This document summarizes a study that compared the properties and yield of bioethanol produced from mango and orange waste through fermentation. Samples of 100g mango waste, 100g orange waste, and a 50g/50g mixture were pretreated and fermented using Saccharomyces cerevisiae yeast. The highest ethanol yield was 19.98% for mango waste, 19.17% for orange waste, and 17.38% for the mixture. Analysis of variance showed no significant difference in properties except flash point, possibly due to moisture. Producing bioethanol from fruit wastes could provide an eco-friendly fuel alternative while reducing agricultural waste.
BIOETHANOL PRODUCTION TECHNIQUES FROM LIGNOCELLULOSIC BIOMASS AS ALTERNATIVE ...IAEME Publication
Bioethanol production from lignocellulosic biomass (LCB) has been demonstrated as alternative to conventional fuel, as it is considered to be renewable and clean energy. The major problem of bioethanol is the availability of biomass materials for its production. This review paper aims to provide an overview of the recent developments and potential regarding production techniques, ethanol yields, and properties, as well as the effects of bioethanol fuel as replacement for fossil fuel. The literature indicates that the best results have been obtained with cellulase and β-glucanase cocktail which significantly increases bioethanol production compared to fermented acid pretreatment. The classification of pretreatment, hydrolysis, and fermentation have significant effects on physico-chemical properties of bioethanol fuel, which also influence the internal combustion engines. Difference in operating conditions and physico-chemical properties of bioethanol fuels, may change the combustion behaviors and sometimes makes it difficult to analyze the fundamentals of how it affects emissions.
Determination of the Cost of Production from the Raw Dung to the Final Outpu...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
BIOETHANOL PRODUCTION TECHNIQUES FROM LIGNOCELLULOSIC BIOMASS AS ALTERNATIVE ...IAEME Publication
Bioethanol production from lignocellulosic biomass (LCB) has been demonstrated as alternative to conventional fuel, as it is considered to be renewable and clean energy. The major problem of bioethanol is the availability of biomass materials for its production. This review paper aims to provide an overview of the recent developments and potential regarding production techniques, ethanol yields, and properties, as well as the effects of bioethanol fuel as replacement for fossil fuel. The literature indicates that the best results have been obtained with cellulase and β-glucanase cocktail which significantly increases bioethanol production compared to fermented acid pretreatment. The classification of pretreatment, hydrolysis, and fermentation have significant effects on physico-chemical properties of bioethanol fuel, which also influence the internal combustion engines. Difference in operating conditions and physico-chemical properties of bioethanol fuels, may change the combustion behaviors and sometimes makes it difficult to analyze the fundamentals of how it affects emissions.
Determination of the Cost of Production from the Raw Dung to the Final Outpu...theijes
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Land Use Change and European Biofuel PoliciesDavid Laborde
This presentation gives a detailed overview of the 2011 report done by IFPRI (Laborde, 2011) for the European Commission on the land use consequences of EU biofuel mandates (available at http://www.ifpri.org/sites/default/files/publications/biofuelsreportec2011.pdf )
The report aims to compute iLUC (indirect land use change) factor for different feedstocks using the MIRAGE-Biof CGE model.
EXPERIMENTAL AND NUMERICAL INVESTIGATION OF COMBUSTION BEHAVIOUR IN DIESEL EN...Khatir NAIMA
The aim of this investigation is to evaluate the usability of waste polyethylene oil as an alternative fuel for diesel engines. The novel fuel is obtained by a pyrolysis process of waste polyethylene at 973 K. The obtained oil is tested in a single cylinder air cooled (TS1) direct injection diesel engine at 1500 rpm. Engine performances and exhaust pollutant emissions from Waste Polyethylene Oil (WPO) were analysed and compared to those obtained from the same engine fuelled with conventional diesel fuel. Results showed that the total fuel consumption of WPO is lower than that of neat diesel fuel due to the higher heating value of WPO. Brake Thermal Efficiency (BTE) is improved for WPO especially at low load. The exhaust gas temperature is lower for WPO than that of diesel at low and full load. CO and UHC are found lower, while NOx emissions are higher at high loads. Furthermore, the use of numerical investigation permits to optimize the injection parameters, which can help to take advantages of WPO fuel. The simulation results suggest advancing the injection timing.
biofuels, first and second generation biofuels, their history, biodiesel, mass production, applications, properties, fuel efficiency, emissions, material compatibility, availability and prices
USAGE OF ETHANOL BLENDED PETROL: EXPERIMENTAL INVESTIGATIONS OF REDUCTION IN ...P singh
An experimental study was conducted to evaluate what extent ethanol blends in Petrol helps in reduction of pollution levels of SI engines exhaust emissions. Ethanol blends E5, E10, E15, E20, E22 were tested and found considerable reductions in the pollutant levels of CO, CO2, HC. The results indicate better combustions in petrol engine with ethanol blends. The reductions in HC and CO were to the extent of 80% to 90% compared to pure petrol fuelled IC engine.
“Sweet Sorghum – A Novel Opportunity for Biofuel Production”.pptxAvinashJoshi53
Biofuel, any fuel that is derived from biomass—that is, plant or algae material or animal waste. Sweet sorghum [Sorghum bicolor (L.) Moench.] produces food (grain) and fuel (ethanol from stem sap) and the stalks contain 10-15 % sugars. Ethanol obtained from sweet sorghum is considered “cleaner” than ethanol from other sources.
Sweet sorghum is a promising dryland biofuel feedstock that addresses food-verses-fuel issue favourably.
Bioethanol from sweet sorghum (sorganol) is potentially a win-win solution.
Enhance energy security, ecological and economical sustainability and livelihood development.
Land Use Change and European Biofuel PoliciesDavid Laborde
This presentation gives a detailed overview of the 2011 report done by IFPRI (Laborde, 2011) for the European Commission on the land use consequences of EU biofuel mandates (available at http://www.ifpri.org/sites/default/files/publications/biofuelsreportec2011.pdf )
The report aims to compute iLUC (indirect land use change) factor for different feedstocks using the MIRAGE-Biof CGE model.
EXPERIMENTAL AND NUMERICAL INVESTIGATION OF COMBUSTION BEHAVIOUR IN DIESEL EN...Khatir NAIMA
The aim of this investigation is to evaluate the usability of waste polyethylene oil as an alternative fuel for diesel engines. The novel fuel is obtained by a pyrolysis process of waste polyethylene at 973 K. The obtained oil is tested in a single cylinder air cooled (TS1) direct injection diesel engine at 1500 rpm. Engine performances and exhaust pollutant emissions from Waste Polyethylene Oil (WPO) were analysed and compared to those obtained from the same engine fuelled with conventional diesel fuel. Results showed that the total fuel consumption of WPO is lower than that of neat diesel fuel due to the higher heating value of WPO. Brake Thermal Efficiency (BTE) is improved for WPO especially at low load. The exhaust gas temperature is lower for WPO than that of diesel at low and full load. CO and UHC are found lower, while NOx emissions are higher at high loads. Furthermore, the use of numerical investigation permits to optimize the injection parameters, which can help to take advantages of WPO fuel. The simulation results suggest advancing the injection timing.
biofuels, first and second generation biofuels, their history, biodiesel, mass production, applications, properties, fuel efficiency, emissions, material compatibility, availability and prices
USAGE OF ETHANOL BLENDED PETROL: EXPERIMENTAL INVESTIGATIONS OF REDUCTION IN ...P singh
An experimental study was conducted to evaluate what extent ethanol blends in Petrol helps in reduction of pollution levels of SI engines exhaust emissions. Ethanol blends E5, E10, E15, E20, E22 were tested and found considerable reductions in the pollutant levels of CO, CO2, HC. The results indicate better combustions in petrol engine with ethanol blends. The reductions in HC and CO were to the extent of 80% to 90% compared to pure petrol fuelled IC engine.
“Sweet Sorghum – A Novel Opportunity for Biofuel Production”.pptxAvinashJoshi53
Biofuel, any fuel that is derived from biomass—that is, plant or algae material or animal waste. Sweet sorghum [Sorghum bicolor (L.) Moench.] produces food (grain) and fuel (ethanol from stem sap) and the stalks contain 10-15 % sugars. Ethanol obtained from sweet sorghum is considered “cleaner” than ethanol from other sources.
Sweet sorghum is a promising dryland biofuel feedstock that addresses food-verses-fuel issue favourably.
Bioethanol from sweet sorghum (sorganol) is potentially a win-win solution.
Enhance energy security, ecological and economical sustainability and livelihood development.
MADEIRA 2008 - Congresso Internacional de Desenvolvimento Econômico Sustentável da Indústria de Base Florestal e de Geração de Energia, 10 e 11 de Dezembro, Hotel Plaza São Rafael, Porto Alegre, RS.
Similar to Comparism of the Properties and Yield of Bioethanol from Mango and Orange Waste (20)
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Overview of the fundamental roles in Hydropower generation and the components involved in wider Electrical Engineering.
This paper presents the design and construction of hydroelectric dams from the hydrologist’s survey of the valley before construction, all aspects and involved disciplines, fluid dynamics, structural engineering, generation and mains frequency regulation to the very transmission of power through the network in the United Kingdom.
Author: Robbie Edward Sayers
Collaborators and co editors: Charlie Sims and Connor Healey.
(C) 2024 Robbie E. Sayers
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
2. Maina et al.: Comparism of the properties and yield of bioethanol from mango and orange waste.
AZOJETE, 13(6):779-789. ISSN 1596-2490; e-ISSN 2545-5818, www.azojete.com.ng
780
wastes and biomass consisting of all growing organic matter (plants, grasses, waste fruits and
algae) to fuel would ensure a continual energy supply (Wyman, 1994). According to the United
State Department of Energy, for every unit of energy consumed for bioethanol production, 1.3
units of energy are returned Hil, et, al. (2006).
Agricultural waste from fruits like mango and orange are plant- based material that can be an
ethanol feedstock. All plants contain sugars, and these sugars can be fermented to make ethanol
in a process called biochemical conversion. Plant material can also be converted to ethanol using
heat and chemicals in a process called thermo chemical conversion. These agricultural waste
fruits (mango and orange) generate solid waste and economic losses to farmers both in the farm
and the market places, therefore, the use of these waste for bioethanol production shall reclaim
the farmers economic loss and rid the environment of the negative impact of these waste, Lo, et
al,(2009). The high rate of Nigeria’s dependency on crude oil and the consequences of using
fossil fuel (high rate of greenhouse gasses generation) require immediate attention with respect
to the production of bioethanol for blending with fossil fuel in order to produce a much cleaner
and eco-friendly fuel (lower rate of greenhouse gasses generation) for use in our machinery.
Ethanol, also known as ethyl alcohol with the chemical formula C2H5: “The fuel of the future is
going to come from fruit like (mango and orange waste) that’s out by the road, or from apples,
weeds, sawdust – almost anything that’s plant based. There is fuel in every bit of vegetable
matter that can be fermented. There is enough alcohol in one year's yield of an acre of potatoes to
drive the machinery necessary to cultivate the fields for a hundred years, Saratale et al., (2008).
However, fossil fuels were pre-dominantly used for automobile transportation throughout the last
century, obviously due to their lower production cost. As an automotive fuel, hydrous ethanol
can be used as a substitute OH, is a flammable, clear, colorless and slightly toxic chemical
compound with acceptable odour. It can be produced either from petrochemical feedstock by the
acid-catalyzed hydration of ethene, or from biomass feedstock through fermentation. On a global
scale, synthetic ethanol accounts for about 5-10% of total production while the rest is produced
from fermentation of biomass mainly sugar crops, e.g. cane and beet, and of grains (mainly
corn). Ethanol as a neat fuel or even in the blended form with gasoline has a long history as
automotive fuel. In 1860, German inventor Nicholas Otto used ethanol as a fuel in an early
prototype of an internal combustion engine because it was widely available throughout Europe
for use in spirit lamps. A few years later, Henry Ford built his first automobile with an engine
that could run on ethanol. In 1908, Ford unveiled his Model T engine equipped with carburetors
that could be adjusted to use alcohol, gasoline or a mixture of both fuels. Ethyl alcohol as "the
fuel of the future" was presented by him for the first time. Anhydrous ethanol, on the other hand,
is an effective octane booster when mixed in blends of 5% to 30% with no engine modification
requirement.
This study is aimed at producing bioethanol from waste fruits of Mango (Mangifera indica) and
Orange (citrus) by fermentation process using rotten potatoes and tomatoes as vegetable medium
(potatoes dextrose agar) to generate enzymes for the fermentation process; the extracted
3. Arid Zone Journal of Engineering, Technology and Environment, December, 2017; Vol. 13(6):779-789.
ISSN 1596-2490; e-ISSN 2545-5818; www.azojete.com.ng
781
bioethanol properties shall be compared with standard pure (98%) hydrous ethanol in order to
identify the waste fruit with the highest yield.
2.0 Materials and Methods
The basic biology behind bioethanol production is the action of microorganism in the form of
yeast anaerobic on sugar containing solution and its subsequent conversion into alcohol. The
reaction involved can be represented by the following equations.
Sugar + yeast → ethanol + carbon dioxide……………………………………………..2.0
C6H12 + yeast → 2C2H5OH + 2CO2 …………………………………………..………2.1
Starch with the chemical formula C6H10O5 is first of all converted to glucose which is then
fermented into bioethanol using the equipment and reagents mentioned in the chemical equations
show these transformations as follows
Starch + water →glucose…………………………………………………….……….....2.2
C6H10O6 + H2O → C6H12O6……………………………………………….………..…2.3
2.1 Materials and equipment used
Waste fruit samples of equal weight (100g) of mango ( ) orange ( ) and equal proportion of the
two samples put together as the third sample (mango and orange), were collected from gamborou
market in Maiduguri (fruits major market), Borno state Nigeria. Waste potatoes and tomatoes for
vegetable medium preparation were also collected at the same market. refractometer, autoclave
machine, conical flasks, spatula, industrial oven, pycnometer, thermostat, test tubes,
thermometer, flash point apparatus, distillation apparatus, pH paper and meter, dry active yeast,
yeast extract, Sodium chloride, magnesium chloride, sodium nitrate and potassium chloride as
mineral salt medium (MSM), lactic acid, lactic phenol and dextrose (for synthetic nutrient broth),
sodium hydroxide for pH correction, sulphuric acid for hydrolysis, 98% pure ethanol (used to
prepare standard curve for ethanol), de-ionized water, pipette, buffer solution, and U-tubes
capillary viscometer.
2.2 Methods
2.2.1 Experimental procedure (Preparation and Sterilization of Growth Media)
All the glasses were put in a container with tap water and liquid wash was added and left to stay
for 10-15 minutes and then washed with a clean water to remove all stains and impurities; finally
they were rinsed with distilled water, and sterilized with hot air in an oven for 30 minutes at a
temperature of 180O
C (Adney, 1996). 200 grams of potatoes was peeled, shed and boiled in a
conical flask for 20 minutes, it was turned into another conical flask and filtered. The filtrate was
mixed with dextrose. Another conical flask was boiled with water inside it and nutrient agar was
poured little by little and stirred to avoid formation of lumps. The dextrose with the filtrate was
mixed with agar solution (as our growth media). When a complete solution of potatoes dextrose
agar (PDA) was achieved the conical flask was corked with a large amount of non-absorbent
4. Maina et al.: Comparism of the properties and yield of bioethanol from mango and orange waste.
AZOJETE, 13(6):779-789. ISSN 1596-2490; e-ISSN 2545-5818, www.azojete.com.ng
782
wool to prevent contamination and then covered with aluminum foil. The flask was sterilized in a
clinical autoclave for 20 minutes at a maximum temperature of 120°
C and operating pressure of
15 Psi, Mamma et al., (2008). The cotton plug was wrapped with aluminum foil to avoid
possible moistening of the plugs by condensing steam. On attaining the required sterilization
period (20mins) the clinical autoclave was switched off and cooled to room temperature. The
sterilized and cooled medium was stored in a refrigerator.
2.2.2 Microorganism culturing and acidified solution for Pons culture
Lactic acid was prepared into a solution of 59 percent lactic acid with distilled water to prevent
the activities of bacteria in the culture medium (Adney, 1996) The potatoes dextrose agar (PDA)
medium already prepared in the clinical autoclave, was cooled to a temperature of 40o
C before it
is poured into the sterilized Petri dishes, 59 percent of lactic acid was poured into each of the
Petri dishes to acidify the dishes, the medium poured into the Petri dishes was allowed to cool to
room temperature, solidify and ready for culturing. The inoculating loop was sterilized with
alcohol (methylated spirit) and heated with spirit lamp until is partially red hot. The inoculating
loop was first put in the acidified culture medium to reduce the needle temperature. The loop was
then used to cut a portion of the Parent culture from visible matured strain, which is immediately
put in the counter of the freshly acidified and cooled medium Ban-Koffi, et al, (1990) as shown
in Figure 1.
Figure 1: The Pure culture preparation (Anas, 2015)
2.2.3 Sample collection and preparation
The sample of waste mango used for the extraction of bioethanol is shown in Figure 2. Where
A1 is the raw mango, A2 is the dried peeled with pulp and A3 is the grinded rotten mango.
A1 A2 A3
Rotten mango peeled dried mango grinded mango
Figure 2: The mango sample
5. Arid Zone Journal of Engineering, Technology and Environment, December, 2017; Vol. 13(6):779-789.
ISSN 1596-2490; e-ISSN 2545-5818; www.azojete.com.ng
783
The sample of waste orange used for the extraction of ethanol is shown in Figure 3. Where B1 is
the raw orange, B2 is the dried peeled with pulp and B3 is the grinded rotten orange.
B1 B2 B3
Rotten orange peeled dried orange grinded orange
Figure 3: The orange sample
C1 C2
50% dried mango 50% dried orange
Figure 4: Ratio of sample A and sample B before mixing to form sample C.
2.2.4 Preparation of substrate
The choice of the substrate was 2 different varieties of waste fruits (mango and orange). The
waste fruits was peeled, sliced in to pieces and allowed to sundry which is then grinded into
powder form as in figures 2, 3 and 4. The powder form of waste fruits were weighed with
electronic weighing machine (model mp 1002, made in Japan) into 3 different samples i.e. A, B
and C, 100g of orange, 100g of mango and a mixture of orange and mango at equal proportions
(fig. 4) 50g of each respectively which was put into transparent gallons, 600ml of mineral salt
medium (MSM) was poured into each sample mixed and tight the gallons properly for
fermentation to take place as shown in Figure 5.
Figure 5: The Substrate preparation (Anas, 2015)
6. Maina et al.: Comparism of the properties and yield of bioethanol from mango and orange waste.
AZOJETE, 13(6):779-789. ISSN 1596-2490; e-ISSN 2545-5818, www.azojete.com.ng
784
2.2.5 Inoculating the substrate
The inoculating loop was sterilized with cotton wool soaked with 70% alcohol to destroy any
existing contamination. A well developed colony of the already sub-cultured pure specie of
saccharomyces cerevisiae was taken using the inoculating loop, which was dipped into the
substrate and mixed properly, Manikandan, et al, (2008). This process was repeated for the
remaining samples inside the gallons.
2.2.6 Observation of activity of the microorganism
Observation of the activity of the microbes was done on a daily basis as the change in glucose
concentration of the samples were measured and recorded in the three sample shown in plate 2.6.
where anaerobic reaction/digestion is taking place.
Plate 2.6: The fermentation of three samples (Anas, 2015)
2.2.7 Tests for glucose
The glucose test was carried out using the Randox standard glucose kit. This was done first by
preparing the sample, the standard before the analysis of the entire sample involved 4 ml of
filtrate taken from the conical flask and transferred using a pipette into the test tube, 1 ml of the
reagent is added into it. The test for glucose was carried out using spectrophotometer, 4 cubes
were used, the first cube was used as a blank where only distilled water was poured and in the
other 3 cubes, the samples solution weighing 100g each was poured unto the cubes inside the
spectrophotometer machine and the amount of glucose was measured. The amount of glucose
measured was directly proportional to the amount of bioethanol been formed in the sample
solution, Reddy, et al., (2011).
2.2.8 Determination of the properties of ethanol
2.2.9 Distillation range test
A known volume of the bioethanol was turned into ASTM distillation flask fixed at it position. A
thermometer inserted at the top and switched on. A receiver (cylinder) was kept at the distillate
recovery point. The temperature reading was taken at the first drop at the distillate. As the
temperature increased, the distillate increased in volume until there was a decrease in distillate
and at the last drop the final temperature and volume were noted, Adney, et al., (1996).
Appearance: the distillate was observed visually, using visual test method.
7. Arid Zone Journal of Engineering, Technology and Environment, December, 2017; Vol. 13(6):779-789.
ISSN 1596-2490; e-ISSN 2545-5818; www.azojete.com.ng
785
2.2.10 Ethanol yield
Bioethanol concentration was monitored following the method described by Adney, et al.,
(1996) using refractive index method. The refractive index was determined with refractometer
(Bellingham and Stanley, England 366A-3R). A calibration curve was obtained initially by
diluting pure 98% ethanol in water to obtain different concentrations of bioethanol and their
corresponding refractive index obtained from the refractometer, while percentage yield of each
sample was determined by the formula; Yield point % = (sample weight/mass of sample
distillate) × 100, Adney, et al., (1996).
2.2.11 Flash point
This test was carried out using penskymartens flash point apparatus. The cup in the apparatus
was dried. 50 ml of each sample (ethanol produced) was transferred into the position in the
apparatus assembled with thermometer and the apparatus was switched on, the heat was
controlled by a steady stirrer to maintain a uniform temperature while passing a small flame
across the material every five seconds. The temperature at which the vapor first flashes with the
blue flame was recorded as the flash point of the samples after each test cup was washed and
dried before the subsequent test, Adney, et al., (1996).
2.2.12 PH test
The PH meter probe was first inserted in a buffer solution to standardize the apparatus then
placed into the sample (bioethanol) and then the readings were obtained.
2.2.13 Density and specific gravity test
Empty pycnometer was weighed. The pycnometer was filled with sample (ethanol) the excess
was wiped off, the weight was recorded and density is calculated using the formula
Density ( ) = or Density =
–
–
Where M2 = mass of empty bottle in (g), M1 = mass of empty bottle + water in (g)
M0 = mass of the substance in (g)
Secondly distilled water was filled into the pycnometer, weighed and recorded. The specific
gravity was calculated using the formula
Specific gravity (spg) = density of bioethanol/density of water.
2.2.14 Viscosity test
50 ml of bioethanol was turned into A-arm of tube capillary viscometer through the orifices to
the marked point; a sucker was used to lift the sample to the b-arm of the capillary to the marked
point. A stop watch was used to regulate the time it took the bioethanol to return (flow) to the
mark under the B-arm and the time noted. Viscosity calibration curve was then used to convert
viscosity in seconds to centistokes, Adney, et al., (1996).
8. Maina et al.: Comparism of the properties and yield of bioethanol from mango and orange waste.
AZOJETE, 13(6):779-789. ISSN 1596-2490; e-ISSN 2545-5818, www.azojete.com.ng
786
2.2.15 Boiling point
Boiling point is the temperature at which the vapor pressure is equal to atmospheric pressure and
was determined by noting the reading of the inserted thermometer through the cork covering the
conical flask containing the sample being heated.
3.0 Results and Discussion
The result in table 1 shows an increase in PH value for each different samples as fermentation
increases, which also shows that the acidity concentration of all the samples are decreasing while
fermentation rate increases since the PH value was moving towards basicity.
Table 1: pH values obtained from each sample during first week of fermentation
Time (hrs) Sample A
(mango waste fruits)
Sample B
(orange waste fruits)
Sample C
(mango and orange)
24 5 5.16 5.08
48 5.26 5.18 5.22
72 5.45 5.6 5.23
96 5.84 5.64 5.74
120 6.5 6.23 6.37
144 6.85 6.60 6.73
168 6.72 6.81 6.77
The result in table 2 shows that glucose concentration and absorbance from sample A increases
more rapidly than the other sample at first week of fermentation, this because sample A has
lower acid content that requires less time to digest and ferment subsequently as compared to
orange with higher acid content and requires more time to digest before fermentation.
Table 2: Glucose test results obtained from each sample during first week of fermentation at
intervals of two days.
Sample Time (hrs) Quantity (g) Absorbance Conc. Mol/L Conc. %
A(mango) 48 100 1.983 1.991 x 10-3
0.199
B(orange) 96 100 1.944 1.951 x 10-3
0.195
C(mango-orange) 144 100 1.843 1.835 x 10-3
0.184
The result of Table 3 shows that sample A has the least percentage of moisture content but
highest percentage of ethanol while sample B has the highest percentage of moisture content
with the least percentage of ethanol using the same quantity of sample i.e. (100g each).this may
be attributed to the sample’s low acid content compared to samples B and C both having orange
with high citric acid content, The concentration of bioethanol in sample A can be due to the
effective activity of the sacchromyces cerevisiae as enzymes for the production of ethanol which
is similar to the work of Talebnia, (2008).
Table 3: Percentage of moisture content and bioethanol from each sample during first stage of
distillation
9. Arid Zone Journal of Engineering, Technology and Environment, December, 2017; Vol. 13(6):779-789.
ISSN 1596-2490; e-ISSN 2545-5818; www.azojete.com.ng
787
Sample Mass (g) Volume of ethanol – water
mixture (ml)
Moisture
content (%)
Ethanol
(%)
A(mango waste) 100 590 23.73 76.27
B(orange waste) 100 521.6 29.00 71
C(mango and orange) 100 575.5 25.20 74.8
The result of Table 4 and 5 represent the density of ethanol at first and second stage of
distillation which show that sample A of Table 4 has the least density of 8.48 kg/m3
with a
volume of 5.9 x 10-4
m3
while sample C has the highest density of 9.43 kg/m3
with a volume of
6.1 x 10-4
m3
. Similarly, in Table 5 the volume of each sample decreases and the density
increases, sample also decreases. This shows that sample A is less dense and has 793.30 kg/m3
with 4.5 x 10-4
m3
while sample C is denser and has 813 kg/m3
with 4.3 x10-4
m3
, this confirms
that the density of sample C is as a result of it mass and volume in both first and second
distillation as clearly shown in both Tables.
Table 4: Density of ethanol- water mixture of each sample at first stage distillation
Sample Mass (m) (kg) Volume (V) (m3
) Density (ℓ ) (kg/m3
)
A(mango waste) 0.5006 5.9 x 10-4
8.48
B(orange waste) 0.5216 5.8 x 10-4
8.99
C(mango and orange) 0.5755 6.1 x 10-4
9.43
Table 5: Density of ethanol at second stage of distillation
Sample Mass (M2) (kg) Volume (V2) (m3
) Density (ℓ2) (kg/m3
)
A(mango waste) 0.357 4.5 x 10-4
793.30
B(orange waste) 0.296 3.7 x 10-4
800.00
C(mango and orange) 0.350 4.3 x 10-4
813.00
The yield result of the composition showed an increase in the ethanol production (Table 6) for
sample A (rotten mango) and decrease in sample C (orange and mango). The fermentation of
waste fruits by saccharomyces cerevisiae for ethanol production had a high percentage of
ethanol. For this research the overall percentage of ethanol produced did not exceed 19.98% for
sample A(waste mango), 19.17% for sample B (orange) and 17.38% sample C (orange and
mango). The yield which is generally low is due to small amount of sample used.
Table 6: Percentage of ethanol yield from each sample used
Sample Mass (g) Volume (ml) Yield point (%)
A(mango waste) 100 500.6 19.98
B(orange waste) 100 521.6 19.17
C(mango and orange) 100 575.5 17.38
Table 7 shows the results of the estimated mean properties of the Bioethanol investigations
carried out with respect to waste fruits of mango and orange as the feed stock.
The results in table 7 were further subjected to statistical analysis (ANOVA) using Duncan
Multiple Range Test (DMRT) of the fuel properties of ethanol samples. It is obvious from the
10. Maina et al.: Comparism of the properties and yield of bioethanol from mango and orange waste.
AZOJETE, 13(6):779-789. ISSN 1596-2490; e-ISSN 2545-5818, www.azojete.com.ng
788
result in table 8 that the observed differences were not significant, however, the mean treatment
difference observed between sample 1 and 4, sample 2 and 4, and sample 3 and 4 for the flash
point were significant at 5% level. This is probably due to high moisture present in the three
samples compared with the control sample (sample 4). This is responsible for the lower flash
point of sample 4 compared to that of samples 1, 2 and 3 in Table 7.
Table 7. Estimated Mean of Ethanol Properties
Flash
point
Boiling
Point Viscosity pH
Refractive
Index
Relative
Density
Specific
gravity
1-Ethanol from MANGO 28.6 79.6 1.4 5.3 1.36 0.91 0.79
2- Ethanol from ORANGE 30.2 81.3 1.8 4.8 1.35 0.97 0.8
3-Ethanol from MANGO/ORANGE 29.7 83.5 1.7 3.9 1.34 0.96 0.81
4-ETHANOL 12.2 78.3 1.09 5.2 1.35 0.78 0.79
Table 8. Mean Treatment Difference of Ethanol Properties
Flash
Point
Boiling
Point Viscosity pH
Refractive
Index
Relative
Density
Specific
gravity Df
1 vs 2 -1.6 -1.7 -0.4 0.5 0.01 -0.06 -0.01 1
1 vs 3 -1.1 -3.9 -0.3 1.4 0.02 -0.05 -0.02 1
1 vs 4 16.4 1.3 0.31 0.1 0.01 0.13 0 1
2 vs 3 0.5 -2.2 0.1 0.9 0.01 0.01 -0.01 1
2 vs 4 18 3 0.71 -0.4 0 0.19 0.01 1
3 vs 4 17.5 5.2 0.61 -1.3 -0.01 0.18 0.02 1
Where 1= Ethanol from Mango; 2= Ethanol from Orange; 3= Ethanol from Mango/orange;
4=Ethanol
4.0 Conclusion
Bio-ethanol has been extracted from waste fruits of mango and orange in equal proportion
through fermentation process (sample A, B and C). Sample A (mango waste fruit) was identified
as the feedstock with the highest yield of 19.98% among the Three samples. Sample B (orange
waste fruit) yielded 19.17% while sample C (mango and orange waste fruits in equal proportion)
yielded 17.38% of bio-ethanol. The properties of extracted bioethanol were compared with
standard ethanol, the properties showed similarities within 5% (average error) when analysed
using the Duncan multiple range test (DMRT) in design expert 7.0 statistical package, which was
in agreement with that of pure ethanol requiring 5-10% gasoline addition for de-naturing before
use. Furthermore, ethanol at the first stage of distillation produced should be subjected to another
distillation or separation method such as fractional distillation, membrane separation etc, this is
to refine the process in order to separate ethanol from water for absolute combustibility.
The study further shows that waste fruits (mango and orange) can be put to use by increasing the
scale of use of these waste material for bio-ethanol production. It also minimizes the economic
loss that may be accrued to the waste fruits and by extension contributes immensely to carbon
sequestration.
11. Arid Zone Journal of Engineering, Technology and Environment, December, 2017; Vol. 13(6):779-789.
ISSN 1596-2490; e-ISSN 2545-5818; www.azojete.com.ng
789
For further research, more varieties of waste fruits should be used so as to know which variety
will produce ethanol optimally.
References
Adney B. and Baker J., 1996. Measurement of Cellulase Activities, Laboratory Analytical
Procedure (LAP), NREL National Renewable Energy Laboratory, Florida.
Anas, B., Mustapha, A. and Binyaminu, U., 2015. Production, characterization and performance
Evaluation of ethanol from waste fruits (mango and orange) as an alternative fuel in internal
combustion engine (I.C.E)” unpublished graduate thesis.
Ban-Koffi, L. and Han, YW. 1990. Alcohol production from pine apple waste. World Journal of
Microbiology and Biotechnology, 6(3), 281-284.
Hill, J., Nelson, E., Tilman, D., Polasky, S. and Tiffany D. 2006. Environmental, economic, and
energetic cost and benefits of biodiesel and ethanol fuels. P. Natl. Acad Sci USA 103:11206-
11210.
Manikandan, K., Saravanan, V. and Virurhagiri, T. 2008. Kinetics studies of ethanol production
from banana peel waste using mutant strain of Saccharomyces cerevisiae. Indian journal of
Biotechnology, 7:83-88.
Mamma D., Kourtoglou E., and Christakopoulos P. 2008. Fungal multienzyme production on
industrial by-products of citrus-processing industry, Bioresource Technology 99 2373-2383.
Reddy, LV., Reddy, OVS. and Wee, YJ. 2011. Production of ethanol from mango (Mangifera
indica) peel by Saccharomyces cerevisiae CFTRI101. African Journal of Biotechnology, 10(20),
4183-4189.
Saratale, GD, Chen SD., Lo, YC, Saratale, RG, and Chang, JS. 2008. Outlook of biohydrogen
production from lignocellulosic feedstock using dark fermentation -a review. J. Sci. Ind. Res.
67: 962-979.
Talebnia F., 2008. Ethanol production from Cellulosic Biomass by Encapsulated
Saccharomycscerevisiae, 2008. Department of Chemical and Biological Engineering, Chalmers
University of Technology, Göteborg, Sweden
Wyman, CE.1994. Ethanol from lignocelluloses biomass, Technology, economics and
Opportunities. Bioresources Technol. 50: 3-16
Celik, MB. 2008. Experimental determination of suitable ethanol-gasoline blend rate at high
compression ratio for gasoline engine”; Applied Thermal Engineering, 2008, 28 pp. 396–404
http://www.eesi.org/files/Robert_McCormick_061215.pdf, accessed October 21st, 2015;
Lo YC, Saratale GD, Chen WM, Bai MD, Chang JS (2009).Isolation of cellulose-utilizing
bacteria for cellulosic biohydrogen production. Enzyme Microb. Technol. 44: 417- 425.