This document provides installation and operation instructions for the EDI-3 Defender Series lift truck impact detection system. It describes how to install the system, set low and high impact values, and use the on-board monitoring. The system consists of a digital indicator, wiring harness and mounting bracket. It detects and displays impact levels in G-forces and can be calibrated by the user. High impacts are recorded and can trigger alarms or notifications.

1. Installation & Operation
EDI-3 Defender Series
Lift Truck On-board Impact Detection & Monitoring
Version:ED!- 3 V1
Integrated Visual Data Technology Inc. 3439 Whilabout Terrace, Oakville, Ontario, Canada L6L 0A7 www.skidweigh.com

2. General Installation Guide
This EDI-3 installation & set up guide describes how to install the unit, input for low / high impact values and use of your
lift truck on-board impact detection system. Following the instructions in this guide will enable you to get your system
operating quickly and easily. In the event that you require additional assistance, please contact customer support via e-
mail at support@skidweigh.com , visit www.skidweigh.com or contact us at the address or contact number below:
Integrated Visual Data Technology Inc.
3439 Whilabout Terrace, Oakville, ON, Canada, L6L 0A7
Phone: 905-469-0985
Safety
Always disconnect the vehicle battery while installing any of the Defender systems or any other electronic product.
Route the cables where they will be protected. Use commonly accepted install practices for after market industrial vehicle
electronic devices. The installation of the Defender systems should only be performed by an acknowledged lift truck
dealer technician or end user electro and hydraulic technical installer.
Here are two acceptable methods of making a wire connections:
* Soldering your connections (recommended)
* Crimp connectors (with the use of the proper crimping tool)
Regardless of the method you choose, ensure that the connection is mechanically sound and properly insulated. Use
high quality electrical tape and shrink tubing where necessary.
This product is connected directly to the vehicle’s ignition switch, 12 to 55 V DC. There is no on-off switch on the unit.
Electro-Magnetic Compatibility
CE conformity to EC directive 89/336 (EMC) by application of harmonized standards: Interference stability EN 61000-6-2
and EN 61326-1 interference emit EN 61000-6-3, EN 61326-1 for the pressure transducer.
EDI-3 Defender Series
Our policy is one of continuous improvement and the information in this document is subject to change without notice.
Check that software version displayed on LCD is the one applicable for your application.
Overview of components
The standard EDI-3 Defender system consist of digital indicator, wiring harness and mounting bracket
Visual Warnings
The standard EDI-3 Defender system shows actual G value in increments of 0.5G on LCD display.
Integrated Visual Data Technology Inc. 3439 Whilabout Terrace, Oakville, Ontario, Canada L6L 0A7 www.skidweigh.com

3. Defender installation precautions
Do not mount Defender indicator to the dashboard plastic surface. The installation on “soft” surface area will act as a
shock absorber and system will not indicate a true impact values.
Selecting the mounting location for Defender
Mount defender indicator in front of the operator . The LCD display of the indicator must be positioned in direction of the
forward travel direction of the vehicle. Digital indicator should be mounted on solid metal surface (dashboard, upper
railing, side railing, etc.). Use Defender metal mounting bracket to fasten the system to the vehicle body. Unit should be
installed in vertical position, +/- 15 degree is allowed for proper operation.
Electrical Connections
All stand alone Defender systems operate from 12 to 55 V DC. There are only two wires to be connected to the vehicle.
RED Wire - Ignition switch
Black Wire - Battery negative or vehicle ground
Integrated Visual Data Technology Inc. 3439 Whilabout Terrace, Oakville, Ontario, Canada L6L 0A7 www.skidweigh.com

4. Defender automatic calibration function
Defender systems are re-calibrated automatically every time power is turned on.
Operation
Depending on the model, standard Defender system does not reqiire any input from the lift truck operator. The LCD
display will show time and date when ignition switch is turned on. There are two lift truck impact detection that will be
shown to the operator. The first one is the “LOW impact”, which will be shown to the operator on LCD display. The
second one is the “High impact” which will be shown on LCD display, audio alarm will be activated for 10 seconds and
the event will be recorder on USB memory stick and / or send to Bolero wireless portal for further analysis.
All “High impacts” events will be recorded on Bolero portal, e-mail notification can be send out, etc.
All impact events are shown to the operator on LCD display in actual G forces.
No Operator ID# Input Operator ID# Input ( Maximum 3 digits )
Operator Input ID#
Enter valid operator ID# (Max. 3 digits) and press Enter key
Optional USB Recordings
Defender units equipped with USB port will record start and finish of the session (Ignition On and Off) and all of the “High
impacts” events.
Default values for “LOW” and “High” impact detections
Factory default value for “LOW Impact” is 1G and for the “HIGH Impact” is 3G.
Integrated Visual Data Technology Inc. 3439 Whilabout Terrace, Oakville, Ontario, Canada L6L 0A7 www.skidweigh.com

5. Default values for “LOW” and “High” impact detections can be changed by
the end user
Depending on your equipment type, lifting capacity and operational environment the end user can easily change factory
default impact values for “LOW” and “High” impact events. It should be noted that “LOW” impact value of 1G is
recommended for majority of operational facilities.
It’s only a visual warning to the operator when vehicles are used in “rough” manner.
How to change factory set impact values
With the LCD display showing date and time, Press IVDT icon located on upper left side of the monitor) and LCD
display will ask for the PASSWORD:
For your system enter a following
PASSWORD number:
and LCD display will show
ENTER LOW IMPACT
0.500g
Press Left or Right arrow to set desired low impact value and than Press Enter Key. After pressing Enter Key the LCD
display will advance to
ENTER HI IMPACT
2.500g
Press Left or Right arrow to set desired High impact value and than Press Enter Key. After pressing Enter Key the
LCD display will go back to normal operational mode showing data and time.
The new modified G set up is done and the new impact values are saved into the system.
Integrated Visual Data Technology Inc. 3439 Whilabout Terrace, Oakville, Ontario, Canada L6L 0A7 www.skidweigh.com