-speed conditions to prevent distortion and interference.
Test functionality: Stimulate the PCB with input signals and power to check outputs match expected responses based on design.
Confirm robustness: Subject PCB to temperature cycling, vibration, shock to validate resilience and durability.
Execute regression testing: Retest functionality after modifications to ensure no side effects.
Mobile Test Facility (MTF) - Neometrix Defenece
The proposed Mobile Test Facility (MTF) is a roadworthy self-sufficient test facility for testing of “Expandable Turbo Propulsion system (Expandable Engines) of up to 450kgf class” and is devised for Field Tests at various altitude sites in India ranging from sea level to High Altitudes.
“MTF” is proposed with modular design concept, where in each module is built and rigidly installed on a trailer with pre-designated system based on each modules infrastructure functionally required.
It consists Four Trailer mounted Modules-
1. Mobile Utility Trailer Module
2. Mobile Control Cabin Trailer Module
3. Engine Test Section Unit Trailer Module
4. High Pressure Mobile Compressor unit Module (Under GTRE Scope)
Operational Environment :-
1. Test Site Altitude: - From10 m above MSL to 4522 m above MSL
2. Test Site Temperature: -20°C to +50°C
3. Test Site Atmospheric Pressure: 0.57 Atm to 1 Atm
4. Test Site Humidity: 20% to 80%
Electrical General Requirements:
a. Voltage: 415 v ±10%, 3 phase.
b. Frequency: 50 hz +3%, -6%.
c. Aux voltage: 110 VAC (normal supply).
d. UPS voltage - 230 VAC for PLC Panel.
e. 24 V DC Control Circuits.
f. Main switch with emergency stop function.
g. Illuminated double push-button for ON/OFF.
h. Blue illuminated push-button for fault indication and acknowledgement.
i. Control of the test rig and the test programs via operating computer.
modern-universal-automatic-test-equipment.pptx
MODERN UNIVERSAL AUTOMATIC TEST EQUIPMENT(MUATE) is an equipment which is used to perform automatic measurements on the device, known as unit under test (UUT), device under test (DUT), and evaluate the test results. An MUATE has a computer controlled system that contains many complex test instruments that are capable of automatically testing and diagnosing faults in intricate electronic components, PCBs, Integrated circuits. It can test a large range of electronic devices and systems from ingenious components like resistors, inductors, capacitors to complex compiled electronic systems. To accomplish this intention, we are harnessing JIG/Fixture/ITAs.
MUATE systems designed to decrease the amount of test time needed to verify a particular PCB, Component, LRU.
MUATE contains Five subsystem
(a) JTAG
(b) Bed of Nails
(c) Boundary scan
(d) Data acquisition system
(e) Controller
JTAG helps users with PCB debugging, prototyping, testing and repairing.
By using the Bed of Nails (ICT-In circuit testing) we can check for short, open, resistance, capacitance, inductance, tracks, and many more
Components, with the help of boundary scan Test device pin signals or internal signals can be monitored in real-time without interfering with normal operation.
drive-and-control-automation-system.pptx
A drive and control automation system is designed for Helicopter Main Gear Box (MGB) load test rig. The test rig consists of test rig structure in which the MGB of Advanced Light Helicopter (ALH), drive motor, adapter gear boxes are installed. Supplying all hardware & software required for the drive and control automation system for the test rig.
The test rig is a mechanical closed loop system in which the rated speed of MGB is achieved by motor through lower adaptor gearbox. In order to achieve various loads such as thrust loads, torque load and hydraulic pump loads the hydraulic power packs with actuators will be employed. The hydraulic power packs consist of motor pumps, various process switches, sensors valve, etc. which facilitate remote operation of DAS (Data Acquisition System) of the test rig. An AC alternator which is mounted on MGB is to be loaded through resistive load bank with contactor panel.
HYDRAULIC REFILLING TROLLEY - NEOMETRIX DEFENCE
The HYDRAULIC REFILLING TROLLEY is specially designed and developed for the GROUND REFILLING of oil in aircraft systems. It is used for refilling oil in aircraft system through the supplied pressurized hydraulic oil from the trolley to the aircraft, comprising of a pressurized reservoir, with filtered and de- aerated fluid at flow and pressure characteristics required for testing. The Trolley is suitable for wide range of fighter aircraft, military transport aircraft, and helicopters used in Indian Air Force.
This Hydraulic refilling trolley is basically designed for charging Engine oil (Turbonyc Oil-210,Viscosity- 3.7 cst at 100 Deg Celcius )to AIRCRAFT.
Compressed nitrogen is fed from air bottle (BL) along the flexible hose ,through shutoff valve reducers for building up pressure inside the tanks.
The safety valve releases compressed nitrogen into the atmosphere in case pressure exceeds set value.The working fluid displaced by nitrogen pressure from the tank passes through filters and used for cleaning the fluid of mechanical admixtures and gets through aircraft charging adaptor to the AIRCRAFT.
universal-hydraulic-test-bench-aircrafts .pptx
The Neometrix Engineering Series NE-A0107 Universal Hydraulic Test Stands are designed for testing all kind of hydraulic components in various aircrafts & helicopters of Western/ Russian origin like SU-30, Jaguar, Mirage etc.
This is a WORK HORSE required in every ground support & testing establishment.
Virtually any hydraulic component can be tested on this Test Stand by making right hydraulic & electrical connections. It is also very popular with aviation R&D and Product development establishments.
NE-A0107 is heavily used for testing & validating the actuators, valves, accumulators, pumps, hydraulic motors and the hydraulic power packs. Integral drive and integral dynamometer are provided for testing pumps and motors. The NE-A0107 Series Test
Stands are available configured for use with MIL-H-5606, MIL-H-83282, MIL-H-87257 and MIL-H-46170 Hydraulic fluids. Customized OPTIONS are also available.
Key Features:
Cost-effective (International quality, INDIAN PRICE), accurate, automated, software driven, highly capable test system.
Fully Computerized Test Stand. Manual & Semi-Automatic options also available.
National Instruments PXI Based DAQ with Lab View based software
Operating Pressure: up to 3,000 PSI. Flow: up to 20 GPM. Static Pressure: up to 10,000 PSI.
Pumps drive: 5000 RPM, 200 HP. Dynamometer: 5000 RPM, 200 HP. Electrical DC supplies for power packs: 0-32 VDC, 1000 AMP.
Temperature control of hydraulic test circuits. Chilled Water & Air cooled options available.
Six Clamp Perfect Binding Machine
Machine's Salient Features :This is Multi Clamp Perfect Binding Machine, where 6 book clamps travelling in an oval shaped path and done a binding work in a perfect way. 1. In this spine is in line with the crucial binding systems.2. Milling Cutter Comes With Strip Type Cutter and Separate Waste Exhaust System. 3. Gluing System Which has 2 forward rollers and 1 reverse roller (In-built Heating) gives high Quality binding.4. Calibrated head and tail cut offs to avoid adhesive squeeze out.5. Online creasing attachment with Auto Cover feed makes more sense in production.6. Our machine has Optional feeder tray for manual feeding of gate folded covers.7. 'No book-No cover' system ensures the continuous flow of clamps.8. Height and Pressure adjustable ram for book blocks. 9. Moving type Cam Nipping system ensures perfect nipping cover registration.10. Chute delivery system with built in safety systems.
More from Neometrix_Engineering_Pvt_Ltd (20)
Dynamometer Engine Test Rig for engines parameters RPM
Dynamometer Engine Test Rig for engines parameters RPM
TEST RIG FOR HYDRAULIC FLUID (A3987) - NEOMETRIX DEFENCE
TEST RIG FOR HYDRAULIC FLUID (A3987) - NEOMETRIX DEFENCE
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
Hydraulic Hose Leak Testing (Test Rig is Pneumatic Hydraulic).pptx
Printed Circuit Boards (PCBs) PCB-thermal-test-bench.pptx
Printed Circuit Boards (PCBs) PCB-thermal-test-bench.pptx
Printed circuit board (PCB) FUNCATIONAL TEST BENCH.pptx
Printed circuit board (PCB) FUNCATIONAL TEST BENCH.pptx
Recently uploaded
Runway Orientation Based on the Wind Rose Diagram.pptx
Runway Orientation Based on the Wind Rose Diagram
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.
Thank me later.
samsarthak31@gmail.com
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Investor-Presentation-Q1FY2024 investor presentation document.pptx
this is the investor presemtaiton document for qurrter 1 2024
Cosmetic shop management system project report.pdf
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
HYDROPOWER - Hydroelectric power generation
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
在线办理(ANU毕业证书)澳洲国立大学毕业证录取通知书一模一样
学校原件一模一样【微信：741003700 】《(ANU毕业证书)澳洲国立大学毕业证》【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Governing Equations for Fundamental Aerodynamics_Anderson2010.pdf
Governing Equations for Fundamental Aerodynamics
一比一原版(SFU毕业证)西蒙菲莎大学毕业证成绩单如何办理
SFU毕业证原版定制【微信：176555708】【西蒙菲莎大学毕业证成绩单-学位证】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
◆◆◆◆◆ — — — — — — — — 【留学教育】留学归国服务中心 — — — — — -◆◆◆◆◆
【主营项目】
一.毕业证【微信：176555708】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微信：176555708】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
学历顾问：微信：176555708
WATER CRISIS and its solutions-pptx 1234
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Student information management system project report ii.pdf
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Recently uploaded (20)
Pile Foundation by Venkatesh Taduvai (Sub Geotechnical Engineering II)-conver...
Pile Foundation by Venkatesh Taduvai (Sub Geotechnical Engineering II)-conver...
Runway Orientation Based on the Wind Rose Diagram.pptx
Runway Orientation Based on the Wind Rose Diagram.pptx
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
AKS UNIVERSITY Satna Final Year Project By OM Hardaha.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Gen AI Study Jams _ For the GDSC Leads in India.pdf
Investor-Presentation-Q1FY2024 investor presentation document.pptx
Investor-Presentation-Q1FY2024 investor presentation document.pptx
Cosmetic shop management system project report.pdf
Cosmetic shop management system project report.pdf
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdf
Governing Equations for Fundamental Aerodynamics_Anderson2010.pdf
Governing Equations for Fundamental Aerodynamics_Anderson2010.pdf
Student information management system project report ii.pdf
Student information management system project report ii.pdf
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
fuel-consumption-measurement-system.pptx
- 3. This PC based Data Acquisition & Control Software is meant for conducting collapse test of Test Filter. It provides the facility to monitor the input/ output parameters such as Differential Pressure, Flow Rate etc. The solution involves a Data Acquisition, Feedback & Control system that interfaces with Pressure, Temperature, Flow Sensors, Solenoid Valves, Level Sensors & the AC drive.
- 5. Filter Clogging Indicator Switch (6.0) which indicates that the Filter is clogged Tank Weighing System comprising of 4 Load Cells, Flameproof Junction Box & IND 570 Indicator Temperature Sensors installed to monitor the temperature of chilled water as well as the fuel. Ball Valve at the suction of the Fuel Tank Filling Pump is MANUAL and has a limit switch which tells that this Valve is Open Float Switches get activated in case of Fuel Tank overfill or Fuel Tank over flow PLC Controller is connected with Temperature Sensors, Limit Switches on Valves and Filter Clogging Indicator Switches on filters and also Float Switched. PLC Controller is also connected with Chiller through RS485 The HMI on control panel will always show the current status (Open/Close, On/Off) of all components in the Fuel Circuit.
- 7. • Flame Proof ELECTRIC MOTOR : 1.5KW, 1440 RPM,Three PHASE, 4 POLE, 50HZ • Fuel Filter: Filtration :10 Micron(absolute), with electronic Clogging Indicator. • Fuel tank(material ss-304): 150 ltr fuel tank • Temperature sensor (rtd): range: 0 to 100 degree c • Shell & Tube Type Heat Exchanger: Fuel Line Pressure Drop 0.01 Bar. • Refregirated water chiller : Three phase refrigerated air cooled chiller • Ms Sheet Metal Box For Control Panel: 600h X 600w X 350d (Sheet Metal Enclosure With 600x600x350 Mm • Power Supply: 220/4.2a,24v,Dc • Panel Light: Panel Light
- 9. Application This PC based Data Acquisition & Control Software is meant for testing of Life and Efficiency of the Test Filter. It provides the facility to monitor the input/ output parameters such as Differential Pressure, Flow Rate, Temperature etc. The solution involves a Data Acquisition, Feedback & Control system that interfaces with Pressure, Temperature, Flow Sensors, On/Off Valves, Level Sensors, AC drives.
- 11. Thank You